Professional Documents
Culture Documents
KORG KROSS Service Manual
KORG KROSS Service Manual
MUSIC WORKSTATION
KROSS
KROSS-61/88
SERVICE MANUAL
TABLE OF CONTENTS
ASSEMBLY SKETCH (HOOKUP): 2
BLOCK DIAGRAM: 5
SCHEMATIC DIAGRAM: 6
TEST MODE: 12
PARTS LIST: 27
3. Internal inspection
When Figure 1 will be displayed during the inspection, there
is a failure.
Figure 2
If there is a NG item in internal inspection, Figure 3 is displayed in Figure 2 is not displayed.
Figure 3
Close by pressing the [FUNCTION].
Defect step number is displayed inspection faulty
items will be displayed and NG.
Make sure at the end of the section of the test
mode "Internal inspection NG correspondence
table".
Figure 4
(Caution)
Data of PCM ROM will be broken when the power is turned off during an internal
inspection.
Screen shown in Figure 4 to appear, do not turn off the power.
Figure 9
5-4. SW & LED inspection
This test is started, SW1 LED is lit.
"Table 1 is the order of inspection.
Please press the button on the cell to the right of the lit LED.
When pressed correctly, LED of the next line of the table is lit."
Make sure that there is no place that is very dark place and is extremely bright lights of the LED.
"Please make sure that you do not scrub is when you press the button.
Please make sure that there are no SW KNOB does not return it stuck."
"LED lighting confirmation of all is finished,
Please proceed to the test by pressing the [16] button."
6. LCD inspection
Inspection of the LCD, make sure that no scratch, cracks in the glass.
Make sure that there is no foreign matter such as dust between the LCD and PANEL SHEET.
6-1. Solid black LCD display inspection
Please make sure that there are no missing dots in solid black LCD display, which is displayed as
shown in Figure 10
Figure 10
6-2. LCD white solid display inspection
Please make sure that there are no missing dots in white solid LCD display, which is displayed as
shown in Figure 11
Figure 11
Figure 12
Figure 13
After adjusting, please let proceed to the next test by pressing the [ENTETR].
Figure 14
Where it stops,
numbers enclosed in square yellow 14 figure, make sure that it is "00000".
"To return to the center and release your finger from the WHEEL.
Please make sure that the right of ""CENTER"" of the LCD displayed ""press [SW1] to valid"" and like
a 14 figure."
"Rotate the wheel until upper ends.
Remove your hand from the wheel and confirm that the wheel returned to the center position
smoothly.
Rotate the wheel until lower ends.
Confirm same point as upper ends."
Adjust the CONTRAST when viewed from an angle to play.
Figure 15
Please move a little WHEEL.
Make sure that OK will be displayed next to the ""MIN"" on the LCD like the 15 figure.
Please move WHEEL to near the center.
Make shure that OK will be displayed next to the ""CENTER"" on the LCD like the 15 figure."
Make sure that the OK is displayed on the side that shows the "MAX" of the LCD like the 15 figure
by the time that it stops up the WHEEL.
Where it stops, numbers enclosed in square yellow 15 figure, make sure that it is "00000".
Figure 16
Figure 17
Make sure that it is displayed as of 16 figure where PIANO LED is lit with one round to the right
ENCORDER. (Upper left of that number is +12)
"It is bad the following cases.
When OK is not displayed.
Number ""+"" displayed on the upper left of the LCD is larger than 12, or less, fixed 00."
Please press the [PROG], the value is reset. (Screen is displayed as shown in Figure 16 .)
Make sure that it is displayed as of 16 figure where PIANO LED is lit with one round to the left
ENCORDER. (Upper left of that number is -12)
As well as right turn, please start the next inspection after the test was successful by pressing the
[SW1].
"When it is turned one click to the right ENCODER, to confirm that value at enclosed in yellow at the
top left of the screen shown in Figure counts up.
When Turned one click to the left ENCODER, the number is sure to count down."
With one round to the right ENCODER, make sure that the value of the upper left may appear OK like
a 18 in Figure +21 to +27.
"It is defect the following cases.
When OK is not displayed.
Number ""+"" displayed on the upper left of the LCD is larger than +27, or is less than +21, fixed 00."
Please press the [PROG], the value is reset. (Screen is displayed as shown in Figure 18 .)
With one round to the left ENCODER, make sure that the value of the upper left may appear OK like a
18 in Figure -27 to -21.
"It is defect the following cases.
When OK is not displayed.
Figures displayed on the upper left of the LCD is larger than +27, less than +21, or leave unchanged
00. (Display position is marked with yellow boxes in Figure 18)"
Please press the [PROG], the value is reset. (Screen is displayed as shown in Figure 18 .)
With one round to the left ENCODER, make sure that the value of the upper left may appear OK like a
18 in Figure -27 to -21.
"It is defect the following cases.
When OK is not displayed.
Figures displayed on the upper left of the LCD is larger than -21, less than -27, or leave unchanged 00.
(Display position is marked with yellow boxes in Figure 18)"
Please start the next inspection after the test was successful by pressing the [PROG].
"When it is turned one click to the right ENCODER, to confirm that value at enclosed in yellow at the
top left of the screen shown in Figure counts up.
When Turned one click to the left ENCODER, the number is sure to count down."
With one round to the right ENCODER, make sure that the value of the upper left may appear OK like
a 19 in Figure +21 to +27.
"It is defect the following cases.
When OK is not displayed.
Figures displayed on the upper left of the LCD is larger than +27, less than +21, or leave unchanged
00. (Display position is marked with yellow boxes in Figure 19)"
Please press the [EXIT], the value is reset. (Screen is displayed as shown in Figure 19 .)
With one round to the left ENCODER, make sure that the value of the upper left may appear OK like a
24 in Figure 19 -27 to -21.
Figure 19
Make sure that the OK is displayed.
"It is defect the following cases.
When OK is not displayed.
Figures displayed on the upper left of the LCD is larger than -21, less than -27, or leave unchanged 00.
(Display position is marked with yellow boxes in Figure 19)"
It is defect if value is less than -27 or leave unchanged 00.
Please start the next inspection after the test was successful by pressing the [EXIT].
Figure 20
(Depending on the initial set position of the TEMPO VOLUME, might OK is displayed in the frame of
the side that displays the CENTER of the LCD first.)
After passing through the near the center by turning the TEMPO VOLUME, it appears like a 20
Figure
By the time knob is turned to the left TEMPO VOLUME, you will see something like Figure 20 .
In this way, make sure that the three OK is displayed.
After confirmation, and center the TEMPO VOLUME.
When it comes near the center, the next inspection starts automatically.
Figure 20
7. PEDAL inspection
When you enter the inspection of PEDAL, screen like
Figure 21 is displayed on the LCD.
Figure 21
Figure 22 Figure 23
When you press the PS-1, make sure that it is displayed as shown in Figure 24.
When you release the foot from PS-1, make sure that it is displayed as shown in Figure 25.
Figure 24 Figure 25
As you slowly depress the DS-1H, and make sure it is displayed as shown in Figure 26 and Figure 27
Figure 26 Figure 27
Figure 36
The cut off power without being display of Figure 36 there is a failure.
Next, make sure the power is turned off by pressing the [TAP].
Figure 37
LINE Gain 00
QTY
Part Number Category Part Name Location Reference 61 88
[TOP]LED1-20 LED22-27 LED29
510312511512 Chip LED KPT-1608SURCK-KORG KLM-3189/90/91/92 54 54
LED31-56 LED61
510312512021 LED SLR343BD2TT32 KLM-3189/90/91/92 [TOP]LED21 1 1
510312511513 Chip LED KPT-1608FGCK-KORG KLM-3189/90/91/92 [TOP]LED28 LED57 2 2
510374520027 TACT SW SKRGARD010 KLM-3189/90/91/92 [TOP]SW1-15 SW17-21 SW26-57 52 52
510360520031 ROTARY VR RK12L12C0C0H KLM-3189/90/91/92 [TOP]VR1 1 1
510360520051 VR RK09D1130C80 KLM-3189/90/91/92 [TOP]VR5 1 1
510360525011 ENCODER SWITCHS XRE0125PVB20FINB1-2-24PCE KLM-3189/90/91/92 [TOP]ENC1 ENC3 2 2
510360525012 ENCODER SWITCHS XRE012505PVB20FINA1-2-12PCE KLM-3189/90/91/92 [TOP]ENC2 1 1
510C90793189 CIRCUIT ASS'Y KROSS-61 KLM-3189/90/91/92 KLM-3189/90/91/92 1 1
510474528002 CONNECTOR A2001WV-3P KLM-3189/90/91/92 [TOP]CN3C 1 1
510474528004 CONNECTOR A2001WV-5P KLM-3189/90/91/92 [TOP]CN1B 1 1
510450524509 DC JACK LD-0214 KLM-3189/90/91/92 [TOP]DJ1 1 1
510450524506 PHONE JACK LJE0371-4P KLM-3189/90/91/92 [TOP]PH4-5 2 2
510310511506 SCHOTTKY DIODE RB051L-40TE25 (S) KLM-3189/90/91/92 [BOT]D1 1 1
510374510004 SW PS-22F03 (NON-LOCKED) KLM-3189/90/91/92 [TOP]SW1 1 1
510450521503 PHONE JACK YKB21-5074G (PHONE JACK) (D) KLM-3189/90/91/92 [TOP]PH1-3 PH6-8 6 6
510450521507 DIN JACK YKF51-5074V KLM-3189/90/91/92 [TOP]DIN1 1 1
510C90793193 CIRCUIT ASS'Y KROSS-61 KLM-3193/94/95 KLM-3189/90/91/92 1 1