Professional Documents
Culture Documents
Falk Right-Angle-Gear-Drives - Parts-Manual
Falk Right-Angle-Gear-Drives - Parts-Manual
NOTE: Drawings are representative of this series of drives and may not agree in
exact detail with each drive size. When ordering spare parts, give complete
nameplate data: Model, M.O., HP, RPM, Date and Ratio with part Reference No.
and Description as stated herein.
1AB Bevel Pinion Shaft Assembly t TABLE 2 — Bevel Pinion Shaft Assembly
Parts List
Reference No.& Reduction
Part Description
Double Triple
1AB2-50 1AB3-50 Bearing (2), H.S. Shaft
1AB2-51 1AB3-51 Bearing (2), H.S. Shaft
1AB2-52 1AB3-52 Gear, Bevel Pinion & Bevel
1AB2-53 1AB3-53 Furnished as a set only.
1A82-54 1AB3-54 Shaft, H.S.
1AB2-55 1AB3-55 Nut, Lock (Pinion or Bearing)
1AB2-56 1AB3-56 Key, Bevel Pinion Q
1AB2-57 1AB3-57 Key, H.S. Extension
1AB2-58 1AB3-58 Spacer, Inner Bearing Q
1AB2-59 1AB3-59 Spacer Q
1AB2-61 1AB3-61 Seal Cage Assembly — See Ref. 30
on Page 1 and Below
1AB2-62 1AB3-62 Stinger, Oil (See Note)
1AB2-63 1AB3-63 Spacer, Outer Bearing Q
1AB2-64 1AB3-64 Key, Oil Stinger or Pump Gear
NOTE: Bevel gearing is case hardened after cutting, and 1AB2-65 1AB3-65 Gears, Pump
subsequently lapped in matched and marked sets to ensure 1AB2-66 1AB3-66 Pump Assembly (See Note)
proper tooth contact. Unless bevel pinions and gears are 1AB2-67 1AB3-67 Nut, Hex Lock
installed as matched sets, in accordance with the instructions 1AB2-68 1AB3-68 Hub, Bevel Gear Q
in Rexnord service manuals, Rexnord cannot be responsible for Also order Shim-Gasket Kit (Ref. No. 100) listed on Page 1.
the rating, life, noise or performance of the parts or the Q Used for some sizes and ratios.
products receiving them.
Pinions are solid on shaft for some ratios.
Drives are furnished with either oil pump or oil slinger,
depending upon size and ratio.
Figure 1 Figure 2
t Shaft assemblies can be furnished assembled if requested. However, for periods of extended storage, this is not recommended; parts, especially bearings, ore more
effectively protected against rust in their original packages.
t Shaft assemblies can be furnished assembled if requested. However, for periods of extended storage, this is not recommended; parts, especially bearings, ore more
effectively protected against rust in their original packages.
TABLE 6 — 5A Low Speed Shaft Assembly NOTE: Drawings are representative of this series of drives and
Parts List may not agree in exact detail with each drive size. When
ordering spare parts, give complete nameplate data: Model,
Ref. No. Part Description
M.O., HP, RPM, Date and Ratio with part Reference No. and
5A1 Bearing, L.S. Shaft Description as stated herein.
5A2 Bearing, L.S. Shaft
5A3 ‡ Gear, L.S.
5A4 ‡ Shaft, L.S.
5A5 Key, L.S. Shaft Extension
5A7 Spacer, L.S. Gear
5A9 Key, L.S. Gear
5A10 Umbrella
5A11 Seal Ring
5A12 Sleeve, Wear — L.S. Seal Q
Also order Shim-Gasket Kit (Ref. No. 100) listed on Page 1.
‡ Some low speed gears are finished (turned and cut) while assembled to their
shafts. Where circumstances permit, check with Factory to determine if the
gear ONLY can be supplied.
Q Used for Sizes 2070 & 2080 only.
t Shaft assemblies can be furnished assembled if requested. However, for periods of extended storage, this is not recommended; parts, especially bearings, ore more
effectively protected against rust in their original packages.