Professional Documents
Culture Documents
Shock Absorber 3 - 1 - 8
Shock Absorber 3 - 1 - 8
3100-312-000R
Assembly Procedures
3/21/2005
Titan Specialties, Ltd. • P.O. Box 2316, Pampa, TX 79066-2316 • Tel. 800-692-4486 • Fax 806-669-6674
www.titanspecialties.com
Page 1 of 7
Specifications
Application:
The 3-1/8” shock absorber assembly can be placed between logging and ballistic tools to
provide high frequency shock wave isolation that is produced when the explosive device is
initiated. The use of this tool does not guarantee total protection, but field data indicates that it
is very effective in the reduction of damage to sensitive components exposed to repeated
ballistic impact forces.
These instructions are intended as a guide to assist the reader in the assembly of the tool,
perform preventative maintenance and to encourage the development of their own procedures.
Disassembly can be achieved by reversing the assembly sequence. It is assumed that the tool
has been completely disassembled, O-rings and rubber components removed, metal parts
cleaned and degreased and that all components are in good working condition. A Digital
Voltmeter should be used throughout the assembly procedure to confirm proper electrical
condition of the connectors and lead wire assembly.
The Shock Absorber is assembled from the bottom up. Time for complete bench assembly:
Approximately 10 minutes.
Titan Specialties, Ltd. • P.O. Box 2316, Pampa, TX 79066-2316 • Tel. 800-692-4486 • Fax 806-669-6674
www.titanspecialties.com
Page 2 of 7
Tools recommended for assembly:
Titan Specialties, Ltd. • P.O. Box 2316, Pampa, TX 79066-2316 • Tel. 800-692-4486 • Fax 806-669-6674
www.titanspecialties.com
Page 3 of 7
Install Upper Shock Cushions and Back-Up
Rings onto Mandrel Body, alternating each as
shown (see print attached for details).
Titan Specialties, Ltd. • P.O. Box 2316, Pampa, TX 79066-2316 • Tel. 800-692-4486 • Fax 806-669-6674
www.titanspecialties.com
Page 4 of 7
Attach opposite end of Cable and Boot
assembly to the Feed Thru assembly Tool.
Titan Specialties, Ltd. • P.O. Box 2316, Pampa, TX 79066-2316 • Tel. 800-692-4486 • Fax 806-669-6674
www.titanspecialties.com
Page 5 of 7
Install the Support Ring using the spanner
wrench end of the Installation Tool.
Titan Specialties, Ltd. • P.O. Box 2316, Pampa, TX 79066-2316 • Tel. 800-692-4486 • Fax 806-669-6674
www.titanspecialties.com
Page 6 of 7
Install Stem Protector.
Prints Attached:
Additional Help:
If you require additional assistance or have any questions or comments, please direct them to
instruments@titanspecialties.com or support@titanspecialties.com
Titan Specialties, Ltd. • P.O. Box 2316, Pampa, TX 79066-2316 • Tel. 800-692-4486 • Fax 806-669-6674
www.titanspecialties.com
Page 7 of 7
3100-312-000B.dwg 2/2/2005 1:33:45 PM Scaled to fit
3100-312-000R.dwg 2/2/2005 1:36:14 PM Scaled to fit
3100-312-000B-SPARE PARTS.dwg 2/2/2005 1:34:44 PM Scaled to fit
3100-312-000R-SPARE PARTS.dwg 2/2/2005 2:12:42 PM Scaled to fit