Professional Documents
Culture Documents
Q Mum-Noida Motor Mep August 2021
Q Mum-Noida Motor Mep August 2021
02/08/2021
Internal: GL Meena
Function 4 Motor
Type of ship
Type of engine
What are different cards? Explain light spring card, draw card?
Function 6 MEP
what type of bige valve you had?
How you mearure rudder drop in rotary vane type steering gear?
Got Motor
Mep repeat
02/08/2021
Internal: GL meena
Duration: >1 hr
Function 4 and 6
Type of Ship
Type of engine
Type of governor. Which type of governor in ME and AE. Working of both. How it
mantains constant speed?( I had no idea)
Windlass brake testing(iski g me ghus gaya). How does the testing equipment look like?
How it functions?
A pipe having 10 bends with varying diameter has hole. How to fabricate same pipe?
Leekage in shell and tube type heat exchanger and lots of cross question.
Engine type
Mep
02/08/2021
Motor&MEP
Vane type steering gear system & its rudder drop calculation
Refrigeration unloader working
Purifier seal ring damaging continuesly even after replacing with new, Reasons?
Fire fighting systems onboard? Weekly, monthly, yearly maintenance portable fire
extinguisher?
4/08/21
NOIDA
4b & 6
Both passed.
COC
04/08/2021
NOIDA
Manjhi Sir
PR KAPOOR SIR
Scavenging types
REPEAT
04/08/2021
NOIDA
Int: Subbarao
Function 4 and 6
Passport checked
Function 4
Which flywheel is bigger 2stroke or 4stroke
Telescopic Pipe
Function 6
Oxy-Acetylene safeties
Welding Defects
04/07/2021
Type of engine
Azimuth working
Cankcase inspection
04/08/2021
Noida
Kamat sir
meena sir
Type of engine
Azimuth working
Cankcase inspection
Compressor working
05/08/21
Meena sir
Kamath sir
Ship u sail
Mc and mc-c
Piston clearance and cross question
Surging
Lubrication on tc
Bearings in tc
Scavenge fire
Tappet clearance
Cylinder lubrication
05/08/2021
4b & 6
Manjhi sir
Vishwanathan Iyer
Ship type(offshore)
Engine type
Filters were there for L.O and F.O, tell me which of the filter was smaller micron filter.
Turbocharger
Shaft generator
MEP
Colour of tube
What & how many things u can do with a ball pin hammer.
Chloride ppm
Motor pass
Mep repeat
05/08/2021
kamath sir
MEP
3. principal of FWG? vaccum is not developing what are the reasons, ejector p/p is
working fine?
5. id JCW is not there how will you generate water? (ans. fabricated a steem line)
7. why p- alkinity, and chloride test done and its effect and remedy?
10. centrifugal p/p working? NPSH? if discharged v/v is closed what will be its effect? how
to find out if impeller and shaft are ready to be used again?
11. why we take tappet clearance ? piston comes to TDC twice in a power stroke when will
u take tappet?
13.Revesing of engine
06/08/2021
f 4b & 6
subbarao sir
nijhawan sir
Date-7/8/21
Noida
Internal- Meena
MOTOR/MEP
Engine specifications
mc-c advantage,
05-08-2021
Internal -manji
Engine type
Generator type
Turbocharger lubrication.
Internal meena
Motor
Motor,mep
Ext-anil
5. Detection of leaky starting air valve during engine running and at stop condition
8. How to detect shell type heat exchanger tube side leakage, and the remedy action for
that.
9- Aug 2021
Ext-Anil bhat
Int- Meena
Types of lubriation
Difference between thick shell and thin shell
Refrigerant properties
Pipe fabrication
Motor pass
MEP repeat
09/08/2021
(50- 60mins )
Motor
Propulsion Motor Safety , Each motor power and how it's started.
Type of Engine
Engine Specifications
If V type of Engine, you have one connecting rod or two. How con- rod is driving both
units.
If you overhauled cylinder head and brought it to workshop , how will you identify which
is suction and exhaust valve.
In air compressor , what is the difference between suction and exhaust valve.
Tell me about construction of fuel pump and all parts of fuel pump
Is there any delivery valve present in fuel pump, purpose of the delivery valve .
How meat room temperature is maintained at -15°C while your dairy room temperature is
+4°C, by the same refrigerant.
MEP
How would you change a gasket in the flange of a SW pipe if the gasket has worn out .
In shell and tube type heat exchanger , how will you come to know if heat exchanger is
fouled.
If ballast pump has stopped taking suction or if the tank level has dropped, how will you
come to know and what will be your actions.
In a centrifugal pump , if we use gland packing , how we prevent shaft from erosion .
In purifier , at one time my oil is coming out with water and another time water is coming
out with oil , what is the problem ?
If the grade of oil being used is same , why would you encounter the above problem ?
Cleared All
*1.How would you change a gasket in the flange of a SW pipe if the gasket has worn
out .*
1. I told him that first I will check the thickness of the gasket material, type of gasket
material.
And then I will take the old gasket and draw it over a new gasket material .
And prepare the flange by cleaning it properly and then fit the new gasket .
*2.In shell and tube type heat exchanger , how will you come to know if heat
exchanger is fouled.*
And secondly I will check the temperature of SW it will drop and the JW OR FW
outlet temperature would rise , more than normal as it won't be cooled properly .
*3.In a centrifugal pump , if we use gland packing , how we prevent shaft from
erosion .*
3. I just told him we put a sleeve in the way of packing and he was happy with this
answer.
*4.In purifier , at one time my oil is coming out with water and another time water is
coming out with oil , what is the problem ? If the grade of oil being used is same ,
why would you encounter the above problem ?*
4. I told him first of all there might be a problem with the gravity disc, if the size is
small then water will carryover with oil And if the disc is large the oil will carryover to
water outlet .
And now if the gravity disc is same and grade of oil is also same, then there is the
problem with temperature and density of the fluid.
We are not heating the fluid properly so proper interface is not forming as per the
gravity disc used .
*5. what could be the reason for water coming in gear box side of purifier.*
5. I said water can enter from the bowl side when the O-RING leaks. Due to clearance
around vertical shaft...
9/aug/2021
noida mmd
int-meena
fun-4b and 6
why it is hard to weld c.i , why u need to heat c.i before welding.
what could be the reason for water coming in gear box side of purifier.
cylinder oil non flow alarm comes what will you do u are on watch.
16/08/2021
MUMBAI
Ext-Anil Bhat
Fn4b
*What is super long stroke, what is the difference between MC and MC-C?
*What type of drive is used for camshaft in your main engine, what are the advantages of
a chain drive over a gear drive?
*Local manouvering and what alarms can't be bypassed during crash manouvering
*Why do we need an intermediate shaft in-between thrust shaft and tailshaft?
Fn6
How will you repair a main l.o. shell & tube cooler mid operation?
Difference between thick and thin shell bearings and where they are used
How will you repair damaged economizer tubes mid sea?(exact words)
How will you fabricate a new pipe if the previous one has been damaged beyond repair?
During mid decarb sudden notice from bridge to prepare engine. what are your actions?
16/8/2021
Mep
Stp maintenance
17/08/2021
MUMBAI
Ext-Anukul hoon
Fn6 MEP
What all machineries u have done overhaul?
What test you do on Fuel injectors? Tell me specific values like at what bar and all.
What are LO test tell me what all you have done personally and steps?
How will you start stp after overhaul and what are routine tests on it?
Meena
anukul Hoon
Date 17/08/21
Motor 4b
Engine specification
Sfoc
Cpp working
Shaft generator
repeat
17 Aug 2021
mumbai
Storm valve
Droop of governor
Progressive pump?
Stp
passed
17/08/2021
MUMBAI
MEENA SIR
4B
Nomenclature
Storm valve
Got coc
17/08/2021
Meena sir
Anukul hoon
Fucntion 4b
me type
nomenclature
schedule 40 80
piston clearance except ring clearance and side clearance(pata nahi kya sunna tha)( don't
know..bakchodi kiya isme)
fwg maintenance
pumps alignment
Also @Akshat DCI@Boiler thanks bhai...for ur prompt replies to evry doubt ...
18/08/2021
2) purifier not pipicking rpm (bowl closing water and friction pad)
18/08/2021
Function motor
Few more
Pass
18/08/2021
MUMBAI
MEENA SIR
PRAVEEN SABA
MEP
Air compressors trips and alarms. How No air flow trip measures
18/08/2021
Mumbai
Meena Sir
Praveen saba
Mep
Compensating ring
Cavitation
Got safety
18/08/2021
4b
Stresses on crankshaft
Sfoc
Me decarb
Compressor safeties
Bumping clearance
Steam traps
Specific gravity
Boiler mountings
Pass
Function 4b 6
Mumbai MMD
Aashish Wankhede
Sanjib SIR
Chocks
4s and 2 s cycles
System LO differece of 4s 2s
Cleared both
18/08/2021
INTERNAL :Ashish Wankhede
Type of ship
Number of Functions
Function 6 MEP
* engine room crane checks one day before major unit overhaul
( Here he wants to know which are all valves you will close and which pump you will start
for emergency bilge suction)
Thats all
COC
Fn 6 mep
* engine room crane checks one day before major unit overhaul
Hook condition
Gears condition
Electrical supply
* Engine room Flooding ....your actions
( Here he wants to know which are all valves you will close and which pump you will start
for emergency bilge suction)
Shut sea suction valve, open emergency bilge suction valve, start respective ballast pump
1. Isolate the system, close respective valves and takeout the pipe
3. Now we need make sure that angle between flange and pipe should be same as old
one. For that we have to make a jib.
3. Take angle plate and flat bar and take two flanges of same size.
4. Fit those flanges to old pipe flange with nuts and bolts.
5. Now use angle plate and flat bar and weld it to those flanges so that they don't not
move.
6. Now take out nuts and bolts and remove old defective pipe.
Now jig is ready which has same length and angle dimensions as that of old one.
7. Now bring two new similar flanges and fix it with flange of the jig with nuts and bolts.
8. Bring new pipe of same dimension and put between new flanges and make a tack weld
on both sides
Now we have to test the fitting by using it to the actual location...if all ok then...
9. Now to complete the welding of flange ... first put that pipe in the jig again and tighten
it with nut and bolts.
10. Complete the welding of flange to the pipe. (If we don't put it in jig then while welding
flange angle may get change due to thermal expansion .... then it won't fit in actual
location)
11. Allow it to cool down then remove from jig and Your pipe is ready with exact replica as
that of old one.
18/08/2021
Mumbai
Manjhi sir
Sanjib sir
Function 6
Greasing of centrifugal pump which grese you used company and greese specifications
Jacket water chemicals what all are types of chemicals and why specially that chemical
He said you only have therotica knowledge need to have practical experience..
I messed up there...but later i told i will shut sea suction and open emergency bilge
suction valve and start ballast pump
Problem in atmospheric condenser...he asked then what will you do...i said i dont know
Sanjib
Wankhede
Safety:
-Keel types
-Types of floors
- block coefficient
Annex 6 regulations
Rest forgot
Mep:
Rest forgot
Passed
accepted answer
18/08/2021
2nd Attempt
Mep
1) suppose ur 2nd eng. Tells u that we have to discharge from BHT, so tell me exact what
procedure u carry out....
8) MAC is not building pressure and also the current drawn is very less what is the
reason?? And how will u rectify it??
1) Normal operation but imp thing tell him about how to operate 3 way valve
2) I told him 1st accept alarm then go to the platform i would adjust the feed to the evap...
Also told him that this will happen if problm with vacuum breaker he said ok...
3) I told him ki jacket cooling water inlet and outlet will isolate.... And exp tank valve to
isolate. And also air starting valve....
This 8th I had solenoid valve so check whether its getting supply or no and rectify it i told
him he was happy18/08/2021
Wankhede sir
sanjib sir
Mep
Lube test
rest forgot
pass
18/08/2021
Mumbai
Internal : Manjhi
External : Kamath
Function 6 MROL
Purifier overhauling
Internal: Wankhede
Ext:sanjeeb
Motor/4b
Hydrodynamic lubrication ...then slowly drifted to all other types of lubrication ..and cross
head .
How does air starting cam disengage in A/E ?..i couldn't answer .
Sanjeeb is very polite and kind hearted examiner ..tries yo guide you to right answers
...gives feed back!
Biggest Thanku to the whole HATC team !!..and every brother here who helped clear my
doubts ...i will definitely be back for class 2!
Motor
From where you did presea
2s piston construction
Scuffing
Generator starting air system ( i said electric motor), then how this motor engaged and
disengaged (no idea)
Result - COC
18/08/202
mumbai
SANJEEB SIR
WANKHEDE SIR
Mep motor
I told him regarding my fwg that was 2 stage and plate type.
He wanted to know how to find crack in plate after you take out all the plates .
I told him by visual inspection but again he asked what will you check in visual inspection
for crack and how... I wasn't able to answer
Ques: How to replace new bearing in centrifugal pump and how to?
For bearing i told him to clean the shaft, check for any scoring or irregularities and then
heat the bearing by lamp.
Then he asked me will you directly heat the bearng by flame lamp i told him that i will
heat it in oil not directly.
Plate u have to put torch light from one side to other and u can see cracked plates will
show light on other side.
18/08/2021
Mumbai Mmd
Int:- Manjhi
Ext:- Kamath
*Function 6: MEP
What is superheat
Electrical - Pass
18/08/2021
INT:Purna Majhi
EXT: Kamath
Motor
Engine type
& Specifications,
Turbocharger maker,
Turbocharger type,
Causes if phosphate is high & hydroxide is high & hydroxide & bicarbonate level is high,
In FWG starting time not creating vaccum(pump working fine)what the reason,
Tappet clearance
2s & 4s cycle,
LO test,
Ref cycle,
Cavitation,
Got MEP
23/8/2021
Motor
Octane no
Creep
Fractional distillation
Bed plate location
Boiler mountings
Result coc
23/08/2021
Mumbai
Meena sir
Sanjib sir
Mep
crankcase inspection of AE
Dp test
rest forgot
COC
23/08/2021
Mumbai
Meena sir
Sanjib sir
MEP
*Economiser funnel smoke coming ur action (Never slow down Engine ...bcz of this I got
failed)
*Generator rotate water coming ur action Water coming out from indicator cock ..
Date:- 23/08/2021
Mumbai mmd
Internal- meena
External- sanjib
*Stop the pump of which one shows low pressure, that pump filter to clean
5.plate type cooler overhaul- said which was in apsingh mep book
Oil side cleaning- use carbon remover ( carbon tetra chloride solution)
Mumbai
24/08/2021
fn 6
- Decarb of AE.
- Steam drum inspection of boiler. process of depressurising the boiler and how to safely
open the manhole doors.
Result – Pass
• Preparation of ME.
- Look at the MOP and see all the parameters are okay and there are no alarms on the
panel.
- Start Jacket pre-heat pump if required, and start the LO pump if it's not running.
- Open the Indicator cocks as you go down and press up the air bottles.
- Start turning gear and observe the amperage. Ask the motorman above to look for any
water coming out from indicators cocks.
- I was going to say to drain the bottles and check the control air but then he moved on to
next question.
I said, I will check the condition of lube oil. It's color, smell and by pressing up between
fingers.
- The connecting rod should be able to move slightly sideways on bottom end bearing.
- if we are cleaning it, I'll look for any metal particles/parts broken down in the crankcase
and look at the attached LO Pump strainer.
- First I explained the entire process of depressurizing the boiler, like drop the pressure,
open the vent and let the boiler cool down etc etc.
- then open the top manhole door first and then the botom mahole door.
- have heavy duty gloves and face shield and slacked then manhole door and tilt life from
one side while staying behind the mahole door and only when it is ensured that no gases
are coming out should you proceed to slacken it a bit more.
basically, he wanted to listen this thing only. what all PPEs would be required and how
would you avoid any danger.Mumbai
24/08/2021
motor
Majhi
Anil deswal
Diffuser construction
Why simulation?
Gleson
24/08/2021
Mumbai
Manji sir
24/8/2021
MMD Mumbai
Ex- Sanjib
Int-Meena
Fn- Motor(4b)
5) Refrigerant Properties
6) BDN derails
Result: COC
Thanks everyone specially Saheem Khan.
24/08/2021
Mumbai
Ext-anil Deswal
Fn 6
-Liner scuffing.
24/08/2021
Mumbai
Manhji sir
Very helping
MOTOR 4b
-Which ship
-Engine nomenclature
-LO test
What will u do if the friction pad is worn out and you don’t have spare
Motor pass
Thank you saheem bhai.. and Mayur for all the help.
24/08/2021
Mumbai
Majhi sir
Anil deswal
MEP
Pass
I told him the difference is the way that operate. Relief valve is open gradually according
the pressure rise..
But safety valve open rapidly it have only 2 position fully open or fully closed
I told this much then he asked any other .. i told this much only I know
24/08/2021
Mumbai
Manjhi sir
Function 4b
Type of engine
Crankpin ovality
Result COC
24/08/2021
Mumbai
Subbarao sir
Kamath sir
Function -6
Mep -MROL
type of ship
Nomenclature
Ae decarb full all gudgeon pin lubrication and too much xx cross question
Ae inspection
Complete overhauling of purifier (from starting to end from where it comes n xx question)
What is reamer
What is creep
Decider
Result - Pass
24/08/21
where is bursting disc provided in air compressor safety and role of bursting disc
all the cards (Power card, light spring) what they indicate
Liquid priming unit emergency fire pump just tell abt priming unit working procedure like
starting
What is flywheel
Rest forget
Butt clearance
MainEngine trips
Maine engine not starting reasons
Thanks to both int and ext especially who clear my doubts today
Mumbai
25/08/2021
Meena sir
Sanjib sir
Motor
Entablature
Types of t/c.
Hot corrosion
Cold corrosion
Result : pass
Coc
Int : meena
Ext: sanjib
25/08/2021
Mep
AE crankcase inspection
Result : pass
Coc
MEP
MEENA
SANJIB
1- if your 4eng fire alarm come what action will you take?
PASS
Int: meena
Ext : sanjib
25.08.2020
1. Lo test
2. Tc water washing
4. ER flooded action
5. Fwg salinity
25/08/2021
subbarao
Anil deswal
4b
Thrust block
Concentric spring
OMD
Result-PASS
Int-manji sir
Ext-anil bhatt
Motor
1) type of ship
6) chain ans gear drive.. Advantage and disadvantaged and lot of cross question.
Result-PASS
COC
Internal : manji sir
Crankshaft type
Detuner function
Dampers working
Locking arrangements
Many more
Got coc
Int:meena
Ext:sanjib
25.08.2020
4b
crankcase explosion
Lo test
Result PASS
COC
25Aug
Meena Sir
Sanjib Sir
Motor:
- Type of ship
-Engine specifications
-ME Turbocharger construction, all components, blower side, turbine side, bearings, etc
-Turbocharger lubrication
-Full lubrication
MEP:
-Refer LO charging
- Plate type cooler cleaning process, how to find the leak, boxing back process. (Don't
forget to mention we'll measure the width before opening and compare it after boxing
back)
-Incinerator full
Thank you so much HATC and the one and only Saheem Bhai and all those who've
helped me
THANX TO THE WISE MAN
ACCEPTED ANSWER
1. In the normal running condition, First Try to Open and close the cock may be due any
carbon deposit it had not closed properly.. If still leak start the standby generator and
stopping the running generator and change the indicator cock. If engine can't be stopped,
put the cap on the indicator cock and tighten it for the time being till the time engine can
be stopped for changeover.
-Seal pot at the bottom will start leaking and water will enter the engineroom
Actions: stop the engine, let the egb to cool down, open top manhole door then bottom
manhole door, proper ventilation, go inside the egb with the torch, keep the water on,
tube leaking will start pouring water, mark the tube and plug it with the soft iron plugs,
also fill the tube with some refractory material to keep the tube sturdy.
25/08/2021
Mep
Anil bhatt
Manjhi
Fn6
Creep
Fn 3- pass
6 – repeat
26/08/2021
MUMBAI
MEENA SIR
KAMATH SIR
MEP
Tappet clearance,why,how,
Purifier vibration
Coc
26/08/2021
Mumbai
Int meena kumar
MOTOR MEP
Type of engine
Differenece in me and mc
Advantages of me over mc
Liner calibration
Piston checks
Alpha lubricator
Turbocharger bearings
Turbocharger lubrication
Purifier working
Assembling of purifier
Oxygen scavengers
Int
Communicate with bridge and tell the reading on the gyro repeater in the steering gear
room, put into local mode and by using lever on the torque motor we will control the
swash plate angle ...pump disharge pr is changed and rudder angle is achieved
It is a hollow tube in which tail shaft is going.it seals with lipseal which is holded by garter
spring.4 seal in the aft and 2 seal in the fwd.lip seal is fitted to chrome liner which is
rotating with shaft and protect tail shaft from erosion
Wait until the condenser inlet and outlet temp becomes equal...connect the purge bottle
on the condenser ..purge until the compound gauge(which shows pr and temp) temp and
condenser temp becomes equal....
260/08/2021
MEP
Int.RK Gupta
3. A/E L.O tests done onboard the ship. Tell me what is viscosity test,how you do it?
(Wanted to how you'll be exactly able to make out if the current oil is good to use or
not.Told him everything, wanted to listen something specific,idk.)
R.K Gupta, genuinely listens to what you have to say. Doesn't stops if you want to say
more. Old fellow, patient guy.
Aashish sir's video was off but he asked the internal. He said PASS 3 times 🥲
COC 🥲
@Saheem khan thank you soo much, also everyone that has helped and everyone
who keeps helping others.
26/08/21
-Motor
Which Ship
Engine
Sulphur content
Scrubber
Mep
-Compressor safety
Flame failure
-checks in hydrophore
-charging of refrigerants
26/08/2021
Mumbai
Internal - Ashish
External- RK Gupta
-Will dia will be equal from top to bottom of the cylinder ? ( Got confused)
-Annealing.
- Boiler water test, for what reason phosphate test is carried on?
- NDT testing, Dye penetrant test , Magnetic particle testing where exactly carried out
specially .
Function: 4b
Ext: rk gupta
1.engine specification
6.power card
Coc
27/08/2021
MUMBAI
MEENA SIR
PR KAPOOR
Mep
Fresh water producing less water
Mep pass
Electrical repeat
MUMBAI
27/08/2021
Anil bhat
Subbarao
Motor
Engine nomenclature
Mep
Tig
Mig
Bearing nomenclature
got motor
27/08/2021
Mumbai
Ext Kapoor
Int Meena
Engine particulars
Dg particulars
Purifier Low rpm - keeps asking for more and more reasons
Coc🥲
Ext- pr kapoor
Int - Meena
Motor
--Type of ME
COC
1--Rt flex
electronic control in which E95 is panel in each unit and 20 is FCM20 Module inside panel
for controlling
2- piston cooling-
3- I said...I was having crosshead lub pump thus I explained whole lubrication system of
crosshead through articulate arm and then at last I said with pressure we could get to
know about lubrication
4- Take on respective load..., Open indicator cock for few Sec Nd close it, basically for
removing carbon particles if stuck and then with the respective equipment we can take
the the performance
5- I explained everything regarding indicator diag. And I explained all draw cards fully and
describes all other cards
Int: meena
Ext: kapoor
Mera tarbook aur passport nahi tha Kapoor sir bola kii agli baar exam dee. I requested sir
doo maine see din raat padha hai sir kuch tho poocho. Bolta hai aur yek maina pad phir
dee exam. Then meena sir started asking
Motor
6.How does it maintain pressure in rail? Pump keeps running, rail has to pressurise ?
( I told on rail, there is a rail pressure sensor and this signal is feed to the control system
and control system actuate perssure control valve fitted at the end of the rail which will
release extra pressure of oil the tank)
9. Types of piston rings in AE? And how scrapper ring works and what special arrangment
fitted on it?
10. How many fuel injectors in 1 unit? How they operate? ( Depending on load, at low
load 1 and at high load 3)
12. How many turbochargers onboard and lubrication of it? During blackout how
lubrication done?
Mep
Cleared motor.
Meena sir saved me.
Thanks to all
27/08/2021
MUMBAI
ALL 4 FUNCTION
Result - Function 3 left rest all given. Thank you Saheem bhai.
30/08/2021
Subbarao Sir
MEP
Pass
30/08/2021
Int- Subbarao
MOTOR
Anil Deswal was not able to connect the meeting so Subbarao start asking me.
1. Your ME is running normally and suddenly stopped. Reasons? After this asked me the
trips and safeties relating to the ME.
3. How to do scum blowdown? Tell me the condition and criteria for it.
4. Properties of fuel oil stored onboard. Tell me the value of flash point.
5. Type of the boilers. Confusing a lot saying tell the main one, the exhaust one and at the
end said I want to know the auxiliary one. Confused a lot.
6. Still Subbarao was asking me the FO properties. Wanted to know the values.
7. Anil asked about the fuel oil leak off alarm, posn, where it is going to.
9. Hunting gear mechanism. Got deep into it. Asked me to explain full about it like how
the signal is coming from bridge to rudder and all.
10. Working of hunting gear and to which it is connected to? What is the significance of
those it is connected to?
At the end Subbarao said you was not upto the mark and you need to study more.
Repeat.
30/03/2021
Ext :kapoor
Int : Meena
MOTOR MEP
What is vit
Engine rpm
Subbarao sir
Deswal sir
30 Aug 2021.
Motor MEP
1.Centrifugal pump discharge low. reasons?
Result - pass
PR Kapoor (30/08/21)
MEP
1) M.E nomenclature
4) Purifier RPM low, reasons (I told all related purifier, maybe he was expecting Low
voltage in motor, anyways he was satisfied)
Cleared Both.
But he kept asking me.. why not top half of bearings clearance.. I KEPT SAYING TOP IS
LOADED
He asked.. where will the load act when con rod moves 360°
I said it shares load all places but we take clearance always at bottom
30 aug 2021
Fun: 3 and 4
Motor
Gov droop
Gov hunting
Thick thin bearing then he went to some dry bearing something(dnt knw)
Kapoor sir will continue asking deep in same quetion till the point you dont able to ans
and then he will change the question.
At the end he asked, what do you think of your orals, rate yourself, i said avg. Then he said
which fn you want from this two
I said safety
Cleared safety
Motor repeat
30/08/2021
Mumbai
Meena sir
PR Kapoor sir
Motor
Type of engine
Type of turbocharger
Turbocharger lubrication
Structure of ENGINe
Types of chock
30/08/2021
Mumbai
Meena sir
Pr Kapoor sir
Motor
Type of engine
30/08/2021
MUMBAI
MEENA SIR
PR KAPOOR SIR
GOT MEP
31/08/2021
Motor
1. Type of Engine
4. Interlock on ME
5. Explain starting air line and safeties on it
8. Matching of turbocharger
9. VTG
MEP
2. How will you find out leaking tube on shell and tube condenser
31/08/2021
MUMABI
Int-Meena sir
Ext.bhatt sir
Motor/Mep
Type of ship/engine.
MEP pass
31/08/21
Ext vishwanathan
Motor
4. Injector maintenance
Mep
1. Purifier type
6. Compressor specification
Motor repeat
31/08/2021
MOTOR MEP
- M/E is battery/Air staring. Engine is not getting started, what could be the problems.
- Some cross questions about piston rings and liner, liner calliberation, etc.
- Centrifugal pump not developing sufficient pressure, what could be the problems.
- Hydrophore pump is getting cutin/cutout very frequently, what will you check and
actions.
Ext Vishwanath
Int Ashish
MOTOR MEP
1. ME Nomenclature
7. Bunker tank to settling tank transfer. What type of pump? Can't centrifugal pump be
used?
mumbai
Vishwanathan sir
A Wankhede sir
1. ME AE Nomenclature
5. AE all unit crankcase door leaking (small leakage), why what will you do?
Meena sir
accumulation test.
Working of gov.
Interlocs working
improved safety vv
explain
2s 4s governor diff.