Professional Documents
Culture Documents
CONDENSERS
CONDENSERS
DEFINITION:
Condensers and capacitors are the same components. Both terms describe the same
component and essentially there is no difference. However, the term condenser had
been the word used to describe capacitors historically. The word capacitor came
into use several decades ago and now it is used more commonly, although the
word condenser is still in use as well. So, the main difference between capacitor
and condenser is that the term capacitor is a relatively newer term while
condenser is an older term.
Condenser is an older word for a capacitor. In fact, the term is a misnomer. The
first types of capacitors to be made were Leyden jars (shown below). These were
built in the 1700s, and people at the time thought that electric current was like a
fluid and that Leyden jars stored charges by condensing the fluid.
The use of the term condenser has largely been replaced by the term capacitor in
many fields of science and engineering, although “condenser” is still
occasionally used. For instance, in automobile engineering, the word “condenser”
is still frequently used to refer to capacitors.
A mirror, lens, or combination of lenses used to gather light and direct it upon an
Object or through a projection lens.
A lens that condenses light in a small area.
It is often used to direct light onto the projection lens in a projector.
“A capacitor is a device used to store charge in an electric circuit. It consists of two
conductors on which charge can be stored, separated by a layer of dielectric.”
Capacitors have the following circuit symbol:
WORKING:
When a capacitor is connected across the terminals of a cell, the positive
side of the cell can draw out negatively-charged electrons from one plate in the
capacitor and deposit negative charges on the other side. This causes a potential
difference to build up across the capacitor, which opposes the potential difference
across the battery. This slows down the current, and eventually brings the flow of
electrons in the circuit to a complete halt.
If the battery is removed and the two terminals of the capacitor are connected via a
resistor, then the potential difference across the capacitor can now drive a current:
the excess electrons from the negative side of the capacitor attempt to flow to the
positive side. As this happens, the potential difference across the capacitor drops
exponentially, and so does the current. Eventually, charges would be evenly
distributed across the capacitor’s plates once again. The potential difference across
the plates drops to 0 at this point, and the current stops.
ENERGY STORAGE:
The most common use for capacitors is energy storage. A capacitor can store
electric energy when it is connected to its charging circuit. And when it is
disconnected from its charging circuit, it can dissipate that stored energy, so it can
be used like a temporary battery. Capacitors are commonly used in electronic
devices to maintain power supply while batteries are being changed.
Conventional electrostatic capacitors provide less than 360 joules per kilogram of
energy density, while capacitors using developing technology can provide more
than 2.52 kilojoules per kilogram.
● In car audio systems, large capacitors store energy for the amplifier to use on
demand.
● An uninterruptible power supply (UPS) can be equipped with
maintenance-free capacitors to extend service life.
OSCILLATORS:
TUNING CIRCUITS:
Variable capacitors are used in tuning circuits on radio systems by connecting them
to an LC oscillator, as explained at Electronixandmore.com. The capacitor charges
and then discharges into a coil of wire, generating a magnetic field. Once the
capacitor is fully discharged, the magnetic field starts to collapse, recharging the
capacitor. This charging and discharging current takes place at regular intervals,
but it can be changed by altering the capacitor. If the frequency of these intervals is
the same as the frequency of a nearby radio station, then the amplifier in the radio
will strengthen this signal and you will hear the broadcast.
COUPLING:
Capacitors pass AC but block DC signals (when charged up to the applied DC
voltage), they are often used to separate the AC and DC components of a signal in
a process called “capacitor coupling”. This is used in the case of a loudspeaker.
Speakers work by converting an alternating current into sound, but they could be
damaged by any direct current that reaches them. A capacitor prevents this from
happening.