Professional Documents
Culture Documents
NSXSZ2ELHREV
NSXSZ2ELHREV
SERVICE MANUAL
COMPACT DISC STEREO BASIC TAPE MECHANISM : ZZM-2 APR1NC
SYSTEM BASIC CD MECHANISM : 3ZG-3 E8NC
CD REMOTE
SYSTEM SPEAKER
CASSEIVER CONTROLLER
NSX-SZ2 CX–NSZ2 SX-NSZ2 RC–AAS08
• This Service Manual is the "Revision Publishing" and replaces "Simple Manual"
NSX-SZ2(LH), (S/M Code No. 09-00A-433-7T4).
N
SIO
VI
RE
TA
DA
–2–
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle. CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
VARNING! LUOKAN 1 LASER LAITE
Om apparaten används på annat sätt än vad som KLASS 1 LASER APPARAT
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
Solder
–3–
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
MAIN C.B
1 Remove the AC power cord.
2 Connect a discharging resistor at an end of lead wire that D101
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3 Contact the other end of the discharging resistor to the 3 4
positive (+) side (+VH) of C101. (For two seconds) C101 C102
4 Contact the same end of the discharging resistor as step
3 to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5 Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope. 2 2
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
–4–
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
FRONT C.B
PU
M
CO
RO
18 % VSS
IC
15
M
C113 MICRO-
COMPUTER
* VDD
C113
FRONT C.B
Short with tweezers.
Fig-2-2
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
–5–
ELECTRICAL MAIN PARTS LIST
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
IC C61 87-010-260-080 CAP, ELECT 47-25V
C101 87-012-284-080 CAP, U 6800P-50
87-A21-591-010 C-IC,LC78641NE-D C102 87-012-284-080 CAP, U 6800P-50
87-A21-722-010 IC,LA6548D C103 87-010-544-080 CAP, ELECT 0.1-50V
87-A21-419-040 C-IC,NJM14558MD-TE2 C104 87-010-544-080 CAP, ELECT 0.1-50V
8A-NEC-602-010 C-IC,M38B57MCH-E249FP
87-070-083-010 IC,GP1U281X C105 87-012-282-080 CAP, U 4700P-50
C106 87-012-282-080 CAP, U 4700P-50
87-A21-443-040 C-IC,M62495AFP C107 87-010-403-080 CAP, ELECT 3.3-50V
87-A21-560-010 IC,LA1844L-A C108 87-010-403-080 CAP, ELECT 3.3-50V
87-070-127-110 IC,LC72131 D C111 87-010-406-080 CAP, ELECT 22-50
87-A21-381-040 C-IC,LA9235M
C112 87-010-406-080 CAP, ELECT 22-50
C113 87-012-195-080 C-CAP,U 100P-50CH
TRANSISTOR C114 87-012-195-080 C-CAP,U 100P-50CH
C117 87-012-286-080 CAP, U 0.01-25
87-026-609-080 TR,KTA1266GR C118 87-012-286-080 CAP, U 0.01-25
89-213-702-010 TR,2SB1370E
87-026-610-080 TR,KTC3198GR C119 87-012-286-080 CAP, U 0.01-25
87-A30-076-080 C-TR,2SC3052F C120 87-012-286-080 CAP, U 0.01-25
87-A30-075-080 C-TR,2SA1235F C125 87-010-759-080 C-CAP,U, 0.1-25F
C126 87-010-759-080 C-CAP,U, 0.1-25F
87-A30-256-010 TR,2SD1933 C127 87-010-759-080 C-CAP,U, 0.1-25F
87-A30-255-010 TR,2SB1342
87-A30-104-080 C-TR,RT1N 441C C128 87-010-759-080 C-CAP,U, 0.1-25F
87-A30-520-080 TR,2SC5342Y C140 87-010-190-080 S CHIP F 0.01
87-A30-090-080 FET,2SK2541 C301 87-010-374-080 CAP, ELECT 47-10V
C302 87-010-759-080 C-CAP,U, 0.1-25F
87-A30-091-080 FET,2SJ460 C303 87-010-260-080 CAP, ELECT 47-25V
87-A30-062-080 C-TR,KRC104S
87-A30-318-080 TR,CSA952K C304 87-010-260-080 CAP, ELECT 47-25V
87-A30-492-080 TR,2SC5343G C305 87-012-286-080 CAP, U 0.01-25
87-A30-234-080 TR,CSC4115BC C306 87-010-405-080 CAP, ELECT 10-50V
C307 87-010-263-080 CAP, ELECT 100-10V
87-A30-521-080 C-TR,2SC5345S(O) C308 87-012-349-080 C-CAP,S 1000P-50 CH
87-A30-489-080 C-TR,KRA107S
89-503-602-080 C-FET,2SK360E C309 87-010-546-080 CAP, ELECT 0.33-50V
89-327-143-080 C-TR,2SC27140 C310 87-010-401-080 CAP, ELECT 1-50V
C311 87-012-193-080 C-CAP,U 82P-50 CH
C312 87-012-286-080 CAP, U 0.01-25
DIODE C313 87-010-260-080 CAP, ELECT 47-25V
–6–
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
C374 87-010-236-080 CAP,E 1000-10 SME C783 87-012-286-080 CAP, U 0.01-25
C375 87-010-759-080 C-CAP,U, 0.1-25F C784 87-012-286-080 CAP, U 0.01-25
C376 87-010-263-080 CAP, ELECT 100-10V C785 87-012-286-080 CAP, U 0.01-25
C377 87-010-759-080 C-CAP,U, 0.1-25F C786 87-012-286-080 CAP, U 0.01-25
C378 87-010-759-080 C-CAP,U, 0.1-25F C788 87-012-167-080 C-CAP,U 5P-50 CH
C412 87-010-405-080 CAP, ELECT 10-50V C815 87-010-400-080 CAP, ELECT 0.47-50V
C413 87-010-197-080 CAP, CHIP 0.01 DM C816 87-010-400-080 CAP, ELECT 0.47-50V
C421 87-012-275-080 C-CAP,U 1200P-50 B C821 87-010-405-080 CAP, ELECT 10-50V
C422 87-012-275-080 C-CAP,U 1200P-50 B C823 87-010-177-080 C-CAP,S 820P-50 SL
C423 87-012-274-080 CHIP CAP,U 1000P-50B C824 87-010-404-080 CAP, ELECT 4.7-50V
C606 87-012-275-080 C-CAP,U 1200P-50 B C924 87-012-174-080 CAP CHIP CERA SS 12P CHJ
C609 87-010-785-080 C-CAP,U0.015-25BK C927 87-012-195-080 C-CAP,U 100P-50CH
C610 87-010-785-080 C-CAP,U0.015-25BK C961 87-012-170-080 C-CAP,U 8P-50 CH
C611 87-010-545-080 CAP, ELECT 0.22-50V C962 87-010-401-080 CAP, ELECT 1-50V
C612 87-010-545-080 CAP, ELECT 0.22-50V C971 87-010-381-080 CAP, ELECT 330-16V
C613 87-010-545-080 CAP, ELECT 0.22-50V C972 87-010-404-080 CAP, ELECT 4.7-50V
C614 87-010-545-080 CAP, ELECT 0.22-50V C973 87-012-286-080 CAP, U 0.01-25
C615 87-012-172-080 CAPACITOR CHIP U 10P CH C974 87-012-286-080 CAP, U 0.01-25
C616 87-010-248-080 CAP, ELECT 220-10V C979 87-012-195-080 C-CAP,U 100P-50CH
C617 87-010-221-080 CAP, ELECT 470-10V C981 87-010-260-080 CAP, ELECT 47-25V
–7–
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
C991 87-012-176-080 CAP 15P C509 87-010-404-040 CAP,E 4.7-50 SME
C992 87-012-176-080 CAP 15P C510 87-010-404-040 CAP,E 4.7-50 SME
C993 87-012-274-080 CHIP CAP,U 1000P-50B C511 87-010-759-080 C-CAP,U, 0.1-25F
C994 87-012-195-080 C-CAP,U 100P-50CH C512 87-010-263-040 CAP,E 100-10 SME
C995 87-012-274-080 CHIP CAP,U 1000P-50B C514 87-012-274-080 CHIP CAP,U 1000P-50B
J101 87-A60-602-010 JACK,DIA6.3 BLK ST W/SW TC C541 87-016-459-040 CAP,E 470-10 SMG
J103 87-A61-452-010 TERMINAL,SP 4P(MSC) C590 87-010-384-040 CAP,E 100-25 SME
J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN CN201 87-A60-062-010 CONN,05P V 9604S-05C
J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02 CN501 87-A60-673-010 CONN,9P H 2MM JMT
! JW1 87-A90-093-080 PROTECTOR,3A 491SERIES 60V CNA501 8Z-ZM2-601-01 CONN ASSY,9P ZZM-2
! JW2 87-A90-093-080 PROTECTOR,3A 491SERIES 60V FL501 8A-NEC-601-010 FL,HNA-10SS15T
L101 87-A50-610-010 COIL,1UH K(MDEC) L501 87-A50-655-010 COIL,CLK 4.19MHZ (TOKO)7KLY
L102 87-A50-610-010 COIL,1UH K(MDEC) S201 87-A90-095-080 SW,TACT EVQ11G04M
L451 87-007-342-010 COIL,OSC 85K BIAS S202 87-A90-095-080 SW,TACT EVQ11G04M
L801 87-A50-608-010 COIL,FM DET-N(TOK) S203 87-A90-095-080 SW,TACT EVQ11G04M
–8–
CHIP RESISTOR PART CODE
–9–
TRANSISTOR ILLUSTRATION
E C B E C B E C B B C E
S C
D B
G E
S D G B C E
E C B
2SC5343G
– 10 –
WIRING 1 ( MAIN / FRONT )
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
11
SCHEMATIC DIAGRAM – 1 (MAIN 1/3: AMP SECTION)
– 12 –
SCHEMATIC DIAGRAM – 2 (MAIN 2/3: TUNER SECTION )
– 13 –
SCHEMATIC DIAGRAM – 3 (MAIN 3/3: CD SECTION / CD DRIVE )
– 14 –
SCHEMATIC DIAGRAM – 4 (FRONT / LOAD)
– 15 –
WIRING – 2 ( DECK )
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
– 16 –
WIRING – 3 ( CD LOAD / CD DRIVE )
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
– 17 –
IC BLOCK DIAGRAM
– 18 –
FL (HNA-10SS15T) GRID ASSIGNMENT & ANODE CONNECTION
GRID ASSIGNMENT
ANODE CONNECTION
– 19 –
IC DESCRIPTION
IC, M38B57MCH - E249FP
Pin No. Pin Name I/O Description
1 NC — Not connected.
2 I-HOLD I Hold input.
3 I-TRAY SW I CD tray SW AD input.
4 I-D-SW I CD door open/close AD detection input (Not used).
5 I-KEY2 I Key AD input 2.
6 I-KEY1 I Key AD input 1.
7 O-DSP DATA — Not used.
8 O-MOTOR O Cassette deck motor control output.
9 I-RMC I System remote control signal input. (Active "L")
10 RESET I Reset input for MICON.
11 I-STEREO I Tuner stereo detect input.
– 20 –
Pin No. Pin Name I/O Description
42 G1 O FL grid output (G1).
43 P22 — Not used.
44 P21 — Not used.
45 P20 O FL segment output (P20).
46 P19 O FL segment output (P19).
47 P18 O FL segment output (P18).
48 P17 O FL segment output (P17).
49 P16 O FL segment output (P16).
50 P15 O FL segment output (P15).
51 P14 O FL segment output (P14).
52 P13 O FL segment output (P13).
53 P12 O FL segment output (P12).
54 P11 O FL segment output (P11).
55 P10 O FL segment output (P10).
56 P9 O FL segment output (P9).
57 P8 O FL segment output (P8).
58 P7 O FL segment output (P7).
59 P6 O FL segment output (P6).
60 P5 O FL segment output (P5).
61 P4 O FL segment output (P4).
62 I-TU3/P3 I/O TU3 diode input/FL segment output (P3).
63 I-TU2/P2 I/O TU2 diode input/FL segment output (P2).
64 I-TU1/P1 I/O TU1 diode input/FL segment output (P1).
65 NC — Not connected.
66 NC — Not connected.
67 I-SUB Q (CD) I SUB-Q data input.
68 O-CD.CE O CD data chip enable output.
69 I-WRQ (CD) I CD WRQ input.
70 O-CL (CD) O CD IC control clock output.
71 O-DATA (CD) O CD IC control data output.
72 I-TUNE/IFC I Tuner SD detection input/Tuner IF count input.
73 AVSS — Connected to GND.
74 VREF — Power supply.
75 I-DRF (CD) I CD DRF input.
76 NC — Not connected.
77 NC — Not connected.
78 NC — Not connected.
79 NC — Not connected.
80 I-TP.SW I Deck mechanism SW AD input.
– 21 –
IC, LC78641NE-D
Pin No. Pin Name I/O Description
1 PDO1 O Internal VCO control phase comparator output pin. (Pull down)
Internal VCO control phase comparator output pin.
2 PDO2 O
OFF for rough servo, ON for phase servo. (Pull down)
3 VVSS — Internal VCO ground pin.
4 PCKIST — PDO output current adjustment resistor connection pin.
5 VVDD — Internal VCO power supply pin.
6 FR — VCO frequency range adjustment resistor connection pin. (Pull up)
7 HFL I Mirror detection signal input pin.
8 SLCIST — SLCO output current adjustment resistor connection pin.
9 SLCO O Control output.
10 EFMIN I EFM signal input pin.
11 JITTV O Jitter detection monitor pin. (Not used)
12 JITTC O Jitter detection monitor pin. (Pull down)
13 BH I BH signal input pin. (Connected to GND)
14 PH (RFENV) I PH signal or RFENV signal input pin.
15 FE I FE signal input pin.
16 TE I TE signal input pin.
17 VREF I VREF input pin.
18 ADAVDD — Servo A/D, D/A power supply pin.
19 ADAVSS — Servo A/D, D/A ground pin.
20 PHREF O PH reference output pin. (Not used)
21 BHREF O BH reference output pin. (Not used)
22 TBLO O Tracking balance output pin.
23 TDO O Tracking control output pin.
24 FDO O Focus control output pin.
25 SPDO O Spindle control output pin.
26 SLDO O Thread control output pin.
27 FG I/O Output driver VREF output pin. FG signal input pin. (Connected to GND)
28 LASER O Laser ON/OFF control pin.
29 CONT1 I/O General-purpose input/output pin 1.
30 CONT2 I/O General-purpose input/output pin 2.
31 CONT3 I/O General-purpose input/output pin 3.
32 CONT4 I/O General-purpose input/output pin 4.
33 CONT5 I/O General-purpose input/output pin 5. (Not used)
34 PCK O EFM data playback clock monitor pin. Average 4.3218MHz when the phase is locked. (Not used)
35 C2F — C2 flag output pin. (Not used)
36 VDD — Digital power supply pin.
37 DOUT O Digital out output pin. (EIAJ format). (Not used)
38 FSX O Output pin for the 7.35kHz synchronization signal divided from the crystal oscillator. (Not used)
– 22 –
Pin No. Pin Name I/O Description
39 EFLG O C1, C2 error correction monitor pin. (Not used)
40 TEST I Test input pin. (Connected to GND)
Emphasis pin. Which becomes an input pin after reset and can be controlled externally. This
41 EMPH I/O
becomes an emphasis monitor pin under control by command. (Not used)
42 MUTEL O L channel mute output pin. (Not used)
43 MUTER — R channel mute output pin. (Not used)
44 LVDD — L channel power supply pin.
45 LCHO I L channel output pin.
46 LVSS — L channel ground pin.
47 RVSS O R channel ground pin.
48 RCHO I R channel output pin.
49 RVDD O R channel power supply pin.
50 XVDD O Crystal oscillator power supply pin.
51 XIN I
Connections for a 16.9344MHz crystal oscillator pin.
52 XOUT O
53 XVSS I Crystal oscillator ground pin.
54 ASLRCK I L/R clock input pin. (Connected to GND)
55 ASDACK I Bit clock input pin. (Connected to GND)
56 ASDFIN — L/R channel data input pin. (Connected to GND)
57 LRSY — L/R clock output pin. (Not used)
58 DATACK O Bit clock output pin. (Not used)
59 DATA O L/R channel data output pin. (Not used)
60 16M O 16.9344MHz output pin. (Not used)
Subcode frame synchronization signal output pin. This signal falls when the subcode is in the
61 SFSY O
standby state. (Not used)
62 SBSY O Subcode clock synchronization signal output pin. (Not used)
63 PW O Subcode P, Q, R, S, T, U and W output pin. (Not used)
64 SBCK I Subcode readout clock input pin. (Connected to GND)
65 CE I Chip enable signal input pin.
66 CL I Data transfer clock input pin.
67 DI I Data input pin.
68 DO O Data output pin.
69 INT O Interruption signal output pin. (Not used)
70 WRQ O Interruption signal output pin.
71 RES I Reset input pin. This pin must be set low briefly after power is first applied.
72 DRF O Focus ON detect pin.
73 C2F — Microprocessor interface power supply.
74 VDD — Digital ground pin.
75 DOUT I/O General-purpose input/output pin 6. (Not used)
76 CONT7 I/O General-purpose input/output pin 7. (Not used)
Rough servo/phase control automatic switching monitor output pin.
77 V/P O
“H” for rough servo and “L” for phase servo. (Not used)
– 23 –
Pin No. Pin Name I/O Description
Synchronization signal detection output pin.
78 FSEQ O Outputs a high level when the synchronization signal detected from the EFM signal
and the internally generated synchronization signal agree. (Not used)
Defect pin. Which becomes an input pin after reset and can be controlled externally. This becomes
79 DEFECT I/O
the defect monitor pin under control by command. (Not used)
80 EFMO O EFM signal output pin. (Not used)
– 24 –
ADJUSTMENT <TUNER / DECK / FRONT>
< TUNER SECTION > < DECK SECTION >
1. Clock frequency Check 1. Tape Speed Adjustment (DECK 1)
Settings : • Test point : TP2 (CLK) Settings : • Test tape : TTA–100
Method : Set to AM 1710kHz and check that the test point is • Test point : TP5 (Lch), TP6 (Rch)
2160kHz ± 45Hz. • Adjustment location : SFR501
Method : Play back the test tape and adjust SFR501 so that the
2. AM VT Check frequency counter reads 3000Hz ± 8Hz (FWD) and
Settings : • Test point : TP1 (VT) ± 45Hz (REV) with respect to forward speed.
Method : Set to AM 1710kHz, 530kHz and check that the test
point is less than 8.5V (1710kHz) and more than 2. Head Azimuth Adjustment (DECK 1, DECK 2)
0.6V (530kHz). Settings : • Test tape : TTA–330
• Test point : TP5 (Lch), TP6 (Rch)
3. FM VT Adjustment • Adjustment location : Head azimuth
Settings : • Test point : TP1 (VT) adjustment screw
• Adjustment location : L907 Method : Play back (FWD) the 8kHz signal of the test tape
Method : Set to FM 108.0MHz and adjust L907 so that the test and adjust screw so that the output becomes maximum.
point is 7.0V ± 100mV. Next, perform on REV PLAY mode.
– 25 –
MECHANICAL EXPLODED VIEW 1 / 1
22 B
24
C
B
B
B
B B
3ZG-3
B
20 PWB,HLDR FFC
B
B
C
B
C
B
A 23
a
21
16
11 H
A FL 9
D G
19 E
B
PWB,HLDR WIRE
C PWB
10 E
PWB
b 17
B 18
B
B ZZM-2 B
B
HT-SINK,TR LOW
C
6
7
F
B B
4 14
B B
b
5
12
15 a
3 13
C
B
1
2 8
3 25
– 26 –
MECHANICAL PARTS LIST 1 / 1
6 8A-NEC-031-010 WINDOW,DISP LH
7 87-B00-002-010 BADGE,AIWA 30 ABS SIL
8 86-NFZ-231-010 DMPR,70
9 8A-NEC-201-110 HLDR,PT
10 8A-NEC-001-110 CABI,FR
11 8A-NEC-008-010 KEY,POWER
! 12 87-A80-157-010 AC CORD ASSY,E BLK CC
13 8A-NEC-014-010 PANEL,RIGHT
14 8A-NEC-010-010 KEY,CASS 1
15 8A-NEC-011-110 KEY,CASS 2
21 8A-NEC-204-010 HLDR,CD R
22 8A-NEC-015-010 PANEL,TOP
23 8A-NEC-013-010 PANEL,LEFT
24 8A-NEC-024-210 CABI,REAR LHSC
25 8A-NEC-205-010 CABI,BOTTOM
– 27 –
TAPE MECHANISM EXPLODED VIEW 1 / 1
54 TERMINAL,LB1 A
4 22
14 TERMINAL,LB1 A
55
15
21 23 22
3 28 20
13
19 21 23
6 27
5 20
2 18 14
b 54
29
17 25 15
1 6
13 5 a
55 31
59 24 26
19
16
28
18 59
61
17 30
B 16
53 47 29
46 38 27
25
45 33 26
37 24
44
43 34
b
1
12 51
a
11 40 53
12 32
33
52 34
10 4
51
3 11 47
1
9 36
39 37
2 50 46 35
8
45
1 10 56
7
44
57 9 49
8 48 43
58
7 40 38
41
42
57
60
58
39
– 28 –
TAPE MECHANISM PARTS LIST 1 / 1
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
1 8Z-ZM1-254-310 SPR-C,REEL R 36 8Z-ZM1-220-110 LEVER,REC SENSOR
2 8Z-ZM1-225-110 GEAR,REEL R 37 8Z-ZM1-249-210 SPR-T,FR
3 8Z-ZM1-253-210 SPR-C,AUTO SENSOR 38 8Z-ZM1-242-310 SPR-T,FF/REW
4 8Z-ZM1-217-110 LEVER,AUTO SENSOR 39 8Z-ZM3-244-110 GEAR,CAM TD20
5 8Z-ZM1-212-210 LEVER,T-UP 40 8Z-ZM1-232-010 GEAR,IDL FF/REW
– 29 –
CD MECHANISM EXPLODED VIEW 1 / 2
F CUSH-G,
C MAIN
F
13
CUSH-G,
14 MAIN
a
3ZG-2 E3
15 b
11
5
10
7 E
8
4
B
6
D
a
12
A
MOT
PWB
b 1
– 30 –
CD MECHANISM PARTS LIST 1 / 2
6 83-ZG3-207-619 GEAR,TRAY
7 83-ZG3-204-21M GEAR,C
8 83-ZG3-205-019 GEAR,D
9 83-ZG3-211-01K PLATE,DISC
10 83-ZG3-220-21M GEAR,PULLEY 2
11 83-ZG3-214-019 BELT,L
12 83-ZG3-229-51K TRAY,CD 2
13 83-ZG3-210-119 HLDR,CHUCK
14 83-ZG3-604-010 RING,MAG 2
15 83-ZG3-212-019 CAP,DISC
A 87-067-945-119 VFT2+3-12(F10)
B 87-251-071-410 U+2.6-4
C 83-ZG3-235-010 VFT2+2.6-8
D 87-352-075-219 VT2+2.6-10
E 83-ZG3-217-019 S-SCREW,GEAR D
– 31 –
CD MECHANISM PARTS LIST 2 / 2
3
1
A
6 M2
SW1
5
PWB
6 83-ZG2-253-010 SHAFT,SLIDE 5
A 87-261-032-210 V+2-3
– 32 –
GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE)
Type.1 Type.4
Insert a flat-bladed screwdriver into the position indicated by the TOOLS
arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer
unit and then remove the speaker units.
2 (() flat head screwdriver
3 Cut chisel
1 2 3
Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counter-
clockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise Fig-1 Fig-2
direction until "click" sound comes out.
Fig-3
– 33 –
SPEAKER PARTS LIST (SX-NSZ2) <YLSL, YLSC>
– 34 –
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
9620450 0251431 Printed in Singapore