Professional Documents
Culture Documents
AL-100R - Programa de Diagnóstico
AL-100R - Programa de Diagnóstico
2. System Reset (CAUTION: Performing System Reset clears all memory data)
a. Press the “TRANSPOSE/FUNCTION” button. R “TRANSPOSE” is displayed in DP1.
b. Press the “MAIN MENU” button 11 times. R “Initializa” is displayed in DP1.
“Group B” is displayed in DP2.
c. Press the “SUB MENU” button 4 times. R “All” is displayed in DP2.
d. Press the “EXECUTE” button. R “Sure?” is displayed in DP1.
“Init All” is displayed in DP2.
e. Press the “m/YES” button. R Make sure that the initial screen is displayed after
System Reset.
Note: The “System Reset” is necessary to perform this diagnostic program.
G r a n d DP1P i a n o
8 B e a t DP21
Message on LCD
1. RAM check
1 Press "POPS I" button to enter "RAM check". DP1: RAM Test
DP2: OK
2. ROM check
1 Press "POPS II" button to enter "ROM check". DP1: ROM Test
* OK appears after about 6 seconds. DP2: 00
3. Console check
1 Press "BALLAD" button to enter "Console check". DP1: Console SW
*Confirmation sound sounds. DP2: Console
2 Press buttons in the order from No.1 to No.86. DP2: BUTTON NO.
Press the DEMO button the last.
* Confirmation sound sounds.
* The Button number appears on the LCD (DP2). DP2: BUTTON NO.
* A buzzer sounds if buttons are pressed in a wrong order, and "CER" appears on LCD (DP2). DP2: CER
NOTE: This check cannot be aborted in mid-course.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 44 45 46 47 48 49 50 51 52 53 54 55 56 57 END
58
14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 59 60 61 62 63 64 65 66 67 68 69 70 71 72
73
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 74 75 76 77 78 79 80 81 82 83 84 85 86
Message on LCD
4. Slider check
1 Press the "ROCK" button to enter "Slider check". DP1: Slider
2 Turn the "ACCOMP" volume to "MIN". DP2: 000
3 Turn the "ACCOMP" volume to "MAX". DP2: 127
5. Pedal check
1 Press "BALLAD" button to enter "Pedal check". DP1: Key/Pedal
2 Press the "DAMPER" PEDAL. DP2: SUS
3 Press the "SOSTENUTE" PEDAL. DP2: SoS
4 Press the "SOFT" PEDAL. DP2: Sft
6. MIDI/HOST check (If there is no MIDI cable and no HOST check connector*) , these checks can be skipped)
1 Press "JAZZ" button to enter "MIDI/HOST check". DP1: MIDI Test
DP2: OK
2 Press the "COMPUTER" select. (* Position of HOST SW is at PC-1.)
3 Press the "JAZZ" button. DP1: Host PC98
DP2: OK
4 Press the "COMPUTER" select. (* Position of HOST SW is at PC-2.)
5 Press the "JAZZ" button. DP1: Host DOSV
DP2: OK
*) HOST check connector: short 2-3 pin of the connector with 1K ohm resistor.
Page-3
Message on LCD
7. LCD check
1 Press the "DANCE" button to enter "LCD check". DP1: LCD Test
2 Press the "EXECUTE" button.
* Test pattern 1 appears on the LCD, as well as there is no lacking dot.
3 Press the "EXECUTE" button.
* Test pattern 2 appears on the LCD, as well as there is no lacking dot.
4 Press the "EXECUTE" button.
* Test pattern 3 appears on the LCD, as well as there is no lacking dot.
5 Press the "EXECUTE" button.
* Test pattern 4 appears on the LCD, as well as there is no lacking dot.
6 Press the "EXECUTE" button.
* Test pattern 5 appears on the LCD, as well as there is no lacking dot.
7 Press the "EXIT" button. DP1: Test1
8. LED check
1 Press the "JAZZ" button to enter "LED check". DP1: LED TEST
* ALL LEDs are lit.