Professional Documents
Culture Documents
Toyota Land Cruiser Troubleshooting For Audio System
Toyota Land Cruiser Troubleshooting For Audio System
Toyota Land Cruiser Troubleshooting For Audio System
Home
Top
Contacts
Search
Search
Troubleshooting
Buying A Used Car Out of State?
VIN Number
Research the car's Enter VIN SEARCH VIN
history report
(a) Diagnosis start-up For shifting to diagnosis mode, turn the ignition switch ON and push the "DISC" switch 3
times while pressing "ch1" and "ch6" switches.
HINT: To exit the diagnosis mode, push the "DISC" switch for 1.7 sec. or turn the ignition switch to ACC or
OFF. (b) Element check mode After the diagnosis start-up, the system enters the element check mode. Check
that the all elements light up.
HINT: By pressing the "TUNE UP" switch, the system enters the "Service Check Mode". (c) Switch check
mode
1. Element check mode is started at the same time with the switch check mode.
2. Check that there is a beep sound when any switch is pressed.
HINT: By pressing "TUNE UP" switch, the system enters the "Service Check Mode".
https://www.tlacruiser.com/troubleshooting-338.html 1/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
1. After the element check and switch check is completed, the system enters service check mode when
"TUNE UP" switch is pressed.
2. Error codes over the tuner and connected equipments are displayed on the screen of the tuner.
good: No DTC is detected for both "System Check Confirmation" and "Diagnosis Memory Response".
nCon: The component does not respond to the "Diagnosis On Instruction" command.
Applicable to only the system where connected components are limited to be used.
ECHn: Application of new version has been confirmed by the "Diagnosis On Check", and there is one or
more DTC which indicates "Replacement" in the "System Check Result Response" or "Diagnosis
Memory Response".
CHEC: Application of new version has been confirmed by the "Diagnosis On Check", and there is no
DTC which indicates "Replacement" in the "System Check Result Response" or "Diagnosis Memory
Response", but one or more DTC which indicates "Check" is identified.
Old: Application of old version is confirmed by the "Diagnosis On Check", and DTC is identified in the
"System Check Result Response" or "Diagnosis Memory Response".
nrES: No response is identified to the "System Check Start Instruction" and "Request for System Check
Result" commands.
HINT:
Check the present and past condition of components by performing the System Check and collecting
stored DTC memories.
Check results are displayed as one of the following six indications: "good", "ECHn", "CHEC","nCon",
"Old" or "nrES".
Example: Connection parts ( physical address): Radio receiver (P190), RSA ECU (P1F4), DVD player (P1A0)
https://www.tlacruiser.com/troubleshooting-338.html 2/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 3/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 4/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 5/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
HINT: As starting Main AVC-LAN to operate the diagnosis mode, Sub AVC-LAN is automatically to the mode.
Perform the diagnosis mode operation on the RSA panel. (a) Element check mode After the diagnosis start-up,
the system enters the element check mode. Check that the all elements light up.
HINT: By pressing the "TUNE UP" switch, the system enters the "Service Check Mode". (b) Switch check
mode
1. Element check mode is started at the same time with the switch check mode.
2. Check that there is a beep sound when any switch is pressed.
HINT: By pressing "TUNE UP" switch, the system enters the "Service Check Mode".
https://www.tlacruiser.com/troubleshooting-338.html 6/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
1. After the element check and switch check is completed, the system enters service check mode when
"TUNE UP" switch is pressed.
2. Error codes over the tuner and connected equipments are displayed on the screen of the tuner.
good: No DTC is detected for both "System Check Confirmation" and "Diagnosis Memory Response".
nCon: The component does not respond to the "Diagnosis On Instruction" command.
Applicable to only the system where connected components are limited to be used.
ECHn: Application of new version has been confirmed by the "Diagnosis On Check", and there is one or
more DTC which indicates "Replacement" in the "System Check Result Response" or "Diagnosis
Memory Response".
CHEC: Application of new version has been confirmed by the "Diagnosis On Check", and there is no
DTC which indicates "Replacement" in the "System Check Result Response" or "Diagnosis Memory
Response", but one or more DTC which indicates "Check" is identified.
Old: Application of old version is confirmed by the "Diagnosis On Check", and DTC is identified in the
"System Check Result Response" or "Diagnosis Memory Response".
nrES: No response is identified to the "System Check Start Instruction" and "Request for System Check
Result" commands.
HINT:
Check the present and past condition of components by performing the System Check and collecting
stored DTC memories.
Check results are displayed as one of the following six indications: "good", "ECHn", "CHEC","nCon",
"Old" or "nrES".
Example: Connection parts ( physical address): Radio receiver (P190), RSA ECU (P1F4), DVD player (P1A0)
https://www.tlacruiser.com/troubleshooting-338.html 7/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 8/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 9/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 10/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
w/ Navigation system ()
HINT: *1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for
starting an engine.
*2: It may be stored when the engine key is turned 1 min. angain after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component with the
ignition switch in ACC or ON, this code is stored.
https://www.tlacruiser.com/troubleshooting-338.html 11/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
01
Error is detected in internal
(Communication 21 ROM Error Replace radio receiver assembly
ROM.
Control)
01
Error is detected in internal
(Communication 22 RAM Error Replace radio receiver assembly.
RAM.
Control)
Component in which this
code is recorded has been Check harness for power
disconnected from system supply system of radio
01 *2 with ignition in ACC or ON.
Absence of receiver assembly.
(Communication D6
Master Check harness for
Control) Or, when this code was
communication system of
recorded, radio receiver
radio receiver assembly.
assembly was disconnected.
https://www.tlacruiser.com/troubleshooting-338.html 13/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
Abnormal condition is
detected in AM tuner.
60 (Radio receiver
43 AM Tuner Error Replace radio receiver assembly.
assembly) Inspect radio receiver
assembly.
HINT: *1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for
starting an engine.
*2: It may be stored when the engine key is turned 1 min. angain after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component with the
ignition switch in ACC or ON, this code is stored.
Transmission to component
shown by auxiliary code has bee If same auxiliary code is
01 failed. recorded in other component(s),
DC Transmission
(Communication check harness for power supply
*2 Error
Control) (This code does not necessarily and communication system of
mean actual failure.) components shown sub code.
https://www.tlacruiser.com/troubleshooting-338.html 15/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
ON/OFF
01 Error is detected in ON/OFF
Instruction
(Communication E2 control command from radio Replace radio receiver assembly
Parameter
Control) receiver assembly.
Error
Registration Request
command is output from
slave component.
01 Registration Since this DTC is provided for
By reception of connection
(Communication E3 Request engineering, it may be detected
check Instruction,
Control) Transmission when no actual failure exists.
Registration Request
command is output from
sub-master component.
HINT: *1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for
starting an engine.
*2: It may be stored when the engine key is turned 1 min. angain after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component with the
ignition switch in ACC or ON, this code is stored.
https://www.tlacruiser.com/troubleshooting-338.html 16/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
RSA panel
Transmission to component
shown by auxiliary code has bee If same auxiliary code is
01 failed. recorded in other component(s),
DC Transmission
(Communication check harness for power supply
*2 Error
Control) (This code does not necessarily and communication system of
mean actual failure.) components shown sub code.
https://www.tlacruiser.com/troubleshooting-338.html 17/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
HINT: *1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for
starting an engine.
*2: It may be stored when the engine key is turned 1 min. angain after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component with the
ignition switch in ACC or ON, this code is stored.
Transmission to component
shown by auxiliary code has If same auxiliary code is
been failed. recorded in other component,
01 *4
Transmission check harness for power
(Communication DC
Error (Detecting this DTC does not supply and communication
Control)
necessary mean actual system of components shown
failure.) sub code.
HINT: *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage
for starting an engine.> *2: This code may be stored when the engine key is turned again 1 min. after engine
start.> *3: This code may be stored when the engine key is turned again after engine start.> *4: When 210 sec.
has passed after pulling out the power supply connector of the master component with the ignition switch in
ACC or ON, this code is stored.
https://www.tlacruiser.com/troubleshooting-338.html 19/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
If same sub-code is
Transmission to component recorded in other
01 *4 shown by sub-code has been component, check
Transmission
(Communication DC failed. (Detecting this DTC does harness for power supply
Error
Control) not necessary mean actual and communication
failure.) system of components
shown sub code.
Registration Request
command is output from
slave component.
01 Registration Since this DTC is provided for
Registration connection
(Communication E3 Request engineering, it may be detected
check Instruction,
Control) Transmission when no actual failure exists.
Registration Request
command is output from
sub-master component.
https://www.tlacruiser.com/troubleshooting-338.html 20/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
01
Abnormal condition of RAM is
(Communication 22 RAM Error Replace DVD player.
detected.
Control)
Countermeasure and
Logical address DTC Diagnosis item Diagnosis content
inspeced parts
Transmission to component
If same auxiliary code is
shown by auxiliary code has
01 bee failed. recorded in other component(s),
DC
(Communication Transmission Error check harness for power supply
*2
Control) (This code does not necessarily and communication system of
mean actual failure.) components shown sub code.
https://www.tlacruiser.com/troubleshooting-338.html 21/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
"Registration Completion
01 Registration Since this DTC is provided for
E0 Instruction" command
(Communication Completion engineering, it may be detected
*1 fromradio receiver assembly
Control) Instruction Error when no actual failure exists.
cannot be received.
01 ON/OFF Error is detected in ON/OFF
Replace radio receiver
(Communication E2 Instruction control command from radio
assembly
Control) Parameter Error receiver assembly.
Registration Request
command is output from
slave component.
01 Registration By reception of Since this DTC is provided for
(Communication E3 Request connection check engineering, it may be detected
Control) Transmission Instruction, Registration when no actual failure exists.
Request command is
output from sub-master
component.
NOTICE: When replacing the internal mechanism (computer part) of the audio system, be careful that no part
of your body or clothing comes in contact with the terminals of the leads from the IC, etc. of the replacement
part (spare part).
HINT: This inspection procedure is a simple troubleshooting which should be carried out on the vehicle during
system operation and was prepared on the assumption of system component troubles (except for the wires and
connectors, etc.).
https://www.tlacruiser.com/troubleshooting-338.html 22/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
Always inspect the trouble taking the following items into consideration.
The term "AM" includes LW,MW and SW, and the term "FW" includes UKW.
https://www.tlacruiser.com/troubleshooting-338.html 23/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
2 Radio DISPLAY INDICATES WHEN POWER SWITCH TURNED TO "ON", BUT NO SOUND
(INCLUDING "NOISE") IS PRODUCED
https://www.tlacruiser.com/troubleshooting-338.html 24/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 25/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 26/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
11 Tape Player POWER COMING IN, BUT TAPE PLAYER NOT OPERATING
https://www.tlacruiser.com/troubleshooting-338.html 27/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 28/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 29/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 30/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
24 Power Amplifier POWER COMIMG IN, BUT WOOFER (POWER) AMPLIFIER NOT
OPERATING
https://www.tlacruiser.com/troubleshooting-338.html 31/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 32/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
https://www.tlacruiser.com/troubleshooting-338.html 33/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
29 Steering Pad Switch A AUDIO SYSTEM CANNOT BE OPERATED WITH STEERING PAD
SWITCH
https://www.tlacruiser.com/troubleshooting-338.html 34/36
11/11/23, 9:40 PM Toyota Land Cruiser: Troubleshooting - Audio system - Body Electrical
Description
Inspection
Troubleshooting
Toyota Land Cruiser Service Manual / Body Electrical / Audio system / Troubleshooting
Enter a VIN
Search
Starting
Lubrication
Maintenance
Categories
Home
Toyota Land Cruiser Owners Manual
Toyota Land Cruiser Service Manual
https://www.tlacruiser.com/troubleshooting-338.html 36/36