Professional Documents
Culture Documents
Placa Si Finisaj Peste CTS
Placa Si Finisaj Peste CTS
outside
200 6
100 5
600
120 www.ubakus.de
4
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
100 3
60 2
20 1
inside
1 Parkett aus Weichholz (20 mm) 3 Knauf TecTem (100 mm) 5 Extruded polystyrene (100 mm)
2 Light weight concrete (60 mm) 4 Reinforced concrete (120 mm) 6 gravel 16/32 (200 mm)
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 mm
8 i
0 95 eT
u
ba =0,2 d
5
=0
,1
41 O ig u U
DI
N tzV ie dr Ne
U tan s
hu n 1 4 s au
es
c
nd EV Be nd au sivh
a n V ta
är
m st E E
En Bes Neu u
b
Pas
W Be 0 a =0,2
E V 2 1 6 b ,15
En 20 EV Neu V U . =0
G n
E 20 n U
GE nM aß us 40
20 ESa elm 5 - Ha KfW
G z 5 r
GE e
Ein fW BW -Lit bau
f W u K eG 3 u
K a Ne
e ub ärm
N EW
*Vergleich mit dem Höchstwert gemäß GEG 2020 für erstmaligen Einbau, Ersatz oder Erneuerung von Außenwänden (Anlage 7, Zeile 1a,1b). Page 1
All statements without guarantee
Temperature profile
Temperature profile
20 Temperature
18 Dew point
1 2 3 4 5 6
16
14
12 1 Parkett aus Weichholz (20 mm)
Temperature [°C]
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
www.ubakus.de Outside
Temperature and dew-point temperature in the component. The dew-point indicates the temperature, at which water vapour
condensates. As long as the temperature of the component is everywhere above the dew-point temperature, no
condensation occurs. If the curves have contact, condensation occurs at the corresponding position.
Page 2
All statements without guarantee
Moisture proofing
For the calculation of the amount of condensation water, the component was exposed to the following constant climate for
90 days: inside: 20°C und 50% Humidity; outside: -5°C und 80% Humidity. This climate complies with DIN 4108-3.
This component is free of condensate under the given climate conditions.
Humidity
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
The temperature of the inside surface is 18,9 °C leading to a relative humidity on the surface of 54%.Mould formation is not
expected under these conditions.
The following figure shows the relative humidity inside the component.
Page 3
All statements without guarantee
Heat protection
The following results are properties of the tested component alone and do not make any statement about the heat protection
of the entire room:
Temperature profile
This document has been generated by the U-value calculator on www.ubakus.de. If you are harmed by the free use of these contents, the service provider is only liable in case of
30
1 Parkett aus Weichholz (20 mm)
Temperature [°C]
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
16
0 100 200 300 400 500 600
Inside [mm]
www.ubakus.de Outside
30
28
26
24
22
20
18
16
12 14 16 18 20 22 24 2 4 6 8 10 12
[time of day]
Top:Temperature profile within the component at different times. From top to bottom, brown lines: at 3 pm, 11 am and 7 am
and red lines at 7 pm , 11 pm and 3 am.
Bottom:Temperature on the outer ( red ) and inner ( blue ) surface in the course of a day. The arrows indicate the location of
the temperature maximum values . The maximum of the inner surface temperature should preferably occur during the
second half of the night.
Phase shift* non relevant Heat storage capacity (whole component): 749 kJ/m²K
Amplitude attenuation ** >100 Thermal capacity of inner layers: 271 kJ/m²K
TAV *** 0,001
* The phase shift is the time in hours after which the temperature peak of the afternoon reaches the component interior.
** The amplitude attenuation describes the attenuation of the temperature wave when passing through the component. A value of 10
means that the temperature on the outside varies 10x stronger than on the inside, e.g. outside 15-35 °C, inside 24-26 °C.
*** The temperature amplitude ratio TAV is the reciprocal of the attenuation: TAV = 1 / amplitude attenuation
Note: The heat protection of a room is influenced by several factors, but essentially by the direct solar radiation through windows and the
total amount of heat storage capacity (including floor, interior walls and furniture). A single component usually has only a very small
influence on the heat protection of the room.
Page 4