Professional Documents
Culture Documents
Cpi®-4600-100 Compressor Oil
Cpi®-4600-100 Compressor Oil
Cpi®-4600-100 Compressor Oil
0
Revision Date: 16.12.2021
1.2 Relevant identified uses of the substance or mixture and uses advised against
Identified uses: Formulated Industrial Lubricant
Uses advised against: None identified.
Classified in accordance with CLP Regulation (EC) No 1272/2008, as retained and amended
in UK law.
Not classified
2.2 Label elements in accordance with CLP Regulation (EC) No 1272/2008, as retained and
amended in UK law.
Not applicable
3.2 Mixtures
Compiled in accordance with CLP Regulation (EC) No 1272/2008, as retained and amended in
UK law.
This material has no known hazards under applicable laws.
SDS_GB - CPI®-4600-100 1/13
See Section 15 for Regulation (EC) No. 1907/2006 REACH Article 59(1). Candidate List (Substances of Very High Concern
(SVHC))
Eye contact: Any material that contacts the eye should be washed out immediately
with water. If easy to do, remove contact lenses.
Skin Contact: Wash with soap and water. If skin irritation occurs, get medical
attention.
4.3 Indication of any immediate medical attention and special treatment needed
Hazards: No data available.
Unsuitable extinguishing Do not use water jet as an extinguisher, as this will spread the fire.
media:
5.2 Special hazards arising A solid stream of water will spread the burning material. Material creates a
from the substance or special hazard because it floats on water. See section 10 for additional
mixture: information. Water may cause splattering. Container may rupture on
heating.
6.1 Personal precautions, Personal Protective Equipment must be worn, see Personal Protection
protective equipment and Section for PPE recommendations. Ventilate area if spilled in confined
emergency procedures: space or other poorly ventilated areas.
6.2 Environmental Avoid release to the environment. Do not contaminate water sources or
Precautions: sewer. Environmental manager must be informed of all major spillages.
Prevent further leakage or spillage if safe to do so.
6.3 Methods and material for Dike far ahead of larger spill for later recovery and disposal. Pick up free
containment and cleaning liquid for recycle and/or disposal. Residual liquid can be absorbed on inert
up: material.
7.1 Precautions for safe Observe good industrial hygiene practices. Provide adequate ventilation.
handling: Wear appropriate personal protective equipment.
7.2 Conditions for safe Store away from incompatible materials. See section 10 for incompatible
storage, including any materials.
incompatibilities:
7.3 Specific end use(s): End uses are listed in an attached exposure scenario when one is required.
Eye/face protection: If contact is likely, safety glasses with side shields are recommended. Eye
protection should meet the standards set out in EN 166.
Skin protection
Hand Protection: Suitable gloves can be recommended by the glove supplier. Consult
clothing/glove manufacturer to determine appropriate type of glove for given
situation. Gloves should always be inspected before each use and
discarded if they show tears, pinholes, or signs of wear.
General: Because specific work environments and material handling practices vary,
safety procedures should be specific for each intended application. The
correct choice of protective gloves depends upon the chemicals being
handled, and the conditions of work and use. Most gloves provide
protection for only a limited time before they must be discarded and
replaced (even the best chemically resistant gloves will break down after
repeated chemical exposures). Gloves should be chosen in consultation
with the supplier / manufacturer and taking account of a full assessment of
the working conditions. For typical use and handling of chemical
substances, gloves should meet the standards set out in EN 374. For
applications involving mechanical risks with potential for abrasion or
puncture, the standards set out in EN 388 should be considered. For tasks
involving thermal hazards, the standards set out in EN 407 should be
considered.
Break-through time: Breakthrough time data are generated by glove manufacturers under
laboratory test conditions and represent how long a glove can be expected
to provide effective permeation resistance. It is important when following
breakthrough time recommendations that actual workplace conditions are
taken into account. Always consult with your glove supplier for up-to-date
technical information on breakthrough times for the recommended glove
type.
For continuous contact, we suggest gloves with a minimum breakthrough
time of 240 minutes, or > 480 minutes if suitable gloves can be obtained. If
suitable gloves are not available to offer that level of protection, gloves with
shorter breakthrough times may be acceptable as long as appropriate glove
maintenance and replacement regimes are determined and adhered to.
For short-term, transient exposures and splash protection, gloves with
shorter breakthrough times may commonly be used. Therefore, appropriate
maintenance and replacement regimes must be determined and rigorously
followed.
Glove thickness: For general applications, we recommend gloves with a thickness typically
greater than 0.35 mm.
It is important to note that glove thickness is not the only predictor of glove
resistance to a specific chemical, as the permeation efficiency of the glove
will be dependent on the exact composition of the glove material.
Therefore, glove selection should also be based on consideration of the
task requirements and knowledge of breakthrough times.
Glove thickness may also vary depending on the glove manufacturer, the
glove type and the glove model. Therefore, the manufacturers’ technical
data should always be taken into account to ensure selection of the most
appropriate glove for the task.
Note: Depending on the activity being conducted, gloves of varying
thickness may be required for specific tasks. For example: Thinner gloves
(down to 0.1 mm or less) may be required where a high degree of manual
dexterity is needed. However, these gloves are only likely to give short
duration protection and would normally be just for single use applications,
before being disposed of. Thicker gloves (up to 3 mm or more) may be
required where there is a mechanical (as well as a chemical) risk i.e. where
there is abrasion or puncture potential.
Hygiene measures: Always observe good personal hygiene measures, such as washing after
handling the material and before eating, drinking, and/or smoking. Routinely
wash work clothing to remove contaminants. Discard contaminated
footwear that cannot be cleaned.
Particle characteristics
Particle Size: Not applicable
Particle Size Distribution: Not applicable
Specific surface area: Not applicable
Surface charge/Zeta potential: Not applicable
Assessment: Not applicable
Shape: Not applicable
Crystallinity: Not applicable
Surface treatment: Not applicable
Other information
Bulk density: 6.95 lb/gal (25 °C)
10.4 Conditions to avoid: Do not expose to excessive heat, ignition sources, or oxidizing materials.
10.5 Incompatible Materials: Strong oxidizing agents. Strong bases. Strong mineral acids and strong
oxidizing agents.
Dermal
Product: Not classified for acute toxicity based on available data.
Inhalation
Product: Not classified for acute toxicity based on available data.
Skin Corrosion/Irritation:
Product: Remarks: Prolonged or repeated skin contact as from clothing wet
with material may cause dermatitis. Symptoms may include
redness, edema, drying, and cracking of the skin. Prolonged or
repeated contact may cause irritation. Not classified as a primary
skin irritant.
Respiratory sensitization:
No data available
Skin sensitization:
No data available
No data available
Aspiration Hazard:
No data available
Chronic Effects
Carcinogenicity:
No data available
Reproductive toxicity:
No data available
Endocrine Disruption
Product: No data available.
12.1 Ecotoxicity
Fish
No data available
Aquatic Invertebrates
No data available
Sediment Toxicity
No data available
Toxicity to microorganisms
No data available
BOD/COD Ratio
No data available
12.4 Mobility:
No data available
ADR
Not regulated.
IMDG
Not regulated.
IATA
Not regulated.
14.7 Transport in bulk according to Annex II of MARPOL and the IBC Code
None known.
Shipping descriptions may vary based on mode of transport, quantities, temperature of the material, package size,
and/or origin and destination. It is the responsibility of the transporting organization to follow all applicable laws,
regulations and rules relating to the transportation of the material. For transportation, steps must be taken to
prevent load shifting or materials falling, and all relating legal statutes should be obeyed. Review classification
requirements before shipping materials at elevated temperatures.
15.1 Safety, health and environmental regulations/legislation specific for the substance or
mixture:
EU Regulations
EU. Regulation 1005/2009/EC on substances that deplete the ozone layer, Annex I,
Controlled Substances:
None present or none present in regulated quantities.
EU. Chemicals Subject to PIC Procedure: Regulation 649/2012/EU on export and import of
dangerous chemicals, as amended:
None present or none present in regulated quantities.
Regulation (EC) No. 1907/2006, REACH Annex XIV Substances subject to authorisation, as
amended:
None present or none present in regulated quantities.
Regulation (EC) No. 1907/2006 Annex XVII Substances subject to restriction on marketing
and use:
None present or none present in regulated quantities.
Directive 2004/37/EC on the protection of workers from the risks related to exposure to
carcinogens and mutagens at work.:
None present or none present in regulated quantities.
Directive 92/85/EEC: on the safety and health of pregnant workers and workers who have
recently given birth or are breast feeding.:
None present or none present in regulated quantities.
EU. Directive 2012/18/EU (SEVESO III) on major accident hazards involving dangerous
substances, Annex I:
EU. Regulation No. 166/2006 PRTR (Pollutant Release and Transfer Registry), Annex II:
Pollutants:
None present or none present in regulated quantities.
Directive 98/24/EC on the protection of workers from the risks related to chemical agents at
work:
None present or none present in regulated quantities.
Inventory Status
Australia (AIIC)
All components are in compliance with chemical notification requirements in Australia.
Canada (DSL/NDSL)
All substances contained in this product are in compliance with the Canadian Environmental
Protection Act and are present on the Domestic Substances List (DSL) or are exempt.
China (IECSC)
All components of this product are listed on the Inventory of Existing Chemical Substances in
China.
Japan (ENCS)
This product contains a substance that is not listed on the Japanese Existing and New Chemical
Substances (ENCS) list.
Korea (ECL)
All components are in compliance in Korea.
Philippines (PICCS)
All components are in compliance with the Philippines Toxic Substances and Hazardous and
Nuclear Wastes Control Act of 1990 (R.A. 6969).
Switzerland (SWISS)
All components are in compliance with the Environmentally Hazardous Substances Ordinance in
Switzerland.
Taiwan (TCSCA)
All components of this product are listed on the Taiwan inventory.
Turkey (KKDIK)
To obtain information on the KKDIK compliance status of this product, please e-mail
REACH@SDSInquiries.com.
The information that was used to confirm the compliance status of this product may deviate from the
chemical information shown in Section 3.
15.2 Chemical safety No Chemical Safety Assessment has been carried out.
assessment:
Key literature references and Internal company data and other publically available resources.
sources for data:
Other information:
Disclaimer: As the conditions or methods of use are beyond our control, we do not
assume any responsibility and expressly disclaim any liability for any use of
this product. Information contained herein is believed to be true and accurate
but all statements or suggestions are made without warranty, expressed or
implied, regarding accuracy of the information, the hazards connected with
the use of the material or the results to be obtained from the use thereof.
Compliance with all applicable federal, state, and local regulations remains
the responsibility of the user.
Reference to Regulation (EC) No. 1907/2006 (EU REACh), including but not
limited to EU REACh registration numbers is provided for informational
purposes only. UK REACH (EU Exit Regulation as amended) data and
information will be provided as it becomes available.