Professional Documents
Culture Documents
KSLV 1
KSLV 1
or KSLV, is South Korea's first carrier rocket, which made its maiden
flight on 25 August 2009. It is built by KARI, the national space agency
of South Korea along with Korean Air and Khrunichev State Research
and Production Space Center (Russia) provided first stage and was
launched into space from the country's new spaceport,
the Naro Space Center. The official name of the first KSLV rocket,
KSLV-I is Naro, which is the name of the region in which Naro Space
Center is located.
The KSLV-I launch vehicle is based on the first stage of the Russian
Angara rocket combined with a solid-fueled second stage built
by South Korea. This configuration is reportedly capable of launching
a satellite weighing 100 kilograms into low elliptic orbit.
(from http://en.wikipedia.org/wiki/Naro-1)
H ~ 350 mm
Paper used:
0,26 mm - 200 gr ("cardstock")
0,15 mm - 130 gr
Glue: PVA
© 2010 Designed by L.Cherkashyn This cardmodel is only for personal and not for commercial use
F2
A2 F3a F3
F3
connector
F2
for F3
F1 F3e F3
F3d F3
white ball
d = 3,5 mm A1b
connector connector
for F2 for A2 A1a
A2
A1a A1
A3a A3
A3
A1
A2b A2b A2c
first glue top of A2c on A1
A2c then glue bottom of A2c on A2
A3b B3b
B2b
B2d
A3d
A3c
F3b
connector for A3
A4a
F3c
A4d A2a
A3e A3
A4
Page 2 print on cardstock © 2010 Designed by L.Cherkashyn This cardmodel is only for personal and not for commercial use
slots
A4
A4g
A4g
P2
P2
A4f
A4f
A4f
A4f
A4f
A4f
A4f
A4f
connector
P1
A4b
for A4
P3
P3
A4h
A4h
A4c A4
A3f A4h
A4e A4e-1
A4e-1
slots
A4f glue onto cardstock
for A4h-1
A4h-1
spare
Page 3 print on cardstock © 2010 Designed by L.Cherkashyn This cardmodel is only for personal and not for commercial use
B1
B2a B2
B1
B3a B2
B3
A3c
cuts for B2c connector
B2 for B2
P2 B3
B4
A4b
N1 connector
N1 / N2
N2
P3
nozzle
insertion
N2
P3
A2b A4g
Page 4 print on fine paper © 2010 Designed by L.Cherkashyn This cardmodel is only for personal and not for commercial use
F1
F2
Interstage
1 - glue cone A2
2 - glue cylinder A1 by strip A1a
then glue cylinder A1b into A1a
3 - assembly these with cone A2
and glue A2a
__________________________
A3d
A3e A4g
P2
A4a
Oxidizer pipe
A4f
1 - glue P3 onto A4
A4b A4 2 - glue tube P1
3 - glue P1 into P3
P1
4 - glue P2
P3
A4h
A4c
A4d A4h-1
1 mm
nozzle A4e
insertion N1
N2
Page 5 © 2010 Designed by L.Cherkashyn This cardmodel is only for personal and not for commercial use