Professional Documents
Culture Documents
RWTP GB CNS Msa 000168 00
RWTP GB CNS Msa 000168 00
7 Product testing/documents
8 Material datasheet NA
9 Safety datasheet NA
10 Technical datasheet NA
11 Product specification NA
12 Product drawings NA
Checked by : Reviewed by :
WATER STOP
(CORKJOINT (MALAYSIA) SDN BHD)
Reference No : RWTP-GB-CNS-MSA-000168
Revision : 00
RWTP-GB-C&S-MSA-000168-00
RASAU INTAKE AND PUMP STATION
INTAKE PLANT
CONTENT
RWTP-GB-C&S-MSA-000168-00
SURE-STOP® PVC WATERSTOP
STANDARD PROFILES
STANDARD PERFORMANCE SPECIFICATION (SPS) GRADE
PRODUCT DESCRIPTION
CORKJOINT Sure-Stop® PVC Waterstops lead the way in high technology
waterstops and comply with international standards.
Sure-Stop® PVC Waterstops are available in rolls with separate intersections supplied to simplify and minimise
on-site fabrication. The waterstop is heat weldable and allows for fast and easy on-site welding/joining.
The efficiency of any waterstop is very dependent on good workmanship, installation, and on full compaction
of the surrounding concrete around the waterstop during concrete placement. Optimum performance will be
achieved if the waterstop is installed by keeping these important factors in mind.
ADVANTAGES
A full range of profiles and sizes to suit all types of construction requirements
Sure-Stop® PVC Waterstops conform to, and exceed all major international standards
High quality compounded PVC for long term durability and integrity
Factory made intersections to simplify and minimise on-site fabrication
On-site welding equipment is available upon request
Internal profiles come with factory pre-punched eyelets for easy and secure wire tying to
reinforcement
Ability to withstand high hydrostatic head pressures
AREAS OF APPLICATION
Water retaining structures: Water excluding structures:
Water tanks Basements
Water treatment plants Underground car parks
Sewage treatment plants Tunnels
Swimming pools Retaining walls
Dams and spillways Suspended slabs
Reservoirs Below ground slabs
Bund walls Roof & podium slabs
Note : The product’s design and performance, its intended use, installation and final confirmation and approval for
use, must be provided by the project’s Design Engineer and Project Manager.
1st Pour Joint Sealant 2nd Pour 1st Pour 2nd Pour
TECHNICAL FEATURES
COLOUR Orange
PACKAGING 150mm - 200mm = 20m roll, 250mm = 15m roll,
320mm = 12m roll
ROLL WEIGHT Dependent upon profile type
STORAGE CONDITIONS & SHELF LIFE 5 years from the date of production if stored
properly in original, unopened and undamaged
sealed packaging, in dry conditions out of direct
sunlight at temperatures between +10°C and +40°C
MATERIAL TYPE Polyvinyl Chloride (PVC)
WELDING TEMPERATURES Approximately 190°C - 200°C
SERVICE TEMPERATURE RANGE -25°C to +70°C
PHYSICAL PROPERTIES
PROPERTY TEST METHOD REQUIREMENT RESULT
Tensile Strength (N/mm2) BS 2782:320A Min. 12.00 15.24
Elongation At Break (%) BS 2782:320A Min. 300 340
Loss of Mass Test (mg/cm2) BS EN 60811-3-2:1995 N/A 1.78
Water Absorption at 23°C (%) ISO 62 Max. 0.15 0.10
Specific Gravity (g/cm3) BS 2782:620B 1.38 ± 0.03 1.41
Thermal Stability
BS 2782:130A N/A 50
Congo Red Test at 180°C, Min.
Hardness, Shore A BS 2782:365B 75 ± 5 SHORE A 76 SHORE A
(BSS 43 ± 9) (BSS 41)
Note : Refer to Corkjoint’s in house Certificate of Analysis (COA) dated 31/12/2022 for test results pertaining to the
above. A COA is conducted on every batch of raw material that is used in the production of Sure-Stop® PVC
waterstops. Independent laboratory test results are also available upon request. Project specific material
properties can be custom compounded to suit. Material properties can vary between batches.
INTERNAL PROFILES
FOR EXPANSION JOINTS FOR CONSTRUCTION JOINTS
15.00 20.00 40.00 15.00 20.00 40.00
150.00 150.00
200.00 200.00
250.00 250.00
320.00 320.00
EXTERNAL PROFILES
FOR EXPANSION JOINTS FOR CONSTRUCTION JOINTS
15.00 60.00 15.00 60.00
3.00
17.00 17.00 17.00
150.00 150.00
200.00 200.00
250.00 250.00
20.00
16.00 16.00
5.00 20.00 20.00
20.00
320.00 320.00
SITE JOINING
CORKJOINT recommends the use of its specialised welding equipment for on-site welding which consists of
thermostatically-controlled Welding Irons and special Welding Jigs (each type of CORKJOINT Sure-Stop® PVC
Waterstop requires its own welding jig to suit the particular shape). On-site joining is a simple exercise using
CORKJOINT Heat Welding Equipment comprising of an adjustable Welding Jig and Welding Iron. The ends of
the waterstop are cut square and placed into the adjustable Welding Jig, then push the ends of the waterstop
against the Welding Iron and bring the two ends together until the molten ends of the PVC fuse. When
ordering Welding Equipment, please advise profile number of the waterstop required.
WRITTEN SPECIFICATION
Where shown on the drawings waterstops shall be Sure-Stop® PVC Waterstop (state profile number required)
as supplied by CORKJOINT. Provide factory made waterstop fabrications for all changes of direction,
intersections and transitions, leaving only straight butt joined splices for on-site fabrication.
The information and the recommendations relating to the application and end use of this product are given in
good faith and are based on the information provided by the manufacturer of the product and/or the
Company’s current knowledge and experience in connection with the product when properly stored, handled
and applied under normal conditions and no liability of final function at the job site is assumed. In practice, the
differences in materials, substrates and actual site conditions are such that no warranty in respect of
merchantability of, or fitness for, particular purpose, nor any liability arising out of any legal relationship
whatsoever, can be inferred either from this information, or from any written and/or oral recommendations, or
from any other advice offered by the Company. The Company also has no express or implied knowledge of any
particular purpose for which the product is required and any such information given will not be taken into
account in the supply of this product. No responsibility or liability by the Company will be accepted for misuse,
misreading or derivation from recommended guidelines in respect of this product and the user shall
determine the suitability of the product for his intended use and assume all risks and liability in connection
therewith. The information contained in our brochure may change at any time without notice. Any use of this
product, Sure-Stop® PVC Waterstop, in any application should be approved as suitable for use/application by
the Design Engineer and Project Manager.
CORKJOINT (MALAYSIA) SDN BHD 383102-H CORKJOINT (SINGAPORE) PTE LTD 200716724-K
No. 51, Jalan BRP 8/2, Bukit Rahman Putra Industrial No. 10 Buroh Street #02-26 & 27, West Connect
Park, 47000 Sungai Buloh, Selangor, MALAYSIA Building, SINGAPORE 627564
Adopted from US Army Corps of Engineers "Waterstop and other joint materials "EM1110-2-2102
Profile Type H₂O Head Resistance Profile Type H₂O Head Resistance
CJ923 14 metres CJ951 22 metres
CJ924 22 metres CJ952 30 metres
CJ925 37 metres CJ953 40 metres
CJ926 48 metres CJ954 56 metres
CJ927 14 metres CJ955 22 metres
CJ928 22 metres CJ956 30 metres
CJ929 37 metres CJ957 40 metres
CJ930 48 metres CJ958 56 metres
Note: The above figures are estimates only. Please refer to our Sure-Stop PVC
Waterstop International Profiles product brochure for reference to profile type.
Note: The products design and performance, its intended use, installation and final
confirmation and approval for use, must be provided by the project’s Design
Engineer and Project Manager.
info@corkjoint.com
www.corkjoint.com © Corkjoint 2012. All Rights Reserved
SIRIM QAS International Sdn. Bhd.
SIRIM QASNo.:
(Company International Sdn.Bhd.
199601037981 (410334-X)
(410334-X))
No.1, Persiaran Dato’ Menteri, Section 2, P.O.BOX 7035,
40700Persiaran
No.1, Shah Alam, Selangor
Dato’ Darul
Menteri, Ehsan,
Section Malaysia.
2, P.O. Box 7035
Tel: 03-55446252
40700 Shah Alam, Selangor Darul Ehsan, Malaysia
Fax: 03-55446044/40
Tel: 03-55446272
www.sirim-qas.com.my
Fax: 03-55446039
www.sirim-qas.com.my
TEST REPORT
Description of Test : The test results of the submitted test sample are described in
Results Pages 4 and 5 of this test report.
Approved Signatories:
......................................... .....................................................
(Nomaizura Zakaria) (Rahmad Abd Shukor)
Testing Executive Head
Plastics and Composite Materials Section
Testing Services Department
SIRIM QAS International Sdn.Bhd. (410334-X)
No.1, Persiaran Dato’ Menteri, Section 2, P.O.BOX 7035,
REPORT NO.: 2020PC0768
40700 PAGE: 2 OF 5
Shah Alam, Selangor Darul Ehsan, Malaysia.
This Test Report Tel:
refers03-55446252
only to samples submitted by the applicant to SIRIM QAS International Sdn. Bhd. and tested by SIRIM QAS
International Sdn.Fax:
Bhd.03-55446272
This Test Report shall not be reproduced, except in full and shall not be used for any purpose by any means or
forms (including www.sirim-qas.com.my
but not limited to advertising purposes) without written approval from the Chief Executive Officer, SIRIM QAS
International Sdn. Bhd. Please refer the last page for Conditions Relating to the Use of Test Report.
Methods of Test:
1) ASTM D412: 2015a - Standard Test Methods for Vulcanized Rubber and Thermoplastic
Elastomers – Tension
4) BS 2782-6: Methods 620A to 620D: 1991 - Methods of Testing Plastics – Part 6: Dimensional
Properties – Methods 620A to 620D: Determination of Density and Relative Density of Non-
Cellular Plastics
5) BS EN 60811-3-2: 1995 IEC 811-3-2: 1985 - Insulating and Sheathing Materials of Electric
Cables – Common Test Methods – Part 3: Methods Specific to PVC Compounds – Section 2:
Loss of Mass Test – Thermal Stability Test
6) BS 2782: Part 1: Method 130A 1991 ISO 182-1: 1990 - Methods of Testing Plastics Part 1.
Thermal Properties Method 130A. Determination of the Thermal Stability of Polyvinyl Chloride
by the Congo Red Method
SIRIM QAS International Sdn.Bhd. (410334-X)
No.1, Persiaran Dato’ Menteri, Section 2, P.O.BOX 7035,
REPORT NO.: 2020PC0768
40700 PAGE: 3 OF 5
Shah Alam, Selangor Darul Ehsan, Malaysia.
This Test Report Tel:
refers03-55446252
only to samples submitted by the applicant to SIRIM QAS International Sdn. Bhd. and tested by SIRIM QAS
International Sdn.Fax:
Bhd.03-55446272
This Test Report shall not be reproduced, except in full and shall not be used for any purpose by any means or
forms (including www.sirim-qas.com.my
but not limited to advertising purposes) without written approval from the Chief Executive Officer, SIRIM QAS
International Sdn. Bhd. Please refer the last page for Conditions Relating to the Use of Test Report.
Description of Sample:
Four (4) cut pieces of test specimens shown in Figure 1 received on 10 September 2020.
Results:
Test parameters:
Specimen type: Dumbbell Die C
2 Elongation at Break 500 % Test speed: 500 mm/minute
Gauge length: 25 mm
Number of specimens tested: 5
Test parameters:
Time interval: 15 seconds
Specimen thickness: 6.0 mm
Number of layer: 1
Number of readings taken: 10
Test parameters:
Method 1
Temperature: 23°C
Duration: 24 hours
Number of specimens tested: 3
Results:
Test parameters:
Method 1
Immersion liquid: Water
Test temperature: 25°C
Number of specimens tested: 10
Test parameters:
Test Specimen: Dumb-bell shaped
test pieces
Temperature: 80°C
Duration: 7 days
1. A Test Report will be issued in respect of Testing Services conducted and shall relate only to the sample actually tested. SIRIM QAS
International makes no warranty whatsoever and the Applicant shall not represent in any manner that any duplication or mass production
of the Product is same as the sample actually tested or that SIRIM QAS International has tested any of the duplicated or mass-produced
Product. When a statement of conformity to a specification or standard is applied, the Measurement Uncertainty of test has been
considered.
2. The Test Report shall not be amended, changed, varied or modified in any manner whatsoever by the Applicant or otherwise.
3. If the Test Report is to be furnished to any third party or to the public, each such Test Report shall be furnished in full, legible and in its
entirety.
4. The Test Report shall not be reproduced and shall not in any event be used for any advertising purposes or whatsoever without written
approval from the Chief Executive Officer of SIRIM QAS International of No 1, Persiaran Dato’ Menteri, Building 8, Section 2, P.O. Box
7035, 40700 Shah Alam, Selangor Darul Ehsan.
5. Customer (Applicant/Manufacture/Factory, etc.) is not permitted to use any SIRIM QAS International, SIRIM or other SIRIM’s subsidiaries
logo or words on packaging, sample’s manual, technical specification, brochures/flyers or any other means without the prior written
approval from the Chief Executive Officer of SIRIM QAS International.
6. If such approval is obtained from the Chief Executive Officer of SIRIM QAS International, the Applicant may only include the phrase, “A
sample of this product has been tested by SIRIM QAS International (Test Report No) ... (dated) .… (for what test) … (to which standard)”
or such similar words which stress that only the Sample was actually tested. This phrase shall only be used for the purpose of product
advertisement or product promotion (eg; brochures). For avoidance of doubt, the statement shall not be used on the sample and
packaging of the sample.
7. In the event there is an investigation from a Government Regulatory Agency concerning the Applicant's Test Report, SIRIM QAS
International may disclose the information pertaining to the Test Report for purposes of such investigation.
8. Further or in the alternative, it is strictly forbidden unless with prior written approval from the Chief Executive Officer of SIRIM QAS
International, to represent in any manner whatsoever that SIRIM QAS International, SIRIM and/or other SIRIM’s subsidiaries has
endorsed, approved or validated the Product of the Applicant in any manner whatsoever.
9. In the event the Applicant is found in breach of this provision, SIRIM QAS International, SIRIM and/or other SIRIM’s subsidiaries without
prejudice to any other rights and remedies may take whatever action necessary including but not limited to:
a) Informing and placing a notice in the media;
b) Obtaining an injunction from Court (cost on a solicitor-client basis to be borne by the Applicant);
c) Refusing to accept any further Product for Testing Services from the Applicant or whosoever related to the Applicant, whether
subsidiary or otherwise;
d) Instructing the Applicant to withdraw and recall the advertisement, statement or document in question and advertise a clarification
and apology to SIRIM QAS International, SIRIM and/or other SIRIM’s subsidiaries twice in a national publication of SIRIM QAS
International’s choice at the Applicant's sole cost; and
e) Informing or lodging a report pertaining the Applicant's Test Report with the relevant authorities.
10. SIRIM QAS International is committed in supporting an environmentally-friendly business practices by reducing paper consumption,
therefore we do not issue any hard copy of Test Report to the Applicant. However, certified true copy(ies) of the Test Report may be
issued upon request by the Applicant upon payment of the relevant fee.
11. Issuance of Amendment Report due to the following reasons are chargeable to the Applicant :
a) Changes in details of the Applicant name and/or address;
b) Changes in details of the Manufacturer’s name and/or address;
c) Changes in details of the Factory location name and/or address;
d) Changes in details of the model and/or type designation
12. However, issuance of Supplementary Report due to the following reasons are FOC :
a) Misprints and typo errors;
b) Missing technical information as agreed in PP1 form;
c) Test data not reported;
d) Mistake in reporting of test data
13. Corrections to report shall only be allowed if the date of issuance of the original report has not exceeded 6 months and shall be limited to
maximum 3 times, after either case whichever occurs earlier, an Amendment or a Supplementary Report shall not be issued.