Professional Documents
Culture Documents
fw4255bkx Manual
fw4255bkx Manual
(P)
BB
FW4255BKX9
The weight of TV should be within the specified capacity Do not use this product outdoors. 1
of the mounts. In case the weight exceeds the specified
range, which leads to injury, we undertake no responsibility. FW4255BKX4
55 42
FW4255BKX6 FW4255BKX9
50 42
1
1
A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
FW4255BKX4
(140kg)total for the FW4255BKX4,71lbs(35kg)per display or
FW4255BKX6
FW4255BKX9
FW4255BKX4
FW4255BKX6
J N
Safety bolt
Use allen key (Z) and wrench(AA) to lock all nuts (T).
(See Figure 14)
3
A1,A2,
A3,A4
Z
5x5(included with all)
3x3(included with FW4255BKX6, AA If mounting holes are not recessed and interface
FW4255BKX9) brackets(A and B)can lay flat against display,
3 then no spacers are required.Gasket should be
used if the screw is too long.
T
If mounting holes are recessed,or if protrusions
prevent brackets(A and B) from laying flat ,then
spacers(A5) must be used.
A5(16/24/36) A6(16/24/36)
Center brackets vertically on back of screen.
FW4255BKX4 Select the small(A1),medium (A2 or A3) or
55 42 large(A4) screws. Attach brackets to screen
FW4255BKX6 FW4255BKX9 using four selected screws,four square washers
Decorative cap 1
A(4/6/9) B(4/6/9) 50 42 (A6) and four spacers(A5) at the top and bottom.
Tighten screws firmly. Do not overtighten.
(See Figure 15)
A1-A4
4
A6
√
10)
If the rail's going to be installed above the thread holes, FW4255BKX4
please choose the nearest holes. Details see threading
step. Lay two caster fastened panels (E) down on a flat surface.
Please use those four holes on the left side of the rail to Choose casters (pic. a) or steady feet(pic. b) to install. AA
join the column while assembling FW4255BKX4. (See Install two caster 1 (C) and two caster 2 (D) to caster
fastened panels (E). Casters with brakes should be in E
Figure 11)
the front and the ones without in the back. (See Figure 1)
Note: If you want to change steay feet or casters, you have to T
AA lift the whole product, we don’t advise you to exchange them.
F
T
a D Y
G
I J
2 R
E
H T
C M
Y
2 Q
FW4255BKX6/FW4255BKX9
Z S N
Do not lock tight when use allen key (Y), wrench (AA),
lock nut (T), pre-tighten is enough, to make sure it T 2 R
can be adjusted when install the column.
I
Y M
2 Q
Put two fixed plates (K) between two base cross bars (F), FW4255BKX9 M8x90mm (V) (S)
make sure holes site are aligned. Use eight bolts (W) to (T) O
connect and fix. (See Figure 4)
O
M5x8mm
Y
L
K F
2 X
AA
3 Y
T S
3 V
Z M
3 W O
Hold base cross bar (F), use two bolts (Q), two bolts (R)
go through washers (S), go through base cross bar (F),
then go through caster fastened panels (E), and use allen M8x90mm (V) (S)
key (Y), wrench (AA) to pre-tighten nut (T). (See Figure 5) (T)
Connect the circled hole in base cross bar (F) of FW4255BKX6/
FW4255BKX9, bolts (Q) must go through the two holes marked
by the arrow, Do not lock tight when use allen key (Y), wrench (AA),
lock(T), pre-tighten is enough, to make sure it can be adjusted
when install the column. (See Figure 5)
M L
Y
Y O
Q 4 R
4
AA
Y
S
AA T 4
Y 5
AA 3 5
3
4 V
T
V
T
S
2
E
2 S