Professional Documents
Culture Documents
ARCHITECTURAL
ARCHITECTURAL
SPECIFICATIONS
PROPOSED CENTER OF
EXCELLENCE AND ASSESSMENT
CENTER
MIST Compound, Brgy. Sta. Elena, Marikina City
PREPARED FOR:
A. The Scope of Work covered within this Specification is the complete construction
of the PROPOSED CENTER OF EXCELLENCE AND ASSESSMENT
CENTER.
B. This section is prepared in a concise manner, the intention of which is to save
time and effort in locating important contents within these Specifications.
C. The Executions of this Sections shall be coordinated and correlated to each
corresponding elaborated section of these same Specifications.
D. In case discrepancies exist between this section and its corresponding elaborated
sections, notifies the Architect immediately for clarification: his decision shall be
final.
E. The contractor shall bear the responsibility to check all the numbers and units as
may be indicated on the Specifications. It is understood that the Contractor shall
supply and install the actual required units as approved on the Plans.
F. Substitutions of materials or equipment of makes other than those specified in the
contract documents will be approved by the Architect for the following reasons
only:
1.04: SITEWORK:
- One (1) part escombro, two parts lastillasfor all filling jobs
done in layers not exceeding 150 mm thick, 95% compaction,
up to the elevations as per Plans.
- 100 mm thick gravel fill, thoroughly tamped for slabs and
footing resting on ground or earthfill.
b. REINFORCEMENT MATERIALS:
B. TERMINATE CONTROL:
1. Chemical to be used:
a. Water-based chemicals
a. Soil poisoning work shall begin after all preparations for slab
placement have been completed.
b. Soil poison shall be applied only when soil is not excessively wet.
c. After grading and leveling the soil in the ground and layers of
gravel laid preparatory to the pouring of concrete, flood or soak
every square meter of floor area with soil poison working solution.
e. Two gallons of soil poison working solution are applied per five
(5) lineal feet and shall be applied to all areas that era penetrated
by pipes, ducts and other construction features.
f. Hollow masonry walls resting on grades have its voids treated with
one gallon of soil poison working solution per five (5) lineal feet of
walls. Poison is poured directly into the hollow masonry.
4. MATERIALS:
2. All CONCRETE HOLLOW BLOCKS shall extend up to the bottom of the beam
or slab.
b. LINTEL BEAMS: thickness varies per concrete hollow block wall x 350
mm reinforced with 2-12 mm diameter continuous bar ( top and bottom)
with 10 mm dia. stirrups, 4 at 100 mm; rest at 250 mm on center.
B. INTEGRAL WATERPROOFING
6. See Roofing Framing Plan for rafter, purlin spacings, roof sheet
fastening and other details.
1.08: METALS
A. STRUCUTRAL STEEL
B. METAL FABRICATION
c. HANDRAIL 50 mm Ø BI gage 20
1.09 WOOD
1. TANGUILE: kiln dried, for stair handrail. Tanguile jambs and headers
for all doors and accordion type wood partition.
2. TANGUILE PLYWOOD;
6. ALL WOODS shall be of good quality and free from any defects.
A. WOOD DOORS:
1. HOLLOW CORE FLUSH DOORS:
1. STEEL WINDOWS:
2. STEEL DOOR
b. See detail
C. FINISHING HARDWARES:
The following Hardware sets are furnished for whatever assistance it may
afford the Contractor. Verify Plans, Specifications on hardware quality
required. Should any particular item be omitted, provide such door or item
hardware same as required for similar purposes.
3. MISCELLANEOUS HARDWARE:
All other necessary hardware such as latch bolts, catch locks, chain
door fasteners, door stops, wall stops and holders, push plates, handles,
etc. shall be type ,size and design suitable for the purpose or as
approved by the Architect.
D. GLASS GLAZING
4. SCHEDULE:
1.10: FINISHES
A. FLOOR FINISHES:
B. WALL FINISHES:
C. CEILING FINISHES:
1. RUBBED CONCRETE FINISH: for all exposed beams and slabs,
painted finish, not otherwise noted with other finishes.
2. FICEMBOARD CEILING: 6 mm thick, FICEM BOARD on
50mm x 50mm KD Rough Tanguile wood nailer and hangers;
closed joints with/ without v-cut grooves as indicated on plans.
3. PRISMATIC LIGHT DIFFUSERS: 3mm thick,
PRISMALENS/MOLDEX
4. WOOD MOULDING: quarter c1”
GENERAL:
1.11: MISCELLANEOUS:
B. APPLICATION: all applications and methods used shall strictly follow the
Manufacturer’s Instructions and Specifications.
C. SURFACE TREATMENT: all surfaces including masonry wall shall se
thoroughly cleaned, puttied (masilla), sandpapered, rubbed and polished;
masonry wall shall be treated with Neutralizer.