Se€cos
Elektronische Banelemente
STP1117Sxx Series
1.0 Low Dropout Positive
Adjustable or Fixed-Mode Regulator
TRanis Compleat Proauct
‘Asulix fC" speotiesnaloaen
DESCRIPTION
The STP1117Sxx series of positive adjustable and
fixed regulators are designed to provide 1A with high |
efficiency. All internal circuitry is designed to operate
down to 1.4V input to output differential
(On-chip trimming adjusts the reference voltage to
1%, Current mit the typical value of 1.5A allows to
‘minimizing the stress on both the regulator and the
ower source circuitry under overload congitions.
FEATURES
‘Adjustable or Fixed Output 1.2V,1.8V,25V.3.3V
Output Current of 14
Low Dropout, 1.2 V typ. at 1A Output Current
0.04% Line Regulation
0.2% Load Regulation
400% Thermal Limit Burn-in
Fast Transient Response
APPLICATIONS
High Efficiency Linear Regulators
+ Post Ragulators for Switching Supplies
+ Adjustable Power Supply
ADJ (Gnd) Vout Vin
> o
MARKING
Part Number | Marking out
a AAG [ 575.
STPI7SA THIT7SA pr | Bee
STPINITS2 aH17512, 11a
seusi ase The las lotter(s) of PartNo.
STPMITS25 1117825) denote the Output Voltage
STPINTS33 7117533,
PACKAGE INFORMATION
Package MPQ Leader Size
‘SOT-223 3K 43 inch
TYPICAL APPLICATION CIRCUIT
Fixed Voltage Regulator Adjustable Voltage Regulator
Vn fBh Sy stpati7s our] ae
ms ee ¢
a Ove Fant. Min a T F104 tant, min
‘our tant Tour Tant ni
= = = 1330, 196
Notes: Ro.
1) CL needed if device is far from filter capacitors. 2320, 196
2) C2 minimum value required for sta
Vour = Veer * (1+ R2/RL) + laps RZ
2r-dun-2017 Rev B
Page 1 of 6Se€cos
Elektronische Banelemente
STP1117Sxx Series
1.0 Low Dropout Positive
Adjustable or Fixed-Mode Regulator
ABOSLUTE MAXIMUM RATINGS
Parameter ‘symbol Value Unit
input Voltage w 2 v
IMinimum ESD Rating (HEM) Veso 3 Kv
Lead Temperature (Soldering, 10sec.) T 300 c
[Thermal Resistance Ambiont Ambient Rac 18 ow
[Operating Junction Temperature Range ws 40-1125 c
[stocage Temperature Range Tag 65-4180 c
Tee
‘Stresses above thse lista in“Absclule Maximum Ratings’ may cause permanant damage tothe device. This is astross only rating and
‘operation ef the devco al hese or anyother conditions above those indicated i th
FUNCTIONAL BLOCK DIAGRAM
vin
pataionl sectons ofthis specticabon is nt pled
Vout
For adjustable
voltage device]
For aed
voltage
device
2r-dun-2017 Rev B
Page 2 of 6Se€cos
Elektronische Banelemente
STP1117Sxx Series
1.0 Low Dropout Positive
Adjustable or Fixed-Mode Regulator
ELECTRICAL CHARACTERISTICS(.«
omf, 125%: unless alhorvise spoctiad)
Parameter Symbol | Device Typ. | Max | Unit Test conditions
[Operating Voltage * Vw - - 16 v
Taa2 | 2250 [1208 | roartowa vars
Reference Voltage * Voc Adj . V |hqo=10ma 1A,
1.225 | 1.250 | 1.275 }1.5V s VieVour $ 10V
Nisvor= 150,
All fixed as = hte |Variator from nominal Vout
i so
output votage Vo 2 2 | % fisvsvicvans to,
[oomomate
Vor=12v] 3 2 |Variator from nominal Vour*
xp vatage ecuracy wy hneuapr ev uae
ues Yt vo | oa fae | 0 | 06 | % finever15\, tow=t0mA
[Line Regulation LNR- All - 0.04 | 0.238 | % [lom=10mA, 1.5V 5 Vin-Vours 10V*
|Load Regulation ' LOR Al - 0.2 | 0.25 | % [Vw=Vour=1.5V, lLoan=10mA to1A*
[Minimum Load Current h agj : 2 7 mA [Vn=5¥, Vao0V*
[ecuna Pin Curent Aine | [a5 | 10 | ma We-Vor=16V Laur TOmA WIA
[Adjust Pin Current Adj - 38 60 | UA [hos 10mA, 1.5V 3 Vin-Vour s 10V *
[Caren init ao pts 2 DA fenouet"
[Ripple Rejection ? RR All 60. = - dB [Vix-Vour=2.5V, lho
[Dropout Voltage ‘> Vo All - 12 14 Vv |how=1A*
Heperture Gosficen ALL [oot [pve fanveurt t
Nes
“ Lowduty ue testing wth Kevin connections required,
12042 input pple (Casfor ADJ = 25,F)
2
3 Nour, AVoee"186
4
“Tho speeiteatins wevon apply over the ful temperature range: AO $ TNS 1266.
2r-dun-2017 Rev B
Pape 3 of 6S€COSs
EleKtronisehe Bauelemente
STP1117Sxx Series
1.0 Low Dropout Positive
Adjustable or Fixed-Mode Regulator
TYPICAL CHARACTERISTICS
Load Transient Response
batts
ee
[Ot nee coos Vin
eran eae | co epee eee ee Pee Dee | Po |e
Line Transient Response
Aa ee ga ee
a)
Load Regulation (Input Voltage = 5V)
ans
ane
3323
aaa
Line Regulation (Output Current = 100mA)
| an i
any
ane
ais
Output voltage (v)
STPINI7S33
Output Current (A)
Output Voltage vs. Input Voltage
B 1s
9 a
Input Vokage (V)
Input Current vs. Input Voltage
ouput votage(¥)
Input Voltage (V)
stP1117833
Input current (ma)
Inpurvotage(V)
Anyhoo eaten nite eres sy
2r-dun-2017 Rev B
Page 4 of 6S€COSs
Elektronische Banelemente
STP1117Sxx Series
1.0 Low Dropout Positive
Adjustable or Fixed-Mode Regulator
TYPICAL CHARACTERISTICS
Current Limit vs. Input Voltage
STP1N17833
Currenim (8)
Inpurvoragev)
Output Voltage vs. Temperature (2.5V)
Output Voltage vs. Temperature (3.3V)
235
a2
utputVortage(
aa
Temnperature( C)
Output Voltage vs. Temperature (1.8V)
26 19
= 3s =
3 S18
gs 3
3 3
3 us $ us
3 i
a” 3
as 165,
so 0 5075 1m a a
Temperature( C) “emperature(C)
PSRR vs. Frequency
0 | 1
nf 1 |
ttt |
3 so | AH
wo |
2»
oor on 1 0 10
Frequency (KH)
2I-Jun 2017 Rew
Pape 6 of 6Se€cos Lika epee
Elektronische Bauelemente Adjustable or Fixed-Mode Regulator
APPLICATION INFORMATION
Output Voltage STPINTS
The STP1117S develops a 1.25V reference Voltage
Between the output and the adjust terminal. By placing
‘resistor between these two terminals, a constant current
Is cause to flow through R1 and down through R2 to set the
(Overall output voltage. Normally, this current is chosen to be
the specified minimum load current of 10mA. For fixed voltage
devices R1 and R2 are included in the device.
Figure 1: Basic adjustable regulator.
Load Regulation
When the adjustable regulator is used, load regulation
will be limited by the resistance of the wire connecting the
regulator to the load. The data sheet specification foe load yo
regulation is measured at the output pin of the device
Best load regulation is obtained when the top of the
resistor divider (R1) is ted directly to the output pin of the
device not to the load. For fixed voltage, devices the top
of Ris internally connected to the output, and the ground
pin can be connected to low side of the load. If R1 is
Connected to the load, Ris multipiod by the divider ratio,
the effective resistance between the regulator and the load
would be: Ratotoos
Figure 2: Connections for best load regulation.
sTPttt75 Your
‘bur °
i
Connect
Re (1 + R2IR1), Re = Parasitic Line Resistance
Input Capacitor
{An input capacitor of {OF or greater is recommended,
Tantalum or alurninum electrolytic capacitors can be used for
bypassing. Largor Values will improve ripple rejection by
bypassing the input to the regulator.
‘Output Capacitor
The STP1117S requires an output capacitor to maintain stability and improve transient response. Proper
capacitor selection is important o ensure proper operation. The STP1117S output capacitor selection is dependent
upon the ESR (equivalent series resistance) of the output capacitor to maintain stability. When the output
capacitor is 10pF or greater, the output capacitor should have an ESR less than 10. This will improve transient
response as well as promote stability. A low-ESR solid tantalum capacitor works extremely well and provides
‘good transient response and stability over temperature
Aluminum electrolytic can also be used, as long as the ESR of the capacitor is <10. The value ofthe output
Capacitor can be increased without limit. Higher capacitance values help to improve transient response and ripple
rejection and reduce output noise.
ple Rejection
The curves for Ripple Rejection were generated using an adjustable device withthe adjust pin bypassed.
With a 25uF bypassing capacitor, 7SdB ripple rejection is obtainable at any output level. The impedance of
the adjust pin capacitor, atthe rippie frequency, should be