Professional Documents
Culture Documents
Ss Gadkar
Ss Gadkar
Ss Gadkar
06 May 2021
Safety-
Fire control plan and location. Why is it kept in that location
Collision bulkhead and regulations
Length between perpendiculars
Duct keel
Motor/Mep-
Hunting gear
Pumps used in steering gear system and working
Effect of catfish
Electrical-
Earth neutral and insulated neutral..which is used on board
Earth fault indication? How to find earth fault
Motors onboard?
(Everything was asked in complete details, till you stop answering futher)
Safety -
Types of chemical tankers ( I got confused and didn't answer, later came to know he mean
ship types according to IBC code just used different words to confuse )
Category of Noxious Liquid substances.
Purifier room fire actions (what all safties present)
Hypermist system working
Electrical -
Electricity produced onboard
Alternator working
AVR function
How magnetism occurs in Alternator
What is trickle charging? how is it done? How is the circuit?
Motor / Mep -
Bottom end bearing clearance in 4 stroke (starting with piston position)
Thin shell bearing
Air compressor safties
SAFETY
Difference between hypermist and sprinkler
Spurling pipe
Annex 1 whole
Ums regulations
Welding safeties
Internal:subbarao sir
External:gadkar sir
Safety: 1) what procedure u will follow before entering fuel tank (proper procedure)
2) difference between hyper mist and sprinkler
3) How to extinguish fire in paint locker.
Type of engine?
Explain your engine.
Which fuel injection system?
Which Fuel Pump? (Cam operated)
Date - 1/12/2021
Surveyor- Sudhir Kumar Shrivastava
Ext: SS Gadakar
Function- Safety and Electrical
1) Type of ship
2) Garboard strake
3) Types of keel
4) Duct keel benefits
5) Types of floor
6) Collision bulkhead rules and regulations
Gadkar sir
Function 4b
Coc attempt
What type of ship
Scavenge fire
Steering gear everything and xx
Fuel injector testing
Interlocks in me
Turndown ratio and it’s significance
Piston measurement
T/C of AE vibrating actions
BDN contents
Air compressor valve checks
Motor
Engine specifications
Interlockks in me
Type of turbocharger on ae and me and why so
Decider
Fatigue failure
Failed
Mumbai
Internal meena
External ssgadkar
Function - 3
Camber
Rest forgot
Electrical
Steering gear safety
Power factor
Electrical
Power factor and significance
Cca w.r.t batteries
Induction motor principle
03.01.2022
Meena
ss gadkar
Electrical
.
Msb safeties
msb maintenance
Zener diode
Somemore
06 jan
Meena sir
ss gadkar sir
6 steam trap.
Mep
1 cylinder head over hauling.
2 steam trap.
Safety
Type of Ship
Cargo Hold Smoke detection System
How Alarm raised
Collision Bulkhead Regulations
Hyper mist Working
Marpol Annex Names
Int- meena
Safety
1.type of ship
2.statuatory certificate in SOLAS
3.Req of Collision Bulkhead
1.if in Star Delta star doesn't change to Delta? Reason and what will you check?
2.MCB and MCCB? Rating?
3.Alternator not sharing load equally. What checks?
4.Open circuit in motor and how to check? ( I forgot)
5.Motor sent ashore. It comes back. No time to test because pilot on board. What all
checks you make?
6.Classes of insulation details.
7.IP rating detail.
Result- Pass
6 Jan 2022
Noida
Safety
Meena Sir
Gadkar Sir
Type of ship
Freeboard Deck
Collision Bulkhead
Types of Floor
Continuous Synopsis Record
Fire fighting system in Paint Locker
How sprinkler system operates
Discharge Criteria as per Annex 1
Container Ship
Admit Card, CDC
Type of Ship
Shear Strake
《Internet disconnected 》
《Took me in meeting at last》
Only External-
Type of ship
Torsion Box
Type of Fire divisions A&B
Purpose of ISM8
All elements of ISM
Purpose of PSC
If ship registered in India and Inspection in India what it is called?
Purpose of GM
What is static stability
Thanks to all group members for answering queries and *specially Saheem bhai*
Bhai tumne itni madad kari..Tumko kabhi kuch zaroorat ho toh zaroor yaad karna
Ss gadkar sir
Safety and electrical
Safety
Collision bulkhead
Static and dynamic stability
How to find them
Dpa
Isolation valve func and location
What area isolation valve isiolate ,what will happen when we isloate from machinary
space how will water supply.
Electical
Clamp meter
How to use it
Single phasing
24-jan-2021
Internal: Sudhir Kumar
External: SS Gadkar
Time: 25 mins
Gadkar sir is very professional and listens calmly to everything. Expects more and more
4b and 6
Compressor valves why so many plates????
Told him that better surface area and better vibration dampening, didn’t look satisfied
Check if alarm true from ECR there will be an OMD alarm which will indicate that it wasn’t
a sensor failure, if not this then check locally the temperature of that unit and adjacent
unit crankcase, if confirmed yes then inform CE, inform bridge and ask to stop the engine
asap, then in mean time keep a fire hose and extinguisher standby, don’t stop any lube oil
pump and leave the ER for 45-60 mins and come back, check the temperature of the
crankcase and confirm all units okay, engage turning gear, open crankcase doors and
inspect what caused the omd alarm to trigger…
Sparks in funnel actions???Why cannot do soot blow???
I told him that I’ll check the EGE outlet temperature and compare with previous ones, If
temperature increasing rapidly it means that it’s an indication pf fire, then I told I’ll inform
CE, Tell bridge to stop the engine, will monitor the temperature of EGe locally also by
temperature gun, fire hose and extinguisher all rigged up, once engine stop not to stop
circulating pump, also 1 person to check the cascade tank level , if dropping it means then
tubes are leaking and then only we will stop circulating pump to avoid hydrogen fire and
further metal fire, also we’ll start boundary cooling in mean time and corresponding
temperature to check, once all okay open up EGE and inspection to be done check for any
damage or deformation of tubes caused because of fire.
Then he asked me that only fire can be reason for sparks nothing else? I told him if we had
done EGE washing in previous ports then sparks can come as the soot would be wet, also
about soot blow must not be done as in case of fire it can escalate the chances of fire as
we’re giving air, he then asked me do we do soot blow by air? I told in my ship we’d
sootblow donw by compressed air only unlike in other ships where steam is used, he said
ok good
Fuel pump lead and significance???
Fuel pump lead is the distance by which the fuel pump’s plunger is above the top surface
of spill port for that particular unit when at TDC, Lead tells us about the BOI, More lead
means Early BOI and vice versa…
VIT and significance???
I told abbreviated as Variable Injection Timing, and It’s the advance in the timing of fuel to
achieve the Pmax of 100% at 85% itsef, about Significance I told him that we’ll achieve
better power output with comparatively less fuel consumption and it’ll also reduce SFOC
Boiler burner routines???
If after overhauling pilot burner not firing reasons???
Stuffing box
AE bottom end bearing clearance??
Stop lube oil pump, engage turning gear, wait for temperature to come to normal,
isolation related and safety aspects I told him, then turn the engine to BDC of that unit
and insert feeler gauge between bottom half of shell and crank pin, also Taken at fwd and
aft of bearing and at sides also. Not taken at top half as it’s loaded
Where you’ll take clearance? At what point and how? Why not at top half????
Heat treatment done for gudgeon pin??
Nitriding
Types of heat treatment??
Difference between ME and AE lube oil?? Why TBN?? Why we use AE oil with that
particular TBN?? Why not for ME?? Etc etc
Told him about values, also told him that in AE same oil is used for liner lubrication but in
ME we have cylinder oil , so no need of high TBN of in crankcase and if we use then it
might cause calcium carbonate film between bearing and journal and also it’d be costly
affair to have such high volume of oil
Purpose of stuffing box?? Why?? What it selas?? What if it wasn’t there???
Cylinder oil getting scrapped off will enter crankcase there by contamining the crankcase
oil.
Also scavenge air will leak into crankcase causing crankcase to pressurize and we’ll also
loose air so it’ll affect the combustion and power output of the engine
Your 2/E told you to that tomorrow we’ll do unit decarb, what all preparation you’ll do in
your night watch???
I told him everything in detail like we’ll keep the spare piston ready, checks made on spare
piston like crown burnaway measurement, grooves width, presure testing to be done etc,
I told him that I’ll keep all spanners, hammer, buffing machine, buffing wheel, pneumatic
hoses, hydraulic jacks for cylinder head and their lifting tool, piston lifting tool, liner
ovality check template this all I’ll get on cylinder head platform and keep standby, also I
told him that I’ll check that the hydraulic pump has oil in it or not, also I’ll get some oil
standby and keep, then cylinder head studs have cap over them, I told I’ll open those caps
clean all the threads with wire brush and diesel and spray some WD 40 and leave so that
the threads don’t jamm up the next day while opening the hydraulic nuts, then I told I’ll
also keep the palm bolt jacks and distance piece standby at bottom platform, I’ll keep the
support stanchion or plates standby at the unit to do decarb, most importantly I told him
I’ll also inspect the shackle, slings if used any and belts it must be in good condition and as
per the SWL, at last I said also I’ll cross check with my seniors regarding the Immobilzation
and time period for the same!!!!
Manjhi sir.
ss gadkar sir
01/02/2022
Diaphragm in 2 stroke engine
Firing order
Backlash and how to measure
Reefer charging
Short cycling reason
Electrical
ICCP
What to check in overhauled motor
IR Test where to connect
Noida
Mep:
What all overhauls you have done - mainly question from AE
1) piston calibration of AE
2) how to measure bottom end bearing clearance
Check youtube channel MARINE HELP BOT you will get almost.. or telegram
Internal:- subharao
External:- ssgadkar
Function 3 safety
Type of ship
Collision bulkhead and regulations
Spurling pipe and use
Fighting system on board
And more
Clear
Internal:- subharao
External:- ssgadkar (good ,he is give time for thinking)
Function 3 safety
Type of ship
What is GT, NT, gross weight ,lightweight.
What is sheer streke
Garbord streke
Purifier room Fighting system on board
Hypermist system working
Sopep loker
what is ISM ,All about ISM
Clear
Ext: ss gadkar
Int: Subbarao
Fun. 3
What is Deep tank
Fwd and aft perpendicular
Subbarao
Ss gadkar
Function 4b (motor)
Type of engine
Firing order of engine i said 142653 he said why not 123456? What is the reason?
Thrust bearing
Intercooler location and purpose
Boiler blowdown
Difference between ME and AE lube oil
How soot is blown in boiler
Internal subarao
External Ss gadkar
Motor pass mep repeat
05-03-2021
Type of engine
What is super long stroke
Benifits of superlong stroke
Boiler blow down procedure
What is clarifier
What is purifier
How to change purifier to clarifier
Air compressor safeties
Location of bursting disc
Piston checks
Types of clearance where you will take and measuring instruments you will use
Where to take butt clearance
Working of flame eye
Ext: Subbarao
Fn 3
Type of ship(bulk)
Fire detection system X Working
Hose pipe
Some questions from construction forgot
ISM code in detail
Certificates to be carried
Fn 5
Open circuit test
IR
Safeties on switch board
Fn 3
Type of ship(bulk)
Fire detection system X Working
Fire fighting in case of fire
Collision bk regulation
Fire in purifier room
Hypermist working
Hose pipe
Fn 5
Open circuit test
IR
Safeties on switch board
Fun-4b
Type of engine
Vit n supervit
How to reduce sfoc
Wat will ur action when omd alarm comes
Ventilation system
Working of supervit mechanism
Fuel injection working
Nomenclature of bearing
Fun- 6
Where do u ll take boiler water test
Rest forgot
[3/22, 10:13 AM] Ms: 21-3-22
Subbarao
Ss gadkar
Motor mep
Type of engine
Explain ur engine
Piston calibration
Turbocharger
Welding rod
[3/24, 8:08 PM] Ms: Mumbai
24 March 2021
Internal- Subbarao
External- Ss gadkar
Safety
1. on Main Deck fire Line which devices are there?
Mep
1. How will you take tappet clearance?
2. Boiler water test and there values
3. how will you know piston is up during tappet clearance?
4. Where Does the Emergency Generator Supply Goes?
5. Aux engine Cylinder Head is removed and kept in workshop. Now how will you
overhaul cylinder head?
6. gauge glass overhaul
7. pilot burner overhaul
Safety
1.collison bulkhead regulation
2.corrugated bulkhead regulation
3.cargo hold regulation
4.cargo hold detector how works explain
External – S S Gadkar
Type of engine
What is peculiar about pipe that joins fuel pump to fuel valve
How will you know if it is leaking
MEP:
1) Types of stern tube
2) piston callibration and checks
3) oil in hotwell, action and reason.
COC
30.03.2022
Ext Subbarao Sir
Int. Ss gadkari
Func 3
1. What is Ism, How will you implement on your ship
2. Short Term DOC
3. What is Enclosed Space, procedure to enter, type of gas detection instrument
4. Shear Strake, Garboard Strake, Metacenter, Rightning lever, Center of Buoyancy
7. Safeties
8. Angle of Loll
Result- Pass
30.03.2022
7. Safeties
8. Angle of Loll
Result- Pass