Professional Documents
Culture Documents
Perete Barne Stejar Sipcuit Lutuit Si Izomineral 120 Cu Lut Peste
Perete Barne Stejar Sipcuit Lutuit Si Izomineral 120 Cu Lut Peste
lut peste
Thermal protection Moisture proofing Heat protection
Condensate: 2,03 kg/m² Temperature amplitude damping: 57
U = 0,30 W/(m²K) Dries 91 days phase shift: 16,8 h
Thermal capacity inside: 71 kJ/m²K
Interior insulation: No requirement*
outside
110 5
60 4
320
www.ubakus.de
20 3
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
120 2
10 1
inside
1 Clay plaster (10 mm) 3 Clay plaster (20 mm) 5 Eiche (110 mm)
2 Multipor (120 mm) 4 conluto Lehm-Unterputz (60 mm)
conluto Lehm-Unterputz
Eiche Equivalent
insulation thickness
Multipor (DAA) (WLS 047)
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 400 420 440 mm
8 95 u 5 au ,1
41
0
O u ba =0,2 ub ,15 =0
=0 U
DI
N
u tzV Ne U e
6 N au 0,2 U us
ch 14 V1 eub U= .
s 40 a
es EV au ivh
m En
E
En 20 N nMV aßn r-H KfW ss
är ite au Pa
W 20 ESa elm 5 3-L eub
G z 5
GE Ein KfW N
W
Kf bau
u
Ne
*Vergleich mit dem Höchstwert gemäß GEG 2020 für erstmaligen Einbau, Ersatz oder Erneuerung von Innenraumseitigen Dämmschichten (keine Page 1
Anforderung).
All statements without guarantee
Perete barne stejar sipcuit lutuit si izomineral 120 cu lut peste, U=0,30 W/(m²K)
Temperature profile
Temperature profile
20 Temperature
1 2 3 4 5 Dew point
15 Condensate
1 Clay plaster (10 mm)
Temperature [°C]
10
2 Multipor (120 mm)
5 3 Clay plaster (20 mm)
4 conluto Lehm-Unterputz (60 mm)
0 5 Eiche (110 mm)
-5
-10
0 50 100 150 200 250 300 350
Inside 0°C [mm]
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
www.ubakus.de Outside
Temperature and dew-point temperature in the component. The dew-point indicates the temperature, at which water vapour
condensates. As long as the temperature of the component is everywhere above the dew-point temperature, no
condensation occurs. If the curves have contact, condensation occurs at the corresponding position.
Page 2
All statements without guarantee
Perete barne stejar sipcuit lutuit si izomineral 120 cu lut peste, U=0,30 W/(m²K)
Moisture proofing
For the calculation of the amount of condensation water, the component was exposed to the following constant climate for
90 days: inside: 20°C und 50% Humidity; outside: -5°C und 60% Humidity (Climate according to user input).
Interior heat transfer resistance Rsi (user input deviating from DIN 4108-3):0.13 m²K/W
Under these conditions, a total of 2,0 kg of condensation water per square meter is accumulated.This amount would require
91 days to dry in the summer (Drying season according to DIN 4108-3:2018-10). This is more than the 90 days permitted by
the DIN 4108-3, and it must be expected that the component does not dry out completely in the warm season!
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
Condensation areas
1 Condensate: 2 kg/m² Affected layers: Clay plaster, Multipor (DAA)
Humidity
The temperature of the inside surface is 19,0 °C leading to a relative humidity on the surface of 53%.Mould formation is not
expected under these conditions.
The following figure shows the relative humidity inside the component.
Page 3
All statements without guarantee
Perete barne stejar sipcuit lutuit si izomineral 120 cu lut peste, U=0,30 W/(m²K)
Heat protection
The following results are properties of the tested component alone and do not make any statement about the heat protection
of the entire room:
Temperature profile
This document has been generated by the U-value calculator on www.ubakus.de. If you are harmed by the free use of these contents, the service provider is only liable in case of
32
30 1 Clay plaster (10 mm)
Temperature [°C]
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
16
Phase shift* 16,8 h Heat storage capacity (whole component): 362 kJ/m²K
Amplitude attenuation ** 57,1 Thermal capacity of inner layers: 71 kJ/m²K
TAV *** 0,018
* The phase shift is the time in hours after which the temperature peak of the afternoon reaches the component interior.
** The amplitude attenuation describes the attenuation of the temperature wave when passing through the component. A value of 10
means that the temperature on the outside varies 10x stronger than on the inside, e.g. outside 15-35 °C, inside 24-26 °C.
*** The temperature amplitude ratio TAV is the reciprocal of the attenuation: TAV = 1 / amplitude attenuation
Note: The heat protection of a room is influenced by several factors, but essentially by the direct solar radiation through windows and the
total amount of heat storage capacity (including floor, interior walls and furniture). A single component usually has only a very small
influence on the heat protection of the room.
Page 4