Professional Documents
Culture Documents
EchoPAC 204 Installation Manual
EchoPAC 204 Installation Manual
0123
Installation Manual
EZ294861-1EN — English
Rev. 02
Operating Documentation
Copyright © 2019, 2020 By General Electric Co.
GE VINGMED ULTRASOUND AS
Strandpromenaden 45
3191 Horten, Norway
Tel.: (+47) 3302 1100 Fax: (+47) 3302 1350
www.gehealthcare.com
Revision History
Reason for change
DATE
REV (YYYY-MM-DD) REASON FOR CHANGE
Please verify that you are using the latest revision of this document. Information
pertaining to this document is maintained on ePDM (GE electronic Product Data
Management). If you need to know the latest revision, contact your distributor, local GE
Sales Representative or in the USA call the GE Ultrasound Clinical Answer Center at
1 800 682 5327 or 1 262 524 5698.
Table of Contents
Chapter 1 — Introduction
EchoPAC Software Only installation manual
Product description
Safety
Chapter 2 — Software installation
EchoPAC Software Only content
Computer requirements
Install EchoPAC Software Only for the first time
Preliminary recommendations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-4
Start Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-5
License agreement and ReadMe file- - - - - - - - - - - - - - - - - - - - - - - - - - 2-8
Preparing the archive installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-9
Defining the archive location - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-10
EchoPAC Share - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-12
System check- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-13
Copying files - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-14
Insert Dongle and complete installation- - - - - - - - - - - - - - - - - - - - - - - 2-15
Note regarding the use of removable media - - - - - - - - - - - - - - - - - - - 2-16
Upgrade existing EchoPAC Software Only installation
Preliminary Recommendations- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-17
Start Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-18
Uninstallation of existing software- - - - - - - - - - - - - - - - - - - - - - - - - - - 2-19
Restarting Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-21
License Agreement and ReadMe File - - - - - - - - - - - - - - - - - - - - - - - - 2-22
Preparing Archive Location - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-23
Defining Archive Location - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-25
EchoPAC Share - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-26
System Check - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-27
Copying files - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-27
Resuming Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-28
Starting EchoPAC Software Only
Starting EchoPAC Software Only - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-31
Accessing user documentation- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-31
Restore archive and Configuration backup after upgrade - - - - - - - - - - 2-32
Introduction
Product description
Safety
1. Patient environment
Software installation
Computer requirements
Preliminary recommendations
If you are installing EchoPAC Software Only on a domain
(please contact your network administrator if you are unsure of
the meaning of this):
1. Start up the PC without logging on to the domain, i.e. as a
local user only.
2. Install EchoPAC Software Only.
3. Start up the PC again and log on to the domain.
It is recommended to keep Windows default settings for text size
(100%, 96 dpi) for optimal display in EchoPAC Software Only.
Administrator user is required for installation and for
configuration of server-related remote archive/DICOM
dataflows.
NOTE: Running EchoPAC Software Only via Remote Desktop is not
supported.
NOTE: Running EchoPAC Software Only on Virtual Machine is not
supported.
Start Installation
Continue installation
1. Press Install.
The EchoPAC Software Only Installation wizard is started
and the Welcome screen is displayed (Figure 2-3).
2. Press Next.
1. Press Next.
The ReadMe text is displayed (Figure 2-5).
EchoPAC Share
The EchoPAC Share is needed if a Vivid scanner is configured
to store to the EchoPAC, where the EchoPAC is the remote
archive. If Share is not enabled, the EchoPAC will not be
available for connection. The Vivid scanners will not be able to
see the EchoPAC database service, checkout will fail, and
transfer will not work. If ‘No’ is selected, network based data
transfers can only be initiated from the EchoPAC itself. Media
transfer will still be available.
If this EchoPAC is to be used as an EchoPAC Share, select YES
in the dialog below. If not, select NO.
System check
The System information window is displayed (Figure 2-10)
1. Press Next.
The installation proceeds to copying files(Figure 2-12). But if
some of the items displayed in the System information
window are not fulfilling the system requirements/
recommendations the following error message is displayed.
This results in aborted installation.
Copying files
The Start copying files window is displayed (Figure 2-12).
1. Press Next.
The EchoPAC Software Only and database files are copied
on the computer.
2. Press Finish.
NOTE: Refer to ‘Starting EchoPAC Software Only’ on page 2-31 when
starting up EchoPAC Software Only for first time.
Preliminary Recommendations
If you are installing EchoPAC Software Only on a domain
(please contact your network administrator if you are unsure of
the meaning of this):
• Start up the PC without logging on to the domain, i.e. as a
local user only.
• Install EchoPAC Software Only.
• Start the PC again and log on to the domain.
It is recommended to keep Windows default settings for text size
(100%, 96 dpi) for optimal display in EchoPAC Software Only.
It is recommended to perform backup of Patient Archive and
System Configuration before upgrading EchoPAC Software
Only.
Administrator user rights are required for installation and for
configuration of server-related remote archive/DICOM
dataflows.
Start Installation
2. Press OK.
InstallSheild Wizard starts uninstallation of EchoPAC
Software Only.
3. Click Finish.
Restarting Installation
Restart installation from the media. The EchoPAC Software Only
InstallShield Wizard starts (Figure 2-20) and the Welcome
Screen is displayed (Figure 2-21).
Press Next.
1. Press Next.
The ReadMe text is displayed. (Figure 2-23)
2. Select:
EchoPAC Share
The EchoPAC Share is needed if a Vivid scanner is configured
to store to the EchoPAC, where the EchoPAC is the remote
archive. If Share is not enabled, the EchoPAC will not be
available for connection. The Vivid scanners will not be able to
see the EchoPAC database service, checkout will fail, and
transfer will not work. If ‘No’ is selected, network based data
transfers can only be initiated from the EchoPAC itself. Media
transfer will still be available.
If EchoPAC Software Only is to be used as an EchoPAC Share,
select YES in the dialog box below. If not, select NO.
System Check
Copying files
The Start Copying files window is displayed (Figure 2-31).
1. Press Next.
The EchoPAC Software Only and database files are copied to
the computer.
Resuming Installation
Once files are copied, the EchoPAC Software Only installation is
resumed.
1. Select either:
• Yes, to permanently delete the archive from the
previous installation.
or
• No, to keep the archive on the disk.
The Insert Dongle window is displayed. (Figure 2-35)
3. Press Finish.
NOTE: Refer to ‘Starting EchoPAC Software Only’ on page 2-31 when
starting EchoPAC Software Only for first time.
NOTE: Refer to ‘Restore archive and Configuration backup after
upgrade’ on page 2-32 for troubleshooting.
On line Help
Electronic documentation
If the EchoPAC Software Only User Manual is provided on a
media, follow the following procedure:
1. Insert the media in the computer.
2. Open the media drive on your desktop.
3. Double click on the gedocumentation.html document.
4. In the Documentation interface home page select the
EchoPAC Software Only user manual.
Local Archive shared doesn’t work with error message ‘Unidentifed problem
occured, please generate a log file’
Local Archive shared doesn’t work with Error ‘No network connection, wrong
passord’
Software validation
Introduction
Validation Procedure
Preliminary checks:
Software installation
Validation procedure
Validation form
Please fill in as much information as you have available. As a help to find the PC specific information (item 9.
to 17. in the table below), you can look inside the file “EP_Install_<date>.log”, which is located in the folder
named “Log” inside the folder you specified as archive destination during installation. In fact, we
recommend, if possible, that you print out that file and attach it to the validation form.
1 Name
2 Institution
3 ZIP/City
4 Country
5 E-Mail address
7 Dongle-ID
(see USB hardware key)
8 Type of PC
(Laptop, Desktop, Tablet...etc.)
10 Operating System
11 Boot drive
12 Processor speed
13 Memory (RAM)
14 Number of colors
15 Screen resolution
16 Free space on C:
18 USB drive
19 OS language
Passed
Failed
Step
Description
2 Image quality
Successful installation
Date:
Name (print):
Signature:
Image samples
The images at the end of the book are used for Image quality
validation of EchoPAC Software Only installed on your PC.