Professional Documents
Culture Documents
Service: Digital Laser MFP
Service: Digital Laser MFP
SERVICE
DIGITAL LASER MFP
MANUAL
CONTENTS
1. Precautions 2. Specications 3. Disassembly 4. Troubleshooting 5. Exploded Views and Parts List 6. Block Diagram 7. Connection Diagram
ELECTRONICS
This Service Manual is a property of Samsung Electronics Co.,Ltd. Any unauthorized use of Manual can be punished under applicable International and/or domestic law. Samsung Electronics Co.,Ltd. JULY 2003 Printed in Korea. VERSION NO. : 1.00 CODE : JC-0086A
This service manual is also provided on the web, the ITSELF system Samsung Electronics Co., Ltd. http://itself.sec.samsung.co.kr
2003. 07
Precautions
1. Precautions
Follow these safety, ESD, and servicing precautions to prevent personal injury and equipment damage.
6. Be careful that small parts such as screws do not get lost inside the printer. 7. When disassembling take note of the placement of small parts. Ensure all small parts are properly reassembled. 8. If is is necessary to turn the printer upside down protect the LSU window with clean paper so that no loose toner particles contaminate the glass.
Releasing Plastic Latches Many of parts are held in place with plastic latches. The latches break easily : release them carefully. To remove such parts, press the hook end of the latch away from the part to which it is latched.
1-1
Precautions
4. Use only a grounded tip soldering iron to solder or desolder ESDs. Use only an anti-static solder removal device. Some solder removal devices not classied as anti-static can generate electrical charges sufcient to damage ESDs. 5. Do not use Freon-propelled chemicals. When sprayed, these can generate electrical charges sufcient to damage ESDs.
2. Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, employ a commercially available wrist strap device, which should be removed for your personal safety reasons prior to applying power to the unit under test. 3. After removing an electrical assembly equipped with ESDs, place the assembly on a conductive surface, such as aluminum or copper foil, or conductive foam, to prevent electrostatic charge buildup in the vicinity of the assembly.
6. Do not remove a replacement ESD from its protective packaging until immediately before installing it. Most replacement ESDs are packaged with all leads shorted together by conductive foam, aluminum foil, or a comparable conductive material. 7. Immediately before removing the protective shorting material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 8. Maintain continuous electrical contact between the ESD and the assembly into which it will be installed, until completely plugged or soldered into the circuit.
9. Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as the brushing together of clothing fabric and lifting ones foot from a carpeted oor, can generate static electricity sufcient to damage an ESD.
1-2
Samsung Electronics
Precautions
3 Driver
Standard : "-" type, "+" type (M3 long, M3 short, M2 long, M2 short).
4 Tweezers
Standard : For general home use, small type.
2 Electronic Scales
Standard : Equipment to check the weight of consumables(toner cartridge) supplied by Samsung Electronics. (The scales should measure in grams.)
5 Cotton Swab
Standard : For general home use, for medical service.
6 Cleaning Equipments
Standard : An IPA(Isopropyl Alcohol)dry wipe tissue or a gentle neutral detergent and lint-free cloth.
Samsung Electronics
1-3
Specication
2. Specication
Specications are correct at the time of printing. Product specications are subject to change without notice. See below for product specications.
Samsung Electronics
2-1
Specication
Data coding(Compression) Modem speed Transmission Speed Effective Scanning Width Halftone Paper Capacity(Input) FAX Mode Memory
2-2
Samsung Electronics
Specication
Optical Resolution (H x V) Multi Copy Maximum Original Size Maximum Page Size Paper Type Selection Zoom Range
NOTE : (1) Speed claims based on the test chart : A4 size. SDMP : Single Document Multiple Printout MDSP : Multiple Document Single Printout
Samsung Electronics
2-3
Specication
2-7 Consumables
Item Type Life Toner Cartridge Drum Cartridge Description Separate type (Toner Cartridge / Drum Cartridge) 6,000 sheets ( 5% coverage pattern, simplex normal mode ) 15,000 sheets (simplex normal mode )
2-4
Samsung Electronics
When you disassemble and reassemble components, you must use extreme caution. The close proximity of cables to moving parts makes proper routing a must. If components are removed, any cables disturbed by the procedure must be restored as close as possible to their original positions. Before removing any component from the machine, note the cable routing that will be affected.
Whenever servicing the machine, you must carry out the following : 1. Check to verify that documents are not stored in memory. 2. Unplug the power cord. 3. Use a at and clean surface. 4. Replace only with authorized components. 5. Take care when removing plastic component-do not force. 6. Make sure all components are in their proper position.
Samsung Electronics
3-1
2. Take out the Shield Main Upper.Unplug the one connector and CCD cable.
2 1
Front Cover
Notice :
To avoid damage to the CCD cable connector ensure that you pull the cable out carefully. Pull in line with the connector not at an angle.
3-2
Samsung Electronics
8. Open the ADF Assy in the direction of arrow. Pull the ADF Ass'y upward and remove it.
9. Remove the three screws securing the Platen Ass'y. 7. Remove the connector from the Platen Ass'y.
Samsung Electronics
3-3
10. Pull the OPE Ass'y and unplug the one connector.
12. Unlatch the Scan Upper Ass'y securing the glass and remove it.
Notice :
When dismantling the Scan Assy ensure your work area is clean. Dirt or dust on the scan head can lead to a degradation in scanned image quality.
13. Remove the two scews and pull the Dummy Upper Assy.
3-4
Samsung Electronics
CCD Cable
17. Pull up the Shaft CCD and take out the Scanner Module.
18. Remove three screws and take out the Motor Bracket.
Samsung Electronics
3-5
19. Remove the OPE Harness from the Platen PBA. Remove two screws and take out the Platen PBA.
Notice :
Take special care when reassembling the CCD Module onto the Platen Ass'y. The CCD Module is located just to the right side the Belt Tension Spring as shown below.
Scanner Module
3-6
Samsung Electronics
Samsung Electronics
3-7
6. Take out the Pick-up Assy. Remove the four screws and the ADF Upper.
7. Remove three screws and take out the ADF Motor ass'y.
Pick-up Assy
ADF Upper
3-8
Samsung Electronics
2. Remove ten screws securing the OPE PBA and the LCD Module from the OPE Cover.
Caution
The above information is for the SCX-5315F model. For the SCX-5115 model, the OPE Assy is slightly different, prats maked a are not tted.
Samsung Electronics
3-9
* MP-Tray
1. To dismantle the MP tray release the lower hinges (1).
2. Completely open the Side Cover door. The left hand hinge (1) should be lifted to free it. Then push the whole door assembly to the left to free the right hand hinge (2).
2. As shown in (1) below align the door supports in a horizontal position. This will allow the TrayCase to be removed from the Tray Links. To remove the Tray-Links adjust the position of the Tray Link to a 45?angle to align the slot in the
2
MP Tray
3 1
Tray Link
Tray-Case
3-10
Samsung Electronics
* Duplex Assy
1. To remove the Duplex Ass'y from the Side Door Ass' locate the plastic clips, 2 on each side, and release them.
Duplex Assy
Samsung Electronics
3-11
Cover Bracket
Halogen Lamp
3-12
Samsung Electronics
6. Remove the two screws and take out the Halogen Lamp.
7. Remove 2 screws and hinge open the Lower Fuser Ass'y, remove the Heat Roller Ass'y from the Upper Fuser Ass'y.
Thermostat
Heat Roller
Samsung Electronics
3-13
2. Remove four screws, and then untie the harness from the Exit Upper. Unplug four connectors and unlatch the Dummy Base Frame, as shown below.
3-14
Samsung Electronics
Drive Assy
3. Remove the one screw and take out the Fan and Dust Fan.
Samsung Electronics
3-15
3-11 SMPS
1. Before you remove the LSU, you should remove: - Rear Cover (see page 3-1) - Scanner Ass'y (see page 3-2) - Cover Paper Exit Assy(see page 3-12) 3. Unplug the all connectors.
2. Remove three screws and take out the Shield SMPS Upper.
SMPS
3-16
Samsung Electronics
LSU
Samsung Electronics
3-17
2. Remove the one screw and take out the Panel Connect MPF.
3-18
Samsung Electronics
2. Remove the OPC Ground Screw (see diagram). Take care when re-assembling as if the thread is stripped the OPC ground may become intermittent causing print faults. Then remove the rest of the ve screws to dissassemble the Dummy Base Frame, the Cover Front and the Exit Roller release cam.
OPC Ground Screw
5. Remove the seven screws and take out the Main Frame Ass'y.
Main Frame Assy
Front Cover
3. Remove the Deve Lock Lever, and then remove the one screw and the Cover Motor Bracket.
Cover Motor Bracket
Lock Deve
Samsung Electronics
3-19
3-15 MP Ass'y
1. Before you remove the MP Assy, you should remove: - Rear Cover (see page 3-1) - Shield Main Upper (see page 3-2) - Side Cover Ass'y (see page 3-9) 4. Remove the three screws.
5. Release the SMPS t. Pull the MP Ass'y upward and remove it.
3. Remove the one screw and take out the Dummy Cover.
MP Assy
Dummy Cover
3-20
Samsung Electronics
Feed Assy
Feed Assy
Samsung Electronics
3-21
Cassette Rail
4. Remove the four screws and take out the Pick Up Ass'y, as shown below.
Pick-up Assy
3-22
Samsung Electronics
Main PBA
2. Remove the two screws and take out the Shield Main Lower.
LIU PBA
(Only SCX-5315F)
Main PBA
Samsung Electronics
3-23
Troubleshooting
COMPONENT ADF Rubber ADF Roller Pick-up Roller Transfer Roller Fuser Toner Cartridge Drum Cartridge
REPLACEMENT CYCLE 20,000 Pages 50,000 Pages 75,000 Pages 75,000 Pages 75,000 Pages 6,000 Pages 15,000 Pages
Samsung Electronics
4-1
Troubleshooting
DOOR OPEN
The side door and front door must be closed in the correct order. Open both doors. Close the front door rst then close the side door. Try again, check location for group.
You have tried to select a group location where only a single location number can be used, such as when adding locations for a multi-dial operation. Your unit cannot connect with the remote machine, or has lost contact because of a problem on the phone line. You have attempted to set up a sending operation with no document loaded. The memory has become full.
LINE ERROR
Usually caused by a telephone line problem. Try again. If failure persists, wait an hour or so for the line to clear then try again Load a document and try again. Either delete unnecessary documents, or retransmit after more memory becomes available, or split the transmission into more than one operation. Try again. Make sure the remote machine is OK. Dial the number manually with the keypad, or assign the number. Re-load the paper cassette. Your unit will automatically return to the standby mode when it cools down to normal operating temperature. If failure persists, call service. Press STOP and clear the jam.
The remote machine was not answered after all the redial attempts. The speed dial location you tried to use has no number assigned to it. There is no paper in the paper cassette. Printing stops until paper is loaded. The printer part has overheated.
PAPER JAM 0 OPEN/CLOSE DOOR PAPER JAM 1/2 OPEN/CLOSE DOOR TONER LOW
Recording paper has jammed in paper feeding area. Recording paper is jammed in pick-up unit Recording paper has jammed inside the unit. Recording paper has jammed in paper exit unit. Toner cartridge is almost empty, or toner particles in the cartridge are unevenly distributed in the cartridge Toner cartridge is now empty
Clear the jam. Remove the toner cartridge and gently rock it from side to side. Try again. If problem persists replace the cartridge. Replace the Toner Cartridge.
TONER EMPTY
4-2
Samsung Electronics
Troubleshooting
Description A warning that the OPC drum has almost reached the end of its life (14,000 Sides) OPC drum is now life-expired (15,000 sides) When the machine detects that the toner cartridge has not been installed. Paper feed problem from the BYPASS (Manual feed) Tray. Paper feed problem in the duplex return path
Solution You have 1000 pages of print life left in the OPC Drum. Continue to use, order a new OPC drum. Replace the OPC Drum Cartridge. Install the Cartridge. Open the side Cover and clear the jam. Release Output Feed lever and check output area clear. Also open side door and check duplex unit is clear. Try again. Check thermostat, thermistor, fuser lamp and fuser connector and associated wiring. Also check the Fuser On signal from main PWA to Power Supply. Check cable from Main PWA to Power Supply Check thermister contact point & Heating Lamp. Check transit lock, check scanner cables are connected, check scanner home sensor, scanner motor or drive belt.
During operation, Temperature does not go up Scanner head does not move.
Samsung Electronics
4-3
Troubleshooting
4-3-1 SCX-5315F
non SYSTEM DATA m CASSETTE PAPER BYPASS PAPER MESSAGE CONF. AUTO JOURNAL RECEIVE CODE POWER SAVE ECM MODE RX REDUCTION DISCARD SIZE REDIAL INTERVAL REDIALS ANSWER ON RING SEND FROM MEMORY LOCAL ID CLOCK MODE SYSTEM ID DATE & TIME SYSTEM SETUP PREFIX DIAL NO. SECURE RECEIVE RINGER VOLUME ALARM SOUND KEY SOUND SPEAKER CONTROL SELECT LANGUAGE USB MODE FAX DUPLEX IMAGE QUALITY SCAN SLEEP MODE HOME SET MEMORY CLEAR SYSTEM ID SYSTEM DATA PHONE BOOK / MEMORY TX-RX JOURNAL DELAY TX MEMORY TX PRIORITY TX POLLING ADD/CANCEL GROUP DIAL ADD / CANCEL LOW / HIGH (10 STEPS) ON / OFF ON / OFF COM / ON /OFF ENG/GER/FRE/ITA/SPA/POR/DUT FAST / SLOW OFF / LONG EDGE / SHORT EDGE NORMAL / TEXT / IMAGE FAX / ID onn LETTER / A4 / LEGAL LETTER / A4 / LEGAL ON / OFF / ERROR ON / OFF 0-9 ON / OFF ON / OFF ON / OFF 0-30mm 1-15 1-13 1-7 ON / OFF ON / OFF 12 / 24 HOUR
4-4
Samsung Electronics
Troubleshooting
non MAINTENANCE
onn
TX CONFIRM SCHEDULE JOB PHONE BOOK SYSTEM LIST TX JOURNAL RX JOURNAL HELP LIST HELP LIST
4-3-2 SCX-5115
non SYSTEM DATA m CASSETTE PAPER BYPASS PAPER POWER SAVE SELECT LANGUAGE USB MODE HELP LIST MAINTENANCE REPORTS HELP LIST CLEAN DRUM NEW DRUM SYSTEM DATA HELP LIST HELP LIST onn LETTER / A4 / LEGAL LETTER / A4 / LEGAL ON / OFF ENG/GER/FRE/ITA/SPA/POR/DUT FAST / SLOW PRINTOUT
Samsung Electronics
4-5
Troubleshooting
4-6
Samsung Electronics
Troubleshooting
non REPORTS
m MSG. CONFIRM SCHEDULE JOB PHONE BOOK SYSTEM DATA TRANSMISSION RECEPTION HELP LIST PROTOCOL ERROR CODE
onn
4-4-2-2 SCX-5115(SETUP : #, 1, 9, 3, 4)
non SYSTEM DATA m CASSETTE PAPER BYPASS PAPER POWER SAVE SELECT LANGUAGE USB MODE MAINTENANCE CLEAN DRUM MODEM TEST NEW DRUM SWITCH TEST SRAM TEST DRAM TEST ROM TEST PATTERN TEST CLEAR COUNT FLASH / ENGINE PATTERN1-7, QAPATTERN1-4 , ALL PASSWORD CRU PRINTS COUNT FLT SCAN COUNT ADF SCAN COUNT USED DRUM COUNT USED TONER COUNT TOTAL PAGE COUNT ADJUST SHADING FLASH UPGRADE REPORTS SYSTEM DATA HELP LIST ERROR CODE HELP LIST onn LETTER / A4 / LEGAL LETTER / A4 / LEGAL ON / OFF ENG/GER/FRE/ITA/SPA/POR/DUT FAST / SLOW
Samsung Electronics
4-7
Troubleshooting
SILENCE TIME
In ANS/FAX mode, after a call is picked up by the answering machine, the machine monitors the line. If a period of silence is detected on the line at any time, the call will be treated as a fax message and the machine begins receiving. Silence detection time is selectable between limited (about 12 seconds) and unlimited time. When '12 sec' is selected, the machine switches to receiving mode as soon as it detects a period of silence. When 'unlimited'is selected, the machine waits until the answering operation is concluded even though a period of silence is detected. After the answering operation is concluded, the machine switches to receiving mode.
ERROR RATE
Tou can set the Error Rate between 5% and 10%. During operation the set monitors the rror rate. When the rror rate approaches the preset value the machine automatically steps down the baude to 2400bps to ensure that the selected error rate is not exceeded.
MODEM SPEED
You can set the maximum modem speed. It is better left set 33.6Kbps (the default setting ). During call setup the baud rate is automatically adjusted to suite the slowest device. Only adjust this where the local line conditions are extremely poor.
NOTICE : Always perform a memory clear after replacing the main board or updating the rmware. Otherwise, the system may not operate properly.
4-8
Samsung Electronics
Troubleshooting
4-4-5 MAINTENANCE
CLEAN DRUM
Use this feature to remove toner particles remaining in the OPC drum unit. Use this feature when print quality falls or when marks or specks appear on the printout. You should perform this feature several times until a clean printout appears. The machine automatically pulls in a sheet of paper and prints out. Excess toner particles on the OPC drum surface are xed to the paper.
FLASH UPGRADE
This function is used to update the system Firmware. There are 2 methods Local and Remote. More information can be found in the rmware upgrade section.
ADJUST SHADING
This option is used to test and check the functionality of the CCD (Charge Coupled Device). Use this when poor quality scanning or copying is reported.
NOTICE : When you test the CCD, make sure that the cover is closed.
ANSWER ON CNG
The function is to control the CNG TONE recognition times for entering receiving mode from the AUTO MODE or ANS/FAX MODE.
Samsung Electronics
4-9
Troubleshooting
CLEAR COUNT
This function erases the counters stored in system memory. These are shown in the highlighted area in the Sytem data List shown below (printed in TECH MODE) Note the Current Drum Page Count cannot be erased. This is cleared using the NEW DRUM function (USER MODE MAINTENANCE NEW DRUM)
FIRMWARE VERSION ENGINE VERSION EMULATION VERSION TOTAL PAGE COUNTS CRU PRINTS REPLACED TONER COUNTS REPLACED DRUM COUNTS CURRENT DRUM COUNTS PLATEN SCAN PAGE COUNTS ADF SCAN PAGE COUNTS
: : : : : : : : : :
1.00 1.00 PCL6 2.32 07-11-2001 PCL5e 1.48 07-19-2001 123 123 1 1 112 23 10
PATTERN TEST
Using this pattern printout, you can check if the printer mechanism is functioning properly. It is used in the production process and is not intended for Service use.
ROM TEST
Use this feature to test the machine'S ROM. The result and the software version appear in the LCD display. FLASH VER : 1.00 V ENGINE VER :1.00V
DRAM TEST
Use this feature to test the machine's DRAM. The result appears in the LCD display. If all memory is working normally, the LCD shows << O K >>
SRAM TEST
Use this feature to test the machine's SRAM. The result appears in the LCD display. If all memory is working normally, the LCD shows << O K >>
MODEM TEST
Use this feature to hear various transmission signals to the telephone line from the modem and to check the modem. If no transmission signal sound is heard the modem may be faulty.
SWITCH TEST
Use this feature to test all keys on the operation control panel. The result is displayed on the LCD window each time you press a key. 4-10 Samsung Electronics
Troubleshooting
PROGRAM DIAL
This is a special feature which allows the TECH USER to set parameters for a specic dialed location (which must be in the one touch or speed dial phone books). Parameters can be set to override the normal; default settings to enable the machine to cope with calls to destinations with known line problems
4-4-6 REPORT/HELP
MSG. CONFIRM
It shows the result of the last send operation.
PROTOCOL LIST
This list shows the sequence of the CCITT group 3 T.30 protocol during the most recent sending or receiving operation. Use this list to check for send and receive errors. If a communication error occurs while the machine is in TECH mode, the protocol list will print automatically.
Facsimile Information Field data described in hexdecmal code Sending/Receiving Name of signal (Facsimile Control Field) FIF data described in ASCII code
NOV-20-2001
S/R FCF S S S S S S R R S R R S R S S
FIF DATA!
ASCII
NSF 61005820003380140200001302090018010000 CSI 2020202020202020202020202O20202020202020 DIS 00000000 01110111 00010111 00100010 NSF 61005020003380140200001302090018010000 CSI 202020202020202020202022O202020220202020 DIS 00000000 01110111 00010111 00100010 TSI 2020202020202020202020202O20202020202020 DCS 00000000 01100001 00010101 00000000 FTT TSI 2020202020202020202020202O20202020202020 DCS 00000000 01100001 00010101 00000000 CFR MPS MCF DCN
HELP
It shows a brief description on the machine's basic functions and commands. Use it as a quick reference guide
Samsung Electronics
4-11
Troubleshooting
RECEPTION
This journal shows information relating to document reception, the time and dates of up to 40 of the most recent documents received are stored.
TRANSMISSION
This journal shows information relating to document transmission, the time and dates of up to 40 of the most recent documents transmitted are stored.
SYSTEM DATA
This list provides a list of the user system data settings and tech mode settings.
PHONEBOOK
It lists all telephone numbers that have been stored in the machine.
SCHEDULE JOB
This list shows information relating to the documents currently stored for delayed transmission. It provides the operation number, starting time, type of operation, etc.
ERROR CODE
This list shows a list of errors that have occurred since the last memory clear.
4-12
Samsung Electronics
Troubleshooting
< Method > Press MENU, #, 1, 9, 3, # in sequence. The Firmware version is displayed on the LCD. Press 1( in the number keypad) : The LCD display shows "Updated date" Press 2( in the number keypad) : The LCD display shows "Product rst use date"
Samsung Electronics
4-13
Troubleshooting
4-5-2 Diagnostic
No. 0 Sub No. 1 2 3 4 Engine test Motor Test PTL T est Fan T es t Fus er Test 1: On, 1: On, 1: On, 2: Off 2: Off 2: Off Remark
1 : On, 2: Off If its temperature is lower than the Standby (160 C), the fuser is on, but if it is higher than the Standby, the fuser is off. 1: On, 1: On, 1: On, 1: On, 2: Off 2: Off 2: Off 2: Off
1 2 3 4
LSU Motor Test LSU Hsy nc Test LD On Test LSU Operation Feed Sensor T es t Exit Sensor Test Cov er Sensor Tes t
1 2 3
Sensor O n : FEED SENSOR ON Display Sensor O ff : FEED SENSOR OFF Display Sensor O n : EXIT SENSOR ON Display Sensor O ff : EXIT SENSOR OF F Display Sensor O n : COVER SENSOR ON Display Sensor O ff : COVER SENSOR OFF Display
4 5 6
1st Empty Test MP Empty Sensor Test BIN FULL Sensor Test 1st CAST Solenoid Test MP Solenoid Test Duplex Solenoid T es t MHV Test Dev Bias Test THV EN/NEG Tes t THV Tes t THV Trigger Test CRU Error Check New OPC Check All Function Test
Sensor O n : 1s t PAPER Empty Display Sensor O ff : 1s t PAPER No Empty Display Sensor O n : MP PAPER Empty Dis play Sensor O ff : MP PAPER No Empty Display Sensor O n : BIN FULL SEN ON Display Sensor O ff : BIN FULL SEN O FF Display
1 2 3
2: Off 2: Off 2: Off 2: Off (-1450v) 2: Off (-450v) 2: Off 2: Off (1300v) 2: Off
1 2 3 4 5
1 2
1: Check, 2: Next 1: Check, 2: Next For SMD Test, Pus h up k ey : Next function All Function : No.0~4
4-14
Samsung Electronics
Troubleshooting
4-6 Troubleshooting
4-6-1 Scanner
4-6-1-1 COPY
ITEMS TO BE CHECKED. Ensure the Scanner cover is closed. Check shading prole
HOW TO SOLVE Room lighting can penetrate thin paper causing quality problems Carry out the Adjust Shading procedure in Tech mode Check the CCD harness contact. Remake shading prole in the tech mode. Carry out the Adjust Shading procedure in Tech mode A gap above 0.5mm can cause a blurred image. See Print troubleshooting. Check scanner carriage, motor, gearbox, belt and belt tension spring If any driver is defective, replace it. - U2-4, 11, 18, 25 signals swing between OV and 24V when operating.
Black copy
Check shading prole. Check the original is laying at on the scanner glass. Check printing quality.
Abnormal noise
Check the Scanner drive mechanism. Check the Motor Driver chip on the driver PBA.
Samsung Electronics
4-15
Troubleshooting
4-6-1-2 PC-Scan
ITEMS TO BE CHECKED. Check the printer cable is correctly installed. Check that the TWAIN driver is installed.
Remove any other scanner driver. Reboot after reinstallation of the TWAIN driver. Check the parallel-port-related items in the CMOS Setup. As a printer port, ensure ECP is selected. Check CN12 contact in Main PBA If any signal level is defective, replace driver PBA. - U33-26, 27, 28, 43, 44, 45, 46, 47 on Main PBA are 0.8V to 2.4V TTL signal. Otherwise, replace Main PBA. If USB signal level is defective, replace Main PBA. Remake shading prole in the tech mode.
Check the gap between original and scanner glass. Abnormal noise Check the Scanner Motor and any mechanical disturbance.
The gap above 0.5mm can cause a blurred image. Check the right position of the Scanner Motor, and check the any mechanical disturbance in the CCD carriaging part. If any driver is defective, replace it. - U2-4, 11, 18, 25 = 0V to 24V swing signal when operating.
4-16
Samsung Electronics
Troubleshooting
Cannot MF dial
Replace defective parts. Replace LIU PBA if low. Refer to TEL LINE CANNOT BE ENGAGED above. Replace main PBA, if abnormal. Replace LIU PBA if CN1-1(LIU PBA) is not conrmed. Replace main PBA if CN20-1(MAIN PBA) is not conrmed. Replace LIU PBA if it cannot be checked. Refer to Defective Transmission.
Samsung Electronics
4-17
Troubleshooting
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
No image 1. OPC is properly grounded? 2. LSU running well? 3. Bias voltage is correct? 4. Toner low? 5. Is there video data from Main PBA 1. Measure the resistance between frame ground and the OPC ground spring attached to the frame. Conrm good ground. If faulty check ground path through the frame . Also check OPC Ground Screw see page 3-18 2.Adjust LSU or replace it 3. Normal Dev bias = -440V 4. Shake toner cartridge and print. If an image appears toner is empty 5. Print engine test pattern , replace Main PBA 1. Checking LSU light power is difcult. Compare with new one and check. 2. Check toner and developer counter 3~4. Change the HVPS Board. 5. Stray toner can increase contact resistance and cause a bad contact. Clean contaminated area.
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Light image
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Dark image
1. LSU light power normal? 2. Enough toner? 3. High charger voltage? 4. Lower bias voltage 5. Contamination of high voltage contact. 6. Transfer voltage and roller.
1. LSU light power normal? 2. Bias voltage output is high? 3. Video data is always supplied? 4. Bad C/R voltage contact.
1. Checking LSU light power is difcult. Compare with new one and check. 2. Normal Dev bias = -350V 3. Check Video Data signal(CN2). Replace main PBA board. 4. Replace Drum Cartridge or check where is bad point of machine.
4-18
Samsung Electronics
Troubleshooting
Solution 1. Change the HVPS Board. 2. Print a number of Cleaning sheets if problem persists change the cartridge..
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Ghost 1. High voltage output. 2. Pre-Transfer Lamp. 3. Bad high voltage contact.
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Stains on back of paper
1. Change the HVPS Board. 2. Check PTL lamp comes on replace if necessary 3. Clean the inside machine or replace toner cartridge.
1. Contamination of transfer roller. 2. Toner debris in paper path 3. Pressure roller contamination
1. Clean the transfer roller with vacuum cleaner. 2. Clean the paper path with a cloth or air duster. 3. Remove fuser and replace it.
Poor Fusing
1. Paper quality and nish? 2. Check fusing temperature. 3. The machine was kept at a low temperature for a long time?
1. Should use recommended paper. 2. Check engine controller board. If you do not have a thermometer, measure the thermistor voltage to CPU, If 2.3V5% when printing is correct therwise disassemble fthe user and check the thermistor contacts and thermistor. 3. Re-check after allowing the machine to come up to room temperature.
Measure the spacing of the marks and compare the spacing to those given in the table below. Spacing 1 and 2 Replace the OPC Spacing 3 and 4 replace the toner car tridge Spacing 5 replace the transfer roller Spacing 6 and 7 replace the Fuser.
Samsung Electronics
4-19
Troubleshooting
Check 1. Uneven pressure between Charge roller and OPC Drum 2. Uneven pressure between Dev roller and OPC drum 3. Transfer rollers pressure force uneven at each side
Solution 1. Change OPC cartridge 2. Change toner and / or OPC Drum 3. Check left and right transfer roller springs
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
1. Bad contact on high voltage terminal 2. Contamination of charge roller 3. Contamination of heat roller 4. Malfunction of LSU
1. Clean each contact and check continuity 2. Print several cleaning sheets replace OPC drum if problem persists. 3. Replace fuser unit 4. Check Main PBA., LSU harness and LSU
4-20
Samsung Electronics
Troubleshooting
No Image
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
No image?
NO
A on next page
YES
Self test pattern prints? YES Check connection to computer or replace controller
NO
NO
Take out the cartridge and prepare the tester for electronic connection
NO
Does the video data line to LSU transit to High/Low when printing? YES
NO
Check the path between Main board and HVPS. Repair or replace the defective component or board
The mirror in LSU might be misplaced so the light path to the OPC deviates ->Repair or replace LSU or remove any defective matters in the machine
Samsung Electronics
4-21
Troubleshooting
NO
NO
NO
Is the connection terminal OK? YES Replace HVPS or repair defective component
NO
Does the counter indicate over the toner's guaranty life YES
NO
Transfer roller might be out of its location -> Locate the roller into its place This could occurs when he power of LSU is low or the density is low due to the obstacles on the window -> Replace LSU or clean the window
4-22
Samsung Electronics
Troubleshooting
All Black
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
NO
Does the video data line to LSU transit to High/Low when printing? YES
NO
Check the path among video controller, engine board, HVPS, LSU for the shortage or open -> Repair or replace the boards
Replace LSU
NO
NO
Replace LSU
Samsung Electronics
4-23
Troubleshooting
NO
Check if the printout is still has the same problem even right after passed through the transfer roller YES
NO
The ribs in fuser or toner on the roller may invoke the image problem -> Replace the fuser cover or the defective part The image is originally black or the black part is far close to the top -> Use the pattern which has the image below bigger than 10mm from the top
YES
Dirt of dust stuck onto the window of internal lens of LSU -> Clean it or replace LSU Preventive obstacles through the path between OPC of developer and LSU prevent the path -> Remove the obstacles
Toner material might be stuck to blade in the developer inside and it prevents toner supply -> Replace the developer Check both if the toner cartridge's counter is over its guaranty and amount of the toner material -> Replace the toner cartridge
4-24
Samsung Electronics
Troubleshooting
Dark Image
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
NO
END
NO
NO
Toner over supply due to the adjustment fault of metering blade in developer -> Replace developer
The power of LSU is set high or internal problem -> Replace LSU or adjust volume
Samsung Electronics
4-25
Troubleshooting
Background
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
NO
- Adjust voltage or replace HVPS - Repair or replace after checking the terminals' contacts
NO
YES
NO
END
NO
NO
Solve the problem under the recommended condition (10-32 degree Centigrade)
Clean the charge roller or replace step-up device /terminal after check
Check Terminals or contacts and 'Guide-Deve Spring' are misplaced -> Repair or replace transfer roller etc. Check if the LED of PTL in front of the transfer roller is on when it presses the top cover switch on purpose -> If not, replace PTL
NO
Internal blade or supplying part of the developer is defective -> Replace the toner cartridge
4-26
Samsung Electronics
Troubleshooting
Ghost
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
NO
NO
NO
A specific part of the transfer roller has ruined or its resistance value is changed -> Replace transfer roller Transfer roller cannot force regularly due to the gears eccentricity of transfer roller -> Replace the defective component
Check HVPS contacts and HVPS's selfoutput -> If failed, repair/replace HVPS
NO
NO
- Repair or replace HVPS - Check and Repair or replace the terminal contacts
NO
YES
Operating/storage temperature is too low or not recommended paper used? YES Use the machine with recommended paper and at condition
NO
There may be a problem in toner layer control in toner cartridge -> Replace the developer
Samsung Electronics
4-27
Troubleshooting
Black Spot
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
NO
NO
NO
The problem randomly occurred due to the toner fallen -> Clean the machine
The problem occured since the obstacles stuck to charge roller -> Clean the Charge Roller and then reprint.
Toner leaks and much toner material dropped onto the paper -> Replace the developer
Check toner is stuck onto the P/R or H/R in fuser -> Clean it or replace
4-28
Samsung Electronics
Troubleshooting
Horizontal Band
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Black band?
NO
NO
The OPC is damaged under the direct sunlight for around 5 minutes -> If the same problem persists in 10 hours, replace the developer
NO
94mm interval?
NO
NO
YES
Problems of terminal contact, transfer voltage supplying, and transfer roller's due to the charge roller is ruined (38mm) -> Repair/replace HVPS, developer
The OPC is damaged due to the irregular transfer voltage of HVPS -> Repair/replace HVPS -> If the same problem persists, replace the developer
Samsung Electronics
4-29
Troubleshooting
Irregular Density
NO
NO
NO
Defective agitator in the toner supplying part of developer ->Replace the developer Check if the 'guide deve spring' works OK and repair/repalce
It is over the guaranty life of toner cartridge (Check the counter and replace it)
NO
Replace lamp
NO
Light distortion due to the mirror ruined or LSU's diffused reflection -> Replace LSU
4-30
Samsung Electronics
Troubleshooting
White Spot
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
NO
NO
Too high voltage supplied due to the setting error of transfer voltage -> Adjust/replace HVPS
YES
Obstacles stuck on OPC's surface -> Clean the OPC and machine or replace developer When putting in/out the developer, scratch is made -> Replace the developer
D/R in developing unit has the defect -> Replace the developer
Samsung Electronics
4-31
Troubleshooting
NO
NO
When OHP printing, does the fan temporarily stops and revolves? YES
NO
When multi-page OHP printng, less than 10 films are guranteed. (Reduce the number of films and re-insert after paper check LED if off)
Other parts are touching the fan and prevents it from revolution -> Check and repair
4-32
Samsung Electronics
Troubleshooting
The machine placed under the severe low tempera ture for a long time?
NO
While printing, the voltage of pin 60 of U36 (CPU) on Main PBA is 2.1V - 2.6V?
NO
NO
YES
YES
YES
YES
NO
Re-assemble thermistor
YES
Open the top cover. When black printing, is the fuser NIP width is 3.03.5mm?
NO
Check if the hardness of P/R, and spring force is OK? (hardness: 24 degree, spring's force: 3 Kg)
YES
Replace the control component on Main PBA Check any contact problem in thermistor and repair
The paper used is too thick or contains too much cotton in it -> Re-test with the recommended paper
Samsung Electronics
4-33
Troubleshooting
4-6-4 Malfunction
Error Status No power Check 1. Check power is supplying 2. Check fuse F1 open Fuser Error 1. Thermostat open Solution 1. If supplying power differs from machines power rating, replace the machine. 2. Replace it. 1. Detach AC connector and measure the resistane between pin 1 and 2. If it is megohm, thermostat is open, Replace it. 2. Check bad connector contact or wire is cut. 3. Check thermistor wire and its connection. 4. Replace Main PBA 1. Open Side cover and press the lever with pen. If Controller detects cover close, there is some mechanical trouble in Side cover and levers assembly. If not so there is electrical problem.
2. AC wire open 3. Thermistor wire open 4. Main PBA Cover open 1. When close Side cover, check the lever is pressed 2. Micro switchs contact 3. CPU and related circuit Check where Jam 0 happens 1. Paper is not picked up 2. Paper is located in feed sensor 3. Happened when inserting specic papers such as envelope into the MPF (Multipurpose Paper Feeder)? 4. Happened when inserting specic papers such as envelope into the Manual Feeder?
Jam 0
1. Check whether solenoid is working or not by using Engine test mode 2. Check feed sensor malfunction. 3. Re-try inserting a fewer papers.
fan the papers and align take out the loaded papers and insert them reverse direction
4. Take out the loaded papers and insert them reverse direction inserted papers as recommended for Manual Feeding? When loading, tap the papers until paper detect sensor senses loading 5. When using long papers, use the Stacker Extender 6. Adjust Guide to t the paper width 1. It is mostly resulted from double feeding. Check paper is well stocked in feeder. 2. Check feed actuator position and actuators operating. There may be stiff movind or double reection. If not so, check the operation of feed sensor by Engine test mode. 3. Check exit lever operation. Remore jam and check actuator moving by hand. If actuator is too stiff, paper is wrapped around the heat roller. Remove obstacles or replace. 1. Remove paper using pinset or some tool and watch if separate claws have any troble. Clean around fuser. 2. Check locking works wells. Watch whether the ribs of exit cover hace any burr or resisitive edge. If they do, remove obstacles or replace.
5. Is the Stacker Extender is folded out? 6. Does not the Guide Adjust distort the papers Jam 1 Paper is stopped in just after of fuser unit.
Jam 2
Check where Jam 2 happens 1. Paper is curled and cannot exit. 2. Paper is curled in the exit cover?.
4-34
Samsung Electronics
Troubleshooting
Error Status
Check 1. Then paper is not drawn in because of the stack of papers in the Out tray. 2. Does it curl while coming out?
Solution 1. Load recommended quantity of papers 2. Open the Cover Front and check whether roller or spring, which are related to paper out, is not out of position. If so, re-locate or replace. 1. Check whether the spring is expanded or not. 2. Check armature is well installed. It may be unstable assemble. 3. Remove the Main PBA. 1. Remove the Toner cartridge and open the cover and press cover open switch lever and measure the voltage with high voltage probe and sending printing data. If the voltage is normal, change the toner cartridge. 2. Disassemble the left side cover, and check HV of the solder side of HVPS and change it. MPF : Turn the power off and on. Open and close the Side cover to return to the original state. Cassette : Adjust Guide to t the paper width.
Clutch error
1. Check the spring of solenoid 2. Check the armature assembly/cushion 3. Electrical check
2. Check HVPS
Feeding obstacles
Skew
Stacking
1. Use extender as per the paper length. 2. The Face-up stacker normally can hold 100 pages when using 75g/m2, however, stacking capacity can be lowered depending on the type of papers. Refer to troubleshooring ENGINE ERROR.
1. Check document is well stocked in ADF. 2. Check whether document was been fastened together by staple or clip. 3. Load recommended quantity of papers. 1. Check whether the Reg. sensor is working or not. 2. Check whether the Feed Roller is working or not. 1. Check the Open Cover whether there are bosses. 2. Check the ADF ass'y is well assemble.
Document is stopped after it has fed into the ADF. Does it curl while coming out?
Samsung Electronics
4-35
Troubleshooting
NO
NO
NO
NO
NO
The connection error between controller board and panel board or malfunction of boards. -> Replace the boards
NO
NO
Detect failure due to the board which detects side cover open or switch error -> Replace the board or switch
4-36
Samsung Electronics
Troubleshooting
Fuser Error
Measure the resistance at the both ends of AC Line with covers open
Thermostat is open due to the heat etc. -> Replace the thermostat
YES
AC is being supplied?
NO
The voltage of pin #6 of U5 on the Main PBA is about 3.2V? If not check the CN4 on the power board.
YES
The voltage of pin #60 of U36 (CPU) on the Main PBA is about 2.65V when printing? YES
NO
Thermistor, connecting point or engine board defect -> Repair/replace the component/board
END
Samsung Electronics
4-37
Troubleshooting
NO
NO
NO
Switch them
NO
NO
NO
YES <Recommendation> Use the MPF for the thick paper such as envelope and cardstock
4-38
Samsung Electronics
Troubleshooting
Paper Jam(Jam 1)
Check the actuator exists and its operation and around the Main PBA -> Replace
NO
YES
Check the roller and ribs of fuser are in place, and remove burrs, if any -> Remove the factors of jam
Remove the fuser, remove the paper and replace the pressure roller, if necessary
NO
The paper came out through between fuser and developer? YES
NO
Adjust the paper guides to fit the paper width The force of springs pressing the developer is weak -> Check guide-DEVE
NO
Samsung Electronics
4-39
Troubleshooting
Engine Error
NO
NO
NO
Replace LSU
NO
NO
Replace LSU
END
4-40
Samsung Electronics
Troubleshooting
It is not guaranteed for the default caused by using other toner and Drum Cartridge cartridge other than the cartridge supplied by the Samsung Electronic or caused by non-licensed rell production.
Samsung Electronics
4-41
Troubleshooting
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
2. In case of 2If it becomes better after cleaning the LSU window, then the developer is normal. (Because of foreign substance on the LSU window, the image has not been printed partly.)
3. In case of 3If the cycle of noise is about 2 seconds, the toner inside the developer has been nearly exhausted.( Purchase and replace with a new developer after using about 200 sheets at the point of occurrence)
4. White vertical stripes on the whole screen or partly : Check the weight of the developer.
4. In case of 3This is a phenomenon caused by lack of toner, so replace with a new developer.
Toner Contamination
Toner is fallen on the papers periodically. Contaminated with toner on prints partly or over the whole surface.
1. Toner is fallen on the paper periodically. (1)Check the cycle of the falling of the toner. (2)Check the appearance of both ends of the developer OPC drum. 2.The center of the printed matter is contaminated with toner. (1)Check whether foreign substances or toner are stuck to the terminal (contact point) of the developer. (2)Check whether the state of the terminal assembly is normal.
1. If both ends of the OPC drum are contaminated with toner: Check the life of the developer.
4-42
Samsung Electronics
Troubleshooting
Signs Light or dark black dots on the image occur periodically. White spots occur in the image periodically.
Cause & Check 1. If light or dark periodical black dots occur, this is because the developer rollers are contaminated with foreign substance or paper particles. (1)37.7mm interval : Charged roller (2)94.3mm interval : OPC cycle
Solution 1. In case of 1 above Run OPC Cleaning Mode Print 4-5 times repeatedly to remove. Especially check foreign substance on the OPC surface, then remove them with a clean gauze moistened with IPA(Isopropyl Alcohol) not to damage OPC if necessary. Caution : Never use usual alcohol.
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
2. If white spots occur in a black image at intervals of 94.3 mm, or black spots occur elsewhere, the OPC drum is damaged or foreign substance is stuck to the surface.
2. In case of 2 If they are not disappeared by running OPC Cleaning Mode Print 4-5 times. : at intervals of 94.3mm Replace the OPC Drum. : at intervals of 37.7mm Remove foreign substance, Clean the Charged Roller : Broken image Replace the developer according to carelessness.
3. If a black and white or graphic image is partially broken at irregular intervals, the transfer roller's life has been expired or the transfer voltage is abnormal.
3. In case of 3 - Exchange the transfer roller because the life of the transfer roller in use has been expired. (Check the transfer voltage and readjust if different.)
Recycled product
Poor appearance of the developer. Unclean and rough printouts. Bad background in the image.
1. Poor appearance of the developer. (1)Check the damage to label and whether different materials are used. (2)Check the appearance of parts of the developer, such as frame, hopper.
1. In case of 1 (1)If there is an evidence of disassembling the developer. (2)If materials other than normal parts of the developer are added or substituted.
2. Unclean and rough printouts. (1)Check whether foreign substance or toner are stuck to the terminal (contact point) of the developer. (2)Check whether the state of the terminal assembly is normal.
2. In case of 2 - If there are any abnormals in connection with the situation of 1. (1)It occurs when the developer is recycled over 2 times. (2)If toner nearly being expired are collected to use, it is judged as the recycled developer.
Samsung Electronics
4-43
Troubleshooting
Signs The printed image is too light or dark, or partially contaminated black. Totally contaminatedblack. (Black image printed out)
Cause & Check 1. The printed image is too light or dark, or partially contaminated black. (1)Check whether foreign sub stance or toner are stuck to the terminal(point of contact) of the developer. (2)Check whether the terminal assembly is normal.
Solution 1. All of 1, 2, 3 above (1)Remove toner and foreign substances adhered to the contact point of the developer. (2)The contact point of the unit facing that of the developer also must be cleaned. (3)If the terminal assembly is unsafe: Fully stick the terminal to or reassemble it after disassembling. Disassemble the side plate and push the terminal to be stuck, then reassemble it.
2. Totally contaminated black. (Black image printed out) (1)Check whether foreign sub stances are stuck to the terminal(point of contact) of the developer and the state of assembly. (Especially check the charged roller terminal.)
2. In case of 2 It is a phenomenon when the OPC drum of the developer is not electrically charged. Clean the terminals of the charged roller, then recheck it.
4-44
Samsung Electronics
Troubleshooting
4-6-6 The cause and solutions of bad environment of the software 4-6-6-1 The printer is not working (1)
Description : While Power turned on, the printer is not working in the printing mode.
Check and Cause 1. Check if the PC and the printer is properly connected and the toner cartridge installed.
Solution 1. Replace the printer cable. If the problems not solved even after the cable replaced, check the amount of the remaining tone. 2. Check if the connection between PC and printer port is proper. If you use windows, check if the printer driver in the controller is set up. If the printer driver is properly set up, check in which program the printing is not working. The best way to nd out is to open the memo pad to check the function of printing. If it is not working in a certain program, adjust the setup the program requires. Sometimes, the printout is normal within the Windows basic programs, but it's not working in a particular program. In such case, install the new driver again. If not working in the Windows basic program, Check the setup of the port of CMOS is on ECP. And check the address of IRQ 7 and 378 3. If the scanner needs to be connected to the printer, rst the remove the scanner from the PC to see if the printer is properly working alone.
Solution 1. Not working with the message 'insufcient printer memory' means hard disk space problem rather than the RAM problem. In this case, provide more space for the hard disk. Secure more space using the disk utilities program. 2. The connection of the cable and printer port is not proper. Check if the connection is properly done and if the parallel port in CMOS is rightly set up. 3. As a printer port, Select ECP or SPP among SPP(Normal), ECP, and EPP modes(increase printing speed) SPP normal mode support 8-bit data transfer, while ECP Mode transfer the 12-bit data. 4. If the regular font is not printing, the cable or the printer driver may be defective. Turn the PC and printer off, and reboot the system to print again. If not solved, double-click the printer in my computer If the regular fonts are not printed this time again. the cable must be defective so replace the cable with new one.
2. Printing error occurs even if there is enough space in the hard disk.
Samsung Electronics
4-45
Troubleshooting
Check and Cause 1. Set up the parallel port in the CMOS SETUP.
Solution 1. Select SPP(Normal) or ECP LPT Port the among ECP, EPP or SPP in the CMOS Setup.
2. Check the printer in My Computer.(to see if the printer driver is compatible to the present driver or delete the old driver, if defective and reinstall the new driver) 3. Delete the unnecessary les to secure enough space of the hard disk and start printing job again.
3. Error message from insufcient memory. (The printing job sometimes stops or due to insufcient virtual memory, but it actually comes from the insufcient space of the hard disk.)
Check and Cause 1. Insufcient space of the hard disk in the directory assigned for the basic spool. 2. If the previous printing error not solved.
Solution 1. Delete the unnecessary les to provide more space to start printing job. 2. If there are some les with the extension name of ****.jnl, Delete them and Reboot the Windows to restart printing job. 3. Shut down all other programs except the current one, if possible. 4. Delete the printer driver completely and reinstall it.
4. When an application program or the printer driver is damaged. 5. When some les related to OS are damaged or virus infected.
5 After rebooting the computer, check for viruses, restore the damaged les and reinstall the program to do the printing job. 6. Add up enough memory to the PC.
4-46
Samsung Electronics
Appendix information
The following list shows different materials by model. The material codes mentioned in themanual are subject to change without prior notice. For the latest exact information, see ITSELF SYSTEM. (http://itself.sec.samsung.co.kr)
SCX-5315F/XAA
DESCRIPTION SEC.CODE
SCX-5115/XAA
DESCRIPTION SEC.CODE
ELA HOU-SCANNER ELA HOU-PLATEN(SEC) ELA HOU-OPE(SEC) PMO-COVER OPE(C) WINDOW-LCD(4IN1) PMO-COVER DUMMY OPE(M) PCT-ONETOUCH PAPER PBA SUB-LIU
ELA HOU-SCANNER ELA HOU-PLATEN ASSY ELA HOU-OPE COVER(SEC) PMO-OPE COVER PCT-LCD WINDOW(3 IN 1)
SCX-5315F/XEG
DESCRIPTION SEC.CODE
SCX-5115/XEU
DESCRIPTION SEC.CODE
ELA HOU-SCANNER ELA HOU-PLATEN(GER) ELA HOU-OPE(GER) PMO-COVER OPE WINDOW-LCD(GER 4IN1) PMO-COVER DUMMY OPE(M) PCT-ONETOUCH PAPER PBA SUB-LIU
ELA HOU-SCANNER ELA HOU-PLATEN ASSY ELA HOU-OPE COVER(SEC) PMO-OPE COVER PCT-LCD WINDOW(3 IN 1)
SCX-5315F/XEU
DESCRIPTION SEC.CODE
SCX-5115/XEG
DESCRIPTION SEC.CODE
ELA HOU-SCANNER ELA HOU-PLATEN(SEC) ELA HOU-OPE(SEC) PMO-COVER OPE(C) WINDOW-LCD(4IN1) PMO-COVER DUMMY OPE(M) PCT-ONETOUCH PAPER PBA SUB-LIU
ELA HOU-SCANNER ELA HOU-PLATEN ASSY ELA HOU-OPE COVER(SEC) PMO-OPE COVER PCT-LCD WINDOW(3 IN 1)
SCX-5315F/XIL
DESCRIPTION SEC.CODE
ELA HOU-SCANNER ELA HOU-PLATEN ELA HOU-OPE PMO-COVER OPE WINDOW-LCD(4IN1) PMO-COVER DUMMY OPE(M) PCT-ONETOUCH PAPER PBA SUB-LIU
Samsung Electronics
Samsung Electronics
5-1
5-2
1 34 44 5
21-2 21-1
1-1 16 37 18 21 33
1-2
(SCX-5315F)
1-2 7 37 11 38
40-2 40-140-3
(SCX-5115)
23
49
41
2 3 8
25
20 9
48
2-1
40
26-3 26-3
10
2-2
26-1
Samsung Electronics
26-2
26
DESCRIPTION
ELA HOU-SCANNER ELA HOU-SCANNER ELA HOU-ADF ELA HOU-PLATEN ELA HOU-PLATEN MEA UNIT-COVER PA EXIT ASSY PMO-TRAY EXTENTION MP NE PMO-COVER PAPER EXIT MEA UNIT-CASSETTE(KOR) MEA UNIT-COVER FRONT ASSY UNIT-LSU,600DPI,15 ELA ETC-SHIELD SMPS LOWER ELA ETC-SHIELD SMPS LOWER ELA ETC-SHIELD SMPS LOWER
SEC CODE
Refer to Info. Refer to Info. JC96-02750A Refer to Info. Refer to Info. JC97-01556B JC72-00354B JC72-00786B JC97-01736A JC97-01572B JC59-00014B JC96-02422A JC96-02310B JC96-02317A * * JC96-02715B JC96-02183B JC96-02182A JC96-02818A JC75-00143B JC96-02814A JC96-02815A JC96-02184A JC97-01643A JC96-02741A JC72-00788A JC92-01480A JC92-01479A JC63-00215B JC63-00215A JC96-02311A JC31-00012A JC72-00807A JC39-00055B JC33-00007A
QTY
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
SA
O O O O O O O O O O O O O O X X O O O O O O O O O O O O O O O O O O O O 110V 220V
REMARK
SCX-5115 SCX-5315F SCX-5115 SCX-5315F
7 8 9 10 11 12 13 14 15 16 17 18 19 19 20 20 21 21-1 21-2 23 24
ELA-OPC UNIT 15K D ELA-TONER UNIT 6K D ELA HOU-PICK UP ELA HOU-SIDE COVER ELA HOU-MP ASSY ELA HOU-BASE FRAME MEC-FEED ASSY ELA HOU-FUSER ELA HOU-FUSER ELA HOU-FRAME MAIN ASSY MEA UNIT-EXIT ASSY ELA HOU-DRIVE(15PPM) PMO-COVER REAR PBA MAIN-MAIN PBA MAIN-MAIN COVER-M-PANNEL MFP COVER-M-PANNEL MFP ELA HOU-DUCT FAN FAN-DC PMO-DUCT FAN CBF HARNESS-SWITCH GRAY SOLENOID-PICK UP
Samsung Electronics
5-3
DESCRIPTION
PMO-COVER EXIT REAR MEA UNIT-GUIDE CST PA ASSY PPR-SHEET/GUIDE PAPER PMO-GUIDE CASSETTE RAIL SHEET-FEED PBA SUB-LIU PMO-DUMMY BASE FRAME ELA HOU-SHIELD MAIN LOWER SHIELD-P-MAIN LOWER CBF HARNESS-INLET(KOREA) CBF HARNESS-LIU GND PMO-COVER FEED AY PMO-COVER BRKT MOTER PMO-GUIDE PAPER OUT SHEET-CONNECTOR CBF HARNESS-LSU CBF HARNESS-POWER+HVPS CBF HARNESS-LIU PMO-BEARING SHAFT GEAR-PICK_UP IPR-SHIELD SMPS UPPER MEA UNIT-HOLD GEAR ASSY SPRING ETC-TR_R PMO-BUSH PMO-HOLDER GEAR TR MEA UNIT-HOLD GND ASSY SPRING ETC-PLATE TR SPRING ETC-TR_L PMO-BUSH PMO-HOLDER GND TR SUPPORTER PMO-WINDOW SENSOR DEVE PMO-CAM JAM REMOVE PMO-LOCKER DEVE PMO-LEVER JAM REMOVE IPR-SHIELD SMPS LOWER GEAR-TRANSFER MEC-TRANSFER ROLLER
SEC CODE
JC72-00790A JC97-01575A * * * Refer to Info. JC72-00789A JC96-02835A * * JB39-00103A JC72-00801A JC72-00834A JC72-00835A JC63-00072A JC39-00163A JC39-00162A JB39-00104A JC72-41191A JC66-00335A JC70-00248A JC97-01573A * JC72-40228A * JC97-01574A * * JC72-40228A * 6103-001048 JC72-00792A JC72-00799A JC72-00805A JC72-00804A JC70-00247A JC66-40947A JC75-00148A
QTY
1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1
SA
O O X X X O O O X X O O O O O O O O O O O O X O X O X X O X O O O O O O O O
REMARK
Only SCX-5315F
5-4
Samsung Electronics
1-2
0
1-3
SCX-5315F
SCX-5115
1-5
2-17
2-6 2-19 2-18 2-20 2-7-4 2-7-6 2-7-3 2-7-7 2 2-8 2-7-1 2-7 2-22 2-7-2 2-7-4 2-7-5
2-21
2-3
Samsung Electronics
5-5
3-3
3-2 3-2 3-6 3-1 3-1 3-7 3-8 3-10 3-12 3-9 3-14 3-11 3-17 3-18 3-13 3-15 3-16 3-4 3-5 3-6 3-7 3-8 3-11 3-10 3-9
3-12
3-19
3-13
S6 S9
3-20 S6 S9 S6 S6
3-14
S6
S6
SCX-5315F
SCX-5115
5-6
Samsung Electronics
DESCRIPTION
ELA HOU-PLATEN ELA HOU-PLATEN ELA HOU-SCAN UPPER AS-DUMMY UPPER AS (FRV) MCT-GLASS ADF LABEL(R)-REGISTRATION EDGE(L) PMO-DUMMY UPPER SHEET-DUMMY UPPER PPR-REGISTRATION EDGE(F) PMO-COVER SCAN UPPER IPR-HOLDER GLASS MCT-GLASS SCANNER(LEGAL) ELA HOU-SCAN LOWER BELT-TIMING GEAR SPRING ETC-BELT CBF HARNESS-OPE CBF HARNESS-MAIN-ENGINE CBF HARNESS-DRIVER GND PBA SUB-D_SUB ELA HOU-SCAN MOTOR MOTOR STEP-SCAN BRACKET-MOTOR PLATEN GEAR-TIMING RING-E GEAR-REDUCTION73/37 PMO-HOLDER BELT GEAR IDLE COVER-M-CCD CABLE COVER-SCAN LOWER(UMAX) IPR-CHANNEL BASE FRAME HOLDER-M-CCD(UMAX) PMO-COVER DUMMY LOWER(C) ICT-INSERT SHAFT PMO-PULLEY PMO-HOLDER BELT RING-E SHAFT-CCD(UMAX) PMO-LEVER SENSOR IPR-BRK SCAN BD SPRING ETC-EXIT ELA HOU-CCD MODULE CBF SIGNAL-CCD FFC CBF HARNESS-SCAN MOTOR ELA HOU-OPE
SEC CODE
Refer to Info. Refer to Info. JC81-01688A JC81-00426A * * * * JC72-00809A JC72-00758A * JC74-00018A JC96-02706B 6602-001090 JB61-00059A JC39-00167A JC39-00030A * JC92-01381A JC96-02751A JB31-00011A * JC66-00531A 6044-000125 JC66-00530A JB72-00764A JB66-00083A JC63-00158A JC63-00157A JC70-00239A JC61-00703A JC72-00794A * JB72-00763A JB72-00764A 6044-000125 JC66-00532A JC72-00755A JC70-00228A * JC96-02759A JC39-00236A JB39-00077A
QTY
SA
REMARK
SCX-5315F SCX-5115
Samsung Electronics
5-7
SCX-5315F (OPE)
NO DESCRIPTION SEC CODE QTY SA REMARK
3 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-13 3-14 3-15 3-16 3-17 3-18 3-19 3-20 3-21
ELA HOU-OPE PMO-OPE COVER WINDOW-LCD (4IN1) PMO-COVER DUMMY OPE(M) PCT-ONETOUCH PAPER PCT-ONETOUCH CARD PMO-KEY ONETOUCH PMO-KEY SHIFT PMO-KEY FAX RMO-RUBBER ONETOUCH PMO-KEY SCROLL RMO-RUBBER SCROLL PMO-KEY COPY PMO-KEY TEL PMO-KEY OHD PMO-KEY SAVE(T) PMO-KEY SAVE PMO-KEY START PMO-KEY STOP RMO-RUBBER TEL PBA SUB-OPE(KOR) NPR-BADGE(45)
Refer to Info. Refer to Info. Refer to Info. Refer to Info. Refer to Info. JC72-00871A JC72-00860A JC72-00861A JC72-00862A JC73-00104A JC72-00866A JC73-00106A JC72-00863A JC72-00865A JC72-00864A JC72-00923A JC72-00867A JC72-00868A JC72-00869A JC73-00105A JC81-00779A *
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
O O O O O O O O O O O O O O O O O O O O O X
SCX-5315F
SCX-5115 (OPE)
NO DESCRIPTION SEC CODE QTY SA REMARK
3 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-13 3-14 3-15
ELA HOU-OPE(SEC) PMO-OPE COVER WINDOW-LCD(3IN1) PMO-COVER DUMMY OPE(C) PMO-KEY SCROLL PMO-KEY COPY PMO-KEY TEL PMO-KEY SAVE(T) PMO-KEY SAVE PMO-KEY STOP PMO-KEY START PMO-KEY OHD RMO-RUBBER SCROLL RMO-RUBBER TEL PBA SUB-OPE(KOR) NPR-BADGE(45)
Refer to Info. Refer to Info. Refer to Info. JC72-00859A JC72-00866A JC72-00863A JC72-00865A JC72-00923A JC72-00867A JC72-00869A JC72-00868A JC72-00864B JC73-00106A JC73-00105A JC81-00779A *
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
O O O O O O O O O O O O O O O X
SCX-5115
5-8
Samsung Electronics
7 8 0
Samsung Electronics
5 1 2-1 2 3-24 2-6 1-3 2-3 2-4 2-5 3-22 3-1 4-1 2-2 4-4 4-3 4-5 4-11 4-8 3-17 3-21 4-9 4-2 3-19 3-8 3-5 3-4 3-6 1-10 4 3-16 3-12 3-11 3-23 3-20 1-11 3-9 3-15 3-13 3-13 3-14 3-10 3 3-18 4-7 S1 4-6 S1 3-2 3-2 3-4 3-2 3-3 3-7 1-6
1-1
1-2
1-5
1-4
1-12
1-13
1-4
1-15
1-8 1-9
5-9
0 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 2 2-1 2-2 2-3 2-4 2-5 2-6 3 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-13 3-14 3-15
ELA HOU-ADF MEA UNIT-PLATEN COVER PMO-TX STACKER IPR-WASHER SPRING CU PMO-DOC GUIDE L PMO-DOC GUIDE R PMO-GEAR PINION MEA UNIT-HINGE RPR-ROLLER EXIT IDLE IPR-SHAFT EXIT NPR-SPRING PINCH DRIVE PMO-COVER PLATEN PPR-SPONG SHEET SHEET ABS-SHEET PLATEN(PET) IPR-SPRING PINCH ICT-SHAFT PINCH PMO-ROLL PINCH MEA UNIT-ADF UPPER ASSY PMO-COVER ADF UPPER RMO-ADF RUBBER PMO-HOLDER ADF RPR-SPONGE ADF SPRING ETC-COIL ADF SHEET-ADF ELA HOU-ADF LOWER ASSY SPRING ETC-TORSION DOC (CC2-F) RING-C GEAR-ADF 38 PMO-BUSH MEC-ROLLER DRIVER PMO-COVER ADF LOWER PMO-ACTUATOR SENSOR DOC PMO-ACTUATOR SENSOR REGI MEC-ROLLER EXIT PMO-BUSHING HOLDER SPRING ETC-CLUTCH GEAR-EXIT 23 SPRING ETC-WHITE BAR IPR-BRKT WHITE BAR PPR-WHITE BAR SHEET
JC96-02750A JC97-01722A JC72-00745A JF70-10616A JC72-00839B JC72-00838B JF72-41354A JC97-01731A JC73-00091A JC70-00242A JB71-00038A JC72-00738A JC72-00751A JC72-00750B JC70-00260A * JG72-40663A JC97-01581A JC72-00736A JB73-00052A JB72-00825A * JC61-00040A JC63-00079A JC81-00434A JB61-00076A * JB66-00103A JB72-00819A JC75-00149A JC72-00735A JB72-00837A JC72-00747A JC75-00150A JG72-40732A JC61-00062A JC66-00323A JC61-00548A JC70-00225A JC72-00752A
1 1 1 2 1 1 1 2 2 1 2 1 1 1 3 3 3 1 1 1 1 1 1 1 1 3 4 1 2 1 1 1 1 1 1 1 1 1 1 1
O O O O O O O O O O O O O O O X O O O O O X O O O O X O O O O O O O O O O O O O
5-10
Samsung Electronics
3-16 3-17 3-18 3-19 3-20 3-21 3-22 3-23 3-24 4 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 4-11 5 6 7 8 9
TAPE ETC-ANTI BRUSH PBA SUB-ADF PBA SUB-ADF POS SEN PBA SUB-ADF DET SEN CBF HARNESS-ADF ROLLER GND CBF HARNESS-DRIVER GND PMO-ACTUATOR SENSOR SCAN NPR-SPRING GND CBF D SUB CABLE-ADF_MAIN CABLE ELA HOU-ADF MOTOR ASSY GEAR-CLUTCH 29 IPR-BRKT ADF MOTOR PMO-WHITE CLUTCH SUB 29 GEAR-CLUTCH 39 GEAR-IDLE20/33 RING-C GEAR-IDLE17/35 GEAR-IDLE25 MOTOR STEP-ADF GEAR-JAM REMOVE GEAR-REDUCTION 45/19 MEA UNIT-PICKUP ASSY PMO-GUIDE PAPER PMO-COVER OPEN PMO-COVER SIDE L PMO-COVER SIDE R
* JC81-00437A JC92-01365A JC92-01366A JC39-00187A JB39-00065A * JC71-00031A JC39-00190A JC81-00435A * * * * * * * * JC31-00017A * * JC97-01582A JB72-00843A JC72-00737A JC72-00739A JC72-00740A
1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 7 2 1 1 1 1 1 2 1 1 1
X O O O O O X O O O X X X X X X X X O X X O O O O O
Samsung Electronics
5-11
1-6
1-2
S6
S6
1-1
6 19
7 12
10-4 10-6
10-5
10-1
10
5-12
Samsung Electronics
DESCRIPTION
ELA HOU-SIDE COVER MEA UNIT-DUPLEX ASSY PMO-GUIDE DP SIDE CBF HARNESS-SCAN GND SPRING ETC-FUSER EXIT GEAR-DUP IDLER 17 GEAR-MP/DUP DRV IPR-BRKT G DUP PMO-GP LOWER DP PMO-SHAFT DUP DRIVER PMO-ROLLER_EXIT RPR-RUBBER EXIT PMO-BUSHING TX(B4) IPR-PLATE SAW PMO-FEED FRAME PMO-HOLDER SAW IPR-BRACKET GUIDE A PMO-LOCKER SIDE R PMO-LOCKER OPEN SPRING ETC-LOCKER TORSION SPRING ETC-FEED MEA UNIT-TRAY PMO-TRAY CASE,MP PMO-TRAY EXT,MP PMO-SIDE GUIDE MP PMO-TRAY COVER,MP IPR-GUIDE LATCH PMO-TRAY LINK,MP LABEL(R)-HEIGHT,MP CBF HARNESS-OPE GND PMO-TIE STOPPER IPR-BRKT GROUND B IPR-BRKT GROUND TR IPR-BRKT GROUND A IPR-BRACKET GUIDE B PMO-BUSHING FEED RING-CS PMO-SIDE COVER ICT-SHAFT LOCKER
SEC CODE
JC96-02183B * JC72-00806A * JC61-70976A JC66-00341A JC66-00346A JC70-00233A JC72-00732A JC72-00764A * JC73-10203A JG72-40744A JC70-10232A JC72-00731A JC72-41213A JC70-00229A JC72-00763A JC72-00762B JC61-00479A JC61-00478A * JC72-00776A JC72-00778A JC72-00547G JC72-00777A JB70-10906A JC72-00857A JC68-00697A JC39-00036A JC72-00766A JC70-00230A JC70-00231A JC70-00232A JC70-00234A JC72-00730A 6044-000001 JC72-00765A JC70-00266A
QTY
1 1 1 1 2 3 1 1 1 2 2 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 2 1 1
SA
O X O X O O O O O O X O O O O O O O O O O X O O O O O O O O O O O O O O O O O
REMARK
Samsung Electronics
5-13
11
13
14
S6 S6 22 7
8 2 16 15 2
6 17 12 21 20 19 23 19 18 9 10
5-14
Samsung Electronics
DESCRIPTION
MEC-CASSETTE PLUS ASSY
SEC CODE
JC97-01736A JC70-00220A JC61-00831A JC70-00221A JC72-00795A * * JC72-00717A * JC72-41210A * JG61-70531A * * * * * JC70-00325A JC61-00653A * JC61-00548A JC61-00840A JC72-00877A
QTY
1 1 2 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 2 2 1 1 1
SA
O O O O O X X O X O X O X X X X X O O X O O O
REMARK
Samsung Electronics
5-15
21
7 21 8 10 6 21
5 4 5 4 10
10
19
20 22 S6 11 1
17 15 16 18 3 13 14
12
S6
5-16
Samsung Electronics
DESCRIPTION
MEA UNIT-EXIT ASSY PMO-GUIDE-EXIT UPPER PMO-GUIDE-EXIT LOWER PMO-GUIDE-JAM REMOVE MEC-ROLLER EXIT DRV PMO-ROLLER DECURL PMO-PULLEY DUPLEX BELT-TIMING GEAR GEAR-DUPLEX PMO-BEARING LARGE DP PMO-BEARING LARGE DP IPR-GROUND-EXIT ICT-SHAFT-EXIT LOWER ID PMO-ROLLER_EXIT SPRING ETC-EXIT ROLL FD HOLDER-EXIT(MC) PMO-ROLLER FD F PMO-ROLLER FD R SPRING ETC-EXIT LOWER IDLE MEC-BRUSH ANTISTATIC PBA SUB-BIN_FULL_SEN. RING-C PMO-LEVER-STACKING
SEC CODE
JC97-01643A JC72-00708A JC72-00710A * JC75-00127A JC72-00833A JC72-40980A 6602-001084 JC66-40912A JC72-00885A JC72-40978A * * * * * JC72-41007A JC72-41008A * JC75-00095A JC92-01400A * JC72-00709A
QTY
1 1 1 1 2 4 2 1 1 3 1 1 1 4 2 4 4 4 4 1 1 3 1
SA
O O O X O O O O O O O X X X X X O O X O O X O
REMARK
Samsung Electronics
5-17
17
1 5
4 7 3
20
S6 S6 11 19 10 21 9 13 12
12 5 8 15 17 19 14 21 18 12 S6
17 6
5-18
Samsung Electronics
DESCRIPTION
MEA-FEED ASSY PMO-FRAME FEED GEAR-FEED GEAR-MP/DUP DRV ICT-SHAFT FEED BEARING-PICKUP RING-E RING-CS PMO-BRKT FEED PMO-ROLLER FEED PMO-HOLDER PINCH C PMO-HOLDER PINCH SUB PMO-ROLLER FEED L SPRING-FEED CAST PMO-HOLDER PINCH M PMO-SUB HOLDER FEED SPRING-FEED MP WASHER-PLAIN PMO-ROLLER FEED S IPR-SHAFT FEED IDLER SHEET FEEDER E-RING
SEC CODE
JC75-00143B * JC66-00332A * * * * * * JC72-00727A * * JC72-40261A * * * * * * * * *
QTY
1 1 1 1 1 2 2 1 1 1 1 1 3 1 1 1 1 3 1 4 1 2
SA
O X O X X X X X X O X X O X X X X X X X X X
REMARK
Samsung Electronics
5-19
22
16 1 18 21 14 20 2 3 S9 4 2 8 6 20 9 5 10 S5 3
12 13 17 15 23 11 7
24
19
5-20
Samsung Electronics
DESCRIPTION
ELA HOU-MP ASSY A/S-PICK UP, MP AS(FRU) PMO-BUSHING PICKUP,MP RING-E SOLENOIDE,MP SPRING-CAM MP SPRING-PICK UP,MP SPRING-KNOCKUP,MP IPR-BRACKET SOLENOIDE PMO-HOLDER CAM MPF PMO-GEAR P/U MPF PMO-ROLLER CAM.MP PMO-ACTUATOR,MP PMO-ADJUSTER,MP PMO-CAM PICK UP,MP PMO-FRAME,MP PMO-HOLDER PAD,MP PMO-HOLDER SENSOR,MP PMO-HOUSING PICK UP,MP PMO-PLATE KNOCK UP,MP PMO-IDLE PICK UP,MP RPR-RUBBER PICK UP,MP RPR-RCT-PAD-PICKUP,MP RPR-PAD KNOCK UP,MP PBA SUB-MP SEN
SEC CODE
JC96-02182A JC81-00427A JC72-41364A 6044-000125 JC33-00006A JC61-00003A * JC61-00483A * * * * JC72-00767A JC72-00768A JC72-00769A JC72-00770A JC72-00771A JC72-00772A * * JC72-41027A * JC73-00090A JC73-10906A JC92-01362A
QTY
1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1
SA
O O O O O O X O X X X X O O O O O O X X O X O O O
REMARK
Samsung Electronics
5-21
1 20 17 1 8
16
14
19
2 9 15 11 6 1
10 5 7 3 1 4 18 11 1 5 12
13
5-22
Samsung Electronics
DESCRIPTION
ELA HOU-BASE FRAME ELA HOU-BASE FRAME SCREW-TAPTITE SCREW-TAPTITE SCREW-TAPTITE SPRING ETC-TORSION FOOT-ML80 CAM-CATCH IPR-CHANNEL BASE FRAME IPR-GROUND PLATE A(OPC) IPR-GROUND PLATE B(BASE) PMO-BASE FRAME PMO-BRACKET PUSH DEVE PMO-BRACKET SIDE OPEN PMO-COVER FRONT DUMMY ELA M/M-AUD SPEAKER SPRING ETC-DEVE REAR CBF HARNESS-OPC GND FAN-DC(LSU) SPRING ETC-DEVE FRONT SHEET-BASE FRAME SCREW-TAPPING
SEC CODE
JC96-02818A JC96-02818B * * * * JC61-40001A * * JC70-00240A JC70-00241A JC72-00779A * JC72-00781A JC72-00785A JC96-01607A * * JC31-00026A * * *
QTY
1 1 5 2 4 1 2 1 1 1 1 1 2 1 1 1 1 1 1 1 2 2
SA
O O X X X X O X X O O O X O O O X X O X X X
REMARK
SCX-5315F SCX-5115
Samsung Electronics
5-23
11
20
S 10 5 12 1 9 7
8 3
23 2 4 16 14 22 17 15 22 22 19 13 18 21 24
19
5-24
Samsung Electronics
DESCRIPTION
ELA HOU-PICKUP PLUS ASSY IPR-GND FEED IPR-GND INPUT IPR-GUIDE INPUT PMO-ACTUATOR NO PAPER PBA SUB-TONER_TX PBA SUB-PTL PMO-FEED SENSOR PMO-GUIDE PAPER PMO-HOLDER SENSOR FEED PMO-LENS TONER SENSOR PMO-PTL PATH PBA SUB-FEED+P.EMP SEN. PMO-BUSHING_P/U,MP HOUSING-PICKUP LARGE HOUSING-PICKUP SMALL RPR RUBBER PICKUP RUBBER PICKUP SMALL SHAFT-PICKUP CST SHAFT PIN ADF SHEET-PTL PATH SHAFT-SUB-PICKUP RING-E ID4 RING-E ID5 PMO-BEARING SHAFT SCREW-TAPTITE
SEC CODE
JC96-02715B * JC70-00235A JC70-00222A * JC92-01359A JC92-01361A * JC72-00722A * * * JC92-01363A JC72-41364A * * * JC73-00163A * * * * 6044-000125 6044-000231 JC72-41191A *
QTY
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 2 1 1
SA
O X O O X O O X O X X X O O X X X O X X X X O O O X
REMARK
Samsung Electronics
5-25
5 8 4
23
24 10 S10 1 2
23
11
S1 23 S10 12 3
13 14 23
S10
15 20 19 23 17 16 18
S10
22 17 23 21
23
5-26
Samsung Electronics
DESCRIPTION
ELA HOU-DRIVE(15PPM) IPR-BRKT MOTOR MOTOR STEP-MAIN CBF HARNESS-MOTOR RING-C SOLENOID-DUPLEX SPRING ETC-SOLENOID DP IPR-LINK SOLENOID GEAR-EXIT/U,ID GEAR-SWING DRV GEAR-35/19 GEAR-71/23 GEAR-DEVE DRV PMO-DEV/COUPLING GEAR-RDCN,OPC GEAR-86/23 GEAR-RDCN FEED OUTER GEAR-HUB CLUTCH GEAR-RDCN FEED INNER GEAR-FEED DRV GEAR-OPC DRV GEAR-GEAR FUSER DRV OUTER GEAR-FUSER DRV INNER RING-E MOTOR STEP-MAIN
SEC CODE
JC96-02741A * JC31-00020B JC39-00165A 6044-000159 JC33-00008A * * JC66-40211B * * * * * * * * * * * * * * 6044-000231 JC31-00028B
QTY
1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 7 1
SA
O X O O O O X X O X X X X X X X X X X X X X X O O
REMARK
M49SP-2K
M4PSP-2NK
Samsung Electronics
5-27
S5 23 12 27
19 S5 28 13 25 24
22 32 25 33 24 24 26 31 29.30 16 18 20 S4
10 8 7 6 21 15 S5 4 11
17
S5
5 3 2 4 1
5-28
Samsung Electronics
DESCRIPTION
ELA HOU-FRAME MAIN ASSY PMO-HOUSING TERMINAL IPR-TERMINAL BLADE IPR-TERMINAL SUPPLY IPR-TERMINAL TR IPR-TERMINAL GND IPR-TERMINAL DEVE KEY CBF-HARNESS-DEV-ID CBF-HARNESS-BLADE+SUPPLY+DEV CBF-HARNESS-THV WIRE CBF-HARNESS-MHV WIRE PMO-FRAME MAIN PMO-LENS TONER SENSOR IPR-GND EXIT IPR-GND OPC IPR-GND OPC BASE IPR-GND FUSER IPR-GUARD C/O S/W IPR-GND TERMINAL CBF HARNESS-AC WIRE AS-SWITCH MICRO(FRU) CBF-HARNESS-EARTH(TX MOTOR) PBA SUB-EXIT SENSOR PBA SUB-TONER_RX GEAR-EXIT/U,ID GEAR-EXIT,IDLE(Z17) CBF-HARNESS THERMISTOR_JOINT PMO-HOUSING TERMINAL IPR-TERMINAL FU PMO-CAP CONNECTOR L PMO-CAP CONNECTOR U ELA HOU-MOTOR GND SPRING-CLUTCH RING-CS
SEC CODE
JC96-02184A JC72-00802A * * JC70-00271A JC70-00272A * * * * * JC72-00800A JC72-00803A * * * * * * * JC81-00438A * JC92-01364A JC92-01360A JC66-40211B JC66-40964A JC39-00164A JC72-41010A JC70-10961A JC72-00463A JC72-00465A * JB61-70922A 6044-000001
QTY
1 1 2 2 1 1 2 1 5 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 3 2 1 1 2 1 1 1 2 5
SA
O O X X O O X X X X X O O X X X X X X X O X O O O O O O O O O X O O
REMARK
Samsung Electronics
5-29
S5 S5 13 S1 S1 10 12 11 S5
9 1
28
S5 6-1 6-2
6 7
S12
28
14
S5
20 16 21 25
26
S6
5-30
Samsung Electronics
DESCRIPTION
ELA HOU-FUSER ELA HOU-FUSER PMO-UPPER FUSER ROLLER-HEAT PMO-BEARING H/R-F BEARING-H/R L GEAR-FUSER GEAR-FUSER MEA UNIT-CLAW ASSY SPRING ETC-SAPERATION PMO-GUIDE CLAW PEX-ROLLER EXIT F_UP IPR-PIN ROLLER EXIT NPR-ELECTRODE GEAR NPR-ELECTRODE M NPR-ELECTRODE F THERMOSTAT THERMISTOR LAMP-HALOGEN LAMP-HALOGEN PMO-LOWER FUSER SPRING ETC-PR(7300) BEARING-PRESSURE/R ROLLER-PRESSURE PMO-LEVER JAM R PMO-LEVER JAM F PMO-GUIDE INPUT IPR-GROUND FU MEA UNIT-ACTUATOR ASSY PMO-ACTUATOR EXIT PMO-GUIDE DUPLEX PMO-ARM ACTUATOR GUIDE-REMOVE SPRING ETC-ACTUATOR6G LABEL(R)-CAU_HOT_FU LABEL(R)-HV FUSER LABEL FUSER M+ NUT-HEXAON
SEC CODE
JC96-02814A JC96-02815A JC72-00812A * JC72-00814A JC66-10902A JC66-40913B JC66-00669A JC97-01587A JC61-70909A * JC72-20901A * JC71-00029A JC71-00030A JC71-00028A 4712-000001 JC14-00001A 4713-001170 4713-001171 JC72-00820A JC61-00056A JC66-10901A * JC72-01262A JC72-01259A JC72-00817A JC70-00259A JC97-01611A JC72-00810A JC72-00816A JC72-00811A * JC61-00485A * * * *
QTY
1 1 1 1 1 1 1 1 4 1 1 2 2 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2
SA
O O O X O O O O O O X O X O O O O O O O O O O X O O O O O O O O X O X X X X
REMARK
110V 220V
110V
110V 220V
Samsung Electronics
5-31
5-14. Screw
NO
S1
SEC CODE
6006-000127
DESCRIPTION
SCREW-ASSY MACH
SPEC.
WS,PH,+,M3,L6,ZPC(YEL),MSWR15
S2
6001-000568
SCREW-MACHINE
PH,+,M3,L8,NI PLT,SM20C,-
S3
6002-000175
SCREW-TAPPING
PWH,+,2,M3,L8,ZPC(YEL),SM20C
S4
6002-000351
SCREW-TAPPING
PH,+,2,M2,L8,ZPC(YEL),SM20C
S5
6003-000119
SCREW-TAPTITE
BH,+,B,M3,L8,CBLACK,SWRCH18A
S6
6003-000196
SCREW-TAPTITE
PWH,+,B,M3,L10,NI PLT,SWRCH18A
S7
6003-000198
SCREW-TAPTITE
PWH,+,B,M3,L12,ZPC(YEL),SWRCH1
S8
6003-000221
SCREW-TAPTITE
PWH,+,S,M4,L8,ZPC(YEL),SWRCH18
S9
6003-000266
SCREW-TAPTITE
PWH,+,S,M3,L6,ZPC(YEL),SWRCH18
S10
6003-000269
SCREW-TAPTITE
BH,+,S,M3,L6,ZPC(YEL),SWRCH18A
S11
6003-001256
SCREW-TAPTITE
BH,+,B,M4,L10,NI PLT,SWRCH18A
S12
6006-001031
SCREW-ASSY MACH
WSP,PH,+,M3,ZPC(YEL),SM10C
5-32
Samsung Electronics
Block Diagrams
6. Block Diagrams
T M H V DEV SUPPLY BLADE
MAIN
LCD 1 6 x 2 line
H V
SPGPm
Backup logic ARM946ES
2 4P
SMPS / HVPS
+5V/+24V/+12V/+24Vs/Fuser
SRAM Flash,Kernel
(1MB) X 2EA
SDRAM,16MB
MOTOR DRIVER
A3977SLR
8P
MOTOR 1 MOTOR 2
PLATEN
15P D-SUB
D-SUB CONN.
Font ROM
24P
11P 2P 3P 3P 3P 4P
FLAT MOTOR
Option
2P
ADF
MOTOR DRIVER
ADF MOTOR PAPER SENSOR
POS,DET 3P x 2EA
74LCX245
2P x 3EA
74HCT273
3P x 2EA 6P x 1EA
CIP4
Image Processer
4P
PAPER SENSOR
FEED+P.EMP,EXIT,MP
FAST SRAM
(28Kbit)
Option
MODEM
33.6Kbps
4P
TRANSFORMER
600//600 Tx:Rx
LIU
LINE1
DMAC
LIN E IN T ERF A CE
Option
CCD MODULE External Auditron
EXTERNAL PHONE
Samsung Electronics
6-1
Connection Diagrams
7. Connection Diagrams
T H M H V DEV SUPPLY BLADE
L CD 20x 2line
SCA N
24P
OPE
MI COM - LCD Drive - Key Scan
5P
CN 4
24P
SMPS / HVPS
+5V/+24V/+12V/+24Vs /Fuser
CN5
CN 2 7
8P
CENTRONICS CABLE
36 P
CN12
Pl at en
15P D -SUB
11P 2P 3P
CN 2 CN 6
D-SUB CONN.
CN 7
OU T BIN F ULL
4P
C N8 CN9
FLAT MOTOR
HYPER
4P
MAIN PBA
3P
CN 26
CN 1 4
3P
Option
OPC
2P 4P
CN 1 9 CN 1 7 CN 2 6 CN 2 4
3P
CN 1 6 CN 1 1 CN 3
ADF
MOTOR DRIVER
DADF MOTOR
PAPER SENSOR
POS,DET
4P 2P
USB CABLE
24P
CN 18 CN 25 CN 13 CN 22 CN 20 CN 1 CN 2 3
4P
3P x 2EA
CCD MODULE
2P 2P 2P
3P
3P
6P 14P
TRANSFORMER
600/ / 600 Tx: R x
LI U
LINE1
L IN E
SOLENOID
PICK_ UP,DUPL EX,MP
IN T ERFAC E
EXTERNAL PHONE
Samsung Electronics
7-1
Connection Diagrams
Description
Description GND 24V 5V GND ADF_PHA GND SCAN_ADF_IA(1) SCAN_ADF_IA(0) SCAN_ADF_IB(0) ADF_PHB MODULE_DETECT SCAN_ADF_IB(1) ADF_P_POS ADF_P_DET NC ADF_P_REGI OPE_RXD OPE_RST OPE_TXD FLAT _COVER TM_A TM_NA TM_B TM_NB
Description GND 5V GND 5V GND 5V GND 12V GND 24V GND 24V GND 24V THV_PWM +24VS1 THV_EN +24VS1 THVREAD FUSER_ON MHV_PWM SPK+ DEV_PWM SPK-
Description NPC Description USB PORT Description PARALLEL PORT Description 24V DUPLEX_SOL Description DEV_ID GND GND Description NEW_OPC GND Description NC TONER_RX GND NC Description MODEM_RX GND MODEM_TXA1 MODEM_TXA2 12V REMOTE CML1 HOOK2* RIN G_DET* 5V DP GND RECALL E_DP*
Description
TONER_TX NC Description 5V FEED* GND 5V PEMPTY GND Description 5V PTL Description 24V MP_SOL Description 5V MP_EMPTY GND Description 5V 5VS 24V 24VS Description 24V MAIN_SOL Description 5V HYPER_TXD HYPER_RXD GND Description FEED MOTOR B FEED MOTOR A FEED MOTOR B* FEED MOTOR A* FUSER MOTOR A FUSER MOTOR B FUSER MOTOR B* FUSER MOTOR A*
TX
CON No. Pin No. 1 2 3 4 CN2 LSU 5 6 7 8 9 10 11 CON No. Pin No. 1 2 3 4 5 6 7 8 9 10 CN3 11 12 CCD 13 GND
Description HSYNC* 5VS GND LD_ON* VDO* NC LSU_CLK LREADY* PMOTOR GND 24VS1 Description SCAN CN4
5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
CON No. Pin No. 1 2 CN20 FEED/ 3 4 5 6 CON No. Pin No.
PEMPTY
1 2
CN21 PTL
1 2
MP_SOL
CCD_VOB GND CCD_VOR GND CCD_VOG GND GND CCD_PI_TG1 CCD_PI_TG1 CCD_PI_TG1 GND CCD_PI_RS CCD_PI2 CCD_PI1 GND GND CCD_PI_CP 5V GND CCD_HOME 24V INV_POWER GND
MP_EMP TY
Description THERM THERM Description 5V OUTBIN_FULL* GND Description 24V FAN Description 24V FAN LIU CN18 CON No. Pin No. 1 2
1 2
3 4 5 6 7 8 9 10 11
1 2
MODULE 14 15 16 17 18 19 20 21 22 23 24
2 3
12 13 14
7-2
Samsung Electronics
Connection Diagrams
Memo
Samsung Electronics
7-3
Repair Manual
Digital Laser MFP
SCX-5315F/SCX-5115
CONTENTS
1. Block Diagram 2. Connection Diagram 3. Circuit Description 4. Schematic Diagrams
This manual is made and described centering around circuit diagram and circuit description needed in the repair center in the form of appendix.
- This Service Manual is a property of Samsung Electronics Co.,Ltd. Any unauthorized use of Manual can be punished under applicable International and/or domestic law. -
Block Diagrams
1. Block Diagrams
T M H V DEV SUPPLY BLADE
MAIN
LCD 1 6 x 2 line
H V
SPGPm
Backup logic ARM946ES
2 4P
SMPS / HVPS
+5V/+24V/+12V/+24Vs/Fuser
SRAM Flash,Kernel
(1MB) X 2EA
SDRAM,16MB
MOTOR DRIVER
A3977SLR
8P
MOTOR 1 MOTOR 2
PLATEN
15P D-SUB
11P 2P 3P
D-SUB CONN.
24P
Option
SDRAM DIMM
3P 3P 4P
FLAT MOTOR
16MB
Option
2P
ADF
MOTOR DRIVER
ADF MOTOR PAPER SENSOR
POS,DET 3P x 2EA
74LCX245
2P x 3EA
74HCT273
3P x 2EA 6P x 1EA
CIP4
Image Processer
4P
PAPER SENSOR
FEED+P.EMP,EXIT,MP
FAST SRAM
(1Mb it)
Option
MODEM
33.6Kbps
4P
TRANSFORMER
600//600 Tx:Rx
LIU
LINE1
DMAC
LIN E IN T ERF A CE
Option
CCD MODULE External Auditron
EXTERNAL PHONE
Samsung Electronics
- This Document can not be used without Samsung's authorization -
1-1
Connection Diagrams
2. Connection Diagrams
T H M H V DEV SUPPLY BLADE
L CD 20x2line
SCA N
CN8
CN 2
2 4P
OPE
MI COM - LCD Drive - Key Scan
CN 1 6
SMPS / HVPS
+5V/+24V/+12V/+24Vs /Fuser
CN6
Network CARD
CN 1 4 CN 3 3 CN 4 CN 7 C N1 0 CN 1 1
1 0P 8P 11P 2P 3P 3P 3P
5P
CENTRONICS CABLE
SCF OU T BIN F ULL PC N T HYPER DEV CN T OPC
36 P
CN 3 1
Plat en
15P D -SUB
8P
CN 1 2 CN 1 9 CN 2 5
D-SUB CONN.
4P 2P
FLAT MOTOR
4P
MAIN PBA
CN 1 8
CN 1 9 CN 1 7
4P
Option
3P
CN 2 3 CN 2 1 CN 2 6 CN 2 9
2P 4P
TONER_T X
4P 2P
ADF
MOTOR DRIVER
DADF MOTOR
PAPER SENSOR
POS,DET
CN 1 3 CN 5
USB CABLE
2 2P
CN 1
CN 2 0 CN 2 7 CN 3 0
CN 28 CN 3
CN 2 2 CN 24
4P
10P 3P x 2EA
CCD MODULE
External Auditron
3P 2P 2P 2P
3P
6P 14P
TRANSFORMER
600/ / 600 Tx: R x
LI U
LINE1
LIN E
SOLENOID
PICK_ UP,DUPL EX,MP
IN T ERFAC E
EXTERNAL PHONE
Samsung Electronics
- This Document can not be used without Samsung's authorization -
2-1
Circuit Description
3. Circuit Description
3-1 Main PBA
3-1-1 Summary
The main circuit that consists of CPU, MFP controller (built-in 32bit RISC processor core: ARM946ES) including various I/O device drivers, system memory, scanner, printer, motor driver, PC I/F, and FAX transceiver controls the whole system. The entire structure of the main circuit is as follows :
T H
M H V
LCD 20x2line
SCAN
CN8
CN2
24P
CN6
OPE
MICOM - LCD Drive - Key Scan
CN 1 6
SMPS / HVPS
+5V/+24V/+12V/+24Vs/Fuser
Network CARD
CN 1 4
10P 8P 11P 2P 3P 3P 3P
5P
CENTRONICS CABLE
SCF OUT BIN FULL PCNT HYPER DEV CNT OPC
36P
CN 3 3 CN 4
CN 3 1
Platen
15P D-SUB
8P
CN 7
CN 1 2
D-SUB CONN.
4P 2P
C N1 0 CN 1 1
CN 1 9 CN 2 5
FLAT MOTOR
4P
MAIN PBA
CN 1 8
CN 1 9 CN 1 7
4P
Option
3P
CN 2 3
2P 4P
TONER_TX
4P 2P
CN 2 1
ADF
MOTOR DRIVER
DADF MOTOR
PAPER SENSOR
POS,DET
CN 1 3
USB CABLE
CN 2 6
22P
CN1
CN 5
CN 2 9
CN22
4P
10P 3P x 2EA
CCD MODULE
External Auditron
3P 2P 2P 2P
3P
6P 14P
TRANSFORMER
600/ / 600 Tx: Rx
LIU
LINE1
LINE
SOLENOID
PICK_UP,DUPLEX,MP
PAPER SENSOR
FEED+P.EMP,EXIT,MP
INT ERFACE
EXTERNAL PHONE
<Block Diagram>
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-1
Circuit Description
ARM946ES RISC PROCESSOR: drives PLL internally uses 120MHz and external Bus uses 60 MHz.
Fvd =((PAPER 1SCAN LINE sending time * SCAN effective late /1SCAN LINE DOT #)*4 =(600dpi*600dpi*58.208mm/s*216mm*4)/(25.4mm*25.4mm*76.1%)=28.697MHz PAPER 1SCAN LINE sending time=SCAN LINE interval/DOCUMENT SPEED (58.208mm/S) 1SCAN LINE DOT #=MAZ SCAN distance(216mm)*DOT# per 1mm
+3.3V Power Line (VCC) ARM946ES nRESET and 29LU16 POWER ON/OFF DETECT VCC RISING/FALLING 4.54.6V 1.48~1.52ms Td=(Ct*V sensing)/I charge (...Ct=33F, Is=100A)
2) TIMING CHART
MCLK nRESET 20 MCLK nPWRGD HICLK reRESETn 5.461 ms RESETn 15 HCLK (65535 MCLK) CLK falling 20 MCLK 5.461 ms (65535 MCLK)
3-2
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-3
Circuit Description
Pin No 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83
Pin Name nRD nROMCS0 nROMCS3 / nIOCS3 / GPO1 nWR nROMCS1 ADDR12 ADDR10 ADDR13 ADDR15 ADDR11 ADDR14 ADDR16 ADDR19 ADDR17 ADDR20 nIOCS0 ADDR21 nIOCS1 ADDR22 ADDR18 ADDR7 VDD_CORE nIOCS2 / nDACK0 / GPO2 ADDR1 ADDR8 ADDR9 ADDR4 ADDR6 ADDR2 ADDR3 ADDR5 VDD_ARM VDD_CORE EINT0 / TnRST EINT1 / TCK EINT2 / nRXD2 / TMS EINT3 / nTXD2 / GPO9 nRxD0 nRxD1 / GPI17 / TDI nTxD0 TESTMODE
Description ROM Bus Read_n ROM Bank0 Select_n ROM Bank3 Select_n / IO Bank3 Select_n / GPO[1] ROM Bus Write_n ROM Bank1 Select_n ROM Bus Addr[12] ROM Bus Addr[10] ROM Bus Addr[13] ROM Bus Addr[15] ROM Bus Addr[11] ROM Bus Addr[14] ROM Bus Addr[16] ROM Bus Addr[19] ROM Bus Addr[17] ROM Bus Addr[20] IO Bank0 Select_n ROM Bus Addr[21] IO Bank1 Select_n ROM Bus Addr[22] ROM Bus Addr[18] ROM Bus Addr[7] VDD for CORE (1.8V) IO Bank2 Select_n / DMA IO Bank0 ACK_n / GPO[2] ROM Bus Addr[1] ROM Bus Addr[8] ROM Bus Addr[9] ROM Bus Addr[4] ROM Bus Addr[6] ROM Bus Addr[2] ROM Bus Addr[3] ROM Bus Addr[5] VDD for ARM Hard Macro(1.8V) VDD for CORE (1.8V) Ext. Interrupt0 / TAP Controller Reset_n Ext. Interrupt1 / TAP Controller Clock Ext. Interrupt2 / UART RX DATA[2] / TAP Controller Mode Select Ext. Interrupt3 / UART TX Data[2] / GPO[9] UART RX Data[0] UART RX Data[1] / GPI[17] / TAP Controller Data In UART TX Data[0] TESTMODE (Nomal : 0)
PAD B4TR_TC B4TR_TC B4TR_TC B4TR_TC B4TR_TC B8TR_TC B8TR_TC B8TR_TC B8TR_TC B8TR_TC B8TR_TC B8TR_TC BD8TRP_TC BD8TRP_TC BD8TRP_TC B4TR_TC BD8TRP_TC B4TR_TC BD8TRP_TC BD8TRP_TC B8TR_TC B4TR_TC B8TR_TC B8TR_TC B8TR_TC B8TR_TC B8TR_TC B8TR_TC B8TR_TC B8TR_TC SCHMITT_FT SCHMITT_FT SCHMITT_FT BD4STRP_FT SCHMITT_FT SCHMITT_FT B4TR_TC SCHMITT_TC
Samsung Electronics
- This Document can not be used without Samsung's authorization -
Circuit Description
Ball No V10 Y10 Y11 W11 V11 U11 Y12 W12 V12 U12 Y13 W13 V13 Y14 W14 Y15 V14 W15 Y16 U14 V15 W16 Y17 V16 W17 Y18 U16 V17 W18 Y19 V18 W19 Y20 W20 V19 U19 U18 T17 V20 U20 T18 T19
Pin No 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125
Pin Name nTxD1 / GPO10 / TDO TESTSE VDD_CORE RXERR / GPI25 GND RX_DV / GPI20 RXD0 / GPI21 nLFPHB1 / nPRINT nLFPHB0 / nCMSG nLFPHA0 / CCLK RXD1 / GPI22 VDO SPD / nDREQ3 nWAIT1 / CRS COL / EINT4 TX_EN MDIO TXD3 / GPO14 TXD2 / GPO13 MDC / GPO15 TXCLK / GPI18 TXD1 / GPO12 PD4 TXD0 / nIOCS3 RXD3 / GPI24 PD2 PD6 RXD2 PWMOUT2 VCLK RXCLK / GPI19 PD1 nINIT VSS_ADC ATEST_OUT AIN2 AIN1 AIN0 VDD_ADC VDD_CORE GND VDD_CORE
Description UART Tx Data[1] / GPO[10] / Tap Controller Data Out TESTSE (Normal : 0) VDD for CORE (1.8V) MAC RX Error / GPI[25] GROUND_RING MAC RX Data Valid / GPI[20] MAC RX Data[0] / GPI[21] Motor Out B_n / Print Start_n Motor Out B / Command Message_n Motor Out A / Communication Clock MAC RX Data[1] / GPI[22] Video Data Out DIMM Detect / DMA REQ[3]_n Wait_n / MAC Carrier Sensor MAC Collision Detect / Ext. Interrupt4 MAC TX Enable MAC Management Data Inout MAC TX Data[3] / GPO[14] MAC TX Data[2] / GPO[13] MAC Management Data Clock / GPO[15] MAC TX Clock(25MHz) / GPI[18] MAC TX Data[1] / GPO[12] Parallel Port Data[4] MAC TX Data[0] / IO Bank3 Select_n MAC RX Data[3] / GPI[24] Parallel Port Data[2] Parallel Port Data[6] MAC RX Data[2] / GPI[23] PWM Output[2] Video Reference Clock MAC RX Clock(25MHz) / GPI[19] Parallel Port Data[1] Parallel Port Initialization_n VSS for ADC ADC Test Output ADC Channel2 Input ADC Channel1 Input ADC Channel0 Input Analog power for ADC (3.3V) VDD for CORE (1.8V) GROUND_RING VDD for CORE (1.8V)
PAD B4TR_TC SCHMITT_TC SCHMITT_TC SCHMITT_TC SCHMITT_TC B4TR_TC B4TR_TC B4TR_TC SCHMITT_TC B8TR_TC BD4SRTP_TC SCHMITT_TC SCHMITT_TC B4TR_TC BD4STRUQP_TC B4TR_TC B4TR_TC B4TR_TC SCHMITT_TC B4TR_TC BD4STRP_FT B4TR_TC SCHMITT_TC BD4STRP_FT BD4STRP_FT SCHMITT_TC B4TR_TC TLCHT_TC SCHMITT_TC BD4STRP_FT SCHMITT_FT ANA_TC ANA_TC ANA_TC ANA_TC -
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-5
Circuit Description
Ball No T20 R18 P17 R19 R20 P18 P19 P20 N18 N19 N20 M17 M18 M19 M20 L19 L18 L20 K20 K19 K18 K17 J20 J19 J18 J17 H20 H19 H18 G20 G19 F20 G18 F19 E20 G17 F18 E19
Pin No 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163
Pin Name VDD_CORE VBUS nLREADY / nEBSY nSELECTIN LSUCLK / nCBSY / GPO11 PD7 PWMOUT1 PWMOUT0 nEMSG / nDACK3 / PWMOUT3 nFSYNC / nLFPHA1 nHSYNC nSTROBE PD5 nWAIT0 / PDE nIOCS5 / nSCS4 / GPO3 / TONEOUT PD3 nFAULT nDREQ0 / GPI0 / ADDR23 nRESET PERROR nAUTOFD nDACK2 / DQM7 / GPO5 nDREQ2 / DQM6 / GPO6 nDREQ1 / DQM4 / GPO8 VDD_CORE nSCS0 nSCS2 nCAS nSCS1 nIOCS4 / nSCS3 / GPO4 BUSY PD0 SLCT_OUT nACK nDACK1 / DQM5 / GPO7 nRSTOUT / CLKOUT / GPO0 SA7 SA9
I/O I I I O I/O O O I/O I/O I I I/O I/O O I/O O I/O I O I O I/O I/O O O O O O O I/O O O O O O O
Description VDD for CORE (1.8V) USB Detect LSU Ready_n / Engine Busy_n Parallel Port Select Input_n LSU Clock / Command Busy_n / GPO[11] Parallel Port Data[7] PWM Output[1] PWM Output[0] Engine Message_n / DMA ACK[3]_n / PWM Output[3] Frame Sync_n / Motor Out A_n Line Sync_n Parallel Port Data Strobe_n Parallel Port Data[5] Wait_n / Parallel Port Data Enable DRAM Bank4 / IO Bank5 Select_n / GPO[3] / Tone Pulse Out Parallel Port Data[3] Parallel Port Fault_n DMA REQ[0]_n / GPI[0] / ADDR[23] External Reset_n Input Parallel Port Paper Error Parallel Port Auto Feed_n DMA ACK[2]_n / DQM[7] / GPO[5] DMA REQ[2]_n / DQM[6] / GPO[6] DMA REQ[1]_n / DQM[4] / GPO[8] VDD for CORE (1.8V) SDRAM Bank0 Select_n SDRAM Bank2 Select_n SDRAM Column Address Select_n SDRAM Bank1 Select_n IO Bank4 / SDRAM Bank3 Select_n / GPO[4] Parallel Port Busy Parallel Port Data[0] Parallel Port Selection Out Parallel Port Acknowledge_n DMA ACK[1]_n / DQM[5] / GPO[7] Internal Reset_n Out / Internal System Clock Out / GPO[0] SDRAM Bus Addr[7] SDRAM Bus Addr[9]
PAD SCHMITT_FT SCHMITT_FT SCHMITT_FT B4TR_TC BD4STRP_FT B4TR_TC B4TR_TC BD4STRP_FT BD4STRP_FT SCHMITT_FT SCHMITT_FT BD4STRP_FT BD4STRP_TC BD8TARP_TC BD4STRP_FT B4TR_TC BD4STRP_TC SCHMITT_TC B4TR_TC SCHMITT_FT BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC B4TR_TC BD4STRP_FT B4TR_TC B4TR_TC BD8TARP_TC B8TR_TC BD8TARP_TC BD8TARP_TC
3-6
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
Ball No D20 E18 D19 C20 E17 D18 C19 B20 C18 B19 A20 A19 B18 B17 C17 D16 A18 A17 C16 B16 A16 C15 D14 B15 A15 C14 B14 A14 C13 B13 A13 D12 C12 B12 A12 B11 C11 A11 A10 B10 C10 D10 A9 B9
Pin No 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207
Pin Name VDD_USB SA10 SA12 BA0 nRAS DQM2 DQM1 BA1 DQM0 DQM3 RREF VSSL VDDL VSSB DMNS DPLS VDD3_USB VSSC VDDC VDDB VDD_USB UCLK VSS_PLL2 VDD_PLL2 SA11 SA6 SA5 SA8 SA3 SA2 SA4 SA0 SA1 CKE nWE SD30 SD31 SD29 SD25 SD26 SD27 SD28 SD21 SD22
I/O O O O O O O O O O I/O I/O I/O I O O O O O O O O O O O I/O I/O I/O I/O I/O I/O I/O I/O I/O
Description VDD for USB Hard Macro (1.8V) SDRAM Bus Addr[10] SDRAM Bus Addr[120 SDRAM Bus Bank Select Addr[0] SDRAM Row Address Select_n SDRAM Bus DQM[2] SDRAM Bus DQM[1] SDRAM Bus Bank Select Addr[1] SDRAM Bus DQM[0] SDRAM Bus DQM[3] USB PHY Register Reference VSS for Deserialisation Flip ops VDD for Deserialisation Flip ops (1.8V) VSS for buffers USB2 DATAUSB2 DATA+ VDD for USB1.1 FS compliance (3.3V) VSS for DLL and Xor tree VDD for DLL and Xor tree (1.8V) VDD for buffers (1.8V) VDD for USB Hard Macro (1.8V) USB PLL Input Clock (12MHz) VSS for USB PLL VSS for USB PLL (1.8V) SDRAM Bus Addr[11] SDRAM Bus Addr[6] SDRAM Bus Addr[5] SDRAM Bus Addr[8] SDRAM Bus Addr[3] SDRAM Bus Addr[2] SDRAM Bus Addr[4] SDRAM Bus Addr[0] SDRAM Bus Addr[1] SDRAM Clock Enable SDRAM Write Enable_n SDRAM Bus Data[30] SDRAM Bus Data[31] SDRAM Bus Data[29] SDRAM Bus Data[25] SDRAM Bus Data[26] SDRAM Bus Data[27] SDRAM Bus Data[28] SDRAM Bus Data[21] SDRAM Bus Data[22]
PAD BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC ANA_FT ANA_FT ANA_FT TLCHT_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-7
Circuit Description
Ball No C9 D9 A8 B8 C8 A7 B7 A6 C7 B6 A5 D7 C6 B5 A4 C5 B4 A3 D5 C4 B3 B2 A2 C3
Pin No 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231
Pin Name SD23 SD24 SD18 SDCLK0 SD20 SD14 SD19 SD11 SD16 SDCLK1 SD12 SD17 SD13 SD8 SD5 SD9 SD6 SD3 SD10 SD7 SD4 SD1 SD0 SD2
I/O I/O I/O I/O O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
Description SDRAM Bus Data[23] SDRAM Bus Data[24] SDRAM Bus Data[18] SDRAM Clock Output0 SDRAM Bus Data[20] SDRAM Bus Data[14] SDRAM Bus Data[19] SDRAM Bus Data[11] SDRAM Bus Data[16] SDRAM Clock Output1 SDRAM Bus Data[12] SDRAM Bus Data[17] SDRAM Bus Data[13] SDRAM Bus Data[8] SDRAM Bus Data[5] SDRAM Bus Data[9] SDRAM Bus Data[6] SDRAM Bus Data[3] SDRAM Bus Data[10] SDRAM Bus Data[7] SDRAM Bus Data[4] SDRAM Bus Data[1] SDRAM Bus Data[0] SDRAM Bus Data[2]
PAD BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC BD8TARP_TC
3-8
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-9
Circuit Description
No 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88
Pin Name D30 D29 D28 GND20 D27 D26 D25 VDD11 D24 D23 D22 D21 GND6 D20 D19 D18 GND21 D17 D16 D15 D14 VDD3 D13 D12 D11 GND7 D10 D9 D8 D7 GND22 D6 D5 D4 VDD12 D3 D2 D1 D0 GND8 TX_EN1 TX_EN2 TX_A TX_B GND23
I/O B B B P B B B P B B B B P B B B P B B B B P B B B P B B B B P B B B P B B B B P O O O O P
Description CPU Data Bus [30] CPU Data Bus [29] CPU Data Bus [28] Vss Supply CPU Data Bus [27] CPU Data Bus [26] CPU Data Bus [25] Vdd Supply CPU Data Bus [24] CPU Data Bus [23] CPU Data Bus [22] CPU Data Bus [21] Vss Supply CPU Data Bus [20] CPU Data Bus [19] CPU Data Bus [18] Vss Supply CPU Data Bus [17] CPU Data Bus [16] CPU Data Bus [15] CPU Data Bus [14] Vdd Supply CPU Data Bus [13] CPU Data Bus [12] CPU Data Bus [11] Vss Supply CPU Data Bus [10] CPU Data Bus [9] CPU Data Bus [8] CPU Data Bus [7] Vss Supply CPU Data Bus [6] CPU Data Bus [5] CPU Data Bus [4] Vdd Supply CPU Data Bus [3] CPU Data Bus [2] CPU Data Bus [1] CPU Data Bus [0] Vss Supply Motor Control Tx Enable 1 Motor Control Tx Enable 2 Motor Control Tx Channel A Motor Control Tx Channel B Vss Supply
Pad Type phbst8 phbst8 phbst8 vss3op phbst8 phbst8 phbst8 vdd3op phbst8 phbst8 phbst8 phbst8 vss2i phbst8 phbst8 phbst8 vss3op phbst8 phbst8 phbst8 phbst8 vdd2i phbst8 phbst8 phbst8 vss2i phbst8 phbst8 phbst8 phbst8 vss3op phbst8 phbst8 phbst8 vdd3op phbst8 phbst8 phbst8 phbst8 vss2i phob4 phob4 phob4 phob4 vss3op
Current drive 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 4mA 4mA 4mA 4mA -
3-10
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
No 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133
Pin Name nTX_A nTX_B MOTOR_POL VDD4 PItg1 PI1 PI2 GND9 PIrs PIcp ADC_CLK VDD13 CDS2_CLK SCLK1 SLOAD1 VDD10 SDO1 SDIO1 SDIO2 GND10 AFE_D9 AFE_D8 AFE_D7 AFE_D6 VDD5 AFE_D5 AFE_D4 AFE_D3 GND25 AFE_D2 AFE_D1 AFE_D0 GND11 SRAM_A15 SRAM_A14 SRAM_A13 SRAM_A12 VDD14 SRAM_A11 SRAM_A10 SRAM_A9 GND26 SRAM_A8 SRAM_A7 SRAM_A6
I/O O O I P O O O P O O O P O O O P O B B P I I I I P I I I P I I I P O O O O P O O O P O O O
Description Motor Control Tx Channel A Motor Control Tx Channel A Motor Polarity Vdd Supply CIS/CCD PItg1 Signal CIS/CCD PI1 Signal CIS/CCD PI2 Signal Vss Supply CIS/CCD PIrs Signal CIS/CCD PIsh Signal AFE ADC Clock Vdd Supply AFE CDS2 Clock AFE SIO Sync. Clock AFE SIO Read/Write Control Signal Vdd Supply AFE SIO Serial Output 1 AFE SIO Serial Inout/Output 1 AFE SIO Serial Inout/Output 2 Vss Supply A/D Converted Data Bus [9] A/D Converted Data Bus [8] A/D Converted Data Bus [7] A/D Converted Data Bus [6] Vdd Supply A/D Converted Data Bus [5] A/D Converted Data Bus [4] A/D Converted Data Bus [3] Vss Supply A/D Converted Data Bus [2] A/D Converted Data Bus [1] A/D Converted Data Bus [0] Vss Supply SRAM Address Bus [15] SRAM Address Bus [14] SRAM Address Bus [13] SRAM Address Bus [12] Vdd Supply SRAM Address Bus [11] SRAM Address Bus [10] SRAM Address Bus [9] Vss Supply SRAM Address Bus [9] SRAM Address Bus [9] SRAM Address Bus [9]
Pad Type phob4 phob4 ptis vdd2i phob8 phob8 phob8 vss2i phob8 phob8 phob8 vdd3op phob8 phob8 phob8 vdd3op phob8 phbst8 phbst8 vss2i ptis ptis ptis ptis vdd2i ptis ptis ptis vss3op ptis ptis ptis vss2i phob8 phob8 phob8 phob8 vdd3op phob8 phob8 phob8 vss3op phob8 phob8 phob8
Current drive 4mA 4mA 4mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-11
Circuit Description
No 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 3-12
Pin Name SRAM_A5 GND12 SRAM_A4 SRAM_A3 SRAM_A2 SRAM_A1 VDD6 SRAM_A0 SRAM_nWR SRAM_D15 SRAM_D14 GND27 SRAM_D13 SRAM_D12 SRAM_D11 GND13 SRAM_D10 SRAM_D9 SRAM_D8 SRAM_D7 VDD15 SRAM_D6 SRAM_D5 SRAM_D4 GND28 SRAM_D3 SRAM_D2 SRAM_D1 SRAM_D0 GND14 GPO7/PItg2 GPO6/RLED GPO5/GLED GPO4/BLED VDD7 GPO3/PItg3 GPO2/PIsh GPO1/ LEVEL_SHIFT GPO0 GND29 GPIO2B/AFE_D11 GPIO2A/AFE_D10 GPIO29/AFE_D9 GND30 GPIO28/AFE_D8
I/O O P O O O O P O O B B P B B B P B B B B P B B B P B B B B P O O O O P O O O O P B B B P B
Description SRAM Address Bus [9] Vss Supply SRAM Address Bus [9] SRAM Address Bus [9] SRAM Address Bus [9] SRAM Address Bus [9] Vdd Supply SRAM Address Bus [9] SRAM Write Enable Signal SRAM Data Bus [15] SRAM Data Bus [14] Vss Supply SRAM Data Bus [13] SRAM Data Bus [12] SRAM Data Bus [11] Vss Supply SRAM Data Bus [10] SRAM Data Bus [9] SRAM Data Bus [8] SRAM Data Bus [7] Vdd Supply SRAM Data Bus [6] SRAM Data Bus [5] SRAM Data Bus [4] Vss Supply SRAM Data Bus [3] SRAM Data Bus [2] SRAM Data Bus [1] SRAM Data Bus [0] Vss Supply General Purpose Output [7] General Purpose Output [6] General Purpose Output [5] General Purpose Output [4] Vdd Supply General Purpose Output [3] General Purpose Output [2] General Purpose Output [1] General Purpose Output [0] Vss Supply General Purpose Input/Output 2 [11] General Purpose Input/Output 2 [10] General Purpose Input/Output 2 [9] Vss Supply General Purpose Input/Output 2 [8]
Pad Type phob8 vss2i phob8 phob8 phob8 phob8 vdd2i phob8 phob8 phbst8 phbst8 vss3op phbst8 phbst8 phbst8 vss2i phbst8 phbst8 phbst8 phbst8 vdd3op phbst8 phbst8 phbst8 vss3op phbst8 phbst8 phbst8 phbst8 vss2i phob8 phob8 phob8 phob8 vdd2i phob8 phob8 phob8 phob8 vss3op phbst8 phbst8 phbst8 vss3op phbst8
Current drive 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA
Samsung Electronics
- This Document can not be used without Samsung's authorization -
Circuit Description
No 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208
Pin Name GPIO27/AFE_D7 GPIO26/AFE_D6 GPIO25/AFE_D5 VDD16 GPIO24/AFE_D4 GPIO23/AFE_D3 GPIO22/AFE_D2 GND15 GPIO21/AFE_D1 GPIO20/AFE_D0 GPIO1F/ SRAM_D15 GPIO1E/ SRAM_D14 GND31 GPIO1D/ SRAM_D13 GPIO1C/ SRAM_D12 GPIO1B/ SRAM_D11 GPIO1A/ SRAM_D10 VDD17 GPIO19/SRAM_D9 GPIO18/SRAM_D8 GPIO17/SRAM_D7 GND32 GPIO16/SRAM_D6 GPIO15/SRAM_D5 GPIO14/SRAM_D4 GPIO13/SRAM_D3 GND18 GPIO12/SRAM_D2 GPIO11/SRAM_D1 GPIO10/SRAM_D0
I/O B B B P B B B P B B B B P B B B B P B B B P B B B B P B B B
Description General Purpose Input/Output 2 [7] General Purpose Input/Output 2 [6] General Purpose Input/Output 2 [5] Vdd Supply General Purpose Input/Output 2 [4] General Purpose Input/Output 2 [3] General Purpose Input/Output 2 [2] Vss Supply General Purpose Input/Output 2 [1] General Purpose Input/Output 2 [0] General Purpose Input/Output 1 [15] General Purpose Input/Output 1 [14] Vss Supply General Purpose Input/Output 1 [13] General Purpose Input/Output 1 [12] General Purpose Input/Output 1 [11] General Purpose Input/Output 1 [10] Vdd Supply General Purpose Input/Output 1 [9] General Purpose Input/Output 1 [8] General Purpose Input/Output 1 [7] Vss Supply General Purpose Input/Output 1 [6] General Purpose Input/Output 1 [5 General Purpose Input/Output 1 [4] General Purpose Input/Output 1 [3] Vss Supply General Purpose Input/Output 1 [2] General Purpose Input/Output 1 [1] General Purpose Input/Output 1 [0]
Pad Type phbst8 phbst8 phbst8 vdd3op phbst8 phbst8 phbst8 vss2i phbst8 phbst8 phbst8 phbst8 vss3op phbst8 phbst8 phbst8 phbst8 vdd3op phbst8 phbst8 phbst8 vss3op phbst8 phbst8 phbst8 phbst8 vss3op phbst8 phbst8 phbst8
Current drive 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 8mA 4mA -
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-13
Circuit Description
3) OPERATING PRINCIPLE When the RCSO(ROM CHIP SELECT)signal is activated from the CPU after the POWER is ON, it activates RD SIGNAL and reads the DATA(HIGH/LOW) stored in the FLASH MEMORY to control the overall system. The FLASH MEMORY may also write. When turning the power on, press and hold the key(power switch) for 2 - 3 seconds, then the LED will scroll and the PROGRAM DOWNLOAD MODE will be activated. In this mode, you can download the program through the parallel port.
AC CHARACTERISTICS
Program Command Sequence (last two cycles) tAS tWC
Addresses
555h
P A
P A
P A
tAH
CE# OE#
tWP
tCH
tWHWH1
WE#
tCS
tWPH
tDS
tDH PD
tBUSY
Data
A0h
Status
DOUT
tRB
RY/BY#
tVCS
VCC
Notes: 1. PA = program address, PD = program data, DOUT is the true data at the program address. 2. Illustration shows device in word mode.
Figure 17.
BYTE
tSET (tAS)
tHOLD (tAH)
Note: Refer to the Erase/Program Operations table for tAS and tAH specifications.
Figure 16.
3-14
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
2) OPERATING PRINCIPLE DRAM can either read or write. The data can be stored in the DRAM only when the power is on. It stores data white the CPU processes data. The address to read and write the data is specied by RAS SIGNAL and CAS SIGNAL. DRAMWE*SIGNAL is activated when writing data and DRAMOE*SIGNAL, when reading. You can expand up to 64MBYTE of DRAM in this system. Start Address ~ End Address 0x00000000 ~ 0x00FFFFFF 0x01000000 ~ 0x01FFFFFF 0x02000000 ~ 0x02FFFFFF 0x03000000 ~ 0x03FFFFFF 0x04000000 ~ 0x0FFFFFFF 0x10000000 ~ 0x1FFFFFFF 0x20000000 ~ 0x20FFFFFF 0x21000000 ~ 0x21FFFFFF 0x22000000 ~ 0x22FFFFFF 0x23000000 ~ 0x23FFFFFF 0x24000000 ~ 0x24FFFFFF 0x25000000 ~ 0x25FFFFFF 0x26000000 ~ 0x26FFFFFF 0x27000000 ~ 0x27FFFFFF 0x28000000 ~ 0x28FFFFFF 0x29800000 ~ 0x29FFFFFF 0x2A000000 ~ 0x2FFFFFFF 0x30000000 ~ 0x30FFFFFF 0x31000000 ~ 0x31FFFFFF 0x32000000 ~ 0x32FFFFFF 0x33000000 ~ 0x37FFFFFF 0x38000000 ~ 0x38FFFFFF 0x39000000 ~ 0x390003FF 0x38000500 ~ 0x3FFFFFFF 0x40000000 ~ 0x4FFFFFFF 0x50000000 ~ 0x5FFFFFFF 0x60000000 ~ 0x6FFFFFFF 0x70000000 ~ 0x7FFFFFFF 0x80000000 ~ 0xBFFFFFFF 0xC0000000 ~ 0xC00007FF 0xC0000800 ~ 0xC0FFFFFF Samsung Electronics
- This Document can not be used without Samsung's authorization -
Contents ROM Bank0 ROM Bank1 ROM Bank2 ROM Bank3 Unused Special Function Registers I/O Bank0 I/O Bank1 I/O Bank2 I/O Bank3 I/O Bank4 I/O Bank5 DMA I/O Bank0 DMA I/O Bank1 DMA I/O Bank2 DMA I/O Bank3 Unused RSH SRAM HPVC SRAM MOTOR SRAM Unused USB CSR & FIFO USB PLUG DETECT Unused SDRAM array0 (bank 0) SDRAM array1 (bank 1) SDRAM array2 (bank 2) SDRAM array3 (bank 3) SDRAM array0~4 (Mirror) MAC Unused
3-15
Circuit Description
0 CLOCK CKE
*Note 1
10
11
12
13
14
15
16
17
18
19
HIGH
CS RAS
*Note 2
BA1
A10/AP
RAa
RBb
RCc
RDd
CL=2 DQ CL=3
WE DQM
Read (C-Bank)
Precharge (D-Bank)
: Dont care
* Note : 1. CS can be dont cared when RAS, CAS and WE are hih at the clock high going dege. 2. To interrupt a burst read by row precharge, both the read and the precharge banks must be the same.
3-16
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
10 HIGH
11
12
13
14
15
16
17
18
19
RAa
RBb CAa
CBb RCc
RDd CCc
CDd
*Note 2
A10/AP DQ WE
RAa
RBb
RCc
RDd
DAa0 DAa1 DAa2 DAa3 DBb0 DBb1 DBb2 DBb3 DCc0 DCc1 DDd0 DDd1 DDd2
tCDL
tRDL
*Note 1
DQM
Write (D-Bank)
: Don't care
*Note : 1. To interrupt burst write by Row precharge, DQM should be asserted to mask invalid input data. 2. To interrupt burst wrige by Row precharge, both the write and the prechargebanks must be the same.
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-17
Circuit Description
3-18
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
3-3 Scanner
3-3-1 SUMMARY
This at-bed type device to read manuscripts has 600dpi CCD as an image sensor. There is one optical sensor for detecting CCD home position and Scan-end position. The home position is detected by a optical sensor which is attached to the CCD Module. The Scan-end position is calculated by numer of motor step.
CCD
Charge Coupled Device improves productivity and allows a compact design. This machine uses a color CCD. Minimum Scan Line Time for One Color : 2.5mSec Light Source Power : +18V Maximum Pixel frequency : 10MHz Effective Sensor Element : 5340 X 3 Clamp Level : 0.7~ 0.8V Bright Output : MIN 0.8V
EXT SRAM
Imag e SRAM 8 192 x 8 ( 2l ine) Processing Enlarge men t / Redu ction Mo dule
SRAM 256 x 8
SRAM
4 09 6 x16
(2 line )
IRQ
Interrupt Contro l
Vp eak Contro l
Mo to r Con tro l D MA
TX_A, B n TX_A, B
TX_EN1, EN2
CIP4 Register
Interface
SRAM 1 024 x 8
n CS
n RD
n WR
A [ 5 : 0]
D [ 15 : 0]
n XDREQ
n XDACK
<Block Diagram>
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-19
Circuit Description
Shading Correction
(1) White shading correction support for each R/G/B (2) White shading data memory : 3x8Kx12bits = 288Kbits (3) Black shading data memory : 3x8Kx12bits = 288Kbits 384Kbits (external) 384Kbits (external)
Gamma Correction
(1) Independent Gamma table for each RGB component (2) Gamma table data memory : 3x1Kx8bits = 24Kbits (internal)
Binarization (mono)
(1) 256 Grays halftone representation for Photo document : 3x5 EDF(Error DifFusion) method proposed by Stucki. (2) LAT(Local Adaptive Thresholding) for Text document : use of 5x5 LOCAL WINDOW (TIP ALGORITHM) ABC(Automatic Background Control) :Tmin Automatic change (3) Mixed mode processing for text/photo mixed document (4) EDF data memory : 2x4Kx16bits = 128Kbits (internal) (5) LAT data memory : 4x4Kx16bits = 256Kbits (external)
3-20
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
Auto-Run
Automatic CLK_LINE (line processing start control) and TG (line scan start control) signal generation| (1)Available resynchronization of TG signal (2) programmable TGs period & CLK_LINEs occurrence number
36 General Purpose Input/Output : 8(GPO), 28(GPIO) Black/White reversion, and Image Mirroring support
ADD R BU S
DATA MEMORY
DATA BUS
1M bit SRAM
T R D M A A C K
T R D M A R E Q
Image Processor
CPU SPGPm
Scan/Motor Driver
AFE
12b it ADC
12 b it (R/ G/ B) ADD R- BUS ADDR- BUS PI_TG PI1 , PI2 DAT A- BUS DAT A- BUS Tx_A, Tx_B, n Tx_A, nTx_B Ana lo g Si gn al
Scanner
CIP4
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-21
Circuit Description
EXT SRAM
Vertical Decimation
Imag e SRAM 8 192 x8 ( 2l ine) Processing Enlarge men t / Redu ction Mo dule
SRAM 256 x 8
SRAM
4096 x16
(2 line )
IRQ
Interrupt Contro l
Vp eak Contro l
TX_A, B nTX_A, B
TX_EN1, EN2
CIP4 Register
Interface
SRAM 1 024 x 8
nCS
nRD nWR
A [5:0]
D [15:0]
nXDREQ
nXDACK
3-22
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
PPD( 7: 0)
DATA
BUSY
nSTROBE
nACK
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-23
Circuit Description
1 nSTROBE
BUSY
PPD( 7: 0)
BYTE0
BYTE1
nAUTOFD
DATA BYTE
COMMAND BYTE
1. The host places data on the data lines and indicates a data cycle by setting nAUTOFD 2. Host asserts nSTROBE low to indicate valid data 3. Peripheral acknowledhes host by setting BUSY high 4. Host sets nSTROBE high. This is the edge that should be used to clock the data into the Peripheral 5. Peripheral sets BUSY low to indicate that it is ready for the next byte 6. The cycle repeats, but this time it is a command cycle because nAUTOFD is low
1 2 nACK
5 6
nAUTOFD
PPD( 7: 0)
BYTE0
BYTE1
BUSY
DATA BYTE
C M OM AND BYTE
nINI T
PE
1. The host request a reverse channel transfer by setting nINIT low 2. The peripheral signals that it is OK to proceed by setting PE low 3. The peripheral places data on the data lines and indicates a data cycle by setting BUSY high 4. Peripheral asserts nACK low to indicate valid data 5. Host acknow ledges by setting nAUTOFD high 6. Peipheral sets nACK high. This is the edge that should be used to clock the data into the host 7. Host sets nAUTOFD low to indicate that it is ready for the next byte 8. The cycle repeats, but this time it is a command cycle because BUSY is low
3-24
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
Microcontroller Interface
48 MHz Oscillator
XIN XOUT
RX TX
Clock Generator
CLKOUT
SIE Media Access Controller[MAC] Physical Layer interface[PHY] Clock Recovery USB Event Detect V3.3 Trans ceiver VReg AGND
D+
D-
Upstream Port
3-4-2-1 Features
Full-Speed USB Node Device USB transceiver 3.3V signal voltage regulator 48 MHz oscillator circuit Programmable clock generator Serial Interface Engine consisting of Physical Layer In-terface (PHY) and Media Access Controller (MAC), USB Specication 1.0 compliant Control/Status Register File USB Function Controller with seven FIFO-based End-points : One bidirectional Control Endpoint 0 (8bytes) - Three Transmit Endpoints (2*32 and 1*64 bytes) Three Receive Endpoints (2*32 and 1*64 bytes) 8-bit parallel interface with two selectable modes : - non-multoplexed multiplexed (Intel compatible) DMA support for parallel interface MICROWIRE/PLUS Interface 28-pin SO package
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-25
Circuit Description
CS A0 VVR RD
DATA_IN DATA_IN
0x00
DATA_OUT DATA_OUT
D[7:0] ADDR ADDRESS 0x3F REGISTERFILE <Non-Multiplexed Mode Interface Block Diagram>
cs
A0 RD
VVR
D[7:0]
input
out
out
vvrte Address
Read Data
3-26
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-27
Circuit Description
3-28
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
LSU MHV
SUPPLY ROLLER
THV
PRESSURE ROLLER
TRANSFER ROLLER
First, in the electrication process, retain constant charge at approx. -900V for the electric potential on the OPC surface by electrifying OPC drum at approx. -1.4KV through the electrication roller. The electried surface of OPC is exposed responding to the video data by the LSU that received print command due to rotation. The unexposed non-video section will retain the original electric potential of -900V, but the electric potential of the image area exposed by LSU will be approx. -180V that it will form the electrostatic latent image. The surface of the photo-conductive drum where the electrostatic latent image is formed reaches the developer as the drum rotates. Then the electrostatic latent image formed on the OPC drum is developed by the toner supplied to the developing roller by supplying roller and it is transformed into visible image. It is the process to change the afterimage on the OPC drum surface formed by LSU into visible image by the toner particles. While the supply roller energized with -450V by HVPS and the developer roller energized with -300V rotate in the same direction, it keeps the toner particles between two rollers supplied to OPC drum in negative state by the friction between two rollers. The toner supplied to the developer roller is biased to bias electric potential by the developer roller and transferred to the developing area. After (-) toner is attached to the developer roller, it will move to the exposed high electric potential surface (-180V) rather than to the unexposed low electric potential surface (-900V) of the developer roller and OPC drum. Eventually the toner will not settle in the low electric potential surface to form the visible image. Later, the OPC drum continues to rotate and reaches to transfer location in order to accomplish the transfer process. This process transfers the (-)toner on the transfer roller to the printing paper by the transfer roller. The ()toner attached to the OPC drum will be energized to hundreds to thousands of the (+)transfer voltage by HVPS. The (+)electrostatic force of the transfer roller generated has higher adhesiveness than the (-)toner OPC drum and thus it moves to the surface of the paper passing through the transfer roller. The toner transferred to the paper with weak electrostatic force is xed to the paper by the pressure and heat of the xer composed of pressure roller and heat roller. The toner attached to the paper is melted by applying the heat (approx. 180C) from the heat roller and the pressure (approx. 4kg) from the pressure roller. After the xing process, the paper is sent out of the set to nish the printing process.
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-29
Circuit Description
TRANS
REGULATION CIRCUIT
OUTPUT CIRCUIT
MHV
MHV-PWM
<Electrication Unit Block-Diagram>
THVPWM
PWM CONTROL UNIT SWITCHING CONTROL UNIT TRANS REGULATION CIRCUIT
THV
FE E DBACK
THVEA
TRANS
REGULATION CIRCUIT
THVREAD
THV ENVIRONMENT RECOGNITION CIRCUIT FEED BACK
3-30
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
MHV-PWM
PWM CONTROL UNIT
TRANS
REGULATION CIRCUIT
MHV
OPC
FEEDBACK
BIAS-PWM BLADE
PWM CONTROL UNIT SWITCHING CONTROL UNIT TRANS REGULATION CIRCUIT
SUPPLY
FEEDBACK
DEV
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-31
Circuit Description
D402 4KV U103 7407 R412 2.2K Q401 A708 R405 220K 24VS Q402 D526
MHV-PWM
R408 47K
R409 390
R406 2.2K
D502 4KV
7
R501 100
Q501 A708-Y
R506 86.6KF
ZD501 100V
_ U1 + U101-B KA324
U103-A R519 7407 2.2K R503 100KF R502 2K C501 R504 56.6KF 104 C502 222 R507 12KF
ZD501 100V
3-32
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
5V 18V R201 10K #7 TEV-PWM 1 U2 2 3 U2 R206 100 Q203 A708Y R208 30K R209 100KF VR201 50K + C101 35V47UF R212 680K C203 472 D203 1N4148 ZD201 ZD202 5.65V 705V R214 2.2K C204 333Z R215 390 C201 103 C202 121 R210 845KF D202 1N4148 R211 1MF 24VS T201 KAB-007 1 R205 1.8K D201 1N4148 5 + U1 6 _ 11 KA324 7 R213 2.2K Q204 D526 5 2 7 C205 2KV68pF D204 6KV C206 6KV470pF C208 6KV D206 6KV C209 6KV
D205 6KV
D207 6KV
6 C207 3KV470pF
24VS
R207 2K
R216 SBR306
R218 MGR1/2W100KF
R217 SBR207
#17 #19
5V
5V
D301 1N4148
18V
R309 202K #5 TEV-EA 5 7 6 U2 7407 R307 33K 18V D-GND C4 103 R310 2.2K R308 33K R302 33K R303 100KF C302 102 D302 1N4148 C303 103 R304 389KF R306 26.1KF Q302 A708Y Q301 A708Y
R312 1W56
KAB-006 T301 1 6
C307 3KW470pF
D304 4KV
24VS
R313 1W56
D303 4KV
C308 3KV470pF
R315 SBR306
#24
TEV-READ
+ 10 U1 _ 9
KA324
R301 470K
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-33
Circuit Description
3-34
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
UART
Connector
11
LCD 16 2line
Reset
MICOM HT48R50
7 X Y 8
Key Matrix
LEDs
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-35
Circuit Description
*DP DIAL Controls from MAIN through / DP-Terminal. for U.S.Usage, set time to DF signal of 40:60 M/B. DP signal is made of U6 (pcb817). The DC current which ows thru Q2 Base is regulated by On/Off switch and turns to DP dial signal with a COUPLER. CTR 21 does not have telephone capability but has the number 3 and 4 Line Connection. No DP condition but possibility to get approval only on DTMF Dial based terminal.
Samsung Electronics
Circuit Description
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-37
Circuit Description
L1
C18
SY1
R66
1 6 CON502
R23
PC3
3-38
- This Document can not be used without Samsung's authorization -
Samsung Electronics
Circuit Description
3-8-4-2. The Concept of Fixed Lamp Control For xed lamp control, the logic unit "fuser on" control signal and SMPS unit DC power must be supplied. This circuit turns on only when "fuser on" sends the signal and the DC power is supplied. The following explains how the xed lamp control circuit works. logic unit "fuser on" sends trigger current to triac driver PC3 LED, then the infrared ray is detected by PC3 photo detector. Next, YC3 triac is conducted. The conducted current sends trigger input to triac SY1 gate. At this point, SY1 is conducted and AC power is supplied to xed lamp. Lamp is turned on and temperature rises. As this xed lamp control circuit uses the AC voltage ("+" and "-" are repeated) as the power supply, it used two-way triac (SY1), which has advantage over one-way SCR considering the price, size and reliability. Triac's gate can be triggered by either forward or reverse signal. Once triac is turned on, it will not be controlled by gate signal, but will be continuously on until the current between major terminals decreases below the holding current. In other words, you cannot turn it off with reverse signal unlike SCR. This property is called current-voltage threshold rise rate (commutation: dv/dt). In AC power control application, triac has to turn off conduction in each zero crossing or switch it twice in each cycle. This switching operation is called commutation. It is possible to turn off the triac at the end of half cycle by eliminating the gate signal when the load current (IL) is gained at the level equal to or lower than holding current. When triac commutes off-line, the direction of the voltage of the both ends of triac will be reversed and increase up to the maximum value of line voltage (VAC). At this point, the width of rise rate will be determined by dv/ dt and overshoot voltage, by the circuit. When triac commutes off-line, the voltage of both ends of triac will have the same voltage as the line voltage.
IL Inductive IL VAC G
<Inductive Circuit>
VT
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-39
Connection Diagrams
4. Schematic Diagrams
4-1 Main Circuit Diagram (1/16)
Samsung Electronics
- This Document can not be used without Samsung's authorization -
4-1
Connection Diagrams
4-2
Samsung Electronics
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Samsung Electronics
- This Document can not be used without Samsung's authorization -
4-3
Connection Diagrams
4-4
Samsung Electronics
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Samsung Electronics
- This Document can not be used without Samsung's authorization -
4-5
Connection Diagrams
4-6
Samsung Electronics
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Samsung Electronics
- This Document can not be used without Samsung's authorization -
4-7
Connection Diagrams
4-8
Samsung Electronics
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Samsung Electronics
4-9
Connection Diagrams
4-10
Samsung Electronics
Connection Diagrams
Samsung Electronics
- This Document can not be used without Samsung's authorization -
4-11
Connection Diagrams
4-12
Samsung Electronics
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Samsung Electronics
- This Document can not be used without Samsung's authorization -
4-13
Connection Diagrams
4-14
Samsung Electronics
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Samsung Electronics
4-15
Connection Diagrams
4-16
Samsung Electronics
- This Document can not be used without Samsung's authorization -
Connection Diagrams
(BLK)
* (BRW) 120K
(ORG)
0.22UF/16V /16V
/16V
600:600
*
,1W
*
(BLU)
*
(YEL) (GRN)
15nF/400V
Samsung Electronics
- This Document can not be used without Samsung's authorization -
4-17
Connection Diagrams
4-18
Samsung Electronics
- This Document can not be used without Samsung's authorization -
Connection Diagrams
18V
C402 104
R407 85KF
24VS
R419 5.6K
T401 KAB-006
1 7
D403 4KV
3 2
+ -
MHV-PWM CON03-#22
5 2
U103-B 7407
D404 1N4148
U101-A KA324
D402 4KV
C401 222
R409 430 R406 16.2KF D401 1N4148 C403 333 R410 1W 3 ZD401 1W 150V
OPC
5V
24VS 18V
1
T501 T1167
7
D502 4KV
R501 100
2
Q501 A708-Y R505 27K R503 100KF R502 2K DEV 50K R504 86.6KF C501 104
R506 86.6KF
C503 104
R508 47K
Q502 D526-Y
5 2
6 5
SUPPLY
U103-A 7407
R519 2.2K
R509 47K
R507 12KF
D501 1N4148
24VS
C102 104
DONGYANG INSTRUMENTS
TITLE
H.V.P.S
JC44-00017A
DATE 01/05/20
REV. 1.0
1 OF 2
Samsung Electronics
- This Document can not be used without Samsung's authorization -
4-19
Connection Diagrams
18V
C402 104
R407 85KF
24VS
R419 5.6K
T401 KAB-006
1 7
D403 4KV
3 2
+ -
MHV-PWM CON03-#22
5 2
U103-B 7407
D404 1N4148
U101-A KA324
D402 4KV
C401 222
R409 430 R406 16.2KF D401 1N4148 C403 333 R410 1W 3 ZD401 1W 150V
OPC
5V
24VS 18V
1
T501 T1167
7
D502 4KV
R501 100
2
Q501 A708-Y R505 27K R503 100KF R502 2K DEV 50K R504 86.6KF C501 104
R506 86.6KF
C503 104
R508 47K
Q502 D526-Y
5 2
6 5
SUPPLY
U103-A 7407
R519 2.2K
R509 47K
R507 12KF
D501 1N4148
24VS
C102 104
DONGYANG INSTRUMENTS
TITLE
H.V.P.S
MCKINLEY-HVPS JC44-00017A
DATE 01/05/20
REV. 1.0
1 OF 2
4-20
Samsung Electronics
- This Document can not be used without Samsung's authorization -
Connection Diagrams
F2 125V5A
LF2
C7 C-CX104224
10
13
TNR1 INR14D561K
C22
D5/A D10LC20U
24VG
C-CY222 GND
R5 2W100KJ
R6 1W100KJ
D1 BYV-26E
D6 D1NL20U
C24 35V100uF
9
4 3
IC3 IC-278RXX
GND
IN
OUT
R23 1/4W100J
12
11
D7 D1NL20U
CON2
1 2
1/8W470J
12VG
D9/A
15
5 6
R37 1/8W120J
F3
C34 10V3300uF 5V
GND
R22 1W180J
PC3 S21ME4FY
16
CS 6
CT
SB560 C-MY50V472J
2
OUT
IS
C17 50V104J
R24 1W47J
Q2
C12 35V33uF
RT
FB
C1
1
C13
R31 1/8W120J
C26 C-MY50V104
PT1 EER3435
C33 10V3300uF
5VG +24V ZD1 ZD-500MW30V ZD-500MW6.2V ZD2 R31 1/8W1KJ R32 1/8W1KJ RV1
R20
R25 1/8W10KJ
FUSER_ON
PC1 PC-123
R34 1.2KJ
R26 1/8W220J
R30 1/8W220J
C19
C20 C-MY50V104
C-MY50V104
Samsung Electronics
- This Document can not be used without Samsung's authorization -
4-21
Connection Diagrams
F2 250V3.15A
LF2
C7 C-CX104224
10
13
D5/B TNR1 INR14D561K R1 1W560KJ C22 C10 400V330uF R3 1W130V(ZEN) R4 2W100KJ C5 C-CY222 C11 C-MYN630V103 L1
1 2
D5/A D10LC20U
24VG
C-CY222 GND
R5 2W100KJ
R6 1W220KJ
D1 BYV-26E
D6 D1NL20U
C24 35V100uF
9
4 3
IC3 IC-278RXX
GND
IN
OUT
R23 1/4W100J
12
11
D7 D1NL20U
CON2
1 2
1/8W470J
12VG
D9/A
15
5 6
R37 1/8W120J
F3
C34 10V3300uF 5V
GND
R22 1W180J
PC3 S21ME4FY
16
CS 6
CT
SB560 C-MY50V472J
2
OUT
IS
C17 50V104J
R24 1W47J
Q2
C12 35V33uF
RT
FB
C1
1
C13
R31 1/8W120J
C26 C-MY50V104
PT1 EER3435
C33 10V3300uF
5VG +24V ZD1 ZD-500MW30V ZD-500MW6.2V ZD2 R31 1/8W1KJ R32 1/8W1KJ RV1
R20
R25 1/8W10KJ
FUSER_ON
PC1 PC-123
R34 1.2KJ
R26 1/8W220J
R30 1/8W220J
C19
C20 C-MY50V104
C-MY50V104
4-22
Samsung Electronics
Connection Diagrams
Samsung Electronics
4-23
Connection Diagrams
4-24
Samsung Electronics
Connection Diagrams
Samsung Electronics
4-25
Connection Diagrams
4-26
Samsung Electronics
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Samsung Electronics
4-27
Connection Diagrams
4-28
Samsung Electronics
This Manual is a property of Samsung Electronics Co. , Ltd. Any unauthorized use of Manual can be punished under applicable internaional and/or domestic law