Professional Documents
Culture Documents
Eastman Industries - Boq
Eastman Industries - Boq
Eastman Industries - Boq
BILL OF QUANTITY
1. HVLS Fans
3. Inline Fans
Supply, installation, testing and commissioning of variable refrigerant volume Please Note all offices cabins
modular type airconditioning system complete with indoor, outdoor unit should be are low height instead of full
aircooled 100% invertor technology base microprocessor controlled VRV/ VRF ceiling height.
system using R410A/R407 refrigerant. The system shall be capable of performing And Consider the VRV at
both cooling as well as heating function suitable for operation on 415+/- 10%- volts, Ground Floor Reception and
50 Hz. 3 Ph AC supply and shall be comprise of rotary/scroll compressor and Quality Room
aircooled condenser, fan with motor the system comprising,MS stand, vibration
isolation pads, as required. The COP level not less than 4.0 at 100% capacity. With
individual controller, indoor unit shall be comprising of cooling coil, blower with multi
speed motor electronic expansion valve, full system gas and oil charged,MS stand
for ODU with properly painted,as per detail given in specifications and having
following items :
Outdoor Unit
a) 20HP No. 1
b) 16HP No. 1
b) Indoor Units
c) Refnet Joints
f) SITC of Main centrallised controller for all IDU & ODU with BMS compitable on open
No. RO
protocol.( As per BMS at site)
5. Refrigerant Piping
6. Drain Piping
Supply & fixing of UPVC drain piping with all fitting such as bends, tees etc.
necessary clamps, adequate support duly insulate with 6 mm nitrile rubber insulation
complete as per specifications, requirement, standardard and drawings.
6.1 50 mm dia Rm 20
6.2 40 mm dia Rm 15
6.3 32 mm dia Rm 40
6.4 25 mm dia Rm 50
7. Ducting
8. Grilles / Diffuser
8.1 Supply, installation, testing and commissioning of Aluminium extruted powder coated
supply and return air grilles with dampers as per specifications and drawings
(Approval of colour shall be taken from Architects/ Consultants).
Sqm 1.0
Page 4 Eastman Industries- Boq
Sqm 2.0
8.3 Supplying, fixing testing commissioning of Return air diffusers of powder coated
aluminium without volume control dampers with anti smudge ring & removable core.
(Approval of colour shall be taken from Architects/ Consultants).
Sqm 1.0
8.4 Supplying, fixing testing commissioning of Return air grilles of powder coated
aluminium and without dampers (Approval of colour shall be taken from Architects/
Consultants). Sqm 1.0
9. Power Cabling
Supply and installation of XLPE FRLS, cores laid up, tape inner sheathed, armoured
copper cables for various equipments along with cable terminations lugs, glands,
tagging etc. through walls/ceiling with appropriate clamps & fixing arrangement for
running on cable tray, as per specifications and drawings. Flexible support system
as per approval.Support system shall be as per typical support drwaings.
9.1 4C - 10 sqmm Rm 30
Supply and installation of Perforated Cable Tray: Design manufacture, supply and
fixing in position the G.I. cable trays of the following sizes for supporting armoured /
unarmoured aluminium /copper conductor cables. Fabricate the perforated type
cable trays from MS Sheet with 1.6 mm/1.2 mm thick. The steel should be complete
as required. (the horizontal and vertical bends, T's should be factory fabricated and
the rate should include for the same) for following services. Measurement shall be
done along centre line of cable tray.Flexible/Rigid support system as per
approval.Support system shall be as per typical support drawings.
The perforated cable trays shall be hot dip galvanized according to IS-2629, BS729-
1971 or equivalent standard suitable for indoor/outdoor use having moderate
humidity and air pollution. The zinc coating thickness shall work out by applying a
610 gm of zinc per square meter surface with an approximate thickness of 80
microns.
Page 5 Eastman Industries- Boq
11. Isolators
Supply & fixing of following rating weather proof IP-65 endosure isolators with
suiatble size copper cable from isolator to ODU all accessories as required for
following as per specifications, standards & requirement.
12. Earthing
Supply and laying of double earthing continuity conductors of G.I. /G.S.S between
panel boards and equipments as drawings.
12.1 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as
required. Rm 40
Page 6 Eastman Industries- Boq
Supply, installation, testing and commissioning of wall mounted industrial fans with
adjustable height, oscillation, front & rear protection grille, blades, motor, mounting
accessories for wall as well as for steel coloum, ON/OFF switch etc. all required
/necessary accessories for proper working. Kindly Consider the Plastic
Wall Mounted Fan in GF
Reception / First Floor Office
areas / 2nd Floor Office areas/
All Conference rooms/All
13.1 600 mm dia (Sweep) 1440 rpm (Max.) Nos. 30 Quality Rooms.
Total Rs.