Professional Documents
Culture Documents
ETG - ARUZE TECHNICAL TRAINING LBW - v02
ETG - ARUZE TECHNICAL TRAINING LBW - v02
5. SPECIFICATIONS .............................................. 12
5.1 DIMENSION & WEIGHT ..................................... 12
5.2 ELECTRICAL SPECIFICATIONS .......................... 12
Wheel
Motor
27,37 16 7,26,28,29
19 ,40,47
22,23,24 20
F3
,41
38
F6
6 21
F4 F9 Gear head
16
39
2
F4 18
Motor
F5 13
F5
3,46 5
15
14 F1
F3
19 20 F4 F4
8 F2
VIEW A 1,30,42
17
,44,45
,43
Servo pack
Motion controller
Servo
Wheel Motor
AC220-240V
When the wheel stops, machine detect the win position following steps.
The winning position is decided by software RNG just before the wheel starts turning.
POINTER RUNAWAY The wheel is not moving but the pointer is If the pointer sensor detects a change during the
moving. Bet or Result time, an error will occur.
When a wheel action in which the wheel spins If the pointer sensor does not respond in the
backwards occurs, and the pointer goes over pause before the wheel spinning backwards,
the pin. and error will occur.
POINTER ERROR The wheel is moving but the pointer does not In the motor operation process, when the pointer
move. sensor responds the reset value is saved to the
motor controller. If this value is over 1.5 pockets,
it will cause an error.
WHEEL COVER OPEN The wheel cover (glass) has been opened. The Wheel Cover door switch detects an OPEN
state.
WHEEL MOTOR FAULT The motor is not operating normally. An error occurs with the motor driver.
54 spots
52 spots (Macau exclusive)
1.6.1 54 spots
TYPE- B Spots Prob Odds Odds RTP TYPE- D Spots Prob Odds Odds RTP
1 26 0.481481481 2 1:1 96.296% Min= 90.741% 1 23 0.425926 2 1:1 85.185% Min= 83.333%
T 3 13 0.240740741 4 3:1 96.296% Max= 96.296% T 2 15 0.277778 3 2:1 83.333% Max= 94.444%
Y 6 7 0.12962963 7 6:1 90.741% Y 5 8 0.148148 6 5:1 88.889%
P 12 4 0.074074074 13 12 : 1 96.296% P 11 4 0.074074 12 11 : 1 88.889%
E 25 2 0.037037037 26 25 : 1 96.296% E 24 2 0.037037 25 24 : 1 92.593%
Joker 1 0.018518519 52 51 : 1 96.296% Joker 1 0.018519 51 50 : 1 94.444%
B Flag 1 0.018518519 52 51 : 1 96.296% D Flag 1 0.018519 51 50 : 1 94.444%
7 54 95.503% 95.50% 7 54 89.683%
Average return
Default Odds Return Spots Probability include multiplier RTP%
1 1:1 2 24 46.15% 2.08 96.00% MINIMUM RTP 84.00%
3 3:1 4 12 23.08% 4.16 96.00% MAXIMUM RTP 96.00%
5 5:1 6 8 15.38% 6.24 96.00% AVERAGE RTP 92.00%
10 10 : 1 11 4 7.69% 11.44 88.00%
20 20 : 1 21 2 3.85% 21.84 84.00%
GOD 45 : 1 46 1 1.92% 47.84 92.00%
CHILDREN 45 : 1 46 1 1.92% 47.84 92.00%
TOTAL --- --- 52 100% --- 92.00%
1
6 3
*Need to disconnect
a connector.
4 5
2
Remove 4 screws
7) Cleaning glass
Clean the glass and projector screen on the glass.
3.1 Sensor setting 1) Go to MAIN AUDIT > TEST > BIG WHEEL UNIT
TEST
2) Select "INITIALIZE" and press "ENTER".
(Wheel stops automatically.)
3) Set up “STOP POCKET”, “STOP PATTERN” as
below;
STOP POCKET : 1
WHEEL UNIT STOP PATTERN : 7
POINTER
SENSOR
SPEED :
MOVE :
-------------------------
MOVE STOP :
MOVE SLOW :
INITIALIZE :
ERROR RESET :
SERVO ON :
SERVO OFF :
-------------------------
SENSOR TEST 1 :
SENSOR TEST 2 :
<PIN SENSOR setting procedure> MOVE FOR SETTING :
(When pressing
"SET BUTTON" the
on the second "SETBUTTON",
70mm time Green Light is off
in a second.)
Set the SLIDE
SWITCH SET to
RUN
7) Press the "SET BUTTON" twice while holding the When sensor is
white plate. working on
(Wait one second after pressing first, and then press "RUN"
1
6 3
4 5
2
Check if the
screw is loose
1100
1006
2420
3912
2900
2633
2460