Professional Documents
Culture Documents
J125-3223 Parts Book
J125-3223 Parts Book
J125-3223 Parts Book
Schramm, Inc.
800 East Virginia Ave.
West Chester, PA. 19380 USA
1. This limited warranty applies only to the original user/customer and only to machines and equipment which
have been subjected to normal use and service.
2. This limited warranty is for a period of 12 months from initial operation or 2000 hours, whichever occurs first;
not to exceed 18 months from the date of shipment.
3. Schramm’s obligation under this limited warranty shall be solely to replace or repair without charge at the
dealer’s location those component parts which Schramm itself manufactured, and only if such component parts
were defective when the machine or equipment was shipped from Schramm’s factory. Any component part
installed to replace a defective component part is warranted solely for the duration of the unexpired warranty on
the machine or equipment in which such a component part is installed.
4. This machine or equipment may incorporate many component parts manufactured by companies other than
Schramm, such as truck chassis, carriers, tracks, engines, tires, hydraulic pumps, hydraulic motors and other
component parts too numerous to list. This limited warranty does not apply to such component parts, but such
component parts may be warranted by the companies that manufactured them.
5. This limited warranty does not apply to regular maintenance replacement items, including but not limited to
V-belts, electrical bulbs, wiper blades, filters, lubricants, and batteries. This limited warranty does not apply to
normal maintenance service and adjustments, including, but not limited to fuel, air and hydraulic system
cleaning, engine tune-up, clutch inspection and adjustment.
6. It shall be the obligation of the user/customer to pay for transportation of this machine or equipment to the
dealer providing warranty service and to pay for travel time or mileage if warranty service is provided at the job
site.
7. Unless notified in writing by Schramm, Inc. all replacement parts must be returned to Schramm, Inc.,
transportation charges prepaid.
8. In order for this limited warranty to apply, this machine or equipment must be made available for repair during
the warranty period.
9. Schramm, Inc. shall not be liable for defects, damages or failures caused by unauthorized alterations, use of
non-approved parts, unreasonable use, neglect, abuse, accident, or negligent repair, including a failure to
provide reasonable and necessary maintenance after the new machine is in service.
10. Schramm, Inc. reserves the right to make design changes or any product improvements at any time, without
incurring any obligation to install same on units previously manufactured.
11. There are no warranties, expressed or implied, other than the limited warranty, as set forth above and this
limited warranty supersedes any warranty, promises or representations previously made or issued. THERE
ARE ABSOLUTELY NO IMPLIED WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A
PARTICULAR PURPOSE and Schramm hereby excludes all such warranties which might otherwise be implied
by law.
12. Schramm’s liability for breach of this limited warranty, whether a claim or lawsuit is brought in contract, tort or
strict liability, shall be limited exclusively to repair or replacement of defective parts manufactured by Schramm.
Schramm shall not be liable for any direct or indirect incidental or consequential damages of any kind which
may result from defects in its products or from breach of this limited warranty nor shall Schramm be liable for
any damages resulting from a user/customer’s loss of any use of this Schramm machine or equipment.
Chapter 2
Chapter 1
T685WS-D
Table of Contents
IMPORTANT NOTE ABOUT THIS PARTS BOOK - PLEASE READ
This Parts Book details all parts, options and assemblies available for the Schramm
T685WS-D series of rigs. Because your T685WS-D rig has been custom built to your
specific needs, all of the parts, options and assemblies detailed in this book may not
be included on your rig. Therefore when necessary, please refer to the Detailed Rig
Specifications (page A1) in the Appendix for a listing of the actual options and
assemblies used to build your rig.
Chapter 1 Rig
Chapter 2 Mast
Schematic Diagrams
Page intentionally blank
T685WS-D
Chapter
This Parts Book details all parts, options and assemblies available for the Schramm
T685WS-D series of rigs. Because your Rotadrill T685WS-D rig has been custom built
to your specific needs, all of the parts, options and assemblies detailed in this book may
not be included on your rig. Therefore when necessary, please refer to the Detailed Rig
Specifications (page A1) in the Appendix for a listing of the actual options and
assemblies used to build your rig.
T685WS-D
Rig: Table of Contents
Heat
Exchanger
Air
Cleaners
Engine
Front
Outriggers
Air/Oil Tank
Fuel
Tank
Hydraulic
Tank
Toolbox
Page Page
Air Cleaner............................................................ 1-39 Gearboxes & Pumps ............................................ 1-40
Air-Oil Tank........................................................... 1-26 Heat Exchanger ................................................... 1-28
Battery Box .......................................................... 1-51 Fan & Mounting ............................................ 1-31
Compressor .......................................................... 1-54 Heater, Diesel Fired Coolant ................................ 1-52
Clutch Assembly ........................................... 1-56 Hydraulic Tank ..................................................... 1-32
Control Panel ....................................................... 1-4 Muffler .................................................................. 1-38
Engine Control Panel ................................... 1-9 Outriggers
Lighting ........................................................ 1-10 Dual Front Outboard .................................... 1-16
Reference Information ................................. 1-12 Rear Outriggers ........................................... 1-18
Cyclone ................................................................ 1-68 Front Outriggers Kit ...................................... 1-20
Engine ................................................................. 1-34 Splitters
Foam Injection ..................................................... 1-64 Rotary Free Standing ................................... 1-69
Fuel Filters ............................................................ 1-24 Stand Pipe ........................................................... 1-67
Fuel Tanks .......................................................... 1-22 Tool Lubricator, Piston Pump ............................... 1-48
T685WS-D
Rig: Table of Contents
Muffler
Control
Panel
Compressor
Tool
Lubricator
Page
Toolbox ................................................................ 1-49
Variable Speed Cooling Fan ............................... 1-59
Water Injection
25gpm .......................................................... 1-60
35gpm .......................................................... 1-61
CAT Hi Pressure .......................................... 1-62
Winches
Survey Winch .............................................. 1-70
Main Control Panel
24 7
8
23
22 9
21
10
20 11
12
19 13
14
A D
15
B 18
C E
16
17
1-4 T685WS-D
Main Control Panel
WATER INJECTION
A 2259-0060 1 INLET VALVE SECTION 5001-A-1
2916-0111 1 LEVER KIT 5000 45 DEG
2259-0064 1 VALVE SECT 5002-A-11
AUX ROTATION
2916-0110 1 LEVER KIT 5000 VERTICAL
2259-0078 1 VALVE SECT 5002-DA21 DETENTED
2259-0065 1 OUTLET VALVE SECTION 5003-A-4
AIR VALVE
B 2259-0060 1 INLET VALVE SECTION 5001-A-1
2916-0111 1 LEVER KIT 5000 45 DEG
2259-0116 1 VALVE SECT 5002-A522 W/P.R.
BLOWBACK VALVE
2916-0110 1 LEVER KIT 5000 VERTICAL
2259-0116 1 VALVE SECT 5002-A522 W/P.R.
FORK WRENCH
2916-0111 1 LEVER KIT 5000 45 DEG
2259-0116 1 VALVE SECT 5002-A522 W/P.R.
PIPE TROUGH
2916-0110 1 LEVER KIT 5000 VERTICAL
2259-0116 1 VALVE SECT 5002-A522 W/P.R.
SURVEY BOOM
2916-0111 1 LEVER KIT 5000 45 DEG
2259-0086 1 VALVE SECT 5002-A269 W/PR CAV
2259-0065 1 OUTLET VALVE SECTION 5003-A-4
T685WS-D 1-5
Control Panel
MAST TILT
2916-0111 1 LEVER KIT 5000 45 DEG
2259-0086 1 VALVE SECT 5002-A269 W/PR CAV
MAST SLIDE
2916-0110 1 LEVER KIT 5000 VERTICAL
2259-0082 1 VALVE SECT 5002-A465 W/PR CAV
D SLOW FEED
2259-0128 1 VALVE SECTION DUCTILE INLET
2916-0111 1 LEVER KIT 5000 45 DEG
2259-0078 1 VALVE SECT 5002-DA21 DETENTED
BREAKOUT WRENCH
2916-0110 1 LEVER KIT 5000 VERTICAL
2259-0077 1 VALVE SECT 5002-DA5 W/PR CAV
2259-0065 1 OUTLET VALVE SECTION 5003-A-4
1-6 T685WS-D
Control Panel
SURVEY WINCH
2258-0335 1 VALVE HYD HRC 45-375 PSI S.CTR
0933-0003 1 KNOB HAND 1-3/8 DIA X 1/2 NF
2916-0114 1 HANDLE HRC VALVE 1/2NF X 3-5/8
Available service kit 3030-0217 includes:
2 PLUG
2 O-RING
5001-0071 1 BOOT, HANDLE
5001-0899 1 LEVER PIVOT PIN
5001-0900 1 LEVER RECEPTACLE
5001-0715 1 SPRING HRC 50/295 PSI RANGE
ROTATION
2258-0297 1 VALVE HYD HRC 45-375 PSI F.LCK
0933-0003 1 KNOB HAND 1-3/8 DIA X 1/2 NF
2916-0114 1 HANDLE HRC VALVE 1/2NF X 3-5/8
5001-0071 1 BOOT, HANDLE
5001-0653 1 SHOE FRICTION LOCK HRC
5000-9829 1 KIT, HRC FRICTION LOCK REPAIR
KIT INCLUDES:
2 BALL
1 BRACKET
1 SHOE (5001-0653)
1 NUT (HEX HANDLE)
4 WASHER
1 PLATE
1 PIVOT BOLT (5001-0978)
1 SPRING
2 RETAINING RING
1 PIVOT PIN
T685WS-D 1-7
Control Panel
1-8 T685WS-D
Engine Control Panel
1 2 4 5 6
12 11 9 10 9 8 7
T685WS-D 1-9
Control Panel Lighting
4 3
1-10 T685WS-D
Page intentionally blank
Control Panel - Reference Information
CONTROL ASSEMBLIES
The illustration below shows a general arrangement for all of the directional control valve sections on your rig.
Depending on the specific application, the number of sections may vary and behavior is optimized for its application.
Reference the specific bill of materials to identify the specific valve sections, lever kits, tie rod kits,
and hydraulic plumbing material.
Reference the rig specific hydraulic diagram provided with this parts book for a definition of valve functionality.
TIE ROD
INLET
Part # Description
5000-9588 1 SECTION 5000
5000-8666 2 SECTION 5000
OUTLET
5000-9110 3 SECTION 5000
5000-8667 4 SECTION 5000 VALVE SECTIONS
5000-9201 5 SECTION 5000
5000-8668 6 SECTION 5000
5000-9487 7 SECTION 5000
5000-9574 8 SECTION 5000
5000-9575 9 SECTION 5000
5000-9589 10 SECTION 5000
1-12 T685WS-D
Control Panel - Reference Information
5001-0449
SPRING CENTERING
5000-9831
DETENT
T685WS-D 1-13
Control Panel - Reference Information
5001-2607
5001-2606
HRC ASSEMBLY
SPACER HRC
SPACER HRC
VALVE HYD.
HRC
1-14 T685WS-D
Control Panel - Reference Information
The valve configuration drawings shown below are for reference only and
T685WS-D 1-15
Outriggers, Dual Front Outboard
P125-1510
4
1
5
3
7
8
11
12
13
10
15 14
16
1-16 T685WS-D
Outriggers, Dual Front Outboard
P125-1510
T685WS-D 1-17
Rear Outriggers
10
1-18 T685WS-D
Rear Outriggers
T685WS-D 1-19
Front Outriggers Kit
P125-1520
DISCLAIMER: This kit is made available by Schramm Inc., to enable customers to modify the location of the Dual Front
Outriggers to their own particular needs.
Schramm Inc. will not be held liable for any property damage, severe injury, or death resulting from the customization of
a Schramm rig by our customers.
Any equipment alteration without written consent of the manufacturer voids the warranty and can cause property
damage, severe injury, or death.
1-20 T685WS-D
Page intentionally blank
Fuel Tanks
0211-0113
1
6
RIGHT HAND 8
FUEL TANK
10
13 11
11
12
14
15
6 16
LEFT HAND
FUEL TANK
1
17
1-22 T685WS-D
Fuel Tanks
0211-0113
T685WS-D 1-23
Racor Fuel Filter
P124-1900
1-24 T685WS-D
Racor Fuel Filter
P124-1900
5
6
T685WS-D 1-25
Air, Oil Tank
0278-0111
4 5
1-26 T685WS-D
Air, Oil Tank
0278-0111
T685WS-D 1-27
Heat Exchanger
0670-0120
1-28 T685WS-D
Heat Exchanger
0670-0120
T685WS-D 1-29
Page intentionally blank
Heat Exchanger Fan & Mounting
4 11
2 3
9
10
1
6
T685WS-D 1-31
Hydraulic Tank
2912-0073
4
1
19
17
18
9
10 11
12
13
14
15
16
1-32 T685WS-D
Hydraulic Tank
2912-0073
A B
T685WS-D 1-33
Engine T685WS-D
2600-0129
1-34 T685WS-D
Engine T685WS-D
2600-0129
4 5 6
T685WS-D 1-35
Engine T685WS-D
2600-0129
1-36 T685WS-D
Page intentionally blank
Engine Muffler
1
7
4
2
6
1-38 T685WS-D
Air Cleaner
6
7
T685WS-D 1-39
Gearboxes & Pump Sub Assemblies
1040-0079
7
9
6 8
5
7
1
3
Ref Part # Qty Description
1 SEE PAGE 1-33 1 PUMP, P1
2 SEE PAGE 1-34 1 PUMP, P2
3 SEE PAGE 1-36 1 PUMP, P3
4 SEE PAGE 1-38 1 PUMP, P4
5 SEE PAGE 1-39 1 PUMP, P5
6 1040-0050 2 GEARBOX TRIPLE FUNK .91:1
Available service items include:
5001-1890 SHAFT ASSEMBLY
7 0877-1339 2 SUPPORT GEARBOX
8 1107-0023 1 FLANGE MTG GEARBOX
9 9S02-0037 4 SCREW CAP NF 1/2X1-1/4
1-40 T685WS-D
Gearboxes & Pump Sub Assemblies
1040-0079
7
9
10
14
3
13
11
12
T685WS-D 1-41
Gearboxes & Pump Sub Assemblies
1040-0079
12
11
10
2
16
13
15
14
4
3
6
5
1-42 T685WS-D
Page intentionally blank
Gearboxes & Pump Sub Assemblies
1040-0079
10
11
9
12
22
23
3
2
6
5
4
1
13
21
20 15
19 19
18
17
16
14
1-44 T685WS-D
Gearboxes & Pump Sub Assemblies
1040-0079
T685WS-D 1-45
Gearboxes & Pump Sub Assemblies
1040-0079
7
6
4
5
14
8
9
10
2
11
13
3
12
1-46 T685WS-D
Gearboxes & Pump Sub Assemblies
1040-0079
T685WS-D 1-47
Tool Lubricator, Piston Pump
P125-2301
1-48 T685WS-D
Toolbox
P125-6317
T685WS-D 1-49
Page intentionally blank
Battery Box
0159-0059
T685WS-D 1-51
Heater, Diesel Fired Coolant
P125-1920
1-52 T685WS-D
Heater, Diesel Fired Coolant
P125-1920
3 2 1
1 2 3
T685WS-D 1-53
Compressor, Sullair 1350/500
P125-2009
2
3
13
12
6 11
7
8
10
1-54 T685WS-D
Compressor, Sullair 1350/500
P125-2009
T685WS-D 1-55
Clutch Assembly
8 11 5 1 7 2
8A
8C
8B
16 17
12 19
18 10
13 14 15
1-56 T685WS-D
Clutch Assembly
T685WS-D 1-57
Page intentionally blank
Variable Speed Cooling Fan with Compressor
P125-1905
3
Engine
2
Radiator
Pipe
Back of
Hydraulic Tank
T685WS-D 1-59
Water Injection, Bean 25gpm
P125-3918
1 7
1-60 T685WS-D
Water Injection, Bean 35gpm
P125-3920
T685WS-D 1-61
Water Injection, CAT High Pressure
P125-3921
1-62 T685WS-D
Water Injection, CAT High Pressure
P125-3921
T685WS-D 1-63
Foam Injection
P125-3970
1-64 T685WS-D
Foam Injection
P125-3970
T685WS-D 1-65
Stand Pipe, 2” Auxiliary Mud
P125-2632
1-66 T685WS-D
Stand Pipe, 2” Auxiliary Mud
P125-2632
T685WS-D 1-67
Cyclone, LH Mounted
P125-5411
3
2
1-68 T685WS-D
Splitter, Rotary Free Standing
P125-5424
T685WS-D 1-69
Survey Winch, 6000lb
P125-3505
1-70 T685WS-D
Survey Winch, 6000lb
P125-3505
T685WS-D 1-71
Page intentionally blank
T685WS
Chapter
This Parts Book details all parts, options and assemblies available for the Schramm
T685WS series of rigs. Because your T685WS rig has been custom built to your
specific needs, all of the parts, options and assemblies detailed in this book may not be
included on your rig. Therefore when necessary, please refer to the Detailed Rig
Specifications (page A1) in the Appendix for a listing of the actual options and
assemblies used to build your rig.
Page intentionally blank
T685WS
Mast: Table of Contents
Page
Jib Boom Altitude Compensator .......................................... 2-45
Big Tool Breakout ................................................ 2-32
Bit Breakers ......................................................... 2-61
Blowdown Valve .................................................. 2-67
D.O.T. Clearance Lights ...................................... 2-57
Emergency Stop Button ...................................... 2-56
Floating Sub ........................................................ 2-62
Jib Boom
Hydraulic (Exploration) ................................ 2-34
Tophead Swing and Extend ........................................ 2-36
Lazy Susan .......................................................... 2-28
Masts
30’ Sliding Angle Mast ................................. 2-4
93700lb Offset ............................................. 2-10
Tilt Cylinders ................................................. 2-14
Pivot Bearing ............................................... 2-15
Mini Lube System ................................................ 2-31
Petol Drill Pipe Tong ............................................ 2-66
Setup
4.5” x 20’ RC, No Sub .................................. 2-58
4.5” x 2 7/8” IF x 30’ ..................................... 2-59
4.5” x 3.5” REG x 25’ ................................... 2-60
Single Pipe Loading Arm ..................................... 2-24
Tables
Split Table, 4 1/2”, 22” Max, SAM ................ 2-37
Split Table, 4 1/2”, 28” Max ......................... 2-38
Tophead
Casing Lifting Eyes ...................................... 2-51
High Capacity .............................................. 2-46
High Capacity 2 Motor Offset ...................... 2-50
High Capacity 2 Motor 5” SAM .................... 2-50
Motors .......................................................... 2-54
Side Inlet Swivel .......................................... 2-55
Swivel and Floating Shaft ............................ 2-64
Wrench, Breakout ................................................ 2-22
Winches
9600lb (150’ x 1/2”) ...................................... 2-16
15000lb (150’ x 5/8”) .................................... 2-19
Sandline (2100’ x 5/16”) .............................. 2-20
Survey, Swing Arm SAM ............................. 2-42
Breakout
Arm
Table
Mast 30’ SAM
3 4 5
14
12 2
7
1
15
8
17
6
9
10
21
11 13
2
18 19 20
16
2-4 T685WS
Mast 30’ SAM
MAST 74,000 LB
2813-0274 2 CYL HYD 5.5 X 2.75 X 180
Available service items include:
3030-0295 SEAL KIT
T685WS 2-5
Mast 30’ SAM
2-6 T685WS
Mast 30’ SAM
T685WS 2-7
Mast 30’ SAM
2-8 T685WS
Page intentionally blank
Mast 93,700lb Offset
P124-2802/2806
7
6 8
5
1
10
11
17
12
14
13
15
16
2-10 T685WS
Mast 93,700lb Offset
P124-2806
38' MAST
2813-0311 2 CYL HYD 6 X 2.75 X 228
Available service items include:
3030-0318 SEAL KIT
T685WS 2-11
Mast 93,700lb Offset
P124-2802/2806
2-12 T685WS
Mast 93,700lb Offset
P124-2802/2806
T685WS 2-13
Mast Tilt Cylinders
2-14 T685WS
Mast Pivot Bearing
T685WS 2-15
Winch, 9600lb (150’ x 1/2”)
P124-3503
13
UNDERSIDE OF MAST 1
2 3 4
9 10 11
5
18
2-16 T685WS
Winch, 9600lb (150’ x 1/2”)
P124-3503
13
14
15
17
16
Ref. Part # Qty Description
1 1120-0051 1 WINCH ASY BRADN PD12C 10K PULL
Available service items include:
5001-0525 MOTOR
5000-9928 MOTOR SEAL KIT
5001-2276 ROPE WEDGE
5001-2250 BRAKE CLUTCH ASY
5000-9968 WINCH SEAL KIT
2 9S01-0100 8 SCREW CAP NC 5/8X2
3 9W03-0010 8 WASHER LOCK 5/8
4 0570-0155 8 WASHER HT SAE 5/8"
5 3883-0010 1 ELBOW 90 16MOA-12M37 XHP
6 3332-0019 1 CONN 16MO-12M37
7 3896-0002 1 TEE 06F37-06M37-06M37
8 3897-0005 1 REDUCER TUBE 06-04
9 3896-0001 1 TEE 04F37-04M37-04M37
10 3854-0005 1 CONN 04FP-04F37
11 3332-0039 1 CONN 04MP-04M37 RESTR .055
13 3317-0076 1 CABLE WINCH 1/2 X 150 HSLR
14 3346-0010 1 PLUG HEX 04MO
15 3332-0028 1 CONN 04MP-06M37
16 2789-0021 1 HOOK WINCH 12000# CAPACITY
17 3530-0011 1 SHACKLE ANCHOR 7/8
T685WS 2-17
Winch, 15000lb (150’ x 5/8”)
P124-3507
2 3
4 5 6
2-18 T685WS
Winch, 15000lb (150’ x 5/8”)
P124-3507
T685WS 2-19
Winch, Sandline (2100’ x 5/16”)
P124-3506
1 2
4
7 6
2-20 T685WS
Winch, Sandline (2100’ x 5/16”)
P124-3506
T685WS 2-21
Breakout Wrench 60”
P124-2905
5
2
2-22 T685WS
Breakout Wrench 60”
P124-2905
T685WS 2-23
Single Pipe Loading Arm
P124-3310
2 3
11
7
12
1
7
10
9
8 13
14
15
16
2-24 T685WS
Single Pipe Loading Arm
P124-3310
T685WS 2-25
Single Pipe Loading Arm
P124-3310
2-26 T685WS
Page intentionally blank
Lazy Susan, 12 Rod
P124-3311
5 6
3 7
10
2-28 T685WS
Lazy Susan, 12 Rod
P124-3311
T685WS 2-29
Lazy Susan, 12 Rod
P124-3311
2-30 T685WS
Mini Lube System
P124-2902
1 2
T685WS 2-31
Big Tool Breakout
P124-2921
10
5 6
7
2-32 T685WS
Big Tool Breakout
P124-2921
T685WS 2-33
Jib Boom, Hydraulic (Exploration)
P124-3346
6
2
1
11
10
12
5
2-34 T685WS
Jib Boom, Hydraulic (Exploration)
P124-3346
T685WS 2-35
Jib Boom, Hydraulic Swing & Extend
P124-3340
2-36 T685WS
Split Table, 4-1/2”, 22” max, SAM
P124-3600
3
2
5
7
T685WS 2-37
Split Table, 4 1/2”, 28” max
P124-3643
5 15
10
11
13
12
12
14
2-38 T685WS
Split Table, 4 1/2”, 28” max
P124-3643
T685WS 2-39
Page intentionally blank
Matrix Pipe Size Mod to Slips
P125-3313
T685WS 2-41
Survey Winch Swing Arm SAM
P124-3303 /P125-3506
2
3
2-42 T685WS
Survey Winch Swing Arm SAM
P124-3303/P125-3506
T685WS 2-43
Page intentionally blank
Altitude Compensator
P124-1904
2
1
T685WS 2-45
Tophead, High Capacity
0870-0119
2-46 T685WS
Tophead, High Capacity
0870-0119
35
36
32
31
34
20
29
28
16
48 49
30
22
26
46
47 19
14
53
11
17 18
15
9
45
55
18 39
41 38
6
T685WS 2-47
Tophead, High Capacity
0870-0119
NOTE: All items listed below are available as a Service Box (0870-0187).
2-48 T685WS
Tophead, High Capacity
0870-0119
T685WS 2-49
Tophead High Capacity 2 Motor Offset
P124-3004
1
8
5
7
5A
3
4
2-50 T685WS
Casing Lifting Eyes
P124-2910
T685WS 2-51
Tophead High Capacity 2 Motor 5”, SAM
P124-3008
3
6
4
2-52 T685WS
Tophead High Capacity 2 Motor 5”, SAM
P124-3008
T685WS 2-53
Motors Tophead
2
Ref Part # Qty Description
1 MOTORS
2999-0097 1 MOTOR HYD CHARLYNN 20.6 CU. IN.
2999-0096 1 MOTOR HYD CHARLYNN 29.2 CU. IN.
3 2999-1000 1 MOTOR HYD CHARLYNN 40.6 CU. IN.
Available service items include:
5000-5236 SEAL KIT
5000-5237 SHAFT SEAL KIT
5001-0381 SEAL KIT MOTOR (FOR 20.6 CU. IN. ONLY)
5
KEY 9/16 SQ X 2" LONG KEY (SUPPLIED WITH
2 1
MOTORS)
4
3 0038-0005 1 PINION INPUT 20T 4PD 5P
4 9C01-0033 1 PIN COTTER PLT 1/8 X 3
5 5001-0735 1 SHAFT NUT
2-54 T685WS
Side Inlet Swivel, High Capacity
P124-5416
T685WS 2-55
Emergency Stop Button
P124-2919
2
2
2-56 T685WS
D.O.T. Clearance Lights - Mast
P125-2909
T685WS 2-57
Setup 4.5” x 20’ RC, NO SUB
P124-7000/7003
2-58 T685WS
Setup 4.5” x 2 7/8” IF x 30’
P124-7001
T685WS 2-59
Setup 4.5” x 3.5” REG x 25’
P124-7020
2-60 T685WS
Bit Breakers
P124-6826/6827
T685WS 2-61
Floating Sub
P124-3380/3381
8 9
2-62 T685WS
Floating Sub
P124-3380/3381
T685WS 2-63
Swivel & Floating Shaft for 5” Tophead
P124-5418
2-64 T685WS
Swivel & Floating Shaft for 5” Tophead
P124-5418
T685WS 2-65
Petol Drill Pipe Tong
P124-3653
2-66 T685WS
Blowdown Valve
P124-5417
1 2
T685WS 2-67
Page intentionally blank
T685WS-D
APPENDIX:
Table of Contents
Schematic Diagrams
Page intentionally blank
Detailed Rig Specifications
High capacity single reduction top head drive rotation and efficient pipe
handling systems make the T685WS ideal for the toughest drilling
projects in the water well, shallow oil and gas, environmental, mineral
exploration and surface mining fields, using down-the-hole hammer, air rotary,
mud rotary and dual tube techniques.
Weight & Dimensions - Weight and size estimates for specifically configured
machines are available upon request.
Unit Engine - Electronically fuel injected, 90 degree vee, twelve cylinder, twin
turbocharged, after-cooled, 4-cycle, water cooled diesel engine provides power
to the hydraulic pumps from the front crankshaft flange and the air compressor
from the flywheel end. Includes dual 110 gal (416 l) fuel tanks. Tier 1
Emissions compliant
Model: Detroit Diesel DDC/MTU 12V-2000TA DDEC
Power: 760 bhp (567 kw) @ 1,800 rpm
Torque: 2,188 ft-lb (2,967 N-m) @ 1,800 rpm
Displacement: 1,458 cu. in. (23.9 l)
B.S.F.C.: .338 lb/bhp-hr @ Maximum Power (206 g/kw-hr)
Fuel Consumption: 36.2 g/hr @ Maximum Power, 27 g/hr @ Average Load
Ratings @ 1,950 rpm:
Power: 760 bhp (567 kw)
Torque: 2,020 ft-lb (2,739 N-m)
B.S.F.C.: .349 lb/bhp-hr @ Maximum Power (212 g/kw-hr)
Fuel Consumption: 37.4 g/hr @ Maximum Power, 28 g/hr @ Average Load
Ratings @ 2,100 rpm:
Power: 750 bhp (560 kw)
Torque: 1,875 ft-lb (2,542 N-m)
B.S.F.C.: .362 lb/bhp-hr @ Maximum Power (220 g/kw-hr)
Fuel Consumption: 38.8 g/hr @ Maximum Power, 29 g/hr @ Average Load
Horsepower Ratings: +2%, -0%
Air/Mud Fluid Lines - Rated at 1,500 psi (104 bar) from the air/oil receiver
outlet line through the rotation head, 2" ID (50.8 mm). Allows a booster
T685WS A-1
Detailed Rig Specifications
compressor (max. pressure 1,500 psi) to be teed into this air line.
Hydraulic System - Six hydraulic pumps, two fixed displacement type and
four variable volume piston type, provide hydraulic power for all rig functions.
System design is 100% open loop with directional control valves and full return
line filtration. In-tank return filters share common replaceable elements.
Suction lines are fitted with magnetic strainers. The system temperature is
thermostatically controlled utilizing an oil cooler. The rotation and rapid feed
piston pump and valves are of the load sensing type, matching pump flow to
demand. All hydraulic circuits are protected by relief valves. A hand pump is
provided to fill the tank through the filters. Shutoff valves are provided at each
tank suction outlet for ease of service.
Hydraulic Tank Capacity: 100 gal (378.5 l)
Hydraulic System Capacity: 160 gal (606 l)
Oil Filters: (4) in-tank 7 micron with condition indicator.
Hydraulic Tank Pressure: 5 psi relief valve regulated
Pressure Source: Bendix Tu-Flo 550 engine driven air compressor
Main Piston Pumps: Vickers
Auxiliary Gear Pumps: Commercial Intertech
Hydraulic Pump Drive - A three pad, constant mesh, spur gear, hydraulic
pump drive is connected to the front of the engine crankshaft with a coupling.
Model: Funk Mfg. 28000
Gear Ratio: .91:1
Coupling Model: Lovejoy Centaflex
Rear Outriggers and Mast Tilt - The outrigger system uses heavy square
section structural tubes which completely house the hydraulic cylinders.
Rear outriggers are an integral members of the drill rig frame. Dual lock check
valves and velocity fuses hold the outriggers in both load holding and
transport positions. All outriggers are independently positioned.
The two mast tilt cylinders are cushioned to reduce the shock loads imposed
on the mast pivot support when raising and lowering the mast. The control
valve in its fully shifted position will raise the mast quickly through approx.
85°, and slowly through the last 5°.
Rear Outrigger: (2) 5" Bore x 3-1/4" Rod x 41" Stroke (127 mm x 82.5 mm x
1,041 mm)
Mast Tilt: (2) 5" Bore x 2-1/2" Rod x 37" Stroke (127 mm x 63.5 mm x 940
mm)
A-2 T685WS
Detailed Rig Specifications
Tool Box - A lockable tool box is located on the left hand side of the rig
beneath the hydraulic tank. Capacity - 9 cu ft (.25 cu m)
Electrical System - The diesel driven alternator and batteries provide 24V DC
power. All exposed wiring is in "sealtite" conduit where applicable. All
circuits are protected by breakers. A remote mounted deck engine battery
disconnect switch is included.
Alternator: 24V DC - 75 amp
Batteries: (2) 12V connected in series
Mast Lights: (3) 60 Watt Floodlight
Control Panel: (2) Floodlights
Work Area: (1) 70 Watt Halogen Floodlight, (2) 70 Watt Halogen Spotlight
Accessories - Includes two sets operator's and parts manuals and 50 hour
maintenance kit.
When using the reverse circulation method, the cuttings are conveyed to the
surface through the top head and collected. A special air swivel packing
gland and top head shaft wear sleeve and adapter sub are provided with this
package. Inlet air swivel, floating sub and saver sub are not provided.
All welded rectangular ASTM A500 Grade B Steel tube construction. Member
selection and orientation to obtain maximum torsional, buckling and bending
resistance.
Drill pipe is usually handled pin down. A hydraulic holding fork is used to
T685WS A-3
Detailed Rig Specifications
support the drill string during rod changing operations. An adjustable pipe
wrench is operated by a hydraulic cylinder for quick break-out and pipe make-
up. Break-out cylinder offers a standard clevis attachment for mounting
optional wrenches and tongs.
Operating Angle: 0 - 45° manually locks in 5° increments
Mast Slide Travel: 8’ (2.44 m)
Overall Length: 36’8" (11.1 m)
Overall Width: 42-1/4" (1,073 mm)
Overall Depth: 27-1/2" (699 mm)
Head Travel: 30’ (9.1 m)
Std. Drill Pipe Length: 20' (6 m) or 25' (7.6 m)
Dynamic Load Rating: 100,000 lb (45,353 kg)
Angle Pipe Boom Capacity: 1,000 lb (454 kg)
The top head drive is driven by two hydraulic traverse cylinders through heavy
duty roller chain. The chain connects to heavy trunnion bars to which the top
head is fastened with high alloy pins.
Drilling is performed in the slow feed mode and includes adjustable pressure
reliefs for pulldown and holdback to insure correct bit loading. Feed and
rotation are independently controlled. The rapid feed circuit can be used in
conjunction with the slow feed system to provide high tripping speeds when
conditions allow. Drill pipe weight adds to the overall speed of the rapid feed-
down system.
Feed Cylinder: (2) 6.00" Bore x 2 3/4" Rod x 180" Stroke (152 mm x 70 mm
x 4,572 mm)
Hoist Capacity: 93,700 lb (42,502 kg)
Hoist Speed-Slow Feed: 10.2 fpm (3.1 mpm)
Hoist Speed-Rapid Feed: 113 fpm (34.4 mpm)
Hoist Speed-Rapid & Slow: 123.2 fpm (37.6 mpm)
Upper Chain: (2) Double Capacity 180DC - 2-1/4" pitch (57.2 mm)
Chain Capacity (per strand): 163,000 lb Avg Ultimate Strength (73,937 kg)
Pulldown Capacity: 28,000 lb (12,698 kg)
Pulldown Speed-Slow Feed: 8.0 fpm (2.4 mpm)
Pulldown Speed-Rapid Feed: 89 fpm (27.1 mpm)
Pulldown Speed-Rapid & Slow: 97 fpm (29.6 mpm)
Lower Chain: (2) ANSI 160H - 2" pitch (50.8 mm)
Chain Capacity (per strand): 71,600 lb Avg Ultimate Strength (32,478 kg)
A-4 T685WS
Detailed Rig Specifications
the use of elevator links for lifting heavy strings of casing with the hoist
system.
T685WS A-5
Detailed Rig Specifications
has a 22" (558 mm) diameter opening with all slips removed. The slipbox is
hinged to swing-open permitting easy access to the borehole beneath the
mast. A hydraulic holding wrench with 3-7/8" flats is included.
For Sliding Angle Mast applications only.
Schramm Air-Control
Schramm's patented controls monitor cooling system temperature and
compressor volume requirements and match fan speed and compressor inlet
valve to provide maximum power efficiency. Smaller hammers often require
A-6 T685WS
Detailed Rig Specifications
The Air-Control System also senses the deck engine systems to provide
horsepower limiting capability. If momentary hydraulic power requirements
are high, the Air-Control system will vary the output volume to avoid a situation
where HP demand exceeds the available engine horsepower.
T685WS A-7
Detailed Rig Specifications
Does not require refilling special fluids (urea) to maintain the exhaust
emissions system.
Local regulations dictate what loads are permitted on what axles. Care must
be exercised in specifying optional equipment.
A-8 T685WS
Detailed Rig Specifications
Foam Injection
Diaphragm type electric pulse pump injects drill foam and additives into intake
manifold of water injection pump, includes metering valve in control panel and
5 gal (19 l) foam container.
Model: Blue and White
Minimum Flow: 1.2 gph (5 lph)
Maximum Flow: 13.2 gph (50 lph)
No Pipe Rack
Side pipe rack not available.
T685WS A-9
Detailed Rig Specifications
equipped machines. By shifting the valve and opening the purge line, high
pressure air is directed into the inner tube of the drill string to clear
obstructions. Use for 4 1/2" RC pipe.
Cyclone, LH Mounted
A swing-arm mounted cyclone is located at the rear of the machine in clear
view of the operator. The arm swings to position the cyclone on the left side
of the rig. Cyclone assembly reduces the velocity of the cuttings to allow
complete sample recovery. Includes 3" x 50' RC hose.
This option makes the drill rig over width. The cyclone must be removed for
highway transport.
Holdback/Rotation Scales
Plastic nameplate rings added to the holdback and rotation gauges to convert
psi readings. Converts to lbs for the pullback gauge & ft/lbs for the rotation
gauge.
For use with 93,700# mast and 40.6 cu in motors only.
A-10 T685WS
Filters
T685WS B-1
Page intentionally blank
Truck/Carrier OEM Specifications & Book Reference
Compressor Information
Compressor Serial #: 201008180058
Pressure Vessels
Air/Oil Tank Serial #: 648356
Electrical
PLC Serial #: G125-3223
Gearboxes
Pump Drive Gearbox Serial #: Funk YZD283C118760M (1040-0050)
Rotation Gearbox Serial #: Schramm S/NJ125-3223 (0870-0119)
CAUTION
Welding on the drill rig can damage the engine electronic control module.
Please consult Schramm prior to welding.
T685WS C-1
Page intentionally blank
Hoses
BLOWDOWN VALVE
Part # Dia. End Length Description Note Qty
GEARBOX JUNCTION PLATE TO
2826-1639 16 37S 245 HOSE HYD 100R16 16X245 37S 1
BULKHEAD
2826-1504 16 37S 265 HOSE HYD 100R16 16X265 37S AIR VALVE TO JUNCTION PLATE 1
2826-0864 16 37S 46 HOSE HYD 100R16 16X 46 37S TUBING TO BULKHEAD JUMPER 2
2826-1126 4 37S 307 HOSE HYD 100R16 04X307 37S C VALVE TO JUNCTION PLATE 2
2826-1126 4 37S 307 HOSE HYD 100R16 04X307 37S C VALVE TO JUNCTION PLATE 2
2826-0632 6 37S 120 HOSE HYD 100R16 06X120 37S CYL BUTT TO JUNCTION PLATE 1
2826-0635 6 37S 134 HOSE HYD 100R16 06X134 37S CYL ROD TO JUNCTION PLATE 1
T685WS D-1
Hoses
2826-0530 4 S90 127 HOSE HYD 100R16 04X127 S90 #2 PORT 2258 0254 TO CMX 'LS' 1
2826-0398 4 37S 120 HOSE HYD 100R16 04X120 37S FAN PUMP TO SERVO VLV INLET 1
2826-0442 4 37S 150 HOSE HYD 100R16 04X150 37S CMX PRESSURE TO GAUGE 1
2826-0943 8 37S 248 HOSE HYD 100R16 08X248 37S WATER NEEDLE VALVE TO MOTOR 1
2826-1113 12 37S 295 HOSE HYD 100R16 12X295 37S WATER INJ CV TO MAST 1
2826-0413 4 37S 60 HOSE HYD 100R16 04X 60 37S CHECK VALVE TO W.I. GAUGE 2
2826-0625 4 S90 104 HOSE HYD 100R16 04X104 S90 AIR VLV TO CV 2
2826-0625 4 S90 104 HOSE HYD 100R16 04X104 S90 AIR VLV TO CV 2
2826-1171 6 S90 165 HOSE HYD 100R16 06X165 S90 RIGHT OUTR VLV TO CV 2
2826-1171 6 S90 165 HOSE HYD 100R16 06X165 S90 RIGHT OUTR VLV TO CV 2
2826-0844 6 37S 173 HOSE HYD 100R16 06X173 37S MAST TILT VLV TO BUTT ENDS 2
2826-0844 6 37S 173 HOSE HYD 100R16 06X173 37S MAST TILT VLV TO BUTT ENDS 2
2826-0669 6 37S 200 HOSE HYD 100R16 06X200 37S MAST TILT VLV TO ROD ENDS 2
D-2 T685WS
Hoses
2826-0669 6 37S 200 HOSE HYD 100R16 06X200 37S MAST TILT VLV TO ROD ENDS 2
2826-0850 12 37S 180 HOSE HYD 100R16 12X180 37S SF VLV RETURN TO MANIFOLD 2
2826-0850 12 37S 180 HOSE HYD 100R16 12X180 37S WI VLV RETURN TO MANIFOLD 2
2826-0905 6 S90 114 HOSE HYD 100R16 06X114 S90 LH OUTR VLV TO CHECK VLV 4
2826-0905 6 S90 114 HOSE HYD 100R16 06X114 S90 LH OUTR VLV TO CHECK VLV 4
2826-0584 4 S90 160 HOSE HYD 100R16 04X160 S90 'B' CMX TO HRC ROT CB 5
2826-0584 4 S90 160 HOSE HYD 100R16 04X160 S90 'B' CMX TO HRC ROT CB 5
2826-0584 4 S90 160 HOSE HYD 100R16 04X160 S90 'B' CMX TO HRC RF CT 5
2826-0584 4 S90 160 HOSE HYD 100R16 04X160 S90 'B' CMX TO HRC RF CT 5
2826-0584 4 S90 160 HOSE HYD 100R16 04X160 S90 'B' CMX TO HRC WINCH CB 5
2826-0652 4 37S 168 HOSE HYD 100R16 04X168 37S A' CMX TO HRC ROT CT 7
2826-0652 4 37S 168 HOSE HYD 100R16 04X168 37S A' CMX TO HRC ROT CT 7
2826-0652 4 37S 168 HOSE HYD 100R16 04X168 37S A' CMX TO HRC RF CB 7
2826-0652 4 37S 168 HOSE HYD 100R16 04X168 37S A' CMX TO HRC RF CB 7
2826-0652 4 37S 168 HOSE HYD 100R16 04X168 37S A' CMX TO HRC WINCH CT 7
2826-0652 4 37S 168 HOSE HYD 100R16 04X168 37S BALL VLV TO LUBE PUMP 7
2826-0652 4 37S 168 HOSE HYD 100R16 04X168 37S LUBE NEEDLE VLV TO PUMP 7
T685WS D-3
Hoses
CYCLONE, LH MOUNTED
Part # Dia. End Length Description Note Qty
2826-0877 4 S90 43 HOSE HYD 100R16 04X 43 S90 HANSEN FTG TO VLV 1
2826-1313 4 37S 54 HOSE HYD 100R16 04X 54 37S DUMP VLV CYL BUTT JUMPER 1
2826-1039 4 37S 36 HOSE HYD 100R16 04X 36 37S DUMP VLV CYL ROD JUMPER 1
1184-0203 48 0 600 HOSE ASY REV CIRC 3" X 50' STORE ON RIG 1
D-4 T685WS
Hoses
T685WS D-5
Hoses
2826-0331 6 37S 100 HOSE HYD 100R16 06X100 37S BREAKOUT CYL (RAM) TO TUBING 1
2826-0733 6 37S 92 HOSE HYD 100R16 06X 92 37S BREAKOUT CUL (BUTT) TO TUBING 1
2826-0580 6 S90 76 HOSE HYD 100R16 06X 76 S90 EXTEND CYL RAM TO JB TUBING 1
2826-0732 6 S90 80 HOSE HYD 100R16 06X 80 S90 EXTEND CYL BUTT TO JB TUBING 1
2826-1633 6 37S 53 HOSE HYD 100R16 06X 53 37S TUBING TO JUNCTION PLATE 1
2826-1033 4 S90 28 HOSE HYD 100R16 04X 28 S90 TROUGH CHECK VLV TO CYL (BUTT) 1
2826-1039 4 37S 36 HOSE HYD 100R16 04X 36 37S TROUGH CHECK VLV TO CYL (RAM) 1
2826-0565 4 S90 17 HOSE HYD 100R16 04X 17 S90 SLIDE CYL JUMPER 1
2826-0845 6 S90 240 HOSE HYD 100R16 06X240 S90 RELIEF VLV TO MAST TUBING 1
2826-1316 6 S90 44 HOSE HYD 100R16 06X 44 S90 WORM DRIVE MTR TO JB TUBING 2
2826-1316 6 S90 44 HOSE HYD 100R16 06X 44 S90 WORM DRIVE MTR TO JB TUBING 2
2826-1156 16 S90 47 HOSE HYD 100R13 16X 47 S90 TUBING TO TRAVERSE CYL (BUTT) 2
2826-1156 16 S90 47 HOSE HYD 100R13 16X 47 S90 TUBING TO TRAVERSE CYL (BUTT) 2
2826-1218 16 S90 37 HOSE HYD 100R13 16X 37 S90 TUBING TO TRAVERSE CYL (RAM) 2
2826-1218 16 S90 37 HOSE HYD 100R13 16X 37 S90 TUBING TO TRAVERSE CYL (RAM) 2
2826-1502 8 37S 26 HOSE HYD 100R13 08X 26 37S TRAVERSE CYL JUMPER HOSES 2
2826-1502 8 37S 26 HOSE HYD 100R13 08X 26 37S TRAVERSE CYL JUMPER HOSES 2
D-6 T685WS
Hoses
2826-1471 8 37S 22 HOSE HYD 100R13 08X 22 37S ROTATION JUMPER HOSES 2
2826-1471 8 37S 22 HOSE HYD 100R13 08X 22 37S ROTATION JUMPER HOSES 2
1184-0189 32 NPT 240 HOSE AIR 3000# 32X240 NPT HOSE SUPT TO AIR PIPING 2
1184-0189 32 NPT 240 HOSE AIR 3000# 32X240 NPT HOSE SUPT TO AIR VALVE 2
2826-0830 6 37S 48 HOSE HYD 100R16 06X 48 37S TUBING TO JUNCTION PLATE 3
2826-0830 6 37S 48 HOSE HYD 100R16 06X 48 37S TUBING TO JUNCTION PLATE 3
2826-0830 6 37S 48 HOSE HYD 100R16 06X 48 37S TUBING TO JUNCTION PLATE 3
2826-0617 6 37S 86 HOSE HYD 100R16 06X 86 37S HOLDING WRENCH TUBING TO JP 4
2826-0617 6 37S 86 HOSE HYD 100R16 06X 86 37S HOLDING WRENCH TUBING TO JP 4
2826-1141 16 S90 225 HOSE HYD 100R13 16X225 S90 ROTATION HOSES 4
2826-1141 16 S90 225 HOSE HYD 100R13 16X225 S90 ROTATION HOSES 4
2826-1141 16 S90 225 HOSE HYD 100R13 16X225 S90 ROTATION HOSES 4
2826-1141 16 S90 225 HOSE HYD 100R13 16X225 S90 ROTATION HOSES 4
2826-0650 6 37S 325 HOSE HYD 100R16 06X325 37S JP TO JB VLV (CNTRL PNL) 6
T685WS D-7
Hoses
2826-0650 6 37S 325 HOSE HYD 100R16 06X325 37S JP TO JB VLV (CNTRL PNL) 6
2826-0650 6 37S 325 HOSE HYD 100R16 06X325 37S JP TO JB VLV (CNTRL PNL) 6
2826-0650 6 37S 325 HOSE HYD 100R16 06X325 37S JP TO JB VLV (CNTRL PNL) 6
2826-0650 6 37S 325 HOSE HYD 100R16 06X325 37S JP TO B/O CYL VLV (CNTRL PNL) 6
2826-0650 6 37S 325 HOSE HYD 100R16 06X325 37S JP TO B/O CYL VLV (CNTRL PNL) 6
2826-1689 16 37S 310 HOSE HYD 100R13 16X310 37S RAPID FEED CMX VLV TO JP 8
2826-1689 16 37S 310 HOSE HYD 100R13 16X310 37S RAPID FEED CMX VLV TO JP 8
2826-1689 16 37S 310 HOSE HYD 100R13 16X310 37S RAPID FEED CMX VLV TO JP 8
2826-1689 16 37S 310 HOSE HYD 100R13 16X310 37S RAPID FEED CMX VLV TO JP 8
2826-1689 16 37S 310 HOSE HYD 100R13 16X310 37S ROT CMX VLV TO JP 8
2826-1689 16 37S 310 HOSE HYD 100R13 16X310 37S ROT CMX VLV TO JP 8
2826-1689 16 37S 310 HOSE HYD 100R13 16X310 37S ROT CMX VLV TO JP 8
2826-1689 16 37S 310 HOSE HYD 100R13 16X310 37S ROT CMX VLV TO JP 8
2826-0339 6 37S 395 HOSE HYD 100R16 06X395 37S VALVES TO CHECK VALVES 4
2826-0339 6 37S 395 HOSE HYD 100R16 06X395 37S VALVES TO CHECK VALVES 4
2826-0339 6 37S 395 HOSE HYD 100R16 06X395 37S VALVES TO CHECK VALVES 4
2826-0339 6 37S 395 HOSE HYD 100R16 06X395 37S VALVES TO CHECK VALVES 4
2826-0365 4 S90 22 HOSE HYD 100R16 04X 22 S90 CHECK VALVES TO CYLINDERS 4
2826-0365 4 S90 22 HOSE HYD 100R16 04X 22 S90 CHECK VALVES TO CYLINDERS 4
2826-0365 4 S90 22 HOSE HYD 100R16 04X 22 S90 CHECK VALVES TO CYLINDERS 4
2826-0365 4 S90 22 HOSE HYD 100R16 04X 22 S90 CHECK VALVES TO CYLINDERS 4
D-8 T685WS
Hoses
SCHRAMM AIR-CONTROL
Part # Dia. End Length Description Note Qty
PORT 1 OF 2767-0123 TO ROD END
2826-0586 4 S90 52 HOSE HYD 100R16 04X 52 S90 1
OF COMP CYL
1666-0326 8 37S 130 HOSE A/O MGTECH 08X130 S90 MIIN PRESS VLV TO RBDV INLET 1
1666-0255 8 S90 50 HOSE A/O MGTECH 08X 50 S90 RBDV OUTLET TO MUFFLER 1
2826-9900 4 TBD 0 HOSE HYD 100R16 04X--- TBD DISCONNECT BRKT TO SPLITTER 1
2826-0824 4 37S 14 HOSE HYD 100R16 04X 14 37S JUMPER HOSE ON MOTOR 2
2826-0824 4 37S 14 HOSE HYD 100R16 04X 14 37S JUMPER HOSE ON MOTOR 2
T685WS D-9
Hoses
SWIVEL&FLOATINGSHAFT FOR5"HEAD
Part # Dia. End Length Description Note Qty
1184-0235 32 NPT 60 HOSE AIR 3000# 32X 60 NPT SWIVEL TO HOSE SUPPORT 1
2826-0517 12 S90 40 HOSE HYD 100R16 12X 40 S90 FUEL INJ PUMP TO FILTER 1
1184-0190 32 NPT 84 HOSE AIR 3000# 32X 84 NPT AIR VALVE TO MAST 1
2826-0881 4 37S 80 HOSE HYD 100R16 04X 80 37S LS CMX TO LS ROT COMP 1
2826-1574 4 S90 86 HOSE HYD 100R16 04X 86 S90 ROT CMX C1 TO ROT COMP C1 1
2826-0416 4 37S 102 HOSE HYD 100R16 04X102 37S CMX DRAIN TO TANK 1
2826-0398 4 37S 120 HOSE HYD 100R16 04X120 37S ENG VENT TO TOP OF COOLER 1
2826-0742 6 S90 27 HOSE HYD 100R16 06X 27 S90 SF VALVE 'B' TO DF REG BTM 1
D-10 T685WS
Hoses
2826-0437 12 S90 22 HOSE HYD 100R16 12X 22 S90 HAND PUMP TO FILTER #4 1
2826-0631 12 37S 76 HOSE HYD 100R16 12X 76 37S HAND PUMP INLET 1
2826-1657 16 37S 144 HOSE HYD 100R16 16X144 37S FAN RETURN TO MANIFOLD #1 1
2826-0961 16 37S 34 HOSE HYD 100R13 16X 34 37S RH ROT/RF PUMP TO CMX BOTTOM 1
2826-1029 16 37S 185 HOSE HYD 100R13 16X185 37S FAN MOTOR TO PUMP 1
2826-1193 20 37S 100 HOSE HYD 100R 2 20X100 37S CMX RETURN TO MANIFOLD #1 1
2826-0933 20 37S 38 HOSE SUC 100R 4 20X 38 37S FUEL PUMP TO FILTER 1
2826-1716 20 37S 195 HOSE SUC 100R 4 20X195 37S FUEL TANK TO FILTER 1
2826-2025 24 FL45 16 HOSE SUC 100R 4 24X 16 FL45 0566-0087 MANIFOLD TO FILTER #3 1
2826-0786 32 NPT 86 HOSE SUC 100R 4 32X 86 NPT FAN PUMP TO GATE VALVE #3 1
2826-0527 6 37S 31 HOSE HYD 100R16 06X 31 37S HRC RETURN TO 0130 MANIFOLD 1
T685WS D-11
Hoses
2826-0413 4 37S 60 HOSE HYD 100R16 04X 60 37S HB GAUGE TO #2 PORT ON 0394 1
2826-0840 4 S90 80 HOSE HYD 100R16 04X 80 S90 ROT CMX C2 TO ROT COMP C2 1
2826-1301 12 37S 37 HOSE HYD 100R16 12X 37 37S FUEL TNK CROSS-OVER HOSE 2
2826-1301 12 37S 37 HOSE HYD 100R16 12X 37 37S ENGINE OIL DRAIN 2
2826-0369 4 37S 16 HOSE HYD 100R16 04X 16 37S AIR VLV BUTT TO C2 CV 2
2826-0371 4 37S 24 HOSE HYD 100R16 04X 24 37S CASE DRAIN FILTER TO GAUGE 2
2826-0877 4 S90 43 HOSE HYD 100R16 04X 43 S90 LH REAR OUTRIGGER VALVE TO CV 2
2826-0877 4 S90 43 HOSE HYD 100R16 04X 43 S90 LH REAR OUTRIGGER VALVE TO CV 2
2826-0391 8 37S 80 HOSE HYD 100R16 08X 80 37S LH ROT & RF PUMP CASE DRAIN 2
2826-0978 12 37S 29 HOSE HYD 100R16 12X 29 37S FUEL COOLER TO TANK 2
2826-1460 12 37S 220 HOSE HYD 100R16 12X220 37S WATER INJ TO AIR VALVE 2
2826-0875 12 37S 120 HOSE HYD 100R13 12X120 37S WINCH CMX TO WINCH 2
2826-0875 12 37S 120 HOSE HYD 100R13 12X120 37S WINCH CMX TO WINCH 2
D-12 T685WS
Hoses
2826-1692 24 FL45 32 HOSE SUC 100R 4 24X 32 FL45 0566-0087 MANIFOLD TO FILTER #1 2
2826-1692 24 FL45 32 HOSE SUC 100R 4 24X 32 FL45 0566-0087 MANIFOLD TO FILTER #2 2
2826-0644 4 37S 19 HOSE HYD 100R16 04X 19 37S AIR VLV ROD TO C1 CV 3
2826-0644 4 37S 19 HOSE HYD 100R16 04X 19 37S FUEL PRIMER PUMP IN FROM CV 3
2826-0587 4 S90 31 HOSE HYD 100R16 04X 31 S90 CV TO ROD END RH OUTRIGGER 3
2826-0587 4 S90 31 HOSE HYD 100R16 04X 31 S90 CV TO BUTT END RH OUTRIGGER 3
2826-0587 4 S90 31 HOSE HYD 100R16 04X 31 S90 #3 FAN SELECTOR TO HRC RETURN 3
2826-0532 4 S90 49 HOSE HYD 100R16 04X 49 S90 FEED COMP T PORT TO TANK 3
2826-0532 4 S90 49 HOSE HYD 100R16 04X 49 S90 ROT COMP T PORT TO TANK 3
2826-0532 4 S90 49 HOSE HYD 100R16 04X 49 S90 FAN COMP "T" PORT TO TANK 3
1184-0016 32 NPT 43 HOSE AIR 100R 2 32X 43 NPT JUMPER HOSE ON AIR/OIL TANK 3
1184-0016 32 NPT 43 HOSE AIR 100R 2 32X 43 NPT AIR LINE TO AIR VALVE 3
T685WS D-13
Hoses
2826-0944 4 37S 42 HOSE HYD 100R16 04X 42 37S FAN PUMP LS TO FAN COMP VLV LS 4
JUMPER LS RH TO LH ROT/RF
2826-0944 4 37S 42 HOSE HYD 100R16 04X 42 37S 4
PUMPS
PIPE TO PIPE (TOP PIPE TO OUT-
1666-0369 20 37S 48 HOSE A/O MGTECH 20X 48 37S 4
SIDE PIPE)
PIPE TO PIPE (TOP PIPE TO OUT-
1666-0369 20 37S 48 HOSE A/O MGTECH 20X 48 37S 4
SIDE PIPE)
PIPE TO PIPE (BOTTOM PIPE TO
1666-0369 20 37S 48 HOSE A/O MGTECH 20X 48 37S 4
INSIDE PIPE)
PIPE TO PIPE (BOTTOM PIPE TO
1666-0369 20 37S 48 HOSE A/O MGTECH 20X 48 37S 4
INSIDE PIPE)
2826-0565 4 S90 17 HOSE HYD 100R16 04X 17 S90 LS ROT COMP TO RF LS COMP 5
2826-0565 4 S90 17 HOSE HYD 100R16 04X 17 S90 LUB NEEDLE VALVE TO GAUGE 5
2826-0369 4 37S 16 HOSE HYD 100R16 04X 16 37S RELIEF VLV TO LUB TANK 1
2826-1315 6 S90 12 HOSE HYD 100R16 06X 12 S90 LH MTR CASE DRAIN TO TEE 1
2826-1015 6 S90 40 HOSE HYD 100R16 06X 40 S90 RH MTR CASE DRAIN TO TEE 1
D-14 T685WS
Hoses
2826-0437 12 S90 22 HOSE HYD 100R16 12X 22 S90 RELIEF VLV TO PMP SUCTION 1
2826-0634 6 37S 166 HOSE HYD 100R16 06X166 37S WINCH CASE DRAIN 1
T685WS D-15
Page intentionally blank
Decals
T685WS E-1
Decals
E-2 T685WS
Nameplates
T685WS F-1
© Schramm, Inc. 2010
All rights reserved. Schramm, i-Control, and Telemast are registered trademarks of Schramm, Inc.
www.Schramminc.com