Professional Documents
Culture Documents
Pag-Asa Steel Works Inc. - Products & Services - Product Guide
Pag-Asa Steel Works Inc. - Products & Services - Product Guide
Pag-asa Steel rebar products are identifiable through the Company Logo ("PSW", short for Pag-
asa Steel Works), which is hot-rolled and embossed onto each bar at specified intervals. The
Rebar Size mark, which specifies the nominal diameter of the bar, as well as the Grade,
Ductility, and Manufacturing Process marks are also hot-rolled adjacent to the company logo.
Pag-asa Steel pioneered the practice of placing its logo on its bars in 1975, before it was
mandated by law. The Bureau of Product Standards of the Department of Trade and Industry of
the Philippines now requires all rebar manufacturers to put identifying marks on their bars.
Regular (R)
Grade 280 3 -
or Weldable (W)
STANDARDS [Top]
Pag-asa Steel produces superior reinforcing steel bars in an array of sizes, lengths, and grades
in adherence to Philippine National Standard (PNS 49:2020), as well as the global ASTM
Standard (ASTM A615/A706) established by the American Society for Testing and Materials
(now known as ASTM International).
Standards Grades
PNS 49:2020 GR 230 GR 280 GR 420 GR 520 GR 550
The PNS 49 grade names come from the minimum yield strength of the bars, as measured in
megapascals (MPa). For instance, a standard Grade 420 bar has a minimum yield strength of
420 MPa.
The ASTM International grades are also based on yield strength, but are primarily expressed in
pounds per square inch (psi). For instance, a standard Grade 60 bar has a minimum yield
strength of 60,000 psi [equivalent to 420 MPa], and is designated as "Grade 60 [420]" in the
standard.
For simplicity, psi-based designations are used here when referencing the ASTM International
standard.
Pag-asa Steel manufactures and sells the following standard sizes (in nominal diameters):
10mm, 12mm, 16mm, 20mm, 25mm, 28mm, 32mm, and 36mm. Larger sizes such as 40mm
and 50mm bars may be produced via special order.
Nominal Diameter, mm
10 12 16 20 25 28 32 36 40 50
For steel bars, the terms "size" and "nominal diameter" are used interchangeably.
Because variation in cross sectional area occurs during hot rolling, a corresponding variation in
linear weight is to be expected. For this reason, PNS 49 provides for an allowable 'variation in
mass' (VIM) of ±6%, measured using one piece of steel bar.
Pag-asa Steel rebars come in the following commercial lengths: 6.0m, 7.5m, 9.0m, 10.5m, and
12.0 m. Special lengths of 13.5 and 15.0 meters may be produced via special order.
The cut length of a rebar should not be shorter than the specified commercial lengths according
to the PNS 49:2020 standards. The specified tolerance for length is zero (0), + 60 mm.
GRADES [Top]
Pag-asa Steel rebars comes in the following grades to meet high-tensile, intermediate, and low-
tensile building requirements.
Rebar grade are embossed on the bars in addition to different color markings painted at the
ends of each bar, as shown in the following table:
230R 33
*
280R 40
*
Class 1
Regular 420R 60
Steel Bar *
520R 75
*
550R 80
*
280W 40
**
Class 2
Weldable 420W 60
Steel Bar **
550W 80
**
* At both ends of the bar ** One color per end of the bar
Reference: Philippine National Standard (PNS 49:2020)
Please refer to the chart below to see the properties of different rebar grades, as outlined in the
Philippine National Standard and ASTM Standard.
Download the PDF version of the Rebar Grade Comparison.
For cut and bend, mechanical couplers, and lab testing services, please click
here.
PAG-ASA STEEL WORKS, INC.
408 AMANG RODRIGUEZ AVE., MANGGAHAN, PASIG CITY
TEL: (+632) 8-737-6300
EMAIL ADDRESS: CONTACT@PAGASASTEEL.COM