Professional Documents
Culture Documents
Boom Angle WA380
Boom Angle WA380
Boom Angle WA380
1. Hold down the "SW < SW for 5 seconds or 4. Press the < and > SW to display the [Work
more at the same time, and change to the [ID Equipment Lift Arm Angle Adjustment] screen
Entry] screen. of set item 2.
2. After the ID is entered using the < and > SW, 5. Press the $SW here; the [Work Equipment Lift
press the $SW to enter the service person Arm Angle Set] screen appears.
screen.
WA380-5 10-245
STRUCTURE AND FUNCTION,
MAINTENANCE STANDARD MACHINE MONITOR
Item setting
1. Hold down the < and > SW for 5 seconds or more at he same time, and change to the [ID Entry] screen.
2. Use the < and > SW to enter ID, and press the "SW to enter the service person screen.
3. Use the < and > SW to display the [Sensor Initial Setting Selection] screen, and press the $SW to
decide the value.
4. Use the < and > SW to display the [Work Equipment EPC Adjustment] screen on set items 4 to 7.
Lift arm up: No.4
Lift arm down: No.5
Bucket tilt: No.6
Bucket dump: No.7
3-valve extension: No.8
3-valve reduction: No.9
Set the value individually.
5. Press the $SW here; the [Work Equipment EPC Setting] screen appears.
10-246 WA380-5
STRUCTURE AND FUNCTION,
MAINTENANCE STANDARD MACHINE MONITOR
WA380-5 10-247
STRUCTURE AND FUNCTION,
MAINTENANCE STANDARD MACHINE MONITOR
Bucket tilt
1. Dump the bucket to lower the lift arm, and lift the front tires. Tilt the bucket by degrees in the engine
high idling state. (Lower the machine.)
2. Return the lever by fine operation to stop the bucket (tire floating), then hold the lever at that position.
3. Press the $SW here; the EPC command value is read, and a difference between the read value and ref-
erence value is stored as an offset value.
4. The buzzer sounds twice (two short tones), and the menu returns to the [Work Equipment EPC Adjust-
ment] screen. The setting is then completed.
5. When the $SW is pressed as the lever stroke is in the dump direction, the buzzer sounds for 1 second,
and the adjustment is canceled as the [Work Equipment EPC Setting] screen remains displayed.
6. When the $SW is pressed as the lever is at the neutral position, the adjustment value is cleared, and
the buzzer sounds twice (two short tones). The menu then returns to the [Work Equipment EPC Adjust-
ment] screen.
7. When the "SW is pressed, the work equipment EPC dispersion correction is ended even if it is in
progress of processing.
Bucket dump
1. Adjust the bucket to the horizontal level without load, and lower the bucket by degrees in the engine
high idling state.
2. Return the lever by fine operation to stop the lift arm, then hold the lever at that position.
3. Press the $SW here; the EPC command value is read, and a difference between the read value and ref-
erence value is stored as an offset value.
4. The buzzer sounds twice (two short tones), and the menu returns to the [Work Equipment EPC Adjust-
ment] screen. The setting is then completed.
5. When the $SW is pressed as the lever stroke is in the tilt direction, the buzzer sounds for 1 second, and
the adjustment is canceled as the [Work Equipment EPC Setting] screen remains displayed.
6. When the "SW is pressed as the lever is at the neutral position, the adjustment value is cleared, and
the buzzer sounds twice (two short tones). The menu then returns to the [Work Equipment EPC Adjust-
ment] screen.
3-valve extension
1. Extend three valves by degrees in the engine high idling state.
2. Return the lever by fine operation. After the cylinder of three valves stops, hold the lever at that posi-
tion.
3. Press the $SW here; the EPC command value is read, and a difference between the read value and ref-
erence value is stored as an offset value.
4. The buzzer sounds twice, (two short tones), and the menu returns to the [Work Equipment EPC Adjust-
ment] screen. The setting is then completed.
5. When the $SW is pressed as the lever stroke is in the fastening direction, the buzzer sounds for 1 sec-
ond, and the adjustment is canceled as the [Work Equipment EPC Setting] screen remains displayed.
6. When the $SW is pressed as the lever is at the neutral position, the adjustment value is cleared, and
the buzzer sounds twice (two short tones). The menu then returns to the [Work Equipment EPC Adjust-
ment] screen.
7. When the "SW is pressed, the work equipment EPC dispersion correction is ended even if it is in
progress of processing.
3-valve reduction
1. Reduce three valves by degrees in the engine high idling state.
2. Return the lever by fine operation. After the cylinder of three valves stops, hold the lever at that posi-
tion.
3. Press the $SW here; the EPC command value is read, and a difference between the read value and ref-
erence value is stored as an offset value.
4. The buzzer sounds twice, (two short tones), and the menu returns to the [Work Equipment EPC Adjust-
ment] screen. The setting is then completed.
5. When the $SW is pressed as the lever stroke is in the extension direction, the buzzer sounds for 1 sec-
ond, and the adjustment is canceled as the [Work Equipment EPC Setting] screen remains displayed.
6. When the $SW is pressed as the lever is at the neutral position, the adjustment value is cleared, and
the buzzer sounds twice (two short tones). The menu then returns to the [Work Equipment EPC Adjust-
ment] screen.
7. When the "SW is pressed, the work equipment EPC dispersion correction is ended even if it is in
progress of processing.
10-248 WA380-5
STRUCTURE AND FUNCTION,
MAINTENANCE STANDARD MACHINE MONITOR
1. Push and hold the "SW and > switch simulta- 4. Display the screen for adjusting items No. 4 — 6
neously for 5 seconds to go to the "Input ID" of the work equipment EPC with the < switch
screen. and > switch.
WA380-5 10-249
STRUCTURE AND FUNCTION,
MAINTENANCE STANDARD MACHINE MONITOR
< Adjustment of each EPC lever > [Adjustment of position of lift arm RAISE
[Adjustment of position of lift arm LOWER detent]
(FLOAT) detent] Perform the following procedure with the
1) -1. Lower the lift arm to the ground. engine stopped.
2) -1. Stop and hold the lift arm lever before the 1) -2. Lower the lift arm to the ground.
FLOAT detent position. 2) -2. Stop and hold the lift arm lever before the
3) -1. Push the $SW at this time. The lever voltage RAISE detent position.
is read and the standard value is changed and 3) -2. Push the $SW at this time. The lever voltage
saved. is read and the standard value is changed and
4) -1. The buzzer sounds twice. The screen for saved.
adjusting the work equipment EPC appears and 4) -2. The buzzer sounds twice. The screen for
the adjustment is completed. adjusting the work equipment EPC appears and
the adjustment is completed.
Screen for adjusting work equipment EPC 5) -2. At this time, if the $SW is pushed while the
lever output voltage is below the standard value
(out of design range), the buzzer sounds for 1 sec-
ond and the screen for setting work equipment
EPC does not change. The adjustment is can-
celled in this case.
10-250 WA380-5
STRUCTURE AND FUNCTION,
MAINTENANCE STANDARD MACHINE MONITOR
WA380-5 10-251
STRUCTURE AND FUNCTION,
MAINTENANCE STANDARD MACHINE MONITOR
2. Use the < and > SW to enter ID, and press the
$SW to enter the service person screen.
10-252 WA380-5
STRUCTURE AND FUNCTION,
MAINTENANCE STANDARD MACHINE MONITOR
2. Use the < and > SW to enter ID, and press the 5. Press the $SW here; the [Work Equipment Lift
$SW to enter the service person screen. Arm Angle Setting] screen appears.
3. Use the < and > SW to display the [Sensor Ini- 6. Adjust the lift arm to the highest position with-
tialization Setting] screen, and press the $SW out load.
to decide the value. 7. Press the $SW here; the lift arm angle sensor
value is read, and a difference between the read
result and reference value is stored as an offset
value.
8. The buzzer sounds twice (two short tones), and
the menu returns to the [Lift Arm Angle Adjust-
ment] screen. The setting is then completed.
9. Press the "SW; the lift arm angle correction is
ended even if it is in progress of processing.
WA380-5 10-253
STRUCTURE AND FUNCTION,
MAINTENANCE STANDARD MACHINE MONITOR
1. Hold down the "SW < SW for 5 seconds or 4. Use the < and > SW to display the [Work Equip-
more at the same time, and change to the [ID ment Lift Arm Angle Adjustment] screen of set
Entry] screen. item 17.
2. Use the < and > SW to enter ID, and press the 5. Press the $SW here; the [Work Equipment Lift
$SW to enter the service person screen. Arm Angle Setting] screen appears.
3. Use the < and > SW to display the [Sensor Ini- 6. Adjust the lift arm to the lowest position with-
tialization Setting] screen, and press the $SW out load. (Lift arm cylinder stroke end)
to decide the value. 7. Press the $SW here; the lift arm angle sensor
value is read, and a difference between the read
result and reference value is stored as an offset
value.
8. The buzzer sounds twice (two short tones), and
the menu returns to the [Lift Arm Angle Adjust-
ment] screen. The setting is then completed.
9. Press the "SW; the lift arm angle correction is
ended even if it is in progress of processing.
10-254 WA380-5