Professional Documents
Culture Documents
Brushbond Flxiii3
Brushbond Flxiii3
Uses Properties
Brushbond FLXIII when fully cured, provides a seamless Pot life at 35ºC : Approx. 1 hour
elastic waterproof membrane for use in roof areas, wet 2
Adhesion to substrate : 1 N/mm
areas, pre-cast joints where a tough elastomeric water tight (ASTM D4541:1989)
membrane is required. Shore A hardness : 62
(ASTM D2240:1997)
Advantages 2 2
Tensile strength (N/mm ) : 0.9 N/mm
Can be applied to damp substrates (ASTM D412-91)
Elongation at break : 127%
No primer required (ASTM D412-91)
Elastomeric - able to bridge cracks Water Permeability : Nil
(DIN 1048:Pt 5: 1991)
Able to take foot traffic when cured
Water vapour transmission : 0.632 g/hr-m²
Factory pre-blended two component system ensure (ASTM E96:1995)
quality control at site Crack bridging : Passed
Low Temperature Flexibility : Passed
Description (ASTM C 765:1993)
Setting time *
Brushbond FLXIII is a two component polymer modified
- Foot traffic : 4 hrs + 1 hr
waterproof membrane which is supplied in readymix kits. - Light vehicle : 24 hrs + 3 hrs
When mixed, an easily brushable coating is produced. It can
Note*: On clean dry concrete, with adequate airflow
simply be applied by a stiff brush, roller, or trowel to obtain
the desired thickness. (ventilation) at 25ºC to 35ºC
Application Estimating
For best results damp the surface before coating with Supply
Brushbond FLXIII. Use a short, stiff bristle brush preferably Brushbond FLXIII Kit : 15 litres pack
120 to 200 mm in width. Apply like a paint using one or two Powder : 14.8 kg
coats as required. Liquid : 10 kg
For trowel application, ensure that the substrate is levelled Coverage / yield
and repaired of any undulations or pot holes. Brushbond FLXIII : 15m²/pack applied at 1mm
Brushbond FLXIII should be applied to the recommended thick (2 coats of 500
microns thick)
coverage as follows:
Note: Coverage figures are theoretical and due to wastage
It is recommended that general re-surfacing and areas
subjected to light foot traffic should receive a Brushbond factors and the variety nature of possible
FLXIII in two coats of 500 microns each to give a 1mm thick substrates, practical coverage will be reduced.
coating. Additional coatings may be required for areas of
Storage
moderate to heavy pedestrian conditions.
Cleaning Brushbond FLXIII has a shelf life of 6 months in unopened
pack, kept in a dry store. In high humidity locations, the shelf
Brushbond FLXIII should be removed from tools and life may be reduced to 4 months.
equipment immediately after use with clean water. Hardened
material can only be removed mechanically. Precautions
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.
Fosroc Jordan
Head Office Regional Offices: email: enquiryjordan@fosroc.com
P.O Box 253,
King Abdullah II Industrial State Amman-Khalda Offices: Tel: (06) 535 9562 Fax: (06) 535 9563
Sahab 11512, Jordan Amman-Sahab Factory: Tel: (06) 402 2665 Fax: (06) 402 9475
Aqaba Showroom: Tel: (03) 205 0061 Fax: (03) 205 0062
www.fosroc.com