Professional Documents
Culture Documents
High-Density Process Monitoring System: Instructions and Operating Manual
High-Density Process Monitoring System: Instructions and Operating Manual
and
Operating Manual
MODEL X87
HIGH-DENSITY PROCESS
MONITORING SYSTEM
—
•-
V
( Kv
s -EEE--========= )
31 RONAN
TABLE OF CONTENTS
1.0 General Description............................. 3
2.0 Specifications...................................... 3
3.0 Installation—General.......................... 4
3.1 Dimensions . .... .................................. 4
3.2 Installation—Rack Mounting .............. 4
3.3 Power Requirements ......................... 4
3.4 Wiring Instructions .. ............................ 4
3.5 Three-Wire RTD Configuration ........... 4
3.6 Two-Wire RTD Configuration.............. 4
3.7 Two-Wire Versus Three-Wire Configuration 4
3.8 Input Wiring Instructions..................... 5
3.9 Thermocouple Connection.................. 5
3.10 Auxiliary Relay Wiring 5
3.11 Auxiliary Relay Contact Current 5
3.12 External Relay Use 5
4.0 System Accuracy Verification and Calibration............................... ........................... 5
4.1 RTD Accuracy Test and Calibration.......................................... ..................... 5
4.2 Thermocouple Accuracy Test and Calibration...........................................................
6
4.3 Transmitter Accuracy Test and Calibration..............................................................
7
4.4 Master Module Accuracy Test and Calibration............................................... .......... 7
5.0 System Operation Verification....................................................................... ............ 8
5.1 Test Verification..............................................................
8
5.2 Silence Verification..............................................................
8
5.3 Reset Verification..............................................................
8
5.4 Auxiliary Relay Operation Verification....................................................... ................ 8
5.5 Setpoint Alarm Verification..............................................................
8
5.6 Input Failure Verification..............................................................
9
5.7 Removal of Input Module from System ...................................................... ............. 9
6.0 Circuit Description............... .. ............................................. ..................................... 10
6.1 Input Module, Models X87-300, -400, -470, -471,-472, -473 (Schematic X87-1000, -1016) 10
6.2 Thermocouple, mV, mA Amplifier, Models X87-S10, -S20 (Schematic X87-1002).. 11
6.3 RTD Amplifier, Model X87-S00 (Schematic X87-1001)............................................
11
6.4 Vibration Input Amplifier, Models X87-S70, -S74, -S76 (Schematic X87-1017)....... 12
6.5 Position Input Amplifier, Model X87-S78 (Schematic X87-1012)............... ............. 12
6.6 Frequency Input Signal Conditioner Model X87-579 (Schematic X87-1018)........... 13
6.7 Transmitter, Model X87-600 (Schematic X87-1004) 13
6.8 Master Module, Model X87-100B (Schematics X87-1003, -1005) 13
6.9 Linearizer, Model X87-200 (Schematic X83-1004)............... 14
6.10 Engineering Units Linearizer, Model X83-200-EU (Schematic X83-1031) 14
6.11 Digital Panel Meter, Model X87-101 (Schematics X83-1005, -1006) 15
7.0 Parts Lists
S87-S00 RTD Amplifier ............................................................ 15
X87-S10, -S20 Thermocouple, Engineering Units Amplifier..... 16
X87-S70, -S73, -S74, -S75, -S76, -S77 Vibration Input Amplifier 17
X87-S78 Position Input Amplifier............................................. 19
1
TABLE OF CONTENTS (continued)
7.0 Parts Lists (Continued)
X87-S79 Frequency Input Board................................................................................................. 20
X87-T00 Setpoint Range Submodule.......................................................................................... 21
X87-100B Master Module .........................................
21
X87-300 Single-Setpoint Input Module .. ......... .......................................................................... 23
X87-400 Dual-Setpoint Input Module..........................................
26
X87-470, -471,-472 Dual-Setpoint Vibration Input Module..........................................
29
X87-478 Dual-Setpoint Position Input Module .........................................
32
X87-600 Transmitter.................................................................................................................... 35
X83-200-100 Linearizer . ............................................................................................................ 36
X83-200-120 Linearizer............................................................................................................... 37
X83-200-E Linearizer................................................................................................................... 39
X83-200-J Linearizer................................................................................................................... 40
X83-200-K Linearizer................................................................................................................... 41
X83-200-T Linearizer................................................................................................................... 42
X87-200-R Linearizer................................................................................................................... 43
X87-200-S Linearizer............................................................................................... .................... 44
X83-200-EU Linearizer................................................................................................................. 45
8.0 Drawings
Schematic, X87-1000 Input Module (Models X87-300, -400, -470, -474, -476, -478)................ 46
Schematic, X87-1001 RTD Amplifier (Model X87-S00).................. 47
Schematic, X87-1002 Thermocouple, mV, mA Amplifier (Models X87-S10, -S20).................... 48
Schematic, X87-1003 Master Module (Horizontal Board) (Model X87-1008)............................. 49
Schematic, X87-1004 Transmitter (Model X87-600)......................... ......................................... 50
Schematic, X87-1005 Master Module (Vertical Board) (Model X87-100B)................................. 51
Schematic, X87-1012 Position Input Amplifier (Model ..... .......................................................... 52
Schematic, X87-1016 Vibration Monitor, Single and Dual Setpoint (Model X87-470, -471,-472, -473) 53
Schematic, X87-1017 Vibration Input Board..................................................... ......................... 54
Schematic, X87-1018 Frequency Input Board............................................................................. 55
Schematic, X83-1004 Linearizer (Model X87-200) ..................................................................... 56
Schematic, X83-1005 Digital Panel Meter (Model X87-101)......................................... .............. 57
Schematic, X83-1006 Digital Panel Meter Display Board (Model ........................................
58
Schematic, X83-1031 Engineering Units Linearizer (Model X83-200-EU).................................
59
Outline Drawing, X87D1 Relay Rack Enclosure..........................................
60
Terminal Arrangements, X87D36 Relay Rack and Panel Mount.........................................
61
Terminal Arrangements, X87D36 Rack Mount, Panel Mount Vibration Inputs........................... 62
Outline Drawing, X87D46 Panel-Mount Enclosure.........................................
63
Outline Drawing, X87D47 Surface-Mount Enclosure.........................................
•64
Terminal Arrangements, X87D82 Surface Mount........................................................................ 65
Terminal Arrangements, X87D82 Surface Mount Vibration Inputs............................................. 66
Warranty
Ronan warrants equipment of its own manufacture to be free from defects in material and workmanship under normal
conditions of use and service, and will repair or replace any component found to be defective, on its return, transportation
charges prepaid, within one year of its original purchase. This warranty carries no liability, either expressed or implied,
beyond our obligation to replace the unit which carries the warranty.
2
Inputs: RTD, thermocouple, vibration, position, current,
1.0 GENERAL DESCRIPTION voltage or potentiometer
The Ronan Model X87 High-Density Process Input Ranges-RTD:
Monitoring System provides continuous monitoring of Degrees Degrees
sensors and engineering unit inputs, as required by RTD Type Fahrenheit Celsius
most industrial processes and machinery. Each 10 ohm copper 0 to + 300 -20 to +150
system features a number of input modules, or points, 100 ohm platinum - 300 to + 1,000 - 185 to +540
which function with a single master module. The 120 ohm nickel - 50 to + 550 - 45 to + 290
master module provides digital readout of each input Input Range—Thermocouple:
and associated setpoints. The input signals are T/C Degrees Degrees
conditioned and scaled in the input modules and Type Fahrenheit Celsius
continuously compared against set values in the set Chromel/constantan, E - 50 to +1,800 -45 to +1,000
point circuits. Iron/constantan, J — 50 to +1,400 - 45 to + 760
The master module contains a 3 %2-digit panel meter Chromel/alumel, K - 50 to + 2,000 -45 to +1,200
(DPM), operating pushbuttons, signal conditioning and Platinum/13%, + 480 to + 2,000 + 250 to +1,700
linearization circuits, system relays and re-flash circuit. rhodium/platinum, R
Platinum/10%, + 300 to + 2,000 + 150 to +1,700
The inputs and setpoints of each monitor module can
rhodium/platinum, S
be read out on the DPM. The common trouble alarm
Copper/constantan, T - 300 to + 700 - 200 to + 370
(CTA) relay indicates when any setpoint in the system
is in an alarm state. The re-flash relay indicates an Input Ranges-Milliamps: Standard ranges are
alarm condition and pulses once for each subsequent 1-5 mA, 4-20 mA and 10-50 mA. Other ranges can be
alarm. The CTA and re-flash relays return to normal provided.
only when all setpoints return to normal and the Input Ranges-Voltage: Standard ranges are 0-5 V,
system is reset. 1-5 V, 0-10 V and 2-10 V. Other ranges can be provided.
The monitor modules contain input signal conditioning Input Range-Ohms: 0-1000 ohms
and scaling, multiturn, infinite-resolution setpoint
Input Range-Displacement: 0-40 mils peak-peak
potentiometers and single- or dual-setpoint control.
Each setpoint has an individual relay output, which (100 or 200 mV/mil)
provides two sets of isolated contact outputs. The Input Range-Velocity: 0-50 in./sec. peak
input status is annunciated on the monitor module’s (100 mV peak/in./sec.)
front panel via an LED for each setpoint and one for Input Range-Acceleration: 0-50 g’s peak
power and sensor integrity. The alarm sequence (100 mV/g from integral charge amplifier)
operates as a first-out type or as a manual-reset
sequence. Input Range-Shaft Position: 0 to ±40 mils
(100 or 200 mV/mil)
The auxiliary relay operation is jumper plug selectable
for normally energized (NE) or normally de-energized Input Impedance: RTD: >100 kohms;
(NDE) operation and to follow the input, i.e., non Thermocouple: >10 Mohms; 4-20 mA: 3.125 ohms;
latching (NL), or to follow the latching alarm sequence 10-50 mA: 1.25 ohms; Voltage: >100 kohms;
(L). The contacts are also jumper plug selectable for Vibration: 10 kohms
normally open (NO) or normally closed (NC) operation. Sensor Failure Response: Red front-panel LED
A two-position switch for each setpoint provides easy activates system horn; selective alarm inhibit on both
selection of high or low setpoints. An optional setpoints
transmitter can be provided with each input.
Common Mode Voltage: ± 300 VDC or peak AC 60 Hz
The monitor modules accept inputs from resistance without damage
temperature detectors, thermocouples, voltage
System Accuracy: Input module, master module,
sources, current sources and vibration sensors. The
curve-fitting and digital meter: ± 2°F or C for 0-1,000°;
vibration input modules accept inputs from eddy probe
±3°F or C over 1,000 o
systems, velocity transducers and accelerometers
with integral charge amplifiers. A position monitor is Ambient Temperature Effect at 75±40°F:
also available, which measures the axial position of a Gain: ±0.02% of reading per °C
machine shaft. The input signal is provided by an eddy Zero: ± 0.05 °C per °C, ±2u RTI
probe system. Meter Resolution: +1 °C or F
Setpoint Range: Same as sensor input ranges as
shown above. (Range may be reduced on special
2.0 SPECIFICATIONS order.)
Setpoint Resolution: +0.1% of setpoint range
Specifications apply at an ambient temperature Hysteresis: Adjustable by graduated control from 1 oF
of 25 ±2 °C unless otherwise stated. Specifications to approximately 50°F
are subject to change without notice.
3
Alarm Setpoints: One or two, each with DPST contact 3.2 Installation-Rack Mounting
(Form-A or -B) The rack-mounting X87 series are best installed
Contact Rating: General purpose: 3 A at 240 VRMS or on standard EIA rails, which come pre-drilled and
28 VDC, resistive Hermetically sealed: 2 A at tapped at the proper spacing. Should mounting
115 VRMS (Form-A and Form-B); 0.2 A at 115 VRMS on a non-standard rail be attempted, refer to
(Form-C); 2 A at 28 VDC, resistive mechanical drawings for dimensions.
Alarm Sequence: First-out or manual reset
3.3 Power Requirements
Remote Select Option: Input and setpoints selected
for display via remote switches (No analog signals are The Ronan X87 system is designed to operate
routed through remote switches.) from a 24 VDC power supply or battery. Refer to
section 2.0 Specifications for fusing and specific
Master Module Readout: 3 %2-digit panel meter power requirements. Connections are to the 24 V
Shutdown Bypass: Key lock switch with LED indicator "+” and rear terminals.
(flashing if bypass is activated)
Alarm Relay Output: Common trouble alarm: Contact 3.4 Wiring Instructions
rating same as alarm setpoints (Contacts transfer Wiring will depend upon the functional require
when any setpoint goes off normal, will reset after all ments of any particular system. For complete
setpoints normal.) wiring information, refer to the terminal
Re-Flash Relay Output: Contact rating same as arrangements drawing (X87D36).
setpoints (Contacts transfer when first setpoint goes CAUTION: Do not apply power before completion
off normal and pulses for each subsequent alarm.) of all wiring. Carefully review and verify the
Horn Relay Output: Contact rating same as alarm correctness of the wiring using an ohmmeter.
setpoints (Contacts transfer when any point goes into Note: If the module is left connected and
alarm, resets when SILENCE switch is pressed.) energized during the repair of an open input,
Transmitter: alarm conditions will be present. Therefore, the
Output: Isolated; 1-5 mA, 4-20 mA, 10-50 mA module should be unplugged from its connector
0-5 VDC, 1-5 VDC, 0-10 VDC, 2-10 VDC or the system’s shutdown BYPASS switch should
Accuracy: ±0.2% of span (not linearized) be set to the BYPASS position for the duration of
the corrective action.
Power Requirements: 24 VDC± 10%
Power Consumption: W W for master module; add 3.5 Three-Wire RTD Configuration
3.5 W for each monitor module and 0.8 W for each All X87 systems are shipped in the three-wire
optional transmitter ! configuration, unless otherwise specified.
Size: See mechanical dimensions Connect the RTD " + ” wire to terminal 1 and
the RTD wire to terminal 2. Connect the
Weight: Master module: 2.6 lbs. (1.2 kg) } RTD COM to terminal 3.
Chassis: 10.0 lbs. (4.6 kg)
Input modules: 0.7 lb. (0.318 kg) Note: No damage will result if this polarity is not
observed. However, the monitor will not respond
I properly.
COMPENSATION 0 5
RESISTOR
Figure 2a
6
T/C ALLOY LEADS
COPPER LEADS
01
PRECISION 0 2
MILLIVOLT
SOURCE + v V
COLD
3
4
JUNCTION 5
0’ REFERENCE JUNCTION COMPENSATION
OR ICE BATH RESISTOR
Figure 2b
adjustment may be required in the master 4.3 Transmitter Accuracy Test and Calibration
module. (All channels will be inaccurate by the The optional transmitter board is tested and
same amount if the master module needs calibrated while in the system and connected to
calibration.) the monitor module. An extender board should
be used with the monitor module to allow access
to the transmitter’s zero and span adjustment
Temp. Thermoelectric Voltage in Millivolts potentiometers. Connect a calibration input to
°C Reference Junction at 0°C the module under test per section 4.1 or 4.2.
E J K T R S Connect a milliammeter to the transmitter output
"+" (screw terminal 8) and (screw terminal
0 0.000 0,000 0,000 0,000 9). With the input set to the SPAN ZERO of the
+ 50 3.047 2.585 2.022 2.035 transmitter (e.g., 0°C for a 0-500 °C transmitter),
+ 100 6.317 5.268 4.095 4.277
6.137 6.702 1.029
the output should be the zero of the output span
+ 150 9.787 8.008
+ 200 13.419 10.777 8.137 9.286 1.440 (4 mA for a 4-20 mA output). If the measured
+ 250 17.178 13.553 10.151 12.011 1.923 1.873 output is inaccurate, adjust the zero poten
+ 300 21.033 16.325 12.207 14.860 2.400 2.323 tiometer (R2) on the plug-in transmitter board.
+ 350 24.961 19.089 14.292 17.816 2.896 2.786 Set the input to the full-scale value of the trans
+ 400 28.943 21.846 16.395 20.869 3.407 3.260 mitter output. If necessary, adjust using the span
+ 450 32.960 24.607 18.513 3.933 3.743 potentiometer (R1) on the plug-in transmitter
+ 500 36.999 27.388 20.640 4.471 4.234 board (schematic X87-1004).
+ 550 41.045 30.210 22.772 5.021 4.732
+ 600 45.085 33.096 24.902 5.582 5.237 4.4 Master Module Accuracy Test and
+ 650 49.109 36.066 27.022 6.155 5.751
+ 700 53.110 39.130 29.128 6.741 6.274 Calibration
+ 800 61.022 33.277 7.949 7.345 The zero of the master module can be checked
+ 900 68.783 37.325 9.203 8.448 when none of the monitor module inputs or set
+ 1000 76.358 41.269 10.503 9.585 points are selected for readout. With the master
+ 1200 13.224 11.947 module’s internal °C/°F switch in the °C posi
+ 1400 16.035 14.368
18.842 16.771
tion, the DPM should display 0°C. If necessary,
+ 1600
+ 1700 20.215 17.942 the zero control (R41) on the master module’s
horizontal board can be used to adjust the zero.
Table 2: T/C Voltages vs. Temperature To check the gain of the master module, a
Reference: NBS Monograph 125 calibration signal must be applied to the analog
“+” and inputs to the master module. A
4.99 k, 1% resistor must be used in series with
the "+" input to simulate the resistance in
series with the signals from the monitor
modules. Failure to use this series resistor will
7
already on, pressing TEST will activate it. The re
4.99 K, 1 % flash and CTA relays will be energized, if no
points were in alarm when TEST was pressed.
+ ------W---- The TEST pushbutton is enabled only when the
VOLTAGE J1 OR J2, PIN 5 BYPASS switch is in the BYPASS position. This is
CALIBRATOR (AT BACK OF
RACK MOUNT) indicated by a flashing LED on the front of the
master module. The relays in the monitor
J1 OR J2, modules will not switch over to the alarm
PIN 1 OR PIN 2 condition when the BYPASS switch is in the
BYPASS position.
s
Condition Input Alarm LED Alarm Relay Horn Relay CTA Relay Re-Flash Relay
Normal Normal Off Off Off Off Off
First Abnormal Flash On On On On
Alarm
Flash On-Pulse
Subsequent Abnormal On On On
Off-On
Silence Abnormal Flash On Off On On
Reset Abnormal Flash On Off On On
Return to Flash On* Off On On
Normal
Normal
Reset Normal Off Off Off Off Off
Test Normal Off Off Off Off Off
Test with Normal Flash Off On On On
S.D. Bypass
Reset Normal Off Off Off Off Off
’Alarm relay on if in latching (L) operation. Relay is off in non-latching (NL) operation.
Table 3: X87 Manual Reset Sequence
Condition Input Alarm LED Alarm Relay Horn Relay CTA Relay Re-Flash Relay
Normal Normal Off Off Off Off Off
First Abnormal Flash On On On On
Alarm
Subsequent Abnormal On On On On On-Pulse
Off-On
First Abnormal Flash On Off On On
Silence
Subsequent Abnormal On On Off On On
Reset
First Abnormal Flash On Off On On
Subsequent Abnormal On On Off On On
Return to First Normal Flash On* Off On On
Normal Subsequent Normal On On* Off On On
First Normal Off Off Off Off Off
Reset
Subsequent Normal Off Off Off Off Off
Test Normal Off Off Off Off Off
Test with
S.D. Bypass Normal Flash Off On On On
Reset Normal Off Off Off Off Off
’Alarm relay on if in latching (L) operation. Relay is off if in non-latching (NL) operation.
Table 4: X87 First-Alert Manual Reset Sequence
5.6 Input Failure Verification 5.7 Removal of Input Module from System
An input sensor failure can be simulated by It is recommended that the shutdown BYPASS
removing an input lead at the rear terminals of switch on the master module be put in the
the monitor module. Shorting the input terminals BYPASS position before removing or inserting an
of an RTD input will also cause an input failure input module from an on-line system. This
indication. The front-panel SENSOR fail LED will prevents any auxiliary relays from switching over
illuminate and the system horn will sound. Also, into the alarm or shutdown condition. After
the monitor’s alarm function will be inhibited, if inserting the module, press RESET and then,
this option is included. (An internal jumper plug return the shutdown BYPASS switch to the OFF
labeled "NML" or “INH” determines whether or position. Note: The sensor fail circuit will activate
not the alarm function will be inhibited.) When the system’s horn relay, so it will be necessary
the input is properly re-connected, the monitor to silence the horn after insertion of an input
module will return to its normal operating module.
condition. See section 3.4 Wiring Instructions for
procedure to avoid shutdown when repairing an
open input condition.
9
6.0 CIRCUIT DESCRIPTION system V-. The demodulated signal at the
output of buffer amplifier U1-A is applied to the A
6.1 Input Module Models X87-300, -400, -470, and B setpoint circuits, The two setpoint and
-471, -472, -473 (Schematic X87-1000, -1016) logic circuits are similar and only the A setpoint
circuit will be described in detail.
The Model X87 utilizes two input modules,
one for temperature and process monitoring The setpoint comparator, U1-B, discerns the
functions and one for vibration and position difference in the magnitude of the voltages
monitoring. The X87-1000 printed circuit board is applied to resistors R1 and R2. If the signal
used for Models X87-300 and X87-400 Universal voltage from UTA, applied to R1, is smaller than
Mother Boards. The X87-1016 printed circuit the setpoint voltage applied to R2, the output of
board is used for the X87-470 series Vibration UTB will be high (approximately + 11 V) (high
and Position input functions. The modules are setpoint). The output of UTB goes low
identical and have the same nomenclature with (approximately -11 V) when the signal voltage is
the exception of an additional positive or higher than the setpoint voltage. Some setpoint
negative 24 V power supply on the X87-1016 hysteresis, or deadband, is provided by D7, R19
printed circuit board. A different transformer is (or D8 and R20), R29 and R56. Potentiometer
used for T2, and D33 and D34 are added. The R56 adjusts the hysteresis and has a graduated
24 V is accessible at screw terminal 3 with its scale screened on the printed circuit board. The
return common to the input signal, on the setpoint voltage from buffer amplifier UTC is
X87-470 series vibration monitors. applied to R2 and to inverting amplifier UTD. The
output of UTD is available to be selected for
The input module functions with a plug-in signal
display on the master module when the A
conditioning amplifier and, optionally, a plug-in
setpoint switch on the front-panel is pressed.
transmitter, to provide the monitoring functions
for an input. The input module provides isolated The output of U8-B is low when the input is
power for the input amplifier and transmitter, normal and high when the input is abnormal
signal isolation circuits, setpoint circuits with (setpoint exceeded). When the output of U8-B
alarm logic and auxiliary relay contact outputs. goes high, the output of U9-D goes high; the
positive-going signal at U9-D, pin 4, clocks
Each input module has its own power supply flip/flop U10-A. When this clock signal is received
circuits, which are derived from a DC-DC at U10-A, the output of U10-A, pin 13, goes high
converter power supply. The integrated circuit, (alarm condition). The output of U10-A, pin 13, is
U14, C25 and R77, form an oscillator that drives routed to several points on the circuit board. It
VMOS transistor switches Q5 and Q6. The can be connected, via a plug-in jumper, to U9-C,
switches are alternately turned on and off at a providing a ‘'latching” signal for alarm relay K1.
frequency of about 80 to 110 kHz. This causes It also provides a clock signal, through C13, to
currents of alternate polarity to flow through the flip/flop U10-B. (We will return to U10-B.) It goes
primary windings of non-saturating transformer to AND gate U9-A and to OR gate U5-B, through
T2. which the CTA bus is activated. The signal
The isolated voltages that power the plug-in input through C13 also is applied to OR gate U5-A,
amplifiers are derived from windings 8-9 and which causes the horn bus to be pulsed.
10-11. These voltages, + V1, -V1, +VR1 and If the module is connected to one or more other
-VR1, are approximately +9 VDC, - 9 VDC, modules in the first-out group, the voltage level
+ 2.5 VDC and - 2.5 VDC. The + 2.5 V and at connector pin C20 can be either high (the
- 2.5 V reference voltages are provided by module is first in alarm) or low (one or more
reference Zener diodes D28 and D27. inputs in the group are already in alarm). The
The plug-in transmitter voltages are provided by voltage level at connector pin C20 is applied,
windings 4-5 and 7-8. These are + V3, + VR3 through R51, to the D input of U10-B. If this
and - VR3 (approximately + 25 V, + 5 V and voltage is high, the clock pulse received when
-5 V. U10-A went into alarm causes U10-B, pin 1, to go
Transformer winding 9-8 provides a voltage from high and pin 2 to go low. The signal at U10-B, pin
which a - V reference voltage is derived by R75 1, is applied to AND gate U9-B and to transistor
and D31. Amplifier U13 and its associated Q4, which pulls down the ME terminal, causing
components make up a stable +12 VDC supply. any other alarms in its group to come in as
These voltages are referenced to the system’s subsequent alarms.
24 V return (V -) and are utilized in the setpoint The low signal from U10-B, pin 2, inhibits AND
and logic circuits. gate U9-A, preventing alarm LED3 from
The amplifier output signal from pin 9 of the illuminating steadily. At the same time, AND gate
plug-in circuit board is modulated by field-effect U9-B is receiving a high signal at pin 1 and a
transistor Q2 and the primary of transformer T1. flash signal, from the flash bus, at pin 2. Pin 3 of
This signal is demodulated from winding 5-6 of U9-B therefore, goes high and low at the flash
T1 by Q1, R30 and C6 and referenced to the rate and this signal is transmitted through U8-D
10
to LED driver U12-B, causing a flashing alarm integrated circuit U1 and its associated
LED (a “first-up” indication). components. The input signal enters the card at
if ME input/output pin C20 was low when the connector pins 6 ( + ) and 7 (-). Thermocouple
module went into alarm, the clock pulse received amplifiers require a cold junction compensation
at U1C-B has no effect and U10-B, pin 1 stays resistor, which is located on the terminal strip on
low and pin 2 stays high. The high level at pin 2, the chassis connector panel. The reference
routed to U9-A, pin 12, and the high level at junction resistor connects to the plug-in card via
U9-A, pin 13, causes a high level at U9-A, pin 11, connector pins 7 and 8. The input voltage is
and a steady illumination of alarm indicator filtered by R3, C2, R15 and C8, and applied to
LED3 (subsequent alarm). low-drift operational amplifier U1, which is
connected in a non-inverting gain configuration.
The output of U8-B is routed to one input of U4-A The gain-determining resistors are R8, R22 and
and the reset bus is connected to the other the gain adjust control R20. The gain resistor
input. An alarm condition-a high level at U8-B, values are chosen to give an output signal level
pin 10—inhibits the reset signal from being of 1 mV per degree Fahrenheit average over the
transmitted through U4-A. Thus, flip/flops U10-A reference segment of the thermocouple range.
and U10-B can be reset only after the module’s The reference segment is a range of
input has returned to its normal condition. temperature where no gain linearization is done
Since the B setpoint operates in a similar in the master module. Table 5 gives the nominal
manner, the description of the A setpoint gain of the amplifier for each thermocouple and
circuitry is applicable to the B setpoint with the linearization code voltage value. Poten
appropriate changes in the nomenclature. tiometer R1 is provided to allow adjustment of
The sensor-fail-detection circuits, located on the the circuit’s zero offset voltage.
input amplifier modules, drive opto-isolator U3
and front-panel indicator LED1. A sensor-fail ThermocoupleRef. Segment Amp. Gain Lin. Code V
condition causes a low-level signal at the output
of U8-C, which can be used to inhibit either or E -50 to O-C 32.30 1.6 VDC
both setpoints by placing a plug-in jumper in the J -50 to 0°C 37.02 2.0 VDC
A and B INH (inhibit) positions. The sensor-fail K -50 toO°C 47.64 2.4 VDC
signal also causes the system’s horn relay to T -20 to 20 °C 46.57 2.8 VDC
switch over through U5-C and U12-C. Indicator R 250 to 340 °C 185.70 3.2 VDC
LED1 is normally green and changes to a red
S 150 to 230 °C 215.30 3.6 VDC
color to indicate a sensor-fail condition.
The analog signals are selected to be switched Table 5
to the analog “4-”and linearization code busses, The input-failure-detection circuit consists of
through the quad switch circuits in U2. The front U2-A and U2-B and associated components. The
panel INPUT, SETPOINT A and SETPOINT B output of an oscillator, U2-A and its associated
switches provide control signals, which cause components, is coupled to the input of the board
either of these parameters to be routed to the through capacitor C7. When an input is
master module for display. Resistor R13 is connected (a low impedance), the AC signal at
included in the circuit to provide additional the junction of R14 and C7 will be very small. If
isolation between modules, in case two or more the impedance of the input is high enough, the
modules are inadvertently selected at the same AC signal will increase and be rectified and
time. If the remote select option is installed, the filtered by D1 and C6 and applied to the
input and setpoint signals can be selected for input of comparator U2-B. When the impedance
display by the application of a positive voltage of the input source is high enough or when the
(referenced to the system’s V -) in the range of input is open, the voltage at the input of
16-50 VDC via elements D2, D4 and D6, which U2-B will be higher than the voltage at the "+"
are constant current devices and allow readout input, causing the output to go to a negative
selection over this broad voltage range. value near - V1. This will cause the front-panel
The linearization code value is determined by SENSOR fail LED to change from a green to a
resistors R26 and R7. This value actuates a red color. The output of U2-B is routed to the
specific linearizer board in the master module for input module’s mother board via J1, pin 10,
each type of input sensor. (Up to three different causing the system horn to sound and,
sensors can be utilized in one system.) optionally, inhibiting the setpoint(s).
14
The comparator, U1-A and U1-B, make up a 6.11 Digital Panel Meter Model X87-101
“window" detector that responds to the EU (Schematics X83-1005 and X83-1006)
linearization code (4.4 V) and ignores the other The DPM consists of two boards, which are
standard codes. When the EU code is received, joined with “F” posts. One board contains the
the outputs of U1-A and U1-B are high, allowing displays and the other has the power supply and
switches Q1 and Q2 to turn on. One of these A/D converter. Isolated power is derived from
switches will be inhibited from turning on by the the V+ supply using a DC-DC converter, Q1, Q2,
OC/°F switch on the master module. When this
T1 and their associated components. The
switch is in the °C position, the voltage at secondary is rectified to a positive and negative
connector pin 8 is high, U1-C's output is low and voltage and regulated to + 5 V with VR1 and
U1-D's output is high. The low level (-12 V) at - 5 V with Zener diode CR2.
the output of U1-C inhibits switch Q2. Switch Q1
is on, connecting resistor R10 in parallel with The analog-to-digital conversion is accomplished
resistor R19 on the master module, increasing using IC1—a 3%2-digit, dual-slope, A/D
converter. A stable reference voltage for the IC is
the gain of amplifier IC2. When the °C/°F switch
is in the °F position, the voltage at connector taken from the + 5 V supply, using precision
pin 8 is low, U1-C’s output is high and U1-D’s Zener diode, CR7. Resistors R10, R11 and poten
output is low. The low level (-12 V) at the output tiometer R13 divide the voltage and provide a
small adjustment range for calibration purposes.
of U1-D inhibits switch Q1. Switch Q2 is on,
connecting an offset current, through R12, to the IC2 and its components display the units being
summing junction of amplifier IC2 on the master read: “C," “F” or “E” (Celsius, Fahrenheit,
module. This offset current represents -32 engineering units). An optional decimal will be
digits referred to the input of the DPM, removing displayed with "E.” When °F is selected, the
the 32° offset inserted by the °C/°F switch. In output of IC2B goes low and lights the proper
addition, when U1-A and UTB are high, transistor segment for an "F." When °C is selected, the
Q3 is turned on, putting zero volts at connector output of IC2A is low and a "C" is displayed. If
pin 9, which is routed to the °C and °F annun engineering units are displayed, the EU linearizer
ciator driven on the DP, causing an "E" to be board pulls down "C” and "F" and “E” is
displayed. displayed. Also, the output of IC2C will go low
and light up the decimal point, if any.
16
PARTS LIST-THERMOCOUPLE, mA, mV AMPLIFIER
Models X87-S10, -S20
Item Qty. ID Part No. Description Vendor
26 1 D1 1N4148D Diode, Signal Motorola
27 1 D2 1N0457A Diode, Low Leakage Fairchild
28 1 U1 MA714HC Operational Amplifier Fairchild
29 1 ?U2 LM358N Dual Op-Amp National
R12 RI 3
Upscale 68 M 47 M
Downscale 47 M 68 M
Other
E J K T R S 4-20 mA 1-5 V Inputs
R2 28.7 k 35.7 k 45.3 k 45.3 k 324 k 274 k *(40.2 k) *(40.2 k)
R3 4.7 k, 5% 4.7 k, 5% 4.7 k, 5% 4.7 k, 5% 4.7 kr 5% 4.7 k, 5% 4.7 k, 5% 499 k
R4 Not Used Not Used Not Used Not Used Not Used Not Used Jumper Jumper
R5 Not Used Not Used Not Used Not Used Not Used Not Used Not Used 6.34 k
R6 158 k 196 k 249 k 249 k 1.78 M 1.50 M
R7 174 k 200 k 261 k 261 k 1.50 M 1.50 M 100 k 100 k
R8 2.10 k 1.82 k 1.40 k 1.43 k 402 348
Ref. June. Used Used Used Used Used Used Not Used Not Used
Res. X80A209
Ext. Cur Not Used Not Used Not Used Not Used Not Used Not Used 3.125 9 Not Used
Loop Res. W.W.
17
PARTS LIST-VIBRATION INPUT AMPLIFIER
Model X87-S70, -S73, -S74, -S75, -S76, -S77
Item Qty. ID Part No. Description Vendor
13 1 R8 RN55C9092F Resistor, M W, 1 % 90.9 k Mepco
14 1 R3 RN55C1003F Resistor, '/A W, 1 % 100 k Mepco
15 2 R25.18 62PR10K Potentiometer, Ceramic 10 k Beckman
16 1 R7 89PR20K Potentiometer, Ceramic 20 k Beckman
17 1 C3 103A101C20 Capacitor, Ceramic .01/100 V Kemet
18 7 C1,2,4,6,8 105R500C20 Capacitor, Ceramic 1/50 V Sprague
12,13
19 1 C9 335A150T20 Capacitor, Tantalum 3.3/15 V Kernel
20 1 C5 685A350T10 Capacitor, Tanatalum 6.8/35 V Kemet
21 1 C7 Not Used
22 1 TSW-102-08-G-S-RA Right Angle Terminal Strip, Samtec
2 Positions
23 3 D1.2.3 1N457A Diode, Low Leakage Fairchild
Only
24 1 U1 LM392N Dual Comparator National
25 2. U2,U5 LF442CN Dual FET Op Amp National
26 2 U3,U4 LF411CN FET Op Amp National
Use with S73 or S74 (Velocity Input) Module Only
27 1 D4 1N5287 Diode Current Source Motorola
.33 mA Nom.
D4 USED □, NOT USED □
______ N1 Through N8, R21,22,23,24,C10,11, W1 and W2: as required
________________ Values for Transducer “OK” Monitor_______________
X87-S70 Displacement Monitor Input: M600, M606, M665, M668 Probe Driver
28 1 R16 RN55C1001F Resistor, 14 W, 1% 1 k Mepco
29 1 R11 RN55C6041F Resistor, % W, 1 % 6.04 k Mepco
30 1 R14 RN55C9091F Resistor, % W, 1 % 9.09 k Mepco
31 1 R12 RN55C2212F Resistor, % W, 1% 22.1 k Mepco
32 1 R13 RN55C2802F Resistor, 14 W, 1 % 28.0 k Mepco
33 1 R10 RN55C1912F Resistor, '/A W, 1% 19.1 k Mepco
X87-S73, -S74 Velocity (Input: M85 or M86 Vel. Transducer)
34 1 R11 RN55C7501F Resistor, VA W, 1 % 7.5 k Mepco
35 1 R16 RN55C1052F Resistor, % W, 1% 10.5 k Mepco
36 1 R12 RN55C2432F Resistor, % W, 1 % 24.3 k Mepco
37 1 R13 RN55C2552F Resistor, % W, 1 % 25.5 k Mepco
38 1 R10 RN55C1742F Resistor, % w, 1% 17.4 k Mepco
39 1 R14 J0.5O0X0.125 Jumper 0.5 f Squires
X87-S75, -S76, -S77 Acceleration (Input: M98, M99 Accelerometer)
40 1 R16 RN55C1001F Resistor, % W, 1 % 1.0 k Mepco
41 1 R13 RN55C1822F Resistor, * W, 1% 18.2 k Mepco
42 1 R10,14 RN55C9091F Resistor, 14 W, 1 % 9.09 k Mepco
43 1 R11 RN55C1622F Resistor, % W. 1% 16.2 k Mepco
44 1 R12 RN55C8252F Resistor, Y W, 1 % 82.5 k Mepco
18
PARTS LIST-POSITION INPUT AMPLIFIER
Model X87-S78
Item Qty. ID Part No. Description Vendor
1 1 X87-1012 Printed Circuit Board Ronan
2
3 1 R10 RC07GF101J Resistor, 'A W, 5%, 100 ohms A.B.
4 1 R2 RCO7GF392J Resistor, % W, 5%, 3.9 k A.B.
5 1 R21 RC07GF473J Resistor, % W, 5%, 47 k A.B.
6 1 R22 RC07GF825J Resistor, % W, 5%, 8.2 M A.B.
7 1 R20 RN55C3742F Resistor, 1 % M.F., 37.4 k Mepco
8 1 R5 RN55C2433F Resistor, 1 % M.F., 243 k Mepco
9 2 R3,4 RN55C2493F Resistor, 1 % M.F., 249 k Mepco
10 1 R6 RN55C3743F Resistor, 1 % M.F., 374 k Mepco
11
12 1 R7 62PR20K Potentiometer, 20 k Beckman
13 2 06,7 104A101C20 Capacitor, Ceramic, .1/100 V U nitrode
14 1 04 503R101020-0 Capacitor, Ceramic, .05/100 V U nitrode
15 1 03 474A500C20 Capacitor, Ceramic, .47/50 V Corning
16 2 08,9 355A150T20 Capacitor, Tant., 3.3/15 V Kemet
17 2 01,2 685A350T20 Capacitor, Tant., 6.8/35 V Kemet
18 1 D3 1N0457A Diode, Low Leakage Fairchild
19 1 □1 0P220GJ Dual Op-Amp PMI
20 1 U4 LM392N Op-Amp/Comparator National
21
Component Values Determined by Input/Output Scaling
22 5 R1,14,15,16,17_____________________________________
Component Values Determined by Position Limits
23 2 R18.19
Components Used for Inverted Signal Out
24 1 R8 RC07GF473J Resistor, 'A W, 5%, 47 k A.B.
25 1 C5 Jumper
26 1 W1 05JUMPERS .5 x .125 x 22 AWG PVC Jumpers Squires
27 2 R9,10 Not Used
Components Used for Non-inverted Signal Out
28 2 R8,9 El-17 Resistor, W.W., .05%, 11.11 k Elliott
29 1 05 503R101C20-0 Capacitor, Ceramic, .05/100 V Unitrode
30 1 R10 RC07GF101J Resistor, Y W, 5%, 100 ohms A.B.
31 1 W1 Not Used
Components Used for Absolute Value Option
32 3 R12,13,24 RN55C1962F Resistor, 1% M.F, 19.6 k Mepco
33 2 R11.23 RN55C3922F Resistor, 1 % M.F., 39.2 k Mepco
34 2 D1,2 1N4148D Diode, Signal Motorola
35 2 U2,3 uA714HC Op-Amp Fairchild
19
PARTS LIST-FREQUENCY INPUT BOARD
Model X87-S79
Item Qty. ID Part No. Description Vendor
1 1 X87-1018A Printed Circuit Board Ronan
2 1 22-17-2102 Receptacle, Bottom Entry Molex
3 3 4—40x3/16 Screws, Phillips Panhead W. Valley
4 3 #4 Internal Tooth Lock Washer W. Valley
5 1 TSW-102-08-G-S-RA Rt. Angle TC Strip, 2 Positions Samtec
6 1 R16 RC07GF470J Resistor, 'A W, 5%, 47 Ohms A.B. .
7 1 R4 RC07GF821J Resistor, 'A W, 5%, 820 Ohms A.B.
8 2 R17, 19 RC07GF562J Resistor, 'A W, 5%, 5.6 k A.B.
9 2 R1,5 RC07GF331J Resistor, % W, 5%, 3.3 k A.B.
10 1 R14 RCO7GF273J Resistor, 'A W, 5%, 27 k A.B.
11 1 R15 RC07GF334J Resistor, 'A W, 5%, 330 k A.B.
12 1 R4 RN55C1101F Resistor, 'A W, 1% M.F., 1.1 k Dale
13 1 R3 RN55C1003F Resistor, 'A W, 1% M.F , 100 k Dale
14 1 R9 RN55C2432F Resistor, % W, 1% M.F., 24.3 k Dale
15 1 R10 RN55C2003F Resistor, % W, 1% M F., 200 k Dale
16 1 R2 62PR10K Potentiometer, Ceramic 10 k Beckman
17 1 R8 89PR100K Potentiometer, Ceramic 100 k Beckman
18 1 01 331R501M05 Capacitor, DM 330 pF Arco
19 1 C7 104A101C20 Capacitor, Ceramic .1/100 V Kemet
20 4 03,4,5,6 105R500C20 Capacitor, Ceramic 1/50 Sprague
21 1 02 102R101C20 Capacitor, Ceramic .001/100 V Sprague
22 2 D2,3 1N457A Diode, Low Leakage Fairchild
23 1 D4 LM336Z-2.5 Diode, Zener 2.5 V_________ National
24 1 D1 LM336Z-5.0 .Diode, Zener 5.0 V National
25 1 U1 LM393N Dual Comparator National
26 1 U3 LF442CN Dual Op Amp National
27 1 U2 CD4013BE Dual D Flip-Flop RCA
28 1 Q1 VN0106N3 V-MOS FET Supertex
W1, W3 W2, W4
Positive Polarity 10 k, 5% NOT USED
Negative Polarity NOT USED 10 k, 5%
Table 1: Selection of Setpoint Range and Linearization Code Resistors per Input Type.
21
PARTS LIST-MASTER MODULE
Model X87-100B
Item Qty. ID Part No. Description Vendor
20 1 R3 RN55C9761F Resistor, 1 % M.F., 9.76 k Mepco
21 1 R5 RN55C1332F Resistor, 1% M.F., 13.3 k Mepco
22 2 R4.6 RN55C2002F Resistor, 1% M.F., 20.0 k Mepco
23 1 R12 RN55C2942F Resistor, 1 % M.F., 29.4 k Mepco
24 1 R33 RN55C3743F Resistor, 1% M.F., 374 k Mepco
25 1 R40 RN55C4993F Resistor, 1% M.F., 499 k Mepco
26 1 R34 RN55C1002B Resistor, 1% M.F., 10.0 k Mepco
27 1 R30 El-17 Resistor, W.W., .05%, 1.00 k Elliott
28 1 R31 El-17 Resistor, W.W., .05%, 5.00 k Elliott
29 1 R37 El-17 Resistor, W.W., .05%, 6.157 k Elliott
30 1 R32 El-17 Resistor, W.W., .05%, 6.250 k Elliott
31 1 R36 El-17 Resistor, W.W., .05%, 11.11 k Elliott
32 1 R13,14 67YR2K Potentiometer, Trim, 2 k Beckman
33 1 R41 67YR50K Potentiometer, Trim, 50 k Beckman
34 1 C4 820R501M05 Capacitor, Mica, 82 pFd ARCO
35 1 C1 391R501M05 Capacitor, Mica, 390 pFd ARCO
36 1 C2 102R101C20 Capacitor, Ceramic, .001/100 V Ke met
37 3 C6,10,15 104A101C20 Capacitor, Ceramic, .1/100 V Kemet
38 1 C14 105A350T20 Capacitor, Tant., 1/35 V Kemet
39 7 C3,5,7,8,9,11,12 685R350T20 Capacitor, Tant., 6.8/35 V Sprague
40 1 C13 107A400E28 Capacitor, Elect., 100/40 V Mepco
41 3 D5,6,18 1N0457A Diode, Low Leakage Fairchild
42 12 1N4148D
D1,2,3,4,9,10,11,12, Diode, Signal Motorola
13,14,15,16
43 2 D7,8 1N4005D Diode, Rectifier Motorola
44 1 D17 1N0825A Diode, Zener Motorola
45 4 Q1.4,6,7 2N4249 Transistor, PNP Fairchild
46 1 Q5 2N6715-5 Transistor, NPN National
47 2 Q2.3 VN0109N3 Field-Effect Transistor Supertex
48 1 U2 2N4392 FET N-CH Motorola
49 1 U2 LM307N Op-Amp National
50 2 U5,6 A714HC Op-Amp Fairchild
51 2 U7,8 LF411N Op-Amp National
52 1 U4 LM339N Quad Comparator National
53 1 U1 MA723HC Voltage Regulator Fairchild
54 1 U3 CD4047BE Astable Multivibrator RCA
55 1 T1 PE2231X Transformer Pulse Eng.
56 1 S1 MSSA-204N Switch, DPDT Alco
57 3 EB71-SB10GFV Connector Dale
58 1 TSW-1-05-07-G-S Terminal Strip Samtec
59 1 SSW-1-21-02-G-S-RA Socket Strip Samtec •
Vertical Board
60 1 X87-1005A Printed Circuit Board Ronan
61 2 R8.10 RC07GF103J Resistor, % W, 5%, 10 k A.B.
62 6 R2,7,12,13,14,15 RC07GF273J Resistor, 'A W, 5%, 27 k A.B.
63 2 R4,9 RC07GF473J Resistor, 'A W, 5%, 47 k A.B.
64 1 R5 RC07GF104J Resistor, 'A W, 5%, 100 k A.B.
65 2 R1,3 RC07GF224J Resistor, ^A W, 5%, 220 k A.B.
66 1 R6 RCO7GF474J Resistor, 'A W, 5%, 470 k A.B.
67 1 R11 RC07GF684J Resistor, 'A W, 5%, 680 k A.B.
22
PARTS LIST-MASTER MODULE
Model X87-100B
25
PL□ r NE □ PNO □ r INH □ ILO
A A A } 2 ea. A A
l— NL □ L-NDE □ L NC □ LNML □ — NL □
26
PARTS LIST-DUAL-SETPOINT INPUT MODULE
Model X87-400
Item Qty. ID Part No. Description Vendor
31 11 R15,16,17,18,21,22, RC07GF104J Resistor, 1 W, 5%, 100 k A.B.
23,39,47,52,58
32 4 R43,46,48,51 RC07GF224J Resistor, ‘ W, 5%, 220 k A.B.
33 2 R31,34 RC07GF474J Resistor, % W, 5%, 470 k A.B.
34 3 R3,59,80 RC07GF684J Resistor, M W, 5%, 680 k A.B.
35 1 R14 RC07GF475J Resistor, % W, 5%, 4.7 M A.B.
36 1 R76 RC20GF150J Resistor, %2 W, 5%, 15 Ohms A.B.
37
38 2 R29.68 RN55C1000F Resistor, 1% M.F., 100 Ohms Mepco
39 1 R7 RN55C4871F Resistor, 1 % M.F., 4.87 k Mepco
40 1 R13 RN55C4991F Resistor, 1% M.F., 4.99 k Mepco
41 2 R72,77 RN55C2942F Resistor, 1% M.F., 29.4 k Mepco
42 1 R71 RN55C7152F Resistor, 1% M.F., 71.5 k Mepco
43 4 R8,9,10,11 RN55C9532F Resistor, 1 % M.F., 95.3 k Mepco
44 2 R19,54 RN55C8063F Resistor, 1 % M.F., 806 k Mepco
45 2 R20,55 RN55C1104F Resistor, 1% M.F., 1.1 M Mepco
46 8 R1,2,4,5,53,65, RN55C2002B Resistor, .1 % M.F., 20 k Mepco
66,67
47 5 R24,25,26,27,28 See Table 1
48
49 2 R56,57 91BR2K Potentiometer, 2 k__________ Beckman
50 2 R78.79 89PR-20K Potentiometer, 20 k Beckman
51 1 LED1 P405W-RG2-N Light-Emitting Diode, Red/Green Data Disp.
52 2 LED2.3 P205W-BR2-N Light-Emitting Diode, Red Data Disp.
53
54 6 D7,8,15,16,25.26 1N0457A Diode, Low Leakage Fairchild
55 18 01,3,5,9,10,11,12,13, 1N4148D Diode, Signal Motorola
14,17,19,20,21,22,23,29,
30,32
56
57 2 D27,28 LM336Z2.5 Diode, Reference, 2.5 V National
58 3 D18,24,31 LM336Z-5 Diode, Reference, 5.0 V National
59 2 C30.32 335A150T20 Capacitor, Tant., 3.3/15 V Kemet
60 1 C29 390R501M05 Capacitor, Mica, 39 pFd ARCO
61 3 C7,8,25 820R501M05 Capacitor, Mica, 82 pFd ARCO
62 9 C2,5,11,1213,14,16, 104A101C20 Capacitor, Ceramic, .1/100 V Kemet
21,27
63 2 C3.28 474A500C20 Capacitor, Ceramic, .47/50 V Corning
64 1 C9 224R251R10-1 Capacitor, Poly., .22/250 V Mepco
65 2 C1,4 685A350T10 Capacitor, Tant., 6.8/35 V Kernel
66 9 C6,15,17,18,19,20,24, 685R350T20 Capacitor, Tant., 6.8/35 V Sprague
26,31
67 2 C22,23 226R150T20 Capacitor, Tant., 22/15 V Kernel
68 1 C10 105R350T20 Capacitor, Tant., 1/35 V Squires
69
70 2 Q3,4 2N6715-5 Transistor, NPN National
71 2 05,6 VN0106N3 Transistor, VMOS Supertex
72 2 Q1,2 2N4393 Field-Effect Transistor Motorola
73
74 1 U4 CD4001BE Quad, Two-Input NOR Gate RCA
27
+
L □ r NE □ P NO □ r INH □ L □
A A A } 2 ea. A A
_ NL □ l-NDE □ L-NC □ LNML □ 1— NL □
L □ r NE □ I—NO □ P INH □ L □
B B B } 2 ea. B B
_ NL □ LNDE □ I—NC □ LNML □ NL □
Table 1: Jumper Plug Positions
28
PARTS LIST-DUAL-SETPOINT VIBRATION INPUT MODULE
Model X87-470, -471, -472
Item Qty. ID Part No. Description Vendor
1 1 X87-1000C Printed Circuit Board Ronan
2 1 X87D81-1 Front Panel Ronan
3 1 47-10-206-10 Captive Screw Southco
4 1 X87C18 Handle______________________ Ronan
5 1 X87C42 Bracket Ronan
6 1 X87C43 Bracket_____________________ Ronan
7 3 7907B-B-0440-4 Standoff Amatom
8 1 P1 08-911-11 Single Row Header, 8 Positions Aries
9 1 P5 10-053-10 Pin Line Socket Aries
10 2 J1,2,3,4,5,6,7,8,9,10 10-89-1243 Dual Row Header Molex
(10 sections required—cut header
into lengths of 2 positions each—4
total pins per section.)
11 1 3542-2 Pin Jack, Red (+) Pomona
12 1 3542-0 Pin Jack, Black ( —) Pomona
13 1 P3 100-032-053 Connector Panduit
14 5 4—40x3/16" Machine Screw, Slot Pan Head W. Valley
15 5 #4 Inter-Tooth Lock Washer W. Valley
16 1 IDSS-02-S-06 2-Position Cable Strip Samtec
17 1 4—40 X 3/8 Self-Tapping Machine Screw, W. Valley
Phillips, Round Head_______■
18 1 P4 Make from Single-Row Header, 4 Positions Samtec
TSW-110-14-G-S
19 1 P2 10-911-11 Single-Row Header, 10 Positions Aries
20 1 X87B35-1 Membrane Switch Panel T.P.I.
(X87-470)
21 1 X87B35-2 Membrane Switch panel T.P.I.
(X87-474, -476)
22
23 2 R44,49 RC07GF330J Resistor, %4 W, 5%, 33 ohms A.B.
24 1 R70 RC07GF470J Resistor, % W, 5%, 47 ohms A.B.
25 1 R61 RC07GF471J Resistor, % W, 5%, 470 ohms A.B.
26 1 R35 RC07GF821J Resistor, 14 W, 5%, 820 ohms A.B.
27 3 R6,30,69 RCO7GF102J Resistor, M W, 5%, 1.0 k A.B.
28 2 R74,75 RC07GF182J Resistor, % W, 5%, 1.8 k A.B.
29 3 R36,37,73 RC07GF272J Resistor, M W, 5%, 2.7 k A.B.
30 2 R32.33 RCO7GF682J Resistor, % W, 5%, 6.8 k A.B.
31 1 R12 RC07GF472J Resistor, M W, 5%, 4.7 k A.B.
32 2 R63,64 RC07GF103J Resistor, 1 W, 5%, 10 k A.B.
33 3 R45,50,62 RC07GF153J Resistor, M W, 5%, 15 k A.B.
34 2 R40,42 RC07GF393J Resistor, % W, 5%, 39 k A.B.
35 1 R38 RC07GF683J Resistor, % W, 5%, 68 k A.B.
36 11 R15,16,17,18,21,22,23, RC07GF104J Resistor, Ya W, 5%, 100 k A.B.
39,47,52,58
37 4 R43,46,48,51 RC07GF224J Resistor, % W, 5%, 220 k A.B.
38 2 R31.34 RC07GF474J Resistor, % W, 5%, 470 k A.B.
39 3 R3,59,80 RC07GF684J Resistor, % W, 5%, 680 k A.B.
40 1 R14 RC07GF475J Resistor, % W, 5%, 4.7 M A.B.
41 1 R76 RC07GF150J Resistor, % W, 5%, 15 ohms A.B.
29
PARTS LIST-DUAL-SETPOINT VIBRATION INPUT MODULE
Model X87-470, -471, -472
Item Qty. ID Part No. Description Vendor
43 2 R29.68 RN55C10OOF Resistor, 1 % M.F., 100 ohms Mepco
44 1 R7 RN55C4871F Resistor, 1 % M.F., 4.87 k Mepco
45 1 R13 RN55C4991F Resistor, 1% M.F., 4.99 k Mepco
46 2 R72.77 RN55C2942F Resistor, 1% M.F., 29.4 k Mepco
47 1 R71 RN55C7152F Resistor, 1 % M.F., 71.5 k Mepco
48 4 R8,9,10,11 RN55C9532F Resistor, 1 % M.F., 95.3 k Mepco
49 2 R19,54 RN55C8063F Resistor, 1 % M.F., 806 k Mepco
50 2 R20.55 RN55C1104F Resistor, 1% M.F., 1 1 M Mepco
51 8 R1,2,4,5,53,65,66,67 RN55C2002B Resistor, .1 % M.F., 20 k Mepco
52 5 R24,25,26,27,28 See Table 2
53
54 2 R56.57 91BR2K Potentiometer, 2 k Beckman
55 2 R78.79 89PR-20K Potentiometer, 20 k Beckman
56 1 LED1 P405W-RG2-N Light-Emitting Diode, Red/Green Data Disp.
57 2 LED2,3 P205W-BR2-N Light-Emitting Diode, Red Data Disp.
58
59 6 D7,8,15,16,25,26 1N457A Diode, Low Leakage Fairchild
60 18 D1,3,5,9,10,11,12,13,14, 1N4148D Diode, Signal Motorola
17,19,20,21,22,23,29,
30,32
61 2 D27,28_____________ LM336Z2.5 Diode, Reference, 2.5 V National
62 3 D18,24,31 LM336Z5 Diode, Reference, 5.0 V National
63 2 030,32 335A150R20 Capacitor, Tant., 3.3/15 Kemet
64 1 C29 390R501M05 Capacitor, Mica, 89 pfd Arco
65 3 C7,8,25 82OR501M05 Capacitor, Mica, 82 pfd Arco
66 9 C2,5,11,12,13,14,16, 104A101C20 Capacitor, Ceramic, .1/100 V Kemet
21,27
67 2 C3,28 474A500C20 Capacitor, Ceramic, .47/50 V Corning
68 1 09__________________ 224R251R10-1 Capacitor, Polyester, .22/250 Mepco
69 2 C1,4 685A350T10 Capacitor, Tant., 6.8/35 Kemet
70 9 C5,15.17,18,19.20,24, 685R350T10 Capacitor, Tant., 6.8/35 Sprague
26,31________________
71 2 022,23 226R150T2O Capacitor, Tant., .22/15 Kemet
72 1 C10 105R350T20 Capacitor, Tant., 1/35 Sprague
73
74 2 Q1,2 2N4393 Field-Effect Transistor Motorola
75 2 03.4 2N6715-5 Transistor, NPN National
76 2 05,6 VN0106N3 Transistor, V-MOS Supertex
77
78 1 U4 CD4001BE Quad 2-lnput NOR Gate RCA
79 2 U7.10 CD4013BE Dual “D” Flip-Flop RCA
80 1 U2 CD4066BE Quad Switch RCA
81 1 U8 CD4070BE Quad 2-lnput XOR Gate RCA
82 1 U5 CD4071BE Quad 2-lnput OR Gate RCA
83 1 U14 CD4047BE Astable Multivibrator RCA (only)
84 2 U6,9 CD4081BE Quad 2-lnput AND Gate RCA,
Motorola
85 1 U13 LM307N Operational Amplifier National
86 2 U1,11 LM324AN Quad Operational Amplifier National
30
PARTS LIST-DUAL-SETPOINT VIBRATION INPUT MODULE
Model X87-470, -471, -472
Item Qty. ID Part No. Description Vendor
87 1 U12 ULN2004 Trans. Drivers Sprague
88 1 U15 MA78M18CFCor Voltage Regulator, 18 V Fairchild
MC78M18CG
89 1 U3 MCA255 Opto-Isolator Monsanto
90 1 U11 Not Used
91 1 T1 PE2231X Transformer Pulse Eng.
92 1 T2 X83B151 Transformer, Power Merc. Mag.
93
94 1 F1 362.500 Jumper 0.5" Littlefuse
Used □ Not Used □
95 1 F2 362.500 Jumper 0.5 W Littlefuse
Used □ Not Used □
96 2 F1 3529 Fuse Clip Keystone
Used Not Used □
97 2 F2 3529 Fuse Clip Keystone
Used □ Not Used □
98 •2 K1,2 G4D212PUSTV- Relay, DPDT Omron
2DC24
99 2 S1,2 MSSA-204N Switch, DPDT Allo Switch
100 8 65474-004 Jumper Plugs Berg
Remote Selection Option X86-RSO
101 3 D2.4.6 1N5287 Diode, Constant Current Motorola
0‘ L □ । NE □ [—NO □ r INH □
A A A A
I— NL □ LNDE □ — NC □ LNML □
L □ r NE □ P NO □ r INH □
B B B B
I— NL □ 1-NDE □ _ NC □ LNML □
Table 1: Jumper Plug Positions
31
PARTS LIST-DUAL-SETPOINT POSITION INPUT MODULE
Model X87-478
Item Qty. ID Part No. Description Vendor
1 1 X87-1000C Printed Circuit Board Ronan
2 1 X87D81-1 Front Panel Ronan
3 1 47-10-206-10 Captive Screw Southco
4 1 X87C18 Handle Ronan
5 1 X87C42 Bracket Ronan
6 1 X87C43 Bracket Ronan
7 3 9707B-B-O44O-4 Standoff Amatom
8 1 P1 08-911-11 Single Row Header, 8 Positions Aries
9 1 P5 10-053-10 Pin Line Socket Aries
10 2 J1,2,3,4.5,6,7,8,9,10 10-89-1243 Dual Row Header Mo ex
(10 sections required-cut header
into lengths of 2 positions each—4
total pins per section.)__________
11 1 3542-2 Pin Jack, Red ( + ) Pomona
12 1 3542-0 Pin Jack, Black (-)_____________
Pomona
13 1 P3 100-032-053 Connector Panduit
14 5 4—4OX3/16 if
Machine Screw, Slot Pan Head W. Valley
15 5 #4 Inter-Tooth Lock Washer W. Valley
16 1 IDSS-02-S-06 2-Position Cable Strip Samtec
17 1 4—40 X 3/8 Self-Tapping Machine Screw, W. Valley
Phillips, Round Head
18 1 P4 Make from Single-Row Header, 4 Positions Samtec
TSW-110-14-G-S
19 1 P2 10-911-11 Single-Row Header, 10 Positions Aries
20 1 X87B35-1 Membrane Switch Panel T.P.I.
21
22 2 R44,49 RC07GF330J Resistor, %4 W, 5%, 33 ohms A.B.
23 1 R70 RC07GF470J Resistor, % W, 5%, 47 ohms A.B.
24 1 R61 RC07GF471J Resistor, % W, 5%, 470 ohms A.B.
25 1 R35 RCO7GF821J Resistor, % W, 5%, 820 ohms A.B.
26 3 R6,30,69 RC07GF102J Resistor, % W. 5%, 1.0 k A.B.
27 2 R74,75 RC07GF182J Resistor. % W, 5%, 1.8 k A.B.
28 3 R36,37,73 RCO7GF272J Resistor, % W, 5%, 2.7 k A.B.
29 2 R32,33 RC07GF682J Resistor, 14 W, 5%, 6.8 k A.B.
30 1 R12 RCO7GF472J Resistor, % W, 5%, 4.7 k A.B.
31 2 R63.64 RC07GF103J Resistor, % W, 5%, 10 k A.B.
32 3 R45,50,62 RC07GF153J Resistor, % W, 5%, 15 k A.B.
33 2 R40,42 RC07GF393J Resistor, * W, 5%, 39 k A.B.
34 1 R38 RCO7GF683J Resistor, % W, 5%, 68 k A.B.
35 11 R15,16,17,18,21,22,23, RCO7GF104J Resistor, Y W, 5%, 100 k A.B.
39,47,52,58
36 4 R43,46,48,51 RC07GF224J Resistor, 1 W, 5%, 220 k A.B. ■
37 2 R31.34 RC07GF474J Resistor, 14 W, 5%, 470 k A.B.
38 3 R3,59,80 RC07GF684J Resistor, % W, 5%, 680 k A.B.
39 1 R14 RC07GF475J Resistor, % W, 5%, 4.7 M A.B.
40 1 R76 RC07GF150J Resistor, 14 W, 5%, 15 ohms A.B.
41
42 2 R29,68 RN55C10O0F Resistor, 1% M.F., 100 ohms Mepco
43 1 R7 RN55C4871F Resistor, 1 % M.F., 4.87 k Mepco
44 1 R13 RN55C4991F Resistor, 1 % M.F., 4.99 k Mepco
32
PARTS LIST-DUAL-SETPOINT POSITION INPUT MODULE
Model X87-478
Item Qty. ID Part No. Description Vendor
45 2 R72,77 RN55C2942F Resistor, 1 % M.F., 29.4 k Mepco
46 1 R71 RN55C7152F Resistor, 1 % M.F., 71.5 k Mepco
47 4 R8,9,10,11 RN55C9532F Resistor, 1 % M.F., 95.3 k Mepco
48 2 R19.54 RN55C8063F Resistor, 1 % M.F., 806 k Mepco
49 2 R20.55 RN55C1104F Resistor, 1% M.F., 1.1 M Mepco
50 8 R1,2,4.5,53,65,66,67 RN55C2002B Resistor, .1 % M.F., 20 k Mepco
51 5 R24,25,26.27,28 See Table 2
52
53 2 R56.57 91BR2K Potentiometer, 2 k Beckman
54 2 R78.79 89PR-20K Potentiometer, 20 k Beckman
55 1 LED1 P405W-RG2-N Light-Emitting Diode, Red/Green Data Disp.
56 2 LED2.3 P205W-BR2-N Light-Emitting Diode, Red Data Disp.
57
58 6 D7.8.15,16,25,26 1N457A Diode, Low Leakage Fairchild
59 18 D1,3,5,9,10,11,12,13,14, 1N4148D Diode. Signal Motorola
17,19,20,21,22,23,29,
30,32
60 2 D27,28 LM336Z2.5 Diode, Reference, 2.5 V National
61 3 D18,24,31 LM336Z5 Diode, Reference, 5.0 V National
62
63 2 C30,32 335A150T20 Capacitor, Tant., 3.3/15 Kemet
64 1 C29 390R501MO5 Capacitor, Mica, 89 pid Arco
65 3 C7,8,25 820R501M05 Capacitor, Mica, 82 pfd Arco
66 9 C2,5,11,12,13,14,16, 104A101C20 Capacitor, Ceramic, .1/100 V Kemet
21,27
67 2 C3.28 474A500C20 Capacitor, Ceramic, .47/50 V Corning
68 1 C9 224R251R10-1 Capacitor. Polyester, .22/250 Mepco
69 2 C1.4 685A350T10 Capacitor, Tant., 6.8/35 Kemet
70 9 C5,15,17,18,19,20,24, 685R350T10 Capacitor, Tant., 6.8/35 Sprague
26,31
71 2 C22.23 226R150T20 Capacitor, Tant., .22/15 Kemet
72 1 C10 105R350T20 Capacitor, Tant., 1/35 Sprague
73
74 2 Q1,2 2N4393 Field-Effect Transistor Motorola
75 2 Q3,4 2N6715-5 Transistor, NPN National
76 2 Q5,6 VN0106N3 Transistor, V-MOS Supertex
77
78 1 U4 CD4001BE Quad 2-lnput NOR Gate RCA
79 2 U7.10 CD4013BE Dual “D” Flip-Flop RCA
80 1 U2 CD4066BE Quad Switch RCA
81 1 U8 CD4070BE Quad 2-lnput XOR Gate RCA
82 1 U5 CD4071BE Quad 2-lnput OR Gate RCA
83 1 U14 CD4047BE Astable Multivibrator RCA (only)
84 2 U6.9 CD4081BE Quad 2-lnput AND Gate RCA,
Motorola
85 1 U13 LM307N Operational Amplifier National
86 2 U1.11 LM324AN Quad Operational Amplifier National
87 1 U12 ULN2004 Trans. Drivers Sprague
88 1 U15 AA78M18CFC or Voltage Regulator, 18 V Fairchild
MC78M18CG
33
PARTS LIST-DUAL-SETPOINT POSITION INPUT MODULE
Model X87-478
Item Qty. ID Part No. Description Vendor
89 1 U3 MCA255 Opto-Isolator Monsanto
90 1 U11 Not Used
91 1 T1 PE2231X Transformer Pulse Eng.
92 1 T2 X83B151 Transformer, Power Merc. Mag.
93
94 1 F1 362.500 Jumper 0.5" Littlefuse
Used □ Not Used □
95 1 F2 362.500 Jumper 0.5 # Littlefuse
Used □ Not Used □
96 2 F1 3529 Fuse Clip Keystone
Used □ Not Used □
97 2 F2 3529 Fuse Clip Keystone
Used □ Not Used □
98 2 K1,2 G4D212PUSTV- Relay, DPDT Omron
2DC24
99 2 S1,2 MSSA-204N Switch, DPDT Allo Switch
100 8 65474-004 Jumper Plugs Berg
Remote Selection Option X86-RSO
101 3 D2,4,6 1N5287 Diode, Constant Current Motorola
PL □ p NE □ [—NO □ P INH □
A A A A
L NL □ LNDE □ _ NC □ LNML □
L □ I NE □ I—NO □ - INH □
B B B B
L NL □ LN DE □ _ NC □ LNML □
Table 1: Jumper Plug Positions
NOTE: If “ + ” and “ - ” alarms are the same, reconnect end of R1 nearest to edge of board to connector P2,
pin 8 and reconnect end of R53 nearest to S2 connector P2, pin 8.
34
PARTS LIST-TRANSMITTER
Model X87-600
Hem Qty. ID Part No. Description Vendor
1 1 X87-1004B Printed Circuit Board Ronan
2 3 9707B-B-0440-4 Standoff Amatom
3 3 4—40x3/16 Machine Screws, Slot Panhead W. Valley
4 1 JI 22-17-2082 Bottom Entry Connection Molex
5
6 1 R11 RC07GF150J Resistor, ‘ W, 5%, 15 Ohms A.B.
7 1 R3 RC07GF102J Resistor, % W, 5%, 1 k A.B.
8 1 R10 RC07GF222J Resistor, 1 W, 5%, 2.2 k A.B.
9
10 1 R8 RN55C2491F Resistor, 1 % M.F., 2.49 k Mepco
11 1 R9 RN55C75R0F Resistor, 1 % M.F., 75 Ohms Mepco
12 1 R5 RN55C1652F Resistor, 1% M.F., 16.5 k Mepco
13 1 R4 RN55C4753F Resistor, 1 % M.F., 475 k Mepco
14
15 1 R1 89PR50 Potentiometer, 50 Ohms Beckman
16 1 R2 89PR20K Potentiometer, 20 k Beckman
17
18 1 C3 503R101C20-0 Capacitor, Disc., .05/100 V Sprague
19 1 C4 104A101C20 Capacitor, Axial, .1/100 V Kemet
20 1 C2 685A350T20 Capacitor, Tant., 6.8/35 V Kemet
21 1 C1 820R501M05 Capacitor, Mica, 82 pFd ARCO
22
23 1 Q3 2N4249 Transistor, PNP National
24 1 01 2N4393 Field-Effect Transistor Motorola
25 1 02 MJE243 Transistor, NPN Motorola
26 1 6073B Heatsink for Q2 Thermalloy
27 1 U1 LM358N Dual Op-Amp National
28 3 450-3752-01-03-00 or Pinjacks Cam bion
450-3752-01-06-00
29
30 1 360-0017-01-03-00 Jumper Plug Cambion
1-5 V OUTPUT OPTION
31 1 R12 250 Ohms, .1%, RS-1A
32
R6
R7
35
PARTS LIST-LINEARIZER
Model X83-200-100
Item Qty. ID Part No. Description Vendor
1 1 X83-1004 Printed Circuit Board Ronan
2
3 1 R41 RC07GF103J Resistor, 1 W, 5% 10 k A.B.
4 1 R42 RC07GF473J Resistor, % W, 5% 47 k A.B.
5 1 R40 RC07GF225J Resistor, % W, 5% 2.2 M A.B.
6 1 R12 RC07GF515J Resistor, Y W, 5% 5.1 M A.B.
7
8 2 R38.39 RN55C1002B Resistor, .1% M.F., 10.0 k Mepco
9 8 R23,25,27,29,30, RN55C2492 Resistor, 1% M.F., 24.9 k Mepco
32,34.36
10 1 R45 RN55C8060 Resistor, 1% M.F., 806 Mepco
11 3 R3,14,21 RN55C3573 Resistor, 1 % M.F., 357 k Mepco
12
13 1 R7 RN55C9311 Resistor, 1 % M.F., 9.31 k Mepco
14 1 R1 RN55C1962 Resistor, 1% M.F., 19.6 k Mepco
15 1 R10 RN55C1402 Resistor, 1 % M.F., 14.0 k Mepco
16 1 R4 RN55C1432 Resistor, 1% M.F., 14.3 k Mepco
17 1 R17 RN55C1742 Resistor, 1% M.F., 17.4 k Mepco
18 1 R13 RN55C2942 Resistor, 1 % M.F., 29.4 k Mepco
19 1 R15 RN55C4122 Resistor, 1% M.F., 41.2 k Mepco
20 1 R20 RN55C5492 Resistor, 1 % M.F., 54.9 k Mepco
21 2 R16.18 RN55C3573 Resistor, 1% M.F., 357 k Mepco
22
23 1 R37 RN55C1103 Resistor, 1 % M.F., 110 k Mepco
24 1 R35 RN55C1783 Resistor, 1 % M.F., 178 k Mepco
25 1 R9 RN55C3573 Resistor, 1 % M.F., 357 k Mepco
26 1 R33 RN55C2943 Resistor, 1 % M.F., 294 k Mepco
27 1 R5 RN55C7153 Resistor, 1 % M.F., 715 k Mepco
28 1 R31 RN55C5623 Resistor, 1% M.F., 562 k Mepco
29 1 R22 RN55C3403 Resistor, 1% M.F., 340 k Mepco
30 1 R28 RN55C9093 Resistor, 1 % M.F., 909 k Mepco
32 2 R24,26 RN55C1004 Resistor, 1% M.F., 1.0 M Mepco
33
34 1 R5 RN55C7153 Resistor, 1 % M.F., 715 k Mepco
35 4 R2,8,6,19 Not Used
36 1 R43 RN55C1621 Resistor, 1% M.F., 1.62 k Mepco
37 1 R44 RN55C5902 Resistor, 1 % M.F., 59.0 k Mepco
38
39 6 J2,3,5,7,9,11 J0.500x0.125 0.5 "Jumper Squires
PVC22
40 6 J1,4,6,8,10,12 Not Used
41
42 1 C5 1O5R350T20 Capacitor, Tantalum, Sprague
1/35 V
43 4 C1,2,3,4 685R350T20 Capacitor, Tantalum Sprague
6.8/35 V
44 16 CR3,6,7,8,10,11,13. 1N0457A Diode, Low Leakage Fairchild
14,15,16,17,18,19,
20,21,22
45 8 CR1,2,4,5,9,12,23,24 Not Used
36
PARTS LIST-LINEARIZER
Model X83-200-100
Item Qty. ID Part No. Description Vendor
46
47 1 Q1 MPF4392 or FET, N-Channel Motorola
2N4392
48 2 101,2 LM324N Quad Op-Amp National
49 1 IC3 LM393N Dual Comparator National
50 1 IC4 MA714HC Op-Amp Fairchild
PARTS LIST-LINEARIZER
Model X83-200-120
Item Qty. ID Part No. Description Vendor
1 1 X83-1004 Printed Circuit Board Ronan
2
3 1 R41 RC07GF103J Resistor, % W, 5% 10 k A.B.
4 1 R42 RC07GF473J Resistor, % W, 5% 47 k A.B.
5 1 R40 RC07GF225J Resistor, % W, 5% 2.2 M A.B.
6 1 R2 RC07GF155J Resistor, % W, 5% 1.5 M A.B.
7 1 R8 RC07GF185J Resistor, 14 W, 5% 1.8 M A.B.
8 1 R38 Not Used
37
PARTS LIST-LINEARIZER
Model X83-200-120
Item Qty. ID Part No. Description Vendor
34 6 J2,4,6,8,10,12 J0.500X 0.125 0.5’ Jumper Squires
PVC22
35 6 J1,3,5,7,9,11 Not Used
36
37 1 C5 1C5R350T20 Capacitor, Tantalum, Sprague
1/35 V
38 4 C1,2,3,4 685R350T20 Capacitor, Tantalum, Sprague
6.8/35 V
39
40 16 CR1,2,4,5,7,8,10,11. 1NO457A Diode, Low Leakage Fairchild
13.14,15,16,17,18,19,
20
41 8 CR3,6,9,12,21,22, Not Used
23,24
42 1 Q1 MPF4392 or FET, N-Channel Motorola
2N4392
43 2 IC1,2 LM324N Quad Op-Amp National
44 1 IC3 LM393N Dual Comparator National
45 1 IC4 Not Used
38
PARTS LIST-LINEARIZER
Model X83-200-E
Item Qty. 10 Part No. Description Vendor
1 1 X83-1004 Printed Circuit Board Ronan
2
3 1 R41 RC07GF103J Resistor, % W, 5% 10 k A.B.
4 1 R42 RC07GF473J Resistor, 'A W, 5% 47 k A.B.
5 1 R40 RC07GF225J Resistor, 14.W, 5% 2.2 M A.B.
6
7 2 R38.39 RN55C1002 Resistor, 1% M.F., 10.0 k Mepco
8 14 R1,4,7,10,13,17,23, RN55C2492 Resistor, 1% M.F., 24.9 k Mepco
25,27,29,30,32,
34,36
9 2 R15,20 RN55C4992 Resistor, 1 % M.F., 49.9 k Mepco
10 1 R21 RN55C1023 Resistor, 1 % M.F., 102 k Mepco
11 1 R16 RN55C1273 Resistor, 1% M.F., 127 k Mepco
12 1 R14 RN55C1403 Resistor, 1% M.F., 140 k Mepco
13 1 R22 RN55C1473 Resistor, 1% M.F., 147 k Mepco
14 1 R24 RN55C1693 Resistor, 1 % M.F., 169 k Mepco
15 1' R26 RN55C1783 Resistor, 1% M.F., 178 k Mepco
16 1 R18 RN55C2213 Resistor, 1 % M.F., 221 k Mepco
17 1 R28 RN55C2263 Resistor, 1% M.F., 226 k Mepco
18 1 R31 RN55C2373 Resistor, 1 % M.F., 237 k Mepco
19 1 R33 RN55C3243 Resistor, 1 % M.F., 324 k Mepco
20 1 R5 RN55C3573 Resistor, 1 % M.F., 357 k Mepco
21 1 R35 RN55C3833 Resistor, 1 % M.F., 383 k Mepco
22 1 R8 RN55C4873 Resistor, 1 % M.F., 487 k Mepco
23 1 R11 RN55C5903 Resistor, 1 % M.F., 590 k Mepco
24 1 R9 RN55C7683 Resistor, 1 % M.F., 768 k Mepco
25 1 R37 RN55C1783 Resistor, 1% M.F., 178 k Mepco
26 1 R44 RN55C2052 Resistor, 1 % M.F., 20.5 k Mepco
27 1 R45 RN55C8060 Resistor, 1 % M.F., 806 ohm Mepco
28 1 R43 RN55C2801 Resistor, 1 % M.F., 2.8 k Mepco
29
30 5 R2,3,6,12,19 Not Used
31 1 C5 105R350T20 Capacitor, Tantalum, Sprague
1/35 V
32 4 C1,2,3.4 685R350T20 Capacitor, Tantalum, Sprague
6.8/35 V
33
34 16 CR1,2,4,5,7,8,10, 1N0457A Diode, Low Leakage Fairchild
11,13,14,15,16,17,
18,19,20
35 8 CR3,6,9,12,21,22, Not Used
23,24
36
37 1 Q1 MPF4392 or FET, N-Channel Motorola
2N4392
38 2 IC1,2 LM324N Quad Op-Amp National
39 1 IC3 LM393N Dual Comparator National
40 1 IC4 A714HC Op-Amp Fairchild
41 6 J2,4,6,8,10,11 J0.500X0.125 0.5" Jumper Squires
PVC22
42 6 J1,3,5,7,9,12 Not Used
39
PARTS LIST- LINEARIZER
Model X83-200-J
Hem Qty. ID Part No. Description Vendor
1 1 X83-1004 Printed Circuit Board Ronan
2
3 1 R41 RC07GF103J Resistor, 1 W, 5% 10 k A.B.
4 1 R42 RC07GF47J Resistor, % W. 5% 47 k A.B.
5 1 R40 RC07GF225J Resistor, % W, 5% 2.2 M A.B.
6 1 R28 RC07GF275J Resistor, 14 W, 5%, 2.7 M A.B.
7
8 2 R38,39 RN55C1002 Resistor, 1 % M.F., 10.0 k Mepco
9 13 R1,4,7,10,17,23, RN55C2492 Resistor, 1 % M.F., 24,9 k Mepco
25,27,29,30,32
34,36
10 3 R13,15,20 RN55C4992 Resistor, 1 % M.F., 49.9 k Mepco
11 2 R 18,37 RN55C1053 Resistor, 1% M.F., 105 k Mepco
12 1 R21 RN55C1543 Resistor, 1% M.F., 154 k Mepco
13 1 R16 RN55C1743 Resistor, 1% M.F.,.174 k Mepco
14 1 R35 RN55C1783 Resistor, 1% M.F., 178 k Mepco
15 1 R22 RN55C1823 Resistor, 1 % M.F., 182 k Mepco
16 1 R14 RN55C2003 Resistor, 1% M.F., 200 k Mepco
17 1 R33 RN55C2553 Resistor, 1 % M.F., 250 k Mepco
18 1 R24 RN55C2613 Resistor, 1 % M.F., 261 k Mepco
19 1 R26 RN55C4223 Resistor, 1 % M.F., 422 k Mepco
20 1 R8 RN55C4873 Resistor, 1 % M.F., 487 k Mepco
21 1 R11 RN55C4993 Resistor, 1 % M.F., 499 k Mepco
22 1 R31 RN55C5903 Resistor, 1 % M.F., 590 k Mepco
23 1 R9 RN55C7503 Resistor, 1 % M.F., 750 k Mepco
24 1 R5 RN55C3013 Resistor, 1 % M.F., 301 k Mepco
25 1 R44 RN55C1962 Resistor, 1% M.F., 19.6 k Mepco
26 1 R45 RN55C8060 Resistor, 1% M.F., 806 ohm Mepco
27 1 R43 RN55C3571 Resistor, 1 % M.F., 3.57 k Mepco
28
29 5 R2,3,6,12,19 Not Used
30 1 C5 105R350T20 Capacitor, Tantalum, Sprague
1/35 V
36 4 C1,2,3,4 685R350T20 Capacitor, Tantalum, Sprague
6.8/35 V
37
38 16 CR1,2,4,5,7,8,10,11, 1N0457A Diode, Low Leakage Fairchild
13,14,15,16,17,18,
19,20
39 8 CR3,6,9,12,21,22, Not Used
23,24
40
41 1 Q1 MPF4392 or FET, N-Channel Motorola
2N4392
42 2 IC1,2 LM324N Quad Op-Amp National
43 1 IC3 LM393N Dual Comparator National
44 1 IC4 A714HC Op-Amp Fairchild
45 6 J2,4,6,8,10,12 JO.500 x 0.125 0.5" Jumper Squires
PVC22
46 6 J1,3,5,7.9,11 Not Used
40
PARTS LIST-LINEARIZER
Model X83-200—K
Item Qty. ID Part No. Description Vendor
1 1 X83-1004 Printed Circuit Board Ronan
2
3 1 R41 RC07GF103J Resistor, 1 W, 5% 10 k A.B.
4 1 R42 RC07GF47J Resistor, % W, 5% 47 k A.B.
5 1 R40 RC07GF225J Resistor, Y W, 5% 2.2 M A.B.
6
7 1 R24 RN55C8253F Resistor, 1% M.F., 825 k Mepco
8 2 R38.39 RN55C1002 Resistor, 1% M.F., 10.0 k Mepco
9 13 R1,4,7,10,17,23, RN55C2492 Resistor, 1% M.F., 24.9 k Mepco
25,27,29,30,32
34,36
10 3 R13,15,20 RN55C4992 Resistor, 1% M.F., 49.9 k Mepco
11 2 R21 RN55C1023 Resistor, 1% M.F., 102 k Mepco
12 1 R8 RN55C9313F Resistor, 1% M.F., 931 k Mepco
13 1 R37 RN55C8252 Resistor, 1% M.F., 82.5 k Mepco
14 1 R16 RN55C1213 Resistor, 1% M.F., 121 k Mepco
15 2 R18.33 RN55C1373 Resistor, 1 % M.F., 137 k Mepco
16 2 R14.18 RN55C1473 Resistor, 1 % M.F., 147 k Mepco
17 1 R22 RN55C1623 Resistor, 1 % M.F., 162 k Mepco
18 1 R5 RN55C2213 Resistor, 1% M.F., 221 k Mepco
19 1 R28 RN55C2943 Resistor, 1% M.F., 294 k Mepco
20 1 R11 RN55C3653 Resistor, 1% M.F., 365 k Mepco
21 R26 RN55C4533 Resistor, 1 % M.F., 453 k Mepco
22 1 R31 RN55C6043 Resistor, 1 % M.F., 604 k Mepco
23 1 R35 RN55C1373 Resistor, 1 % M.F., 137 k Mepco
24 1 R44 RN55C1872 Resistor, 1% M.F„ 18.7 k Mepco
25 1 R45 RN55C8060 Resistor, 1 % M.F., 806 ohm Mepco
26 1 R43 RN55C4421 Resistor, 1 % M.F., 4.42 k Mepco
27
28 6 R2,3,6,9,12,19 Not Used
29 1 C5 105R350T20 Capacitor, Tantalum, Sprague
1/35 V
30 4 C1,2,3,4 685R350T20 Capacitor, Tantalum, Sprague
6.8/35 V
31
32 16 CR1,2,4,5,7,8,10,11, 1N0457A Diode, Low Leakage Fairchild
13,14,15,16,17,18,
19,20
33 8 CR3,6,9,12,21,22, Not Used
23,24
34
35 1 Q1 MPF4392 or FET, N-Channel Motorola
2N4392
36 2 IC1,2 LM324N Quad Op-Amp National
37 1 IC3 LM393N Dual Comparator National
38 1 IC4 MA714HC Op-Amp Fairchild
39 6 J2,3,6,8,9,11 JO.500 x 0.125 0.5" Jumper Squires
PVC22
40 6 J1,4,5,7,10,12 Not Used
41
PARTS LIST-LINEARIZER
Model X83-200-T
Item Qty. ID Part No. Description Vendor
1 1 X83-1004 Printed Circuit Board Ronan
2
3 1 R41 RC07GF103J Resistor, 1 W, 5% 10 k A.B.
4 1 R42 RC07GF473J Resistor, % W, 5% 47 k A.B.
5 1 R40 RC07GF225J Resistor, W W, 5% 2.2 M A.B.
6
7 1 R4 RN55C8251 Resistor, 1 % M.F., 8.25 k Mepco
8 1 R22 RN55C2262 Resistor, 1 % M.F., 22.6 k Mepco
9 2 R38.39 RN55C1002 Resistor, 1 % M.F., 10.0 k Mepco
10 16 R1,7,10,13,15,17, RN55C2492 Resistor, 1 % M.F., 24.9 k Mepco
20,23,24,25,27,
29,30,32,34,36
11 1 R26 RN55C4022 Resistor, 1 % M.F., 40.2 k Mepco
12 2 R31.33 RN55C9532 Resistor, 1 % M.F., 95.3 k Mepco
13 1 R35 RN55C1333 Resistor, 1% M.F., 133 k Mepco
14 1 R37 RN55C1693 Resistor, 1% M.F., 169 k Mepco
15 1 R21 RN55C1823 Resistor, 1 % M.F., 182 k Mepco
16 1 R28 RN55C21Q3 Resistor, 1% M.F., 210 k Mepco
17 1 R16 RN55C3013 Resistor, 1 % M.F., 301 k Mepco
18 1 R3 RN55C4533 Resistor, 1 % M.F., 453 k Mepco
19 2 R9,18 RN55G5493 Resistor, 1 % M.F., 549 k Mepco
20 1 R14 RN55G6043 Resistor, 1 % M.F., 604 k Mepco
21 1 R19 RN55G6813 Resistor, 1 % M.F., 681 k Mepco
22 1 R12 RN55C7873 Resistor, 1 % M.F., 787 k Mepco
23 1 R6 RN55C1004 Resistor, 1 % M.F., 1 M Mepco
24 1 R44 RN55C1822 Resistor, 1 % M.F., 18.2 k Mepco
25 1 R45 RN55C8060 Resistor, 1 % M.F., 806 ohm Mepco
26 1 R43 RN55C5231 Resistor, 1 % M.F., 5.23 k Mepco
27
28 4 R2,5,8,11 Not Used
29
30 1 C5 105R350T20 Capacitor, Tantalum, Sprague
1/35 V
31 4 C1,2,3,4 685R350T20 Capacitor, Tantalum, Sprague
6.8/35 V
32
33 16 CR3,6,9,12,13,14, 1N0457A Diode, Low Leakage Fairchild
15,16,17,18,19,
21,20,22,23,24
34 8 CR1,2,4,5,7,8,10,11 Not Used
35 1 Q1 MPF4392 or FET, N-Channel Motorola
2N4392
36 2 IC1,2 LM324N Quad Op-Amp National
37 1 IC3 LM393N Dual Comparator National
38 1 IC4 pA714HC Op-Amp Fairchild
39 6 J2,4,6,7,9,11 J0.500x.125 0.5" Jumper Squires
PVC22
40 6 J1,3.5,8,10,12 Not Used
42
PARTS LIST-LINEARIZER
Model X87-200-R
Item Qty. ID Part No. Description Vendor
1 1 X83-1004 Printed Circuit Board Ronan
2 1 R41 RC07GF103J Resistor, % W, 5%, 10 k A.B.
3 1 R42 RC07GF473J Resistor, % W, 5%, 47 k A.B.
4 1 R40 RC07GF225J Resistor, % W, 5%, 2.2 Meg A.B.
5
6 1 R45 RN55C8060F Resistor, 1 % M.F., 806 Ohms Mepco
7 8 R23,24,27,29,30,32,34,36 RN55C4991F Resistor, 1 % M.F., 4.99 k Mepco
8 1 R43 RN55C6041F Resistor, 1 % M.F., 6.04 k Mepco
9 1 R1 RN55C6651F Resistor, 1% M.F., 6.65 k Mepco
10 1 R7 RN55C9311F Resistor, 1 % M.F., 9.31 k Mepco
11 1 R10 RN55C1212F Resistor, 1% M.F., 12.1 k Mepco
12 1 R4 RN55C1502F Resistor, 1% M.F., 15.0 k Mepco
13 1 R44 RN55C1742F Resistor, 1 % M.F., 17.4 k Mepco
14 1 R17 RN55C1822F Resistor, 1 % M.F., 18.2 k Mepco
15 1 R13 RN55C2262F Resistor, 1 % M.F., 22.6 k Mepco
16 1 R15 RN55C2742F Resistor, 1% M.F., 27.4 k Mepco
17 1 R37 RN55C2872F Resistor, 1 % M.F., 28.7 k Mepco
18 1 R20 RN55C4872F Resistor, 1 % M.F., 48.7 k Mepco
19 1 R35 RN55C4532F Resistor, 1 % M.F., 45.3 k Mepco
20 1 R33 RN55C5622F Resistor, 1 % M.F., 56.2 k Mepco
21 1 R31 RN55C6982F Resistor, 1 % M.F., 69.8 k Mepco
22 1 R28 RN55C8252F Resistor, 1 % M.F., 82.5 k Mepco
23 1 R26 RN55C1023F Resistor, 1% M.F., 102 k Mepco
24 1 R24 RN55C1133F Resistor, 1 % M.F., 113 k Mepco
25 1 R22 RN55C1243F Resistor, 1 % M.F., 124 k Mepco
26 1 R11 RN55C5762F Resistor, 1 % M.F., 57.6 k Mepco
27 7 R2,5,8,14,16,18,21RN55C5492F Resistor, 1 % M.F., 54.9 k Mepco
28 1 R39 RN55C4643F Resistor, 1 % M.F., 464 k Mepco
29 6 R33,6,9,12,19,38 Not Used
30
31 6 42,4,6,8,10,12 05JUMPERS .5X.125X22 AWG Squires
PVC Jumpers
32 6 J1,3,5,7,9,11 Not Used
33
34 1 C5 105R350T20 Capacitor, Tant., ,1 mfd/35 V Sprague
35 4 C1,2,3,4 685R350T20 Capacitor, Tant., 6.8 mfd/35 V Sprague
36 16 1N0457A
CR1,2,4,5,7,8,10,11,13, Diode, Low Leakage Fairchild
14,15,16,17,18,19,20
37 8 CR3,6,9,12,21,22,23,24 Not Used
38
39 1 Q1 2N4392 Field-Effect Transistor Motorola
40 2 IC1,2 LM324N Quad Op-Amp National
41 1 IC3 LM393AN National
42 1 IC4 Not Used
(Jumper pin 6 to pin 7 of IC4)
43
PARTS LIST- LINEARIZER
Model X87-200-S
Item Qty. ID Part No. Description Vendor
1 1 X83-1004 Printed Circuit Board Ronan
2 1 R41 RC07GF103J Resistor, W W, 5%, 10 k A.B.
3 1 R42 RC07GF473J Resistor, % W, 5%, 47 k A.B.
4 1 R40 RC07GF225J Resistor, % W, 5%, 2.2 Meg A.B.
5
6 1 R45 RN55C8060F Resistor, 1 % M.F., 806 Ohms Mepco
7 8 R23,25,27,29,30,32,34,36 RN55C4991F Resistor, 1 % M.F., 4.99 k Mepco
8 1 R43 RN55C6811F Resistor, 1 % M.F., 6.81 k Mepco
9 1 R1 RN55C8871F Resistor, 1 % M.F., 8.87 k Mepco
10 1 R7 RN55C1402F Resistor, 1% M.F., 14.0 k Mepco
11 1 R44 RN55C1652F Resistor, 1% M.F., 16.5 k Mepco
12 1 R37 RN55C8061F Resistor, 1 % M.F., 8.06 k Mepco
13 1 R10 RN55C2102F Resistor, 1% M.F., 21.0 k Mepco
14 1 R4 RN55C2872F Resistor, 1 % M.F., 28.7 k Mepco
15 1 R35 RN55C3162F Resistor, 1 % M.F., 31.6 k Mepco
16 2 R17.33 RN55C3652F Resistor, 1 % M.F., 36.5 k Mepco
17 1 R31 RN55C3922F Resistor, 1 % M.F., 39.2 k Mepco
18 2 R13.28 RN55C4422F Resistor, 1% M.F., 44.2 k Mepco
19 1 R15 RN55C5362F Resistor, 1% M.F., 53.6 k Mepco
20 1 R26 RN55C5902F Resistor, 1 % M.F., 59.0 k Mepco
21 1 R24 RN55C6492F Resistor, 1 % M.F., 64.9 k Mepco
22 1 R22 RN55C7152F Resistor, 1% M.F., 71.5 k Mepco
23 1 R20 RN55C8662F Resistor, 1 % M.F., 86.6 k Mepco
24 8 R2,5,8,11,14,16,18,21 RN55C1003F Resistor, 1 % M.F., 100 k Mepco
25 1 R39 RN55C8872F Resistor, 1 % M.F., 887 k Mepco
26 6 R3,6,9,12,19,38 Not Used
27
28 6 J1,3,5,7,9,11 Not Used
29 6 J2,4,6,8,10,12 05JUMPERS .5X.125X22 AWG Squires
PVC Jumpers
30
31 1 C5 105T350T20 Capacitor, Tant., 1/35 V Sprague
32 4 C1,2,3,4 685R350T20 Capacitor, Tant., 6.8/35 V Sprague
33 16 CR1,2,4,5,7,8,10,11,13, 1N0457A Diode, Low Leakage Fairchild
14,15,16,17,18,19,20
34 8 CR3,6,9,12,21,22,23,24 Not Used
35
36 1 Q1 2N4392 Field-Effect Transistor Motorola
37 2 IC1,2 LM324N Quad Op-Amp National
38 1 IC3 LM393AN Dual Comparator National
39 1 IC4 Not Used
(Jumper pin 6 to pin 7 of IC4)
40
44
PARTS LIST-LIN EAR IZER
Model X83-200-EU
hem Qty. 10 Part No. Description Vendor
1 1 X83-1031 Printed Circuit Board Ronan
2
3
4
5 1 R17 RC07GF472J Resistor, % W, 5% 4.7 k A.B.
6 2 R1.15 RC07GF103J Resistor, % W. 5% 10.0 k A.B.
7 1 R16 RC07GF153J Resistor, % W, 5% 15 k A.B.
8 4 R6,9,11,14 RC07GF104J Resistor, 1 W, 5% 100 k A.B.
9 1 R2 RC07GF225J Resistor, % W, 5% 2.2 M A.B.
10
11 1 R4 RN55C8060 Resistor, 1 % M.F., 806 ohms Mepco
12 1 R8 RN55C2211 Resistor, 1% M.F., 2.21 k Mepco
13 1 R5 RN55C8451 Resistor, 1 % M.F., 8.45 k Mepco
14 1 R3 RN55C1502 Resistor, 1% M.F., 15.0 k Mepco
15 1 R7 RN55C1303 Resistor, 1% M.F., 130 k Mepco
16 1 R12 RN55C3743 Resistor, 1 % M.F., 374 k Mepco
17 1 R13 RN55C1182 Resistor, 1% M.F., 11.8 k Mepco
18
19 1 R10 EH7 Resistor, W.W., 12.45 k± .1 % Elliott
20
21 1 C1 105R350T10 Capacitor, Tantalum, Sprague
1/35 V
22 2 C2,3 685R350T10 Capacitor, Tantalum, Sprague
6.8/35 V
23
24 4 D1,2,3,4 1N4148D Diode, Signal Fairchild
25
26 2 Q12, 2N4392 FET, N-Channel Motorola
27 1 Q3 2N6715 Transistor, NPN National
28 1 U1 LM339N Quad Comparator National
45
o
-o*3
gmi J + Cll RSE (+23V) +18
R6S
Krz—1 1
15K
- +3 ik R?l
24* 16*+ Htes—
187Seu l Lr36z-s LS,A IBTPASS)
a
H]-A.K 24V+
(
C32 F2
C26
3H 11 I R#
VH
i Des _ "I DLD
BLDGN3
6.B
/15 C1?
Dia
d f LH3362-5 is
I
501
ledal
14857A D19
70H1BC
M RSI
- 433 A J? C22
£zeeha
C27 UI5 /35
UM 14K
1- 478 Gn
+i2V2 01
925, ch res H. 424
R:# 1 s
24VC
It 1
227 444785 US7a €24 »012
25. 4K 9,0e-
• =- $,9.35 tzV NN 0
J 1% 132
*
tiv) R25
-[ IT
A
VN LATC LATCH
D -5V2
T ay
F| A J6 C24
01E6N3 -0-ve i.ek © +VI(SV)
t
< M,C*
Cw
K23,2.7k
-o +VR,
<«.SV) IIH JE 5. “has
412*2, U12.G H
•-013
A2G 504
TP3 C22
22/15 U36Z-Z.5 D2B R3 U,D 9 , 13
1/2A"
‘Jut,
13 »01
EBAK C 2t-
LED1 $*,
T2 i
*83815. +LC3 Lt
= 127
2 : LA3SZ-2.5
“2* .^15
9
4813R
IB.A 6FD3
shso res T za/is R?4 2 12 D
♦VI +WR]
- o -VRI R2t
R I£
—{hP_ 6 -N 12V2
+12V2
i : ex t-2.5V) RI
ZeK
C2. U1,E
104K + U8.B 72.7
P36
fl tuu
D10 o -VI .1* 2
Al
oali y8 _",2
19V1 219 0? -------- 1 -12
HI
I R35
R2 U.CCF1) 12
I [ 2 LG
CHJ7HHE FAIL
20
.IX
23 RE UI?.B
-a
MCA +12V me, a +12V2
i C6 82@ OHH
255 PPR %i 2
*0- CS
1 FAIL 15 •.1H 14157A
88,2 HTS. .
AKS =2* +1ZV2 R51 Ioz
•u
1
INPUT. IL I*H
■ 2 co
—-0« PLUG-IN INPUT 6 F14
?&&
R2B A
W
20, 10
AMPLIFIER .7M e. ree
: RX 04
7
4 C10 X87-1001 RTD AIP
R79 ‘ S.P.A.
+!2v2 2N6715
0—X X87-1002 T/C ArP
T2-15 T2-5
IS
Di4 ’
[ 6.6/35
g 20< 3 R49
D .F I
A1f V' D13! 113
9 C8 R24 +12V2
02 0i
A 6
—get
0—6 21393 = B2PF 2N4333 = 92PF R4 U4 R39
P3 5., 2k
& Le,B
I U1,A
I S
R2
—ft 1 P34
476 «t
I2j
Ul,C
-5v2
14
RS
1 9r
20K, , 1% re.4-10
RST-—0
E
R3B
-
A22
RSI
n
C3 5eK
f
.22 C29 39Fr
-1)----
s.a/3ST
Ct j
6.8/32 -v2 1 20K
.1%
10
•i ,D B £13c04061
P48
BE *
Cl?
1
-VR1 -VI
+l2Ve
+12V2
2A =
T—2A
•12V2 l
= 2A “I 224K
SN
9 C
‘U6,D
‘FAIL’
use
1/35
O. R2? A 13-—-
RE?
&v4 i2]“
* Ja
4 WJENA
RES 5
2tK,.1%
S.P.B
3+ 4 2= 2,.I%
R53
2..!%
R5B R59 M,, ULZ.C 1138,12
f.—
Y- 5
I
n2,C
*10
»HN
ZK.. 12 Uli,
S.P.B,
R78 -
20K is
2. G.B/35 RE5
9
CI5U11,C
GBOK
U,B4
RSe.SGKK 6
nt RI?
R1S P.B-3
1and 12, IE
13
CD48?)
BE
15
AK
%crA
- 2A 12
R25 A C30 .0; DIS
[au57a H 5
U
D
NON1
LATCH
IBKK 112. D
L
C1S— LATO
T2-5 +R3 +V3 13 14
-52
'a
-V2
is 80K,1%
VPP, +s “
-K wl o'
-5
HI, 1 S2
cze
25"
R47
Thos » BYPASS
-2k
-47
yo 24V+ NC.
a3
I
--- 44-4- -2A P6B
1.In,1% —
12
LN437A
4,D
U
V-
L[
cie,
R45 03
216715
Gt re B
cze as
—»-0u
l
I
I 2K 3
I
RS? 5 HTS. 6
v
2
15K
012 3 <2
1 -)(
-20 SIG
Pi.di
V- R44
P33 DI PLUG-IN
TRANSMITTER
X87-1004
[—-8-
XTTR
S-P.A.
INPUT 2;
t
•izV2 DI 13 33
6
v12,€
—901
c30 sa
t SOB
----->—2 IS 24V
I R
I I
CLTPUT +12V2
S.P.E.
IN
IC CO
ICUT V- Ut2,F
R3? wod" f
I 1K 13 +12V
# Cie
3] INUT
3
SPA 3
3
Ia
4066
2 R12 .. LE
15
ID
2.71
4 2-7 4 +12l2Y2
Ri3 224K
"%
I
I
- 5 *12 L.J 1N5207S
Mos -r
5 S.P.B
12
»N
3r
IP 4.99K, 1%, N
Ri2
>ML iB.B
kro
1£
R22
3 1+12V2
R2 F1
-»
uif,a
U7,R
w-T
luls
+1CIS
TEST
»A«
C12
DA
6
i IN
+C
401
4.7 % CODE A32
6.8/35
WH S.P.A.O-< R26:
-VR3 SL.
R13
7.32K
IX
R12 2 8
W
R2 1
+VI 10K
R15
10K
f 3
U2A
l
BSP D1 R14
-200 1N4148 s 2.49K
3 R8
1% 5 R22
RS
A. D2
LM336Z
A
6
U2B
7
LM392N
j 22M
10 SENS
FAIL
-2.5 4
01 02 RIG
2N4243 2N4249 75 +V1
IX -VI
1
R3 C5
6.8K
—
CS
« -G
J1
—
4.7K
R4
Cl _
5 8
3.3/15
7
1 R5
SIGNAL
UIA WW 9
.001T 6 47 OUT
t C2 -L C3 R10 A D3
’ 6.8/35 1N457A
T -1 A
INPUT
R6
4
1
3
RI
ZERO
200
-
4.7K
RI?
C4 _L
.001|
3
2
U1B
1
Rie
4.87K
IX P
3
R21
GAIN
5K
+ LH358N
C8 R7 4 R19 R20
4= C? 4.87K 12.4K
<— ----- 7 W 3.3/15 IX 1%
I
C10 I
<----- J RI 1
A10 COM
. CG
<- -8 +[ 3.3/15
1
1 4 5
-VI GND
6 8
R14 Di
7 2
U2A -WW *
5 1 SENS
X Cl
".01
+4 LM358N 1K
=C6
R19
100K
3
U2B 10 FAIL
1
R11 R17 IX
100K 4.99K
R12 C7
-VI —WW -
.22 +V1
R13
+V1 -W C4 —
-*IH- D2
3.3/15
1N457A
C6 R3 R15 3 7
<------- ----- 6 NW -
I
R21
r
INPUT
R5 . C2
4.7K
T 6.8/35 C8
C3
.001 2
Ul
4
6
uA?14HC
-WW
1K
3 R20
SIGNAL
OUT
X C9
I
4 72P
00 C8 L. 6.8/35
--+
C5 T•i SK
GAIN
«------- >
1
----- 7
— C10
3.3/15
1 R22
64.9K
$64
C10 I 1/35
R4 R6 IX
«------J A A
+VR1
RB
A10 R7 3 RI
<<- -8 MW -s P i89PR
m.10K
1
J1 ZERO
RIB 1
i
I 200
IX
-VRI
3
-VI
4 5
GND
nd —
20.4K
C2 17, D
DS Ld IMPA
1N457A
De
-I
.001
-12V
14
10
U---------------
6•
* 3
02
Ri R4 03
3
220 I/2W UI 10 20.@K LE2 6 01 82FF •?
10071 2N4249 3 6.8/35
3 uk IX CD □1
r
3 16 1N457A
A L4 72301 4 1K
H 4
1
2 R3 R12 4047BE
5
9.76k 29.4k
I% 2 03 04 5
RB
4
I
VNLO9N3
4
5 9 V2- 2
ZL
100 R.l,1OK
R5 B912 D L4D
Cl
— 133K P€223 IX
V2- V2-
350f 3 V2-
A— Rl3
]
1 2K +12V v+ V2-
R15 0? CI3
W —H— —I
s 3
+12V
+12V RIG R18 22 IN25 100/40
+12v
V2- R14
R43
Ire
10K
120K LOK a : R84aa R24
47K
R22
LOEK
R35 2K 02 R21 V2-
3.MK
9.09K £ CS G 27K
214219
C14 =
C12
*y R30
6. 6/35
1 LEDI
$ R17
470<
Lia
133s 4 —27K
19
L4B
3
13
Aesr
f—
1/35
5.8/35. C10 IK
R44
-IF —W—
1 .45%
k 10k
BYPASS
- LED
: C5
6.0/35 V+
R20
12
SIG+
A
P39
W
3
R34
H.W. R45 100K
T $ R19
27K
10K U7 .6 2 R31 L.BK
W V2- V2-
2
LFIILI
LOK L6 6
5K
2 R46 9
R40
499Kd
R36
11 . ] IK
t .05%
W.W.
+12V
$.05%
W.W.
US
6 A 014
I—
47K
8
U4C
14
72 BYPASS
R38 R32 12V
VI- R4 1 CH 0152:
Sok 6.25K □ 10
(SIG-),
121 3 ZERO * .054 —# +:2V
-# A"
C! 1
R37
F33
W.W,
6.6/35 1 +12V
(O
—*- -12V — Ga R28
I 6.0/35
6 157K
? 05X
W.W,
-12V
[2H2—0) -12V
374 K
J
19
I SI
V?-.
¥+ &
6.B/35 1CK
04
R25
10K
R47
+12V
-12V 45-616 •C FSS 4
D?-—ot 2N4299
lOK
+12V-
।—E-&S N.LoD R27
2874x
R50
C 05
2N71S
C6
21249
] 3 E 0.6
LB
Die
1NS7A D
L
OB2+4332__
1.8K
?
-12V £5
—110-01010
R29
!OK 2
DE/
1N825A
L.BK
R26
10K
$ R48
27K
F1
47K LCD 2(CPTION)
[H7H7] R42 R49
R54
730
IX
-12V —HH1] J C D13 1:012
PAD C
V2-
27K i OK V2-
B 9 8 BYPASS V2- TEST
sHsH9-
J? J3 J4 A DH
W 720Tx
C6
V2-
A
cw/s- 1 sx
r1
JI R52
4.7H .CIS
OFF
| BYPASS |
I
SOLDER
PADS
ON
J2
TEST
A/
TEST
BUS
o SIL
---- rt-----
RESET
SCHEMATIC
I| RONAN
MASTER MODULE DRAWING NO. REV.
(HORIZONTAL BOARD)
MODEL X87-100B X87-1003 4
□
T2-6 +V3
0
C3
Cl
-
01
T 82PF
R3
.05
1
2N4393
c
INPUT 3 5 8
W
7
□
1K Ul,A Q2
8 MJE243 R11,15
R4
470K - C2 4 LM358N —WW- 7+—
6.8/35
C4
I
.1 1 Q3
2N4249 )—
R12
OUTPUT
-VR3 R10 4
2.2K
V
mA
o
O
+VR3 6
R6
Wy -
R8
2.45K
e-—
□
IX
GND R5 R
1 16.5K 75.0
R2
20K
ZERO
s
3
2 3
U1,B
1
IX
3
IX
2
RI
50
SPAN
-VR3
N
993 APPPoPPPPPP
+12V
R3
8
220 R15
9
27K
W5
A32
A& A0 Al A& A% 2
S B 15
6.
2
-»Fi
L_J UIF UD
A +12V
s5
IC
= C2
rh
2.2/35
RM
27K
un]
V2- *22
13
RST As U4E
-» RST
+12V
s
RS
+12V RI3
27K
%
[ As 45
3 14
BYPASS BYPASS EE
K1 U4F
Rs C18
teas
+12V
12 -» — -0S
is
5 5 475K
85
DL-O
N 3 U4A A20
g3 B UN2004 P2 A » ES
s da
6 5 27k V2- We
7 4
V2- 9 12
D
.020
44
R Q■
RL 13 12 u2B D!, 1N4148
R4
4 220K UIC
G
13
— △ TEST
V+ 10 \ LELETE
GsO:Ou
85
[
V2- C y BYPASS
V2-
( RS
1B6K
V2-
+12V
K2 v2-
9
f. 13
R12
27K
5
LHB
A BYPASS
D U3B
V+
RL I
n & —
9 12 10
X3
S
R 680< U.D
10 -% 3E M
1N4140 I n1^149
V2-
1
. 5& m
558
v2- K3
89
n
I- " ‘
NE QTX SX RX
93*
) o-
A
4
ca
Xp•
IMG
-O
Lit
Y A3e A2G Y
C30
Y
C2B
Y A26 Y
C2G Y*12 »C Cl?
20-—<
s
89—<
I
0 19
M
1 -
0 17
0
RE-FLASH
o
1
c
16
I
0 IS
n
o
0
I
K
CTA RFLAY
I
o 15
I
os
BYX
1
0s
OTX
RELAY
5. Pi ’ ------------» -HATES WITH MOTHER BOARD COECTOR.
4. P2 HAILS WITH JI ON X87-1003 P.C. BOARS
3. CAPACITOR VALUES ARE JN FARADS
2. RESISTORS ARE |/4W SX
1. ESISTORS VALLFS AnE 1N OHS
NOTTS: IB CSS OTHERWISE SPECIFIED
SCHEMATIC
I ROMAN
MASTER MODULE DRAWING NO. REV.
(VERTICAL BOARD)
MODEL X87-100B X87-1005 2
|TEST POINTS)
•• Cl C3
I
1/2 R13 IF D2
M. 1N4148
4
4
249K 249K
DP220
3 U1A
1
—W 2 2 1 IN4148
-VI
R16 .... C2 19. 6K U2 _
□ A? 14
6
n3A
4
.1
‘4 3 4 + 3.3/15
INPUT
—SRl -VI
Hi
es1
1
-VI R9
1
2
48
I------- A—
*........ AW
11. i iK
D
F
R6
G
- un
6 .05 = W.W.
o
1/2 R10
+VR1 11.I IK 7
-WW--- . SIGNAL
P220G. 9
W.W. U1B OUT
5 1000HM
5% D3
1
5 RIB +] A.
%
1N457
W1
(n 2
1/2
8 o
±C7 LM392N
1
+V1 2 +VI (9V)
R21
47K
C6_
Ti 3 U4A
5%
1/2 7
LM392N 10 GAP
6 U4B
-VRI 3 -VRI (-2.5V) 4
-VI
R19
-VRI
08
o*V3
(+25V) •1BV
No—
R62
1SK RS
Nps 1
/15
# O *VR3 1K
1
24V+ eV+ R?1
R76 5
LA 1BYPASSI
15. I/ZH L36Z-3
C2. 71.5K.1%
F2 R72 H1-ALARM
C2G
raa 11574/
4 126 Wh
FIBEN3
6.8
35 — C1?
- . —-I018
— CLH3EZ-5
29. 4K L17
LrJe7N ——
‘ R70
10 24V* 4 .1 —
K
76H18C 6.8
I _ 0
! D.9
47
S*J
REI
-Hl
*—44E
1%
a? 1115 /35 -Wr----------- 06
-H -O -YR? +122 t2v2
UH -s
*5
470 GM t-5V>
E cu 2 -V2 see
125 2B A24
24VDC
2.2 49 7HE
Let 1 _$ »012
t
1r 57 A
C24 1 125 +12V NON C * 6 NC
IX G5
2 031 r 1
LA
3 = 6,9^35 NX
F1
I0K
dlona
132
H
61V) 275 V-
1-13352-5 LATCH ‘LATO
J4 IT C24 SD
-0 -5?
t C-
u!2.6 »013
1^‘ur ,A5is12
‘-v2 1 .BK
0 +1 (Iv)
INH JS 5 14 A25 SIM
TP3
• 10
TC22 4. —273
1 [3
---------- O C-
C33 5 u,D 19 70 14
c+
D +VP1 t/2
820 1+2.5V] C32 R3 C 241+
3.3/15
-2A t 60tK< 4013R — 2,
68/35 L336Z-2.5
2B
D2E 2
S 12
L,A
1.0
LEL
+V1 +VRi 1B
=ALEDI
T2
XBTBIDT
1
C23 I 02?: C2. . Ul ,0
R21 T
V
I
CIWB1E
820 GH1
2 LB
MCA
— 1--------------------------—1. 40
4—0 SOLDER
CD407DRE TAIL
TA
(9Y)
+12V,
J: t
IX 2K
IS. —
2*
-W 1—0 Spo
1.1n IN4S7A f
+12Y2
3 2
RSI
R52
i aw
817
2 255 220K 49
PLUC-IN INUT
1 2 C8
—-0— 1
I PAD C5
SEE FAIL L IrH —W »O
CIS
AMPLIFIER
X87-1001 RTD AMP 1
5
R14
R16
US.C
x.1 R2B A
Lo RS@ " 04
21215
<20 1 A F€
0—«—— I
T
taw +IZVZ S.P.A.
X9?-1002 T/C AMP 4.7H R79 ‘ LSK
I SR T10 4 72-S C4
6.0/33 T.P. 1 20< 3 014 2
R49
1
" AIS
0—K
P3 a a + ” 19 v-2*393
2r1393
— 27F
1 le +5
D)
2N4393
2N4393 ...
C?
— 82PF
5 T2% T.P.2
R24
A
——
RA
5
013 : 33
+12V2
R39
13aay
I 5 R30 Ul,A U6.fi IMK
UJ24N 12 -5v2 24,- IX R3B
1 R34 U7.4-10
• [ ______u "
RS 9 WR51
—— C9
470K RST-C L
J
C5 « U1.E B GOK *22
CI _
6.8/391+ -V2
13, ut ,I
10
R43
C13(14001
BE *+
Cie
tu6,D
+12v2 —2A +leV2L 22tK ( 1/35
L
sac FAIL*
C 2*= =2A = 2A 1S
G +12V2 9 10
R?$A
LR exo2v
V-
R57 13
--- .S6/3s
U?,A
12,
LH
C
t€ J3
+12V 61
LLN2&
ReE ?DN, . 1%
S.P.B]. R53
M i iUlZ,G e 3
AlB
B 3 * 2CK, . 1%
R59
s bl? i
V-
8.
-O
15
ui2,C
-»HORN
Ma—
R7A : 2KK,. .* RS0:
fy.
— C4071
2*K,.1% Ul1,E LW 3 __ 9 J00K4 330K
10 LE LB,C Ria L?,B-3
2 t.
NCN© 112, D
- 2A 204 LM457A pI 5
12 —— Di LATCH
T —L LATCH
A16
p
330K
131 BCSK,1%
- ? BYPASS
-5V? -V2
“Wad IHI-ALaRn 285 " F is NC
s-s-s
T2-6 +VR3 +V3 "2* 24*+
eral -0 939
52
Cz0 SDS
F2A
R6882 130 L*HS7A
2,L.D 3
U4,B
US
RA 5 03
ZN6715
C25 re B
1 --D-
'NO4 -2-016
J 15K 1 -01
R57 K2
f
1 2a HrS.
5
Z 012:
R44
NCt
0—
N2B SI
cae so7
1 S.P.A.
P4
$ +12V2 D112 ■ 33
6
B 310.
N 0- 20 it
0 PLUG-IN 2
ISA
J U12.E L
A30 see
4
-»—O is 124*
TRANSMITTER +12V? RE INPUT 2
* .502, 1
H33
IN IOUT
- V-
ptn2,F
6.BK XB7-1004 XMIR
OUTPUT IK
S. P. BT 13
K
CD
*os6 +12 —R3?
2.7K
INPUT
SPA 3
5
2 IN E. 2 2431 — 2,—
1]‘8
12v2
=3
B 33 5 5.P.S 10
2C
JIN
LE
MU1 •
R13
4.59K,!% *6
--- -N----- »AN*+
226 1
U9,0
2
LG
C
+12VZ
L10,6
R40 ■
39k;
16
TEST
12
53 » a20
Al2
*1
U7,B ’1
1—
JC
mg)-<IH It628?‘S R12 R22
06 1 + 1 ?2 9
6
47N 40U:
8
1.7K
AB
% Q
LIN.
COD
y-
!OBK
-»
A32 V-7
C19
E.B/35
I12,G
€12 1 D 1
\ S.P, 0-#
r 7
MM
PI T 2A —
7 cis I 05 01 L3
-VR3
S.P.B.O-S H D2 1 = 28
95.3K.
A COGEMTS MCNTED ON PLUC-IN HEADCR, Pl. I 95.3 95 . "
IX IX IX * 95. 3K 4.B7K
IX
3. CAPACITOR VIES AF£ IN FARALS.
2. RSISTOR AE 1/4W, S%
I
1. RESISTOR VALUES AE IN GM. I -5v2
I -5V2 a
Il RONAN
LPTICN
NOTES: ULESS onuoIS SFECIFIEO
SCHEMATIC
VIBRATION MONITOR
SINGLE AND DUAL SETPOINT DRAWING NO. REV.
X87-1016 0
R2
—
10K
C3
HF
.01
RI
U2A
R17
LF442CN 3.9K
J1
0*
TEST POINTS
4.
< 6 BLK 4---- 1
1
N7 Cll
N4
A
I—
42.♦VI
C13
A
LF442CN
1/50
LF442CN LF442CN
N2 N3 8 N6 1
r SIG.CS -H
A.
-
A
X
U2B 7
N5
A At NB
t
U5A
R21
/
R23
A±2 10
5
USB
X C
INPUT N1
L 41 -vi A
H2l
R24
A
R22
A
D44.
1N5287 -C12
+2.5V — 1/50
CD -VI -VI
RIO R19
C1 +V1
R14
A +V1 20K, IX
♦VI 2 0+14.5V A All
2_
LH392N -cg
3.3/15
2 • D3 D2
+VR11 2.5V
R15 -2.5V A U1A R20
LF411CN
IN457A
1N457A
SOK. IX
100K U4
5
Rie
+2.5V 85.4K. IX
0-14.5V 62FR10K
ZERO
R13 A R5
J2
i A
-2.5V X
U1B 2
5.8M
—10
SENSOR OK
R8
90.5K. IX
Iyr
R7
BsH2oK
CB /so
GAIN
LH392N
R3
x1e C8 1/50
R4
— ZERO
nareron VALUES AM IN os
CAPACITOR VALUES AM IN MICROFARADS
LF411CN T9s
-V1
NOT** ant ess onmntse SPECIFIED)
I|| RONAN
VIBRATION
INPUT BOARD DRAWING NO. REV.
X87-1017 1
+7 SV
.SV
S’ak
C2 SPAN
518 +7 SV
.001
IF RE 3
VR1 +2.5
AS
A +7. SV
A 3.3K
st
SV 04
aLLM336
U2A C040138E Qi 2
T12 >50 z-2.5V
UiB 7
4
Hi
R14 C4 A VNO106N3Malo
D
R17
5,
41— 1 RE 2
& 71 = 5.6K LM393N
[
INFUT
27K . 47
02 R15 Cl
W2
2
U1A
LM393N
CLK
Ds0
LF442N
W4
L. 1N457A
330K
330
pf W3
-14.4V
$5s0
VA1
R9
VA1
[5 U2B
1 28oK.
R2
1%
+VR1
24.3K, 1% C9
IP
(
+VR1 {+2.5V)
52PA10K
SENS.
R4
301,
ADJ.
1X
I C040138E
Re
BSPH100K
ZERO
3
1
RIO
499K, IX
All
A
A20
/ A
A21
6
U3B 7
R15
47
OUTPUT
R13
axo 1
VSS (U2) C7,
I
820
+7.5V
I 1
0i
a L LM336Z-5 . OV
51/,
14. SV
R4
-14.5V
1
R3 R25 >>2 OUTPUT
24 9K
R7 CR6Y ACR5
13IC? 14 CR4 R39
R8
-VW
12 BLM324N c122 R24
10.0K
R42
47K
5%
R9 R27 R36, 10 OK
24.9K +12V
R10 CR9Y ACRB
3 J3
8 CR7 R26
her —M- W Oi o- 2 7
6
R11 10IC CR23 (C4
M324N —P J4 3 J
4 714HC
R12 R29 Q
24.9K -12 V
R4 CR12Y ACR11
6 J5
VW
R5
IC 1 7
0,
CR10
—M—
R28 +O o-
M324N CR24
—p J6
R6
R30 oo + 12V + 12V
6.8/35 +I2V
R17
Car
Co .
CR13 A
24.9K
3 8
ft
(n 4 J7 R44.
cn VW CR14 R3I 1
-M- VWy Oo iC3
R18 2
J8 LM393N
— 324NN C4
pO-6.8 o o-
R19 R32 R41
+ 12V 5 << R45. »1 LIN. CODE
24.9K 806' 10K,5%
R13 13 CRts;: J9 5
VW CR16
lie: 14 R33 7
— H--- 0o
1
R14 12 1 B 6A
-12V 3 << M324N J10 R43 4 LM393N
R34 oo
-12 V
4
2A9K R40
Rt5 -C5
9 CR17 l i J11 2.2M 1/35
6 CR18
—H
R35
- +
—o <
5%
R16 10 CLM324N
J12
R36 To < O-
24.9K
R20 6 CR19A
he; 7 CREO R37
——
R21 5DLM324N
ar
IC!
ICL7I07
CPL
osc
TEST
38
37
Ci l
1-IOOpf,D.M. I RI
27
1/2 w
1 7
CR3
IN 4148
IN 78M05 OUT
(
+5V
91 [
QI VRI
36 R/2
Al REF + $ 1.5K 4410
2N4410 CR6
COM J. CIO
35
O
FI REF W RI/ . - C7 J
C2 "“22/25
34 CI2
2.74K, CR7 .001 1F <
61 C REF -F
.1
1%
J____ LM336Z
-2.5 1 2 8
E! CREF
33
32
2
RI3
500
R2
180
R3
CR4
I
D2 COM 1
33K
— C8 A ? CR2
R5,100K 02 1 63/35 IN752A
31 RIO CR5
C2 IN+ 2N4410
*
B2 IN—
30 J C5
2.OK
. J%
3
4
'9
4 R4
330
29
16,
“A
A2 AZ
O 5
R7
IQ
BUFF 28
F2 6
1%
E2 INT 27
44 R6
27
TI
X83B6
V- 26
D3
+5V
25
%
B3 G2 +5V
C3 RI5
24 — 6.8/35 IOOK
Ea
F3 03
3 7
NJ
>14
23 1 IC2 °C
3
E3 A3
1
A 6 + 5V
R.7
A,64 G3 22 IOOK (2— RI4
4)0]- "F" POST CONNECTIONS TO DISPLAY BOAF
3) CAPACITORS ARE IN MICROFARADS.
IOK 21 RESISTOR VALUES ARE IN OHMS
21 R16
9
C4 GND 5
1 IOOK
2 IC2
34
>13
v
I > RESISTORS ARE I/4W . 5%
NOTES : UNLESS OTHERWISE SPECIFIED.
+ 11
a [888 ajn =
13 IC2
D 10
14
19
1C2|
C8
LM339N
II ROMAN
SCHEMATIC
DIGITAL PANEL METER DRAWING NO. REV.
MODEL X87-101
X83-1005 2
"5
+5V
323 24 t ff 4
DP
A,B,4 C,4 E3 F3 A3 B3 63 C3 D3 E2 F2 A2 B2 G2 CZ D2 El Fl Al B. Gi Cl DI
22 16 15 2 00
00
?
IN4I48
JN4148
CR2
CRI
300
RI
JN4I40
IP
o zr
o £P
o
6-rdO
RPI,E
8o
6-£dC
6-ZdG
330
1 C,D 14 I 4 t A 4 LL A 14 A 14
2F 8 13 2 F B 13 2 F 6 13 2 F B 13
CJI
co 3 C,D 3 .3
DP4
A Ji
DP3 G I. DP2
G It
DPI
G 11 RPI,D DPO G If
B 10. C 10 c 0 C IO 330 C I0.
6 9 6 9 6 6 9 6 9
7 C 8 7 E D 8 7 E D 8 7 E 0 8 .7 E D 8
RPI,C
__ 330
JI J2 J3
CM
81
m
SCHEMATIC
[| ROWAN
DIGITAL PANEL METER DRAWING NO. REV.
DISPLAY BOARD
MODEL X87-101 X83-1006 1
5
+12V << O +12V
3
-12V << -O -12V
+12V
4
GND<<
1 R3
A Ul
LM339N
RIO
12.45K
+
.12 H.H. 6
11 —AWW— > IN
RI 13 D Q1
I
10K A 2N4393
LIN
CODE
< W 10 01 S 2
IN4148 RH
1OOK OUT
R2 - 01
2.2M - 1/35
1 R4>
806 <
12 1
Q2
9 2N4392
S R12
14
B - 562K.1%
8 - —NW—
I
03 D
(n 1N4148 R14
<o 100K R13 RIS
II-BK 8.45K
jA
>R5
RS
12 1%
12V
04 02 -12V
+12V 1N4148 1N4148
+12V
R6 R7 + 12V
100K 130K
RS +CZ
V] 10
1% %—» VIB
8
"F < G
c 1
1OOK
4
3 6.8/35 RIS
10K
RIG W2 9
7 2 15K "o—EU
0 2N6715
r
R8
. RE
2.2K R17<
12 4.7K>
-12V
SCHEMATIC
I( RONAN
ENGINEERING UNITS REV.
LINEARIZER DRAWING NO.
MODEL X83-200-EU 2
X83-1031
Instructions
and
Operating Manual
SERIES X87
HIGH-DENSITY PROCESS
MONITORING SYSTEM
Errata Sheet
Revision March 1, 1990
|ROMAN
A0r-lubb
(MASTER MODULE) 11.005
6.25B DIR
6.35MM 281559HM
88338
■
338
338
338
318
[DJa"IMC
0> • 0
[DJOIME
36
Iff
I1
BBON watS xa7
orr
0so
DJdME
?n
HUM
©.
wAznERSnEKAGISEGAGKSNRzEASIzEsIzREziah
sail
Miimoi
C ) 210
n.
2.250 .54 Ml
57. ism
G 000-
€-
O.
(DG0G0688381©
D
1,404
37.70M1 |
] 1,5.12 -
B.74M 465. ) 3MM sea. 565m
(60-06888819
- 19.0E0 - 1
482.60 1
(C0C08181
12121921221731731777737/32/ s
RHKRLHKHHRLFRTRHHHSH a
(GC85cis
sa 68)83816
©
a
o
1 [O
99192292742/79212«
7 iininiiDiii
a
l aammoanu •
O
4«*FPX;EE=M==*-M-
IMMHH
0W
01uu
......... $
g
1 g (nr0101011/0/0101010.
$- 6
Q gimunre l arure I
IIRONAN
d
JI HONAN
OUTLINE DRAWING
X87PR-20 DRAWING NO. REV.
X87D1 3
r1 th 8 = h i h B B B
:)
HHWII0
Bl
0 19 19 19 19
0 10
R-FLASH OR
a is 18 19 C 19 SETPOINT C
RELAY B
0 17 17 12
o
17
_Eo
njrallullalniin
CTA B re
RELAY o 15 15 15
I 14 14
OR
13 13 13 13 SETPOINT T
HORN — 12 12 12
ru
12
N
RELAY "T OR
l□|lllo|llolll|a|lllQlllla
+20 TO 30VDC
HFuJHMuaP
0
2 10 to 10 10 (REF TO V-) A ME
ag 9 9 TRANSMITTER
RESET
m
-O 8 6 OUTPUT
w
SILENCE S.P.B
O 7 2
"TESTo’o E 6 |o 8 O
B ISil WHJ
5 S 5 5 INPUT
S.D.
-O o
BYPASS
RET. JUNCTION
8
RESISTOR LOOP
a 3 3 3 ESISTH? 3 a
V-
ANALOG 2 2 2 a 2
2
19
OUTPUT
0. SURFACE ftOUWT
Ul RUXILIRRY
RASTER MODULE tore 3) THERMOCOUPLE RTD INPUT n, V INPUT nA INPUT REMOTE SELECT OUTPUT TERMINAL STRIP
• TO ENABLE TEST FUNCTION INPUT (FOR 2-WIRE RTD (TERMINALS 2 OF DISPLAY (COMMON TO ALL (1 THROUGH 10 ARE
ONY NEN BYPASS IS ACTIVE JUMPER BETWEEN AND 3 CONNECTED INPUT MODULES) SYSTEM BUSSES)
CONNECT TEST SW TO TERI INAL 9
TERMINALS 2 B. 3) TOGETHER INTERNALLY) SETPOINT B
IS OPTIONAL
0 19
0d 17
0l0 16
15
13
12
11 NOTES : UNLESS OTHERWISE SPECIFIED
1. 24VDC POWER IS CONNECTED TO POSITIONS 1 & 2
10
LABELED 24V*+* AND APPLIES ONLY TO '
□| 9 RACK AN PANL MOI HT.
2. CONNECT AN IB GA JLPER BETWEEN TERMINALS
LABELED ’W AT AUXILIARY TERMINAL STRIP.
IF TWO CR MORE CHASSIS ARE INTERCONNECTED VIA
6 AUXILIARY TERMINAL STRIPS, INSTALL ‘W’ TO
5 'W AMPER ONLY ON CHASSIS WITH MASTER MODULE
3. THE MASTER MDLLE OCOLPIES FIVE POSITtOS.
CONNECTIONS Nt MAH TO TE LEFT TERM. STRIP IN
1--- G A SET OF TEF1. STRIPS. I.E. POSITION 1 IS USCD
11SVAC N 2 IF THE MASTER MODULE IS IN PCS. 1-5.
—H 4. IF SHIELD GROUNDED AT TRANSDUCER.
DO NOT MAKE CONNECTION AT MONITOR END I| RONAN
POWER INPUT CONNECTIONS X87 SM
FOR XB7-115-50 POWER SUPPLY
TERMINAL ARRANGEMENTS DRAWING NO. REV.
X87D82 8
0|00Oo]OTOOOJOIIOOIDIOOIIIOI
19 19
u to
10 IB
1? 17
to u.
15 15
14 14
13 13
[r
12 12
11 11
10 10
F
9 9
co to
8 8
7 7
M98 6
6
un 0
5 5
SHLD SHLD
Q
0
_J
4
3 3
€
.2
N to
uh
COM CHARGE 2
S200 SERIES 2
AMPLIFIER
(n
Lp
(
CD
01
0
un
ui
KTICHTeII
Cd
u
ru
ru
TT
to E
S
C
□
t
03
161000 ©0016Q
VELOCITY
PROBE TRANSDUCER
tn
9200 SERIES
U1
U
2
-24VDC -24VDC
UillOiiIiA
•l
t
T r j
MEOJ,M606,M660 SIG BENTLY NEVADA t SIG
X87 SM TERMINAL 01 RONAN
ARRANGEMENTS DRAWING NO. REV.
DISPLACEMENT VELOCITY TO VIBRATION INPUTS
INPUTS DISPLRCENENT
CONVERTER ' X87D82 8
8813810
1 1.750
29E.41 MM
- . £16 DIA NNFIN HOLE
5.54 Mi
18816
ole
33510
8le
690 1O
mt
0 20
OJa] HAII©
sl
®l
1.3
-o
111T
EEONAE ECRIES xe7 o -0
es0
111
—0
=%-G-o
GSi
11
me
1I
8 [ ) Di © 5.220
132.59 I
-0- i
-o
MAMEWAKTMTTZTM
El S @0-
(DC0C08833819
s
i
=
i
2
I
=WWMM".2PI"TFA
- =============
=asanraanapprz.e
■ H.NA.NRMARRRN.AAAM
6.500
155. I I
= ffiW.WJtMg.WJ.fJW.PM
RNNN
Bonpohnner
1182
A/AMAEAnAhAnAnhA
(CDC68:1619
=57272:727721.7.12."
10.860
•EMTYYYNYYT
270.76 1*1
zmm====
=======
(£60606889819
-soMMAY
-WMTYYTMEY
- ERWRMSR
-mroAer
-*-*** ==s ssausm$
---------r-pv-ppst- .
@@G8:lis
-mRSNSH:
EES g) 3381e
(
=1***=
sOE
at"
4
2.000
52.69 H
o® ©
t
11
$
l
.25B — B
£,35 *1
I
DIM A DIM B
T X87-115-50 DA
MODEL N. X8?-47 1.472,473 (POWER SUPPLY)
IN 11 IN M1 (VIBRATION MODULO x87-B
(BLANK PANEL)
XB7520 19.375 432. 12 16.875 479.42
XB?-430 X8?-300
<DUAL SETPOINT (SINGLE STPOIN1
X87SH13 13.340 336 - 64 12.840 325.14 MONITOR MODULE) MONITOR MODULE)
M 338io Daa[ME
0. 0
91
I if1:1 0
IMS
fl
3
•|l 336ieDiaMC
BIU
DOME
DOME
SCRIES 107
OSOHME OdME
tJ mrmmeri mie
(
a6 sa ire
MID]
MID]
-o
000 O- Ha
ca
HI
U 0 1 mememisinooio
0 -UtooJol
©•
HBHM 8361®
•aas 2310
0 O
6
660N
valp
1 'Aii
l
i
I
§
3
□ 3 060T
ssOl
00000
-O0-0
000
11129
—%
000
0 -0
1 199
11
11
—0 -0
Ml
©©
§8
Ot
in
8:
•orne
□
H
(-
7
[
t
_
lk
[Tthromagognnqnoungoprmoppngngc
is i
q4
O C (CUTOUT)
meo=umEaur!)=
C—
GJ
m.
------------ R
a
T
3S
un
I
I
Ml
C
LJ
C
T"EF59M9—qrnain —
a (uSRkuxzuxausunassdnntssdsnuarn
~======.
• ====2==**=**
WTTWIATRH12F21219212T9—D1227=
i Ezszmucns=
BMtoictcioronraicmotordcliciolh
aietaretetdintaldigtelelggig-y"Hdne."
tlstolbtolololmulbtuld.ordulotululo
TH 1.1
si**a***252***-
CARD RACK
. ..............
LTAIL E
o
SITIE Ym7
4
d
8
otuzukrhtrzrnuinozrhnziz
- dkznznzutkzrntnzndzihf
IN
Ll5imEimiE!EI!IMM3
IN H MM TN m IN M
guu1p1gxerer2191:12+9Aqn1-m12."II‘
OUTLINE DRAWING
I( RONAN
"12naan
o
o
P115 X>7
X87PM
i
In
+20 TO 3BVDC 9
1.0 mV/DIGIT 2 LOOP 2 (REF TO V-] 2 2
2
RESISTOR
88888008
3 3 3 3 3
RET JUNCTION
S.D. RESISTOR
drgu00
BYPASS INUT
Q
O CP 5 5 5 D 5
ndodldidoggoogoon
* TEST 5.P.A E
G C
sTo10001SI
6 O 6
SILENCE 5.P.B
Il IMIMIMIMIMIMIM IM IC-IIL-IIE-IIL-BC-IIt-JII-L-lIIeII-]
7
-O O
R.SET B 8 8
/ODO
8 TRANSMITTER
9 9 C 9 OUTPUT 9
10 D 10 AM
G
10
t
MORN X CR 11
t2 SETPOINT L '12
ry m
12 12
jgglgggJiD
RELAY
13
tr
13 13
OR
!
14
CTA X 0215 15
th
15 15 B ME
RELAY
IE IS olois 16
O
OR
521 SETPOINT 17
2 to a 5
17 17
RE-FLASH _L 18 16
B [8
RELAY OR
19 19 15 19
-
INPUT
(NOTE 3) (FOR 2-WIRE RTD (TERMINALS 2 OF DISPLAY (TYPICAL TO ALL
* TO ENABLE TEST FUNCTICN JUMPER BETWEEN AND 3 CONNECTED INFLIT MODULES)
ONLY WHEN BYPASS IS ACTIVE TERMINALS 2 & 3) TOGETHER INTERNALLY) SETPOINT B
CON ECT TEST SW TO TER1INL 9.
OTHRHISE CONNECT TO V-. IS OPTIONAL
HIIIU
CCECT INUT de:
O)
TO POS “A" PER
al 2 2
D
INUT I FORMATION
H/+ 3 3
POWER INPUT N/- 2
(SEE CHART)
nilludru
G NOTE; 1. 24VDC POWER IS CONNECTED TO POSIT 106 2) 5
OF TERMINAL STRIP POSITIONS I A 2
6 6
ngm
230VAC H N 9
3. THE MASTER MODULE OCCUPIES FIVE POSITIONS. 11
10 OR OR
000
[■HIliJHU
13 13
12 USED IF THE MASTER MODULE IS IN POSITIONS 1-5.
4. IF SHIELD GROUNDED AT TRANSDUCER ,
OR
1___
13
DO NOT MAKE CONNECTION AT MONITOR END. 0M 15 D ME 15
16 16
15
SETPOINT C
OR
17 SETPOINT U
OR E 17
16 B D
18 19
18
L OR
19 LEo 13
R B
19 OUTPUT X07-800 J
H98
98
.oro
)
8
lie il |0 10 HO 0 O0HO TDD
S’
M5,hurl M99,M99-1,M86
in a
CHARGE
19,
58
umwww
w ru
ru
ry
H600,H606,M860 BENTLY NEVADA
Y
£
8
£
C
U
rsiifliigr&iisiswiMsiisiisB
o to 4 • a —
mmu
E
oesee*dsesumm«*UN
C.
1 GESEK"SNEE0mwt—s
I| RONAN
X87 RM, PM TERMINAL
ARRANGEMENTS DRAWING NO. REV.
VIBRATION INPUTS
X87D36 10
RONAN
RONAN ENGINEERING RONAN ENGINEERING
5 RONAN ENGINEERING RONAN ENGINEERING
COMPANY LTD. U.K. LIMITED (AUST.) PTY. LTD.
P.O. Box 1275 1 Tilley Road 32 Bermondsey Road Unit 10. 8 Leighton Place
21200 Oxnard Street Crowther District 3 Toronto, Ontario Hornsby, N.S.W. 2077
Woodland Hills, Washington, Tyne and Wear Canada M4B1Z5 Australia
California 91367 U.S.A. United Kingdom, NE38-OEA (416) 752-0310 • Telex 63662 (02) 477-7344 • Telex 73467
(818) 883-5211 • Telex 698-490 (091) 416-1689 • Telex 537-746 FAX (416) 752-8072 FAX (02) 477-6151
FAX (818) 992-6435 FAX (091) 416-5856