Professional Documents
Culture Documents
Smart TLC 2103
Smart TLC 2103
Smart TLC 2103
深圳市能点科技有限公司
SHENZHEN EPT TECHNOLOGY CO., LTD.
规格书
SPECIFICATION
Smart TLC-2103
智能液位监测器
版本 Version:A 日期 Date:2022/04/09
www.eptsz.com
www.eptsensor.com
Contact: Jolly Tang
Email: isdsales03@eptsz.com
Ph/Whts: +86 180 2765 4576
能點科技有限公司 EPT TECHNOLOGY CO., LTD.
⚫ 产品规格说明/Product Specification
电源 产品供电电源 9V(1.5M)
Power Power Supply DC2.0
Adaptor
显示器与液位传感
连接线 器数据连接线 15M 防水接头 5.0mm 22AWG
Cable Connect the Sensor 公头 母头
and Display waterproof 2464
connector
male and
female
本规格书为相应产品作业之标准,在客户确认后,会作为生产、供货唯一依据,应在生产前作仔细确认。
This specification would be the standard for the production, after confirmed by clients, it would be the only
rule that should be followed, please check it carefully before production.
能點科技有限公司 EPT TECHNOLOGY CO., LTD.
工作电压/Power Supply DC 9V
工作电流/Current 正常状态<100mA
Normal State<100mA
工作频率/Frequency 40kHz
通信方式/Communication RS485
本规格书为相应产品作业之标准,在客户确认后,会作为生产、供货唯一依据,应在生产前作仔细确认。
This specification would be the standard for the production, after confirmed by clients, it would be the only
rule that should be followed, please check it carefully before production.
能點科技有限公司 EPT TECHNOLOGY CO., LTD.
定义 Definition:
①显示屏状态切换: 常亮/显示 10s ②设置
Display state Always on/ Set
switching display for 10s
③切换模式 ④加+
Model switching Plus+
⑤减- ⑥实时水量
Minus- Levels in real time
⑦时间显示 ⑧水箱温度/到传感器探头的距离
Time Temperature of tank /Distance from
liquid level to sensor probe
⑨室内温度
Temperature of the place
which placed the
display.
Please insert the power plug of the water pump into the smart socket. The power of the water
pump cannot exceed 3 kW. When the water level of the water tank reaches the set low level
alarm level, the display will display a low level alarm and the water pump will start, and the water
pump will start to add water to the water tank. When the water level of the water tank reaches the
set high level, the display will display a high level alarm and stop the water pump.
本规格书为相应产品作业之标准,在客户确认后,会作为生产、供货唯一依据,应在生产前作仔细确认。
This specification would be the standard for the production, after confirmed by clients, it would be the only
rule that should be followed, please check it carefully before production.
能點科技有限公司 EPT TECHNOLOGY CO., LTD.
初始化 Initialization:
长按 3 秒按键②进入设置模式 :时间设置 、水位设置 、报警水位设置
Press and hold the button ② for 3 seconds to enter the setting mode: time setting,
water level setting, alarm water level setting
显示器设置说明
Setup
Instructions of
Display
2.1. 如图所示. 当显示器屏幕下方向出现 “TIME”字母设备进入时间
设置:通过按键增加与减少进行时间校准,点击按键③可切换小
时/分钟的设置,点击按键②进入下一项设置;
点击按键③切换模式
本规格书为相应产品作业之标准,在客户确认后,会作为生产、供货唯一依据,应在生产前作仔细确认。
This specification would be the standard for the production, after confirmed by clients, it would be the only
rule that should be followed, please check it carefully before production.
能點科技有限公司 EPT TECHNOLOGY CO., LTD.
如图所示. 当显示器屏幕下方向出现“TANK”字母并且水箱上水
位图标闪烁,设备进入水箱高水位设置:显示器中的 0.1M 为设置
液位传感器到水箱高水位的距离设置.客户后可通过按键+-设置
传感器到水箱高液位的实际距离;点击按键②切换设置
本规格书为相应产品作业之标准,在客户确认后,会作为生产、供货唯一依据,应在生产前作仔细确认。
This specification would be the standard for the production, after confirmed by clients, it would be the only
rule that should be followed, please check it carefully before production.