Professional Documents
Culture Documents
124915-AJ Series Consumable Item (Nozzle and Lens) Lists (ENSIS-AJM2 Gen3 3kw Spec.) Rev.F
124915-AJ Series Consumable Item (Nozzle and Lens) Lists (ENSIS-AJM2 Gen3 3kw Spec.) Rev.F
124915-AJ Series Consumable Item (Nozzle and Lens) Lists (ENSIS-AJM2 Gen3 3kw Spec.) Rev.F
Nozzle*1*6
Type of nozzle Thickness Lens*5
Part name P/N Drawing Spec Material*4 Cutting
Shape I/D 3 kW 190
Mild steel, Zinc coated steel 0.8-1.2 Air cut ○
Mild steel, Zinc coated steel 0.8-2.6 Clean cut
NOZZLE (S2.0)*2 71501057 1576411B Single
SUS 0.5-1.5 Air cut
SUS 0.8-2.5 Clean cut
Standard 2.0 Brass 0.8-8.0 Clean cut
Plug Guide ASSY
Titanium 0.8-3.0 Clean cut
NOZZLE (D2.0F)*2 71570022 DA50776--D Double Alminum 0.8-2.0 Air cut
Alminum 0.8-3.0 Clean cut Contact Plate
Copper 0.8-3.0 O2 cut DAD0264---
NOZZLE (S1.0FE) *3 71570030 9010399 ECO Single ECO 1.0 Mild steel 1.0-9.0 ECO cut ○ P/N: 71571527
NOZZLE (S1.2FE) 71570023 9010403 ECO Single ECO 1.2 Mild steel 1.0-9.0 ECO cut ○
*7
NOZZLE (D1.2FE) 71568227 DA56095--- ECO Double ECO 1.2 Mild steel 12.0-16.0 ECO cut ○
NOZZLE (D2.0FE) New 71572665 DA50789--- ECO Double ECO 2.0 Mild steel 19.0-22.0 ECO cut ○
Mild steel 2.6-3.2 Clean cut
NOZZLE (D2.5) 71516789 1576398B Clean Double 2.5
SUS 2.5-3.0 Clean cut
NOZZLE (D2.5W) 71712335 9003351 WACS Double WACS 2.5 Mild steel 9.0-12.0 WACS cut ○
NOZZLE (D3.4FW) New 71572669 4694830--- WACS Double WACS 3.4 Mild steel 16.0-22.0 WACS cut
NOZZLE (D4.0W) 71712336 9003352 WACS Double WACS 4.0 Mild steel 16.0-25.0 WACS cut ○
Mild steel 0.8-4.5 Clean cut
NOZZLE (D4.0 CC) 71555121 1576280A Clean Clean 4.0
SUS 3.0-10.0 Clean cut ○
Mild steel 3.2-6.0 Clean cut Coupler Sensor Head
NOZZLE (D7.0 CC) 71574165 1576277--D Clean (Thick) Clean 7.0
SUS 2.5-15.0 Clean cut ○ 7973458--D
Alminum 3.0-12.0 Clean cut ○ P/N: 71574176
AL NOZZLE (D4.0 AL) 71501093 1577862 Clean (ALM) Clean 4.0 Titanium 4.0-5.0 Clean cut ○ (include Plug Guide ASSY)
Copper 4.0-6.0 O2 cut ○
*1 Above type of nozzles are listed in AJ cutting condition files. Other type of nozzles are not listed in AJ cutting condition files.
*2 When processing copper, brass, titanium or mirror surface material please be sure to use D2.0F nozzle, not S2.0.
*3 At ECO cut, please use the S1.2FE as much as possible. When using S1.0FE nozzle, please change the number of times of Pre-Gas to 20. PLUG
*4 Depending on the standard of the material, there may be no processing conditions. P/N: 71712350
*5 Do NOT use double nozzles except for D2.0F when using 150 mm focus length lens because laser beam may interferes.
*6 This table is EX specification. In EU, the Thickness range is bit different from EX.