Professional Documents
Culture Documents
Power Plant Mount
Power Plant Mount
Power Plant Mount
POWER PLANT
MOUNT
CONTENTS
GENERAL INFORMATION
Inertia principal axes system is incorporated into Upper installation of roll mount reduces engine
the engine mount system. rolling, and increase of insulator bore also reduces
idle vibration.
CONSTRUCTION DIAGRAM
<Engine mount, Transmission mount>
Engine mount
Transmission mount
Crossmember
Front roll mount bracket
Crossmember bar
Centermember
POWER PLANT MOUNT - General Information/Special Tool 32-3
<Engine roll stopper, Centermember, Crossmember: R.H. drive vehicles>
Crossmember
Crossmember bar
Centermember
SPECIAL TOOL
Tool Number Name Use
MB990635, Steering linkage Tie rod end disconnection
MB991113 or puller
MB991406
32-4 POWER PLANT MOUNT - Engine Mounting
ENGINE MOUNTING
REMOVAL AND INSTALLATION
Caution
*: Indicates parts which should be initially tightened, and then fully tightened after placing the
vehicle horizontally and loading the full weight of the engine on the vehicle body.
12 ± 2 N·m
67 ± 7 N·m *
98 ± 10 N·m *
4 3
Removal steps
1. Power steering pressure hose as- 3. Engine mounting bracket
sembly "AA 4. Engine mounting insulator
2. Engine mounting connecting bolt
3
2
47 ± 7 N·m *
82 ± 7 N·m *
Removal steps
1. Transmission mounting connecting 2. Transmission mounting
bolt "AA 3. Transmission mounting stopper
INSPECTION
Check the transmission mounting insulator for cracks,
separation or deformation.
32-6 POWER PLANT MOUNT - Engine Roll Stopper, Centermember
52 ± 7 N·m *
6 35 ± 5 N·m *
8
7
70 ± 10 N·m
52 ± 7 N·m *
5
52 ± 7 N·m *
2
35 ± 5 N·m *
1
4
69 ± 10 N·m
3
49 ± 10 N·m
69 ± 10 N·m
49 ± 10 N·m
Front roll stopper and centermember Rear roll rod removal steps
removal steps 6. Rear roll rod connecting bolt
1. Crossmember bar 7. Rear roll mount bracket
2. Front roll stopper connecting bolt 8. Rear roll rod connecting bolt
3. Centermember 9. Rear roll rod bracket
"AA 4. Front roll stopper 10. Rear roll rod assembly
5. Front roll mount bracket
POWER PLANT MOUNT - Engine Roll Stopper, Centermember 32-7
<R.H. drive vehicles> 70 ± 10 N·m 8
6 35 ± 5 N·m *
7
70 ± 10 N·m 52 ± 7 N·m *
5
2
35 ± 5 N·m * 52 ± 7 N·m *
4
1
69 ± 10 N·m
49 ± 10 N·m
69 ± 10 N·m
49 ± 10 N·m
Front roll stopper and centermember Rear roll stopper removal steps
removal steps 6. Rear roll stopper connecting bolt
1. Crossmember bar 7. Rear roll mount bracket
2. Front roll stopper connecting bolt 8. Rear roll stopper
3. Centermember
"AA 4. Front roll stopper
5. Front roll mount bracket
Front of vehicle
32-8 POWER PLANT MOUNT - Crossmember
CROSSMEMBER
REMOVAL AND INSTALLATION
Caution
1. Before removing the steering wheel and air bag module assembly, always refer to GROUP
52B - Service Precautions, Air bag Module and Clock Spring. Also, set the front wheels so
that they are facing straight forward, and remove the ignition key. If you fail to do this, the
SRS clock spring will be damaged, causing the SRS air bag to be inoperative and serious
injury.
2. *1: Indicates parts which should be initially tightened, and then fully tightened after placing
the vehicle horizontally and loading the full weight of the engine on the vehicle body.
3. *2: Indicates parts which should be temporarily tightened, and then fully tightened with the
vehicle on the ground in the unladen condition.
Caution
If the vehicle is equipped the Brembo disc brake, during maintenance, take care not to contact
the parts or tools to the caliper because the paint of caliper will be scratched.
4
8
70 ± 10 N·m 18 ± 2 N·m
10
12 57 ± 7 N·m
11 15 ± 3 N·m
13
7
35 ± 5 N·m*1
5
25 ± 4 N·m
9
21 ± 4 N·m
52 ± 7 N·m*1 21 ± 4 N·m
108 ± 10 N·m
6
2
39 ± 5 N·m
3
1
186 ± 10 N·m*2
39 ± 5 N·m
49 ± 10 N·m
167 ± 9 N·m
Removal steps
1. Lower arm and knuckle connection 7. Return hose and return pipe
2. Stabilizer link 8. Pressure hose connection
AA" 3. Lower arm assembly AB" 9. Tie rod end and knuckle connec-
4. Steering shaft assembly and gear tion
box connecting bolt AC" 10. Crossmember assembly
5. Rear roll stopper connection bolt "AA 11. Stabilizer bar
6. Rear roll rod assembly and rear 12. Steering gear and linkage
roll rod bracket 13. Crossmember
32-10 POWER PLANT MOUNT - Crossmember
18 ± 2 N·m
5
6
15 ± 3 N·m
69 ± 9 N·m
4
57 ± 7 N·m
35 ± 5 N·m*1
9
25 ± 4 N·m
8 11 12 7
10 13
21 ± 4 N·m
21 ± 4 N·m
39 ± 5 N·m
3
1
186 ± 10 N·m*2
39 ± 5 N·m
167 ± 9 N·m 49 ± 10 N·m
Removal steps
1. Lower arm and knuckle connection 8. Rear roll stopper connection bolt
2. Stabilizer link AC" 9. Crossmember assembly
AA" 3. Lower arm assembly 10. Rear roll stopper
4. Pressure hose connection "AA 11. Stabilizer bar
5. Return hose connection 12. Steering gear and linkage
6. Steering shaft assembly and gear 13. Crossmember
box connecting bolt
AB" 7. Tie rod end and knuckle connec-
tion
POWER PLANT MOUNT - Crossmember 32-11
Mounting bolt
Transmission jack
Nut
Transmission
jack
Bushing Fixture
INSPECTION
D Check the crossmember for cracks and damage.
NOTES