Professional Documents
Culture Documents
FIRERAY F5K Beam Detector - UserGuide
FIRERAY F5K Beam Detector - UserGuide
USER GUIDE
English
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:38 Page 2
IMPORTANT
PLEASE NOTE: The infrared beam path MUST be kept
clear of obstructions at all times!
Contents
Troubleshooting
17 System in Fault/Trouble
18 Error Codes
20 LASER Not Visible
21 Home Position
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:38 Page 4
50cm
50—100m = 4
50cm
18—50m = 1
50cm
50cm 8—18m = 1
8-100m Use Short Range
Mask
8-100m
Ensure clear line of sight Mount on solid surfaces (structural wall or girder)
from Detector to Reflector
4
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:38 Page 5
Ext Ext
Reset Reset
N/O COM N/C N/O COM N/C N/O COM N/C N/O COM N/C Apply a
voltage of
Fire Fire 5V to 40V
Resistor Resistor to ‘Ext
Reset’
ZONE - EOL contact for
ZONE + at least 2
seconds to
SUPPLY - clear a
SUPPLY + Latched
EARTH/SCREEN Fire
Wiring for all other System Controllers (where more than one System Wiring for a single System Controller or last System condition
Controller is on one zone) Controller on one zone
(Not to be used for UL region installations. Please refer to supplied CD
for UL region installation multiple-System Controller wiring)
• Check operation of Fire and Fault connection on Fire Components not supplied (Check Fire Control Panel
Panel manufacturer for values):
• ALWAYS use a separate screened 2-core cable for • Fire Resistor (Some Zone and Switch Interface
each detector head Modules do not need a Fire Resistor - replace Resistor
• CAUTION: For system monitoring – Do not use with a short circuit.)
looped wire under any terminals. Break wire run to • Detector Continuity Diode
provide monitoring of connections • End Of Line (‘EOL’) component 5
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:38 Page 6
2 seconds
7
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:38 Page 8
8
Menu Navigation
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:38 Page 9
9
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:38 Page 10
7. LASER Targeting
10
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:38 Page 11
11
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:38 Page 12
When a Detector is
connected but not
‘Found’ the system will
display:
12
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 13
Fire Threshold
How to change the
threshold at which the
Detector will detect a Fire
(Set for each Detector)
Latching/Non-Latching
Non-Latching Latching
Mode
How to select either
Latching Mode (system will
stay in Fire condition after
the fire clears) or Non-
Latching Mode (system will
automatically return to
normal condition after the
fire clears) Use to move between icons in the
Detector Menu, until the graph and bell icons
(Set for the system not each individual Detector) are shown
13
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 14
After installation or cleaning, it is recommended that a manual Fire and Fault test is performed:
Fire Test: Cover the Reflector slowly so that it takes longer than
5 seconds to cover. The System Controller will signal Fire to the
Fire Control Panel
15
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 16
60 seconds
YES
YES
17
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 18
Detector Not Found Detector is connected but not Compensation Level Not Zero
System Controller could not find ‘Found’ Compensation must equal zero
Detector. Also displayed during A Detector is connected but not when ‘Set’ is selected.
power up. ‘Found’ • Re-align Detector using Auto-
• Wait 45 seconds for system to • Follow ‘Find’ process and Align
power up align if necessary
• Check wiring between System
Controller and Detector (Voltage
to Detector should be 11—13V)
18
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 19
Cannot Zero During ‘S-00’ No Signal During ‘S-01’ in ‘Set’ ‘Centre’ Stage of Alignment
in ‘Set’ The Reflector was not uncovered Failed
The Reflector was not during ‘S-01’. Detector has aligned on
covered or the Detector was • Ensure Reflector was something other than the
not aligned onto the Reflector. uncovered when ‘S-01’ was Reflector
• Ensure Reflector was selected • Ensure clear line of sight from
completely covered with a Detector to Reflector for a
non-reflective material radius of 0.5m
• Re-align Detector using
Auto-Align
19
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 20
20
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 21
21
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 22
Busy
Warning
Transmit
Signal Strength
Received
System Locked/ Signal Strength
Unlocked %/V
Bar Graph
22
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 23
Detector
NORMAL: GREEN
FAULT: YELLOW
FIRE: RED
2 3 4
1 5
System Controller
Indicators 1 to 4 show status for Detectors 1 to 4:
NORMAL: No flash
FAULT: YELLOW
FIRE: RED
Indicator 5 flashes GREEN to indicate NORMAL
System Controller status.
All indicators flash every 10 seconds.
23
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 24
Controller parameters
Detector parameters
24
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 25
Controller parameters
Detector parameters
25
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 26
Home Position Detector Settings LASER Targeting Beam Alignment Fire Threshold
26
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 27
Default is Non-Latched
Set Detector Number Set Distance Set Fire Latch / Reset Auto-Optimise Motor
Movement On / Off
Set TX Power ** Set Compensation Level ** Set RX Gain ** Set Zero / 100%
27
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 28
WARNING
Care must be taken when • Units of Measurement
changing the Pass Code. Changes between ‘Metric’ and ‘Imperial’
If the code is lost, contact
the manufacturer for Pass • Change Pass Code
Code reset. Use to access each digit
Use to change the digit
Press to save the new Pass Code and return to the settings menu
28 Press to cancel the change and return to the Engineering menu
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 29
29
Reflector (Single) 3.9 (100) 3.9 (100) 0.4 (10) 0.2 (0.1)
0044-034-01 - THESEUS UG - ENGLISH:0044-003-01 User Guide.qxd 23/06/2009 08:39 Page 30