Professional Documents
Culture Documents
Sony - Uwp c1 c2 s1 s2 x1 x2 - Wireless - Microphone
Sony - Uwp c1 c2 s1 s2 x1 x2 - Wireless - Microphone
UWP-C1
UWP-C2
UWP-S1
UWP-S2
UWP-X1
UWP-X2
UHF SYNTHESIZED TRANSMITTER UHF SYNTHESIZED WIRELESS
UTX-B1 MICROPHONE
UTX-H1
UHF SYNTHESIZED DIVERSITY TUNER
URX-P1 UHF SYNTHESIZED DIVERSITY TUNER
URX-R1
UHF SYNTHESIZED TUNER UNIT
URX-M1
SERVICE MANUAL
1st Edition
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
UWP Series
Table of Contents
1. Service Overview
2. Electrical Alignment
UWP Series 1
2-5. URX-R1 .................................................................................................... 2-57
2-5-1. Equipment and Tools ............................................................... 2-57
2-5-2. Adjustments .............................................................................. 2-58
3. Spare Parts
2 UWP Series
6. Board Layouts
7. Schematic Diagrams
UWP Series 3
Section 1
Service Overview
1-1. UTX-B1
1-1-1. Disassembly
Six screws
BTP1.7 x 9
Lock (R)
Lock (L)
Battery cover
Unsolder.
Antenna
Front cabinet sub assembly (TX)
Nut
MB-4 board
Unsolder.
When reassembling the UTX-B1, insert the unit into the hole of the front cabinet while the battery springs
(_) are being compressed as shown.
Two holes
Hole
When the EEPROM (IC401) is replaced with the new EEPROM, the same data that have been stored in
the removed EEPROM must be written into the newly mounted EEPROM.
When an error occurs, any of the following error messages can be generated by the self-diagnostics
function that is built-in the UTX-B1 and can appear on the display section.
Err01 An error occurs in the backup Check the EEPROM (IC401) and its peripheral
memory data. circuits.
Err02 An error occurs in the PLL Check the PLL synthesizer circuit (IC102, CP101 on
synthesizer circuit. the MB-4 board and its peripheral circuits).
Err03 Power supply voltage has exceeded Use the equipment with the power supply of the
the range of allowable limits. specified voltage range.
1-2-1. Disassembly
Model cover
Ring stopper
Dynamic unit
Push up the claws.
*Grip removal fixture (If difficult to remove,
unlock one claw
Do not touch the portion after another.)
during removing the unit. * : Tools required :
Grip removal fixture (J-6407-080-A)
Connector (3P)
Go to page 1-5
(Grip A)
Dynamic unit
Remove it using
tweezers. Connector (3P)
Indicator
Precision
P2.6 x 5
Power button
Power lock
Stopper
Antenna
Stopper
Chassis (A)
assembly
Precision
P2 x 3
Protruded portion
of the indicator
Precision
Precision P2 x 3
P2 x 3
*LRT screw
MB-5 board
(M2 x 4)
Hole Shield
Unsolder.
Remove the chassis (A) Unsolder.
assembly in the direction of
the arrow in the way as if Three claws
removing the protruded
*LRT screw
portion of the indicator.
(M2 x 4)
Grip (A)
* : Tools required :
LRT screwdriver (J-6402-350-A)
Three claws
When install the Grip (A), install the Grip (A) under the state that the power is turned on and the protrud-
ed portion of the indicator is confirmed that it has fitted into the hole of the Grip (A) as shown.
ON
Hole
Power switch
Protruded portion
of the indicator
Grip (A)
When the EEPROM (IC401) is replaced with the new EEPROM, the same data that have been stored in
the removed EEPROM must be written into the newly mounted EEPROM.
When an error occurs, any of the following error messages can be generated by the self-diagnostics
function that is built-in the UTX-H1 and can appear on the display section.
Err01 An error occurs in the backup Check the EEPROM (IC401) and its peripheral
memory data. circuits.
Err02 An error occurs in the PLL Check the PLL synthesizer circuit (IC102, CP101 on
synthesizer circuit. the MB-5 board and its peripheral circuits).
Err03 Power supply voltage has exceeded Use the equipment with the power supply of the
the range of allowable limits. specified voltage range.
ECT
LINE 4 SEL
BATT
E AF
AF
BATT
panel of the URX-M1 or into the slot on the unit into URX-M1
which the URX-M1 will be installed.
. Keep the URX-M1 away from static electricity.
Removal
1. On the bottom panel of the MB-806A, locate the lever
corresponding to the slot of the URX-M1 to be Installation
removed and pull the lever forward. The URX-M1 is The SRP-X700P Powered Mixer can accommodate up to 2
ejected from the slot. URX-M1.
URX-M1 SCENE
RECALL
B
A MASTER
ECT
LINE 4 SEL
A
E
BATT
AF
GP
RF
F
CH
GP
Installation
The MB-806A Tuner Base Unit can accommodate up to 6
URX-M1.
The following procedures describe how to prove URX-M1 whether it needs to be required or not.
When an error occurs, any of the following error messages can be generated by the self-diagnostics
function that is built-in the URX-M1 and can appear on the display section.
Message Error contents Remedial measure
Err01 An error occurs in EEPROM data. Take both of the following remedial measures.
. Write the frequency data that corresponds to the
desired destination location, into EEPROM.
. Perform the RF squelch adjustment and the RF
level indicator adjustment. (Refer to Section 2-3.)
Err02 The PLL synthesizer circuit does not If the frequency data that does not corresponds to
lock. the desired reception frequency range is written:
Write the correct frequency data into the EEPROM.
If the error message is displayed even though the
frequency data is correct:
Check the PLL synthesizer circuit (IC302, CP301,
Q302 and Q303 and its peripheral circuits on the
MB-2 board).
Err03 Power supply voltage has exceeded Use the equipment with the power supply of the
the range of allowable limits. specified voltage range.
NOTONE The tone signal does not exist, or An interference radio wave has occurred in the
any tone signal radio wave other frequency band in use.
than 32 kHz is received and the . If an error is displayed while the power of the
audio signal is muted. transmitter is on:
Turn off the power of the transmitter.
. If the RF level indicator of the receiver LCD lights
even when the power of the transmitter is turned off:
Set the frequency of the transmit/receive channel
that is free from the interference radio wave.
When the error is not caused by the signal interfer-
ence, the tone squelch circuit of receiver or transmitter
(both receiver and transmitter) is defective.
. Check the receiver : Check the tone squelch.
(Refer to Section 2-3.)
If the tone squelch does
not work well, check the
tone squelch circuit (IC405
and its peripheral circuit
on the MB-2 board.)
. Check the transmitter : Refer to the Service
Manual of transmitter.
Sq OFF If you turn on the power while Turn off the power once and then back on without
pressing the “SET” button and the pressing any button.
“_” button at the same time, the
squelch function release mode is
set, and this message appears once
before the display of normal
operation appears.
1-4-1. Disassembly
Six screws
BTP1.7 x 9
Lock (R)
Rear cabinet
Lock (L)
Battery cover
Unsolder.
Connector (CN1)
Unsolder.
Two holes
Supplied
washer
Two stereo
Hole miniature jacks Jack
bracket
Power button
B1.7 x 5
*Gasket
Battery
spring (_)
*Gasket
MB-1 board
Unsolder.
* Refer to “1-4-4. Precaution when Replacing Gasket”.
When reassembling the URX-P1, insert the unit into the hole of the front cabinet while the battery springs
(_) are being compressed as shown.
Two holes
Hole
When the EEPROM (IC11) is replaced with the new EEPROM, the same data that have been stored in the
removed EEPROM must be written into the newly mounted EEPROM.
When replacing the gasket, separate the new gasket (3-207-026-01) into two blocks and use it.
Several absorption sheets are attached to the MB-1 board of the URX-P1 (CE62/CE67 model). When
replacing parts, replace the parts after peeling off the absorption sheet.
When replacement of the parts is completed, be sure to attach the absorption sheet that has been peeled off.
MB-1 board
When an error occurs, any of the following error messages can be generated by the self-diagnostics
function that is built-in the URX-P1 and can appear on the display section.
Message Error contents Remedial measure
Err01 An error occurs in EEPROM data. Take both of the following remedial measures.
. Write the frequency data that corresponds to the desired destination
location, into EEPROM.
. Perform the RF squelch adjustment and the RF level indicator
adjustment. (Refer to Section 2-4.)
Err02 The PLL synthesizer circuit does not If the frequency data that does not corresponds to the desired reception
lock. frequency range is written:
Write the correct frequency data into the EEPROM.
If the error message is displayed even though the frequency data is
correct:
Check the PLL synthesizer circuit (IC302, CP301, Q302 and Q303 and
its peripheral circuits on the MB-1 board).
Err03 Power supply voltage has exceeded Use the equipment with the power supply of the specified voltage range.
the range of allowable limits.
NOTONE The tone signal does not exist, or An interference radio wave has occurred in the frequency band in use.
any tone signal radio wave other . If an error is displayed while the power of the transmitter is on:
than 32 kHz is received and the Turn off the power of the transmitter.
audio signal is muted. . If the RF level indicator of the receiver LCD lights even when the power
of the transmitter is turned off:
Set the frequency of the transmit/receive channel that is free from
the interference radio wave.
When the error is not caused by the signal interference, the tone squelch
circuit of receiver or transmitter (both receiver and transmitter) is defective.
. Check the receiver : Check the tone squelch. (Refer to Section 2-4.)
If the tone squelch does not work well, check
the tone squelch circuit (IC405 and its
peripheral circuit on the MB-1 board.)
. Check the transmitter : Refer to the Service Manual of transmitter.
Sq OFF If you turn on the power while Turn off the power once and then back on without pressing any button.
pressing the “SET” button and the
“_” button at the same time, the
squelch function release mode is
set, and this message appears once
before the display of normal
operation appears.
UWP Series 1-11
1-5. URX-R1
MB-3
DP-2
JK-1
If the antenna harness is removed during removal of circuit boards (or parts), route the antenna harness as
shown below.
When an error occurs, any of the following error messages can be generated by the self-diagnostics
function that is built-in the URX-R1 and can appear on the display section.
Message Error contents Remedial measure
Err01 An error occurs in EEPROM data. Take both of the following remedial measures.
. Write the frequency data that corresponds to the
desired destination location, into EEPROM.
. Perform the RF squelch adjustment and the RF
level indicator adjustment. (Refer to Section 2-5.)
Err02 The PLL synthesizer circuit does not If the frequency data that does not corresponds to
lock. the desired reception frequency range is written:
Write the correct frequency data into the EEPROM.
If the error message is displayed even though the
frequency data is correct:
Check the PLL synthesizer circuit (IC302, CP301,
Q302 and Q303 and its peripheral circuits on the
MB-3 board).
Err03 Power supply voltage has exceeded Use the equipment with the power supply of the
the range of allowable limits. specified voltage range.
NOTONE The tone signal does not exist, or An interference radio wave has occurred in the
any tone signal radio wave other frequency band in use.
than 32 kHz is received and the . If an error is displayed while the power of the
audio signal is muted. transmitter is on:
Turn off the power of the transmitter.
. If the RF level indicator of the receiver LCD lights
even when the power of the transmitter is turned off:
Set the frequency of the transmit/receive channel
that is free from the interference radio wave.
When the error is not caused by the signal interfer-
ence, the tone squelch circuit of receiver or transmitter
(both receiver and transmitter) is defective.
. Check the receiver : Check the tone squelch.
(Refer to Section 2-5.)
If the tone squelch does
not work well, check the
tone squelch circuit (IC405
and its peripheral circuit
on the MB-3 board.)
. Check the transmitter : Refer to the Service
Manual of transmitter.
Sq OFF If you turn on the power while Turn off the power once and then back on without
pressing the “SET” button and the pressing any button.
“_” button at the same time, the
squelch function release mode is
set, and this message appears once
before the display of normal
operation appears.
2-1. UTX-B1
Equipment Required
Tool
↓ Solder here.
4. Reference Frequency Deviation Adjustment Solder here.
↓ MB-4 board (B side)
5. Maximum Frequency Deviation Adjustment Check
↓ After the DC power supply connection is complete, set the
6. Distortion Ratio Check power switch (S301) to ON, and check the level on DC
↓ ammeter.
7. S/N Check DC ammeter indication level: 130 to 200 mA
↓
8. Frequency Characteristics Check
4. Switch and Control Initial Setting
↓
MB-4 board
9. Tone Signal Adjustment
Switch and Control Setting
↓
10. Spurious Emissions Check U6264 model ; 62-01 channel (758.125 MHz)
↓ U6668 model ; 66-01 channel (782.125 MHz)
11. Ocupied Band Width Check CE62 model ; Group 00, 62-01 channel (798.125 MHz)
CE67 model ; Group 00, 67-01 channel (838.125 MHz)
Preparation AU model ; 66-01 channel (792.250 MHz)
1. When adjustments are performed, remove the MB-4 CN model ; 62-01 channel (758.125 MHz)
board from UTX-B1 unit. KR model ; 59-01 channel (740.125 MHz)
(Refer to the Section 1-1-1. for removal.) Attenuation setting : 0 dB
2. Connect the SMA-BNC conversion connector (J-6402- Accumulated time setting : “00 : 00”
480-A) and the MM-SMA conversion connector (J- n
6402-490-A) to the antenna terminal (CN101) on the Note down the setting position before the adjustment.
MB-4 board as shown below. After the Adjustment complete, set the original position.
CT401
MM-SMA conversion connector (Transmitter frequency)
CT101
(Transmitter output)
OFF ON
RV1 (Max.
frequency deviation)
S301
Connections
(For connecting the DC power supply, refer to step
“3. Connecting the DC power supply” in Section 2-1-2.)
S301
C212
C211
GND
+_
DC voltmeter
Connections
(For connecting the DC power supply, refer to step
“3. Connecting the DC power supply” in Section 2-1-2.)
CN101
MB-4 board
(B side)
Frequency counter
Connections
(For connecting the DC power supply, refer to step
“3. Connecting the DC power supply” in Section 2-1-2.)
CN101
MB-4 board
(B side)
Power sensor
Power meter
BNC connector
Switch and Control Setting HOT
MB-4 board
Transmission channel
U6264 model ; 64-01 channel (770.125 MHz)
CN2
U6668 model ; 68-01 channel (794.125 MHz)
CE62 model ; Group 00, 63-32 channel (810.000 MHz)
MB-4 board
CE67 model ; Group 00, 68-32 channel (850.000 MHz) (A side)
AU model ; 67-01 channel (799.250 MHz)
CN model ; 64-01 channel (770.125 MHz)
Audio analyzer Level meter
KR model ; 60-01 channel (746.125 MHz)
Oscillator
Attenuation setting : 0 dB
Accumulated time setting : “00 : 00”
n
Note down the setting position before the adjustment.
After the Adjustment complete, set the original position. Procedure
1. Input 1 kHz, _60 dBV (_57.8 dBm) signal to the MIC
INPUT connector (with Mic input cable).
(0 dBV = 1 Vrms)
2. Connect a modulation analyzer to the antenna terminal
(CN101) via the MM-SMA conversion connector and
the SMA-BNC conversion connector.
3. Adjust 1RV101 so that the frequency deviation for the
modulation analyzer reading meets the following speci-
fication.
Specification : Frequency deviation = ±5 kHz ±0.1 kHz
Adjustment : 1RV101/MB-4 board (A side)
(Refer to page 2-2 for the adjustment location.)
Connections Connections
(For connecting the DC power supply, refer to step (For connecting the DC power supply, refer to step
“3. Connecting the DC power supply” in Section 2-1-2.) “3. Connecting the DC power supply” in Section 2-1-2.)
CN101 CN101
MB-4 board MB-4 board
(B side) (B side)
Modulation Frequency
analyzer counter
RF IN AF UOT
Spectrum analyzer
Procedure Procedure
1. Connect the spectrum analyzer to the antenna terminal n
(CN101) via the MM-SMA conversion connector and Perform the checking with the MIC INPUT connector short-
the SMA-BNC conversion connector. circuit.
2. Set the spectrum analyzer as below:
CENTER FREQUENCY (fc) 1. Set the modulation analyzer as below:
U6264 model : 770.125 MHz MEASUREMENT : FM
U6668 model : 794.125 MHz MEASUREMENT RANGE : ±40 kHz
CE62 model : 810.000 MHz
HPF : 4 kHz
CE67 model : 850.000 MHz
LPF : >20 kHz
AU model : 799.250 MHz
DE EMPHASIS : OFF
CN model : 770.125 MHz
2. Check that the frequency counter (resolution : 0.1 Hz
KR model ; 746.125 MHz
setting) reading is 32.000 kHz ±1Hz.
REFERENCE LEVEL : 20 dBm
FREQUENCY SPAN : 200kHz (20 kHz/DIV)
RBW (resolution band width) : 3kHz
VBW (video band width) : 1kHz
ATT : 20 dB
3. Adjust 1RV103/MB-4 board (A side) so that level
between carrier frequency (frequency center level) on
spectrum analyzer and tone signal is within 29 dB ±1 dB.
20 dBm
29±1 dB
v:10 dB/div
H:20 MHz/div
fc
32.000 kHz
2-10 UWP Series
10. Spurious Emissions Check Connections
. For connecting the DC power supply, refer to step
Equipment and Tools “3. Connecting the DC power supply” in Section 2-1-2.
. DC power supply . For connecting the MIC input connector (CN1), refer to
DC output voltage : +3.0 ±0.1Vdc “4.Reference Frequency Deviation Adjustment”.
. DC ammeter
. Spectrum analyzer
. MM-SMA conversion connector
(SONY Part No. J-6402-490-A)
. SMA-BNC conversion connector CN101
(SONY Part No. J-6402-480-A) MB-4 board
(B side)
_40 dBm
v:10 dB/div
H:20 MHz/div
1.5 GHz (fc) 3 GHz
carrier frequency
with no input signal
REFERENCE LEVEL
_23 dB
v:10 dB/div
H:50 kHz/div
fc
band width
80 kHz or less
Equipment Required
Tool
↓ Solder here.
5. Maximum Frequency Deviation Adjustment MB-5 board (B side)
↓
6. Distortion Ratio Check Check
↓ After the DC power supply connection is complete, set the
7. S/N Check power switch (S301) to ON, and check the level on DC
↓ ammeter.
8. Frequency Characteristics Check DC ammeter indication level: 130 to 200 mA
↓
9. Tone Signal Adjustment 4. Switch and Control Initial Setting
↓ MB-5 board
10. Spurious Emissions Check Switch and Control Setting
↓ U6264 model ; 62-01 channel (758.125 MHz)
11. Ocupied Band Width Check U6668 model ; 66-01 channel (782.125 MHz)
CE62 model ; Group 00, 62-01 channel (798.125 MHz)
CE67 model ; Group 00, 67-01 channel (838.125 MHz)
Preparation
AU model ; 66-01 channel (792.250 MHz)
1. When adjustments are performed, remove the MB-5
board from UTX-H1 unit. CN model ; 62-01 channel (758.125 MHz)
(Refer to the Section 1-2-1. for removal.) KR model ; 59-01 channel (740.125 MHz)
Attenuation setting : 0 dB
2. Connect the SMA-BNC conversion connector (J-6402-
Accumulated time setting : “00 : 00”
480-A) and the MM-SMA conversion connector (J-
n
6402-490-A) to the antenna terminal (CN101) on the
Note down the setting position before the adjustment.
MB-5 board as shown below.
After the Adjustment complete, set the original position.
GND
C211
C212
OFF
S301
ON
Procedure
1. Set the POWER switch (S301) on the MB-5 board to ON.
2. Check the DC Voltage of the + terminal on the C212 to
the specified voltage as below :
Specification : + terminal DC Voltage = +3.3 ± 0.1Vdc
3. Check the DC voltage of the + terminal on the C211 to
the specified voltage as below :
Specification : + terminal DC voltage= +5.0 ± 0.1Vdc
Connections
(For connecting the DC power supply, refer to step
“3. Connecting the DC power supply” in Section 2-2-2.)
Frequency counter
CN101
Connections
(For connecting the DC power supply, refer to step
“3. Connecting the DC power supply” in Section 2-2-2.)
CN101
Power sensor
Connections Connections
(For connecting the DC power supply, refer to step (For connecting the DC power supply, refer to step
“3. Connecting the DC power supply” in Section 2-2-2.) “3. Connecting the DC power supply” in Section 2-2-2.)
Spectrum analyzer
Modulation Frequency
analyzer counter
RF IN AF UOT
Procedure
1. Connect the spectrum analyzer to the antenna terminal Procedure
(CN101) via the MM-SMA conversion connector and n
the SMA-BNC conversion connector. Perform the checking with the MIC INPUT connector short-
2. Set the spectrum analyzer as below: circuit.
CENTER FREQUENCY (fc)
U6264 model : 770.125 MHz 1. Set the modulation analyzer as below:
U6668 model : 794.125 MHz MEASUREMENT : FM
CE62 model : 810.000 MHz MEASUREMENT RANGE : ±40 kHz
CE67 model : 850.000 MHz HPF : 4 kHz
AU model : 799.250 MHz LPF : >20 kHz
CN model : 770.125 MHz DE EMPHASIS : OFF
KR model ; 746.125 MHz 2. Check that the frequency counter (resolution : 0.1 Hz
REFERENCE LEVEL : 20 dBm
setting) reading is 32.000 kHz ±1Hz.
FREQUENCY SPAN : 200kHz (20 kHz/DIV)
RBW (resolution band width) : 3kHz
VBW (video band width) : 1kHz
ATT : 20 dB
3. Adjust 1RV103/MB-5 board (A side) so that level
between carrier frequency (frequency center level) on
spectrum analyzer and tone signal is within 29 dB ±1 dB.
20 dBm
29±1 dB
v:10 dB/div
H:20 MHz/div
fc
32.000 kHz
UWP Series 2-23
10. Spurious Emissions Check Connections
. For connecting the DC power supply, refer to step
Equipment and Tools “3. Connecting the DC power supply” in Section 2-2-2.
. DC power supply . For connecting the MIC input connector (CN2), refer to
DC output voltage : +3.0 ±0.1Vdc “4.Reference Frequency Deviation Adjustment”.
. DC ammeter
. Spectrum analyzer
. MM-SMA conversion connector Spectrum analyzer
(SONY Part No. J-6402-490-A)
. SMA-BNC conversion connector
(SONY Part No. J-6402-480-A)
_37 dBm
v:10 dB/div
H:20 MHz/div
1.5 GHz (fc) 3 GHz
_23 dB
v:10 dB/div
H:50 kHz/div
fc
band width
80 kHz or less
Equipment
Tools
Ceramic capacitor
BNC-J connector 0.001 uF 50 V (1-161-456-00) BNC-P connector
(1-562-261-21) (1-560-257-11)
Cut Plated wire (0.6 to 0.8 ø)
3 mm
2 mm Solder
U6264 U62
U6668 U66
CE62 CE62
CE67 CE67
AU AU66
Frequency counter
MB-2 board (B side)
Procedure
1. Connect the frequency counter to the IC13 (pin No.4)/
MB-2 board (A side).
2. Adjustmemt
Specification : :Frequency at IC13 (pin No.4)/MB-2
board (A side) = 4.000 MHz ± 20 Hz
Adjustment : 1 CT11/MB-2 board (A side)
n
The adjustment procedures describe that the URX-M1
(to be adjusted) is installed into the Tuner [1] slot on the
MB-806A MB-806A.
1 2 3 4 5 6 1. Connect the audio analyzer to the TUNER OUTPUT 1
Tuner slot
connector via MIC amp.
2. Connect the signal generator to the ANTENNA A IN
connector with DC cut fixture.
3. Adjustment (ANTENNA A IN side adjustment)
Point : TUNER OUTPUT 1
RV201 RV101
Specification : Output level (level meter indication
level) = _20 dBm ±0.5 dB (at 600 Z
loaded)
URX-M1
Adjustment : 1RV201/MB-2 board (URX-M1)
4. Connect the signal generator to the ANTENNA B IN
connector with DC cut fixture.
Connection
Signal
generator
ANTENNA A IN ANTENNA B IN
MB-806A
1 2 3 4 5 6
Tuner slot
U62 Procedure
(1) Output Level Check
(U62) ↓
(2) S/N Check
. U6668 model ↓
(3) Frequency Characteristic Check
U68 ↓
(4) Distortion Ration Check
(U68) ↓
. CE62 model (5) RF Squelch Level/RF Indicator Check
↓
Connection
Audio
MIC amp analyzer
600 Z
balance
Signal input
generator TUNER
OUTPUT 1
Function
generator
MB-806A
1 2 3 4 5 6
Tuner slot
Procedure Procedure
n n
The checking procedures describe that the URX-M1 (to be The checking procedures describe that the URX-M1 (to be
adjusted) is installed into the Tuner [1] slot on the MB-806A. adjusted) is installed into the Tuner [1] slot on the MB-806A.
RF indicator lights.
Lighting
LCD : 35 dBuVEMF ±5 dB
Lighting
LCD :
45 dBuVEMF ±5 dB
Lighting
LCD :
55 dBuVEMF ±5 dB
Lighting
Procedure Procedure
n n
The checking procedures describe that the URX-M1 (to be The checking procedures describe that the URX-M1 (to be
adjusted) is installed into the Tuner [1] slot on the MB-806A. adjusted) is installed into the Tuner [1] slot on the MB-806A.
Equipment
Tools Required
Name Part No. Remarks
. Wiring diagram
3-pole mini Phone plug (Ø3.5) XLR, 3P connector (male)
Chip
2 1 1 ; GND
2 ; HOT
3
3 ; COLD
—Wiring side— —Wiring side—
Ring
Sleeve
IC13
Pin No.4
MB-1 board
Battery spring (A side)
DC power supply
(DC output voltage :
+3.0 ± 0.1 V) Frequency counter
Battery terminal (+)
Procedure
+ _
1. Connect the frequency counter to the IC13 (pin No.4)/
DC ammeter MB-1 board (A side).
2. Adjustmemt
+ _
Specification : :Frequency at IC13 (pin No.4)/MB-1
board (A side) = 4.000 MHz ± 20 Hz
Adjustment : 1 CT11/MB-1 board (A side)
Connection
. Same as “3.Output Level Adjustment”.
. For connecting the DC power supply, refer to “1.
Current Consumption Check”.
U62 Procedure
(U62) (1) Output Level Check
↓
. U6668 model (2) S/N Check
↓
CE62 ↓
(6) RF Level Indicator Check
(CE62) ↓
. CE67 model (7) AF Level Indicator/AF Indicator Check
↓
CE67 (8) Tone Squelch Check
↓
(CE67) (9) Monitor Level Check
. AU66 model
Because the audio system of the URX-P1 is output in the 1. Reassembly URX-P1 completely.
unbalanced system, the noise level can be possibly so high 2. Turn on the power of the URX-P1 following the
that the S/N measurement becomes impossible depending procedure. (For setting, refer to “Setting the Squelch
on the measurement system. In such a case, reassemble the OFF mode” on page 2-42. For the power supply, use
URX-P1 completely and emit the RF output of the signal the battery.)
3. Set the signal generator output level to 80 dBu. (Set
generator from the antenna (Part No.1-501-612-13) and
the measurement frequency and other parameters to
receive the RF signal with the URX-P1 in order to
the same setup as the ordinary measurement.)
implement the S/N ratio measurement.
4. Move the antenna connected to the signal generator, in
the periphery of the antenna a of the URX-P1 as
Equipment and Tools shown in the illustration.
. Signal generator
. Audio analyzer Antenna
Antenna “a”
Oscilloscope
URX-P1
Procedure Procedure
RF indicator lights.
Lighting
LCD : 35 dBuVEMF ±5 dB
Lighting
LCD : 45 dBuVEMF ±5 dB
Lighting
Procedure Procedure
Connection Level meter How to make Stereo mini-plug with load resisters
GND Equipment
. Stereo mini-plug with cable (diameter : 3.5 mm)
(Sony RK-G136 (accessory), or equivalent) : 1
. Resister, carbon 16Z 1/4W (Part No. 1-247-088-00) : 2
Stereo mini-plug n
with load resister To use the cable RK-G136, cut it into an appropriate
Signal generator
length to use it.
RF
adjusting Solder here.
Make it as short cable Solder here.
as possible.
Shielded wire
16Z 1/4W
MM-SMA conversion CN101 carbon resisters
connector
Solder here.
RF adjusting
cable
Stereo mini-plug with cord
(3.5mm diameter)
OUTPUT CN201
MONITOR
MM-SMA MB-1
conversion board
connector
RV201
RV101
CN101 or CN201
Equipment
Tools Required
Name Part No. Remarks
. Wiring diagram
3-pole mini Phone plug (Ø3.5) XLR, 3P connector (male)
Chip
2 1 1 ; GND
2 ; HOT
3
3 ; COLD
—Wiring side— —Wiring side—
Ring
Sleeve
MB-3 board
CT11
CN201 IC13 CN101
Solder
Procedure
MB-3 board 1. Connect the frequency counter to the IC13 (pin No.4)/
MB-3 board (A side).
2. Adjustmemt
Specification : Frequency at IC13 (pin No.4)/MB-3
board (A side) = 4.000 MHz ± 20 Hz
Adjustment : 1 CT11/MB-3 board (A side)
Procedure
-SOL-
Preparation (-SQL- )
A C3 L generator as follows :
FREQUENCY (carrier frequency) :
(A C3 L) U6264 model/CN model ; 777.000 MHz
U6668 model ; 794.000 MHz
CE62 model ; 810.000 MHz
CE67 model ; 850.000 MHz
AU model ; 794.000 MHz
KR model ; 746.000 MHz
22. Check first that indication “L” of “BC2L” on the LCD
has disappeared, and then press the “SET” button.
2-62 UWP Series
23. Indication on the LCD (URX-P1) appears as follows : 5. Overall Characteristics Check
LCD :
Perform the overall characteristics check according to the
B C3 L following procedure.
(B C3 L) Procedure
(1) Output Level Check
24. Set the FREQUENCY (carrier frequency) of the signal
generator as follows : ↓
FREQUENCY (carrier frequency) : (2) S/N Check
U6264 model/CN model ; 781.000 MHz ↓
U6668 model ; 805.000 MHz (3) Frequency Characteristic Check
CE62 model ; 821.000 MHz ↓
CE67 model ; 861.000 MHz (4) Distortion Ration Check
AU model ; 805.000 MHz ↓
KR model ; 751.000 MHz (5) RF Squelch Level/RF Indicator Check
25. Check first that indication “L” of “BC3L” on the LCD ↓
has disappeared, and then press the “SET” button. (6) RF Level Indicator Check
26. Indication on the LCD appears as follows :
↓
LCD :
(7) AF Level Indicator/AF Indicator Check
. U6264 model/CN model
↓
(8) Tone Squelch Check
U62 ↓
(9) Monitor Level Check
(U62)
(CE67)
. AU66 model
AU66
(AU66)
. KR model
HELLO
(HELLO)
Procedure Procedure
AF
RF
RF indicator lights.
Lighting
LCD : 45 dBuVEMF ±5 dB
Lighting
LCD : 55 dBuVEMF ±5 dB
Lighting
Procedure Procedure
Equipment
TUNER OUTPUT
(balanced) . AF output cable (part No. 1-792-249-11) : 1
. Resister, carbon 16Z 1/4W (Part No. 1-247-088-00) : 2
n
To use the AF output cable, cut it into an appropriate
MB-3 board
length to use it.
RV201 RV101 Solder here.
Signal
Solder here.
generator
AF output cable
RF adjusting MONITOR connector
cable
3.5mm stereo jack to 1/4"
stereo phone plug adaptor
2. Standardization of Parts
Some repair parts supplied by Sony differ from those
used for the unit. These are because of parts common-
ality and improvement.
Parts list has the present standardized repair parts.
3. Stock of Parts
Parts marked with “o” at SP (Supply Code) column of
the spare parts list may not be stocked. Therefore, the
delivery date will be delayed.
4. Harness
Harnesses with no part number are not registered as
spare parts.
In need of repair, get components shown in the list and
repair using them.
5. Destination Representation
The part indicated “For U/CE/AU/CN” in the spare
parts list is used in the unit written below.
For U: The part is used in a unit for the U.S.A. and
Canada.
For CE: The part is used in a unit for the European.
For AU: The part is used in a unit for the Austraria.
For CN: The part is used in a unit for the China.
For KR: The part is used in a unit for the Korea.
3-2-1. UTX-B1
6
19
19
22 20
15
2 11
12
22
15
4
13
14
18
22
16
10
21
21
21
17
3-2-2. UTX-H1 a
18
16
13
15 18
19
4
3
PRECISION
PRECISION
P2.6 x 5
P2 x 3
17
PRECISION
P2 x 3
PRECISION
12 P2 x 3
10
2
11
14
3-2-3. URX-M1
11
10
6 10
9
4
2
5
3
7
3-2-4. URX-P1
19
6
19
21
23
3
14
2
10
11
14
23 4
12
17
13 15
23
* 20
*
20
9
18
22
22
16
22
* : When the GASKET (SMC) 3-207-026-01 is supplied as the repair part, size is
the double of what is required. So, cut it into half before use.
3-2-5. URX-R1
BTP3 x 8
15
BTP3 x 8
B3 x 6 a
BVTP3 x 8
14
6 3
9 d
5
10 16
BVTP3 x 8
BVTP BVTP3 x 8
8
3x8
b
7
4 1
BVTP
3x8
BVTP3 x 8
11
BVTP3 x 8 d
2
12
BTP3 x 8
c b
BTP3 x 8
BTP3 x 8
BTP3 x 8
13 c 13
3-3-1. UTX-B1
----------
MB-4 BOARD (MB-4 BOARD)
----------
Ref. No. Ref. No.
or Q’ty Part No. SP Description or Q’ty Part No. SP Description
1pc A-4591-446-A s MOUNTED CIRCUIT BOARD, MB-4 C104 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V
(For U6264 model/CN model) C105 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V
A-4591-460-A s MOUNTED CIRCUIT BOARD, MB-4 C106 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V
(For U6668 model/AU model) C107 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V
A-4591-472-A s MOUNTED CIRCUIT BOARD, MB-4 C108 1-107-689-21 s CAPACITOR,TANTALUM 1MF/35V
(For CE62 model)
A-4591-484-A s MOUNTED CIRCUIT BOARD, MB-4 C109 1-164-874-11 s CAPACITOR,CHIP CERAMIC 100PF
(For CE67 model) C110 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF
A-4591-518-A s MOUNTED CIRCUIT BOARD, MB-4 C111 1-164-874-11 s CAPACITOR,CHIP CERAMIC 100PF
(For KR model) C112 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF
C113 1-164-874-11 s CAPACITOR,CHIP CERAMIC 100PF
1pc 1-467-301-11 s DISPLAY, LIQUID CRYSTAL
2pcs 2-347-672-01 s PLATE , BATTERY (+) C114 1-164-874-11 s CAPACITOR,CHIP CERAMIC 100PF
C115 1-164-937-11 s CAPACITOR,CHIP CERAMIC 1000PF
C2 1-104-852-11 s CAPACITOR,TANTALUM 22MF/10V C116 1-164-858-11 s CAPACITOR,CERAMIC 22PF/16V
C3 1-164-937-11 s CAPACITOR,CHIP CERAMIC 1000PF C117 1-164-858-11 s CAPACITOR,CERAMIC 22PF/16V
C4 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V C118 1-119-923-11 s CAPACITOR,CHIP CERAMIC 0.047MF
C5 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF
C6 1-104-915-11 s CAPACITOR,CHIP 2.2MF/20V C119 1-104-852-11 s CAPACITOR,TANTALUM 22MF/10V
C120 1-164-949-11 s CAPACITOR,CHIP CERAMIC 0.047MF
C7 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C121 1-164-937-11 s CAPACITOR,CHIP CERAMIC 1000PF
C8 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V C122 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V
C9 1-104-915-11 s CAPACITOR,CHIP 2.2MF/20V C123 1-110-569-21 s CAPACITOR CHIP TANTAL47MF/6.3V
C11 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V
C12 1-164-934-11 s CAPACITOR CERAMIC 330PF/16V(B) C124 1-137-859-11 s CAPACITOR,TANTALUM 220MF 3528
C125 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF
C13 1-164-934-11 s CAPACITOR CERAMIC 330PF/16V(B) C126 1-110-569-21 s CAPACITOR CHIP TANTAL47MF/6.3V
C14 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V C127 1-164-866-11 s CAPACITOR,CHIP CERAMIC 47PF/16
C15 1-165-908-11 s CAP, CERAMIC 1000000PF B 1608 C128 1-164-937-11 s CAPACITOR,CHIP CERAMIC 1000PF
C16 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V
C17 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V C129 1-104-852-11 s CAPACITOR,TANTALUM 22MF/10V
C130 1-164-937-11 s CAPACITOR,CHIP CERAMIC 1000PF
C18 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V C131 1-164-858-11 s CAPACITOR,CERAMIC 22PF/16V
C19 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V C132 1-164-937-11 s CAPACITOR,CHIP CERAMIC 1000PF
C20 1-164-934-11 s CAPACITOR CERAMIC 330PF/16V(B) C133 1-164-842-11 s CAPACITOR CERAMIC 2PF/16V 1005
C21 1-104-915-11 s CAPACITOR,CHIP 2.2MF/20V
C22 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V C134 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V
C135 1-164-842-11 s CAPACITOR CERAMIC 2PF/16V 1005
C23 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V C136 1-164-937-11 s CAPACITOR,CHIP CERAMIC 1000PF
C24 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V C137 1-164-843-11 s CAPACITOR CHIP CERAMIC 3PF/16V
C25 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V C138 1-164-937-11 s CAPACITOR,CHIP CERAMIC 1000PF
C26 1-164-874-11 s CAPACITOR,CHIP CERAMIC 100PF
C27 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V C140 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V
C141 1-164-937-11 s CAPACITOR,CHIP CERAMIC 1000PF
C28 1-164-940-11 s CAPACITOR,CHIP CERAMIC 3300/16 C142 1-164-843-11 s CAPACITOR CHIP CERAMIC 3PF/16V
C29 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C143 1-164-843-11 s CAPACITOR CHIP CERAMIC 3PF/16V
C30 1-164-939-11 s CAPACITOR,CHIP CERAMIC 2200PF C201 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V
C31 1-164-936-11 s CAPACITOR,CHIP CERAMIC 680PF
C32 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V C202 1-135-856-11 s CAPACITOR,TANTALUM 100MF/10V
C203 1-135-856-11 s CAPACITOR,TANTALUM 100MF/10V
C33 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V C204 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V
C34 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C205 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V
C35 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V C206 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V
C36 1-107-689-21 s CAPACITOR,TANTALUM 1MF/35V
C37 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V C211 1-107-689-21 s CAPACITOR,TANTALUM 1MF/35V
C212 1-107-689-21 s CAPACITOR,TANTALUM 1MF/35V
C38 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V C301 1-135-856-11 s CAPACITOR,TANTALUM 100MF/10V
C39 1-164-933-11 s CAP CHIP CERAMIC 220PF/16V(B) C302 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V
C40 1-131-664-11 s CAP,CHIP CERAMIC 0.15MF B 1608 C303 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V
C41 1-135-210-11 s CAPACITOR,TANTALUM 4.7MF/10V
C42 1-164-939-11 s CAPACITOR,CHIP CERAMIC 2200PF C304 1-135-856-11 s CAPACITOR,TANTALUM 100MF/10V
C401 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V
C43 1-164-936-11 s CAPACITOR,CHIP CERAMIC 680PF C402 1-135-856-11 s CAPACITOR,TANTALUM 100MF/10V
C44 1-164-874-11 s CAPACITOR,CHIP CERAMIC 100PF C403 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF
C45 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V C404 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V
C46 1-164-858-11 s CAPACITOR,CERAMIC 22PF/16V
C101 1-164-858-11 s CAPACITOR,CERAMIC 22PF/16V C405 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V
C406 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF
C102 1-164-860-11 s CAPACITOR,CHIP CERAMIC 27PF/16 C408 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V
C103 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C409 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V
3-12 UWP Series
(MB-4 BOARD) (MB-4 BOARD)
Ref. No. Ref. No.
or Q’ty Part No. SP Description or Q’ty Part No. SP Description
C410 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V L1 1-414-398-11 s INDUCTOR (SMD) 10UH
C411 1-164-937-11 s CAPACITOR,CHIP CERAMIC 1000PF L101 1-414-783-21 s INDUCTOR, CHIP 5.6NH (1005)
C414 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF L102 1-469-860-21 s INDUCTOR, CHIP 39.0NH (1005)
C415 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF L103 1-414-783-21 s INDUCTOR, CHIP 5.6NH (1005)
C416 1-164-845-11 s CAPACITOR,CERAMIC 5PF/16V(1005 L105 1-410-658-31 s INDUCTOR,CHIP 220UH (3225)
C417 1-164-860-11 s CAPACITOR,CHIP CERAMIC 27PF/16 L106 1-410-658-31 s INDUCTOR,CHIP 220UH (3225)
C420 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V L108 1-414-783-21 s INDUCTOR, CHIP 5.6NH (1005)
C421 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF L109 1-414-783-21 s INDUCTOR, CHIP 5.6NH (1005)
C425 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF L110 1-414-788-21 s INDUCTOR, CHIP 15.0NH (1005)
L111 1-414-788-21 s INDUCTOR, CHIP 15.0NH (1005)
CN1 1-766-809-11 o PIN, CONNECTOR (PC BOARD) 3P
CN101 1-774-915-11 s CONNECTOR, COAXIAL L112 1-414-788-21 s INDUCTOR, CHIP 15.0NH (1005)
CP101 1-781-489-11 s OSCILLATOR (VOLTAGE VAR TYPE) L201 1-419-384-21 s COIL 47UH
(For U6264 model/CN model) L202 1-414-398-11 s INDUCTOR (SMD) 10UH
1-781-491-11 s OSCILLATOR (VOLTAGE VAR TYPE)
(For U6668 model/AU model) Q1 8-729-037-52 s TRANSISTOR 2SD2216J-QR(TX).SO
1-795-210-11 s OSCILLATOR (VOLTAGE VAR TYPE) Q3 8-729-037-52 s TRANSISTOR 2SD2216J-QR(TX).SO
(For CE62 model) Q4 8-729-425-50 s TRANSISTOR 2SB1462Q
1-781-493-11 s OSCILLATOR (VOLTAGE VAR TYPE) Q5 8-729-037-52 s TRANSISTOR 2SD2216J-QR(TX).SO
(For CE67 model) Q6 8-729-037-52 s TRANSISTOR 2SD2216J-QR(TX).SO
1-795-191-21 s OSCILLATOR (VOLTAGE VAR TYPE)
(For KR model) Q7 8-729-037-52 s TRANSISTOR 2SD2216J-QR(TX).SO
CP102 1-251-974-11 s ISOLATOR Q101 8-729-821-88 s TRANSISTOR 2SK1332-3
(For U6264 model/CN model) Q102 8-729-037-52 s TRANSISTOR 2SD2216J-QR(TX).SO
1-251-958-11 s ISOLATOR Q103 8-729-928-87 s TRANSISTOR DTC124EE
(For U6668 model/AU model) Q104 8-729-031-69 s TRANSISTOR 2SA1965-TL
1-251-830-11 s ISOLATOR
(For CE62 model) Q105 8-729-031-69 s TRANSISTOR 2SA1965-TL
1-251-831-11 s ISOLATOR Q106 8-729-039-32 s TRANSISTOR 2SC5015-T1
(For CE67 model) Q107 8-729-034-66 s TRANSISTOR 2SC4738-Y-TE85L
1-251-973-21 s ISOLATOR Q108 8-729-231-69 s TRANSISTOR 2SC3607-TE12L
(For KR model) Q201 8-729-052-37 s TRANSISTOR XP151A13A0MR
CT101 1-141-435-21 s CAPACITOR TRIMMER (CHIP TYPE) Q301 8-729-037-52 s TRANSISTOR 2SD2216J-QR(TX).SO
CT401 1-141-322-11 s CAPACITOR,VAR,TRIMMER Q302 8-729-039-86 s TRANSISTOR FMMT717TA
Q303 8-729-037-52 s TRANSISTOR 2SD2216J-QR(TX).SO
D1 8-719-421-69 s DIODE MA133 Q401 8-729-928-87 s TRANSISTOR DTC124EE
D2 8-719-988-61 s DIODE 1SS355TE-17
D3 8-719-421-69 s DIODE MA133 R1 1-218-959-11 s RESISTOR, CHIP 3.3K
D101 8-719-039-99 s DIODE UMZ8.2T R2 1-218-958-11 s RESISTOR,CHIP 2.7K 1/16W(1005)
D105 8-719-421-69 s DIODE MA133 R3 1-218-956-11 s RESISTOR, CHIP 1.8K
R4 1-218-955-11 s RESISTOR, CHIP 1.5K
D106 8-719-988-61 s DIODE 1SS355TE-17 R5 1-218-953-11 s RESISTOR, CHIP 1K 1/16W
D107 8-719-421-69 s DIODE MA133
D201 8-719-072-27 s DIODE MA2Z748001S0 R6 1-218-951-11 s RESISTOR, CHIP 680 1/16
D301 8-719-039-99 s DIODE UMZ8.2T R7 1-218-949-11 s RESISTOR,CHIP 470 1/16W
D401 8-719-064-07 s DIODE SML-310LTT86 R8 1-218-954-11 s RESISTOR, CHIP 1.2K 1/16W
R9 1-218-969-11 s RESISTOR,CHIP 22K 1/16W (1608)
D403 8-719-421-69 s DIODE MA133 R10 1-218-947-11 s RESISTOR, CHIP 330 1/16W
FL1 1-233-322-11 s FILTER, CHIP EMI R11 1-218-977-11 s RESISTOR,CHIP 100K 1/16W(1005)
FL2 1-233-322-11 s FILTER, CHIP EMI R12 1-218-977-11 s RESISTOR,CHIP 100K 1/16W(1005)
FL301 1-233-322-11 s FILTER, CHIP EMI R14 1-218-965-11 s RESISTOR, CHIP 10K 1/16W
R15 1-218-965-11 s RESISTOR, CHIP 10K 1/16W
IC1 8-759-523-00 s IC TC74HC4051AFT(EL) R18 1-218-965-11 s RESISTOR, CHIP 10K 1/16W
IC2 8-759-422-21 s IC NJM4580VTE2
IC3 8-759-710-82 s IC NJM2406F R19 1-218-965-11 s RESISTOR, CHIP 10K 1/16W
IC4 8-759-370-11 s IC NJM2100V-TE2 R20 1-218-965-11 s RESISTOR, CHIP 10K 1/16W
IC5 8-759-370-11 s IC NJM2100V-TE2 R21 1-218-957-11 s RESISTOR,CHIP 2.2K 1/16W(1608)
R22 1-218-953-11 s RESISTOR, CHIP 1K 1/16W
IC6 8-759-384-88 s IC TK10690M R23 1-218-977-11 s RESISTOR,CHIP 100K 1/16W(1005)
IC7 8-759-370-11 s IC NJM2100V-TE2
IC101 8-759-209-15 s IC TC4SU69F R26 1-220-215-11 s RESISTOR, CHIP 510K 1/16(1005)
IC103 8-759-082-60 s IC TC7S66FU R27 1-220-215-11 s RESISTOR, CHIP 510K 1/16(1005)
IC211 8-759-486-73 s IC XC62FP3302PR R28 1-218-956-11 s RESISTOR, CHIP 1.8K
R29 1-218-945-11 s RESISTOR,CHIP 220 1/16W(1005)
IC401 8-759-693-82 s IC HN58X2464FPIZ R31 1-218-973-11 s RESISTOR,CHIP 47K 1/16W (1005)
IC402 6-700-923-01 o IC XC61FN2712MR
IC404 8-759-209-15 s IC TC4SU69F R32 1-218-969-11 s RESISTOR,CHIP 22K 1/16W (1608)
---------- 102
JK-1 BOARD
----------
Ref. No.
or Q’ty Part No. SP Description
1pc A-4591-441-A s MOUNTED CIRCUIT BOARD, JK-1
C483 1-128-131-11 s CAPACITOR,ELECT 22MF/50V 105
C484 1-128-131-11 s CAPACITOR,ELECT 22MF/50V
J403 1-778-326-11 o CONNECTOR (PLUG)
JR401 1-216-864-11 s CONDUCTOR, CHIP (1608)
R490 1-216-824-11 s RESISTOR, CHIP 1.8K 1/10W 1608 106
R491 1-216-806-11 s RESISTOR,CHIP 56 1/16W 1608
R492 1-216-806-11 s RESISTOR,CHIP 56 1/16W 1608
R493 1-216-824-11 s RESISTOR, CHIP 1.8K 1/10W 1608
S5 1-692-990-21 s SWITCH, SLIDE
107
108
109
105
102
106
103
107
104
107
101 102
103
104
106
3-4-6. UWP-X2
Ref. No.
or Q’ty Part No. SP Description
101 2-347-711-11 s MANUAL, INSTRUCTION
102 A-8327-823-A s HOLDER ASSY, MICROPHONE
103 2-347-713-01 s CD-ROM
102
Section 4
Semiconductor Pin Assignments
—TOP VIEW—
MA133
MA133-TX
—TOP VIEW—
2SC3607-TE12L
—TOP VIEW—
UMZ8.2T
UMZ8.2T-T106
—TOP VIEW—
2SC5015-T1
B E
E C
WIDE
—TOP VIEW—
2SK1332-3
2SK1332-3-TL
2SK2080-TE85L
[|IC|]
AT24C64N-10SI-1.8-TR (ATMEL)
A2 IN 3 6 SCL IN INPUT/OUTPUT
G1 S
SDA : SERIAL DATA
GND 4 5 SDA I/O
7
WP
6 START
SCL
5 STOP
SDA LOGIC
SERIAL EN
CONTROL H.V. PUMP/TIMING
—TOP VIEW— LOGIC
DTA114EE (R1=10k, R2=10k) LOAD
X DEC
R1 2 R/W DATA WORD
A1 EEPROM
1 ADDR/COUNTER
A0
R2
DOUT/ACK
DIN
LOGIC
DOUT
—TOP VIEW—
DTC124EE (R1=22k, R2=22k)
DTC124EE-TL
BA033FP-E2 (ROHM)
R1 BA033T
R2 POSITIVE VOLTAGE REGULATOR
(2)
1 3
IN
GND
2 2
1 3 OUT
BA08T (ROHM)
BA17806FP-E2 (ROHM)
COM (3)
1 2
IN OUT
COM (GND)
3
FM RF IN 7 18 AM IF OUT OUT
AM RF IN IN 8 17 IF GND
NC 9 16 METER OUT
FM RF IN IN 10 15 FM IF IN IN
LMX2331LTMX (NS)
GND 11 14 AM IF IN IN
DUAL FREQUENCY SYNTHESIZER
FM/AM FE OUT 12 13 BAND SELECT IN —TOP VIEW—
INPUTS
VCC1 1 20 VCC2 CLOCK : HIGH IMPEDANCE CMOS CLOCK
INPUTS DATA : BINARY SERIAL DATA
AFC : AUTOMATIC FREQUENCY CONTROL VP1 2 19 VP2 FINIF : IF PRESCALER
AFC/AGC1, AFC/AGC2 : AUTOMATIC GAIN AND FREQUENCY CONTROL FINIF : IF PRESCALER COMPLEMENTARY
AM IF IN : AM IF INPUT STAGE DoRF OUT 3 18 DoIF OUT FINRF : RF PRESCALER
AM OSC : AM LOCAL OSCILLATOR FINRF : RF PRESCALER COMPLEMENTARY
AM RF IN : AM RF AMPLIFIER GND 4 17 GND LE : LOAD ENABLE
BAND SELECT : BAND SELECT FOR FM/AM OSCIN : OSCILLATOR
FM DISCRI : FM DISCRIMINATOR FINRF IN 5 16 FINIF IN
FM IF IN : FM IF AMPLIFIER OUTPUTS
FM OSC : FM LOCAL OSCILLATOR FINRF IN 6 15 FINIF IN DoIF : IF CHARGE PUMP
FM RF IN : FM RF AMPLIFIER DoRF : INTERNAL CHARGE PUMP
RIPPLE : RIPPLE FILTER GND 7 14 GND FoLD : MULTIPLEXED OF THE RF/IF
PROGRAMMABLE OR REFERENCE DIVIDER
OUTPUTS OSCIN IN 8 13 LE IN
AM IF OUT : AM IF OTHERS
BAND SIG : BAND SIGNAL OUTPUT WIDTH CONTROL GND 9 12 DATA IN NC : NO CONNECTION
DET : DETECTOR VCC1 : POWER SUPPLY FOR RF
FM/AM FE : AM AND FM FRONT-END FoLD OUT 10 11 CLOCK IN VCC2 : POWER SUPPLY FOR IF
METER : METER DRIVER VP1 : POWER SUPPLY FOR RF CHARGE PUMP
REG : REGULATOR VOLTAGE VP2 : POWER SUPPLY FOR IF CHARGE PUMP
OTHER
NC : NO CONNECTION
16 IF 15-BIT IF PHASE CHARGE 18
FINIF DoIF
PRESCALER N COUNTER COMP. PUMP
IFLD
FOUT
15-BIT IF LOCK
4 R COUNTER 10
AFC 8 DETECT FoLD
5 OSCIN OSCILLATOR
FM OSC FASTLOCK
7 MUX
FM RF 15-BIT RF
12
R COUNTER RFLD
10
FM RF IN FM FE FM/AM FE
8
AM RF IN AM FE 5 RF 18-BIT RF PHASE CHARGE 3
FINRF DoRF
PRESCALER N COUNTER COMP. PUMP
3
AM OSC
18
14 AM IF AM IF OUT
AM IF IN
DET AGC
11 22-BIT DATA FAST
CLOCK
21 DATA 12 REGISTER LOCK
FM IF IN
15 FM IF DET LE 13
DISCRI
2
FM DISCRI TUNING 16
METER
METER
BAND SIGNAL
24
OUTPUT CONTROL BAND SIG
20 19
AFC/AGC1 AFC/AGC2
13 6
FM/AM BAND SELECT REGULATOR REG
22
RIPPLE FILTER RIPPLE FILTER
UPC4558G2 (JRC) 2
Y=A
GND 3 4
A Y
DUAL OPERATIONAL AMPLIFIERS 0 1 0 : LOW LEVEL
—TOP VIEW— 1 0 1 : HIGH LEVEL
OUT 1 1 8 VCC
_ +
IN(_) 1 2 7 OUT 2
+ _
IN(+) 1 3 6 IN(_) 2
TC74HC4051AFT(EL) (TOSHIBA)
VEE 4 5 IN(+) 2
13 X0
X4 1 VDD 16 14 X1
15 X2
X6 2 15 X2 12 X3
1 X4 XC 3
XC 3 14 X1 5 X5
2 X6
X7 4 13 X0
NJM2406F (JRC) 4 X7
NJM2406F-TE2 X5 5 12 X3 6 OPEN
EN
A B C
SINGLE COMPARATOR EN 6 11 A
11 10 9
—TOP VIEW—
7 VEE 10 B
X0 - X7 : ANALOG INPUTS/OUTPUTS
_INPUT 1 V+ 5 8 GND 9 C
XC : COMMON INPUT/OUTPUT
_ A, B, C : CHANNEL SELECT INPUT
2 GND
+ EN : ENABLE INPUT
+INPUT 3 4 OUTPUT CONTROL INPUTS
SELECT SELECTED
EN CHANNEL
C B A
0 0 0 0 X0
0 0 0 1 X1
0 0 1 0 X2
0 0 1 1 X3
0 1 0 0 X4
0 1 0 1 X5
0 1 1 0 X6 0 : LOW LEVEL
0 1 1 1 X7 1 : HIGH LEVEL
1 x x x OPEN x : DON’T CARE
TA31161FN(EL) (TOSHIBA)
IF DETECTOR
—TOP VIEW—
IF OUT2
IF OUT1
AF OUT
QUAD
MIX IN
RSSI
TC74HC4053AFT(EL) (TOSHIBA)
16 15 14 13 12 11 10 9
GND VCC2 C-MOS TRIPLE 2-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER
DETECTOR —TOP VIEW—
RSSI
MIXER IF AMP 12 X0
Y1 I/O 1 VDD 16 13 X1 X 14
LOCAL OPEN
OSC 11 A
GND VCC1 Y0 I/O 2 15 Y I/O
1 2 3 4 5 6 7 8 2 Y0
Z1 I/O 3 14 X I/O 1 Y1 Y 15
OSC OUT
BS
MIX OUT
DEC
IF IN
OSC IN
OPEN
10 B
Z I/O 4 13 X1 I/O
5 Z0
Z0 I/O 5 12 X0 I/O 3 Z1 Z 4
OSC IN, OUT :; LOCAL OSC INPUT
OPEN
BS ; BATTERY SAVE 9 C
EN IN 6 11 A IN
MIXER OUT ; MIXER OUTPUT
EN VEE
DEC ; BIAS FOR IF INPUT
7 VEE 10 B IN 6 7
IF IN ; IF INPUT
RSSI ; RSSI OUTPUT
8 GND 9 C IN
IF OUT1, 2 ; IF LIMITTER OUTPUT
QUAD ; PHASE INPUT FOR FM DETECTOR
AF OUT ; DEMODULATION SIGNAL OUTPUT
MIX IN ; MIXER INPUT CONTROL INPUTS
SELECT ON CHANNEL
EN
C B A
0 0 0 0 Z0 Y0 X0
0 0 0 1 Z0 Y0 X1
0 0 1 0 Z0 Y1 X0
0 0 1 1 Z0 Y1 X1
0 1 0 0 Z1 Y0 X0
0 1 0 1 Z1 Y0 X1
0 1 1 0 Z1 Y1 X0 0 : LOW LEVEL
0 1 1 1 Z1 Y1 X1 1 : HIGH LEVEL
1 x x x OPEN x : DON’T CARE
CONT SWITCH
0 OFF 0 : LOW LEVEL VIN
1 ON 1 : HIGH LEVEL 3
1
VOUT
DELAY CIRCUIT
TK10690M (TOKO)
VREF
TK10690MTL
2
COMPRESSOR GND
—TOP VIEW—
NF IN 1 8 VCC
1 2 3
NF IN IN OUT
GND
1 2 3 1
_ +
2 7 GND IN OUT
SUM IN SUM OUT
3 6
REF CAP VREF G CELL CONT IN
RECT
5 RECT CAP
XC6367A331MR (TOREX)
XC6367A501MR (TOREX)
TK10691M (TOKO)
DC/DC CONVERTER CONTROLLER
TK10691MTL —TOP VIEW—
EXPANDER INPUTS
CE : CHIP ENABLE
—TOP VIEW— VOUT 1 5 EXT
VOUT : OUTPUT VOLTAGE MONITOR
VCC 2
NF IN 1 8 VCC OUTPUT
EXT : EXTERNAL TRANSISTOR CONNECTION
CE 3 4 GND
SUM IN 2 7 SUM OUT
3 6
REF CAP VREF G CELL CONT IN
RECT
5 RECT CAP
5-1. UTX-B1
MB-4
ANT
VOLTAGE
OSCILLATOR POWER
VOLUME AF SW PRE-AMP AMP LPF ISOLATOR
CONTROL PRE-AMP LIMITTER AMP COMPRESSOR PRE-EMPHASIS AMP CP101 BUFFER
CONV OSC AMP
AF L110-
Q103, L112,
IC4 IC5 IC103 Q106 Q108 C142, CP102
MIC IC1 Q1 IC2 IC6 IC7
CN1 (2/2) (1/2) C143
INPUT
CONNECTOR
LPF
Antenna power selection
30mW/5mW (except for KR model)
10mW/2mW (KR model)
TONE SIGNAL C119, R121
AF LEVEL GENERATOR
DET IC4 (1/2)
EEPROM CPU
IC401
IC402
RESET
LCD
DC-DC CONVERTER 5 V
LCD401
POWER
SWITCH
S301
UTX-B1
Circuit Description C142, C143) and is output from the antenna via the isolator
(CP102). At this time, the locked status of the PLL can be
UTX-B1 (MB-4 board) detected by monitoring the LD terminal (pin-10) of the
UTX-B1 consists of the following four blocks. PLL IC (IC102). The voltage control circuit (Q104, Q105)
1. Audio circuit and the peripheral circuit: has the function of switching ON/OFF the power voltage
Ref No. 1 through 70 series to the RF circuit. The control signal to the voltage control
2. PLL block and RF block: circuit is the RFM signal that is supplied from the CPU
Ref No. 100 series (IC405). (Power is supplied to the RF circuit when the
3. CPU and the peripheral circuit: RFM signal is “L”.)
Ref No. 400 series
4. Power supply block: Ref No. 200 series and 300 series.
3. CPU and the peripheral circuit
1. Audio circuit and the peripheral circuit The CPU (IC405) is an 8-bit microprocessor operating on
The audio input signal to the MIC INPUT connector (CN1) the 4 MHz (X401) clock frequency.
is sent to the audio attenuator (ATT) circuit (IC1) in the The CPU (IC405) performs the functions of sending out
unbalanced signal format. The ATT is set (0 to 21 dB with the PLL data, ATT (attenuation), setting the transmission
3 dB step) by the resistance value that is selected by the output power, AF muting, RF muting, LCD control and
analog switch (IC1). As the analog switch receives the 3- others by accessing the EEPROM (IC401). The voltage
bit ATT control signal (ATT0, 1, 2) from CPU (IC405), it detection circuit (IC402) detected the power supply voltage
selects the resistance value accordingly. The ATT control (+2.7 V) and uses it for resetting the CPU (IC405).
signal data is determined by the information generated by
the [+] and [_] switches (S403, S402) that send the control
data to the CPU (IC405). 4. Power supply block
The audio signal that is adjusted of its level by the ATT The DC-DC converter block (IC201, Q201, D201) gener-
circuit is buffered (Q1) and sent to the limiter circuit (IC2- ates +5 V (VCC1) from the battery voltage (3 V), and
1/2). The limiter circuit monitors the audio input signal supplies it to the audio block and RF block. The regulator
level if the input signal level is excessive or not, and circuit (IC211) generates +3.3 V (VCC2) from the +5 V
controls the input signal level so as not to exceed the set (VCC1), and supplies it to the CPU block and PLL block.
threshold level. The limiter output signal is passed through The POWER switch circuit (POWER switch: S301, Q301
a low-pass filter (IC2-2/2), is amplified (IC4-2/2) and sent to Q303) is the control circuit that turns ON/OFF the DC-
to the compressor circuit (IC6). The audio signal receives DC converter.
the signal compression at the compressor circuit with the
compression ratio of 2 :1 (compressed to 1/2), and is sent
to the pre-emphasis circuit. Time constant of the pre-
emphasis circuit is 50 us. The audio signal is then mixed
with the tone signal (X101: 32.000 kHz), is passed through
the AF switch (Q103) and is sent to the RF circuit block
(VCO: CP101). The AF level detection circuit (IC4-1/2),
D3, D4) is used to display the audio signal on the LCD
(LCD401).
5-2. UTX-H1
MB-5
ANT
VOLTAGE
OSCILLATOR POWER
VOLUME AF SW PRE-AMP AMP LPF ISOLATOR
CONTROL PRE-AMP LIMITTER AMP COMPRESSOR PRE-EMPHASIS AMP CP101 BUFFER
CONV OSC AMP
AF L110-
Q103, L112,
DM IC4 IC5 IC103 Q106 Q108 C142, CP102
Unit IC1 Q1 IC2 IC6 IC7
CN2 (2/2) (1/2) C143
INPUT
CONNECTOR
EEPROM CPU
IC401
IC402
RESET
LCD
DC-DC CONVERTER 5 V
LCD401
POWER
SWITCH
S301
UTX-H1
Circuit Description C142, C143) and is output from the antenna via the isolator
(CP102). At this time, the locked status of the PLL can be
UTX-H1 (MB-5 board) detected by monitoring the LD terminal (pin-10) of the
UTX-H1 consists of the following four blocks. PLL IC (IC102). The voltage control circuit (Q104, Q105)
1. Audio circuit and the peripheral circuit: has the function of switching ON/OFF the power voltage
Ref No. 1 through 70 series to the RF circuit. The control signal to the voltage control
2. PLL block and RF block: circuit is the RFM signal that is supplied from the CPU
Ref No. 100 series (IC405). (Power is supplied to the RF circuit when the
3. CPU and the peripheral circuit: RFM signal is “L”.)
Ref No. 400 series
4. Power supply block: Ref No. 200 series and 300 series.
3. CPU and the peripheral circuit
1. Audio circuit and the peripheral circuit The CPU (IC405) is an 8-bit microprocessor operating on
The audio input signal to the connector (CN2) from the the 4 MHz (X401) clock frequency.
Dynamic unit is sent to the audio attenuator (ATT) circuit The CPU (IC405) performs the functions of sending out
(IC1) in the unbalanced signal format. The ATT is set (0 to the PLL data, ATT (attenuation), setting the transmission
21 dB with 3 dB step) by the resistance value that is output power, AF muting, RF muting, LCD control and
selected by the analog switch (IC1). As the analog switch others by accessing the EEPROM (IC401). The voltage
receives the 3-bit ATT control signal (ATT0, 1, 2) from detection circuit (IC402) detected the power supply voltage
CPU (IC405), it selects the resistance value accordingly. (+2.7 V) and uses it for resetting the CPU (IC405).
The ATT control signal data is determined by the informa-
tion generated by the [+] and [_] switches (S403, S402)
that send the control data to the CPU (IC405). 4. Power supply block
The audio signal that is adjusted of its level by the ATT The DC-DC converter block (IC201, Q201, D201) gener-
circuit is buffered (Q1) and sent to the limiter circuit (IC2- ates +5 V (VCC1) from the battery voltage (3 V), and
1/2). The limiter circuit monitors the audio input signal supplies it to the audio block and RF block. The regulator
level if the input signal level is excessive or not, and circuit (IC211) generates +3.3 V (VCC2) from the +5 V
controls the input signal level so as not to exceed the set (VCC1), and supplies it to the CPU block and PLL block.
threshold level. The limiter output signal is passed through The POWER switch circuit (POWER switch: S301, Q301
a low-pass filter (IC2-2/2), is amplified (IC4-2/2) and sent to Q303) is the control circuit that turns ON/OFF the DC-
to the compressor circuit (IC6). The audio signal receives DC converter.
the signal compression at the compressor circuit with the
compression ratio of 2 :1 (compressed to 1/2), and is sent
to the pre-emphasis circuit. Time constant of the pre-
emphasis circuit is 50 us. The audio signal is then mixed
with the tone signal (X101: 32.000 kHz), is passed through
the AF switch (Q103) and is sent to the RF circuit block
(VCO: CP101). The AF level detection circuit (IC4-1/2),
D3, D4) is used to display the audio signal on the LCD
(LCD401).
5-3. URX-M1
MB-2
ANT-a FT103
FT101 Q101 FT102 Q103,104 SAW Q105,106 FT104 Q107 FT105 IC101 FT106 IC102 IC103 (1/2)
BPF LNA BPF 1st MIXER FILTER 2nd MIXER CF IF AMP CF IF AMP CF DETECTOR AF AMP
243.95MHz 10.7MHz
AF-a
RSSI-A
FT107 IC401 (1/3) IC401 (2/3) IC402 (1/2) IC402 (2/2) IC403 IC406 (1/2)
CERAMIC DIVERSITY SQUELCH DE-EMPHASIS LPF EXPANDER AF AMP
DISCRIMINATOR
AF OUT
50 s 25kHz 150 s
Q302,303 LCD501
VCO
+9 V (FOR AF)
EEPROM S1 SET
S2 _
+6 V (FOR IF AND AF) IC11
EEPROM S3 +
INTERFACE
9V 6V 3.3 V +3.3 V (EXCEPT FOR IF AND AF)
IC16 IC15
REGULATOR REGULATOR
DP-1
URX-M1
Circuit Description (5) 2nd local oscillator circuit paths. One output signal is the main audio output signal. 4. CPU block
The 2nd local oscillator signal is generated by the oscilla- One output signal is the main audio output signal. The The CPU (IC10) performs the following controls.
URX-M1 (MB-2 Board/DP-1 Board) tor circuit consisting of the transistors (Q302 and Q303), other output signal is connected to the (2) AF level detec-
URX-M1 consists of the following four blocks. buffered by the amplifier (antenna a = Q304, antenna b = tor circuit. (1) LCD display
1. RF block Q305) and mixed with the 1st IF signal by the (4) 2nd . Reception channel or reception frequency indication
2. AF block mixer circuit. Frequency of the 2nd local oscillator signal (2) AF level detector circuit . Audio output level indication
3. Power block is 233.25 MHz, and is kept constant by controlling the The other output of the audio signals from the main audio . RF input level indication
4. CPU block voltage applied to VARI cap diode (D301) with the PLL output signal is amplified by amplifier (IC407-2/2) and . Error message indication
The respective blocks have the following functions. IC (IC302). enters the rectifier circuit (D402). The output voltage that
is developed by the rectifier circuit is detected by the CPU (2) LED display
1. RF block (6) 2nd IF circuit (IC10). Output signal of the detector is used to indicate the . RF input level indication
The RF block consists of the six circuits as shown below. The 2nd IF signal that is output from the (4) 2nd mixer AF signal level on the LCD. The RF input level is indicated on the LED (D13) using
circuit is amplified by the transistor (antenna a = Q107, the RSSI signal. The green LED is used. The OR-logic
(1) RF amplifier circuit antenna b = Q207) and the 2nd IF amplifier IC (antenna a (3) TONE detector circuit output of the RSSI signals from the antennas “a” and “b”
The RF inputs as many as the number of antennas “a” and = IC101, antenna b = IC201). Desired frequency band of The audio output signal from the diversity circuit (IC401- is indicated.
“b” are provided. the 2nd IF signal is selected by the ceramic filter (antenna 1/3) is amplified by amplifier (IC405-2/2) containing a . Squelch (muting) control
The RF signal from which the desired frequency band
a = FT105/FT106, antenna b = FT205/FT206). filter consisting of crystal oscillator (X401, X402) and Muting of the audio signal is performed by detecting the
width is selected by the band-pass filter (antenna a =
At the same time, it outputs the DC voltage that changes its enters the rectifier (D401). Output voltage from the RSSI signal, the TONE signal and noise signal.
FT101, antenna b = FT201) is amplified by the RF amplifi-
level depending on the RF input signal level, as the RSSI rectifier is detected by the CPU (IC10). Output signal from . PLL control
er (antenna a = Q101, antenna b = Q201). The amplified
signal. The RSSI signal is used to select the diversity and the detector is used to control the (1) squelch circuit. CPU (IC10) controls the PLL IC (IC302) using the
RF signal passes through another band-pass filter (antenna
to control squelch (muting). The 2nd IF signal that is frequency data stored in the EEPROM (IC11).
a = FT102, antenna b = FT202) and is input to the 1st
amplified by the above amplifier is detected by the detector (4) Noise detector circuit . Clock oscillator circuit
mixer circuit shown as (2). Gain of the RF amplifier block
IC (antenna a = IC102, antenna b = IC202) and the ceramic The audio output signal from the diversity circuit (IC401- The clock signal (frequency is 4 MHz) is oscillated by
is about 10 dB including the loss due to the band-pass
discriminator (antenna a = FT107, antenna b = FT207), 1/3) passes through the amplifier (IC407-1/2) containing the crystal oscillator (X11) and the oscillator circuit
filters.
and is output as the audio signal. the high-pass filter having cut-off frequency 87 kHz and inside the CPU. This clock signal is used by the CPU
enters the rectifier circuit (D403). Output voltage from the (IC10) and the PLL IC (IC302).
(2) 1st mixer circuit and 1st IF amplifier circuit
2. AF block rectifier is detected by the CPU (IC10). Output signal from
The signal that is amplified by the RF amplifier is mixed
with the 1st local oscillator output signal shown as (3) by The audio signal (two channels from antennas “a” and “b”) the detector is used to control the (1) squelch circuit.
the 1st mixer circuit (antenna a = Q103/Q104, antenna b = that has passed through the high-frequency block and is
Q203/Q204). Desired frequency band is selected from the amplified by the OP amplifier (IC103) is input to the 3. Power block
mixed signal by the SAW filter (antenna a = FT103, diversity circuit (IC401-1/3). The diversity circuit is The external 9 V input power is converted of its voltage
antenna b = FT203) and is output to the (4) 2nd mixer controlled by the CPU (IC10) in accordance with the RSSI from 9 V to 6 V by the regulator IC (IC16), and is also
circuit as the 1st IF signal. Frequency of the 1st IF signal is signal that is generated by the 2nd IF amplifier IC of the converted to 3.3 V by the regulator IC (IC15). The original
243.95 MHz. high-frequency block. Output signal from the diversity external 9 V input power is used by the audio output as it
circuit takes the two signal paths: One output is connected is. The regulated 6 V power is used by the front audio
(3) 1st local oscillator circuit to the (1) squelch (muting) circuit. The other output is circuit and the detector circuit. The regulated 3.3 V power
The 1st local oscillator signal is generated by VCO connected to the (3) TONE detector circuit and the (4) is used by all circuits other than the above circuits.
(CP301), buffered by the amplifier (antenna a = Q102, noise detector circuit via the buffer amplifier (IC405-1/2)
antenna b = Q202) and mixed with the RF signal by the (2)
1st mixer circuit. The VCO (CP301) is controlled by the (1) Squelch circuit
PLL IC (IC302) and CPU (IC10). The squelch circuit (IC401-2/3) is controlled by the CPU
(IC10) in accordance with the RSSI signal the tone and the
(4) 2nd mixer circuit and 2nd IF amplifier circuit noise detector output.
The 1st IF signal is mixed with the (5) 2nd local oscillator The audio output signal from the squelch (muting) circuit
by the 2nd mixer circuit (antenna a = Q105/Q106, antenna enters the de-emphasis circuit (IC402-1/2) having time
b = Q205/Q206). Desired frequency band is selected from constant 50 us and the low-pass filter circuit (IC402-1/2)
the mixed signal by the ceramic filter (antenna a = FT104, having the cut-off frequency of 25 kHz. It then enters the
antenna b = FT204) and is output to the (6) 2nd IF circuit expander circuit (IC403). The audio output signal from the
as the 2nd IF signal. Frequency of the 2nd IF signal is 10.7 expander is buffered by the buffer amplifier (IC406-1/2)
MHz. having the waiting time of 150 us and takes the two signal
5-4. URX-P1
MB-1
ANT-a FT103
FT101 Q101 FT102 Q103,104 SAW Q105,106 FT104 Q107 FT105 IC101 FT106 IC102 IC103 (1/2)
BPF LNA BPF 1st MIXER FILTER 2nd MIXER CF IF AMP CF IF AMP CF DETECTOR AF AMP
243.95MHz 10.7MHz
AF-a
RSSI-A
FT107 IC401 (1/3) IC401 (2/3) IC402 (1/2) IC402 (2/2) IC403 IC406 (1/2) R448,445,446 Q402,405
DIVERSITY SQUELCH DE-EMPHASIS LPF EXPANDER BUFFER ATTENUATOR MUTING
CERAMIC
DISCRIMINATOR
AF OUT
50 s 25kHz 150 s
LCD
Q302,303
VCO LCD501
S3 SET
EEPROM
Q52 IC1,Q1, S2 _
POWER SWITCH D1,L1 IC11
EEPROM S1 +
DC DC +3.3 V
CONVERTER INTERFACE
BATT
URX-P1
Circuit Description (5) 2nd local oscillator circuit paths. One output signal is the main audio output signal 3. Power block
The 2nd local oscillator signal is generated by the oscilla- that is output from the output connector (AF OUT) via the The power bock consists of the following two circuits.
URX-P1 (MB-1 Board) tor circuit consisting of the transistors (Q302 and Q303), muting circuit (Q405, Q402) that suppresses the noise at
URX-P1 consists of the following four blocks. buffered by the amplifier (antenna a = Q304, antenna b = the instance of power ON/OFF. The other output is (1) POWER switch circuit
1. RF block Q305) and mixed with the 1st IF signal by the (4) 2nd connected to the (2) MONITOR output circuit and the (3) When the POWER switch (S4) is pressed to ON, the FET
2. AF block mixer circuit. Frequency of the 2nd local oscillator signal AF level detector circuit. switch (Q52) is turned on so that the power voltage is
3. Power block is 233.25 MHz, and is kept constant by controlling the supplied to the DC-DC converter circuit.
4. CPU block voltage applied to VARI cap diode (D301) with the PLL (2) MONITOR output circuit
The respective blocks have the following functions. IC (IC302). One of the audio signals from the main audio output signal (2) DC-DC converter circuit
is buffered by buffer amplifier (IC406-2/2) and passes The voltage supplied from the POWER switch circuit is
1. RF block (6) 2nd IF circuit through the level-control analog switch (IC409, IC410) converted to the +3.3 V power by the control IC (IC1) and
The RF block consists of the six circuits as shown below. The 2nd IF signal that is output from the (4) 2nd mixer and enters the monitor amplifier (IC408) from which the the switching FET (Q1).
circuit is amplified by the transistor (antenna a = Q107, audio output signal is connected to the HEADPHONES
(1) RF amplifier circuit antenna b = Q207) and the 2nd IF amplifier IC (antenna a connector. The audio monitor level is adjusted by the 4. CPU block
The RF inputs as many as the number of antennas “a” and = IC101, antenna b = IC201). Desired frequency band of analog switch IC (IC409, IC410) that is controlled by the The CPU (IC10) performs the following controls.
“b” are provided. the 2nd IF signal is selected by the ceramic filter (antenna CPU (IC10) as the “+” or “_” button is operated.
The RF signal from which the desired frequency band
a = FT105/FT106, antenna b = FT205/FT206). (1) LCD display
width is selected by the band-pass filter (antenna a =
At the same time, it outputs the DC voltage that changes its (3) AF level detector circuit . Reception channel or reception frequency indication
FT101, antenna b = FT201) is amplified by the RF amplifi-
level depending on the RF input signal level, as the RSSI The other output of the audio signals from the main audio . Audio output level indication
er (antenna a = Q101, antenna b = Q201). The amplified
signal. The RSSI signal is used to select the diversity and output signal is amplified by amplifier (IC407-2/2) and . Battery power consumption indication
RF signal passes through another band-pass filter (antenna
to control squelch (muting). The 2nd IF signal that is enters the rectifier circuit (D402). The output voltage that . RF input level indication
a = FT102, antenna b = FT202) and is input to the 1st
amplified by the above amplifier is detected by the detector is developed by the rectifier circuit is detected by the CPU . Accumulated operating hours indication
mixer circuit shown as (2). Gain of the RF amplifier block
IC (antenna a = IC102, antenna b = IC202) and the ceramic (IC10). Output signal of the detector is used to indicate the . Error message indication
is about 10 dB including the loss due to the band-pass
discriminator (antenna a = FT107, antenna b = FT207), AF signal level on the LCD.
filters.
and is output as the audio signal. (2) LED display
(4) TONE detector circuit . RF input level indication
(2) 1st mixer circuit and 1st IF amplifier circuit
2. AF block The audio output signal from the diversity circuit (IC401- The RF input level is indicated on the LED (D13) using
The signal that is amplified by the RF amplifier is mixed
with the 1st local oscillator output signal shown as (3) by The audio signal (two channels from antennas “a” and “b”) 1/3) is amplified by amplifier (IC405-2/2) containing a the RSSI signal. The green LED is used. The OR-logic
the 1st mixer circuit (antenna a = Q103/Q104, antenna b = that has passed through the high-frequency block and is filter consisting of crystal oscillator (X401, X402) and output of the RSSI signals from the antennas “a” and “b”
Q203/Q204). Desired frequency band is selected from the amplified by the OP amplifier (IC103) is input to the enters the rectifier (D401). Output voltage from the is indicated.
mixed signal by the SAW filter (antenna a = FT103, diversity circuit (IC401-1/3). The diversity circuit is rectifier is detected by the CPU (IC10). Output signal from . Squelch (muting) control
antenna b = FT203) and is output to the (4) 2nd mixer controlled by the CPU (IC10) in accordance with the RSSI the detector is used to control the (1) squelch circuit. Muting of the audio signal is performed by detecting the
circuit as the 1st IF signal. Frequency of the 1st IF signal is signal that is generated by the 2nd IF amplifier IC of the RSSI signal, the TONE signal and noise signal.
243.95 MHz. high-frequency block. Output signal from the diversity (5) Noise detector circuit . PLL control
circuit takes the two signal paths: One output is connected The audio output signal from the diversity circuit (IC401- CPU (IC10) controls the PLL IC (IC302) using the
(3) 1st local oscillator circuit to the (1) squelch (muting) circuit. The other output is 1/3) passes through the amplifier (IC407-1/2) containing frequency data stored in the EEPROM (IC11).
The 1st local oscillator signal is generated by VCO connected to the (4) TONE detector circuit and the (5) the high-pass filter having cut-off frequency 87 kHz and . MONITOR level control
(CP301), buffered by the amplifier (antenna a = Q102, noise detector circuit via the buffer amplifier (IC405-1/2) enters the rectifier circuit (D403). Output voltage from the The MONITOR level is adjusted by controlling the
antenna b = Q202) and mixed with the RF signal by the (2) rectifier is detected by the CPU (IC10). Output signal from analog switch IC (IC409, IC410) in accordance with the
1st mixer circuit. The VCO (CP301) is controlled by the (1) Squelch circuit the detector is used to control the (1) squelch circuit. “+” and “_” button operations.
PLL IC (IC302) and CPU (IC10). The squelch circuit (IC401-2/3) is controlled by the CPU . Clock oscillator circuit
(IC10) in accordance with the RSSI signal the tone and the The clock signal (frequency is 4 MHz) is oscillated by
(4) 2nd mixer circuit and 2nd IF amplifier circuit noise detector output. the crystal oscillator (X11) and the oscillator circuit
The 1st IF signal is mixed with the (5) 2nd local oscillator The audio output signal from the squelch (muting) circuit inside the CPU. This clock signal is used by the CPU
by the 2nd mixer circuit (antenna a = Q105/Q106, antenna enters the de-emphasis circuit (IC402-1/2) having time (IC10) and the PLL IC (IC302).
b = Q205/Q206). Desired frequency band is selected from constant 50 us and the low-pass filter circuit (IC402-2/2)
the mixed signal by the ceramic filter (antenna a = FT104, having the cut-off frequency of 25 kHz. It then enters the
antenna b = FT204) and is output to the (6) 2nd IF circuit expander circuit (IC403). The audio output signal from the
as the 2nd IF signal. Frequency of the 2nd IF signal is 10.7 expander is buffered by the buffer Amplifier (IC406-1/2)
MHz. having the waiting time of 150 us and takes the two signal
5-5. URX-R1
MB-3
ANT-a FT103
FT101 Q101 FT102 Q103,104 SAW Q105,106 FT104 Q107 FT105 IC101 FT106 IC102 IC103 (1/2)
BPF LNA BPF 1st MIXER FILTER 2nd MIXER CF IF AMP CF IF AMP CF DETECTOR AF AMP
243.95MHz 10.7MHz
AF-a JK-1
RSSI-A
IC410,409
FT107 IC401 (1/3) IC401 (2/3) IC402 (1/2) IC402 (2/2) IC403 IC405 (1/2) BALANCED Q407,408 R490-493
DIVERSITY SQUELCH DE-EMPHASIS LPF EXPANDER BUFFER AF AMP MUTING LINE/MIC
CERAMIC
DISCRIMINATOR
BALANCED
50 s 25kHz 150 s AF OUT
LCD
Q302,303
VCO LCD501
EEPROM S1 SET
IC11 S2 _
EEPROM
+8 V (FOR AF) S3 +
INTERFACE
9V
8V 3.3 V +3.3 V (EXCEPT FOR AF)
Circuit Description (5) 2nd local oscillator circuit signal paths. The first audio output signal is the unbal- 3. Power block
The 2nd local oscillator signal is generated by the oscilla- anced audio output signal that is amplified by the AF The power bock consists of the switch circuit and regula-
URX-R1 (MB-3 Board/DP-2 Board/JK-1 Board) tor circuit consisting of the transistors (Q302 and Q303), amplifier (IC405-2/2) up to the LINE signal level and is tor.
URX-R1 consists of the following four blocks. buffered by the amplifier (antenna a = Q304, antenna b = output from the output connector (UNBALANCED AF
1. RF block Q305) and mixed with the 1st IF signal by the (4) 2nd OUT) via the muting circuit (Q410) that suppresses the (1) POWER switch circuit
2. AF block mixer circuit. Frequency of the 2nd local oscillator signal noise at the instance of power ON/OFF. The second audio When the POWER switch (S4) is pressed to ON, the FET
3. Power block is 233.25 MHz, and is kept constant by controlling the output signal is the balanced audio output signal that is switch (Q52) is turned on so that the power voltage
4. CPU block voltage applied to VARI cap diode (D301) with the PLL converted to the balanced output audio signal by the supplied from the AC adapter is output to the regulator.
The respective blocks have the following functions. IC (IC302). balanced output circuit (IC410, IC409) and is output from
the output connector via the muting circuit (Q407, Q408) (2) Regulator
1. RF block (6) 2nd IF circuit that suppresses the noise at the instance of power ON/OFF, The unregulated voltage supplied from the POWER switch
The RF block consists of the six circuits as shown below. The 2nd IF signal that is output from the (4) 2nd mixer and the LINE/MIC level switching circuit (R490 to R493, that is originally generated by AC adapter is converted to
circuit is amplified by the transistor (antenna a = Q107, S5). The third output is connected to the (2) MONITOR the regulated 8 V and the regulated 3.3 V by the regulator
(1) RF amplifier circuit antenna b = Q207) and the 2nd IF amplifier IC (antenna a output circuit and the (3) AF level detector circuit. IC (IC1, IC2).
The RF inputs as many as the number of antennas “a” and = IC101, antenna b = IC201). Desired frequency band of The regulated 8 V is used in the audio output circuit and
“b” are provided. the 2nd IF signal is selected by the ceramic filter (antenna (2) MONITOR output circuit the regulated 3.3 V is used in all circuit other than the
The RF signal from which the desired frequency band
a = FT105/FT106, antenna b = FT205/FT206). One of the audio signals that are branched by the buffer audio output circuit.
width is selected by the band-pass filter (antenna a =
At the same time, it outputs the DC voltage that changes its amplifier (IC405-1/2) is buffered by buffer amplifier
FT101, antenna b = FT201) is amplified by the RF amplifi-
level depending on the RF input signal level, as the RSSI (IC406-2/2) and passes through the level-control analog 4. CPU block
er (antenna a = Q101, antenna b = Q201). The amplified
signal. The RSSI signal is used to select the diversity and variable resistor (RV400) and enters the monitor amplifier The CPU (IC10) performs the following controls.
RF signal passes through another band-pass filter (antenna
to control squelch (muting). The 2nd IF signal that is (IC408) from which the audio output signal is connected to
a = FT102, antenna b = FT202) and is input to the 1st
amplified by the above amplifier is detected by the detector the HEADPHONES connector. (1) LCD display
mixer circuit shown as (2). Gain of the RF amplifier block
IC (antenna a = IC102, antenna b = IC202) and the ceramic . Reception channel or reception frequency indication
is about 10 dB including the loss due to the band-pass
discriminator (antenna a = FT107, antenna b = FT207), (3) AF level detector circuit . Audio output level indication
filters.
and is output as the audio signal. The other output of the audio signals that are branched by . RF input level indication
the buffer amplifier (IC405-1/2) is amplified by buffer . Error message indication
(2) 1st mixer circuit and 1st IF amplifier circuit
2. AF block amplifier (IC407-2/2) and enters the rectifier circuit
The signal that is amplified by the RF amplifier is mixed
with the 1st local oscillator output signal shown as (3) by The audio signal (two channels from antennas “a” and “b”) (D402). The output voltage that is developed by the (2) LED display
the 1st mixer circuit (antenna a = Q103/Q104, antenna b = that has passed through the high-frequency block and is rectifier circuit is detected by the CPU (IC10). Output . RF input level indication
Q203/Q204). Desired frequency band is selected from the amplified by the OP amplifier (IC103) is input to the signal of the detector is used to indicate the AF signal level The RF input level is indicated on the LED (D13) using
mixed signal by the SAW filter (antenna a = FT103, diversity circuit (IC401-1/3). The diversity circuit is on the LCD. the RSSI signal. The green LED is used. The OR-logic
antenna b = FT203) and is output to the (4) 2nd mixer controlled by the CPU (IC10) in accordance with the RSSI output of the RSSI signals from the antennas “a” and “b”
circuit as the 1st IF signal. Frequency of the 1st IF signal is signal that is generated by the 2nd IF amplifier IC of the (4) TONE detector circuit is indicated.
243.95 MHz. high-frequency block. Output signal from the diversity The audio output signal from the diversity circuit (IC401- . Squelch (muting) control
circuit takes the two signal paths: One output is connected 1/3) is amplified by amplifier (IC404-1/2) containing a Muting of the audio signal is performed by detecting the
(3) 1st local oscillator circuit to the (1) squelch (muting) circuit. The other output is filter consisting of crystal oscillator (X401, X402) and RSSI signal, the TONE signal and noise signal.
The 1st local oscillator signal is generated by VCO connected to the (4) TONE detector circuit and the (5) enters the rectifier (D401). Output voltage from the . PLL control
(CP301), buffered by the amplifier (antenna a = Q102, noise detector circuit via the buffer amplifier (IC404-1/2) rectifier is detected by the CPU (IC10). Output signal from CPU (IC10) controls the PLL IC (IC302) using the
antenna b = Q202) and mixed with the RF signal by the (2) the detector is used to control the (1) squelch circuit. frequency data stored in the EEPROM (IC11).
1st mixer circuit. The VCO (CP301) is controlled by the (1) Squelch circuit . Clock oscillator circuit
PLL IC (IC302) and CPU (IC10). The squelch circuit (IC401-2/3) is controlled by the CPU (5) Noise detector circuit The clock signal (frequency is 4 MHz) is oscillated by
(IC10) in accordance with the RSSI signal the tone and the The audio output signal from the diversity circuit (IC401- the crystal oscillator (X11) and the oscillator circuit
(4) 2nd mixer circuit and 2nd IF amplifier circuit noise detector output. 1/3) passes through the amplifier (IC407-1/2) containing inside the CPU. This clock signal is used by the CPU
The 1st IF signal is mixed with the (5) 2nd local oscillator The audio output signal from the squelch (muting) circuit the high-pass filter having cut-off frequency 87 kHz and (IC10) and the PLL IC (IC302).
by the 2nd mixer circuit (antenna a = Q105/Q106, antenna enters the de-emphasis circuit (IC402-1/2) having time enters the rectifier circuit (D403). Output voltage from the
b = Q205/Q206). Desired frequency band is selected from constant 50 us and the low-pass filter circuit (IC402-2/2) rectifier is detected by the CPU (IC10). Output signal from
the mixed signal by the ceramic filter (antenna a = FT104, having the cut-off frequency of 25 kHz. It then enters the the detector is used to control the (1) squelch circuit.
antenna b = FT204) and is output to the (6) 2nd IF circuit expander circuit (IC403). The audio output signal from the
as the 2nd IF signal. Frequency of the 2nd IF signal is 10.7 expander is buffered by the buffer amplifier (IC405-1/2)
MHz. having the waiting time of 150 us and takes the three
Section 6
Board Layouts
MB-4 -A SIDE-
SUFFIX: -12
MB-4 -B SIDE-
SUFFIX: -12
MB-5 -A SIDE- MB-5 -B SIDE-
SUFFIX: -12 SUFFIX: -12
6-3. URX-M1
6-4. URX-P1
DP-1 -A SIDE-
SUFFIX: -12
MB-1 -A SIDE-
SUFFIX: -12
DP-1 -B SIDE-
SUFFIX: -12
MB-1 -B SIDE-
SUFFIX: -12
UWP Series 6-3 6-3
MB-3, DP-2, JK-1 MB-3, DP-2, JK-1
6-5. URX-R1
DP-2 -A SIDE-
SUFFIX: -12
JK-1 -A SIDE-
SUFFIX: -12
MB-3 -A SIDE-
SUFFIX: -12
Section 7
Schematic Diagrams
1
7-1. UTX-B1 Q104
5V 2SA1965 4.8V 4.8V ANT1
5V ISOLATOR TP6
C133 2p 50V CK
R128 RV102 L109 CT101 RF
5.6nH
R126
L108
3.3V PLL-IC 390 R129 R133 47k 5.6nH 3p L110 L111 L112 NM
L101 47k 18k
R110 IC103 10k 1/16W 2.2V TRIMMER 15nH 15nH 15nH
TONE 100 5.6nH 0V 3.3V TC7S66FU 4.8V
4
LD R114 10k 2.9V 4V IN OUT
20 19 18 17 16 15 14 13 12 11
9 10
Q101 3V 0.7V (TE85R) 0.7V C135
CLK LD
2SK1332-3-TL 3.3V R131 2p R140
IC101 L105 VCO 47k 50V R143
3
3.2V
TC4SU69F 0V
DATA GND 1.6 RV103 220µH 1/16W CK RF_AMP 1V 3.3k 3.3 GND GND
(TE85R) 1.6V 1.5V L103 4MHz 1.7V 47k CP101
3 4 5 6 7 8
3.2V LE OSC C134
5.6nH * J R132
R117 1k
R116 1k
R115 1k
2SC5015-T1
0.1 GND GND 10V 2SC3607
R141 10k
R103 0V 1.6 22p 22p 0.7V 220µH 2.7V 1/16W 1V *
R101 100k 10V 50V 50V A -TE12L
Q106
3.3V
6
10M 3 2 1 B IF-IN- RF-IN- CH CH IN 5V VCC OUT 0.2V
1/10W Q102 C131 R136 R139
2SC4738-YGR FIN *
VSS
NC
5
R118 R125 GND CONT GND GND 50V
2SA1965
3.2V R122 R123 CN101
GND GND 150 4.7k CH Q107
Q105
1.5V R106 1k 1k 2SC4738-Y
DO
VDD
1k 2V
4
1.7V CP2 CP1 VC MOD 0.6V
1V
X
3.3V
UMZ8.2T-T106
C115 0.2V
C137 3p 50V CJ
1.5V C119
C142 3p 50V CJ
C143 3p 50V CJ
3.3V
C108 1 16V A
3.2V 22 RV101
R135 10 1/16W
1.6V 0.8V VCC2 VCC1 50V 39nH
D101
R120 B 10V Q103 47k
C129 22 10V B
R138 100k
C105 B DTC124EE
R104 1.5k
R102 22
R134 15k
0.1
R137 1k
470k 1.6V 1.6V 1.3V
1/16W 10V
R142 *
B R108 1.2k
R112 100k
IC102 C124
C101 X101 C102 C103 C106 C110 LMX2331 C120 C121 220 C126 C138
32KHz 0.01 C113 R121 0.047 47 0.7V R130 0.001
22p 27p 0.1 R107 0.1 100p 220 0.001 4V
50V 50V 10V 33k 10V 16V 1/16W 16V 50V B 6.3V D105 47k 50V
B 50V F B B
CH CH B
C104
B
C109 C111 C112
CH
C406
B
C123 C125 C127
MA133-TX
2
10 100p 100p 0.01 0.01 R127 47 0.01 47p D106 D107
DATA
AFM
RFP
4.7k 6.3V 1SS355 MA133-TX
LD
10V 50V 50V 16V 16V 16V 50V
LE
CK
A CH CH B B B B CH RFM TE-17
4MHZ
TONE AUDIO FREQ
C45
5V 10
FL2 BUFFER LIMITER LPF COMPARATOR D ALO AMP COMPRESSER PRE_EMP DET-AMP 5V CLIP 10V
FILTER L1 A
M1 M 10µH
LAV IN OUT ATT
A 5V G 4.4V R63
C24 4.7 10V A
8
2.7k 10 NJM4580V 4.7 NF IN VCC
220p R70
V+ V+
R48 330p NJM2100
0.0022 50V B
R10 10V 10V F 2.5V R31 100
9 10 11 12 13 14 15 16
R11 100k
7
1.8k 330p V+ C14
MA133-TX
C30
Ii1 SUM OUT Ii1 1/16W OUT1
8.2k
8
C40 0.15 R44 1k R43
2.5V 50V 2.5V 2.5V 1.8V -IN 5V 2.5V 2.5V 2.5V 2.5V 10 V+
CN1 R4 B 10V R69
D1
REF CAP
2.5V OUT2 3.3V 2.5V 1.5V 2.5V
6
2.5V
5
1.5k V+ A 15k OUT2
7
C11 R22 R62
R40 4.7k
ECM-VCC C4 2.5V 2.5V 0V R49 2.5V C35 2.5V Ii1
10 R5 C7 10 1k GND 100k 4.7 15k 2.5V 2.5V 2.5V
-
+
3
5
1k RV1 V- GND RECT CAP V-
1/16W
R51 10k
10V 0.1 10V In1 In2 10V In2
R23 100k
Ii2 Q4
6
FB1 10k
R42 100k
R32 22k
A 10V A 2.5V 2.5V A 2SA1832-YGR In1 Ii2 C42
R53 100k
FL1 R6 B 2.5V 1V 1.5V 2.5V 0.0022
R46 1k
C23
4
4
680 V- 2.5V
C5 0.01 16V B
5
0V H V-
2SC4738-YGR
C
R34 10k
IN OUT R7 2SK208-O TK10690MTL 1V
R71 In2 B
S 100k
470
R21 2.2k
IC1
R36 100k
GND
Q7
TC74HC4051
R9 22k
R73 R74
MA133-TX
R52 10k
R8 D2
R39 1k
AFS Q6 5.6k 5.6k
1.2k 1SS355TE
R29 2SC4738-YGR 1/16W 1/16W
3
D3
-17
R35 10k
C2 C6 2.5V 220 C31 C27 C29 C36 0.4V
R67 C41 C43
C32 C34 R66 4.7
22 2.2 R15 680p 22 0.1 C21 10 1 0.1 R65 2.2k 4.7k 680p
10V 16V 10k R26 R28 50V 10V 10V 2.2 16V 2.2k 1/16W 1/16W 10V 50V
B A 510k 1.8k B B B 10V A 10V A B
A B 1/16W
C3 R18 10k R41 C18 C22 R45 C37 C38 C19 C28 C16 C17
0.001 100k 10 4.7 100k 10 10 4.7 0.0033 4.7 4.7
50V R19 10k R27 10V 10V 10V 10V 10V 16V 10V 10V
B 510k A A A A A B A A
ATT2
ATT1
ATT0
R20 10k
3.3V
5V R414 3.3V
10
S19
S18
S17
S16
S15
S14
S13
S12
S11
S10
COM2
COM3
L201 5V DC-DC-CONVERTOR R417 R415
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
S1
S2
S3
S4
S5
S6
S7
S8
S9
1.7V
47µH D201 5V
10k LCD401 10
3V C5-K3L MA2Z748 5V NM
TC4SU69F (TE85R)
MA133-TX
5 4
D403
0.001 50V B
2.2V 1 2 3 4 5 6 7 8 9 10 11 12 C415
VCC
XP151A13A0MR
0.01
IC404
COM2 COM3
C411
IC201 3.3V 16V
XC6367A501MR 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 3.3V B
Q201
5 4
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
PD4/SEG20
PD3/SEG19
PD2/SEG18
PD1/SEG17
PD0/SEG16
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
EEPROM SEG1 R421 C421
EXT GND 0.01 NC GND
3.3V S0 10k
64 63 62 61
1 2 3 L202 2.3V
10µH IC401 COM2 R422 C420
10V PD7/SEG23 COM2 38 10k 10
AT24C32N -10SI-1.8-TR CK COM1 10V COM1 COM0 R416
PF0/SEG24 COM1 37 A 10
3V C206 AFM COM0 13 14 15 16 17 18 19 20 21 22 23 24
4 3 2 1
5 6 7 8
COM1
COM0
C201 100 10V 10V A1 WP 66 PF2/SEG26 VLC1 35
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
0.1 10V B 10V B B 0V C425
C SK/CLK VLC2 0.01 1.6V
A2 SCL 67 PF3/SEG27 VLC2 34 16V
C203 3.3V R424 0.3V
IC211 C205 DATA PLL_DATA VLC3 3.3k B
XC62FP3302PR 100 10 GND SDA
C403 68 PF4/SEG28 VLC3 33
10V 10V 0.01 LE PLL_LE VL
5V C 16V 69 PF5/SEG29 IC405 VL 32 C416 5p 50V CH
1 VIN VOUT 2 3.3V B VDD
70 VDD CXP83516 VSS 31
VSS X401
C402 R426 330 1.6V
4MHz CT401 U6264/CN U6668/AU CE62 J CE67 KR
VSS 3.3V 3.3V 100 XTAL
10V 71 PI0/TX XTAL 30 20p TRIMMER
3 C EXTAL 2.2K 2.2K 1.5K 3.9K
3.3V REGULATOR 72 PI1/TEX EXTAL 29 R139 1.5K 3.9K
IC402 C404 RST 1.3V C417
0.1 10V B 73 NC RST 28 27p 50V CH
C211 C212 XC61FN2712MR RFM
1 1 RESET 3.3V 74 PF6/SEG30 PA7/AN7 27 R142 4.7 4.7 4.7 100 4.7 100
16V 16V
A A 2 3 75 PF7/SEG31 PA6/AN6 26
R402 TEST ALO CP101 MVU-770 MVU-799 MVU-815 MVU-815 MVU-853 MVU-746
1 4.7k 76 PE0/INT0/EC PA5/AN5 25 (VCO)
+KEY
21 22 23 24
77 PE1/INT1 PA4/AN4
3.3V C405 -KEY CP102
78 PE2/INT2 PA3/AN3 3.3V 0770M 0794M 0807M 0807M 0850M 0746M
0.1 3.3V (ISOLATOR)
10V SET BAT0
B 79 PE3/INT3 PA2/AN2
R412 10k
R411 10k
R410 10k
PB2/SCK0
PB5/SCK1
PH0/INT4
PE6/ADJ
PB1/CS0
PB3/SI0
PB4/SO0
PB6/SI1
PB7/SO1
PA0/AN0
80 PE4/RMC PA1/AN1
R425
PE5/TO
1.5k
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
PB0
3V
1.5V LEVEL DIAGRAM
FL301 FILTER Q302 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
EEP_DI/DO
P_OFF_IN
P_LED
ATT0
ATT1
ATT2
D401
GND DTC124EE SML-310LTT86 Frequency
R305 -17 Deviation
-20 ±5 kHz
100k 0V
TP1
S301 TEST
5
3V
4 2.2V
UMZ8.2T-T106
-26
2P2S TP2 -27.8 -27.8
R306 C303 TXD
D301
R303 1.5V
BATT
2.2k R304 - +
SET
2.4V 27k R404 R407 R405 R408 R406 R409 -54.5 -54.5 -54.5
10k 1k 10k 1k 10k 1k -60 -60
0.7V
SWITCH, PUSH
SWITCH, PUSH
Q303
2SC4738-YGR
S402
S403
C133 2p 50V CK
CT101
5.6nH
L108
3.3V PLL-IC 47k 390 R129 47k 5.6nH TRIMMER 15nH 15nH 15nH
4V
R110 L101 IC103 10k 2.2V
4
2.9V 4.8V IN OUT
TONE Q101 100 5.6nH 0V 3.3V TC7S66FU C135
20 19 18 17 16 15 14 13 12 11
9 10
2SK1332-3-TL 3V LD 0.7V (TE85R) 0.7V 2p
IC101 CLK LD
R131 50V R140 R143
3
3.3V R114 10k VCO GND GND
TC4SU69F 3.2V DATA GND 47k CK RF_AMP 1V 3.3k 3.3
(TE85R) 1.6V RV103 L105 1/16W
1.6V 1.5V
0V
4MHz 1.7V 220µH CP101
3.2V C107 L103 47k * C134
3 4 5 6 7 8
LE OSC 4.8V 1V
2SC5015-T1
0.1 5.6nH J 4.7 R132 Q108 CP102
5
OUT VCC R139
10V GND GND C116 C117 2.8V 2.7V
10V 2.2k R136 * 2SC3607 *
R103
Q106
B 0V 1.6V 22p 22p 0.7V A 1/16W 33 1V -TE12L
R101 100k 50V 50V
Q102
6
10M 3 2 1 IF-IN- RF-IN- IN 5V VCC OUT
R117 1k
R116 1k
R115 1k
2SC4738-YGR 3.3V CH CH
1/10W 2.8V FIN L106 2V C131
VSS
NC
5
R118 GND CONT GND GND
GND GND 150 R122 R123 4.7k 50V 0.2V 10k CN101
R106 CH
2SA1965
1.7V 1.5V DO
1k 1k 0.2V
VDD
1k
Q105
3
4
CP2 CP1 VC MOD 1V
X
UMZ8.2T-T106
4
C129 22 10V B
3.3V 1.3V
C104 10 10V A
C143 3p 50V CJ
3.3V 50V 47
C142 3p 50V CJ
3.2V 47k 1SS355
C108 1 16V A
VCC2 VCC1 B RV101
D101
1.6V 0.8V 47k
R120
R138 100k
C105 R111
L102 39nH
R104 1.5k
R108 1.2k
R102 22
R134 15k
2SC4738-Y
0.1 22
R137 1k
470k 1.6V 1.6V 1.3V
R142 *
10V
Q107
1/16W B
R112 100k
R127
4.7k
IC102 C120
C101 X101 C102 C106 C110 LMX2331 C126 C138
22p 32KHz 27p
C103
0.1 0.1 0.01 R121 0.047 C121
16V 0.001 Q103 C124 47 0.7V R130 0.001
R107 10V 16V 270 DTC124EE 220 6.3V 47k 50V
50V 50V 10V 33k B B 1/16W F 50V 4V B D105 B
CH CH B B B MA133-TX
C109 C111 C112 C113 C123 C125 C127 R135 D107
100p 0.01 47 0.01 47p MA133-TX
DATA
RFP
100p 100p 10
LD
50V 16V 50V 6.3V 16V 50V
LE
CK
50V CH B AFM B B CH RFM 1/16W
CH CH
4MHZ 2
TONE AUDIO FREQ
C45
5V 10
ATT 10V
FL2 L1 BUFFER LIMITER LPF COMPARATOR D ALO AMP COMPRESSER PRE_EMP DET-AMP 5V CLIP A
NM nm IC1
TC74HC4051
M M2 IN OUT
AFS A 5V
C24 4.7 10V A G IC5 5V 4.4V R63
18k
RV2
MA133-TX
4.7
8
10 NJM4580V R37 V+ 330p NF IN VCC V+ B 5V
ECM-VCC 10V 10k R48 2.5V 50V 10V R61 220p R70
100 I NJM2100
2.5V F
9 10 11 12 13 14 15 16
2.5V 2.5V
D1
R3 C11 IC3 1k A Q5 50V 1/16W
8 7 6 5 4 3 2 1
R12 100k
R11 100k
A B 6.8k
R14 10k
SUM IN 1.5V
R31 47k
1.8k 10 C12 OUT1 NJM2406F-TE2 OUT2 OUT2
2SC4738-YGR B
7
V+ 1/16W
0.0022 B
10V R22 330p Ii1 SUM OUT Ii1 OUT1
8
C4 C14 V+
A 1k 50V 2.5V 2.5V 1.8V -IN 5V 2.5V R43 2.5V 2.5V 2.5V
C30
10 R4 B OUT2 8.2k REF CAP 10 3.3V 1.5V R69 2.5V
2.5V 2.5V
6
10V
5
R57 5.6k 1/16W
1.5k V+ 10V 15k OUT2
R40 4.7k
7
A
R51 10k
FILTER 2.5V 2.5V 2.5V 0V 2.5V C35 2.5V Ii1
R5 C7 RV1 GND 4.7 15k 2.5V 2.5V 2.5V
-
+
3
5
IN OUT 0V 1k V- GND RECT CAP V-
1/16W
0.1 In1 10k In2 10V In2
R23 100k
Ii2
R42 100k
6
2.5V Q4 C42
R32 22k
GND 10V A In1 Ii2
R53 100k
R6 2SA1832-YGR
C3 0.001 50V B
R46 1k
R71 100k
C23
4
680 V- 2.5V
C9 2.2 16V A
5
H V-
B
R34 10k
2SK208-O 2.5V TK10690MTL In2
2SC4738-YGR
R7 S C 1V
470
R21 2.2k
R67
R9 22k
R73 R74
MA133-TX
Q7
R8 D2 Q6 4.7k
C5 nm
R36 100k
D3
1/16W 1/16W
R52 10k
-17
R35 10k
R39 1k
C6 2.5V C27 C36 0.4V C43
C31 C29 C32 C34 C41
C2 2.2 R15 680p 22 0.1 C21 10 1 0.1 R65 R66 4.7 680p
nm 16V 10k R26 R28 R29 50V 10V 10V 0.1 10V 16V 10V 2.2k 2.2k 10V 50V
A 510k 1.8k 220 B B B A A B 1/16W 1/16W A B
5V R414 3.3V
10
S19
S18
S17
S16
S15
S14
S13
S12
S11
S10
COM2
COM3
L201 5V DC-DC-CONVERTOR R417
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
S1
S2
S3
S4
S5
S6
S7
S8
S9
R415 1.7V
47µH D201 5V
10k LCD401
3V C5-K3L MA2Z748 5V NM 10
TC4SU69F (TE85R)
MA133-TX
5 4
D403
0.001 50V B
2.2V IC201 1 2 3 4 5 6 7 8 9 10 11 12 C415
XP151A13A0MR
XC6367A501MR VCC
0.01
IC404
COM2 COM3
C411
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 16V
Q201
3.3V 3.3V B
5 4
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
PD4/SEG20
PD3/SEG19
PD2/SEG18
PD1/SEG17
PD0/SEG16
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
EEPROM
EXT GND R421 C421 NC GND
3.3V S0 10k 0.01
64 63 62 61
5 6 7 8
COM1
COM0
C201 10 10V A1 WP 66 PF2/SEG26 VLC1 35
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
0.1 10V B 10V 10V 0V C425 1.6V
C B SK/CLK VLC2 0.01
A2 SCL 67 PF3/SEG27 VLC2 34 16V
C203 C204 3.3V R424 0.3V
IC211
XC62FP3302PR
TP5
3.3V 100 0.1
10V 10V
GND SDA
C403
0.01
DATA
LE
DI/DATA
PLL_LE
68 PF4/SEG28 VLC3 33
VLC3
VL
3.3k B
4
5V 3.3V C B 16V 69 PF5/SEG29 IC405 VL 32 C416 5p 50V CH
1 VIN VOUT 2 3.3V B VDD
70 VDD CXP83516 VSS 31
VSS
1.6V
X401
C402 R426 330 4MHz CT401
VSS 3.3V 100 XTAL
3.3V REGULATOR 10V 71 PI0/TX XTAL 30 20p TRIMMER
3 C EXTAL
72 PI1/TEX EXTAL 29
IC402 C404 RST 1.3V C417
0.1 73 NC RST 28 18p 50V CH U6264/CN U6668/AU CE62 J CE67 KR
C211 C212 XC61FN2752ML RFM
1 1 3.3V
10V 74 PF6/SEG30 PA7/AN7 27
RESET B
16V 16V
A A 2 3 75 PF7/SEG31 PA6/AN6 26 R139 2.2K 2.2K 2.2K 4.7K 1.8K 3.9K
R402 TEST ALO
1 4.7k 76 PE0/INT0/EC PA5/AN5 25
+KEY
21 22 23 24
R412 10k
R411 10k
R410 10k
PB2/SCK0
PB5/SCK1
PH0/INT4
PE6/ADJ
PB1/CS0
PB3/SI0
PB4/SO0
PB6/SI1
PB7/SO1
PA0/AN0
80 PE4/RMC PA1/AN1
R425
PE5/TO
1.5k CP102
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
3V
EEP_DI/DO
3V FMMT717TA 3V
RXD
TXD
RFP
P_LED
ATT0
ATT1
ATT2
IN OUT
PLL_LD
R403 D401
GND Q401 47k SML-310LTT86 3.3V
R305 DTC124EE LEVEL DIAGRAM
100k 0V TP1
S301 2.2V
TEST
4 dBV
3V
BATT 2SC4738-YGR 3V
10V RXD
3.3V
-26
3V
UMZ8.2T-T106
-27.8 -27.8
0.1V
D301
+
SET
27k -40
R407
Q303
2SC4738-YGR
R308 47k
S403
S402
SET - + A B C D E F G H I J MB-5
BOARD NO. 1-687-309-12
6 7 8 1
5 4 3 2
L112 L113 C143 L123 C151 C152 C153
LED 0µH 220nH 0.001 47µH 0.01 0.01 4.7 C155 L124
CN502 0P B 10 47µH
L100 100nH
C101 B 16V 10V
220p 2'nd MIX 1.3V
GND 1 R128 L114 L121
COM2
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
COM3
NM 100nH 0µH R147
GND 2 1V 3.3V 220 2.4V 1.3V 1.2V 6V
C117 1V 1.4V
RF AMP 220p C134 3.3V
3.3V 3 FT101 R129 3.2V 68p
R121
15
68k
R124 2.2 C145 16 14 13 12 11 10 9 13 14 15 16 17 18 19 20 21 22 23 24
1 8 7 6 68k 0.1
3.3V 4 Q103
GND2
C127
MIX IN
IF OUT2
IF OUT1
QUAD
METER
L105 B
VCC
RSSI
VCC2
BAND SEL
AM IF IN
FM IF IN
AFC/AGC2
AFC/AGC1
DET CONT
AF OUT
IF GND
FILTER
RIPPLE
3SK255 R130 3p R132 R134 R138 L122
AM IF OUT
DET OUT
0µH C135
CXA1611N-T4
LED RF 5 L103 C105 L111 -T2 2.2 68k 56k 3.3k 4.7µH 120p
10nH 100p 1.1V 10nH G2 D FT103 R144
R141
IC102
SET 6 243.95MHZ Q105 6.8k 330 IC101
G1 S SAW 3SK254 TA31161FN
LCD501 L104 L117
FM RF IN
AM RF IN
KEY+ 7 2 3 4 5 G2 D -T2 Q107 (EL)
OSC OUT
MIX OUT
REG OUT
DET GND
LCD 12nH 68nH
OSC IN
FE OUT
FE GND
FM OSC
AM OSC
DISCRI
R114 R116 L106 2SC4738
IF IN
FM RF
R111 22nH C115 1.8V 10
GND1
VCC1
KEY- 8 68k 33k 1k 2p
DEC
AFC
G1 S
BS
NC
1 2 3 4 5 6 7 8 9 10 11 12 G2 D C128 2.4V
R104
R101
82k
N.C. 9 1k Q101 0.8V 3p 1.1V 0.3V
COM2 COM3 L107 C119 G1 S 1 2 3 4 5 6 7 8 12 11 10 9 8 7 6 5 4 3 2 1
SEG19 C102 3SK299 22nH 5p Q106 1.1V
SEG19 10 220p L102 1V G2 -T1 0.3V 1.5V 3SK254 0.5V
D
SEG18 12nH -T2 G2 D 2.8V 2V 3.3V 1.2V 1.3V 3.6V
SEG18 11 Q102 3.3V
Q104
R122 36k
R125 91k
R133 33k
C129 18p
SEG17 G1 S 3SK255 G1 S R142 R145 FT107
SEG17 12 1V 3.3V -T2 G2 D C130 3SK255 C138 330 1V 10 10.7MHZ
0.01 -T2 0.047 0.4V 3.3V
R102 10k
R106 120
SEG16 CF
SEG16 13
RSSI A
R113 G1 S
0.047
R105
C141
L115 C146 C147 C158 C159
R135
R146
SEG15
47k
150
22
SEG15 14 L101 33k C113 C114 R127 100nH C133 C136 R139 0.047 0.047 0.01 10 R148
12nH 0.001 0.001 33 0.001 0.01 120 B B B 10V 150
SEG14
COM1 COM0 SEG14 15
SEG13 C103 C104 C106 C107 C108 C111 R112 L108 C123 C118 C116 C126 C125 L116 C131 C137 FT104 R143 C142 C148 FT105
13 14 15 16 17 18 19 20 21 22 23 24 SEG13 16 220p 0.001 220p 0.001 nm 220p 22k 6.8nH 0.001 9p nm 0.001 0.001 100nH 0.001 0.01 10.7MHZ 3.3k 0.047 0.047 10.7MHZ
CF B CF
SEG12
SEG12 17
SEG11 TO CN501/ 2ND FREQ
2 SEG10
SEG11
SEG10
18
19
MB-2 BOARD
L304
10nH
C318 3.3V
SEG9 2p IC302 PLL IC
SEG9 20
PLL_LD
LMX2331 3.3V
SEG8 R311 1k R320
SEG8 21 C314 SK/CLK Q306 1k
10
11
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
COM0
12
SEG6
9
GND DATA 3.3V
SEG6 23 2.7V 6.8k
1.7V R313 1k
SEG5 JR301 PLL_LE Q304 3.3V
1'st VCO L302
13
8
LED SEG5 24 6.8nH 0 X-IN PLL LE
C4915
C328 R321 L312 C337
SEG4 220p 1.2k 27nH 10p C340 R331 L315
SEG4 25 Q301 CP301 33p 47 68nH
14
7
GND GND
SEG3 2SC4738 C311 C313 R306 C320 R336
SEG3 26 220p 2p 100 C319 100p 6.8k
3.3V 2.6V B CK 100p 1.1V
15
6
SEG2 F-IN1- F-IN2- R319 C324 Q305
3 2 1
4 5 6
SEG2 27 VCC OUT 1.5V 150 2.1V
D13 L303 6.8nH 1.6V 5p C4915 3.3V
SEG1 C341 R332
16
5
SML- RF INDICATOR SEG1 28 GND GND F-IN1 F-IN2 Q302 33p 47 0.4V
R305 C4726LN
310MTT86 SEG0 3.3V VC MOD C315
220p 100 JR302
0
1.5V R322
2.7k 1.4V
SEG0 29
17
4
GND GND Q303
R307 B R317 R318 C331 L308
COM3 1k 1.4V 1k 10k 100p 56nH C4726LN
R13 COM3 30
18
3
CP1 CP2 C339
470 COM2 R303 3.3V 0.9V 10 1.2V
COM2 31 R302 1k R304 C316 3.3V C325 0.9V C335 10V 1.2V
1k 1k C317 2.2 18p
19
2
COM1 5p 2p VP1 VP2
16V CH
COM1 32 R314 R315
C304 22 0.3V
COM0 22
20
1
COM0 33 0.01 Vcc1 Vcc2
C302 C303 B C305 C306 C307 C312 C308 L305 C321 C327 R316 C326 C332 C334 R323 C336 C338 R334 R337 L316 C347
100 10 0.001 0.01 4.7 3p 1 47 C322 3.2V 0.33 0.01 100 4.7k 100nH
10V 10V B B 16V CJ 6.3V 10nH 10V 100p C323 10V 560 B 12p 0.001 2.2k 18p 10V 4.7k 0.01
3.3V 34 100p
GND
GND 35 D301 R324 C333 C342 R335 C346 C343 C344 R338 C345
R27 R26 R25 HVU358B 0.001 0.01 62 10p 0.01 62 10p
1ST FREQ
R31 R32 R33 150 0.01 CH CH
10k 1k 10k 1k 10k 1k 243.25MHZ
4MHZ 4MHZ
3 S1
TACT SW
C35
0.01 S2 C36
0.01
S3
TACT SW
C37
0.01
RF IN (B)
1'st MIX L212 L221
3.3V
IF-DET
C245
DISCRI C253 C254 C255 C256 C257 C260
B TACT SW B B
DP-1 BPF L205 R221 R224
0µH
R228 L213
0µH
2'nd MIX
C248
C244
0.047
0.1
B
C251 C252
4.7 1
16V 6.3V
10 0.047 22 0.1
10V B 16V 10V
L224
L200 100nH
C201 0µH 68k 68k NM 220nH 0.047 C243 B L223 0.01 0.01 47µH
R232
68k
4.7µH
SET +KEY -KEY 0.001 47µH B
L222
220p R234 C234 B
56k 68p
0.001
C233
R238 3.3k
FT202 R241 R244
L214 C227 6.8k 330
100nH 3p 1.3V
RF AMP 1V 3.3V 1V 1.4V 1.2V 6V
6 7 8 1
5 4 3 2
R205 3.2V C235
FT201 22 R229 FT203 120p
2.2 R230 243.95MHZ 13 14 15 16 17 18 19 20 21 22 23 24
1 8 7 6 2.2 SAW 3.3V 2.4V 16 15 14 13 12 11 10 9
C217 L211 G2 D
L217 G2 D
FT204 Q207
METER
220p 10nH 68nH Q205 10.7MHZ
VCC
BAND SEL
AM IF IN
FM IF IN
AFC/AGC2
AFC/AGC1
DET CONT
2SC4738
IF GND
FILTER
RIPPLE
GND2
MIX IN
IF OUT2
IF OUT1
AM IF OUT
QUAD
CXA1611N-T4
DET OUT
10 CF
RSSI
VCC2
3SK254
AF OUT
L203 C205 R247
10nH G1 S Q203 G1 S -T2
100p C228 220
IC202
1.1V 3SK255 1.1V
3p
-T2 0.3V 1.1V IC201
FM RF IN
AM RF IN
2 3 4 5 L204 0.5V TA31161FN 2.4V 1.3V
REG OUT
DET GND
0.3V
FE OUT
FE GND
FM OSC
AM OSC
DISCRI
R204 12nH G2 D
OSC OUT
MIX OUT
R216
(EL)
FM RF
OSC IN
1k
1k R211 R214 L206
IF IN
AFC
1.8V
GND1
VCC1
68k 33k 22nH
NC
DEC
0.8V
1.5V G1 S
BS
8.9V G2 D R242 R245
R201
82k
330 10
Q201 L207 C215 C219 Q206 FT206 12 11 10 9 8 7 6 5 4 3 2 1
G1 S 1 2 3 4 5 6 7 8 10.7MHZ
C202
3SK299 22nH 2p 5p 3SK254 1V 0.4V
CF
220p L202 1V
G2 D
-T1 Q204 -T2 1.3V 3.6V
12nH 2.8V 2V 3.3V 3.3V
3SK255
C230 0.01
-T2 C242
4MHZ
G1 S R213 G2 D C241 0.047 FT207
1V 33k 0.047 B 3.3V 10.7MHZ
R225 91k
CF
R202 10k
R206 120
R222 36k
R227 33
G1
6.8nH
100nH
100nH
S
0.001
0.001
0.001
0.001
0.001
L208
L215
L216
C218
C216
C214
C223
C225
C226
C231
C246 C247 1.2V R248
9p
nm
L201 3.3V R235 C236 C238 R243 C259
12nH C213 47k 0.01 0.047 3.3k 0.047 0.047 10 150
0.001 B B 10V
C204 C206 C207 C208 Q202 R233 C229 R239 C237 R246 C258
C203 0.001 220p 0.001 nm C211 R212 33k 18p 120 0.01 150 FT205 0.01
220p 220p 22k 3SK255 10.7MHZ
4 -T2 CF B
A B C D E F G H
DP-1, MB-2 DP-1, MB-2
DIVERSITY S/W
1
IC401
TC74HC4053AFS-EL
R411 EXPANDER
1.2V
56k
1.2V
8 7 6 5 4 3 2 1 DE-EMPASIS LPF 6V
IN NF 3V
R414 8 VCC 1
EN
0Z
1Z
0Y
1Y
GND
VEE
3.9k
ZCOM
XCOM
YCOM
2.7V IN SUM
VCC
3V
0X
1X
C406 SUM
A
0.0033 6V 7 60K
2 CN2 10P
8
9 10 11 12 13 14 15 16 C413 CELL GAIN ANT-A 1
R410 2.7V 4.7 16V 3V 20K 3V F
15k CONT
RF GND 2
7
3.3V 1.2V 1.2V 3.3V 6 IN
REFERENCE 3
C404 IC402 REF C416 AF OUT 3
4.7 R409 C NJM2100V RECTIFIER CAP 10
16V 15k E 20K M/S DATA
6
10V AF GND 4
2.7V D C408 ADDRESS
5 4 M/S_ADDRESS 5
R401 100k
R402 100k
R403 100k
R404 100k
0.0027 RECT GND
5
CAP
R406 56k
R415 +B 6
R412 47k
R153 R253 R405 3.9k
1k IC403
C405 10 10V
1k 1k TP4 D901 GND 7
DIV TK10691M 1SS355 MS_DATA 8
C163 C401 C403 C407 C415
4.7 C263 R408 C402 4.7 10 0.001 1 RF GND 9
16V 4.7 1k 0.1 16V 10V B 16V
16V ANT-B 10
AFM
R407 C409 C417
22 C414
AFM
DIV
TONE
R442 C433
C162 RV101 47k 4.7
10 R152 2.2k 1.2V C423 R423
R421
56k
16V
10V 3.3k C161 0.1 100k R436 R435
100p B 10k 560k
A R151 2.7V
IC15 IC16
BA033FP -E2 BA17806 FP
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG0
COM3
COM2
COM1
COM0
X402 R424
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
10k 32.0KHz 100k C429 0.1
3.3V 6V 9V
B AMP
R901 22k
C424 R434 3 1 3 1
15p X401 2.2k
D401
4 3 2 1 32.0KHz MA133-TX IC406 2 2
NJM4580V
C56 C55 C54 C57 C58
2.8V 6V
100 0.1 0.1 0.1 0.1 CN501 35P
IC103 C432 R445 10V
1
8
R426 C428 R433 C53 C51
10k 0.1 100k 100 100 GND 2
2
7
R431 3.3V 3
33k R444 3.3V
3
6
A R251 2.8V R432 C427 22 2.3V LED RF
B LED 5
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
10k 1k 0.1 R440 4.5V 16V R19 R29
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
4
5
SET 6
64 63 62 61
R443 SEG0 40 KEY +
R427 IC405 10k 5 4 KEY+ 7
2.2k NJM2100V COM3 39 R18 KEY -
3.3V G VCC KEY- 8
C262 R252 C261 C436 COM2 38 1.3V
10k IC13 L12
10 3.3k RV201100p 0.1 15nH N.C. 9
10V 2.2k C426 C425 R425 C422 R422 C421 R441 C431 B DIV DIV COM1 37
TC4SU69F
C166 470p 0.1 3.9k 1 IC11 (TE85L) SEG19
SEG19 10
0.1 6.3V 47k 0.1 56k 10
16V AT24C64N-10SI AMUTE
65 AFM COM0 36 R17
B 10k NC GND SEG18
CS 0.3V
SEG18 11
ALO 3.3V 66 CS VLC1 35 1 2 3 SEG17
AF LEVEL ADJ. EEP_DI/DO SK/CLK SEG17 12
1 2 3 4
8 7 6 5
R452 NOISE R451 10k R466 R465 GND SDA 67 SK/CLK VLC2 34 R21 10 SEG16
560k 10k 560k SK/CLK PLL_DATA R16 SEG16 13
A2 SCL R12 68 PLL_DATA VLC3 33 0V 3.3k C25 C29 R20 SEG15
10k CS PLL_LE 0.01 0.01 10 SEG15 14
A1 WP 69 PLL_LE IC10 VL 32 B 1.4V SEG14
C441
0.1
R453
2.2k
R464
2.2k
C445
0.1 A0 VCC
C11 0.01 B
3.3V
70 VDD CXP83516 VSS 31
C28 5p 50V B
SEG13
SEG14
SEG13
15
16
3
71 XTAL 30 SEG12
SEG12 17
D402 72 EXTAL 29 C21 R30 R22 CT11
SEG11 TO CN502/
D403 MA133-TX C34 0.01 B C10 100 10V 0.01 B RESET 1M 330 X11 20p
4MHz SGE11 18
MA133-TX 73 RST 28 C18 SEG10 DP-1 BOARD
C472 EEPROM 0.01 B NOISE SEG10 19
2.2 74 NOISE 27 C17 C27 SEG9
C446 R463 0.01 B TONE R15 27p SEG9 20
R454 R455 C443 3.3V 2.2 100k 75 TONE 26 C16 10k 50V SEG8
100k 3.9k 0.1 1.5V 16V TEST 0.01 B ALO SEG8 21
76 TEST ALO 25 SEG7
1
+KEY SEG7 22
21 22 23 24
R457 77 +KEY SEL Q51 SEG6
10k C448 -KEY C20 2SA1832 SEG6 23
2
78 0V
XC61FN2712MR
P_OFF_ IN
EEP_DI/DO
0.1
3
M/S_DATA
SEG4 25
IC12
RSSI_B R55
80
PLL_LD
LED_RF
R461 R462 RSSI SEG3
3
MMUTE
MATT0
MATT1
MATT2
MATT3
MATT4
C442 1.5V 1.6V 2.2k R10 B 10k SEG3 26
RSSI
470p 33k 10k C19 C30
MPS
RXD
TXD
4
A
RESET SEG2 27
1
B
R481
56k
1.4V SEG1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 R34 SEG1 28
3.3V
SEG0
2
56k SEG0 29
C449 C462 C33 C39 R35 100k C15 R56 R57
0.1 0.1 COM3
B 10 B 0.1 0.01 2.7k 4.7k COM3 30
10V COM2
COM2 31
COM1
COM1 32
EEP_DI/DO
R482
M/S_DATA
47k C12 C13 COM0
0.01 COM0 33
PLL_LD
LED_RF
RSSI_A
B 0.01
B 3.3V 34
R36
10k GND 35
TEST
RSSI B
R28
10k
R23
10k
R24
10k
4
TP3 TEST
TP1 TXD
TP2 RXD
MB-2
U6264 U6668/AU66 CE62/J CE67
[dBm]
L101
-20 12nH 12nH 12nH 10nH
L201
L102
15nH 12nH 12nH 12nH
-27 -28 -28 AUDIO OUT L202
-29 G -28dBm L103
15nH 10nH 10nH 10nH
L203
L104
12nH 12nH 12nH 10nH
-37 L204
-36 L111
12nH 10nH 10nH 10nH
-40 L211
A B C D E F G
MB-2
LEVEL DIAGRAM BOARD NO. 1-687-303-12
7-4. URX-P1 A1
CN101
0P FT103
243.95MHZ
SAW
L113
1 C101
220p
R105
22
L112
220nH 10
FT102 0µH L114 C127
R121 R124 100nH 3p
L105 68k 68k 3.2V
0µH
6 7 8 1
5 4 3 2
FT101 Q103 R129
2.2
R130
2.2
3SK255
COM1
COM2
1 8 7 6 C117
COM1 COM2 220p -T2 G2 D
13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4 5 6 7 8 9 10 11 12
SEG10 SEG0 L103 0.3V
33nH G1 S
L111 1V
SEG11 SEG1 10nH
SEG12 SEG2
R104
C105
L104
27nH
2 3 4 5
1k
220p R111 R114 R116 L106
SEG13 SEG3 47nH C115
68k 15k 1k 1p 1.6V
SEG14 SEG4 G2 D
SEG15 R101 3.1V Q101
SEG5 3.3V L107 C119 G1 S
68k 3SK299 27nH 220p
SEG16 SEG6 C102 1V -T1 Q104
220p L102 G2 D
SEG17 SEG7 18nH 3SK255
G1
-T2
SEG18 SEG8 S 2.7V
C130
L115 100nH
0.8V G2 D
SEG19 1V 0.01
SEG9
R125 68k
R102 30k
R106 120
R100 1k
0.001
G1
C125
2.7nH
S
0.001
0.001
0.001
0.001
0.001
COM0 COM3
C111
220p
L108
C108
R127
C104
C107
C113
C123
C126
R113
R112
R115
R122
C106
220p
COM0
COM3
22k
68k
27k
nm
33
L101 33k C114 C118 C116 L116
15nH 0.001 6p nm 100nH
PLL_LD
R20 L304 C318
10
TC4SU69F(TE85L)
10nH 3p
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG0
COM3
COM2
COM1
COM0
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
L12 IC302
15nH C314 LMX2331
IC13
5p
R29 R311 1k SK/CLK
R19 3.2V
10
11
10 3.2V PLL LD CLK
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 10k R312
2.3V JR301 3.28V 1k PLL_DATA
L302
12
9
1.7V 0 GND DATA
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
6.8nH
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
IC11 1.7V R313
AT24C64N-10SI 5 4 Q301 1k PLL_LE
64 63 62 61
R18 C311
13
8
SEG0 40 10k VCC
2SC4738 220p C313 R306 X-IN PLL LE
CP301 B 2p 100 C328
EEP_DI/DO COM3 39 1.3V 3.3V 2.6V CK 220p
14
1 2 3 4
8 7 6 5
7
GND SDA GND GND
3 2 1
4 5 6
SK/CLK COM2 38 VCC OUT C319 C320
A2 SCL R12 DIV R17 L303 100p 100p
15
6
10k CS DIV COM1 37 10k C29 NC GND GND GND 6.8nH JR302 F-IN1- F-IN2-
A1 WP AMUTE 0.01 0 1.5V 1.5V
65 AFM COM0 36 0.3V B 1 2 3 VC MOD
16
5
A0 VCC CS 3.3V F-IN1 F-IN2
66 CS VLC1 35 C315 R305 1.5V 1.5V
1.5V
SK/CLK R16 R21 220p 100
17
4
67 SK/CLK VLC2 34 3.3k 10 R307 B GND GND
PLL_DATA C25 C28 1k 1.4V C316
C34 68 PLL_DATA VLC3 33 0V 0.01 5p 5p 1.8V
18
3
PLL_LE B CP1 CP2
0.01 69 PLL_LE IC10 VL 32 50V
R308 10
B R302 R303 R304 3.3V
CXP83516 1k 1k 1k
19
2
70 VDD VSS 31 VP1 VP2
R314
C11 R22 330 R315
22
C10 0.01 71 XTAL 30 CT11 C317 22
100 20p C305 3p
20
1
B Vcc1 Vcc2
10V 72 EXTAL 29 R30 X11 C302 C303 0.001 C306 C307 C312 C308 L305
C19 1M 4MHz 100 10 B 0.01 4.7 3p 1 10nH C323
73 28 0.01 B RESET 10V 10V CJ 6.3V
XC61FN2712MR
RST B 100p
R10 C18 C27
0.01 B NOISE C20
3
10k 74 NOISE 27 C17 0.01 27p C304 C321
50V 47 C322
IC12
21 22 23 24
2
77 +KEY SEL
A2
-KEY
78 -KEY M/S_ADDRESS
C15 3.3V
10
C33 C39 SET_KEY 0.01 B BAT0 CN201 R205
0.1 B 0.1 79 SET_KEY BAT0 0P 22 L213 L214
P_OFF_ IN
EEP_DI/DO
L212 C227
M/S_DATA
RSSI_B 0µH R221 R224 220nH 100nH 3p
80
PLL_LD
LED_RF
RSSI 68k 68k
MMUTE
MATT0
MATT1
MATT2
MATT3
MATT4
B 3.2V
RSSI
C14
MPS
RXD
TXD
6 7 8 1
5 4 3 2
243.95MHZ
0.01 B L203
A
33nH R229
FT203
D13
SAW
SML-
C201 2.2 Q203
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 220p R204 C217 L211 3SK255
310MTT86 1k 220p 1V 10nH G2 D -T2
C205
0.01 B
C13 1 8 7 6 220p G1 S 0.3V
LED_RF
C12
0.01 B L205
R13 FT202 0µH
470 FT201 R230
Q54 2.2
DTC124EE
R214
15k
L204 L206
EEP_DI/DO
27nH R211 R216 47nH 1.6V
2 3 4 5 68k 1k
PLL_LD
LED_RF
RSSI_A
G2 D
MMUTE
MATT0
MATT1
MATT2
MATT3
MATT4
R50 Q201
MPS
47k R201 3.1V 3SK299 L207 C215 C219 G1 S
68k 1V -T1 27nH 1p 220p
L202 G2 D
3.3V Q204
C207 0.001
3SK255
C230 0.01
C202 18nH
BAT0
-T2
TEST
220p 2.7V
C208 nm
G1 S 1V R213 G2 D
2.7nH
+KEY
-KEY
R28 R23 R24 33k
0.001
L208
C214
C206
220p
SET_KEY
10k 10k 10k
R222
R202 30k
R206 120
R225 68k
R200 1k
27k
C218
C203
6p
G1
100nH
100nH
TP1 TEST 220p S
0.001
L215
L216
C204
L201 C211 R212 0.8V C216 C226
TP2 TXD 15nH 220p 22k R215 nm 0.001
Q52 68k
FMM717TA TP3 RXD
D2 C213 Q202 C223 C225 R227
UMZ8.2T 0.001 0.001 0.001 33
-T106 S4 2.9V 2.9V 2.9V 3SK255
2P2S -T2
4 L1
47µH
0.6V D1
R60 C5-K3L MA2Z748
100k 2.2V
XP151A13A0MR
5 4
R53
Q51 220 C52
EXT GND
2SC4738
Q1
TACT SW
TACT SW
TACT SW
IC1 1k 1k 1k
S1
S3
R54 XC6367A331MR
S2
15k R55
47k
0.7V
C56 C35 C36 C37
C62 R52 C51 C54 R56 C53 C55 100 C57 C61 C59 C60 0.01 0.01 0.01
100 2.2k 10 100 47k 0.1 1 10V 0.1 0.01 1 100 B B B
10V 10V 10V B 6.3V B B 6.3V 10V
A B C D E F G H
MB-1 MB-1
3.3V
C156
0.047
B 1
R141 R144
L121 6.8k 330 C152
0µH C145 C143 C151 C154 C155 C157 C160
0.1 0.001 C144 L123 0.01 0.01 1 10 22 L124 0.1
B 0.047 47µH B B
C153 6.3V 10V 10V 47µH 10V 1.2V 1.2V
B 4.7
TC74HC4053AFS-EL
10V
1.3V 8 7 6 5 4 3 2 1
2.2V 1V 1.4V 1.2V 2.9V 3.3V
EN
0Z
1Z
0Y
1Y
GND
VEE
ZCOM
IC401
16 15 14 13 12 11 10 9 13 14 15 16 17 18 19 20 21 22 23 24
Q107 2.4V
XCOM
YCOM
C134 FT104 2SC4738
VCC
GND2
MIX IN
0X
1X
IF OUT2
IF OUT1
QUAD
METER
68p 10.7MHZ
VCC
RSSI
VCC2
A
BAND SEL
AM IF IN
FM IF IN
AFC/AGC2
AFC/AGC1
DET CONT
AF OUT
IF GND
FILTER
RIPPLE
AM IF OUT
DET OUT
CF
CXA1611N-T4
4.7µH
3.3V
L122
R415 3.9k
3.3k C135 220 56k R414 8 VCC 1
IC102
120p IC101 3.9k C408
1.1V 3.V 1.2V 1.2V 0.0027
R132 R134 TA31161FN 1.2V
0.0033
FM RF IN
AM RF IN
3.3V 0.4V (EL) F
C406
OSC OUT
MIX OUT
REG OUT
DET GND
68k 56k 2.4V 1.3V 1.5V IN SUM
OSC IN
FE OUT
FE GND
FM OSC
AM OSC
DISCRI
G2 D SUM
IF IN
FM RF
Q105 2
GND1
VCC1
3.3V 7
DEC
AFC
3SK254 60K
BS
NC
C404
8
G1 S -T2 1.6V
C128 L117 1V 4.7 CELL GAIN
3p 82nH 0.4V 1 2 3 4 5 6 7 10V 3.3V R409 R410 1.5V 1.6V 20K 1.6V
8 FT106 12 11 10 9 8 7 6 5 4 3 2 1 15k 15k CONT
7
10.7MHZ R153 6 IN
REFERENCE 3
IC402
R402 100k
R403 100k
R404 100k
1.5V 1.2V 2.5V 1.5V REF
G2 D 3.3V CF 1k C NJM2100V C413
4.7 E 20K
RECTIFIER CAP C416
6
3.3V 10
TP4 10V
C409 0.1
Q106G1 S
R142
330
R145
10 FT107 DIV R405
1k
R406
56k
D 5 RECT 4
10V
3.3V GND
5
3SK254 10.7MHZ CAP
1.2V CF
-T2 C163
0.047
R401
0.001
0.047
C148
C131
C141
FT105 C146 C147 C158 C159 4.7 R408 C405 C407 C415
R146
IC403
150
C133 R143 10.7MHZ 0.047 0.047 0.01 10 R148 10V R253 1k 100k C402 C401 R407 R412 10 1.5V 0.001 1
0.001 3.3k CF B B B 10V 150 1k 0.1 4.7 33k 47k 10V B 16V TK10691M
R133 R135 C136 R139 C137 C138 C142 C263 C403 C417 C414
RSSI A
33k 47k 0.01 120 0.01 0.047 0.047
B 4.7 10 22 0.1
2
AFM
DIV
2ND FREQ 10V 10V 10V
AFM
Q306
TONE
2SC4738 C423 R421
3.3V R423 56k
0.1 100k R436
10k R435
L313 L314 C166 560k
R320 R333 68nH 100nH 0.1 R424 R441 R442
6.8k 3.3V X402 NM 22k
1k 32.0KHz 100k C434 R448
3.3V 22 680 R445
Q304 1.1V R251 560
2.6V 3.3V 10k C424 C429 10V
1
R319 C324 R321
1.2k L312 C337
10p
C4915
R336 L315 15p X401
32.0KHz
R434
2.2k 0.1 G R416 R447
B
150 5p 27nH 6.8k 68nH 1.6V 56k 3.3k
D401
2
3.3V MA133-TX 3.3V
2.6V C161 R151 IC103 C261
B
C340 R331 1.1V 3.3V
8
2V 33p 47 100p 10k NJM2100V 100p 1.5V
R444
6
3
R433 C465 1.5V
RV201
0
1
8
2.2k
100p
A
1.2V 100k
7
Q302 1.1V R426 1.5V 1.5V C428 R400 C432 IC406
4
R322 C4726LN Q305 10k 0.1 22k nm NJM2115V R419 Q402
7
2.7k 1.4V C4915 IC405 10k
6
R318 C331 L308 Q303 1.5V R431 UN2225
R317 RV101 NJM2100V 33k
10k 100p 56nH C4726LN 1.6V 1.5V
6
1k 2.2k
5
R443
0.4V R252 1.5V R432 C427 NM
C335 C341 R332 R152 R427 1k 0.1 R418 Q405
5
C325 0.9V 0.9V C338 0.4V 3.9k
2.2 18p 100 33p 47 3.9k 2.2k R420 100k UN2225
CH
HVU358B
3300p
C162
C433
10 10 C422 C431
C426
470p
C327 R316 C326 C332 R323 C336 R324 C339 R334 C342 C346 C343 R337 C344 R338 C345 C347 L316 10V C425 1 C421 nm C464 C438
0.33 0.01 10 10p 10p 10V 10 R417 R446
10V 560 B 12p 2.2k 18p 150 10V 4.7k 0.01 0.01 CH 4.7k 0.01 62 CH 0.01 100nH 0.1 6.3V 0.1 10V 47k 0.1 390
B
GND
C334 C333 R335 R422 C436 C437
0.001 0.001 62 47k 0.1 22
B 10V
2ND FREQ
4MHZ 3
3.3V C472
C245 2.2
L221 0.1 C253 C254
1
C255 C256
10 0.047
C260
0.1
16V 1.6V
0µH B 4.7
10V 6.3V 10V B 10V
R481 C471
1.6V 2.2 16V
R466 R465 6.2k
0.047
C244
16
2.2k
1
R453 VCC IN4
16 15 14 13 12 11 10 9 13 14 15 16 17 18 19 20 21 22 23 24 C441 2.2k R485
C234 0.1 D402 390 1.6V
MA133-TX
15
D403
2
GND2
MIX IN
IF OUT2
IF OUT1
R238
3.3k
QUAD
L222
METER
R486
VCC
RSSI
VCC2
BAND SEL
AM IF IN
FM IF IN
AFC/AGC2
AFC/AGC1
DET CONT
MA133-TX
AF OUT
IF GND
FILTER
RIPPLE
AM IF OUT
CXA1611N-T4
DET OUT
180 1.6V
14
C235 R244
3
R241 R247 IN1 COM
330
IC202
120p 6.8k 220 R454 R487 1.6V
13
3.3V 100k R425 100
4
IN0 IN7
2.4V 3.9k
FM RF IN
AM RF IN
MIX OUT
REG OUT
DET GND
2.4V 1.3V C446 R463
OSC IN
FE OUT
FE GND
FM OSC
AM OSC
12
IF IN
FM RF
5
Q205
GND1
VCC1
AFC
3.9k 6P
BS
NC
3SK254 OUT
8
-T2
11
6
G1 S C444 R457 1.5V A EN
C228 L217 1 2 3 4 5 6 7 8 FT206 12 11 10 9 8 7 6 5 4 3 2 1 0.1 10k
R490 10k
3p 82nH C448
R489 10k
C461 0.1
2
7
1.1V 10.7MHZ
2
10
0.4V IC407 C447 10
7
1.5V 0.4V CF 1.2V 2.5V R456 B VEE
1.5V 47p 10V
3.3V 10k NJM2100V
3
G2 D 3.3V 3.3V
R491 10k
3
6
1.2V R497
8
R461 R462 C GND
4
Q206 G1 S R242 R245 C442 33k 470 100k 1 6
3SK254 330 10 FT207 470p
5
2 5
-T2 10.7MHZ 3 4
CF J401
0.001
0.047
0.047
6
C231
C238
C248
R246
C237
0.01
120
150
L451
L452
0µH
0µH
(EL) B B 150 B 10V AFT(EL)
JR402
0
FT204 R243 C241 C242 FT205
RSSI B
MATT2
MATT3
MATT4
10.7MHZ 3.3k 0.047 0.047 10.7MHZ
CF B CF
MPS
MATT1
MATT0
MMUTE
4MHZ
Q403 Q404
DTA114EE 0V 0V DTA114EE
IC410
C475 TC4HC4051
2.2 AFT(EL) 3.3V
16V 3.3
U6264/CN U6668/AU66 CE62/J CE67 KR 3.3V
[dBm]
16
3.3V
1
VCC IN4
-20 L101 1.6V
15
10
C451 P/ MT C457
1
L201 18nH 15nH 15nH 12nH 15nH R492 IN2 IN6
2.2 R471 SW /SW 100
1k 1.6V 1.6V 16V 2.2k 10V
14
L102
9
IN1 COM IN OUT1
-27.5 -28.5 L202 22nH 18nH 18nH 15nH 18nH R493
-29 1k 1.6V
13
R470 C458
8
IN0 IN7 GND GND
L104 R494 1.6V
100k R472 100
-29.5 33nH 27nH 27nH 27nH 33nH 8.2k 1.6V 2.2k 10V
12
L204
7
IN3 IN5 IN2 OUT2
L111
-37
11
6
L211 10nH 10nH 10nH 8.2nH 12nH A EN REF VCC
R495 10k
10
-40 L304
-40.5 12nH 10nH 10nH 10nH 12nH
B VEE 7 IC408
LA4534M
-42 L305 R496 10k R475
4.7
R476
4.7 5
9
A B C D E F G H FT101
102
201
6281 6291 6301 6321 6271 MB-1
LEVEL DIAGRAM 202 BOARD NO. 1-687-302-12
CP301 D38A D39A D36A
7-5. URX-R1
1
MB-3(1/2) 2'nd MIX IF-DET
A1 ANT B BPF FT102
ANT 3.3V C144
3.3V
CN101 1'st MIX 0.047
6 7 8 1
5 4 3 2
0P CN102 B
L121 C145
4.7µH
L112 R124 IC101
L122
C117 0µH R121 68k L113 R132 R134 R138 C134 0µH R141 R144 C143 0.1 L123
220p 68k 220nH 68k 56k 3.3k 68p 6.8k 330 TA31161FN 0.001 B 47µH
(EL)
C101 7.9V L114 C127
2
220p RF AMP 100nH 3p
2.2V
R129 3.2V
L103 C105 2.2
1 8 7 6 47nH 100p C135 16 15 14 13 12 11 10 9
L111 Q103 120p
10nH 3SK255
GND2
MIX IN
IF OUT2
IF OUT1
QUAD
R104
1608
R101
220k
RSSI
VCC2
D -T2
AF OUT
1k
FT101 L104 1.1V G2 FT103
27nH L105 243.95MHZ Q107 2.4V
0µH
G1 R130 SAW L117 Q105 2SC4738
S G2 D
2.2 68nH 3SK254 FT104
2 3 4 5 7.8V
G1
-T2 10.7MHZ
R111 R114 R116 L106 C115 1.1V S CF
OSC OUT
MIX OUT
C128
OSC IN
68k 33k 1k 22nH 2p 1.8V
IF IN
R103 3p
GND1
VCC1
C102 33k G2 G2 D
DEC
220p 1.1V
BS
1V D
R147
220
0.5V
L107 C119 G1 S 1.8V
G1 S 3.3V
22nH 5p G2 D 1 2 3 4 5 6 7 8
L102 Q101 Q104
3SK255 -T2
0.4V
18nH R142 R145
3SK299 3SK255 330 10 FT105 3.3V
-T1 -T2 Q106 G1
Q102
3.2V S 10.7MHZ 3.3V
C130 0.01
R113 CF
C495 33p
R105 1V
0.8V
33k
G2 D 3SK254 0.4V
1V 0.4V
22 -T2 3.3V
2.4V 1.3V
G1 S
2 0.8V
0.047
100nH
0.001
C148
L115
C133
R112 R127 C125 C138 R143 C146 C147
22k 33 0.001 0.01 3.3k 0.047 0.047
B B B
L101 C103 C104 C106 C111 C113 C114 C123 C118 C116 C126 C131 C129 C136 C137 C141 R146 C142
15nH 220p 0.001 220p 220p 0.001 0.001 0.001 6p 5p 0.001 0.001 18p 0.01 R139
120 0.01 0.047 150 0.047
FT106
RSSI A
R102 L108 R122 R125 B L116 R133 R135 B B B 10.7MHZ
C107 30k R106 C108 6.8nH 36k 91k 100nH 47k 68k 2ND FREQ CF
0.001 120 NM L304
10nH
3.3V
C318 3.3V
3p PLL IC IC302 R320 C339
CJ LMX2331LTMX 1k 10 2'nd BUFFER
C314 R353 2'nd VCO 10V
5p 270 Q306
PLL_LD R311 1k SK/CLK 3.3V
2SC4738
10
11
PLL LD CLK
R351 R312 1k 2.6V
1'st VCO L302 18 R352 PLL_DATA L314
12
9
GND DATA R333 L313
Q301 6.8nH 270 6.8k 68nH 3.3V
100nH
1.7V R313 1k
2SC4738 PLL_LE
13
8
X-IN PLL LE R321 L312 C337
C313 R306 C328 1.2k 27nH 10p
2.6V
CP301 2p 100 220p C324 2.6V 1.1V R336 L315
3.3V CK 5p 68nH
14
7
GND GND 6.8k
3 2 1
4 5 6
VCC OUT C319 3.3V
C311 R355 100p C320
L303 100p Q302 C340 R331 Q305
15
6
GND GND 220p F-IN1- F-IN2-
CH 6.8nH R354
18
270 R319
150
2V C4726LN 33p 47 C4915
3.3V
VC MOD
1.5V 1.5V Q304
R307 C4915
16
5
F-IN1 F-IN2
1k 1.4V
C315 R305 1.5V R322
220p 100 2.7k
Q303 1.4V
17
4
CH R356 GND GND
C331 L308 C4726LN C341 R332
R317 0.9V 1.1V
270 1.8V 1k 100p 56nH 33p 47
3
18
3
CP1 CP2
C347 0.01
R337 4.7k
R302 R303 R308 3.3V C325 R318 0.9V C335
1k 1k R304 C316 10 2.2 10k 18p
19
2
1k 5p VP1 VP2 0.2V 0.4V 0.4V
CH R314 R315 16V CH
22 22 TT
C305
20
1
Vcc1 Vcc2
C344
0.01
R338
0.001 C306 C312 C317 L305 C321 C326 C338
62
C303 C302 B 0.01 C307 3p 3p 10nH 47 R316 0.01 C332 C333 C334 R323 C336 R324 100 C346 C342 R335 L316
100 10 B 4.7 CJ CJ 10V C322 C323 560 B 12p 0.001 0.001 2.2k 18p 150 10V 0.01 0.01 62 100nH
10V 10V TT 100p 100p
C304 C308 C327 D301 R334 C343 C345
0.01 1 C497 0.33 HVU358B 4.7k 10p 10p
B 6.3V 33p 10V CH CH
(TO 2/2) 1 B B 2ND FREQ
1ST FREQ
4MHZ 2
ANT A A2
ANT 1'st BUFFER 3.3V
C245 0.1 B (TO 2/2)
CN201 CN202
0P L205 1'st MIX L212
C244
L206
22nH
RF AMP 0µH 0µH 2'nd MIX C243
R211 R216 3.3V L221 IF-DET 0.001 0.047 L223
68k 1k 0µH B 47µH
C201 R205 C215 R221 R224 C233 R241 R244
L207
22nH
220p
2 22 R214 2p 68k 68k L214 L213 0.001 6.8k 330
R247 220
33k CK 100nH 220nH
7.9V 0.8V
RSSI B
C219 R229 3.2V C227 R238 L222
C234 68p
3.3V 2.2 4.7µH 16 15 14 13 12 10 9
R213 3.2V 5p L211 3p 3.3k 2.4V 11
L203
47nH
R232
R234
Q207
68k
56k
33k G2 D 10nH CJ
Q203 2SC4738
GND2
MIX IN
IF OUT2
IF OUT1
G2 D
QUAD
FT201 C205 1608 1.1V
RSSI
VCC2
AF OUT
100p 3SK255 C235 FT204
1 8 7 6 G1 S 3.3V 10.7MHZ
R204 G1 S -T2 FT203 120p CF FT206
1k 243.95MHZ 10.7MHZ
0.001
0.001
C214
C223
6.8nH
C213 SAW FILTER L217
C211
220p
L208
0.001 R230 68nH G2 D Q205 1.1V
CF
L204 2.2
2.4V
3SK254
4 27nH 0.5V
1.8V
OSC OUT
MIX OUT
7.8V 1.3V
G1 -T2
OSC IN
G2 D S
IF IN
C228 1.1V
GND1
VCC1
R212 Q202 3p
DEC
2 3 4 5 R201 22k
BS
220k Q201 3SK255 G1 S CJ R242 R245
3SK299 -T2 330 10
C202 1V
R203 Q204 1.8V
G2 D 1 2 3 4 5 6 7 8
220p 33k G2 D
-T1 3SK255
6 7 8 1
5 4 3 2
-T2 G1 3.3V 3.3V
10.7MHZ
S
Q206
FT205
L202 G1 S 1V 3.3V
CF
C496 33p
18nH 3SK254
L215 100nH
C217 1.1V -T2
L216 100nH
0.4V 0.4V 1V 0.4V
220p
R202 30k
R206 120
R227 33
IC201 C246
L201 R222 R235 C236 C238 R243 TA31161FN 0.047 C247
15nH FT202 36k 68k 0.01 0.01 3.3k (EL) B 0.047
B B
C203 C204 C206 C207 C208 C218 R225 C216 C225 C226 C230 C231 R233 C229 R239 C237 C241 C242 C248
220p 0.001 220p 0.001 NM 6p 91k 5p 0.001 0.001 0.01 0.001 47k 18p 120 0.01 0.047 R246
150 0.047 0.047
B B B B B B
3
(TO 2/2)
A B C D E F G H
JK-1, MB-3 (1/2) JK-1, MB-3 (1/2)
DIVERSITY S/W
1
EN
0Z
1Z
0Y
1Y
GND
VEE
ZCOM
1.3V 2.9V 3.3V
0V 1V 1.4V 1.2V 47µH
XCOM
YCOM
VCC
13 14 15 16 17 18 19 20 21 22 23 24
0X
1X
C
A
3.3V IN NF
METER
VCC
BAND SEL
AM IF IN
FM IF IN
AFC/AGC2
AFC/AGC1
DET CONT
IF GND
FILTER
RIPPLE
9 10 11 12 13 14 15 16 8 VCC 1
AM IF OUT
CXA1611N-T4
DET OUT
R414 IN SUM
1.2V
C405 4.7k C408 SUM
R411 1.5V 0.0027 7 2
0.0033
FM RF IN
AM RF IN
60K
REG OUT
DET GND
56k C413
8
FE OUT
FE GND
FM OSC
AM OSC
DISCRI
FM RF
CONT
7
6 IN
REFERENCE 3
R410 IC402 REF
R403 100k
R404 100k
12 11 10 9 8 7 6 5 4 3 2 1 1.5V NJM2100V C416
R402 100k
15k 1.6V RECTIFIER CAP
20K 10
6
16V
R405
1.2V 1.2V 2.5V 1.5V
1k
C 4.7k C417 5 4
RECT GND
5
22
FT107
10.7MHZ
CF
TP4
DIV
C407
16V
CAP
IC403 2
D
R408
C158 C159 R401 C410 C415 TK10691M
33k
1k
0.01 10 R148 100k C423 C402 R412 10 0.001 1
B 10V 150 0.1 0.1 47k 10V 50V 16V
B B
AFM
DIV
10 4.7
10V 16V
TONE
AFM
RV101
2.2k B C163
R152 4.7 R436
C162 2.7k C161 25V R153 10k
10 100p 1k R423 R421
10V 100k 1.5V 56k R435
560k
A R151 3.3V
X402 C429 0.1 C433 TRS UNBALANCED OUT -30dBm
10k
D401 MA133
32KHz 4.7
1.2V 16V
R253 R424 R434 R441
5 6 7 8 1k 100k 2.2k 47k G
7V
C263 C472 C492 H
8
IC103 4.7 C424 X401 R447 47 22 L454
C432
0.01
NJM2100V 25V 15p 32KHz R433 150 16V
3.8V 50V 0µH
100k
7
3.3V C428 J402
0.1 3.7V 3.4V R444 R446 0P
8
1
4 3 2 1 15k 5.1k R458 OUT
6
R431 3.3k
33k R460 IC405
7
2
3
R459
100k NJM4580E
15k
IC404
5
C426 R426 NJM2100V R432 C427
A 0.001 10k 1k 0.1 3.8V R440
6
R251
10k 1.1V 50V 3 10k Q410
C262 B R427 UN2225
10 R252 RV201
5
R422
47k
C422 C430
C261
B C166
0.1 C421 C425
1.3V
1 R442
56k 10 C470
0.1
L455
0µH
100p 0.1 0.1 6.3V 16V
GND B
C431 C473
10 0.1
16V B
C254
C252 C253 1 C255 C256 C257 C260
4.7 6.3V 10 0.047 22 0.1
AFM
0.01 25V B 10V B 10V 16V
B XLR BALANCED OUT
C251 C478 MIC OUT -58dBm/LINE OUT -28dBm
0.01 L224 47
B 47µH 16V
C471 R482 33k C498 0.1 R490
nm 1.8k
1.3V 0V 1V 1.4V 1.1V 2.9V 3.3V C67 C476 Q407 S5
100 R483 47p R419 UN2225 2P2S
7V 16V 150 50V 150
13 14 15 16 17 18 19 20 21 22 23 24 R416
47k
3.8V 3.8V I
R491 J403
1
8
CN1
METER
R479 C477 56 0P
VCC
BAND SEL
AM IF IN
FM IF IN
AFC/AGC2
AFC/AGC1
DET CONT
IF GND
FILTER
RIPPLE
Q56 C480
AM IF OUT
3.8V
DET OUT
47p
3
2SC2712-YG 50V IC409 3.3k
2
7
NJM4580E C481
R486
IC410
33k
R481
2
IC202
JR401
7.7V 33k 22
3
50V
0
FM RF IN
AM RF IN
R492
4
REG OUT
DET GND
3.7V
56
3.8V R480 3.8V
FE OUT
FE GND
FM OSC
AM OSC
DISCRI
FM RF
R493
1.8k
12 11 10 9 8 7 6 5 4 3 2 1 R61 C479 22
3.3k R484 33k 47
Q408 50V
1.2V 1.2V 2.5V 16V UN2225
R485 R499 R498
FT207 33k 10k 10k
10.7MHZ
CF
C258
0.01
B
C259
10
10V
R248
150 C490
0.1
C482
0.1
C488 C485
47 10
16V 16V
C486 C487
10
16V 0.1
C489
0.1 JK-1
C475 R417 C493 C491
10 56k nm nm
16V
4 5 6 7 8 9 10
(TO 2/2)
JK-1
BOARD NO. 1-687-307-12
MB-3 (1/2)
BOARD NO. 1-687-305-12
3
1 2
(TO 1/2)
1
DP-2 LED
(TO 1/2)
EEPROM
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG0
COM3
COM2
COM1
COM0
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
CN502 35P CN501 35P RF INDICATOR
PLL_DI/DO
1 2 3 4
8 7 6 5
GND 1 1 GND GND SDA
COM2
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
COM3
A2 SK/CLK
GND 2 2 GND SCL R12
A1 WP 10k CS 1.7V
3.3V 3 3 3.3V
3.3V 4 4 3.3V A0 VCC R29
RF LED 10 R20
RF LED 5 5 RF LED 10
SET 6 6 SET SET IC11
AT24C64N-10SI R19
LCD501 KEY+ 7 7 KEY+ +KEY 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 10k L12
LCD 15nH
-KEY 2.3V 3.2V
KEY- 8 8 KEY-
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
1 2 3 4 5 6 7 8 9 10 11 12
N.C. 9 9 N.C.
64 63 62 61
COM2 COM3 SEG0 40 R18
TC4SU69F(TE85R)
COM0 COM0 10k
COM0 10 10 COM0 5 4
COM1 COM1 COM3 39 1.3V
COM1 11 11 COM1 VCC
COM2 COM2 COM2 38
IC13
COM2 12 12 COM2 C34 DIV R17
COM3 COM3 0.01 DIV COM1 37 10k C29
COM3 13 13 COM3 B AFM 0.01
SEG0 SEG0 65 AFM COM0 36 0.3V NC GND B
2 COM1 COM0
SEG1
SEG0
SEG1
14
15
14
15
SEG0
SEG1
SEG1
CS
SK/CLK
66 CS VLC1 35
R16
1 2 3
SEG2 SEG2 RESET 67 SK/CLK VLC2 34 3.3k 1.5V
13 14 15 16 17 18 19 20 21 22 23 24 SEG2 16 16 SEG2 PLL_DATA
SEG3 SEG3 68 PLL_DATA VLC3 33 0V C25 R21
SEG3 17 17 SEG3 IC12 PLL_LE 0.01 10 C28
SEG4 SEG4 XC61FN2712MR 69 PLL_LE IC10 VL 32 B 5p
SEG4 18 18 SEG4 CXP83516 50V
SEG5 SEG5 70 VDD VSS 31
SEG5 19 19 SEG5 C10 C11 R22 330 CT11
SEG6 SEG6 R10 100 0.01 71 XTAL 30 20p
SEG6 20 20 SEG6 10k 16V B R30 X11
SEG7 SEG7 72 EXTAL 29 C19 1M 4MHz C27
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
3
SEG7 21 21 SEG7 0.01 B RESET
COM1
COM0
73 RST 28 27p
SEG8 SEG8 C18 50V
SEG8 22 22 SEG8 RESET 0.01 B NOISE
1
SEG9 SEG9 74 NOISE 27 C17 R15
SEG9 23 23 SEG9 0.01 B TONE R14 1.7V 10k
SEG10 SEG10 75 TONE 26 C16 10k
2
SEG10 24 24 SEG10 C39 C33 TEST 0.01 B ALO
SEG11 SEG11 0.1 0.1 76 TEST ALO 25
SGE11 25 25 SGE11 +KEY
21 22 23 24
B B 77 +KEY SEL
SEG12 SEG12
SEG12 26 26 SEG12 -KEY C20
SEG13 SEG13 78 -KEY M/S_ADDRESS 0.01 B
SEG13 27 27 SEG13 SET_KEY
SEG14 SEG14 79 SET_KEY BAT0
PLL_DI/DO
P_OFF_IN
M/S_DATA
SEG14 28 28 SEG14 RSSI_B R56
80
PLL_LD
LED_RF
SEG15 SEG15 RSSI R55 2.7k
MMUTE
MATT0
MATT1
MATT2
MATT3
MATT4
SEG15 29 29 SEG15 B 10k
RSSI
MPS
RXD
TXD
SEG16 SEG16
A
R13 R27 R31 R26 R32 R25 R33 SEG16 30 30 SEG16 C14
470 10k 1k 10k 1k 10k 1k SEG17 SEG17 0.01 C15 Q54
SEG17 31 31 SEG17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 B 0.01 2SA1832
SEG18 SEG18
SEG18 32 32 SEG18
C37 SEG19 SEG19
C35 C36 0.01 SEG19 33 33 SEG19
0.01 0.01 B R58
3 D13 S1
B B 3.3V
GND
34
35
34
35
3.3V
GND C12
0.01
C31
1
4.7k
EEP_DI/DO
SML- TACT SW S2
SET TACT S3 B
310MTT86 SW +KEY TACT SW -KEY
C13
PLL_LD
LED_RF
RSSI_A
MMUTE
0.01
B
MPS
TEST
Q52
F51 S4 FMMT717TA
600mA 2P2S R60
100k Q55
IC1 IC2 DTC124EE
BA08T BA033T
8V 3.3V
J101 D2 LF901
0P XX XX R50 TP1 TEST NM
9V R53 C52 47k
3.3k 10 TP2 RXD NM
R51 16V
2.2k IN GND OUT IN GND OUT TP3 TXD NM
1 2 3 1 2 3
Q53 R28 R24 R23 C30
Q51 2SC4738F 10k 10k 10k 0.001
2SC4738F 50V
B
R54
15k
C62 R52 C51 C60 C63
4700 2.2k 10 R57 0.1 100
25V 16V 100k B 16V
4 C54 C55 C56 C57 C58 C59
100 0.1 0.1 100 100 0.1
16V B B 16V 16V B
A B C D E F G H
DP-2, MB-3 (2/2) DP-2, MB-3 (2/2)
(TO 1/2)
4 5 6 7 8 9 10
NOISE
MPS
MMUTE
0V
ALO
R452 R451
560k 10k R466
10k
R465
560k
C441 R453
0.1 D403 2.2k
MA133 R464 C445 MONITOR OUT
R425 2.2k 0.1
3.9k Q403 Q404 +-5kHz/Dev.16 0HM 5mW
DTA114EE DTA114EE
C450 D402
R454 MA133 3.8V
470p
10
100k C451 P/ MT C457
1
8
IC407 R463 2.2 R471 SW /SW 220 L451
4V
C443 NJM2100V 100k R448 35V 2.2k 1.1V 16V 0µH
R455
9
0.1 56k IC406 IN OUT1
3.9k C446 4V R494
3.8V NJM4558M
1
8
R456 R457 35V 47k GND GND 220
10k 10k 1.5V
4V 1.1V
R472 16V L452 J401
C448 2.2k 1.1V 0µH 0P
2
7
C444 IN2 OUT2
0.1 47p 10V R470
C434 3.3V
3
6
R461 R462 100k REF VCC
C442 1.4V 33k 2.2k 50V C462 4.7 4.7 L453
470p 1.3V 0µH
4
10
1.4V C461 16V IC408
10 R495 R497 LA4534M C453
16V 3.3k 47k 0.01
B
C449 C435 RV400 C463 C474 C455 C456
0.1 10 R450 5k 47 0.1 C452 R473 R474 0.1 0.1
B 10V 47k 16V B 22 100k 100k 16V 16V
16V PET PET
C454
VOLUME 220
MONITOR AMP 16V
4
MB-3(2/2)
CP301
202