Professional Documents
Culture Documents
Cruise Control Switch Circuit
Cruise Control Switch Circuit
Print Exit
DESCRIPTION
The cruise control main switch is used to turn the cruise control system on and off, as well as operate 7 functions:
SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST)
functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise
control main switch is an automatic return type switch which turns on only while operating it in the direction of
each arrow and turns off after releasing it. The internal contact points of the cruise control main switch turn on
with switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to
control the SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL functions.
WIRING DIAGRAM
NOTICE:
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as
airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for
Supplemental Restraint System.
for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type
A)>PRECAUTION
for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type
https://toyotamanuals.com.au/docs/hilux-service-repair-manua…/RM100000000KZR9.html?PUB_TYPE=RM&MODE=3#RM100000000KZR9_06 Page 1 of 7
Inspection Procedure - Toyota Service Information 11/3/17, 6(59 pm
B)>PRECAUTION
PROCEDURE
Execute
OK:
When the cruise control main switch is operated, the display changes as shown above.
Result:
Proceed to
OK
NG
OK
https://toyotamanuals.com.au/docs/hilux-service-repair-manu…/RM100000000KZR9.html?PUB_TYPE=RM&MODE=3#RM100000000KZR9_06 Page 2 of 7
Inspection Procedure - Toyota Service Information 11/3/17, 6(59 pm
NG
Result:
Proceed to
OK
NG
OK
NG
a.
https://toyotamanuals.com.au/docs/hilux-service-repair-manu…/RM100000000KZR9.html?PUB_TYPE=RM&MODE=3#RM100000000KZR9_06 Page 3 of 7
Inspection Procedure - Toyota Service Information 11/3/17, 6(59 pm
Disconnect the spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2 connector.
*1: w/ Vehicle Stability Control System
*2: w/o Vehicle Stability Control System
Result:
Proceed to
OK
NG
OK
NG
a. Remove the spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2.
*1: w/ Vehicle Stability Control System
*2: w/o Vehicle Stability Control System
b. Inspect the spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2.
*1: w/ Vehicle Stability Control System
*2: w/o Vehicle Stability Control System
https://toyotamanuals.com.au/docs/hilux-service-repair-manu…/RM100000000KZR9.html?PUB_TYPE=RM&MODE=3#RM100000000KZR9_06 Page 4 of 7
Inspection Procedure - Toyota Service Information 11/3/17, 6(59 pm
Result:
Proceed to
OK
NG
OK
NG
5.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY OR SPIRAL
CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a. for 2TR-FE
i. Disconnect the G4 spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2 connector.
*1: w/ Vehicle Stability Control System
*2: w/o Vehicle Stability Control System
iii. Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Specified
Condition
Connection Condition
G4-1 (CCS) -
Always Below 1 Ω
G45-22 (CCS)
G4-2 (ECC) -
G45-21 Always Below 1 Ω
(ECCS)
G4-1 (CCS) or
10 kΩ or
G45-22 (CCS) Always
higher
- Body ground
b. for 1KD-FTV
i. Disconnect the G4 spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2 connector.
*1: w/ Vehicle Stability Control System
*2: w/o Vehicle Stability Control System
iii. Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Specified
Condition
Connection Condition
G4-1 (CCS) -
Always Below 1 Ω
G84-21 (CCS)
G4-2 (ECC) -
https://toyotamanuals.com.au/docs/hilux-service-repair-manu…/RM100000000KZR9.html?PUB_TYPE=RM&MODE=3#RM100000000KZR9_06 Page 5 of 7
Inspection Procedure - Toyota Service Information 11/3/17, 6(59 pm
G4-1 (CCS) or
10 kΩ or
G84-21 (CCS) Always
higher
- Body ground
iii. Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Specified
Condition
Connection Condition
G4-1 (CCS) -
Always Below 1 Ω
G86-26 (CCS)
G4-2 (ECC) -
Always Below 1 Ω
Body ground
G4-1 (CCS) or
10 kΩ or
G86-26 (CCS) Always
higher
- Body ground
d. for 1GR-FE
i. Disconnect the G4 spiral with sensor cable sub-assembly connector.
iii. Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Specified
Condition
Connection Condition
G4-1 (CCS) -
Always Below 1 Ω
G88-1 (CCS)
G4-2 (ECC) -
Always Below 1 Ω
Body ground
G4-1 (CCS) or
10 kΩ or
G88-1 (CCS) - Always
higher
Body ground
Result:
Proceed to
OK
NG
OK
REPLACE ECM
https://toyotamanuals.com.au/docs/hilux-service-repair-manu…/RM100000000KZR9.html?PUB_TYPE=RM&MODE=3#RM100000000KZR9_06 Page 6 of 7
Inspection Procedure - Toyota Service Information 11/3/17, 6(59 pm
NG
https://toyotamanuals.com.au/docs/hilux-service-repair-manu…/RM100000000KZR9.html?PUB_TYPE=RM&MODE=3#RM100000000KZR9_06 Page 7 of 7