Professional Documents
Culture Documents
WH SDC16H6E5 - + - WH UD16HE5 Hu
WH SDC16H6E5 - + - WH UD16HE5 Hu
WH SDC16H6E5 - + - WH UD16HE5 Hu
H22
PAW-A2W-TSOD [E36]
WH-SDC16H6E5
T
H2
CZ-NS4P
H12 [E39]
[E62] H21
WH-UD16HE5
H1
H104
H24
H6
H5
COMBO TANK PAW-TD20B8E3-1
HxWxD (mm) 1770x640x690
kg 150
H3
Hydraulic Connection
Type BSPP (male)
Inlet & Outlet Size (mm(in)) 32 (1-1/4)
Nom. Flow Rate (l/m) 45.9
E38
(OLP booster)
E37
PAW-A2W-TSRT
(room temp zone 1)
E36
PAW-A2W-TSOD
(outdoor air sensor) 12
E63
E35
E35 11
PAW-TS1/PAW-TS2
(tank sensor) 10
9
E34 E30
ON/OFF 8
(external control)
7
E33 6
RC
(Remote controller) E31
5
M
2
E28
1
E28 E29
AC 230 V AC 230 V
(3 way valve) (Room thermo 1)
C O N H C N L
M
E60
E61 E62
E63
L N L1 N1
1 2 3
connection type
required
optional
POWER SUPPLY 1 POWER SUPPLY 2
Footnotes
Electrical connections: to be defined when the hydraulic scheme and the system Remote Controller: the H generation heat pump remote controller can be used as
H7 E33
control logic have been selected. a room thermostat for only one circuit. The cables maximum length is 50 meters.
Optional thermostat: every circuit can be controlled with one optional thermostat, E35 DHW tank sensor
H9
with one room sensor or with the remote controller (only for 1 circuit).
Buffer tank / Volumiser: in the open primary circuit (when all heating - cooling E36 Outdoor air sensor (optional)
circuits are closed) it is recommended a minimum water volume of at least 30
H10 E37 Zone 1 room sensor (see point E29)
litres up to and including 9 kW units and 50 litres for 12 & 16kW (kW stated is
nominal heating capacity of the heat pump A7/W35).
OLP booster heater: on the OLP contact must be put a jumper if external booster
E38
Heating/cooling circuit: If the HP is connected directly to the system, the minium heater is used and controlled by Panasonic heat pumps.
water flow rate must be guaranteed. Provide an overflow valve (recommended 1''
Optional PCB: the maximum cable length for sensor inputs is 30 meters and the
diameter) or a 3-way diverting valve on hydronic indoor units (fan-coil, duct unit
H11 maximum cable length for outputs and other inputs is 50 meters.
etc.) or a thermostat must be removed to ensure sufficient flow. If you have floor E39
heating provide a safety thermostat (for heating mode) and a dew-point sensor
(for cooling mode).
E40 Zone 2 room sensor (see point E29)
H12 Optional PCB - CZ-NS4P - needed for this scheme
E41 Zone 1 room sensor (see point E29)
H13 Mix valve with 3 points control
Secondary water pump: they must be chosen according to the system hydraulic E42 Buffer tank sensor
H14
performance.
H15 Boiler E43 Pool water sensor
H16 Solar panels E44 Water sensor zone 2 (see point E29)
H17 Solar pump E45 Water sensor zone 1 (see point E29)
PAW-TD20B8E3-1: the Aquarea Tank includes the domestic hot water tank (200 E51 Mixing valve zone 2
litres), the 3 way valve, the buffer tank for heating and cooling system (80 litres),
secondary circulating pump, tank sensor (CZ-TK1) and booster heater inside the E52 Mixing valve zone 1
H24 DHW tank (3 kW). PAW-TD20B8E3-1 does not have a dedicated secondary return
circulation connection, if this is required then the return circulation pipe must be E53 Optional thermostat 1 (see point E29)
connected to the cold water feed inlet pipe.
E54 Optional thermostat 2 (see point E29)
3 way valve: it is possible to install the Panasonic 3 way valve inside the indoor
H25 unit (code CZ-NV1) or ouside the indoor unit (code PAW-3WYVLV-SI). The DHW E55 Pool pump
temperature sensor must be ordered separately (see point H24).
E56 Solar pump
Shut-off valve
Pressure regulator
E60 Indoor unit power supply
Boiler circuit pipes
E61 Indoor unit power supply 1 - main
Solar panels circuit pipes
E62 Indoor unit power supply 2 - heaters
Pipes
Connection to the outdoor unit: the outdoor unit power supply comes from the
Domestic cold water pipe E63 indoor unit, so it is not necessary to bring a direct power supply to the outdoor
unit.
Circulation circuit pipes
Electrical box on the PAW-TD20B8E3-1: connection from the Aquarea Tank
E64
Electrical wired cables electrical box to the Aquarea Heat Pump main board PCB.
Attention: All requirements in this page are only examples and they are not a project design specific. Refer always to the documentation provided by Panasonic.
Panasonic is not responsible, directly or indirectly, towards users and in general towards any third party for any delays, inaccuracies, errors, omissions, damages (direct, indirect,
consequential, and punishable) arising from such contents. Texts, photos, graphics, may not be published, rewritten, marketed and distributed by users and third parties in general,
in any way and in any form if not expressly indicated in written form by Panasonic itself.