Professional Documents
Culture Documents
Screenshot 2024-02-15 at 06.55.31
Screenshot 2024-02-15 at 06.55.31
WELL: JAS-13
REV.1
12-Februari-2024
Prepared for
Bapak Adit Ardianto
PT Pertamina EP Zone 7 Area 1
Prepared by
Adham P
PT BBP Jakarta
1
PT. Bukitapit Bumi Persada
Content
1. Summary 3
2. Well Data 4
3. Well Profile 5
4. Treatment Calculation 6
5. Job Procedure 7
6. Estimation Cost 8
2
PT. Bukitapit Bumi Persada
1. Summary
Based on well history data, JAS-13 has been opened in BRF Layer “2628 – 2632
m” which is Sandstone Reservoir as Oil Well status.
Acidizing using 15% acid was selected as stimulation method at JAS-13 based
on indication damage. This proposal Acidizing treatment design using 100
GPF, so that damage can be removed in 3.8 ft radial penetration from the
wellbore.
In order to optimize an excellent acid placement for this treatment, BBP will
use Coiled Tubing to convey treating fluid. Coiled Tubing will also nitrify the
acid so it can be flow back easily to the surface. Tubing pickle will be
performed to clean any solid or rust prior to inject fluid to the formation.
AUTHORIZATION
3
PT. Bukitapit Bumi Persada
2. Well Data
Wellbore Data
Total Depth : 3190 m
Casing
4
PT. Bukitapit Bumi Persada
3. Well Profile
5
PT. Bukitapit Bumi Persada
4. Treatment Calculation
I. WELL DATA :
TOTAL DEPTH 2,794.0 METER
PREV. CASING 9 5/8 INCH 43.5 LB/FT 8.755 INCH I.D 2,794.0 METER
EXIST. CASING INCH LB/FT INCH I.D METER
EXIST. CASING INCH LB/FT INCH I.D METER
D.P/TUBING 2 7/8 INCH 6 LB/FT 2.441 INCH I.D 2,600.0 METER
COIL TUBING 1 1/2 INCH 1.210 LB/FT 1.210 IN I.D 3,200.0 M TMD
9-5/8" PACKER 2,590.00 METER
V. TREATMENT SYSTEM
210.0 GALL Pre Flush
CONCENTRATION TOTAL
WATER 945.0 GPT 198.0 GALL
NACL 215.0 PTG 45.0 LBS
BMS-50 50.0 GPT 11.0 GALL
BSU-12N 5.0 GPT 1.1 GALL
6
PT. Bukitapit Bumi Persada
TREATMENT SUMMARY
7
PT. Bukitapit Bumi Persada
5. Job Procedure
1. Conduct Pre-job safety meeting, fill and discuss Work Permit and JSA.
2. Perform Slick Line Gauge Cutter to ensure hole clearence.
3. Set the Pumping Unit, CTU, Batch Mixer and Mixing Tank.
4. Set Bleed off tank in safe distance min 100 ft from well.
5. Conduct CTU test as follow.
a. Perform CT BOP Test, close the blind ram, test equalizing port and test
equalizing port and test the blind ram to 3500 psi for 5 minutes. Bleed off
pressure.
b. Spot the injector head and stab the CT. Make up BHA with 360 degree
Nozzle.
c. Pull tools into stuffing box and apply 5000 lbs. To check weight indicator
and the tool connection.
d. RU CT injector onto the CT's BOP.
e. Run the CT onto the CT BOP’s pipe ram.
f. Close the pipe ram of CT's BOP. Test the CT at maximum pressure of 3500
psi.
g. Test stripper. Close stripper, open pipe ram equalizing port, increase
pressure if required to test the stripper pack off system.
h. Bleed off pressure from flow tee to zero. Calibrate the depth.
6. Once CT has been tested, equalize pressure across swab valve. Open well and
begin run into well.
7. RIH CT slowly to top perfo 2628 m (40-80 ft/minute) with pumping idle
pumping 2% Kcl, always watches the weight indicator, and perform pull test
every 500 ft.
Acid Step
8. Perform Injectivity Rate Test, 0.5 bpm, 1 bpm and 1.5 bpm, record rate and
pressure (Max Frac PWH Press 2200 psi).
8
PT. Bukitapit Bumi Persada
13. Displace with 42000 scf N2 / 2% Kcl depend on formation respon.
a. If Pwh drop drop use N2
b. If Pwh more flat during pumping use 2% kcl
14. Open CT and Tubing annulus, flow back spent acid to ground pit until PH 6-7.
15. POOH CT to surface
16. Flushing with water + soda ash, Rig Down CTU, Job Completed
9
PT. Bukitapit Bumi Persada
6. Cost Estimation
Material Cost
35 Corrosion Inhibitor Gall 450,000.00 15,750,000.00
66 Corrosion Inhibitor Aid For CTU Gall 158,500.00 10,461,000.00
66 Iron Control Additive Lbs 18,000.00 1,188,000.00
14 Nonionic Surfactant Gall 195,000.00 1,365,000.00
88 Mutual Solvent Gall 200,000.00 17,600,000.00
33 Scalin-1 Gall 225,000.00 7,425,000.00
Pertamina 569 HCL 32% Raw Acid Gall 0.00
Pertamina 948 Nacl Lbs 0.00
Pertamina 550 Soda Ash Lbs 0.00
4000 Liquid Nitrogen Gall 25,000.00 100,000,000.00
10
PT. Bukitapit Bumi Persada
Lab Test
Page 1 of 1
FORM
Code no. FRM-LAB-04
Revision no. 2
LABORATORY STIMULATION REPORT
Issued 30-Jul-18
TEST PROCEDURES :
1. Weight ± 3 grams dried sample.
2. Put sample into 5 ml xylene in erlenmeyer and put into oven until dry.
3. Weight again the dried sample.
4. Put sample into 100 ml the Preflush fluid system in test bottle.
5. Put the test bottle in water bath at BHST for 1 hour.
6. Filter the sample with weighted filter paper.
7. The filter paper into oven at 105 deg C for 1 hour and after that the filter paper into desicator to make it cool.
9. Weight the filter paper (with dried sample).
10. The sample is then calculated as percent by weight of original weight.
Formulation Composition :
Preflush Acid 15%
Water 480 gpt
BIC-30 20 pptg
HCl 470 gpt
BCI-01 25 gpt
BMS-50 25 gpt
TEST RESULTS :
NOTICE : This report is property of PT. Bukitapit Bumi Persada. Any user of the report agrees that PT. Bukitapit Bumi Persada shall not liable for any losses or damages
which result from the use of the information in the report. PT. Bukitapit Bumi Persada makes no warranties in respect to the information in the report whether expressed or
implied of fitness for a particular purpose.
11
PT. Bukitapit Bumi Persada
Software calculation
1. TFA (Tubing Force Analysis)
12
PT. Bukitapit Bumi Persada
13
PT. Bukitapit Bumi Persada
14
PT. Bukitapit Bumi Persada
15
PT. Bukitapit Bumi Persada
16
PT. Bukitapit Bumi Persada
ACID SOFTWARE CALC
17
PT. Bukitapit Bumi Persada
18
PT. Bukitapit Bumi Persada
2. BHA Config
19
PT. Bukitapit Bumi Persada
3. PCE Config
20
PT. Bukitapit Bumi Persada
4. Job Layout
Tangki Ablasan
20 meter
30 meter
21
PT. Bukitapit Bumi Persada