Professional Documents
Culture Documents
Dsc60 (A) Plus Sir Zeah-0516a
Dsc60 (A) Plus Sir Zeah-0516a
(JP: ZEAV-0516C)
DSC-60Plus/-60APlus
Customer Name:
Department:
Operator Name:
Performed by:
Group/Department:
Special Notes
Shimadzu Corporation
-1-
ZEAH-0516A
(JP: ZEAV-0516C)
Installation Check Sheet
2 Utilities
a. Insulation Check the insulation Use a digital voltage meter
resistance between the AC line (or a multi-meter).
and chassis and between
heaters and the chassis (while
the main switch is turned on Each insulation resistance:
without connecting the power). 10M min
b. Power Check the voltage using a Both the voltage and the
supply digital voltage meter (or a capacity meet the
multi-meter). specifications.
Confirm the capacity with the (Stable with no variation)
customer. The required
capacity is 5A.
c. Ground Make sure that the earth line is The voltage between the
securely grounded. AC hotline and earth line:
Around 100V
d. Confirm that the installation The requirements are
Environmental environment meets the fulfilled.
conditions conditions described in the
Instruction Manual.
3 Basic functions
a. Control keys Ensure that the control keys Smooth operation
function properly.
-2-
ZEAH-0516A
(JP: ZEAV-0516C)
No Item Descriptions Criteria Confirmed Note
4 Performance
a. Baseline Without a sample and cells,
(1) Standard spec: (1) Within the range of
Raise the temperature to 50C to 600C:
600C at 20C/min Drift: 5 mw max.
(2) TAC spec with no cooling: Deviation from ideal line:
Raise the temperature to 1.2 mw max.
500C at 20C/min (2) Within the range of
(3) When TAC-60i or TAC-60L 50C to 500C:
is attached: Drift: 4.1 mw max.
Sampling interval: 1 s Deviation from ideal line: 1
mw max.
Temp. Target Hold
Rate Temp. (3) With TAC-60i, within
the range of -50C to
1 -99.9 -150 30
500C, Attach
2 20.0 500 1 With TAC-60L, within the data
3 -20.0 -130 1 range of -130C to 500C:
Drift: 6 mw max.
In the case of TAC-60L,
remove the cable connecting Deviation from ideal line:
the pump and FC-60A, and 2.2 mw max.
turn on the power of DSC.
Then, turn on the power of the
pump and supply liquid
nitrogen so that you can start
the temperature program.
After the completion of the
measurement, turn off the
power of the pump.
Set the baseline correction
coefficient to an optimum
value.
b. Noise (1) Standard spec and TAC (1) 3 W (p-p) max.
spec with no cooling: (2) When the temperature
Hold at 150C for 30 minutes. is increasing
Apply 100-point smoothing to (with TAC-60i, from -50C
the data to correct the blank to 500C,
baseline. with TAC-60L, from -130C
(2) When TAC-60i or TAC-60L to 500C):
Attach
is attached: 36 W (p-p) max.
data
Apply 100-point smoothing to When the temperature is
the data obtained from above decreasing
procedure (3) to correct the (with TAC-60i, from 500C
blank baseline. to -50C,
with TAC-60L, from 500C
to -130C):
60 W (p-p) max.
-3-
ZEAH-0516A
(JP: ZEAV-0516C)
c. Sensitivity Place indium (with a purity of Onset temperature:
99.99% or greater) on the 156.5 1.5C
right and an empty cell on the Attach
Calorific value:
left. data
Raise the temperature to -27 to -30 J/g
180C at 10C/min
d. Continuous After performing “teaching”, No abnormalities
operation perform continuous operation
(For 60A only) in the TEST sim mode for 3
hours using samples of No.1
to No. 24 with empty cells.
-4-