Professional Documents
Culture Documents
206LSI2012
206LSI2012
SERVICE INSTRUCTION
FOR CARGO HOOK KIT
NOTICE
For superseded kits, refer to page ii for Kit Number, Model, and Serial Number.
EFFECTIVITY
KIT NUMBER MODEL SERIAL NUMBER
1 206-706-341-007 206L 45004 through 45153
(Provisions) 46601 through 46617
2 4 206-706-341-009 206L1 45154 through 45790
(Provisions) 206L3 51001 through 51612
3 206-706-341-113 206L4/206L4T 52001 and Subsequent
(Provisions)
1 2 3 4 206-706-341-101 206L 45004 through 45153
(Suspension Assembly) 46601 through 46617
(Short Snout Hook) 206L1 45154 through 45790
206L3 51001 through 51612
206L4/206L4T 52001 and Subsequent
2 3 4 206-706-341-105 206L1 45154 through 45790
(Suspension Assembly) 206L3 51001 through 51612
(Long Snout Hook) 206L4/206L4T 52001 and Subsequent
COPYRIGHT NOTICE
COPYRIGHT 2013
BELL ® HELICOPTER TEXTRON INC.
AND BELL HELICOPTER TEXTRON
CANADA LTD.
ALL RIGHTS RESERVED
LOG OF REVISIONS
On a revised page, the text and/or illustration affected by the latest revision is shown by a vertical line. A revised
page with only a vertical line next to the page number indicates that text has shifted or that non-technical
correction(s) were made on that page.
LOG OF PAGES
LIST OF CHAPTERS
Kit 206-706-341-103 has been verified by first article installation on Model 206L4, S/N 52029, dated 14 May 1993.
Kit 206-706-341-105 has been verified by first article installation on Model 206L4, S/N 52171, dated 7 June 1996.
Kit 206-706-341-113 has been verified by first article installation on Model 206L4, S/N 52171, dated 7 June 1996.
EFFECTIVITY
2 Provisions Kits 206-706-341-007 and -009 must be installed prior to or concurrently with
Suspension Assembly Kit 206-706-341-005.
8 Kit is also applicable to 206L1+ helicopters (Increased Gross Weight Upgrade Kit
(BHT-206-SI-2052) installed).
E VALUATE
L OGISTICS
P UBLICATIONS
Manual Title:
Manual Number (if assigned):
Date of Issue:
Date of Last Revision:
Section, Chapter, Paragraph Affected:
Your Feedback:
Now Reads:
Should Read:
Your Name:
Address:
(If you choose to mail this form, fold in thirds with address exposed, tape and mail.)
Export Classification C, ECCN 9E991
TAPE HERE
From
POSTAGE
NECESSARY
TABLE OF CONTENTS
Paragraph Page
Number Title Number
FIGURES
Figure Page
Number Title Number
1-1 Cargo Hook Provisions and Suspension Assembly (Kits -001 and -003)
— Installation ...................................................................................................... 1-5
1-2 Cargo Hook Provisions (Kits -007, -009, -103, and -113) — Installation ............ 1-12
1-3 Electrical Installation ........................................................................................... 1-23
1-4 Cargo Hook Suspension Assembly (Kit -005)..................................................... 1-28
1-5 Cargo Hook Suspension Assemblies (Kits -101 and -105)................................. 1-31
INSTALLATION PROCEDURES
1-1. GENERAL INFORMATION structural damage, do not use metal scribers or lead
pencils.
NOTE
9. Following any drilling or cutting, remove burrs
Make sure to use the applicable general and metal particles. Clean and touch up the surfaces
information steps that apply to the as required (BHT-ALL-SPM).
installation procedures for this kit.
10. For modification or repairs to glass or carbon fiber
1. This Service Instruction provides the procedures reinforced composites, refer to the BHT-ALL-SRM,
to install the Cargo Hook Kit. Chapter 4.
2. It is the responsibility of the installer to verify that 11. Refer to the BHT-ELEC-SPM for the electrical
newly installed equipment/systems do not interfere installation procedures.
with, or are susceptible to, the normal operation of
other equipment installed in the helicopter. Refer to
General Information Letter (IL) GEN-07-113 for 12. It is recommended that an experienced electrical/
additional information. avionics person performs all steps pertaining to
connector disassembly/reassembly. If not specified in
these installation procedures, refer to the
3. All openings and ports in components, hoses, BHT-ELEC-SPM for electrical wiring practices.
and/or tubes disconnected or removed to facilitate the
modification must be capped, plugged, or otherwise
sealed to prevent contamination during the 13. Perform a continuity check on all wiring newly
modification. installed or disturbed during this modification.
4. Tag all parts, including attaching hardware 14. Unless otherwise noted, all hose and wire bundle
(unless otherwise noted) removed to gain access to clamps should be installed to provide optimum
work area. Protect parts from damage until reinstalled. clearance with structure, component, flight controls,
and other hoses and wire bundles.
8. Draw layout on sheet metal with a fine-tipped 4. Remove the collective friction knob from the
non-corrosive ink marker or equivalent. To prevent shaft.
5. Remove the pilot collective stick boot. 5. Peel the two shims (6) to maintain a gap of 0.00
to 0.003 inch (0.00 to 0.08 mm) for each, between the
floor panel and the inside fittings (1). Slip the shim
6. Remove the center seat interior trim panel.
between the floor panel and fitting, on each side, with
the holes in the shims and fittings aligned.
7. Remove the left and right crew seat covers.
6. Secure the fittings (1 and 4) together with the four
8. Remove the cover between the pilot and copilot bolts (7) and four washers (8) up through the fittings
seat covers. and fuselage. Secure the bolts with four washers (8)
and four nuts (9).
9. Remove the bottom center console cover from
the pedestal. 7. Install the bracket (10) on the underside of the
fuselage, utilizing the two existing inserts left of
centerline at approximately FS 115.0 and left BL 9.50,
10. Remove the upper center console cover from the with two screws (2) and two washers (3). The vertical
pedestal. angle of the bracket must be located on the aft side of
the screws.
OBEY ALL THE SAFETY PRECAUTIONS a. Remove the nut and the washer from the end
WHEN DOING MAINTENANCE ON OR of the cargo hook mechanical release cable (11).
NEAR ELECTRICAL/ELECTRONIC Insert the ball and the cable, attached to the end of the
EQUIPMENT (CHAPTER 96). release cable, aft through the inboard hole in the
bracket (10), and secure the release cable to the
11. Open the overhead panel to access the circuit bracket with the washer and the nut.
breaker.
b. Remove the nut from the connector (J180) of
the cable assembly (12). Insert the connector from the
1-3. CARGO HOOK PROVISIONS (KIT -003)
forward side in the center hole of the bracket (10),
— INSTALLATION position the ring on the chain of the dust cover (13)
over receptacle, and secure with the nut removed from
1. Remove and discard 16 screws (29, Figure 1-1) the connector.
and 16 washers (30) from the passenger seat
bulkhead. c. Tape the cable assembly (12) to the
mechanical release cable (11) along the entire length
2. Remove and discard four screws (31), eight at six places, equally spaced, with 3/4-inch (19.0-mm)
washers (32), and four nuts (33). wide electrical tape as follows:
3. Center and install the two inside fittings (1) to the NOTE
forward bulkhead of the passenger seats (left and right
Do not stretch the last turn of tape. Both
BL 8.00) over the existing 16 holes (eight each side)
surfaces of the tape must be kept clean
with 16 screws (2) and 16 washers (3).
while applying. Avoid unnecessary slack in
the electrical wires.
4. Align the two outside fittings (4) over the existing
bolt holes (two each side directly beneath the inside (1) Wind two turns of tape around the
fittings) on the underside of the fuselage. With the two mechanical release cable (11) and cable
small holes in each fitting aligned with the two inserts assembly (12). Allow the tape to cover 1.0 to
in the lower shell forward of the bolt holes, install two 1.5 inches (25.4 to 38.1 mm) of cable length at each
screws (5) and two washers (3) in each fitting. wrapping.
A
C
FS
121.44
PASSENGER SEAT
BULKHEAD
(PICK UP EXISTING
HOLES IN SEAT BULKHEAD)
T 2 3 29 30
B
1 6
PASSENGER
COMPARTMENT
FLOOR PANEL
OUTER SKIN
7 8 9 31 32 33
(PICK UP EXISTING
BL
T 3 5 HOLES IN LOWER SHELL)
8.00 (PICK UP EXISTING
INSERT HOLES) 4
VIEW A VIEW B
LOOKING AFT SUSPENSION ASSEMBLY OMITTED FOR CLARITY
206_SI_2012_0001a
Figure 1-1. Cargo Hook Provisions and Suspension Assembly (Kits -001 and -003) — Installation
(Sheet 1 of 5)
FS FS
62.80 69.5
BL
0.0 BL
0.62
BL
1.80
3 26 27
BL
4.50
35
FORWARD
CROSSTUBE
FS
22 23 24 25 73.0
4TB1 11
TERMINAL
BOARD
12
21 2 STRUCTURE
C 34 3
3.5 TO 4.5 IN.
(88.9 TO
114.3 mm)
3
206_SI_2012_0001b
Figure 1-1. Cargo Hook Provisions and Suspension Assembly (Kits -001 and -003) — Installation
(Sheet 2 of 5)
FS
83.0
BL
5.50 FS
91.0
BL FS
7.50 99.0
BL
9.00
VIEW C-C
LOOKING DOWN
FWD
206_SI_2012_0001c
Figure 1-1. Cargo Hook Provisions and Suspension Assembly (Kits -001 and -003) — Installation
(Sheet 3 of 5)
28
FS
107.0 10 FS 11
115.0
BL BL
9.50 9.50
12 12
13 C
3 3
14
15 T
2 T
3
16
LOOKING INBOARD
LEFT SIDE
FWD
206_SI_2012_0001d
Figure 1-1. Cargo Hook Provisions and Suspension Assembly (Kits -001 and -003) — Installation
(Sheet 4 of 5)
12 TO 15 IN-LBS
T (1.4 TO 1.7 Nm)
T
NOTES
1 Peel shim to maintain 0.000 to 0.003 inch (0.00 to 0.07 mm) gap.
3 Wrap cables as shown with electrical tape 0.75 inch (19 mm) wide, per MIL-I-24391.
4 Stow ball and cable in position when hook assembly is removed from helicopter.
206_SI_2012_0001e
Figure 1-1. Cargo Hook Provisions and Suspension Assembly (Kits -001 and -003) — Installation
(Sheet 5 of 5)
d. Locate the five existing inserts and one plug ±12.7 mm) below and above the grommet (21) hole.
button (34) in the bottom skin, at the following The wrapping must be continuous within these
locations: dimensions to prevent chafing.
• FS 99.00 and BL 9.00 a. Remove the second, third, and fourth rivets
from the top row of rivets on each side of the console.
• FS 91.00 and BL 7.50
b. Position the support assembly (23) against the
• FS 83.00 and BL 5.50 left inboard edge of the console so that the top surface
of the support assembly is flush with the top edge of
• FS 69.50 and BL 1.80 the console. Pick up the existing rivet holes through
the end of the support assembly and attach with
• FS 62.80 and BL 0.62 Clecos, or equivalent.
e. Route the mechanical release cable (11) and c. Position the angle (24) under the right end of
the cable assembly (12) forward and inboard along the the support assembly (23) and against the right
line of inserts. inboard edge of the console. Pick up the existing rivet
holes through the end of the clip and secure with
f. At the aft four insert locations, secure the Clecos, or equivalent.
mechanical release cable (11) and the cable
assembly (12) with the clamp (14), screw (15),
d. Drill three holes 0.128 inch (3.25 mm) in
washer (3), and spacer (16).
diameter through the right end of support
assembly (23) and the angle (24) with a No. 30 drill.
g. Secure the mechanical release cable (11) and
the cable assembly (12) to the crosstube with the
e. Countersink the holes on the top side of the
clamps (14 and 17), screw (18), spacer (19),
support assembly (23) and secure the angle (24) with
washer (3), and nut (20).
the three rivets (25).
h. Remove the plug button (34) from the
fuselage outer skin, at FS 62.80 and BL 0.62, below f. Leave the support assembly (23) ends
the crew seats compartment. secured with Clecos to allow access to the electrical
terminal board.
i. Temporarily remove the T-handle, washer,
and two nuts from the mechanical release cable (11). g. Match cut and drill the holes in the console
Install the grommet (21) on the mechanical release center cover (35) from the support assembly (23).
cable. Route the mechanical release cable and cable
assembly (12) up through the hole and into the h. Pick up the three screw holes previously
compartment between the crew seats. drilled in the console center cover (35) through the
mount assembly (26).
j. At the fifth insert location, secure the
mechanical release cable (11) and cable 10. Install the release cable mount assembly (26) on
assembly (12) with the clamp (14), screw (15), the top of the center panel between the pilot and
washer (3), and spacer (16). Make sure the copilot seats at three matching holes with three
mechanical release cable does not kink or bind. screws (27) and three washers (3). Note that the
mount assembly must be installed with the cap
k. Work the grommet (21), installed on the slanting forward.
mechanical release cable (11), into the hole in the
fuselage. 11. Install one of the two release cable nuts on the
threaded end of the cable, and route the cable up
l. Wrap the mechanical release cable (11) and through the mount assembly cap on the center panel.
the cable assembly (12) together with 0.75-inch Secure the center panel in place and install the
(19-mm) electrical tape 4.0 ±0.5 inches (101.6 remaining nut with the washer to the cable, securing
the cable to the cap by tightening the nuts. Install the Allow the adhesive to cure at room temperature for 24
T-handle to the mechanical release cable (11). hours.
C-108 Cadmium Plating 8. Check the radius blocks (5 and 6) for fit by
Solution positioning in place on the lower flange of the
bulkhead fittings (1).
C-305 Aliphatic Naphtha
C-317 Adhesive 10. Drill holes 0.250 to 0.255 inch (6.35 to 6.48 mm)
in diameter in the radius blocks (5 and 6).
1. Remove and discard 16 screws (38, Figure 1-2)
and 16 washers (39) from the passenger seat
NOTE
bulkhead.
Minor filing or sanding of the radius blocks
(5 and 6) may be required to provide proper
2. Remove and discard four screws (40), eight
fit and alignment.
washers (41), and four nuts (42).
11. Check the radius blocks (5 and 6) for fit using the
3. Center and install two bulkhead fittings (1) on the hole and bolt to set the position prior to the brush
forward bulkhead of the passenger seats (left and right cadmium plating treatment.
BL 8.00) over the existing 16 holes (eight each side)
with 16 screws (2) and 16 washers (3).
12. Chamfer the holes drilled in the radius blocks (5
and 6) 45 to 50° x 0.035 to 0.040 inch (0.89 to
4. Peel two shims (4) to maintain a gap of 0.00 to 1.02 mm) and brush cadmium plate the hole and
0.003 inch (0.00 to 0.08 mm) for each between the chamfer (BHT-ALL-SPM, Chapter 3).
floor panel and inside fittings (1). Slip the shim
between the floor panel and fitting, on each side, with
the holes in the shims aligned with the holes in the 13. Install the fitting (1) on the left side of the
floor. bulkhead.
5. Clean the mating surfaces with MEK (C-309) and 14. Position the radius block (5) in the radius of the
bond the shims to the floor with adhesive (C-317). flange at the lower end of the fitting (1).
A
C
FS
121.44
PASSENGER SEAT
BULKHEAD
1
T 1 39 38 3 2
A2 6 5
1
B 2 A2 4
8 S
31 7 2 9 11
1
BL
34 36
2 T1 9 10
43 32
35
8.00 33 T2
40
VIEW A
LOOKING AFT 41
42
VIEW B
SUSPENSION ASSEMBLY OMITTED FOR CLARITY
206_SI_2012_0002a
Figure 1-2. Cargo Hook Provisions (Kits -007, -009, -103, and -113) — Installation (Sheet 1 of 6)
FS FS
62.80 69.5
BL
0.0
BL
0.62
BL
1.80
3 26 27
BL
4.50
44
FORWARD
CROSSTUBE
FS
22 23 24 25 73.0
5 S
4TB1 9
TERMINAL
BOARD 21
30 6 KITS -103 AND -113
10 DETAIL C
SEE DETAIL C
21 STRUCTURE
D 37 3 4 7
3.5 TO 4.5 IN.
(88.9 TO
114.3 mm) 30 6
4
3.5 TO 4.5 IN.
(88.9 TO 3
114.3 mm)
12
17
18
LOOKING INBOARD
19
LEFT SIDE
20
FWD
206_SI_2012_0002b
Figure 1-2. Cargo Hook Provisions (Kits -007, -009, -103, and -113) — Installation (Sheet 2 of 6)
FS
83.0
BL FS
5.50 91.0
FS
BL 99.2
7.50
BL
7.50
VIEW D-D
LOOKING DOWN
4 7
13 T 1
14
FWD
206_SI_2012_0002c
Figure 1-2. Cargo Hook Provisions (Kits -007, -009, -103, and -113) — Installation (Sheet 3 of 6)
1.40 IN.
(35.6 mm) DIA.
A 1 29 HOLE
0.25 IN.
(6.4 mm)
2.24 IN.
(56.9 mm)
6.75 IN.
(171.5 mm)
TYPICAL
8 1.10 IN.
(27.9 mm)
FS BL FS TYPICAL
107.0 9.50 115.0
9
BL
9.0
10
CABLE STOWAGE
BRACKET
11
D
29
3
12 4 7
45
15 T1
2 T 1
3
16
LOOKING INBOARD 28
LEFT SIDE
FWD
206_SI_2012_0002d
Figure 1-2. Cargo Hook Provisions (Kits -007, -009, -103, and -113) — Installation (Sheet 4 of 6)
206_SI_2012_0002e
Figure 1-2. Cargo Hook Provisions (Kits -007, -009, -103, and -113) — Installation (Sheet 5 of 6)
A1 ADHESIVE (C-310)
A2 ADHESIVE (C-317)
S SEALANT (C-251)
12 TO 15 IN-LBS
T 1 (1.4 TO 1.7 Nm)
84 TO 107 IN-LBS
T 2 (9.5 TO 12.1 Nm)
NOTES
1 Brush cadmium plate hole and chamfer of radius blocks (5 and 6).
2 Peel shim (4) to maintain 0.000 to 0.003 inch (0.00 to 0.07 mm) gap.
3 Remove SS48172 plug button (38) and replace with grommet (21).
4 For kits -007 and -009, wrap cables as shown with electrical tape 0.75 inch (19 mm) wide, per
MIL-I-24391.
5 Add sealant (C-251) in floor cavity and around grommet (21). Cover grommet completely with
sealant. Do not apply sealant until provisions are completely installed.
6 For kits -103 and -113, use nylon ties (30) 3.0 inches (76.2 mm) above floor, immediately below
grommet (21), and 4.0 inches (101.6 mm) below floor.
7 For kits -103 and -113, install nylon ties (30) in lieu of tape 3.0 inches (76.2 mm) on either side of
clamps and 3.0 to 4.0 inches (76.2 to 101.6 mm) from end of external cable.
10 Use screws (36) with washers (35) to plug inserts when suspension assembly (28) is not used.
11 Use screws (7) with washers (32) and nuts (33) when suspension assembly (28) is not used,
screws head down.
206_SI_2012_0002f
Figure 1-2. Cargo Hook Provisions (Kits -007, -009, -103, and -113) — Installation (Sheet 6 of 6)
15. Clean the mating surfaces with MEK (C-309) and the ball and cable, attached to end of release cable, aft
bond the radius block (5) to the fitting (1) with adhesive through the inboard hole in the support assembly (8)
(C-317). and secure the mechanical release cable to the
support assembly with the washer and nut.
16. Install the fitting (1) and radius block (6) on the
right side by repeating step 13 through step 15. b. Remove the nut and the washer from the
cable assembly (10). Insert the connector (J180) from
the forward side into the center hole of the support
NOTE assembly (8). Position the ring on the chain of the dust
The final assembly will be done at a later cover (11) over the receptacle and secure with the nut
step. removed from the connector.
17. Temporarily install four screws (7) until the c. Tape the cable assembly (10) to the
adhesive cures. mechanical release cable along the entire length, at
six equally spaced places, with 3/4-inch (19-mm) wide
18. Apply corrosion preventive compound (C-101) to electrical tape as follows:
cover the area of the exposed threads, washers,
radius blocks (5 and 6), shims (4), and cabin floor. NOTE
Do not stretch the last turn of the tape. Both
19. Install the support assembly (8) to the underside
surfaces of tape must be kept clean while
of the fuselage, utilizing the two existing inserts left of
applying. Avoid unnecessary slack in the
centerline at approximately FS 115.00 and left
electrical wires.
BL 9.50, with two screws (2) and two washers (3).
Mount the support assembly so that the cable stowage (1) Wind two turns of tape around the
and the electrical connector on the flange are forward mechanical release cable (9) and the cable
of the attaching screws. assembly (10). Allow the tape to cover 1.0 to
1.5 inches (25.4 to 38.1 mm) of cable length at each
20. For kit -113, install two bumpers (29) to the wrapping.
structure as follows:
d. Locate five existing inserts and one plug
a. Clean the surface free of grease, oil, and dirt button (37) in the bottom skin, at the following
with a cloth dampened with aliphatic naphtha (C-305). locations:
g. At the next three insert locations, secure the assembly (8). Position the ring on the chain of the dust
mechanical release cable (9) and the cable cover (11) over the receptacle and secure with the nut
assembly (10) with the clamp (12), screw (13), removed from the connector (J180).
washer (3), and spacer (14).
c. Drill a hole in the support assembly (8) with a
h. Secure the mechanical release cable (9) and No. 60 drill. Secure the nut with lockwire (C-405).
the cable assembly (10) to the crosstube with the
clamps (12 and 17), screw (18), spacer (19), d. Locate five existing inserts and one plug
washer (3), and nut (20). button (37) in the bottom skin, at the following
locations:
i. Remove the plug button (37) from the
fuselage outer skin, at FS 62.80 and BL 0.62, below • FS 107.00 and BL 9.00
the crew seats compartment.
• FS 99.20 and BL 7.50
j. Temporarily remove the T-handle, washer,
and two nuts from the mechanical release cable (9). • FS 91.00 and BL 7.50
Install the grommet (21) on the mechanical release
cable. Route the mechanical release cable and the • FS 83.00 and BL 5.50
cable assembly (10) up through the hole and into the
compartment between the crew seats.
• FS 69.50 and BL 1.80
a. Remove the nut and the washer from the end i. Remove the plug button (37) from the
of the mechanical release cable (9). Insert the ball and fuselage outer skin, at FS 62.80 and BL 0.62, below
the cable, attached to the end of the release cable, aft the crew seats compartment.
through the inboard hole in the support assembly (8).
Secure the release cable to the support assembly with j. Temporarily remove the T-handle, washer,
the washer and the nut. and two nuts from the mechanical release cable (9).
Install the grommet (21) on the mechanical release
b. Remove the nut and the washer from the cable. Route the mechanical release cable and the
cable assembly (10). Insert the connector (J180) from cable assembly (10) up through the hole and into the
the forward side into the center hole of the support compartment between the crew seats.
k. Work the grommet (21), installed on the through the mount assembly cap on the center panel.
mechanical release cable (9), into the hole in the Secure the center panel in place and install the
fuselage. remaining nut with the washer on the cable. Secure
the cable to the cap by tightening the nuts. Install the
23. Install the support assembly (23) as follows: T-handle to the mechanical release cable (9).
a. Remove the second, third, and fourth rivets 26. For kits -103 and -113, at the fifth insert location,
from the top row of rivets on each side of the console. secure the mechanical release cable (9) and the cable
assembly (10) with the clamp (12), screw (13),
b. Position the support assembly (23) against the washer (3), and spacer (14). Make sure the
left inboard edge of the console so that the top surface mechanical release cable does not kink or bind.
of the support assembly is flush with the top edge of
the console. Pick up the existing rivet holes through
the end of the support assembly and attach with 27. For kits -103 and -113, secure the mechanical
Clecos, or equivalent. release cable and the electrical cables together by
installing one nylon tie (30) approximately 3 inches
c. Position the angle (24) under the right end of above the floor between the pilot and copilot seat and
the support assembly (23) and against the right one nylon tie below and adjacent to the grommet (21).
inboard edge of the console. Pick up the existing rivet
holes through the end of the clip and secure with 28. For kits -103 and -113, install one nylon tie (30)
Clecos, or equivalent. approximately 4 inches below and aft of the
grommet (21) to secure the mechanical release
d. Drill three holes 0.128 inch (3.251 mm) in cable (9) and the cable assembly (10) together in the
diameter through the right end of the support curved area.
assembly (23) and the angle (24) with a No. 30 drill.
e. Countersink the holes on the top side of the 29. For kits -103 and -113, secure the remaining
support assembly (23) and secure the angle (24) with external run of the mechanical release cable (9) and
three rivets (22). the cable assembly (10) together with nylon ties (30)
approximately 3 inches on either side of the clamps
f. Leave the support assembly (23) ends (six places).
secured with Clecos to allow access to the electrical
terminal board.
NOTE
g. Cut and drill holes in the console center The following step is only applicable if the
cover (44) to match the holes in the support suspension assembly (28) will not be
assembly (23). installed at this time.
25. Install one of the two release cable nuts on the 2. Connect wires M2B18 and M3B18N to the
threaded end of the cable, and route the cable up and terminal board (4TB1) as follows:
4. Connect the two wires and the two jumper wires CONNECT TO
WIRE NO.
of the cable assembly (2) to the cargo hook switch (3) 4TB1
as follows:
M2A18 A5
M1B18 C5
CONNECT TO
WIRE NO. SWITCH (4A5S3)
TERMINAL NO. 11. Remove the plug button from the overhead
console panel identified as CARGO HOOK. Install the
M1B18 2 circuit breaker (8) to the panel.
M1C18 2 to 5 (Jumper)
12. Connect wire P7H18 from the cable assembly (9)
M2A18 1 to the line side of the CARGO HOOK circuit breaker
(4CB5). Route and connect the opposite end of the
M2D18 1 to 4 (Jumper) wire to the 28 VDC bus in the console.
5. Add the switch to the bracket (6). Attach the two 13. Remove the insulation tubing from the end of
decals (4 and 5) identified as CARGO (FWD) and stowed wire M1A18. Route and connect the stowed
RELEASE (AFT) to the bracket, one forward and one wire to the CARGO HOOK circuit breaker opposite
aft of the switch (3), respectively. wire P7H18.
6. Use the existing hardware (bolt, washers, and 14. Install the support assembly (23, Figure 1-2) on
nut) on the cyclic stick, immediately forward of the the console with the six rivets (25).
1-6. CARGO HOOK PROVISIONS wire to the CARGO HOOK circuit breaker (8) opposite
(KITS -103 AND -113) — ELECTRICAL wire P7H18 with terminal (11).
INSTALLATION
4. For 206L4T helicopters, do as follows:
EXISTING TERMINAL
BLOCK 4TB1 PILOT
CYCLIC GRIP
A AND B
SEE DETAIL C
2 1
8
13
8 260-2510
13 PANEL ASSEMBLY
NO. 1 MAIN BUSS NO. 2 MAIN BUSS
FUEL FUEL FUEL FUEL CARGO ROTOR
VHF CUTOFF PUMP PUMP CUTOFF HOOK RPM
10 5 10 10 5 3
3 3 5 1 3 3
5 5 5 5 20 5
DETAIL A
LOOKING UP AT
OVERHEAD CONSOLE
OVERHEAD CONSOLE
APPLICABLE TO 206L, 206L1, 206L3, AND 206L4
VIEW B-B
(ROTATED 90° CCW)
APPLICABLE TO 206L4T
206_SI_2012_0003a
Figure 1-3. Electrical Installation (Sheet 1 of 4)
D
3
206-001-344-001
STICK ASSEMBLY
0.312 IN. (7.49 mm) HOLE 1 7
(NEAR SIDE ONLY)
5 LOCATE AS SHOWN
1.34 IN.
(34.0 mm)
LOCATE AS 4
SHOWN
VIEW D-D
206_SI_2012_0003b
M1C18
9 1 14
2
10
10
1 14
11
9
2
APPLICABLE TO 206L4
KITS -103 AND -113
260-2132 SOLOY 12
1
14
260-2500 SOLOY 2
APPLICABLE TO 206L4T
KITS -103 AND -113
206_SI_2012_0003c
Figure 1-3. Electrical Installation (Sheet 3 of 4)
NOTES
1 Use ball rotary file to rout out hole for installation of grommet.
206_SI_2012_0003d
Figure 1-3. Electrical Installation (Sheet 4 of 4)
3. Peel the shims (3) as required to align the holes Cargo Hook Provisions Kit (-007) must be
in the bracket assemblies (2) with the holes in the installed prior to or concurrently with the
helicopter, and to eliminate the gap between the Cargo Suspension Assembly Kit (-101).
shoulder of the beam (10) and the bracket assembly
bearings. Cargo Hook Provisions Kits (-009, -103,
and -113) must be installed prior to or
4. Reinstall the previously removed nuts (6). Torque concurrently with the cargo suspension
the nuts T . assembly kit (-101 or -105).
5. Install the cargo suspension assembly (1) with 1. If installed, remove the four screws (36,
the four bolts (31, Figure 1-2), four washers (32), and Figure 1-2) from the four inserts on the underside of
four nuts (33) in the four aft holes. Insert the bolts from the helicopter.
the top through the fittings (1) and the radius blocks (5
and 6).
2. If installed, remove the four screws (7), four
washers (32), and four nuts (33) in the holes aft of the
6. Install the four screws (34) and the four inserts where the bracket assembly (14, Figure 1-5)
washers (35) in the four forward holes of the cargo will be installed.
suspension assembly (1) and pick up the four existing
inserts in the bottom of the fuselage.
3. Apply sealant (C-251) to the entire mounting
surface of the bracket assembly (14).
7. Connect the ball and the cable to the
connector (8, Figure 1-4) of the release cable (9).
4. Position the bracket assembly (14) on the left,
8. Place the dust cover (11, Figure 1-2) on the underside of the fuselage, with the aft holes in the
dummy receptacle and install the cable assembly (4, bracket assembly aligned with the drilled holes in the
Figure 1-4) on the electrical receptacle from which the helicopter. Secure with two bolts (31, Figure 1-2), two
dust cover was removed. washers (32), and two nuts (33).
TAPE AS
REQUIRED
5.0 IN.
(127 mm)
TYPICAL
2 4
VIEW A
1
3 7
11 T 2
10
5
6 T 1
12 2
206_SI_2012_0004a
Figure 1-4. Cargo Hook Suspension Assembly (Kit -005) (Sheet 1 of 2)
40 TO 60 IN-LBS
T 1 (4.5 TO 6.8 Nm)
NOTES
1 Peel shim (3) and/or remove washer (7) between bracket assembly (2) and beam (10) to align
holes in bracket assembly with holes in helicopter.
206_SI_2012_0004b
Figure 1-4. Cargo Hook Suspension Assembly (Kit -005) (Sheet 2 of 2)
5. Align the forward holes in the bracket install on the dummy receptacle. Install the electrical
assembly (43) with the two existing inserts in the cable assembly (2), of the suspension assembly on
fuselage. Install two screws (34) and washers (35). the connector from which the dust cover was removed.
6. Place the washer (15, Figure 1-5) and the 14. Secure the connector of the electrical cable
shim (16) on the left end of the beam (6) with the assembly to the receptacle on the cargo suspension
washer against the beam shoulder. Insert the end of assembly (1) with lockwire (C-508).
the beam into the bearing of the bracket
assembly (14). 1-10. RESTORATION
7. Place the washer (15) and the shim (16) on the NOTE
right end of the beam (6) with the washer against the
beam shoulder. Refer to the applicable 206L Maintenance
Manual for the procedures.
8. Position the remaining bracket assembly (14) on 1. Close the overhead panel.
the right end of the beam (6). Peel the shims (16) and/
or remove the washers equally at each end of the
beam until the holes in the bracket assembly align with 2. Install the upper center console cover on the
pedestal.
the holes in the helicopter. Ensure minimum clearance
between the beam shoulders and the bracket
bearings. 3. Install the bottom center console cover on the
pedestal.
10. Install the washer (13, Figure 1-5) and the 6. Install the center seat interior trim panel.
nut (11) one at each end of the beam (6). Tighten the
nut. Back off to the nearest slot and install the cotter 7. Install the pilot collective stick boot.
pin (12).
12. Remove the ball end of the release cable (3) from 11. Perform an operational check of the cargo hook
the stowage on the underside of the helicopter and system (paragraph 1-11).
attach to the quick connector of the release cable on
the suspension assembly (1). 12. Amend the weight and balance records in
accordance with Chapter 2.
13. Remove the dust cover from the electrical
connector, adjacent to the release cable stowage, and 13. Return helicopter to the flight configuration.
5.0 IN.
(127 mm)
TYPICAL
VIEW A
D 5 2
SEE DETAIL C
5 1
SEE DETAIL B
DETAIL B
206_SI_2012_0005a
Figure 1-5. Cargo Hook Suspension Assemblies (Kits -101 and -105) (Sheet 1 of 3)
14
5 11
12
15 4
13
16 4
DETAIL C
7 6
8
3 9
T 10
SECTION D-D
206_SI_2012_0005b
Figure 1-5. Cargo Hook Suspension Assemblies (Kits -101 and -105) (Sheet 2 of 3)
NOTES
1 Cargo hook 17149-2, product of Breeze-Eastern Corporation, may be replaced by 528-010-00,
product of Onboard Systems International (Chapter 2).
3 Two washers (9) are required between carriage roller and carriage boss.
4 Peel shims (16) and/or remove washer (15) to align holes in bracket assembly (2) with holes
in helicopter.
5 Tighten nuts (11), back off to nearest castellation and install cotter pin (12). Beam (6) must rotate freely.
206_SI_2012_0005c
Figure 1-5. Cargo Hook Suspension Assemblies (Kits -101 and -105) (Sheet 3 of 3)
1-11. CARGO HOOK SYSTEM — b. Pull the manual release handle, installed
OPERATIONAL CHECK between the seats. The hook should open before the
manual release control handle reaches full travel.
The operational check of the cargo hook a. Turn BAT switch on and close CARGO HOOK
system should also be accomplished by circuit breaker.
flying with a simulated load.
b. Direct assistant to observe and apply a
1. Check the manual release system as follows: 10-pound (4.5-kg) downward pull to the cargo hook
load beam.
a. Direct assistant to observe and apply a c. Actuate the CARGO RELEASE toggle switch
10-pound (4.5 kg) downward pull to the cargo hook located on the cyclic control stick assembly. Make sure
load beam. the hook opens.
TABLE OF CONTENTS
Paragraph Page
Number Title Number
FIGURES
Figure Page
Number Title Number
1. Inspect for evidence of binding, excessive b. Secure the hook assembly to the suspension
looseness, and security of attachment. assembly with the existing bolt, washer, nut, and new
cotter pin.
2. Inspect the electrical wires for chafing and loose
connections. Check for broken wires in the cable.
NOTE
3. Examine the manual release cable for chafing, Hardware stack-up varies when using the
broken strands, and ease of operation. Check the hook assembly 17149-2 or 17149-2L from
connector (8, Figure 1-4) on the manual release cable Breeze-Eastern Corporation or the hook
for cracks and broken spring. assembly 528-010-00 from Onboard
Systems International (Figure 2-1).
4. Inspect the rollers on the suspension assembly
for wear, pitting, and/or spalling. c. Remove the electrical cable from the stowed
position and connect to the hook assembly.
5. Examine the hook assembly for evidence of
cracks and wear. d. Remove the mechanical release cable from
the stowed position and connect to the hook assembly.
6. Inspect the placards for appearance, legibility,
and conformity to configuration. e. Perform an operational check of the cargo
hook system (Chapter 1).
7. Perform the corrosion inspection in accordance
with the Corrosion Control Guide CSSD-PSE-87-001. 2-5. ELECTRICAL CHECK
8. Service and lubricate the helicopter hook and 1. Open the overhead console and remove the
components. pedestal cover located between the pilot and copilot
seats.
2-4. CARGO RELEASE HOOK ASSEMBLY —
REPLACEMENT 2. Turn the BAT switch to on position and with a
multimeter, perform a voltage (24 VDC) check as
1. Remove the release hook assembly as follows: follows:
a. Disconnect the electrical cable. a. In the overhead console, press the CARGO
HOOK circuit breaker (4CB5) and check the voltage
b. Disconnect the mechanical release cable. on the line side and the voltage output. If no voltage
exists, check the wire and the connections. Replace
c. Remove the shoulder bolt that secures the the circuit breaker if no voltage is found.
hook assembly to the suspension assembly.
b. Check the voltage at pin D5 on the terminal
d. Stow the ends of the cables on the support board (4TB1). If none exists, repair or replace wire
assembly located on the helicopter underside, forward M1A18. Check the voltage output at pin D5. If none
of the suspension assembly. exists, replace the terminal board (4TB1) module.
3
4
5
1. Washer (AN960PD816)
2 2. Bolt (12659-1)
3. Bushing (NAS77A8-19P) 2 Reqd
4. Washer (AN960-616)
5. Cotter pin (MS24665-300)
6. Nut (AN320C6)
7. Washer (AN960PD816) 2 Reqd
1 6
3
4
2 1. Washer (AN960-816L)
2. Bolt (290-332-00)
3. Bushing (NAS77A8-19P) 2 Reqd
4. Washer (NAS1149F0663P)
5. Cotter pin (MS24665-302)
6. Nut (AN320C6)
7. Washer (AN960-816L)
1 6
206_SI_2012_0006
Figure 2-1. Cargo Hook Attachments (17149-2, 17149-2L, and 528-010-00)
c. For kits -003, -007, and -009, check the i. Connect the connector (P180 to J180). Check
voltage with the CARGO HOOK switch (4A5S3) in the the voltage and the continuity at pins A and B. If none
on position, at terminals 1, 4, 2 and 5. If none exists on exists, repair or replace wires M2C18 and M3A18N, or
the line side, repair or replace the wires and/or the replace the connectors.
switch.
j. Attach the connector (P181) to the cargo hook
d. For kits -103 and -113, check the voltage with and check for actuation of the hook. If the hook
the CARGO HOOK switch (4A5S3) in the on position actuation does not occur, the cargo hook is faulty.
at terminals 9 and 10. If none exists on the line side,
repair or replace the wires and/or the switch.
k. Turn the BAT switch to OFF.
e. Check the voltage on the line side at
terminals A5 and B5 of the terminal board (4TB1). If 2-6. WEIGHT AND BALANCE
none exists, replace the terminal board (4TB1)
module.
Compliance with this Installation Instruction/Service
f. Check the voltage at pin B on the connector Instruction affects the weight and balance of the
(J180) and wire M2B18. If none exists, repair or helicopter as shown in the following table. Adjust
replace the wire and/or the connector. ballast as necessary to return empty weight Center of
Gravity (CG) to within allowable limits (applicable 206L
g. At the terminal board (4TB1), check continuity Maintenance Manual, Chapter 8).
from terminal A1 to the ground. Check continuity to the
ground. If none exists, repair or replace wire K3B16N.
NOTE
h. At the connector (J180), pin C, check This is the delta weight effect of this kit.
continuity to the ground. If none exists, repair or This includes weight and effect of the items
replace wire M3B18N and/or the connector. removed when this kit is installed.
LONGITUDINAL *LATERAL
LONGITUDINAL *LATERAL
MOMENT inch•pounds kg × mm
-----------------------
100
TABLE OF CONTENTS
Paragraph Page
Number Title Number
1 206-072-929-001 Beam
2 206-072-931-001 Block
1 206-072-932-001 Pin
2 206-072-934-001 Decal
1 214-070-926-001 Connector
2 AN960PD10L Washer
2 AN960PD416 Washer
2 AN960PD616L Washer
1 MS17826-8 Nut
AR MS20995C20 Wire
2 MS21042L3 Nut
2 MS21042L4 Nut
2 MS35207-263 Screw
2 NAS1356DC5C27D Pin
2 NAS464P4A28 Bolt
1 NAS464P8-18 Bolt
2 22-006-16-24-16 Bushing
NOTE:
1 Per ASB 206L-93-88, dated 6-21-93; when installing cargo suspension assembly, remove warning plate
13830-1 and install the new replacement warning plate in accordance with Breeze-Eastern CAB-100-41
and CSB-146 as appropriate to cargo hook model and configuration.
1 206-070-540-007 Angle
3 MS20426AD4-5 Rivet
6 MS20470AD4-5 Rivet
2 206-072-926-001 Fitting
2 206-072-927-001 Fitting
2 206-072-933-001 Shim
1 206-075-306-005 Decal
1 206-075-306-007 Decal
1 206-075-306-013 Bracket
1 MS24524-28 Switch
1 MS35489-4 Grommet
4 AN4-11A Bolt
3 AN520-10R7 Screw
(MS35207-262)
8 AN960-416L Washer
(NAS1149F0432P)
31 AN960PD10L Washer
(NAS1149D0316J)
4 MS21042-4 Nut
(MS21042L4)
1 MS21042L3 Nut
6 MS21919DG5 Clamp
1 MS21919DG36 Clamp
18 MS27039-1-08 Screw
4 MS27039-1-09 Screw
1 MS27039-1-17 Screw
5 MS27039-1-18 Screw
1 MS3181-10N Cover
(MS3181-10NA)
1 MS35489-11 Grommet
1 NAS43DD3-36 Spacer
(NAS43DD3-36N)
5 NAS43DD-48 Spacer
(NAS43DD3-48N)
1 206-072-936-001 Beam
2 206-072-937-001 Carriage
2 206-072-941-001 Decal
1 214-070-926-001 Connector
1 AN320C6 Nut
2 AN960-516 Washer
1 AN960-616 Washer
4 AN960-1016L Washer
4 AN960-1216L Washer
3 AN960PD816 Washer
4 CRS24CP-PP Bearing
2 MS21042L5 Nut
2 MS21250-05044 Bolt
2 NAS1021A12 Nut
4 NAS1291-10 Nut
2 120-008C40-24 Washer
2 140-007-21S18D5 Washer
NOTE:
1 Per ASB 206L-93-88, dated 6-21-93; when installing cargo suspension assembly, remove warning plate
13830-1 and install the new replacement warning plate in accordance with Breeze-Eastern CAB-100-41
and CSB-146 as appropriate to cargo hook model and configuration.
1 1 206-070-540-007 Angle
3 1 MS20426AD4-5 Rivet
6 1 MS20470AD-5 Rivet
2 206-072-927-003 Fitting
2 206-072-933-001 Shim
1 206-075-306-005 Decal
1 206-075-306-007 Decal
1 206-075-306-013 Bracket
1 MS24524-28 Switch
1 MS35489-4 Grommet
3 AN520-10R7 Screw
(MS35207-262)
31 AN960PD10L Washer
(AN960JD10LL)
(NAS1149D0316J)
4 AN960-416L Washer
(NAS1149F0432P
4 2 MS21250-04016 Bolt
1 MS21042L3 Nut
4 MS21042L4 Nut
6 MS21919DG5 Clamp
(MS21919WDG5)
1 MS21919DG36 Clamp
(MS21919WDG36)
4 3 MS27039-1-06 Screw
18 MS27039-1-08 Screw
4 2 MS27039-1-11 Screw
1 MS27039-1-17 Screw
4 MS27039-1-18 Screw
1 MS27039-1-22 Screw
4 3 MS27039-4-16 Screw
1 MS3181-10N Cover
(MS3181-10NA)
1 MS35489-11 Grommet
1 NAS43DD3-36 Spacer
(NAS43DD3-36N)
4 NAS43DD3-48 Spacer
(NAS43DD3-48N)
1 NAS43DD3-60 Spacer
(NAS43DD3-60N)
NOTES:
2 Equipment installation hardware. Store and maintain as loose equipment for the cargo hook installation.
1 1 206-070-540-007 Angle
3 1 MS20426AD4-5 Rivet
6 1 MS20470AD4-5 Rivet
2 206-072-933-001 Shim
2 206-072-943-001 Fitting
1 206-075-306-005 Decal
1 206-075-306-007 Decal
1 206-075-306-013 Bracket
1 MS24524-28 Switch
1 MS35489-4 Grommet
3 AN520-10R7 Screw
(MS35207-262)
31 AN960PD10L Washer
(AN960JD10LL)
(NAS1149D0316J)
4 AN960-416L Washer
(NAS1149F0432P)
1 MS21042L3 Nut
4 MS21042L4 Nut
4 2 MS21250-04016 Bolt
6 MS21919DG5 Clamp
(MS21919WDG5)
1 MS21919DG36 Clamp
(MS21919WDG36)
4 3 MS27039-1-06 Screw
18 MS27039-1-08 Screw
4 2 MS27039-1-11 Screw
1 MS27039-1-17 Screw
4 MS27039-1-18 Screw
1 MS27039-1-22 Screw
4 3 MS27039-4-16 Screw
1 MS3181-10N Cover
(MS3181-10NA)
1 MS35489-11 Grommet
1 NAS43DD3-36 Spacer
(NAS43DD3-36N)
4 NAS43DD3-48 Spacer
(NAS43DD3-48N)
1 NAS43DD3-60 Spacer
(NAS43DD3-60N)
NOTES:
2 Equipment installation hardware. Store and maintain as loose equipment for the cargo hook installation.
1 206-072-936-101 Beam
2 206-072-937-001 Carriage
(206-072-937-101)
2 206-072-941-001 Decal
1 214-070-926-001 Connector
(30-208-1)
1 AN320C6 Nut
2 AN960-516 Washer
(NAS1149F0563P)
1 AN960-616 Washer
(NAS1149F0663P)
8 AN960-1016 Washer
(AN960C1016)
(NAS1149F1063P)
4 AN960-1016L Washer
(NAS1149F1032P)
8 AN960C1016 Washer
(NAS1149C1063R)
3 AN960PD816 Washer
(NAS1149D0863J)
4 CRS24CP-PP Bearing
2 MS21042L5 Nut
2 MS21250-05044 Bolt
4 NAS1291-10 Nut
2 140-007-21S18D5 Washer
2 AN960-1216 Washer
(NAS1149F1290P)
2 AN960-1216L Washer
(NAS1149F1232P)
2 MS17825-12 Nut
(MS14144L12)
2 120-009C40-24 Shim
NOTE:
1 Per ASB 206L-93-88, dated 6-21-93; when installing cargo suspension assembly, remove warning plate
13830-1 and install the new replacement warning plate in accordance with Breeze-Eastern CAB-100-41
and CSB-146 as appropriate to cargo hook model and configuration.
1 1 206-070-540-007 Angle
3 1 MS20426AD4-5 Rivet
6 1 MS20470AD4-5 Rivet
2 206-072-933-001 Shim
2 206-072-943-001 Fitting
1 MS25036-149 Terminal
2 M39029/1-102 Contact
3 AN520-10R7 Screw
(MS35207-262)
31 AN960PD10L Washer
(AN960JD10LL)
(NAS1149D0316J
4 AN960-416L Washer
(NAS1149F0432P)
1 MS21042L3 Nut
4 MS21042L4 Nut
4 2 MS21250-04016 Bolt
6 MS21919DG5 Clamp
(MS21919WDG5)
1 MS21919DG36 Clamp
(MS21919WDG36)
4 4 MS27039-1-06 Screw
18 MS27039-1-08 Screw
4 2 MS27039-1-11 Screw
1 MS27039-1-17 Screw
4 MS27039-1-18 Screw
1 MS27039-1-22 Screw
4 4 MS27039-4-16 Screw
1 MS3181-10N Cover
(MS3181-10NA)
1 MS35489-11 Grommet
1 NAS43DD3-36 Spacer
(NAS43DD3-36N)
4 NAS43DD3-48 Spacer
(NAS43DD3-48N)
1 NAS43DD3-60 Spacer
(NAS43DD3-60N)
NOTES:
2 Equipment installation hardware. Store and maintain as loose equipment for the cargo hook installation.
1 206-072-936-101 Beam
2 206-072-937-001 Carriage
(206-072-937-101)
2 206-072-941-001 Decal
1 214-070-926-001 Connector
(30-208-1)
1 AN320C6 Nut
2 AN960-516 Washer
(NAS1149F0563P)
1 AN960-616 Washer
(NAS1149F0663P)
8 AN960-1016 Washer
(AN960C1016)
(NAS1149F1063P)
4 AN960-1016L Washer
(NAS1149F1032P)
8 AN960C1016 Washer
(NAS1149C1063R)
3 AN960PD816 Washer
(NAS1149D0863J)
4 CRS24CP-PP Bearing
2 MS21042L5 Nut
2 MS21250-05044 Bolt
4 NAS1291-10 Nut
2 140-007-21S18D5 Washer
2 AN960-1216 Washer
(NAS1149F1290P)
2 AN960-1216L Washer
(NAS1149F1232P)
2 MS17825-12 Nut
(MS14144L12)
2 120-009C40-24 Shim
1 1 206-070-540-007 Angle
3 1 MS20426AD4-5 Rivet
6 1 MS20470D4-5 Rivet
2 206-072-933-001 Shim
2 206-072-943-001 Fitting
1 MS25036-149 Terminal
2 M39029/1-102 Contact
2 222-020-945-103 Bumper
3 AN520-10R7 Screw
(MS35207-262)
4 AN960-416L Washer
(NAS1149F0432P)
31 AN960PD10L Washer
(NAS1149D0316J)
1 MS21042L3 Nut
4 MS21042L4 Nut
4 3 MS21250-04016 Bolt
6 MS21919DG5 Clamp
(MS21919WDG5)
1 MS21919DG36 Clamp
(MS21919WDG36)
4 4 MS27039-1-06 Screw
18 MS27039-1-08 Screw
4 3 MS27039-1-11 Screw
1 MS27039-1-17 Screw
4 MS27039-1-18 Screw
1 MS27039-1-22 Screw
4 4 MS27039-4-16 Screw
1 MS3181-10N Cover
(MS3181-10NA)
1 MS35489-11 Grommet
1 NAS43DD3-36 Spacer
(NAS43DD3-36N)
4 NAS43DD3-48 Spacer
(NAS43DD3-48N)
1 NAS43DD3-60 Spacer
(NAS43DD3-60N)
NOTES
3 Equipment installation hardware. Store and maintain as loose equipment for the cargo hook installation.