Professional Documents
Culture Documents
sl26 3
sl26 3
SL-26/30N
WARNING
All personnel shall carefully read, understand and follow all safety rules,
operating instructions and the Scaffold Industry Associations MANUAL OF
RESPONSIBILITIES (ANSI A92.6) before operating or performing maintenance on
any UpRight aerial work platform.
SAFETY RULES
NEVER operate the machine NEVER elevate the platform or NEVER sit, stand or climb on
within ten feet of power lines. drive the machine while el- guardrail or midrail.
THIS MACHINE IS NOT IN- evated unless the machine is
SULATED. on a firm level surface.
NEVER operate the machine without first surveying the work area for surface hazards such as
holes, drop-offs, bumps and debris before operating machine.
NEVER operate the machine if all guardrails are not properly in place and secured with all
fasteners properly torqued.
SECURE gate across entrance after mounting platform.
NEVER use ladders or scaffolding on the platform.
NEVER attach overhanging loads or increase platform size.
LOOK up, down and around for overhead obstructions and electrical conductors.
CHECK all four tires for correct inflation. See Specifications.
DISTRIBUTE all loads evenly on the platform. See the back cover for maximum platform load.
NEVER use damaged equipment. (Contact UpRight for instructions, see toll free number on back cover.)
NEVER change operating or safety systems.
INSPECT the machine thoroughly for cracked welds, loose hardware, hydraulic leaks, damaged
control cable, loose wire connections and wheel bolts.
NEVER climb down elevating assembly with the platform elevated.
NEVER perform service on machine while platform is elevated without blocking elevating assembly.
NEVER recharge batteries near sparks or open flame; batteries that are being charged emit
highly explosive hydrogen gas.
AFTER USE secure the work platform against unauthorized use by turning key switch off and
removing key.
NEVER replace any component or part with anything other than original UpRight replacement
parts without the manufacturers consent.
California Proposition 65 Warning
Gasoline and diesel engine exhaust and some of their constituents are known to the
1 defects,
State of California to cause cancer, birth and other reproductive harm.
Downloaded from www.Manualslib.com manuals search engine
Introduction Electric Model inspection
1. Verify batteries are charged (see Battery
This manual covers SL-26/30 Narrow Work Plat- Maintenance, page 6).
forms. This manual must be stored on the 2. Check that A.C. extension cord has been
machine at all times. disconnected from charger.
Pre-Operation and Safety System Function Inspection
Inspection
Read, understand and follow all safety rules
and operating instructions and then perform STAND CLEAR of the work platform while
the following steps each day before use. performing the following checks.
1. Remove module covers and inspect for dam- Before operating the work platform survey
age, oil leaks or missing parts. the work area for surface hazards such as
2. Check the level of the hydraulic oil with the holes, drop-offs, bumps and debris.
platform fully lowered. Oil should be visible in Check in ALL directions, including above
the sight gauge. Add hydraulic oil, if necessary the work platform, for obstructions and
(see Specifications, back cover). electrical conductors.
3. Check that the fluid level in the batteries is Protect control console cable from possible
correct (see Battery Maintenance, page 6). damage while performing checks.
4. Carefully inspect the entire work platform for
damage such as cracked welds or structural 1. Unhook Controller from front guardrail. Firmly
members, loose or missing parts, oil leaks, grasp Controller hanger in such a manner that
damaged cables or hoses, loose connections the Interlock Lever can be depressed, while
and tire damage. performing the following checks from the
5. Check that all guardrails are securely in place ground.
with all fasteners properly torqued. 2. Pull Controller Emergency Stop Button out to
6. Check tire pressure (50 psi). ON position.
7. Place the Chassis Emergency Stop Switch to 3. Turn Controller Key Switch clockwise to ON.
the ON position. Turn fully clockwise to start engine (Gasoline /
Propane engine only).
Gas / Propane Model Inspection Note: If the engine is cold, depress the choke
1. Check fuel supply. button and hold while starting. Diesel mod-
2. Check engine oil level with dipstick. els: depress and hold the glow plug button
3. If equipped, check coolant level in radiator. for 6 seconds prior to starting to engage the
DO NOT check coolant when radiator or glow plugs.
engine is hot. 4. Turn Drive/Lift Switch to DRIVE position.
4. Set gasoline / propane selector to desired
position. Set to the center position to purge the
system when switching fuels. If the machine is
to be operated on propane, open the supply Chassis
valve on the tank. Hydraulic Tank Emergency
Sight Gauge Stop Switch
NOTE: When using LP gas, use clean, water free
liquid petroleum gas, preferably from a bulk
storage tank. Follow the instructions located on
the Power Module tray for filling the tank.
Emergency
If you smell propane, close the supply Lowering Valve
valve on the tank immediately until you Chassis Lift Fuel Selector Switch
have located and corrected the leak. Switch (Propane Option Only)
2
Downloaded from www.Manualslib.com manuals search engine
5. With the Speed Range Switch first in HIGH
TORQUE and then in HIGH SPEED actuate Operation
the Interlock Lever and slowly push the Control
Lever to FORWARD then REVERSE positions Before operating work platform, ensure that the
to check for speed and directional control. The pre-operation and safety inspection has been
farther you push or pull the Control Lever from completed, any deficiencies have been corrected
center the faster the machine will travel. and the operator has been thoroughly trained on
this machine.
6. Push Steering Switch RIGHT then LEFT to
check for steering control. Travel With Platform Lowered
7. Rehook Controller on front guardrail. 1. Verify Chassis Emergency Stop Switch is in
8. Push Chassis Lift Switch to UP position and the ON position.
elevate platform while pushing the Tilt Sensor 2. After mounting platform close and latch gate.
off of level. The platform should only elevate Check that guardrails are in position and
about one foot (.3 m) and the Tilt Alarm should properly assembled with fasteners properly
sound. If the platform continues to elevate and/ torqued.
or there is no alarm STOP and remove the 3. Check that route is clear of persons, obstruc-
machine from service until it is repaired. tions, holes and drop-offs and is capable of
9. Release the Tilt Sensor and fully elevate supporting the wheel loads.
platform. 4. Check clearances above, below and to the
10. Visually inspect the elevating assembly, lift sides of the platform.
cylinder, cables and hoses for damage or 5. Pull Controller Emergency Stop Button out to
erratic operation. Check for missing or loose ON position.
parts.
6. Set the Drive/Lift Switch to the DRIVE position
11. Lower the platform partially by pushing Chas- and turn the Key Switch to ON. On Gasoline /
sis Lift Switch to DOWN, and check operation Propane models, start the engine.
of the audible lowering alarm.
Note: If the engine is cold, depress the choke
12. Open the Chassis Emergency Lowering Valve,
button and hold while starting. Diesel models:
push in and turn counterclockwise, to check for
depress and hold the glow plug button for 6 sec-
proper operation. Once the platform is fully
onds prior to starting to engage the glow plugs.
lowered, close the valve, push in and turn
clockwise until the detent engages. 7. Set the Drive/Lift Speed Range Switch to HIGH
13. Close and secure module covers. TORQUE.
14. Turn the Controller Key Switch counterclock- 8. Grasp the Control Lever so the Interlock Lever
wise to OFF. is depressed (releasing the Interlock Lever
cuts power to Controller). Slowly push or pull
the Control Lever to FORWARD or REVERSE
Interlock Steering to travel in the desired direction. The farther
Lever Switch
you push or pull the Control Lever from center
the faster the machine will travel.
Speed Range Control Lever
9. While moving, push the Drive/Lift Speed
Switch Range Switch to HIGH SPEED for travel on
Drive/Lift
Switch level surfaces or to HIGH TORQUE for climb-
ing grades or traveling in confined areas.
Steering
1. Push the Steering Switch RIGHT or LEFT to
turn the wheels. Observe the tires while ma-
neuvering to insure proper direction.
NOTE: Steering is not self-centering. Wheels
Emergency must be returned to the straight ahead position
Stop Switch by operating the Steering Switch.
Glow Plug /
Choke Button
Key Switch (Kubota Only)
Figure 2: Controller
3
Downloaded from www.Manualslib.com manuals search engine
Raising and Lowering The Platform After Use Each Day
1. Position the Drive/Lift Switch to LIFT. 1. Ensure that the platform is fully lowered.
2. While holding the Control Lever so the Inter- 2. Park the machine on level ground, preferably
lock Lever is depressed, push the Control under cover, secure against vandals, children
Lever slowly to UP to raise the platform. Push- or unauthorized operation.
ing the Control Lever farther increases the lift 3. Turn the Key Switch to OFF and remove the
speed. key to prevent unauthorized operation.
3. When the work task is completed, position the
Drive/Lift Switch to LIFT and lower the platform Parking Brake Release (Figure 3)
by pulling back on the Control Lever until the Perform the following only when the machine will
platform is fully lowered. not operate under its own power and it is neces-
sary to move the machine or when towing the
Travel With Work Platform Elevated machine up a grade or winching onto a trailer to
Travel with platform elevated ONLY on firm and transport.
level surfaces.
1. Close the needle valve by turning the knob
NOTE: The Work Platform will travel at reduced clockwise.
speed when in the elevated position. 2. Pump the Brake Release Pump until the Parking
1. Check that the route is clear of persons, Brake Cylinder Rod clears the wheel rotor.
obstructions, holes and drop-offs and is ca- 3. The machine will now roll when pushed or pulled.
pable of supporting the wheel loads. 4. Be sure to open the needle valve and verify
2. Check clearances above, below and to the that the cylinder rod has extended before the
sides of platform. machine is operated.
3. Position the Drive/Lift Switch to the DRIVE
position.
4. Push the Control Lever to FORWARD or
REVERSE for the desired direction of travel. Never operate work platform with the
Parking Brake inoperative. Serious injury or
Emergency Lowering damage could result.
The Emergency Lowering Valve is located on Never tow faster than 1 ft./sec. (.3 m/sec).
the left hand side of the chassis through the
cutout in the Control Module cover.
1. Open the Emergency Lowering Valve by
pushing in and turning the knob counterclock-
wise approximately ¼ turn, the knob will pop
out disengaging detent.
2. Once the platform is fully lowered, be certain
that the Emergency Lowering Valve is closed
Pump
again. The platform will not elevate if the
Emergency Lowering Valve has not been
closed.
3. To close the Emergency Lowering Valve, push
the knob in and turn approximately ¼ turn
clockwise until the detent engages.
Switching Fuels (Gas / Propane Only) Needle Valve
1. With engine running push the Fuel Selector
Switch to the center position.
2. After the engine has quit running select the
appropriate fuel supply.
3. Restart the engine.
4
Downloaded from www.Manualslib.com manuals search engine
Fold Down Guardrails Transporting Work Platform
This procedure is only for passing through door- By Forklift
ways. Guardrails must be returned to proper
position before using the machine. NOTE: Forklifting is for transporting only.
Fold Down Procedure (Figure 4)
Note: When performing the following proce-
dures retain all fasteners. See specifications for weight of work plat-
1. Place controller on platform. form and be certain that forklift is of
2. Starting at the front of the platform, remove adequate capacity to lift platform.
nuts, bolts and washers from the top of the
front guardrail. Fold the front guardrail down Forklift from side of Chassis by lifting under the
onto the platform. Chassis Modules (Figure 5).
3. Close and latch the gate. By Crane
4. Remove nuts, bolts and washers from the top 1. Secure straps to Lifting Lugs only (Figure 5).
of the rear guardrail. Fold the rear guardrail
down onto the platform being careful to keep By Truck
gate latched at all times. 1. Maneuver the work platform into transport
5. Remove nuts, bolts and washers from the top position and chock wheels.
of the side guardrails and from the slideout 2. Secure the work platform to the transport
deck midrail. Lift up and fold one side guardrail vehicle with chains or straps of adequate load
in so it rests on the deck. Repeat with other capacity attached to the chassis tie down lugs
side guardrails. (Figure 5).
Erection Procedure
1. Raise side guardrails making sure each is
pushed down to secure the guardrail in the Tie down lugs are not to be used to lift
vertical position. work platform.
2. Install bolts, washers and nuts between the Overtightening of chains or straps through
side guardrails, tighten securely. tie down lugs may result in damage to work
3. Raise rear guardrail assembly, aligning holes platform.
and install bolts, washers and nuts. Tighten
securely.
Front Tie
Downs/
Lifting Lugs
Rear Lifting
Lug
(Typical)
Forklift
Rear Tie
Downs
Figure 4: Fold Down Guardrails Figure 5: Transporting Work Platform
5
Downloaded from www.Manualslib.com manuals search engine
Maintenance
DO NOT lift or
support the
DO NOT support or raise the front of the Platform from
platform during any maintenance operation the front
as this may result in damage to the tension Jackstand
members. Lower Arm
6
Downloaded from www.Manualslib.com manuals search engine
Battery Maintenance Charge the batteries at the end of each work shift
or sooner if the batteries have been discharged.
7
Downloaded from www.Manualslib.com manuals search engine
Routine Service Routine Service Table Key
Use the following table as a guide for routine Interval
maintenance. Inspection and maintenance shall Daily=each shift (every day) or every eight hours
be performed by personnel who are trained 30D=every month (30 days) or every 50 hours
and familiar with mechanical and electrical 3M=every 3 months or 125 hours
procedures. Refer to the Service Manual for 6M=every 6 months or 250 hours
complete service instructions. 1Y=every year or 500 hours
2Y=every year or 1000 hours
Please copy the following page and use the
Routine Service table as a checklist when inspect- Model
ing a machine for service. A= All Models
E= Electric Models
D= Dual Fuel Models
Y=Yes/Acceptable
N=No/Not Acceptable
R=Repaired/Acceptable
COMPONENT INSPECTION OR SERVICES INTERVAL MODEL Y N R COMPONENT INSPECTION OR SERVICES INTERVAL MODEL Y N R
Battery Check electrolyte level Daily A Elevating Inspect for structural cracks Daily A
System Check specific gravity 30D A Assembly Check pivot points for wear 30D A
Clean exterior 6M A Check mounting pin pivot bolts 30D A
Check battery cable condition Daily A for proper torque
Charge batteries Daily E Check linkage gear for wear 6M A
Clean terminals 6M A Check elevating arms for bending 6M A
Engine Oil Check level and condition Daily D Grease linkage pins 30D A
Check for leaks Daily D Grease linkage gear 30D A
Change oil filter 30D D Chassis Check hoses for pinch or Daily A
Engine Fuel Check fuel level Daily D rubbing points
System Check for leaks Daily D Check component mounting 6M A
Replace fuel filter 6M D for proper torque
Check air cleaner Daily D Check welds for cracks Daily A
Hydraulic Oil Check oil level Daily A Lift Check the cylinder rod for wear 30D A
Change filter 6M A Cylinder Check mounting pin pivot bolts 30D A
Drain and replace oil 2Y A for proper torque
Hydraulic Check for leaks Daily A Check pivot pin snap rings 30D A
System Check hose connections 30D A Check seals for leaks 30D A
Check hoses for exterior wear 30D A Inspect pivot points for wear 30D A
Emergency Open the emergency lowering Daily A Check fittings for proper torque 30D A
Hydraulic valve and check for Entire Check for and repair Daily A
System serviceability Unit collision damage
Controller Check switch operation Daily A Check fasteners for proper torque 3M A
Control Check the exterior of the cable Daily A Check for corrosion-remove 6M A
Cable for pinching, binding or wear and repaint
Platform Check fasteners for proper torque Daily A Lubricate 30D A
Deck and Check welds for cracks Daily A Labels Check for peeling, missing, or Daily A
Rails Check condition of deck Daily A unreadable labels & replace
Tires Check for damage Daily A Wheel Check wheel assembly for play 30D A
Check air pressure (50 psi-B78 x 13 ST) Daily A Bearings Repack wheel bearings 2Y A
Check lug nuts (torque to 90 ft. lbs. [123 Nm]) 30D A (replace wheel bearings and
Hydraulic Wipe clean 30D A seals at 2000 hrs.)
Pump Check for leaks at mating surfaces 30D A
Check for hose fitting leaks Daily A
Check mounting bolts for proper torque 30D A
Check the drive coupling for proper
torque and alignment 1Y A
Lubricate pump splines (Kohler Only) 6M D
Drive Motors Check for operation and leaks Daily A Service Report
Steering Check hardware & fittings 6M A
System for proper torque Date: ______________
Grease pivot pins 30D A
Oil king pins 30D A Owner: _______________________________
Check steering cylinder for leaks & 30D A
mounting bolts for proper torque Model No: ___________ Serial No: ________
Serviced By: ___________________________
Service Interval: ________________________
8
Downloaded from www.Manualslib.com manuals search engine
Note: Labels can be ordered by using Part Number located by each label.
For machines equipped with options consult Service Manual.
065791-000 061515-000
1-REQUIRED 1-REQUIRED
066554-000
1-REQUIRED
066550-004
1-REQUIRED
9
101252-012 SL30
1-REQUIRED 101252-010 SL26
1-REQUIRED
064166-000 061205-005
1-REQUIRED 1-REQUIRED
(GASOLINE ONLY)
066555-000 9
2-REQUIRED
061220-002
1-REQUIRED
SL26N
101250-007
062524-001 063423-000 1-REQUIRED
1-REQUIRED 1-REQUIRED
066552-000
1-REQUIRED 064421-000
1-REQUIRED SL30N
101250-003
1-REQUIRED
STAND AND FOLLOW THESE LABELS WHEN OPERATING THE WORK PLATFORM.
027898-000 066568-000 064414-000
10
Downloaded from www.Manualslib.com manuals search engine
NOTES:
11
Downloaded from www.Manualslib.com manuals search engine
Specifications*
ITEM SL-26N SL-30N
Platform Size (Inside Toeboards)
Standard 57.5 in. x 141.5 in. [1.46 m x 3.59 m] 57.5 in. x 166.25 in. [1.46 m x 4.22 m]
w/ Extension 57.5 in. x 181.5 in. [1.46 m x 4.61 m] N/A
Max. Platform Capacity
Standard 1250 lbs. [567 kg] 1000 lbs. [363 kg]
w/ Extension 1250 lbs. [567 kg] N/A
USA
TEL: (800) 926-5438 or (559) 891-5200
FAX: (559) 896-9012
PARTS: (888) UR-PARTS
PARTSFAX: (559) 896-9244
1775 Park St., Selma, CA 93662
http://www.upright.com
12 060588-012
12/99 D
Downloaded from www.Manualslib.com manuals search engine