Professional Documents
Culture Documents
Ltn140at20 D01
Ltn140at20 D01
TO : Dell / Quanta
DATE : June. 20, 2011
SAMSUNG TFT-LCD
N
NOTE : Extension code [ -D ]
→ LTN140AT20-D
- Surface type [ Glare ]
The information described in this SPEC is preliminary and can be changed without prior notice.
APPROVED BY :
Samsung Secret
3. Electrical Characteristics - - - - - - - - - - - - - - - - - - - ( 10 )
3.1 TFT LCD Module
3.2 LED Driver
4. Block Diagram - - - - - - - - - - - - - - - - - - - ( 13 )
4.1 TFT LCD Module
4.2 LED connection and placement
6. Interface Timing - - - - - - - - - - - - - - - - - - - ( 19 )
6.1 Timing Parameters
6.2 Timing Diagrams of interface Signal
6.3 Power ON/OFF Sequence
7. Outline Dimension - - - - - - - - - - - - - - - - - - - ( 22 )
8. Packing - - - - - - - - - - - - - - - - - - - ( 23 )
11. EDID - - - - - - - - - - - - - - - - - - - ( 28 )
Samsung Secret
Feb. 21, 2011 P00 All The preliminary specification was issued first.
Jun. 4, 2011 A00 - The approval specification of LTN140AT20-D model was issued first.
Samsung Secret
FEATURES
• High contrast ratio, high aperture structure
• 1366 x 768 pixels resolution
• Low power consumption
• Fast response time
• LED BLU structure
• DE (Data enable) only mode.
• 3.3V LVDS Interface
• On board EEDID chip
• RoHS compliance
• Halogen free product
• As free compliance
• APS function
APPLICATIONS
• Notebook PC
• If the usage of this product is not for PC application, but for others, please contact SEC.
GENERAL INFORMATION
Samsung Secret
Note (1) Temperature and relative humidity range are shown in the figure below.
95 % RH Max. (40 °C ≥ Ta)
Maximum wet - bulb temperature at 39 OC or less. (Ta > 40 °C ) No condensation
60
Operating Range
( 50,50.4 )
40
( 60,27.7 )
20
5
Storage Range
0
-40 -20 0 20 40 60 80
Temperature (OC)
(2) 2ms, half sine wave, one time for ±X, ±Y, ± Z.
(3) 5 - 500 Hz, random vibration, 30min for X, Y, Z.
(4) At testing Vibration and Shock, the fixture in holding the Module to be tested have to be
hard and rigid enough so that the Module would not be twisted or bent by the fixture.
Samsung Secret
Samsung Secret
The following items are measured under stable conditions. The optical characteristics
should be measured in a dark room or equivalent state with the methods shown in Note (5).
Measuring equipment : TOPCON SR-3
Contrast Ratio
CR 500 600 - - (1), (2), (5)
(5 Points)
Response Time at Ta
TRT - 16 25 msec (1), (3)
( Rising + Falling )
Average Luminance
YL,AVE 170 200 - cd/m2 (1), (4)
of White (5 Points)
Normal
RX 0.577
Red Viewing
RY Angle 0.352
φ=0
GX 0.345
Green θ=0
Color GY 0.565
Typ Typ (1), (5)
Chromaticity -
BX -0.03 0.165 +0.03 PR-650
( CIE )
Blue
BY 0.118
WX 0.313
White
WY 0.329
θL 40 - -
Hor.
θR 40 - - (1), (5)
Viewing Angle CR ≥ 10 Degrees
φH 15 - - SR-3
Ver.
φL 30 - -
Color Gamut CG - 45 - %
13 Points
δL - - 1.6 - (6)
White Variation
Samsung Secret
θL
θR
φH 12 O’clock
φL
θ L =90o x y direction
φ H = 90o
Note 2) Definition of Contrast Ratio (CR) : Ratio of gray max (Gmax) ,gray min (Gmin)
at 5 points(4, 5, 7, 9, 10)
TR TF
100%
90%
Optical
Response
10%
0%
Time
Note 4) Definition of Average Luminance of White : measure the luminance of white at 5 points.
(30%) (50%) (70%)
VIEW AREA
: test point
Samsung Secret
Photo-detector
( TOPCON BM-5A
PR-650 )
Field = 2°
50 cm
: test point
Samsung Secret
Vsync Frequency fv - 60 - Hz
Note (1) Display data pins and timing signal pins should be connected.( GND = 0V )
(2) f = 60Hz, f = 69.3MHZ, V = 3.3V , DC Current.
(3) P
Power
V
owerdissipation
dissip a t ipattern
D C LK
on pattern D
VIEW AREA
Samsung Secret
3.3V M1
2SK1059
VDD ( LCD INPUT)
FUSE
R1 C1
47K 1uF
R2
CONTROL SIGNAL M2
(HIGH to LOW) 2SK1399
1K
12V
R3 C2
C3 47K
10000pF
1uF
0.1V
GND
470us
Samsung Secret
Note (1) Life time (Hr) of LEDs can be defined as the time in which it continues to operate under the
condition Ta= 25 ± 2 °C and IF = 23mA until one of the following event occurs.
When the brightness becomes 50% or lower than the original.
External PWM
Dimming Control FBLIM 0.2 - 1 kHz
Frequency (BLIM)
Samsung Secret
Source
14.0” HD
Driver
Gamma IC TFT-LCD Panel
DC-DC
Converter Generator
VCOM
Generator
Gate Pulse
Generator
SOURCE PCB
Video Signal
Control Signal
V
VCOM
Gamma
DVDD
AVDD
Von/Voff
Samsung Secret
1 NC No connection
10 GND Ground
13 GND Ground
16 (/% (SPVOE
17 CLK- - LVDS differential clock input
19 GND Ground
20 ~ 21 NC No connection
22 GND Ground
23 ~ 24 NC No connection
25 GND Ground
26 ~ 27 NC No connection
28 GND Ground
29 ~ 30 NC No connection
34 NC No connection
Samsung Secret
Pin No. Name RGB Signal Pin No. Name RGB Signal
51 TxIN0 R0 14 TxIN14 G5
52 TxIN1 R1 15 TxIN15 B0
54 TxIN2 R2 19 TxIN18 B1
55 TxIN3 R3 20 TxIN19 B2
56 TxIN4 R4 22 TxIN20 B3
3 TxIN6 R5 23 TxIN21 B4
4 TxIN7 G0 24 TxIN22 B5
11 TxIN12 G3 30 TxIN26 DE
LVDS INTERFACE
Note : The LCD Module uses a 100ohm resistor between positive and negative lines of each
receiver input.
Samsung Secret
T
TxCLK OUT
RxCLK IN
T/7
DE Vsync Hsync B5 B4 B3 B2
B1 B0 G5 G4 G3 G2 G1
Samsung Secret
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -
Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 -
Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 -
Basic Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 -
Colors Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 -
Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 -
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 -
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R0
Dark 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R1
Gray ↑ 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R2
Scale : : : : : : : : : : : : : : : : : : :
R3∼R60
Of : : : : : : : : : : : : : : : : : : :
Red ↓ 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 R61
Light 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 R62
Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 R63
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G0
Dark 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 G1
Gray ↑ 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 G2
Scale : : : : : : : : : : : : : : : : : : :
G3∼G60
Of : : : : : : : : : : : : : : : : : : :
Green ↓ 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0 G61
Light 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 G62
Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 G63
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B0
Dark 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 B1
Gray ↑ 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 B2
Scale : : : : : : : : : : : : : : : : : : :
B3∼B60
Of : : : : : : : : : : : : : : : : : : :
Blue ↓ 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 B61
Light 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 B62
Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 B63
Note 1) Definition of gray :
Rn: Red gray, Gn: Green gray, Bn: Blue gray (n=gray level)
Note 2)Input signal: 0 =Low level voltage, 1=High level voltage
Samsung Secret
1 1366
Line 1 R G B R G B R G B R G B
LTN140AT20-D Panel
Line 768 R G B R G B R G B R G B
Samsung Secret
One Line
Cycle TH 1440 1462 1620 Clocks -
Scanning Time
TV
DE
TH
DCLK
TC
THD
DE
Samsung Secret
T2 T3
VALID
Signals
0V
T8 T9
T10 T11
0V T12 T13
PWM
0V T14 T15
B/L Enable
0V T5 T6
0 T3 ≤50 Delay from valid data OFF to VDD OFF at power Off
200 ≤T6 Delay from valid data off to B/L disable at power Off
10 T8 Delay from valid data on to LED driver Vin rising time 10%
10 T9 Delay from LED driver Vin falling time 10% to valid data Off
10 T12 Delay from LED driver Vin rising time 90% to PWM ON
10 T13 Delay from PWM Off to LED driver Vin falling time 10%
Note : Backlight may flash if interface signal remains floating state at invalid period.
Samsung Secret
NOTE.
(1) The supply voltage of the external system for the module input should be the same
as the definition of VDD.
(2) Apply the lamp voltage within the LCD operation range. When the back-light turns on
before the LCD operation or the LCD turns off before the back-light turns off, the
display may momentarily become white.
(3) In case of VDD = off level, please keep the level of input signals on the low or keep
a high impedance.
(4) T4 should be measured after the module has been fully discharged between power
off and on period.
(5) Interface signal shall not be kept at high impedance when the power is on.
Samsung Secret
Samsung Secret
ʹ Ά΄
ͽ΅Ϳͥ͢͡Ͳ΅ͣ͡
;Ͳ͵Ͷ͑ͺͿ͑ʹͺͿͲ
΄ΒΞΤΦΟΘ͑ΔΠΟΗΚΕΖΟΥΚΒΝ
Ͷ
·
͠
ͺ
΄
ͺ
Ϳ
8. PACKING Approval
1. CARTON(Internal Package)
STEP 1. Putting into the Zipper Bag STEP 2. Putting on the paper tray
STEP 5. Inserting the Box STEP 4. Folding the Paper Tray STEP 3. 2 Module / 1 Paper Tray
Samsung Secret
Product Code
Y Line
LTN140AT20
1125
14.0”HD 6MBFxxxxxx D01 40 mm
0GN264
04DKPR
CN- 04DKPR A00
A00
MADE IN China
80 mm
Parts name : LTN140AT20-D
Lot number : 6MBFxxxxxx
Inspected work week : 1125
DP/N : Dell Part Number (“04DKPR” is for LTN140AT20-D)
Samsung Secret
LTN140AT20-D
REV.A00
Vendor ID/Loc :
04DKPR 21320/39792
30
Samsung Secret
(a) When the module is assembled, It should be attached to the system firmly
using every mounting holes. Be careful not to twist and bend the modules.
(b) Refrain from strong mechanical shock and / or any force to the module. In addition to
damage, this may cause improper operation or damage to the module and LED back-light.
(c) Note that polarizers are very fragile and could be easily damaged. Do not press or scratch
the surface harder than a HB pencil lead.
(d) Wipe off water droplets or oil immediately. If you leave the droplets for a long time,
Staining and discoloration may occur.
(e) If the surface of the polarizer is dirty, clean it using some absorbent cotton or soft cloth.
(f) The desirable cleaners are water, IPA (Isoprophyl Alcohol) or Hexane.
Do not use Ketone type materials(ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl
chloride. It might permanent damage to the polarizer due to chemical reaction.
(g) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or
mouth . In case of contact with hands, legs or clothes, it must be washed away thoroughly
with soap.
(h) Protect the module from static , it may cause damage to the C-MOS Gate Array IC.
(i) Use fingerstalls with soft gloves in order to keep display clean during the incoming
inspection and assembly process.
(l) Do not adjust the variable resistor which is located on the back side.
(m) Protection film for polarizer on the module shall be slowly peeled off just before use so
that the electrostatic charge can be minimized.
(n) Pins of I/F connector shall not be touched directly with bare hands.
Samsung Secret
(c) The module shall be stored in a dark place. It is prohibited to apply sunlight or fluorescent
light during the store.
3. OPERATION
(a) Do not connect, disconnect the module in the “ Power On” condition.
(b) Power supply should always be turned on/off by following item 6.3
“ Power on/off sequence “.
(c) Module has high frequency circuits. Sufficient suppression to the electromagnetic
interference shall be done by system manufacturers. Grounding and shielding methods
may be important to minimize the interference.
(d) The FPC cable between the LED chips and its converter power supply shall be a
minim
minimized ack-light
length and be connected directly . The longer cable between the back-light
and the converter
ized length may cause lower luminance of light source (LED).
and be
(e) The standard
connectedlimited warranty is only applicable when the module is used for general
notebook applications. If used for purposes other than as specified, SEC is not to be
longer
held reliable
cable for the defective operations. It is strongly recommended to contact SEC
to findbetween
out fitness for a particular purpose.
the b
4. OTHERS
(c) Do not exceed the absolute maximum rating value. ( the supply voltage variation, input
voltage variation, variation in part contents and environmental temperature, so on)
Otherwise the module may be damaged.
(d) If the module displays the same pattern continuously for a long period of time,it can be
the situation when the image “sticks” to the screen.
(e) This module has its circuitry PCB’s on the rear side and should be handled carefully in
order not to be stressed.
Samsung Secret
3 Header FF 11111111
4 Header FF 11111111
5 Header FF 11111111
6 Header FF 11111111
7 Header 00 00000000
8 EISA manufacture code = 3 Character ID 4C 01001100
9 EISA manufacture code (Compressed ASCII) A3 10100011
0A Panel Supplier Reserved – Product Code 41 01000001
0B Panel Supplier Reserved – Product Code 54 01010100
0C LCD module Serial No - Preferred but Optional (“0” if not used) 00 00000000
Vendor / Product
EDID Version
0D LCD module Serial No - Preferred but Optional (“0” if not used) 00 00000000
0E LCD module Serial No - Preferred but Optional (“0” if not used) 00 00000000
0F LCD module Serial No - Preferred but Optional (“0” if not used) 00 00000000
10 Week of manufacture 00 00000000
11 Year of manufacture 15 00010101
12 EDID structure version # = 1 01 00000001
13 EDID revision # = 4 04 00000100
14 Video I/P definition = Digital I/P 90 10010000
15 Max H image size = (Rounded to cm) 1F 00011111
Parameters
Display
18 Feature support ( DPM (Standby, Suspend, Active), Color Type, Other Feature) 0A 00001010
19 Red/Green Low bit (RxRy/Gx G 01001011
1A Blue/White Low bit (BxBy/WxWy) C5 11000101
1B Red X Rx = 0.xxx 9C 10011100
Coordinates
Panel Color
Samsung Secret
Samsung Secret
5A Flag 00 00000000
5B Flag 00 00000000
5C Flag 00 00000000
5D Data Type Tag: Alphanumeric Data String (ASCII) FE 11111110
5E Flag 00 00000000
5F Dell P/N 1st Character 34 00110100
60 Dell P/N 2nd Character 44 01000100
rd
61 Dell P/N 3 Character 4B 01001011
62 Dell P/N 4th Character 50 01010000
Dell specific information
Timing Descripter #3
72 Panel Type & Configurations (Bulb/LED string #, Structure Revision, Panel Structure) 41 01000001
73 Frame Rate Details (SDRRS, DRRS, Max Frame Rate, Min Frame Rate) 21 00100001
Timing Descripter #4
79 Special Features #2 (In-Cell Touch, Interface, Over Drive, LVDS Channel or eDP Lane) 01 00000001
7B (If <13 char, then terminate with ASCII code 0Ah, set remaining char = 20h) 0A 00001010
7C (If <13 char, then terminate with ASCII code 0Ah, set remaining char = 20h) 20 00100000
7D (If <13 char, then terminate with ASCII code 0Ah, set remaining char = 20h) 20 00100000
Checksum
7E Extension flag (# of optional 128 EDID extension blocks to follow, Typ = 0) 00 00000000
7F Checksum (The 1-byte sum of all 128 bytes in this EDID block shall = 0) 77 01110111
Samsung Secret