Professional Documents
Culture Documents
DSL Electric QB
DSL Electric QB
1. What is Transformer?
a) Transformer is a device used to convert low alternating voltage to a high alternating voltage
b) Transformer is a device used to convert alternating current to direct current
c) Transformer is a device used to convert low alternating current to a high alternating current
d) Transformers are used only for low alternating voltage
Answer: a
Answer: a
Answer: b
Answer: b
Answer: c
Answer: c
Answer: a
Answer: d
Answer: c
Answer: d
Answer: b
Answer: a
15. What is the formula for the thickness of the ac machines?
a) thickness = 40 * inner diameter of frame/12
b) thickness = 40 + inner diameter of frame/12
c) thickness = 40 – inner diameter of frame/12
d) thickness = 40 * inner diameter of frame*12
Answer: a
16. What is the formula for the breadth of the ac machine?
a) breadth = 6 + 0.01 * inner diameter of frame
b) breadth = 6 – 0.01 * inner diameter of frame
c) breadth = 6 * 0.01 * inner diameter of frame
d) breadth = 6 / 0.01 * inner diameter of frame
Answer: a
17. What is the formula for the checking of rigidity of induction machines?
a) moment of inertia ≥ radius / length of stator core * 90
b) moment of inertia ≥ radius * length of stator core * 90
c) moment of inertia ≥ radius * length of stator core / 90
d) moment of inertia ≤ radius / length of stator core * 90
Answer: c
18. What is the formula for the radius at the centre of gravity?
a) radius at the centre of gravity = inner diameter1.5/6.3
b) radius at the centre of gravity = inner diameter2/6.3
c) radius at the centre of gravity = outer diameter1.5/6.3
d) radius at the centre of gravity = outer diameter2/6.3
Answer: c
a) centrifugal force = weight of revolving body * 39.43 * speed2 * radius of circular path
b) centrifugal force = weight of revolving body / 39.43 * speed2 * radius of circular path
c) centrifugal force = weight of revolving body * 39.43 / speed2 * radius of circular path
d) centrifugal force = weight of revolving body * 39.43 * speed2 / radius of circular path
Answer: a
20. The use of _____ instruments is merely confined within laboratories as standardizing instruments.
(a) absolute
(b) indicating
(c) recording
(d) integrating
(e) none of the above
Ans: a
21. Which of the following instruments indicate the instantaneous value of the electrical quantity being
measured at the time at which it is being measured ?
Ans: b
22. _____ instruments are those which measure the total quantity of electricity delivered in a particular
time.
(a) Absolute
(b) Indicating
(c) Recording
(d) Integrating
Ans: d
(a) Ammeters
(b) Voltmeters
(c) Wattmeters
(d) Ampere-hour and watt-hour meters
Ans: d
(a) wattmeters
(b) voltmeters
(c) ammeters
(d) ohmmeters and resistance bridges
(e) all of the above
Ans: d
Ans: d
27. A _____ device prevents the oscillation of the moving system and enables the latter to reach its final
position quickly
(a) deflecting
(b) controlling
(c) damping
(d) any of the above
Ans: c
28. The spring material used in a spring control device should have the following property.
Ans: e
Ans: e
30. A moving-coil permanent-magnet instrument can be used as _____ by using a low resistance shunt.
(a) ammeter
(b) voltmeter
(c) flux-meter
(d) ballistic galvanometer
Ans: a
Ans: c
32. Which of the following devices may be used for extending the range of instruments ?
(a) Shunts
(b) Multipliers
(c) Current transformers
(d) Potential transformers
(e) All of the above
Ans: e
(a) 10 A
(b) 30 A
(c) 60 A
(d) 100 A
Ans: d
34. For handling greater currents induction wattmeters are used in conjunction with
Ans: b
35. Induction type single phase energy meters measure electric energy in
(a) kW
(b) Wh
(c) kWh
(d) VAR
(e) None of the above
Ans: c
36. Most common form of A.C. meters met with in every day domestic and industrial installations are
Ans: c
37. Which of the following meters are not used on D.C. circuits
Ans: c
Ans: d
Ans: e
40.___ is an instrument which measures the insulation resistance of an electric circuit relative to earth
and one another.
Ans: b
42. The household energy meter is
Ans: c
Ans: a
Ans: a
Ans: c
46. An ammeter is a
Ans: a
Ans: a
Ans: c
Ans: a
Ans: a
(a) series
(b) parallel
(c) series-parallel
(d) none of the above
Ans: a
(a) linear
(b) non-linear
(c) either (a) or (b)
(d) neither (a) nor (b)
Ans: a
Ans: c
55. The resistance in the circuit of the moving coil of a dynamometer wattmeter should be
Ans: c
Ans: a
Ans: C
58. The pressure coil of a wattmeter should be connected on the supply side of the current coil when
(a) load impedance is high
(b) load impedance is low
(c) supply voltage is low
(d) none of the above
Ans: a
Ans: b
Ans: c
61. In a 3-phase power measurement by two wattmeter method, both the watt meters had identical
readings. The power factor of the load was
(a) unity
(6) 0.8 lagging
(c) 0.8 leading
(d) zero
Ans: a
62. In a 3-phase power measurement by two wattmeter method the reading of one of the wattmeter was
zero. The power factor of the load must be
(a) unity
(b) 0.5
(c) 0.3
(d) zero
Ans: b
63. The adjustment of position of shading bands, in an energy meter is done to provide
(a) friction compensation
(b) creep compensation
(c) braking torque
(d) none of the above
Ans: a
64. An ohmmeter is a
Ans: b
65. When a capacitor was connected to the terminal of ohmmeter, the pointer indicated a low resistance
initially and then slowly came to infinity position. This shows that capacitor is
(a) short-circuited
(b) all right
(c) faulty
Ans: b
Ans: c
(a) battery
(b) permanent magnet D.C. generator
(c) AC. generator
(d) any of the above
Ans: b
(a) spring
(b) gravity
(c) coil
(d) eddy current
Ans: c
(a) 6 V
(b) 12 V
(c) 40 V
(d) 100 V
Ans: d
Ans: c
Computers
71. Who is the father of Computers?
a) James Gosling
b) Charles Babbage
c) Dennis Ritchie
d) Bjarne Stroustrup
Answer: b
Answer: d
Answer: d
Answer: c
Answer: c
76. Which of the following computer language is written in binary codes only?
a) pascal
b) machine language
c) C
d) C#
Answer: b
Answer: a
Answer: a
80. Which of the following unit is responsible for converting the data received from the user into a
computer understandable format?
a) Output Unit
b) Input Unit
c) Memory Unit
d) Arithmetic & Logic Unit
Answer: b
81. Which of the following monitor looks like a television and are normally used with non-portable
computer systems?
a) LED
b) LCD
c) CRT
d) Flat Panel Monitors
Answer: c
Answer: a
83. Which of the following part of a processor contains the hardware necessary to perform all the
operations required by a computer?
a) Controller
b) Registers
c) Cache
d) Data path
Answer: d
85. Which of the following device use positional notation to represent a decimal number?
a) Pascaline
b) Abacus
c) Computer
d) Calculator
Answer: b
Answer: b
Answer: a
88. Which of the following defines the assigned ordering among the characters used by the computer?
a) Accumulation
b) Sorting
c) Collating Sequence
d) Unicode
Answer: c
89. Which of the following storage is a system where a robotic arm will connect or disconnect off-line
mass storage media according to the computer operating system demands?
a) Magnetic
b) Secondary
c) Virtual
d) Tertiary
Answer: d
90. Which of the following is known as the interval between the instant a computer makes a request for
the transfer of data from a disk system to the primary storage and the instance the operation is
completed?
a) Disk utilization time
b) Drive utilization time
c) Disk access time
d) Disk arrival time
Answer: c
91. Which of the following devices provides the communication between a computer and the outer
world?
a) Compact
b) I/O
c) Drivers
d) Storage
Answer: b
92. Which of the following are the input devices that enable direct data entry into a computer system
from source documents?
a) System Access devices
b) Data acquiring devices
c) Data retrieving devices
d) Data Scanning devices
Answer: d
93. Which of the following is the device used for converting maps, pictures, and drawings into digital form
for storage in computers?
a) Image Scanner
b) Digitizer
c) MICR
d) Scanner
Answer: b
Answer: a
95. Which of the following is known as the language made up of binary-coded instructions?
a) High level
b) BASIC
c) C
d) Machine
Answer: d
96. Which of the following package allows individuals to use personal computers for storing and
retrieving their personal information?
a) Personal assistance package
b) Graphics package
c) Spreadsheet package
d) Animation package
Answer: a
97. Which of the following is created when a user opens an account in the computer system?
a) SFD
b) MFD
c) Subdirectory
d) RFD
Answer: c
98. Which of the following is a technique that marked the beginning of computer communications?
a) User Environment
b) Batch Environment
c) Time Sharing
d) Message passing
Answer: c
99. Which of the following is a type of technique in which dumb terminals are connected to a central
computer system?
a) Time Sharing
b) Message passing
c) Batch environment
d) User environment
Answer: a
100. Which of the following service allows a user to log in to another computer somewhere on the
Internet?
a) e-mail
b) UseNet
c) Telnet
d) FTP
Answer: c
101. Which of the following is not a type of computer on the basis of operation?
a) Digital
b) Analog
c) Hybrid
d) Remote
Answer: d
102. Which of the following type of computer is mostly used for automatic operations?
a) analog
b) digital
c) hybrid
d) remote
Answer: c
103. Which of the following invention gave birth to the much cheaper microcomputers?
a) PDAs
b) Microprocessors
c) Microcomputers
d) Mainframes
View Answer
Answer: b
104. Which of the following computers are lower than mainframe computers in terms of speed and
storage capacity?
a) Mainframes
b) Hybrid
c) Mini
d) Super
Answer: c
Answer: d
Mechatronics
106 . Where and when was the word Mechatronics invented?
a) Japan(1960)
b) Japan(1980)
c) Europe(1960)
d) Europe(1980)
Answer: a
Answer: d
Answer: b
Answer: a
Answer: b
111. Which among the following carry out the overall control of a system?
a) Graphical display
b) Sensors
c) Actuators
d) Digital controls
Answer: d
Answer: a
Answer: b
114. What converts physical input into output, among the basic parts of a measuring system?
a) Transducer or sensor
b) Signal conditioning
c) Intelligence
d) Display
Answer: a
115. The analog to digital conversion in a measurement system takes place inside _____
a) transducer
b) signal processor
c) display
d) led
Answer: b
Answer: b
Answer: a
118. Which type of error always has the same and consistent value?
a) Random errors
b) Systematic errors
c) Zero errors
d) Hysteresis errors
Answer: b
119. The largest value for which the instrument output remains zero is ____
a) hysteresis error
b) resolution
c) sensitivity
d) dead zone
Answer: d
Answer: a
121. Which elements among the following is used to modify the data before display?
a) Data presentation element
b) Data transmission element
c) Data processing element
d) Variable manipulation element
Answer: c
122. Which is the first aspect which needs to be considered in the Mechatronics design process?
a) Hardware design and simulation
b) Conceptual design
c) Mathematical modelling
d) Modelling and simulation
Answer: d
123. In the level of integration of Mechatronics system, an example of the first level is _____
a) fluid valves
b) automatic machine tools
c) industrial robots
d) microprocessors
Answer: a
124. What is the role of the second level in the mechatronics system design?
a) Integrates microelectronics into electrically controlled devices
b) Integrates electrical signal with mechanical action
c) Advanced control strategy level
d) Providing artificial intelligence
Answer: a
Answer: c
Answer: a
128. What is the function of “analysis” in the modelling and simulation phase?
a) Database for maintaining project information
b) Sub models for eventual reuse
c) Contains Numerical methods
d) To produce high-level source code
Answer: c
129. Describing the behaviour characteristics through block diagram is done in ____
a) modelling and simulation
b) prototyping
c) deployment
d) design optimization
Answer: a
Answer: b
Answer: c
132. The depth that the tool is plunged into the surface is called as ______
a) feed
b) depth of cut
c) depth of tool
d) working depth
Answer: b
Answer: a
Answer: c
135. In CNC systems multiple microprocessors and programmable logic controllers work ______
a) in parallel
b) in series
c) one after the other
d) for 80% of the total machining time
Answer: a
Answer: d
137. In how many ways CNC machine tool systems can be classified?
a) 2
b) 3
c) 4
d) 5
Answer: b
Answer: a
Answer: a
143) Pre lubrication is required if an engine that has been shut down for
more than--- hours ( a )
144) The purpose of Turbo lube pump in WDP4 Locomotive before cranking is ( c )
a) To lubricate the Turbo b)To remove the residual heat c)To lubricate turbo bearing d)To
lubricate crank shaft
145) Turbo lube pump should be running for ____minutes after engine is shutdown if engine was
running at 5th notch and higher for 60minutes prior to engine shut down.( b )
146) What is the Safety Device provided in the Lube oil system ? ( c )
149) From where the control air pressure will get air pressure ( b )
a)MR2 b)MR1 c)BKTs d)J filter
150) Main Reservoir (compressed air pressure) Unloading will takes place at_kg /cm2 ( c )
a)MR Safety valve b)MR2 c) Cooling Coil d)3 / 4" cutout cock
155) Manual Sanding is cutout when the locomotive is operating in power/wheel creep mode, and
moving at speeds above ( c )
a)30kmph b)10kmph c)19.5 km/h d)15kmph
a) 95 b) 92 c) 85 d) 100
160) In HHP loco the system maintains the coolant temperature within a predetermined range from
( a )
a)79° C to 85° C b) 85 to 95° C c) 92 to 100 ° C d) 72 to 80 ° C
161) What is the indication for blown radiator fan fuse? ( c )
a)LED b)Buzzer c)Fuse blown out Indicator will project out d)Message
162) Hot engine alarm ( HEA) will come at _____°Cin WDG3A locos ( c )
a) 60 b) 70 c) 90 d) 80
163) During one of the following occasions Hot engine alarm indication will get ( c )
a) Continuous 8th notch working b) Excess load
c) Water pump not working d) Full water in expansion tank
a) Water left side return header b) Water expansion tank c) Water right
side return header d) All the above
a) Fail the locomotive b) Work the train by reducing 10% speed from Booked speed c) Work
further with 50 kmph d) Ask for the relief engine
167) The speed restriction that has to be observed by a LP when headlight of engine
fails on BG is __________ kmph. ( c )
168) Whenever stopped on gradient for any reason it is essential to apply the ______ brakes
( c )
169) How much pressure should be ensured in the engine and BV before staring
air brake train ? ( c )
a) 6cm2kg,4.9 kg/cm2 b) 5.2kg/cm2, 4.7 kg/cm2 c) 5kgcm2, 4.8
kg/cm2 d) 4.8kg/cm2, 5kg/cm2
170) For any reason, a train is brought to a stand, the hand brakes of Locomotive
and formation shall be applied if stoppage is more than ( d )
172) The following shall not be used for extinguishing fires on electrical equipment. ( c )
a)60, 8 and 8 seconds b)60,17 and 17 seconds c)170, 17 and 17 seconds d)65,8
and 8 seconds
174) What combination of trains are Permitted for running long haul train? ( d )
a)Empty/Empty b)loaded/Empty c)Loaded/Loaded d)All the above
176) What precaution should be taken for conducting Air brake self test in GM locos? ( d )
a) Secure loco
b)Secure formation
c)Detach loco and secure
d)Secure both, close BP & FP COC of loco towards formation.
177) What should be done first for changing console in WDG 4 / WDP 4 locos ? ( a )
a)Disable working control stand & enable non working control stand
b)Enable working control stand & disable non working control stand
c)As per convenience
d)None of the above
178) When Head light become defective speed of the train shall not exceed ____.( c )
180) During engine starting if engine is cranking, Firing, Over speeding, OSTA Tripping and Engine
shutting down the reason may be ( b )
a) apply A-9 brake b) apply SA-9 and Dynamic Brakes c) apply Hand brakes d) close the
throttle to zero.
183) Locos provided with Cast Iron brake blocks requires ______than the Locos provided with
Composite brake blocks ( a )
a)More braking distance b)Less braking distance c)frequent change of brake blocks d)BC
pressure 3.8 kg/cm2
184) If train stopped in mid section on account of Loco Failure Loco pilot should do
____________immediately ( b )
a)Inform TLC/PCOR b)Put on Flasher Light, Apply A-9,SA-9, wooden wedges and secure formation.
c)Ask for relief Loco d)Attend the Locomotive
a)60, 8 and 8 seconds b) 60,17 and 17 seconds c)170, 17 and 17 seconds d)65,8
and 8 seconds
a)To control the train and to maintain constant speed at PSR ,TSR and Loop lines b)To
nullify the conjunctional brakes c)To stop the train d) none
187) While TOC of Loco, If Flasher light glows but does no blink, what action would
you take. ( a )
a) Fail the loco b)Will work to nearest shed c)Change the bulb d)Work normally
188) After which check/restriction, non derailed vehicles of a train involved in accident be allowed for
on-ward journey ( b )
a) Without check b) After certified by TXR c)With 10% less speed d)80 KMPH
189) What immediate action would you take on noticing sudden drop of BPpressure/vacuum on run ?
( c )
a) Stop the train b) Contact Guard on VHF c) Switch on Flasher light d)Inform PRC
190) When Head light becomes defective speed of the train shall not exceed ? ( c )
191) What should be done by LP for releasing proportional loco brakes during
A9 application ? ( c )
a) Direct brake application b) Conjunctional brake application c) Formation brakes d) Both B and C
196) If battery ammeter is showing over charging, what may be the reason? ( c )
197) If BA shows over charging due to defective battery, the following action is to
be taken? ( a )
a) BS to be open b) Shut down the engine
c) Engine to be brought to idle d) No action required
198) If battery ammeter shows over charging, what may be the reason? ( c )
a) BS open b) MB1 tripped c) VRP defective d) AGFB tripped
199) If BA shows over charging due to defective VRP, the following action is to be
taken? ( a ) a) AGFB off b)
Shutdown the Engine c) Idle d) No action required
a) AGFB Tripped b) VRP Fuse Blown out c) Cards Slack(BX ,BN) d) All
209) If engine is not cranking which power contactor interlocks are to be checked?( a )
a) P22, S1 b) P22, S21 c) P21, S1 d) P1, S1
210) For engine cranking what should be MUSD & ECS position? ( b )
211) If FPC Contactor closing but engine is not cranking what may be the reason?( c )
213) If engine is cranking but not firing with indication what may be the reason?( a )
214) If engine is cranking but not firing while starting what may be the reason? ( d )
a) FPM not working b) Fuel Booster Pump defective c) Love joy coupling defectived) All the
above
216) What is the reason if engine is cranking, firing but not holding? ( d )
a) SAR Interlock defective b) OPS Defective c) Lube oil system defective (Below 1.6Kg/Cm d) All the
above
a) MB2 Tripped b) MFPB1 &MFPB2 Tripped c) FPB Tripped d) All the above
a) MB1 b) MCB1 & MCB2 Tripped c) FPB Tripped d) All the above
221) What is the reason if engine shutdown without any indication on run
in GE Governor? ( a )
a) Engine shutdown b) Engine comes to idle c) Load meter shows zero d) No Problem
a) AFL Operates b)Engine idle with full brakes c)Only loco brakes get applied d)No
effect
a) SW1 & SW2 b) SP1 & SP2 c) MCB1 & MCB2 d) MFPB1 & MFPB2
230) To reset only Buzzer what is the action required by the Driver? ( c )
a) SW1 &SW2 b) SP1 &SP2 c) Switch On normal flasher light and SW1&SW2 Off d) All the
above
a) SW1 &SW2 b) SP1 & SP2 c) MCB1 & MCB2 d) MFPB1 & MFPB2
a) Tampering of pressure switches b) 171 Wire disconnection c) Pack DMR d) Fail the loco
a) BP For 5Kg/Cm b) MR For 9.5Kg/Cm c) Control air pressure for 5Kg/CM d) FP For
6Kg/Cm
240) If engine is running with Hot engine alarm which safety device is operated?( c )
a) Load meter zero b) Engine comes to Idle c) GR Indication with bell d) All the
above
245) In AC/DC Locos during cranking which relay protects Auxiliary And
Exciter Generators? ( c )
246) In place of AC Governor, which Governor is provided for compressor loading and unloading
( a )
a) EPG b) GE c) Z.W d) Run-Release
a) 1 b) 2 c) 3 d) 4
249) which circuits are protected by GR1 & GR2 after ear thing? ( c )
250) what are the changes in single BKT Locomotives as compare to Double
BKT Loco’s? ( d )
254) If BKT or Reverser is not operating properly what is the action to be taken?( b )
a) Fail the loco b) Operate manually with `L’ rod c) Shutdown engine d) Engine Idle
a) 3.5 b) 5 c) 6 d) 8
a)12 b) 24 c) 36 d) 16
268) Pinion to Bull gear ratio in WDM3A loco is ________ ( b )
a)18:74 b) 18:65 c) 17:77 d) 17:90
269) In WDM3A loco FTTM is driven with ________ ( b )
a)Belts b) Gear c) Hydraulic pressure d) Electric motor
270) In WDM3A loco RTTM is driven with ________ ( a )
a)Belts b) Gear c) Hydraulic pressure d) Electric motor
271) Type of transmission in WDM3A loco ( b )
a)DC-AC b) AC-DC c) DC-DC d) AC-AC
a)5 b) 2 c) 3 d) 4
281) In Alco loco fuel oil regulating valve is set at ____ kg/cm² ( b )
a)3 b) 4 c) 5 d) 6
282) In Alco loco lube oil relief valve is set at ____ kg/cm² ( d )
a)6 b) 7 c) 8 d) 9
a)86 b) 76 c) 96 d) 68
391. MR safety valve is set at ______ kg/cm² ( d )
a)8 b) 8.5 c) 10 d) 10.5
a)5 b) 6 c) 7 d) 8
290) In Alco loco, if water level comes down below 1” from bottom of tank ____ safety device will
operate ( c )
291) Wheel numbers to which brake blocks get applied when hand brake is applied in
WDG3A loco ( b )
a)L1,L2 b) R1,R2 c) L1,R1 d) L2,R2292)
292) Dust exhaust motors are available for ______ type of filters ( b )
a)AC to DC b) DC to AC c) DC to DC d) AC to AC
a)AC to DC b) DC to AC c) DC to DC d) AC to AC
a) Water b) Oil & waterc) Super charged air & Water d) None
a)4 b) 8 c) 10 d) 12
307) In Alco loco fuel oil relief valve is set at ____ kg/cm² ( a )
a) 5 b) 2 c) 3 d) 4
308) In Alco loco fuel oil regulating valve is set at ____ kg/cm² ( b )
a) 3 b) 4 c) 5 d) 6
a) 86 b) 76 c) 96 d) 68
a) 8 b) 8.5 c) 10 d) 10.5
311) In Alco loco EPG is located in ______ ( c )
313) In Alco Traction Motor gear case is having ___ no. of bolts ( c )
a)5 b) 6 c) 7 d) 8
315) In Alco loco, if water level comes down below 1” from bottom of tank _________ safety device
will operate ( c )
a)AC to DC b) DC to AC c) DC to DC d) AC to AC
a)AC to DC b) DC to AC c) DC to DC d) AC to AC
a)60 b) 70 c) 90 d) 80
a)10 b) 8 c) 12 d) 10.5
a) MR1 b) MR2c) FP d) BP
330) Fuel pump motor is not working though all circuit breakers are switched ‘ON’, the reason may
could be ________. ( d )
336) In Twin beam head lights __ volts halogen lamps are used ( c )
a)72 b) 32 c) 24 d) 20
337) In twin beam head light system in DC-DC converter if one unit is defective the stand by unit can be
brought into function by ( a )
339) In MCBG loco when shut down occurs due to over speed
a) Fail the loco b) Lock rack of L5 c) lock left side racks d) Ignore
553. If battery ammeter is showing over charging, what may be the reason? ( c )
a) BS open b) MB1 tripped c) Battery defective d) AGFB tripped
555. If battery ammeter shows over charging, what may be the reason? ( c )
a) BS open b) MB1 tripped c) VRP defective d) AGFB tripped
560. If BA ammeter shows discharging and not rectified what is the action to be taken?( d )
a)Work for 4 Hours b) Do not Shut down
c)Do not allow for Automatic Shut Down d) All of the above
564. If engine is not cranking which switch is to be checked on the front panel? ( c )
a) Battery Switch b) MUSD c) ECS d) G.F.Switch
567. For engine cranking what should be MUSD & ECS position? ( b )
a)RUN, RUN b) RUN, IDLE c) STOP, RUN d) STOP,IDLE
568. If FPC Contactor closing but engine is not cranking what may be the reason? ( c )
a) MB1 Tripped/Off b) MB2 Tripped/Off
c) FPB Tripped/Off d) MFPB1 & MFPB2Tripped/Off
569. If engine is cranking but not firing what may be the reason? ( d )
a) OPS1 Stuck up b) LWS Operated c) OSTA Tripped d) All the above
570. If engine is cranking but not firing with indication what may be the reason? ( a )
a) LWS Operated b) OSTA Tripped c) SAR Defective d) All the above
571. If engine is cranking but not firing while starting what may be the reason? ( d )
a) FPM not working b) Fuel Booster Pump defective
c) Love joy coupling defectived) All the above
573. What is the reason if engine is cranking, firing but not holding? ( d )
a) SAR Inter lock defective b) OPS Defective
c) Lube oil system defective (Below1.6Kg/Cm2) d) All the above
574. What is the reason if engine shutdown automatically on run? ( d )
a) MB2 Tripped b) MFPB1 &MFPB2Tripped c) FPB Tripped d) All the above
585. To reset only Buzzer what is the action required by the Driver? ( c )
a) SW1 &SW2 b) SP1 &SP2
c) Switch On normal flasher light and SW1&SW2 Off d) All the above
591. If Head light fails what is the action to be taken by the Drivers? ( b )
a) Fail the loco b) Follow G&SR Rules
c) Work with classification lights d) Work normally
592. If engine shuts down with hot engine alarm which safety device operates? ( b )
a) ETS b) LWS c) SAR d) OPS
593. If engine is running with Hot engine alarm which safety device is operated? ( c )
a) LWS b) OPS c) ETS d) SAR
598. In AC/DC Locos during cranking which relay protects Aux and Exc. Gens? ( c )
a) SAR b) GR c) TDR d) WSR
662. Which circuits are protected by GR1 & GR2 after earthling? ( c )
a) Power Circuit b) Control circuit c) Power and Control circuits d) Nothing
663. What are the changes in single BKT Locomotives as compare to Double BKT Loco’s?( d )
a) 3BKR Relays b) P22 & P32 Contactors location interchanged
c) During DB 5Power contactors will energize d) All the above
666. If BKT or Reverser is not operating properly what is the action to be taken? ( b )
a) Fail the loco b) Operate manually with `L’ rod c)Shutdown engine d) Engine Idle
668. While working LE's Loco pilot should check and ensure __ before starting. ( c )
a) Head light b) Flasher Light
c) Brake Power physically and not moving of Loco up to 2nd Notch on application of SA-9
d) Marker Lights
670. When Head light become defective speed of the train shall not exceed ? ( c )
a) 20kmph b) 30kmph c) 40kmph d) 50kmph
671. What should be done by LP for releasing proportional loco brakes during ( c )
A9 application?
a) Pressing BKIV foot pedal b) Application of DB c) Either A or B d) None
677. Side load pads are provided in this type of under truck ( b )
a) Tri mount bogie b) Fabricated bogie c) HTSC bogie d) both b and c
688. If radiator fan is not working during continuous hot engine alarm switch ON ( a )
a) ERF b) LWS c) DMR d) TR A
693. In M.U. operation if trailing loco ¾" coc alone kept in open position ( d )
a) BP will not destroy in any position b) BP will destroy only in emergency position
c) Loco brakes will not apply d) BP will not create to 5 kg/cm2
708. In Medha Microprocessor loco if TM2 & 5 are isolated loco will start with ( a )
a) Series-parallel combination b) Parallel combination
c) Parallel with shunt combination d) Series-parallel with shunt combination
709. Engine should not be cranked if it is shut down for more than ( c ) a)
24 hrs. b) 16 hrs. c) 48 hrs. d) 32 hrs.
710. If MCBG power breaker is in OFF position during cranking engine will ( b )
a) not Crank b) not Fire c) not Hold d) a and b
717. In single BKT/Rev Loco during DB which power contactors will not pick up?( d )
a) P2 & P22 b) S21 &S31 c) S1, S21 & S31 d) Both a and b
720. In GE governor loco during cranking if MUSD is in stop position engine will ( d )
a) Crank b) Not fire c) Not hold d) Not crank
721. In WW governor loco not provided with MUSDR relay during cranking if ( b )
MUSD is in STOP position during cranking engine will
a) Crank b) Not fire c) Not hold d) Not crank
733. HP of WDP1 is ( d )
a) 1400 b) 1800 c) 2400 d) 2300
748. What is the Safety Device provided in the Lube oil system? ( c )
a) GFOLR b) OSTA c) LLOB d) LWS
751. From where the control air pressure will get air pressure_______ ( b )
a) MR2 b) MR1 c) BKTs d) J filter
752. MR (compressed air pressure) Unloading will takes place at _____kg /cm² ( c )
a) 8 b) 9 c) 10 d) 11
755. During one of the following occasions Hot engine alarm indication will get ( c )
a) Continuous 8thnotch working b) Excess load
c) Water pump not working d) Full water in expansion tank
757. During one of the following occasions Hot engine alarm indication will get ( c )
a) Continuous 8thnotch working b) Excess load
c) Water pump not working d) Full water in expansion tank
758. LWS is connected to ( b )
a) Water left side return header b) Water expansion tank
c) Water right side return header d) All the above
762. The following shall not be used for extinguishing fires on electrical ( c )
equipment.
a) dry chemical powder b) foam c) water d) none of these
764. What combination of trains are Permitted for running long haul train ? ( d )
a) Empty/Empty b) loaded/Empty c) Loaded/Loaded d) All the above
766. While taken over charge of Loco, if Flasher light glows but does not ( a )
flash/blink, what action would you take?
a) Fail the loco. b) Will work to nearest shed
c) Inform PRC & work further. d) Work normally
767. What precaution should be taken for conducting Air brake self test in GM ( d )
locos?
a) Secure loco b) Secure formation
c) Detach loco and secure d) Secure both & don’t detach from formation.
768. What should be done first for changing consol in WDG 4 / WDP 4 locos ? ( a )
a) Disable working control stand & enable nonworking control stand
b) Enable working control stand & disable nonworking control stand
c) As per convenience
d) None
777. In WDP4/WDG4 loco if LLOB is in tripped position during cranking engine will ( d )
a) Crank b) Not Fire c) Not hold d) Not crank
779. In WDP4/WDG4 banker loco working C/S, L/T switch should be kept in ( c )
a) Lead b) Trail c) HLPR d) Test
787. In WDP4/WDG4 when continuous wheel slip is experienced due to locked axle ( c )
a) Isolate the defective TM b) Isolate the defective speed sensor
b) Fail the loco immediately d) Isolate the defective truck
788. In WDP4/WDG4 loco while conducting BP leakage test. L/T switch should ( d )
be kept in
a) Lead b) Trail c) Helper d)Test
790. In WDP4/WDG4 loco while conducting BP leakage test L/T switch should ( c )
be kept in
a) Lead position b) Trail position c) Test position d) Helper
796. ____is the main power supply of CCB for the CCB system. ( b ) a)
DCU b)VCU c) PCU d) DVR
797. Brake cylinder pressure maximum is ___Kg/Cm2 during backup system ( a ) a)
3.8 b) 3.2 c) 2.2 d) 5
798. CCB fault code for Brake Pipe Leakage Failure ____________ ( c ) a) 6A b)
6C c) 6B d) 6D C
799. Emergency brake application is accomplished by_______ valve provided at the lower left of
each console ( a )
a)D 1 emergency valve b) Independent brake valve
c) Direct Brake valve d) companion emergency brake
801. The air brake system, trips locomotive control system whenever
______relay initiates a safety control or emergency air brake application. ( a )
a) PCR b) DMR c) WSR d)SR
802. The EM2000 reads main reservoir air pressure from ______ transducer. ( d ) a) BPT
b)BCT c) ERT d) MRPT
803. What is the code for Brake pipe control failure in self test ? ( b ) a)
8A b) 6A c)10A d) 22A
804. What is the code for Brake pipe leakage failure in self test? ( a ) a) 6B
b) 10B c)6F d) 6S
805. What is the function of KE valve in CCB system in WDPG4 Loco motive ? ( a ) a)
provides pneumatic back Up b) Creation of BP
c) Creation of FP d) Emergency application
806. Why Maximum of 5.2kg/cm2 brake cylinder pressure is used in place of
3.5kg/cm2 as in conventional locos ? ( c )
a) High horse power loco b) Speed is more c) A single shoe system is used d)
To have effective brake power
810. Do not crank engine for more than _____with starting motors in HHP. ( d ) a)
30seconds b) 1minutes c) 10seconds d) 20 seconds
825. If the LR % is______EM2000 is reducing power output because the engine's capabilities are
less than the load being requested. ( b )
a) less than 200 b) less than 100 c) 100 More than d) 100 less than 500
826. If the TM temperature is greater than _____degree Celsius the inverter will
De-rate to keep the traction motor temperature in control ( a )
a) 200 b) 100 c) 95 d)92 `
830. Shutting down of all diesel engines in a consist is accomplished ___ relay ( c ) a)
DMR b) GCR c) SDR d) FLR
831. TCC1 COMPUTER breaker provides power and protection to ( b )
a) GTO1 b) The No.1 bogie traction inverter (TCC1) computer and associated circuits
c) TM1 d) DCL
837. Whenever DC link exceeds 3600volts,the ____ trips, which fires a Hard
Crowbar. ( b )
a) AC control b) TCC Break Over Diode (BOD)
c) Local control breaker d) GR
838. Whenever DC link voltage exceeds 3200 volts ,the TCC fires a ___ crow bar( c )
a) Hard Crowbar b) Sneaky crow bar c) Soft Crowbar d) GR
839. How many Power Contactors are available in WDG4 Locomotive? ( d )
a) 7 b) 9 c) 8 d) 0
841. What is the maximum permissible speed of (designed for) WDG4 locomotives( b )
a) 150kmph b) 120kmph c)100kmph d)75kmph
844. The purpose of Turbo lube pump in WDP4 Locomotive before cranking is ( c ) a) To
lubricate the Turbo b) To remove the residual heat c) To lubricate
turbo Bearing d) To lubricate crank shaft
845. Turbo lube pump should be running for ______minutes after engine is shutdown if engine
was running at 5th notch and higher for 60minutes prior to engine shut down. ( b )
a) 15 b) 35 c) 20 d) 45
851. The EM2000 will consider a temperature probe failed if it reads _________ ( b )
a) Less than -155 degrees C or greater than 150 degrees C
b) Less than -55 degrees C or greater than 150 degrees C
c) More than -55 degrees C or greater than 150 degrees C
d) Less than -55 degrees C or greater than 250 degrees C
854. What precaution should be taken for conducting Air brake self test in GM locos?( d )
a) Secure loco b) Secure formation c) Detach loco and secure
d) Secure both, close BP & FP COC of loco towards formation.
855. What should be done first for changing console in WDG 4 / WDP 4 locos ? ( a )
a)Disable working control stand & enable non working control stand
b) Enable working control stand & disable non working control stand
c)As per convenience d) None
856. AGFB Stands for ( b )
a) MR1 b) MR2 c) BP d) FP
b) MR1 b) MR2 c) BP d) FP
a) 120 b) 40 c) 60 d) 30
a) 2 b) 1 c) 3 d) None
890. During engine starting do not hold the fuel prime/engine start switch (FP/ES) to ES position for
more than ____ sec. ( a )
a) 20 b) 30 c) 60 d) 80
891. Backlash to be maintained between ring gear and starter motor pinion ( c )
a) 0.008”-0.016” b) 0.007”-0.025” c) 0.015”-0.040” d) 0.020”-0.030”
965. WDP4D is a ( b )
a) Single cab loco b) Dual cab loco
c) Dual cab loco with disc brake d) Dual cab loco with Hotel load
982. Which of the following sensor are fitted in the traction motor? ( a )
a) Temperature sensor b) Voltage sensor
c) Air Pressure sensor d) All of the above
984. Which of the following changes are done during conversion from ( d )
4000 HP to 4500 HP
a) 54” Radiator fan is introduced instead of 52” radiator fan
b) 8th notch engine rpm is increased from 904 rpm to 954 rpm
c) OSTA tripping rpm is increased from 1035 to 1085
d) All of the above
996. During cranking of engine in cold condition, engine rpm not hold due to ( c )
a) Improper adjustment of governor compensation needle valve
b) Worn out Teflon seal of power piston
c) Both a & b
d) None of the above
1013. Clearance between flywheel ring gear teeth and EPU must be a gap of ( b )
a) 0.020”± 0.005”b) 0.025” ± 0.005” c) 0.030” ± 0.005” d) 0.035” ± 0.005”
1017. How will you check the working of soak back pamp? ( d )
a) After engine shut down & by opening no.1 oil pan hand hole cover
b) After engine shut down & by opening no.8 oil pan hand hole cover
c)After engine shut down & by opening no.9 oil pan hand hole cover
d)After engine shut down & by opening no.16oil pan hand hole cover
1023. Don’t shift the ISOLATION Switch to run position immediately after engine start, ( a )
otherwise Engine will shut down due to
a )EPD low water button & LLOB operation. b) EPD crankcase button & LLOB operation
c)Only LLOB operation. d) None of the above
1025. Gap between TM blower intake ring and blower wheel on both sides of wheel ( b )
assembly i.e.MA/TM is
a) 2.5 to 5 mm b) 3.5 to 5mm c) 4.5 to 5mm d) none of the above
1031.WDG4DD is a ( c )
a)single cab loco b) Duel cab loco
c) Duel cab loco with disc brake d) Duel cab loco with Hotel load
1033. In HHP MU, loading & unloading of compressor of both loco is synchronized by ( c )
a) MVCC of leading loco b) MVCC of trailing loco
c) CMPSYN d) None of the above
1034. In HHP MU ( d )
a) Loading of compressor of both loco is occurred at same pressure
b) Unloading of compressor of both loco is occurred at same pressure
c) Loading & unloading of compressor of both loco is occurred at same pressure
d) Loading & unloading of compressor of both loco is occurred at different pressure
1036. Which of the following NDT process is used for auxiliary generator drive shaft testing
( a )
a) ZYGLO testing b) MPT c) UST d) None of the above
1037. In which schedule height is cattle guard & rail guard is measure and recoded? ( b )
a) T-30 & above b) T-90 & above c) T-180 & above d) 3Yeatly & above
1039. How many magnetic poles are in radiator fan when run in full speed? ( a )
a) 8pole b) 12pole c) 16pole d) None of the above
1042. Which of the following sensor is not fitted in the traction motor? ( c )
a) Current sensor b) Speed sensor c) Air pressure sensor d) All of the above
1045. Which of the following component are recently fitted in HHP Locomotive ( d )
a ) APU b) MCBG c) CREDI d) All of the above
1047. Epicyclic gear trains are used in HHP Locomotive TSC. Advantage of Epicyeclic ( a )
gear trains is to
a) Obtain high velocity ratio in comparatively lesser space
b) Obtain the desired direction of motion of drive gear
c) Transmit power when the distance between the two gear is large
d) None of the above
1048. Function of EPU is to ( d )
a) Measure the rpm of engine crankshaft.
b) Protect the engine crank shaft from damage due to hydraulic lock.
c)Limits the cranking speed to approximately 30rpm during the first engine crankshaft
revolution.
d) All of the above
1049. During EPD testing if throttle is above third notch then shut down will occur in ( d )
a ) Approximately 60 seconds. b) Approximately 40 seconds.
c) Approximately 35 seconds. d) Approximately 02 seconds.
1057. How many magnetic poles are connect in radiator fan circuit when run slow speed? ( c )
a) 8pole b) 12pole c) 16pole d) None of the above
1064. There are how many batteries are fitted in WDG4D Locomotive? ( b)
a) 2 b) 8 c) 10 d) none of the above
1072. In MEDHA control system when turbo cool down cycle is running, radiator ( a )
fan will drop at
a) Below 73oc b) Below 79o c c) Above 85oc d) 96oc
1077. In WDG4/WDP4 loco while conducting BP leakage test L/T switch should
be kept in ( c )
a) Lead position b) Trail position c) Test position d) Helper position
1083. During EPD testing at idle engine should not be shut down before ( d )
a) 120 seconds b) 50 seconds c) 60 seconds d) 35 seconds
1084. TPU is fitted on ( b )
a) Harmonic damper b) TSC c) Main Alternator d) Companion alternator
1088. During EPD testing (engine running above 3rd notch) engine should be shutdown in( d )
a) 120 seconds b) 40 seconds c) 35 seconds d) immediately
1106. Normal air box pressure (BAP) in HHP Locomotive at full speed & full load is ( c )
a) 1.1kg/cm2-1.75kg/cm2 b) 1.5kg/cm2-1.95kg/cm2
c) 1.4kg/cm2-1.75kg/cm2 d) 1.4kg/cm2-1.50kg/cm2
1201) In WAG7/WAP4 locos QLM is set at ... Amps of feeding power circuit.
1202) To close all line contactors, position of EP1 & EP2 COCs in WAG7 is..
Answer: (B)
1203) Location of duplex check valve in WAG5, WAG7 & WAM4 loco is a
a) Before MR-3 b) Cab-1 left side locker c) After MR-4 d) Pneumatic panel
Answer: (A)
1204) Location of C2A relay valve inWAG-5, WAM4 & WAG7 (u p to 27199) is at
a) Behind BA box no.3b) Behind BA box no.2
c) Behind BA box no.1 d) Behind BA box no.4
Answer (A)
1205) Location of C2A relay valve in WAG-7 loco 27200 onwards & WAP4 crew friendly cab locos is
at…
a) Behind BA box no.3 b) Pneumatic panel
c) Behind BA box no.1 d) Behind BA box no.4
Answer (B)
1206) Location of C2B relay valve in WAG-5, WAM4 & WAG7 (up to 27199) is at…………
a) In between MR-1 & MR-2 b) In between MR-3 & MR-4
c) In between MR-2 & MR-3 d) Pneumatic panel
Answer (B)
1207) Location of C2B relay valve in WAG-7 (27200 onwards) & WAP4 crew friendly cab locos is
at………….
a) In between MR-1 & MR-2 b) In between MR-3 & MR-4
c) In between MR-2 & MR-3 d) Pneumatic panel
Answer (D)
1208) Location of EP-3 coc in WAG-7(27200 onwards) & WAP-4 locos is...
a) Near BA-4 panel b) Near BA-3 panel c) Near BA-2 panel d) Near BA-1 panel
Answer(A)
Tower Car
1209) Which of the following is 4 wheeler Tower car?
a) Mark-II b) Mark-III c) Mark-IV d) All of the above
Answer(d)
Answer(d)
1213) Which Tower car has Twin pipe air brake system?
a) Mark-II b) Mark-III c) DHTC d) DETC
Answer(d)
1215) Which Tower car has Gear box system for power Transmission?
a) Mark-II b) Mark-III c) DHTC d) DETC
Answer(a)
1217) Which Tower car has one powered and one non powered axel?
a) Mark-III b) Mark-IV c) DHTC d) both a&b
Answer(d)
1218) Which Tower car has Two powered and Two non powered axels?
a) Mark-III b) Mark-IV c) DHTC d) both a&b
Answer(c)
1221) How much is the axel load of Mark III Tower car?
A) 11 Tones B) 16 Tones C) 15 Tones D) 18 Tones
Answer(B)
1235) What is the rating of Battery in DHTC Tower Wagon for starting in AH?
A) 280 AH B) 290 AH C) 270 AH D) 300 AH
Answer(B)
1251) How many number of axels are there in Mark II tower car?
A) 2 B) 3 C) 5 D) 4
Answer(A)
1252) How many number of axels are there in Mark III tower car?
A) 4 B) 2 C) 3 D) 5
Answer(B)
1253) How many number of axels are there in Mark IV tower car?
A) 4 B) 6 C) 3 D) 2
Answer(D)
1254) How many number of axels are there in DHTC tower car?
A) 7 B) 6 C) 4 D) 5
Answer(C)
1255) How many number of axels are there in DETC tower car?
A) 4 B) 5 C) 6 D) 7
Answer(A)
1257) How many Traction motors mounted on Driving Power Car in DETC Tower Wagon?
A) 4 B) 6 C) 8 D) 7
Answer(A)
1258) What is the name of Oil used for Final Drive in DHTC Tower Wagon?
A) Gear oil EP 09 or HP 90 B) Diesel C) Lubricant oil D) Servo 68
Answer(A)
1259) What must be the minimum pressure of lube oil of Tower Wagon?
A) 3 KG/cm² B) 8 KG/cm² C) 5 KG/cm² D) 7 KG/cm²
Answer(C)
1262) Which type of Tower Wagon has cooling system with Roof Mounted radiator with Hydrostatic fan
drives?
A) DETC B) 8 wheeler DHTC C) Mark-II D) Mark-III
Answer(B)
1263) How many brake cylinders are there in MARK-III Tower Wagon?
A) 5 B) 4 C) 6 D) 7
Answer(C)
1264) What is the maximum allowable water temperature allowed in Tower Wagon?
A) 85°C B) 95°C C) 75°C D) 100°C
Answer(B)
1265) What is the Relay provided to detect Ground Faults in Power Circuit?
A) Relay Section B) Ground Fault Relay (GR) C) RCFR D) Safety Relay
Answer(B)
1266) What is the fuel tank capacity of Mark II Tower car in litres?
A) 200 B) 300 C) 800 D) 600
Answer(A)
1267) What is the fuel tank capacity of Mark III Tower car?
A) 700 Ltrs B) 300 Ltrs C) 400 Ltrs D) 650 Ltrs
Answer(B)
WAG7
1270) Continuous tractive effort at wheel rim of WAG7 loco is
Answer(b)
Answer(c)
Answer(a)
1273) EFDJ coil of DJ in WAG7 loco is
Answer(b)
Answer(c)
a) 25 KV AC b) 1500 V DC c) 11 KV AC d) 440 V AC
Answer(a)
Answer(d)
Answer(b)
DEMU
1400HP BIT BANK
S.NO QUESTION ANSWER
1278) DEMU stands for A
A) diesel electric multiple unit B) Diesel Electronic Multiple Unit
C)Diesel Electric Multipurpose Unit D) Direct Electric Multiple Unit
1279) Power transmission in 1400Hp C
A)DC-DC B) AC-AC C) AC-DC D) DC-AC
1280) DCS stands for A
A) Driver Control Switch B) Driving Circuit Switch
C) Dead man Control Switch D) Dead man Circuit Switch
1281) GCS stands for B
A)Guard Circuit Switch B) Guard Control Switch
C) Ground Control Switch D) Ground Circuit Switch
1282) BIV stands for D
A)Breaker Isolating Value B)Branch Isolating Value
C)Break Ignition Valve D)Break Isolating Valve
1283) MCOS stands for B
A)Motor Control Switch B) Motor Cut Out Switch
C) Multiple Control Switch D) Multiple Cutout Switch
1284) GRCOS stands for D
A)Guard Control Switch B) Guard Relay Cutout Switch
C)Ground Relay Control Switch D) Ground Relay Cutout Switch
1285) EPG stands for C
A) Electro Pneumatic Gauge B)Electric Pressure Gauge
C) Electro Pneumatic Governor D)Electro Pressure Governor
1286) OPS stands for A
A)Oil Pressure Switch B) Over Speed Switch
C)Oil Pressure Scale D) Over Pressure Pneumatic Switch
1287) LWS stands for A
A)Low Water Switch B) Low Water Scale
C) Lead Working Switch D) Load Working Switch
1288) MPU stands for C
A)Multiple Unit B) Multipurpose Unit
C)Magnetic Pickup Unit D) Magnetic Pressure Switch
1289) TA stands for B
A)Tractive Alternator B)Traction Alternator
C)Tractive Effort. D) None Of The Above
1290) TM stands for B
A)Tractive Motor B) Traction Motor
C)Tractive Meter. D)None Of The Above
1291) ECP stands for C
A)Electronic Control Panel B) Electric Control Panel
C) Engine Control Panel D)Electric Contactor Panel
1292) ECP is located in B
A)Driver Cabin B) Engine Room C)Radiator Room D)Control Panel
1293) EFR stands for A
A)Exciter Field Resistor B) Excitation Field Relay
C) Exciter Field Relay D)Engine Forward Relay
1294) EFR is located in B
A)Driver Cabin B) Engine Room C) Radiator Room D)Control Panel
1295) EFR is connected in _______to alternator field supply A
A)Series B) Parallel C)Series Parallel D) Parallel Series
1296) 24V Battery knife switch is located in B
A)Driver Cabin B) Engine Room C)Radiator Room D) Control Panel
1297) _____No of starter motors available on the engine B
A)One B)Two C)Three D)Four
1298) Starter motors are located on the Engine ______ side A
A)Right B)Left C)Top D)Bottom
1299) No of batteries used for Engine cranking D
A)4 Batt Each 6V B) 2 Batt Each 12V C)1 Batt Each 24V D)3 Batt Each 8V
1300) After cranking _______gives supply for charging A
A)24V Alter B) 110v Alter C) Main Alter D) Aux Alter
1301) 24 V Alternate is ______ Driven A
A)Belt B) Gear C)Self Driven D)None Of The Above
1302) 24v battery discharge light is available on ________ C
A)Engine Control Panel B) Control Panel
C) Instrumental Panel D) Driver Desk
1303) OPS is located on Engine _____ side B
A)Right B) Left C)Top D)Bottom
1304) Water Temperature switches is located on ______sides of the engine C
A)Right B) Left C) Both Left And Right D) None Of The Above
1305) Safety device provided in the lube oil system is ______ B
A)OPS B)LWS C)Temperature Switch D)None Of The Above
1306) When coolant water reduces ____safety switch is operated A
A)LWS B)OPS C) HOL D)Water Temp Switch
1307) Actuator is located on _____side of the Engine B
A)Right B)Left C) Top D) Bottom
1308) FSD valve is located on _______ side of the Engine B
A)Right B)Left C)Top D)Bottom
1309) No of MPU available in 1400Hp DPC _______ B
A)One B)Two C)Three D)Four
1310) 24V Battery Ammeter is available on _________ C
A)Engine Control Panel B) Control Panel
C) Instrumental Panel D) Driver Desk
1311) BP Pressure switch is available ___________ A
A)In Control Desk B) In Control Panel
C)Under Slung D)Engine Room
1312) Parking Brake pressure switch is located ______________ A
A)In Control Desk B) In Control Panel
C)Under Slung D)Engine Room
1313) Parking brake magnet valves are located __________ A
A)In Control Desk B) In Control Panel
C)Under Slung D)Engine Room
1314) 110V Alternator is _______ Driven B
A)Gear B) Belt C)Self Driven D)None Of The Above
1315) No of belts provided to drive 110V alternator______ D
A)Three B)Four C)Five D)Six
1316) Auxiliary generator AC output is converted and Regulated by _________ C
A)Rectifier B)DC-DC Convertor C)RRU D)None Of The Above
1317) Auxiliary generated rated kilowatt in 1400hp DPC ________ D
A)12 B)14 C)12.5 D)18.5
1318) RRU stands for ________________ B
A)Rectifier Cum Regulating Unit B) Radiator Regulating Unit
C)Regulator Unit D) None Of The Above
1319) The regulated output of RRU over the entire speed range of RPM is C
__________
A)125/110V DC B)130/110VDC C)135/110VDC D)135/115VDC
1320) DC-DC converter is located in _______________ B
A)Engine Control Panel B) Control Panel
C) Instrumental Panel D) Driver Desk
1321) Flasher control unit is located in _______________ B
A)Engine Control Panel B) Control Panel
C) Instrumental Panel D) Driver Desk
1322) No of Traction Motors available in single DPC ___________ C
A)Two B)Three C) Four D) Six
1323) Type of Traction motor used in 1400 hp DEMU are _____________ A
A)DC Series Wound B) DC Shunt Motor C)DC Compound D) Separately
Excited
1324) No of Poles in Traction motor _______ D
A)One B)Two C)Three D)Four
1325) Cooling type used in DEMU Traction Motors _____________ A
A)Self Ventilated B)Separately Ventilated C)Both A & B D)None
1326) No of inspection covers available for each traction motor __________ C
A)One B)Two C)Three D)Four
1327) No of Brush arms available in each traction motor ________ D
A)One B)Two C)Three D)Four
1328) No of Brush holders available pet arm in 1400hp traction motor _______ B
A)One B)Two C)Three D)Four
1329) No of brushes available in each traction motor of 1400hp DEMU _______ C
A)Four B)Eight C)Twelve D)Sixteen
1330) Brush grade used in BHEL Traction motor ________ A
A) EG14D B)E0. C)EG52. D)None
1331) Condemn size TM brush is _______ B
A)20mm B)25mm C)15mm D)10mm
1332) Type of grease used for lubricating pinion end and commutator end is C
A)Servo RR1 B)Servo RR2 C)Servo RR3 D) ServoRR4
1333) Quantity of grease for first fill at pinion end is ________ D
A)227gms B)350gms C)420gms D)565gms
1334) Quantity of grease for first fill at commutator end is __________ A
A)227gms B)350gms C)420gms D)565gms
1335) No of teeth available on pinion of 1400hp DEMU traction motor ______ C
A)16 B)18 C)20 D)22
1336) Traction motor sequence in 1400hp DEMU ________ B
A)1,2,3,4 B)1,3,2,4 C)1,4,2,3 D)1,2,4,3
1337) No of power contactors available in 1400hp DPC ______ D
A)One B)Two C)Three D)Four
1338) For converting AC to DC _______ is provided. A
A)Rectifier B)Regulator C)Inverter D)Convertor
1339) All Traction motors are connected in ________to the rectifier. B
A)Series B)Parallel C)Series Parallel D)Parallel Shunt
1340) Safety device provided for protecting traction motor from over current D
________
A)GR B)SR C)WSR D)MOLR
1341) MOLR stands for ____________ C
A)Multiple Operating Relay B)Multiple Over Loading Relay
C)Motor Overload Relay D)None Of The Above
1342) MOLR Operates whenever traction motor current crosses more than B
_______Amps
A)600amps B)700amps C)800amps D)800amps
1343) MOLR is connected in _________ with each motor to detect overload. B
A)Parallel B)Series C)Series Parallel D)None
1344) To identify earth fault in power circuit _______ is provided. A
A)GRCO1 B)GRCO2 C)Both A & B D) None
1345) Ground relay is connected in _________side of the power circuit B
A)Positive B)Negative C)Both Side D)None
1346) To identify the earth fault in control circuit _________ is provided B
A)GRCO1 B)GRCO2 C)Both A & B D) None
1347) To reset MOLR _________switch is to be kept off. C
A)Excitation B) EP C)Control D)Test Sequence
1348) No of inter vehicle couplers provided in 1400hp DPC _______ C
A)Three B)Four C)Five D)Six
1349) Each coupler has ______number of wires D
A)16 B)21 C)20 D)19
1350) Excitation and engine speed is controlled by ______ A
A)LCC B)ECP C)Rectifier D)RRU
1351) Engine speed feed back is taken from ________ B
A)Taco Generator B)MPU C)Both A & B D) None
1352) Voltage feed back is given to LCC from ___________ in 1400hp DPC B
A)Current Transformer B)Potential Transformer
C) Tangi D)Bangi
1353) Potential transformer is located in _____________ C
A)Alternator B)RRU C)Rectifier D)Control Panel
1354) Current feed back is given to LCC from _____________ A
A)Current Transformer B)Potential Transformer
C) Tangi D)Bangi
1355) Current transformer is located in __________ C
A)Alternator B)RRU C)Rectifier D)Control Panel
1356) Idle RPM of 1400hp DEMU engine is ______ A
A)700 B)750 C)1000 D)1100
1357) Maximum engine RPM of 1400hp DEMU is ________ D
A)1000 B)1200 C)1600 D)1800
1358) After isolating Traction motor DPC responds up to ________ B
A)2ND Notch B)4TH Notch C)6TH Notch D)8TH Notch
1359) No of positions in ECS _______ B
A)One B)Two C)Three D)Four
1360) MOLR reset switch is __________switch. D
A)Toggle B)Separately Operated C)Automatically Operated
D)Spring Loaded
1361) LAS stand for __________. B
A)Load Ammeter Switch B) Load Ammeter Selector
C)Load Ampere Switch D)Load Ampere Selector
1362) LAS is located on ___________ C
A)Rectifier B)Control Panel C)Control Desk D)Engine Room
1363) Parking brake push buttons are located on __________ A
A)Control Desk B)Control Panel C)Under Slung D)Engine Room
1364) Control switch provided in _____ C
A)Control Panel B)ECP C)DCS D)Instrumental Panel
1365) EP switch is provided in ______ C
A)Control Panel B)ECP C)DCS D)Instrumental Panel
1366) To isolate EP brake _______ to be kept off B
A)Control Switch B)EP Switch C) Excitation Switch D)MOLR Switch
1367) DCS is provided on ___________ A
A)Control Desk B)Control Panel C)Under Slung D)Engine Room
1368) Dead Man Brake is provided in __________ A
A)Master Controller B) DCS C)Indication Panel D)Control Panel
1369) No of Notches available in throttle handle ________ C
A)4 B)6 C)8 D)10
1370) 24v Batteries are provided on _______ side of the DPC A
A)Right B)Left C)Top D)Front
1371) 110V Batteries are provided on ______ side of the DPC. B
A)Right B)Left C)Top D)Front
1372) RRU is located on the ______side of the DPC A
A)Right B)Left C)Top D)Front
1373) Start button is provided on ______ B
A)DCS B)ECP C)Instrumental Panel D)Control Panel
1374) Stop button is provided on _____ B
A)DCS B)ECP C)Instrumental Panel D)Control Panel
1375) Engine related faults are shown on _____ B
A)Indication Panel B)ECP C)Instrumental Panel D)Control
Panel
1376) Whenever grounding occurs in power circuit _________indication glows. C
A)Control Ground B)ALT Failure C)Power Ground D)TM Overload
1377) Whenever RRU fails to give output _________ indication glows. B
A)CONTROL GROUND B)Aux Alt Failure C)Power Ground
D)None
1378) Whenever MOLR trips ________indication glows in indication panel. D
A)Control Ground B)Alt Failure C)Power Ground D)Tm Overload
1379) Indication panel is located on ________ A
A)Control Desk B)Control Panel C)Under Slung D)Engine Room
1600HP DEMU BIT BANK
1380) The power transmission in 1600hp DEMU is _________ B
A)DC-DC B) AC-DC-AC C) AC-DC D) DC-AC-DC
1381) Type of Traction motor used in 1600hp DEMU is ______________ C
A)DC Series Wound B)DC Compound
C)3phase Ac Induction D)AC Synchronous
1382) The component used for converting DC to AC in 1600hp DEMU is ________ A
A)IGBT B)Diode C)Resistor D)Thyrister
1383) IGBT stands for __________________ A
A)Insulated Gate Bipolar Transistor B)Isolated Gate Bipolar Thyrister
C)Insulated Gate Bipolar Thyrister D)Isolated Gate Bipolar Thyrister
1384) DPC is controlled by _____________ D
A)ECU B)ECM C)TCC D)VCC
1385) VCC stands for B
A)Vehicle Control Convertor B)Vehicle Control Computer
C)Ventilator Control Computer D) Vehicle Control Cubicle
1386) VCC is located in D
A)Driver Desk B)TCC C)APC D)Control Panel
1387) ADB stands for B
A)Analogue Digital Box B)Analogue Distribution Box
C)AC DC Box D)None
1388) ADB is provided in ________________ D
A)Driver Desk B)TCC C)APC D)Control Panel
1389) Start Button is provided on ___________in 1600hp DPC D
A)Driver Desk B)TCC C)APC D)Control Panel
1390) Stop Button is provided on __________ in 1600hp DPC D
A)Driver Desk B)TCC C)APC D)Control Panel
1391) Isolation switch has ________position C
A)One B)Two C)Three D)Four
1392) Compressor is driven by _________ C
A)Gear B)Belt C)Motor D)None
1393) APC stands for A
A) Auxiliary Power Convertor b) Auxiliary Power Contactor
C) Air Pressure Controller d) Analogue Power Converter
1394) 110V Battery is charged by _______output in 1600hp DPC B
A)Aux Alternator B)APC C)24v Alternator D)TCC
1395) Compressor motor gets supply from ___________ A
A)APC B)TCC1 C)TCC2 D)VCC
1396) TCC stands for _____________ C
A) Traction Convertor Cubicle b) Tractive Control Computer
C) Traction Control Convertor d) None
1397) TCC1 gives supply to the ________motors B
A)1 & 3 B)1 & 2 C)3 & 4 D)2 & 4
1398) TCC2 gives supply to the ________motors C
A)1 & 3 B)1 & 2 C)3 & 4 D)2 & 4
1399) DC link junction box is provided in _________ room C
A)Driver Desk B)Control Panel C)Engine Room D)Radiator
1400) TCC2 is located on _________ side of the DPC A
A)Right B)Left C)Top D)Bottom
1401) ECU is provided in ____________ B
A)Driver Desk B)Control Panel C)Engine Room D)Radiator
1402) ECU is located on __________ C
A)Driver Desk B)Control Panel C)Engine D)Radiator
1403) Rectifier is mounted on ____________ A
A)Alternator B)Engine C)Under Slung D)None Of The Above
1404) Rectifier is located in __________ C
A)Driver Desk B)Control Panel C)Engine Room D)Radiator
1405) No of electrical driven blowers available in 1600hp DPC _________ B
A)One B)Two C)Three D)Four
1406) Electrical driven blowers are provided in _________ C
A)Driver Desk B)Control Panel C)Engine Room D)Radiator
1407) Engine is controlled by _________ D
A)ECU B)APC C)TCC1&TCC2 D)ECM
1408) Hydraulic fan speed is controlled by ___________ D
A)ECU B)VCC C)APC D)HCU
1409) HCU is located in __________ B
A)Driver Desk B)Control Panel C)Engine Room D)Radiator
1410) ACOR is provided in ___________ A
A)Driver Desk B)Control Panel C)Engine Room D)Radiator
1411) TCC2 is located on _________ side of the DPC A
A)Right B)Left C)Top D)Bottom
1412) Starter motors are provided on ________ side of the Engine in 1600hp DPC B
A)Right B)Left C)Top D)Bottom
1413) No of starter motors available in 1600HP DPC _______ B
A)One B)Two C)Three D)Four
1414) Pre lube motor is located on ________side of the engine. B
A)Right B)Left C)Top D)Bottom
1415) Hydraulic filter clog sensor is located in ________ room D
A)Driver Desk B)Control Panel C)Engine Room D)Radiator
1416) APC is located on________ side of the DPC. B
A)Right B)Left C)Top D)Bottom
1417) TCC1 is located on ______ side of the DPC B
A)Right B)Left C)Top D)Bottom
1418) TCC2 is located on _______ side of the DPC A
A)Right B)Left C)Top D)Bottom
140T CRANE BIT BANK
1419) How many batteries available in 140T crane – _________ B
A)ONE B)TWO C)THREE D)FOUR
1420) 140T crane battery ampere hour capacity __________ A
A)180AH B)120AH C)450AH D)500AH
1421) Operating (control) Voltage of 140T crane____________ C
A)230V AC B)110V DC C)24V DC D)110V AC
1422) How many electrical rotating equipment’s in 140T crane for main engine B
________
A)ONE B)TWO C)THREE D)FOUR
1423) How many electrical rotating in 140T crane for aux engine ________ B
A)ONE B)TWO C)THREE D)FOUR
1424) How many self starter motors available in 140T crane _______ A
A)ONE B)TWO C)THREE D)FOUR
1425) 24V alternator rotates with No of belts ________ B
A)ONE B)TWO C)THREE D)FOUR
1426) Purpose of self starter motor- ___________ A
A)START THE ENGINE B)STOP THE ENGINE C)BOTH A & B
D)NONE
1427) Purpose of 24v alternator To Charge The _________ A
A)24V BATTERIES B)110VBATTERIES C) BOTH A & B D)NONE
1428) No of Traction motors available in 140T crane-_______ D
A)TWO B)THREE C)FOUR D)NIL
DHMU(ART & MRV ) BIT BANK
1429) DHMU means ______________ C
A)Direct Hydraulic Multiple Unit B)Diesel Hydraulic Multi Purpose Unit
C)Diesel Hydraulic Multiple Unit D)Diesel Hydro Multiple Unit
1430) SPMRV means _______________________- B
A)Self Propelled Medicine Relief Van B)Self Propelled Medical Relief Van
C)Self Propelled Motor Relief Van D)Self Propelled Medical Run Van
1431) How many transmissions available in one DPC ________ B
A)One B)Two C)Three D)Four
1432) Max speed of MRV _________ D
A)90 B)100 C)105 D)110
1433) Max speed of ART __________ D
A)90 B)100 C)105 D)110
1434) How many traction motors available in MRV & ART _________ D
A)One B)Two C)Three D)Nil
1435) TC means ___________ A
A)Trailer Car B)Training Car C)Training Coach D)None
1436) Horse power of ART and MRV _______ C
A)1400hp B) 1600hp C)700hp D)2400hp
1437) Engine cranking voltage of MRV and ART B
A)110V DC B) 24V DC C) 72V DC D) 12V DC
1438) Engine cranking batteries ampere hour capacity in MRV and ART B
A)72AH B) 450AH C) 120AH D) 900AH
1439) No of batteries available for engine cranking for MRV & ART D
A)2 No’s each 12V B) 4No’s each 6V C)1no’s 24v D) 3No’s each 8V
1440) MRV & ART formation control voltage for operation _________ A
A)110V DC B) 24V DC C) 230V AC D) 440V AC
1441) MRT & ART control voltage battery ampere hour capacity __________ C
A)72AH B) 450AH C)120AH D) 900AH
1442) No of batteries available for control voltage ________ A
A)18No’s B) 03No’s C) 13No’s D) 08No,s
1443) How many alternators available for 24V battery charging __________ B
A)01No’s B) 02No’s C) 03No’s D) 04No’s
1444) How many alternators available for 110V battery charging __________ B
A)01No’s B) 02No’s C) 03No’s D) 04No’s
1445) Which type of transmission available in MRV & ART __________ C
A)AC-DC B) DC-AC C) Hydraulic D) DC-DC
1446) How many transmissions available in MRV & ART __________ B
A)01No’s B) 02No’s C) 03No’s D) 04No’s
1447) In forward direction one transmission engaged forward direction another B
transmission should engage ________direction
A)Forward B) reverse C)forward and reverse D) None of the
above
1448) How many notches available in master controller ___________ C
A)4 Notches B) 6 Notches C) 8 Notches D) 10 Notches
1449) What is engine speed difference in 7th and 8th notches in MRV & ART B
A)400RPM B) 0RPM C) 200RPM D) 100RPM
1450) Air pressure required for engaging transmission __________ A
A)5Kg/cm2 B) 2Kg/cm2 C) 3Kg/cm2 D) 9Kg/cm2
1451) How many fuel solenoid valves available in MUSD C
A)02No’s B) 03No’s C) 04No’s D) 06No’s
1452) If high transmission oil temperature relay operated engine comes to B
A)Shutdown B) Idle C) reduction in RPM D) none of the above
1453) If high transmission oil temperature relay operated engine comes to ______ A
A)Shutdown B) Idle C) Reduction in RPM D) None of the
above
1454) In MRV & ART safety relay for low hydraulic oil level __________ A
A)R21 or R22 B) R61 or R62 C)R11 or R12 D) R31 or R32
1455) In MRV & ART safety relay for low cooling water level _________ B
A)R21 or R22 B) R61 or R62 C)R11 or R12 D) R31 or R32
1456) In MRV & ART safety relay for over speed trip _________ D
A)R21 or R22 B) R61 or R62 C)R11 or R12 D) R51 or R52
1457) In MRV & ART safety relay for low lube oil pressure ___________ C
A)R21 or R22 B) R61 or R62 C) R41 or R42D) R51 or R52
1458) In MRV & ART safety relay for high cooling water temperature C
A)R21 or R22 B) R61 or R62 C)R11 or R12 D) R31 or R32
1459) In MRV & ART safety relay for High transmission oil temperature _________ D
A)R21 or R22 B) R61 or R62 C)R11 or R12 D) R31 or R32
1460) In MRV & ART Sov for stand still detection ________ A
A)SOV81 & SOV 82 B)SOV 71 & SOV 72 C)SOV91 & SOV92 D) None
1461) In MRV & ART convertor control solenoid valve connected with PP1 is C
__________
A)SOV 51 B) SOV 52 C)SOV71 D)SOV72
1462) In MRV & ART convertor control solenoid valve connected with PP2 is D
______
A)SOV 51 B) SOV 52 C)SOV71 D)SOV72
1463) In MRV &ART transmission forward solenoid valve of PP1 is _______ B
A)SOV 51 B) SOV 91 C)SOV71 D)SOV72
1464) In MRV & ART engine fuel solenoid valve of PP1 _________ A
A)SOV 51 B) SOV 52 C)SOV71 D)SOV72
1465) In MRV & ART engine fuel solenoid valve of PP2 _________ B
A)SOV 51 B) SOV 52 C)SOV71 D)SOV72
1466) Operating voltage of head light ___________ C
A)110V B)72V C)24V D) 12V
1467) Head light unit gets supply from ________ C
A)110V Batt B)24V Batt C)DC-DC Convertor D)Aux Gen
1468) DC-DC Convertor converts______________ in ART & MRV A
A)110V To 24V B)72V To 24V C)110V To 12V D)72V To 12V
DEMU ELECTRICAL
1469) When OPS drops will cause?
(A) Engine to Idle
(B) Engine shut down
(C) Hot Engine
(D) Lower water alarm
Ans: (B)
1470)What is the OSTA tripping R.P.M. in DEMU?
(A) 1900
(B) 2300
(C) 2200
(D) 2100
Ans: (D)
1471)How many traction motor in DEMU?
(A) 6
(B) 4
(C) 2
(D) 8
Ans: (B)
1472)If any traction motor isolated in DEMU. What is engine R.P.M.?
(A) 750
(B) 1200
(C) 1000
(D) 1300
Ans: (D)
1473)How many engine speed sensors available in 1400 HP DEMU?
(A) 2
(B) 1
(C) 3
(D) 4
Ans: (A)
1474)1400 HP DEMU engine R.P.M. at idle?
(A) 400
(B) 500
(C) 600
(D) 700
Ans: (D)
1475)1400 HP DEMU engine R.P.M. at 8th notch?
(A) 1000
(B) 1100
(C) 1500
(D) 1800
Ans: (D)
1476)No of power contraction in 1400 HP DEMU?
(A) 2
(B) 6
(C) 4
(D) 8
Ans: (C)
1477)What the ‘DEAD MAN’ handle oprate in running?
(A) Engine shot down
(B) Engine come to idle
(C) OSTA tripped
(D) Engine R.P.M. raised
Ans: (B)
1478)How many carbon grosses in 1400HP traction alternator ?
(A) 2
(B) 4
(C) 6
(D) Nil
Ans: (A)
1479)In DEMU engine starting and engine safety circuit voltage ?
(A) 110 V
(B) 24 V
(C) 72 V
(D) 12 V
Ans: (B)
1480)In DEMU control, fan and light supply voltage?
(A) 110 V
(B) 24 V
(C) 72 V
(D) 12 V
Ans: (A)
1481)DEMU head light DC-DC converter input voltage?
(A) 12 V
(B) 72 V
(C) 24 V
(D) 110 V
ANS: (D)
1482)No of reverser in 1400 CGC DEMU?
(A) 4
(B) 3
(C) 2
(D) 1
Ans: (D)
1483)No of reverser in 1400 HP BHEL DEMU?
(A) 1
(B) 2
(C) 3
(D) 4
Ans: (B)
1484)How many jumper cables are available in 1400 HP DEMU?
(A) 4
(B) 2
(C) 3
(D) 5
Ans: (D)
1485)24 V alternator drives by no of belts?
(A) 1
(B) 2
(C) 3
(D) 4
Ans: (A)
1486)24 V alternator make in 1400 HP DEMU?
(A) TBS local
(B) C.G.C.
(C) BHEL
(D) KEL
Ans: (A)
1487)110 V AC alternator make in 1400 HP DEMU?
(A) TBS local
(B) C.G.C.
(C) BHEL
(D) KEL
Ans: (D)
1488)1600 HP DEMU engine idle,R.P.M.?
(A) 700
(B) 750
(C) 400
(D) 600
Ans: (B)
1489)1400 HP DEMU when low cooling water level (LCWL) sensor operated?
(A) Engine to idle
(B) Engine shutdown
(C) Hot engine
(D) Engine to 8th notch
Ans: (B)
1490)When the parking brake applied the parking brake gauge shows?
(A) 5Kg/cm2
(B) 7Kg/cm2
(C) 0Kg/cm2
(D) 3.5Kg/cm2
Ans : (C)
1491)1400 HP DEMU when the T.M. ********** load I.D. coming the load motor shows?
(A) Max.
(B) Min.
(C) Zero
(D) No of the above
Ans: (C)
1492)1400 HP DEMU in E.P.brake system application magnetic valve is?
(A) N.O.(Normally open)
(B) N.C.(Normally close)
(C) N.O.& N.C
(D) None of the above
Ans: (B)
1493)1400HP DEMU in E.P brake system holding magnetic valce is?
(A) Normally Open
(B) Normally Close
(C) Normally Open & Normally Close
(D) None of the above
Ans: (A)
1494)1400HP DEMU formation having no. of coaches?
(A) 2 DPC+6TC
(B) 2DPC+10TC
(C) 2 DPC+4TC
(D) 1 DPC+6TC
Ans: (A)
1495)1600 HP DEMU formation having no. of coaches?
(A) 2 DPC+6TC
(B) 2 DPC+10TC
(C) 2 DPC+8TC
(D) 2 DPC+4TC
Ans: (C)
1496)1400 HP DEMU 4th Notch RPM?
(A) 1000
(B) 1200
(C) 1300
(D) 1400
Ans: (C)
1497)Hot Engine Alarm experienced in 1400 HP DEMU water temperature is?
(A) 85˚C
(B) 93˚C
(C) 78˚C
(D) 68˚C
Ans: (B)