Professional Documents
Culture Documents
Lab 3 Meen211101049
Lab 3 Meen211101049
Lab 3 Meen211101049
meen211101049
Table of Contents
1 Objective: ................................................................................................................................ 16
2 Problem statement: ................................................................................................................. 16
3 Introduction to static Structural Analysis System: ..................................................................... 16
4 Procedure: ............................................................................................................................... 16
5 Input Design Data:.................................................................................................................... 17
6 Simply Supported Beam Analysis: ............................................................................................. 17
7 Engineering Data: ..................................................................................................................... 17
8 Geometry: ............................................................................................................................... 18
9 Mesh: ...................................................................................................................................... 19
10 Load: .................................................................................................................................... 19
11 Analysis Setting: ................................................................................................................... 19
12 Results: ................................................................................................................................ 19
13 Plot Result: ........................................................................................................................... 20
13.1 Plot Deformation: ............................................................................................................. 20
13.2 Plot Stress: ....................................................................................................................... 20 14
Discussion: ........................................................................................................................... 21
Page | 15
Reg no. meen211101049
List of figures
Figure 1schematic object ......................................................................................................... 18
Figure 2 Geometry Parts with all Necessary Information....................................................... 19
Figure 3mesh reqirement table ................................................................................................. 20
Figure 4: Static Structural with Equivalent Stresses Values .................................................... 21
Page | 16
Reg no. meen211101049
A Static structural analysis can be either linear or nonlinear. All types of nonlinearities are
allowed large deformation, plasticity, stress stiffening, contact element, hyper elasticity and so
on. Detail of how to handle nonlinearities are described in Nonlinear Controls. Note that
available nonlinearities can differ from one solver to another.
4 Procedure:
The procedure steps we taken shown below:
Open Static Structure Analysis from left toolbox of Analysis Systems
Then double click on engineering data to add a required material i.e. mild steel
Now again in workbench, open geometry and draw according to given data
Page | 17
Reg no. meen211101049
Now mesh the model and apply boundary conditions. Then save the project. Now
click on solution and select the stress, deformation, then click to solve.
It will show the ANSYS Analysis of stress and deformation in geometry window. The
minimum and maximum values will be shown on side with colors.
In case of Center load applied on the body we select the geometry and select the face
edge and take offset command from skitch and take the canter line on the body.
Then we select the face split option and select the surface edge and generate it.
Then go the model and select the force at the center the body and solve it.
Then we just check the value of deformation and stresses as above.
Save the images of all analysis and save the project report.
7 Engineering Data
Page | 18
Reg no. meen211101049
In the first, Select the material of your structure that is structural steel in that case. Then add
data that is about the Young`s modulus of material, poisson ratio etc. that is necessary to add.
8 Geometry:
After selecting the engineering data close it and select geometry from the project schematics.
Draw the geometry that is require with specific dimensions and saved it in system.
Mesh:
Page | 19
Reg no. meen211101049
After creating geometry select model from project schematic ANSYS simulation file will open
with geometry that has made before it. Then apply mesh on the structure according to
requirements.
9 Load:
After meshing then apply load that has to apply structure in particular area or face and apply
the boundary conditions and see the results.
10 Analysis Setting:
After applying the load and boundary conditions change the analysis setting according to
requirement or for more refine solution
11 Results:
As you solve the structure software show all the possible stresses, deformation and strains that
may occur in the structure for that particular load.
Page | 20
Reg no. meen211101049
12 Plot Result:
The result that has made by ANSYS on simply Supported beam with UDL.
Page | 21
Reg no. meen211101049
13 Discussion:
In this report the value of deflection calculated experimentally through ANSYS software. The
value of deflection is 2.3378mm with center load . Furthermore, I also calculated the value of
stresses experimentally through Using ANSYS and get the value of Stresses. The maximum to
minimum values which is 115.48 MPa and 1.1432 MPa respectively, with center load.
Page | 22