Professional Documents
Culture Documents
C5270 CMM 028
C5270 CMM 028
D254-, R2254-SERIES
Revision No. 28 dated Mar 31/2020 is attached and covers all components held by every operator.
For Myanmar Airways (MMA) use only
DEFINITIONS
R = REVISION
N = NEW
D = DELETED
FILING INSTRUCTIONS
– Make certain that the content of the manual is in compliance with the LIST OF EFFECTIVE
PAGES.
Corrections.
TL
Page 1
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
TL
Page 2
25-41-58 Mar 31/20
DIEHL Aviation Hamburg GMBH
Hein-Sass-Weg 41
21129 Hamburg
Germany
www.diehl.com/aviation
CAGE CODE C5270
LAVATORY A
For Myanmar Airways (MMA) use only
D2547160101800 D2549010407600
D2547160900800 D2549010407800
D2549010300000 D2549010408000
D2549010300200 D2549010408200
D2549010300400 D2549010408400
D2549010300600 D2549010408600
D2549010300800 D2549010408800
D2549010301000 D2549010409000
D2549010301200 D2549010409200
D2549010301400 D2549010409400
D2549010301800 D2549010409600
D2549010302000 D2549010409800
D2549010406600 D2549010410000
D2549010407200 D2549010410200
D2549010407400 D2549010410400
(cont.)
D2549010410600 D2549020302600
D2549010410800 D2549020303000
D2549010411000 D2549020303200
D2549010411600 D2549020303400
D2549010411800 D2549020303600
D2549010412000 D2549020303800
D2549010412200 D2549020304000
D2549010412400 D2549020304200
For Myanmar Airways (MMA) use only
D2549010412600 D2549020304400
D2549010412800 D2549020304600
D2549010413000 D2549020304800
D2549010413200 D2549020305000
D2549010413400 D2549020305200
D2549010413800 D2549020305400
D2549010414000 D2549020305600
D2549010414200 D2549020305800
D2549010414400 D2549020306000
D2549010414600 D2549020306200
D2549010414800 D2549020306400
D2549020301200 D2549020306600
D2549020301400 D2549020306800
D2549020302200 D2549020307000
D2549020302400 D2549020307200
D2549020307400 D2549020312200
D2549020307600 D2549020312400
D2549020307800 D2549020312600
D2549020308000 D2549020312800
D2549020308200 D2549020313000
D2549020308400 D2549020313200
D2549020308600 D2549020313400
D2549020308800 D2549020313600
For Myanmar Airways (MMA) use only
D2549020309000 D2549020313800
D2549020309200 D2549020314200
D2549020309400 D2549020314400
D2549020309600 D2549020314600
D2549020309800 D2549020314800
D2549020310000 D2549020900000
D2549020310200 D2549020900200
D2549020310400 D2549020900400
D2549020310600 D2549020900600
D2549020310800 D2549020900800
D2549020311000 D2549020901000
D2549020311200 D2549020901200
D2549020311400 D2549020901400
D2549020311800 D2549020901600
D2549020312000 D2549020901800
D2549020902000 D2549020906600
D2549020902200 D2549020906800
D2549020902400 D2549020907000
D2549020902600 D2549020907200
D2549020902800 D2549020907400
D2549020903000 D2549020907600
D2549020903200 D2549020907800
D2549020903400 D2549020908000
For Myanmar Airways (MMA) use only
D2549020903600 D2549020908200
D2549020903800 D2549020908400
D2549020904000 D2549020908600
D2549020904200 D2549020908800
D2549020904400 D2549020909000
D2549020904600 D2549020909200
D2549020904800 D2549020909400
D2549020905000 D2549020909600
D2549020905200 D2549020909800
D2549020905400 D2549020910000
D2549020905600 D2549020910200
D2549020905800 D2549020910400
D2549020906000 D2549020910600
D2549020906200 D2549020910800
D2549020906400 D2549020911000
D2549020911200 D2549026000800
D2549020911400 D2549026001000
D2549020911600 D2549026001200
D2549020911800 D2549026001400
D2549020912000 D2549026001600
D2549020912200 D2549026001800
D2549020912400 D2549026002000
D2549020912600 D2549026002200
For Myanmar Airways (MMA) use only
D2549020912800 D2549026002400
D2549020913000 D2549026002600
D2549020913200 D2549026002800
D2549020913400 D2549026003000
D2549020913600 D2549026003400
D2549020913800 D2549026003600
D2549020914000 D2549026003800
D2549020914200 D2549026004000
D2549020914400 D2549026004400
D2549020914600 D2549026004600
D2549020914800 D2549026005200
D2549026000000 D2549026005600
D2549026000200 D2549030705000
D2549026000400 D2549030705400
D2549026000600 D2549030705800
D2549030706000 D2549030710600
D2549030706200 D2549030710800
D2549030706400 D2549030711200
D2549030706600 D2549030711400
D2549030706800 D2549030711600
D2549030707000 D2549030711800
D2549030707200 D2549030712000
D2549030707400 D2549030712200
For Myanmar Airways (MMA) use only
D2549030707600 D2549030712400
D2549030707800 D2549030712800
D2549030708000 D2549030713000
D2549030708200 D2549030713200
D2549030708400 D2549030713400
D2549030708600 D2549030713600
D2549030708800 D2549030713800
D2549030709000 D2549030714000
D2549030709200 D2549030714200
D2549030709400 D2549030714400
D2549030709600 D2549030714600
D2549030709800 D2549030714800
D2549030710000 D2549030800000
D2549030710200 D2549030800200
D2549030710400 D2549030800400
D2549030800800 D2549030807400
D2549030801000 D2549030807600
D2549030801200 D2549030807800
D2549030801400 D2549030808000
D2549030801600 D2549030808200
D2549030801800 D2549030808400
D2549030802000 D2549030808600
D2549030802200 D2549030808800
For Myanmar Airways (MMA) use only
D2549030802400 D2549030809000
D2549030802600 D2549030809200
D2549030802800 D2549030809400
D2549030803000 D2549030809600
D2549030803200 D2549030809800
D2549030805400 D2549030810000
D2549030805600 D2549030810200
D2549030805800 D2549030810400
D2549030806000 D2549030810600
D2549030806200 D2549030810800
D2549030806400 D2549030811000
D2549030806600 D2549030811200
D2549030806800 D2549030811400
D2549030807000 D2549030811600
D2549030807200 D2549030811800
D2549030812000 R225401196-028
D2549030812200 R225401196-030
D2549040502200 R225401196-032
D2549040502400 R225401196-072
D2549040502600 R225401196-074
D2549040502800 R225401196-076
D2549040503000 R225401196-078
D2549040503200 R225401611-002
For Myanmar Airways (MMA) use only
D2549040503400 R225401611-022
D2549040503600 R225401611-024
D2549040503800 R225401671-004
D2549040504000 R225401673-008
D2549040504200 R225401673-010
D2549040504400 R225401673-012
D2549040504600 R225401673-014
D2549040504800 R225401676-002
D2549040505000 R225401676-004
D2549040505200 R225401689-000
D2549040505400 R225401689-002
D2549040505800 R225401689-008
R225401136-002 R225401689-010
R225401149-000 R225401689-012
R225401196-026 R225401689-014
R225401689-016 R225401822-000
R225401689-018 R225401822-002
R225401689-020 R225401822-004
R225401689-022 R225401822-006
R225401691-004 R225401822-008
R225401803-004 R225401822-010
R225401803-006 R225401822-012
R225401806-000 R225401823-000
For Myanmar Airways (MMA) use only
R225401807-000 R225401823-002
R225401808-002 R225401824-000
R225401808-004 R225401824-002
R225401808-006 R225401826-000
R225401808-008 R225401826-002
R225401808-012 R225401830-002
R225401808-014 R225401830-004
R225401812-000 R225401831-000
R225401812-002 R225401831-002
R225401812-004 R225401831-004
R225401812-006 R225401831-006
R225401812-008 R225401832-000
R225401814-002 R225401832-002
R225401815-000 R225401833-000
R225401815-002 R225401833-002
R225401834-000 R225401865-000
R225401834-002 R225401866-000
R225401834-006 R225401866-002
R225401834-008 R225401869-000
R225401839-000 R225401875-000
R225401839-002 R225401877-000
R225401841-000 R225401877-002
R225401841-002 R225401880-000
For Myanmar Airways (MMA) use only
R225401842-000 R225401882-000
R225401849-000 R225401882-002
R225401856-000 R225401882-004
R225401856-002 R225401882-006
R225401856-004 R225401884-000
R225401856-006 R225401884-002
R225401860-000 R225401884-004
R225401860-002 R225401886-000
R225401860-004 R225401888-000
R225401862-000 R225401888-002
R225401862-002 R225401888-006
R225401862-004 R225401888-008
R225401862-006 R225401888-012
R225401864-000 R225401889-000
R225401864-002 R225401889-002
R225401893-000 R225411600-000
R225401893-004 R225411607-002
R225401895-000 R225411616-000
R225401895-002 R225411620-000
R225401895-006 R225411623-000
R225401896-000 R225411629-000
R225401896-002 R225411629-008
For Myanmar Airways (MMA) use only
RECORD OF REVISIONS
23 JUL 31/17
24 SEP 30/17
25 MAR 31/18
26 SEP 15/19
27 NOV 18/19
28 MAR31/20
ROR
Page 1
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
ROR
Page 2
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
RTR
Page 1
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
RTR
Page 2
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
SBL
Page 1
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
SB No. REV No. MOD No. ISSUE TITLE
DATE
A2-254-25-015 03 - Nov 30/14 INSTALLATION OF FREEZING
PROTECTION FOR LAV. A-L11,
D-L43, E-L44
A2-254-25-016 01 - Nov 30/14 INSTALLATION OF FREEZING
PROTECTION FOR LAV. A-L11,
H-L13, D-L43, E-L44
A2-254-25-025 01 - Nov 30/14 MODIFICATIONS OF LAVATORY
UNITS A-L11, D-L43, AND E-L44
A2-254-25-027 03 - Nov 30/14 MODIFICATIONS OF LAVATORY
UNITS A-L11 AND D-L43
A2-254-25-029 00 - Nov 30/14 INSTALLATION OF FREEZING
PROTECTION FOR LAV. A-L11,
D-L43, E-L44, H-L31
A2-254-25-031 00 - Nov 30/14 INSTALLATION OF FREEZING
For Myanmar Airways (MMA) use only
SBL
Page 2
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
SB No. REV No. MOD No. ISSUE TITLE
DATE
A2-254-25-058 01 - Apr 09/15 EQUIPMENT/FURNISHINGS
- LAVATORY - OXYGEN
CONTAINER ASSY
REPLACEMENT
A2-254-25-061 00 - Dec 09/14 OXYGEN MASK BOX
REPLACEMENT
A2-254-25-069 00 - Jul 08/15 EQUIPMENT/FURNISHINGS
- LAVATORY - OXYGEN
CONTAINER ASSY
REPLACEMENT
A2-254-25-070 00 - Jul 13/15 EQUIPMENT/FURNISHINGS
- LAVATORY - OXYGEN
CONTAINER ASSY
REPLACEMENT
For Myanmar Airways (MMA) use only
SBL
Page 3
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
SB No. REV No. MOD No. ISSUE TITLE
DATE
A2-254-25-086 02 - Jun 04/19 EQUIPMENT/FURNISHINGS
- LAVATORY - OXYGEN
CONTAINER ASSY
REPLACEMENT
A2-254-25-087 00 - Jul 30/15 EQUIPMENT/FURNISHINGS
- LAVATORY - OXYGEN
CONTAINER ASSY
REPLACEMENT
A2-254-25-093 00 - Aug 18/15 EQUIPMENT/FURNISHINGS
- LAVATORY - OXYGEN
CONTAINER ASSY
REPLACEMENT
A2-254-25-097 00 - Nov 17/15 EQUIPMENT/FURNISHINGS
- LAVATORY - OXYGEN
CONTAINER ASSY
For Myanmar Airways (MMA) use only
REPLACEMENT
A2-254-25-098 00 - Sep 30/15 EQUIPMENT/FURNISHINGS
- LAVATORY - OXYGEN
CONTAINER ASSY
REPLACEMENT
A2-254-25-100 00 - Jan 08/16 EQUIPMENT/FURNISHINGS
- LAVATORY - OXYGEN
CONTAINER ASSY
REPLACEMENT
A2-254-25-102 00 - Jan 05/17 EQUIPMENT/FURNISHINGS -
LAVATORY - REDECORATION
A2-254-25-103 00 - Oct 28/15 EQUIPMENT/FURNISHINGS
- LAVATORY - OXYGEN
CONTAINER ASSY
REPLACEMENT
A2-254-25-106 00 - Dec 07/15 EQUIPMENT/FURNISHINGS -
LAVATORY - MODIFICATION
AND REDECORATION
A2-254-25-106 03 - Apr 21/16 EQUIPMENT/FURNISHINGS -
LAVATORY - MODIFICATION
AND REDECORATION
A2-254-25-106 04 - Aug 05/19 EQUIPMENT/FURNISHINGS -
LAVATORY - MODIFICATION
AND REDECORATION
SBL
Page 4
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
SB No. REV No. MOD No. ISSUE TITLE
DATE
A2-254-25-111 00 - Sep 12/16 EQUIPMENT/FURNISHINGS
- LAVATORY - OXYGEN
CONTAINER ASSY
REPLACEMENT
A2-254-25-115 00 - Dec 18/15 EQUIPMENT/FURNISHINGS
- LAVATORY - OXYGEN
CONTAINER ASSY
REPLACEMENT
A2-254-25-130 00 - Mar 10/17 EQUIPMENT/FURNISHINGS -
LAVATORY - MODIFICATION
AND REDECORATION
A2-254-25-131 00 - Oct 25/16 EQUIPMENT/FURNISHINGS –
LAVATORY – REDECORATION
AND MODIFICATION
For Myanmar Airways (MMA) use only
SBL
Page 5
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
SBL
Page 6
25-41-58 Mar 31/20
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
For Myanmar Airways (MMA) use only
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
LEP
Page 38
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TABLE OF CONTENTS
Page
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .INTRO 1
DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3001
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4001
For Myanmar Airways (MMA) use only
INSPECTION/CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5001
REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6001
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7001
TOC
Page 1
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
TOC
Page 2
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
LIST OF ILLUSTRATIONS
REPAIR
6001 Repair of the Cracks or Damages in the Floor Bottom . . . . . . . . . . . . . . . . . . . . 6021
6002 Repair of the Cracks or Damages in the Vertical Panel . . . . . . . . . . . . . . . . . . . . 6022
6003 Installation of the Preventive Pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6023
6004 Broken Floor Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6024
6005 Sealant around the NTF-covering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6025
6006 Damaged Floor Pan Inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6026
LOI
Page 1
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
LOI
Page 2
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
LOI
Page 3
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
2 ATTACHMENT-LAVATORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10608
4 PANEL-CEILING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10628
LOI
Page 4
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
5 WALL-REAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10636
6 WALL-SIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10654
LOI
Page 5
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
7 HOUSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10834
LOI
Page 6
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
LOI
Page 7
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
13 PAN-FLOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11048
LOI
Page 8
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
14 LIGHT-DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11112
LOI
Page 9
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
19 CABINET-SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11244
20 TABLE-NURSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11286
LOI
Page 10
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
LOI
Page 11
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
LOI
Page 12
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
LIST OF TABLES
DISASSEMBLY
3001 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3005
3002 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3017
3003 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3018
3004 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3021
3005 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3024
3006 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3027
3007 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3029
For Myanmar Airways (MMA) use only
3008 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3031
3009 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3033
3010 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3038
3011 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3040
3012 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3042
3013 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3044
3014 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3046
3015 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3048
3016 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3050
3017 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3052
3018 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3054
3019 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3058
3020 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3061
3021 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3063
3022 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3067
3023 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3069
3024 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3072
3025 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3074
3026 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3076
3027 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3078
3028 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3080
LOT
Page 1
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
3039 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3108
3040 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3112
3041 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3114
3042 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3117
3043 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3119
3044 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3121
3045 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3123
3046 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3127
3047 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3132
3048 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3134
3049 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3136
3050 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3138
3051 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3140
3052 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3144
3053 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3146
3054 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3149
3055 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3151
3056 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3153
3057 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3155
3058 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3160
3059 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3162
LOT
Page 2
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
3070 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3187
3071 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3189
3072 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3191
3073 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3194
3074 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3198
3075 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3200
3076 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3202
3077 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3204
3078 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3206
3079 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3211
3080 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3213
3081 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3215
3082 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3217
3083 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3220
3084 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3222
3085 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3224
3086 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3226
3087 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3231
3088 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3233
3089 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3235
3090 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3237
LOT
Page 3
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
3101 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3266
3102 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3269
3103 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3271
3104 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3274
3105 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3276
3106 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3278
3107 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3280
3108 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3283
3109 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3286
3110 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3288
3111 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3293
3112 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3295
3113 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3297
3114 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3299
3115 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3303
3116 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3305
3117 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3307
3118 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3309
3119 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3312
3120 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3314
3121 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3318
LOT
Page 4
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
3132 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3342
3133 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3345
3134 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3347
3135 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3349
3136 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3351
3137 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3353
3138 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3357
3139 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3360
3140 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3362
3141 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3364
3142 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3367
3143 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3369
3144 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3371
3145 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3374
3146 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3376
3147 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3378
3148 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3380
3149 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3383
3150 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3385
3151 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3387
3152 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3391
LOT
Page 5
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
3163 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3417
3164 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3420
3165 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3424
3166 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3426
3167 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3428
3168 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3432
3169 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3434
3170 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3436
3171 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3438
3172 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3441
3173 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3443
3174 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3445
3175 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3447
3176 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3451
3177 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3453
3178 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3455
3179 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3457
3180 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3461
3181 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3463
3182 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3466
3183 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3468
LOT
Page 6
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
3194 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3496
3195 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3500
3196 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3502
3197 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3504
3198 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3508
3199 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3510
3200 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3512
3201 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3515
3202 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3519
3203 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3521
3204 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3523
3205 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3525
3206 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3531
3207 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3536
3208 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3542
3209 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3545
3210 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3550
3211 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3552
3212 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3553
3213 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3556
3214 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3560
LOT
Page 7
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
3225 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3594
3226 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3597
3227 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3599
3228 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3602
3229 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3604
3230 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3606
3231 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3609
3232 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3611
3233 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3613
3234 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3617
3235 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3619
3236 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3621
3237 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3623
3238 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3625
3239 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3629
3240 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3631
3241 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3633
3242 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3635
3243 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3638
3244 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3642
3245 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3644
LOT
Page 8
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
3256 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3691
3257 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3694
3258 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3699
3259 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3704
3260 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3707
3261 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3712
3262 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3715
3263 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3718
3264 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3721
3265 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3725
3266 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3728
3267 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3736
3268 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3737
3269 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3743
3270 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3746
3271 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3751
3272 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3755
3273 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3758
3274 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3761
3275 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3769
3276 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3776
LOT
Page 9
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
3287 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3821
3288 Reference list for the replacement of permanent installed parts ........... . . . . . . . . 3823
3289 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3842
3290 Reference list for the replacement of permanent installed parts . . . . . . . . . . . . . . 3845
CLEANING
REPAIR
6001 Decorative Foils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6004
6002 Paint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6011
6003 Replacement Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6016
6004 Replacement Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6018
6005 Replacement Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6019
6006 Replacement Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6020
6007 Riveted Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6106
6008 Placards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6111
ASSEMBLY
LOT
Page 10
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
LOT
Page 11
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
LOT
Page 12
25-41-58 Mar 31/20
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
INTRODUCTION
TASK 25-41-58-871-801-A01
1. General
(1) This manual has been prepared to show the correct procedures used in the
maintenance of a Diehl Aviation Hamburg GmbH (VC5270) manufactured lavatory.
(2) This document is written to the ATA iSpec2200 Specification and in ASD-STE100.
SI units of measurement are used in this manual with Imperial units in parentheses.
For Myanmar Airways (MMA) use only
(3) Maintenance Task Oriented Support System (MTOSS) TASK and Subtask
identification is used in this manual. The maintenance tasks and other data have
special MTOSS numbers for the use of Electronic Data Processing (EDP). The
MTOSS numbers can be ignored by the user of the manual.
(4) The manual gives maintenance on the lavatory in a workshop. It does not give
maintenance on the lavatory when it is installed on the aircraft.
(c) An with data for the lavatory's component parts. Parts are identified in all
sections of the manual by the IPL figure and item number.
TASK 25-41-58-879-801-A01
2. How to Use the Manual
A. General
(1) Make sure the manual contains the information applicable to your lavatory. Look on
the TITLE PAGE for the part number.
INTRO
Page 1
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(2) If you need to identify a part or part number, refer to the , which has an introduction
to show the procedure.
(3) The instructions in this manual must be used for all the component maintenance.
Read all the applicable WARNINGS and CAUTIONS before you do the work on
the component.
TASK 25-41-58-879-802-A01
3. Revisions and Service Bulletins
A. Manual Revisions
B. Service Bulletins
For Myanmar Airways (MMA) use only
- Service Bulletins can be issued separately. They will be included into the CMM and
IPL at the next possible revision and will be shown in the .
TASK 25-41-58-879-803-A01
4. Warnings, Cautions, Notes
(1) WARNINGS
(2) CAUTIONS
(3) NOTES
INTRO
Page 2
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-879-804-A01
5. Manufacturer
B. Contact:
Internet: www.diehl.com/aviation
TASK 25-41-58-879-807-A01
For Myanmar Airways (MMA) use only
6. Abbreviations
INTRO
Page 3
25-41-58 Sep 15/19
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
INTRO
Page 4
25-41-58 Sep 15/19
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-870-802-A01
1. General
A. The electrical system supplies the electrically operated equipment with power.
B. The potable water system supplies water to the lavatory. Quick disconnect couplings
are used for easy replacement.
F. For description and operation of these subcomponents refer to the supplier's manuals:
25-41-58 Page 1
Sep 15/19
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
ELECTRONICS GMBH
25-41-58 Page 2
Sep 15/19
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(1) Dimensions:
(2) Weights:
(a) The correct lavatory weight depends on the basic lavatory weight and the
weight of the equipment which is installed.
25-41-58 Page 3
Sep 15/19
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-870-803-A01
2. Description
(8) A washbasin
B. For installation, the lavatory has lower attachment fittings and a tie rod assembly.
E. The lavatory has a casing and a door assembly which are made of a light weight material.
F. The casing has sandwich panels made of honeycomb core with fiberglass cover plates
10 mm (0.393 in.) thick and/or 25 mm (0.984 in.) thick.
G. Special loaded areas e. g. sandwich borders and attachment points are filled with
aluminum or nylon fillers.
25-41-58 Page 4
Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
K. These parts are made of stainless steel or have stainless steel sheets:
(1) The water faucet, the waste chute, the waste flap, the ashtray and the kick strip.
25-41-58 Page 5
Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
Lavatory A
Figure 1/EN254158GRAPHIC991001A01
25-41-58 Page 6
Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-870-804-A01
3. Operation
(1) You can lock the single door assembly by a latch in the lavatory.
(2) When the single door is closed and locked, a microswitch operates the TOILET
OCCUPIED sign.
B. Fire extinguisher
(1) If there is a fire, the fire extinguisher discharges into the waste container
compartment.
For Myanmar Airways (MMA) use only
25-41-58 Page 7
Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
25-41-58 Page 8
Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-700-801-A01
1. General
A. For all Testing and Fault Isolation information refer to SPM 25-00-01. 25-00-01
For Myanmar Airways (MMA) use only
TASK 25-41-58-878-805-A01
D2549020305400 D2549030706600
1. Wiring Diagrams
Wiring Diagram
Figure 2002/EN254158GRAPHIC991003A01
Wiring Diagram
Figure 2002/EN254158GRAPHIC991003A01
TASK 25-41-58-878-805-B01
A. TBD.
TASK 25-41-58-878-805-C01
D2549020313400
3. Wiring Diagrams
TASK 25-41-58-878-806-C01
TASK 25-41-58-878-807-C01
TASK 25-41-58-878-808-C01
TASK 25-41-58-878-809-C01
TASK 25-41-58-878-810-C01
TASK 25-41-58-878-811-C01
TASK 25-41-58-878-812-C01
TASK 25-41-58-878-813-A01
Page 2032
25-41-58 Jul 31/17
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
DISASSEMBLY
TASK 25-41-58-000-801-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
B. Procedure
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-010-001-A01
(1) Removal of the Lavatory Attachment (02-1)
(a) Remove the quick release pin 02-010, the lanyard 02-110 and the strut
assembly 02-020 from the lavatory structure.
(b) Remove the quick release pin 02-010, the lanyard 02-110 and the strut
assembly 02-020 from the fitting assembly 02-100.
1 Remove the rod end 02-070 and the nut 02-030 from the strut 02-080.
2 Remove the rod end 02-050, the washer 02-040 and the nut 02-060 from
the strut 02-080.
(d) Remove the bolts 02-090 and the fitting assembly 02-100 from the lavatory
structure.
(e) Remove the bolts 02-120, the bushings 02-130, 02-140, 02-150 and the
packings 02-160.
(f) Remove the nut 02-170 and the retainer 02-180 from the lavatory structure.
(g) Remove the bolt 02-190, the washer 02-200, the bushing 02-150 and the
packing 02-160.
(h) Remove the screws 02-230, the washers 02-240, the angles 02-220 and the
lanyard 02-310 from the lavatory structure.
For Myanmar Airways (MMA) use only
(j) Remove the screw 02-320 and the lanyard 02-310 from the flap 02-210.
(k) Remove the screws 02-280, the washers 02-290, the nuts 02-300 and the
double-spring ball catches 02-330 from the angles 02-220.
(l) Remove the screws 02-260, the washers and 02-270 from the flap 02-210.
TASK 25-41-58-000-801-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-010-002-A01
(1) Removal of the Lavatory Attachment (02A-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
INSTALLED PARTS
(a) Remove the quick release pin 02A-010, the lanyard 02A-110 and the strut
assembly 02A-020 from the lavatory structure.
(b) Remove the quick release pin 02A-010, the lanyard 02A-110 and the strut
assembly 02A-020 from the fitting assembly 02A-100.
1 Remove the rod end 02A-070 and the nut 02A-030 from the strut 02A-080.
2 Remove the rod end 02A-050, the washer 02A-040 and the nut 02A-060
from the strut 02A-080.
(d) Remove the bolts 02A-090 and the fitting assembly 02A-100 from the lavatory
structure.
(e) Remove the bolts 02A-120, the bushings 02A-130, 02A-140, 02A-150 and
the packings 02A-160.
(f) Remove the nut 02A-170 and the retainer 02A-180 from the lavatory structure.
(g) Remove the bolt 02A-190, the washer 02A-200, the bushing 02A-150 and
the packing 02A-160.
(h) Remove the screws 02A-260, the washers 02A-240, the nuts 02A-270 and the
flap 02A-210 from the angles 02A-220.
(j) Remove the screws 02A-230, the washers 02A-240 and the angles 02A-220
from the lavatory structure.
TASK 25-41-58-000-801-C01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
B. Procedure
SUBTASK 25-41-58-010-003-A01
(1) Removal of the Lavatory Attachment (02B-1)
(a) Remove the quick release pin 02B-010, the lanyard 02B-110 and the strut
assembly 02B-020 from the lavatory structure.
(b) Remove the quick release pin 02B-010, the lanyard 02B-110 and the strut
assembly 02B-020 from the fitting assembly 02B-100.
1 Remove the rod end 02B-070 and the nut 02B-030 from the strut 02B-080.
2 Remove the rod end 02B-050, the washer 02B-040 and the nut 02B-060
from the strut 02B-080.
(d) Remove the bolts or screws 02B-090 and the fitting assembly 02B-100 from
the lavatory structure.
(e) Remove the bolts 02B-120, the bushings 02B-130, 02B-140, 02B-150 and
the packings 02B-160.
(f) Remove the nut 02B-170 and the retainer 02B-180 from the lavatory structure.
(g) Remove the bolt 02B-190, the washer 02B-200, the bushing 02B-150 and
the packing 02B-160.
(h) Remove the screws 02B-230, the washers 02B-240, the angles 02B-220 and
the lanyard 02B-310 from the lavatory structure.
(j) Remove the screw 02B-320 and the lanyard 02B-310 from the flap 02B-210.
For Myanmar Airways (MMA) use only
(k) Remove the screws 02B-280, the washers 02B-290, the nuts 02B-300 and the
double-spring ball catches 02B-330 from the angles 02B-220.
(l) Remove the screws 02B-260 and the washers 02B-270 from the flap 02B-210.
TASK 25-41-58-000-802-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
B. Procedure
SUBTASK 25-41-58-040-001-A01
(1) Removal and Disassembly of the Ceiling Panel (04-1)
(a) Remove the screws 04-020, 04-040, the washers 04-030 and the ceiling
assembly 04-010 from the lavatory structure.
TASK 25-41-58-000-803-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-000-104-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Table 3002
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove and disassemble the toilet switch assembly 05-090 as follows:
2 Remove the screws 05-130, the frame 05-100 and the spacer 05-140
from the rear wall assembly 05-010.
(b) Remove the screws 05-060, 05-070, the washers 05-080 and the rear wall
assembly 05-010 from the lavatory structure.
SUBTASK 25-41-58-000-104-B01
D2549020305200
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Table 3003
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove and disassemble the toilet switch assembly 05-090 as follows:
2 Remove the screws 05-130 and the frame 05-100 from the rear wall
assembly 05-010.
(b) Remove the screws 05-060, 05-070, the washers 05-080 and the rear wall
assembly 05-010 from the lavatory structure.
TASK 25-41-58-000-803-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-105-A01
(1) Removal of the Rear Wall (05A-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Front Plate
05A-
110
(a) Remove and disassemble the toilet switch assembly 05A-090 as follows:
2 Remove the screws 05A-130, the frame 05A-100 and the spacer 05A-140
from the rear wall assembly 05A-010.
(b) Remove the screws 05A-060, 05A-070, the washers 05A-080 and the rear wall
assembly 05A-010 from the lavatory structure.
(c) Remove and disassemble the plastic cup dispenser 05A-150 as follows:
1 Remove the retaining washers 05A-180 and the plastic cup dispenser
cover 05A-160.
2 Remove the tube 05A-190 from the plastic cup dispenser holder 05A-170.
3 Remove the screws 05A-200, the washers 05A-210 and the plastic cup
dispenser holder 05A-170.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-803-C01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-000-106-A01
(1) Removal of the Rear Wall (05B-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Front Plate
self adhesive
Table 3005
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove and disassemble the toilet switch assembly 05B-090 as follows:
2 Remove the screws 05B-130, the frame 05B-100 and the spacer 05B-140
from the rear wall assembly 05B-010.
(b) Remove the screws 05B-060, 05B-070, the washers 05B-080 and the rear wall
assembly 05B-010 from the lavatory structure.
TASK 25-41-58-000-804-A01
A. General
– Cleaning
– Visual Inspection
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-008-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3006
For Myanmar Airways (MMA) use only
1 Remove the security pins 06-310 from the handle assembly 06-290.
2 Remove the handle assembly 06-290 from the aft side wall assembly
06-010.
3 Remove the special screws 06-300 and the special washers 06-320 from
the aft side wall assembly 06-010.
(c) Remove the screws 06-260, the washers 06-210 and the support 06-330 from
the aft side wall assembly 06-010.
(d) Remove the studs 06-220 and the washers 06-210 from the oxygen container
assy cover 06-140.
(e) Remove the screws 06-160, the nuts 06-170 and the oxygen container assy
cover 06-140 from the angle 06-150.
(f) Remove the screws 06-200, 06-205, the washers 06-210, 06-215 and the
angle 06-150 from the aft side wall assembly 06-010.
(g) Remove the ground cable from the oxygen container assy 06-190.
(h) Remove the screws 06-200, the washers 06-210 and the oxygen container
assy 06-190 from the angles 06-180.
(j) Remove the screws 06-200, the washers 06-210 and the angles 06-180 from
the aft side wall assembly 06-010.
(k) Remove the screws 06-260, the washers 06-210 and the angle 06-340 from
the aft side wall assembly 06-010.
(l) Remove the screws 06-420 and the single door emergency unlocking device
assembly 06-350 from the post assembly 06-230.
(m) Disassemble the single door emergency unlocking device assembly 06-350 as
follows:
1 Remove the bolt 06-410 and the emergency unlocking device strike
06-370 from the emergency unlocking device housing 06-360.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the bolt 06-410.
2 Remove the pin 06-390, the snap catch 06-400 and the emergency
unlocking device pivot 06-380 from the emergency unlocking device
housing 06-360.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06-400 and the pin 06-390.
(n) Remove the caps 06-270, the screws 06-260, 06-280, the washers 06-210
and the post assembly 06-230.
1 Remove the screws 06-240 and the plates 06-255 from the post assembly
06-230.
(q) Remove the screws 06-440 and the toilet seat-cover dispenser 06-430 from the
aft side wall assembly 06-010.
(r) Remove the screws 06-040, 06-050 and the fittings 06-020, 06-030.
SUBTASK 25-41-58-010-008-B01
D2549020305200
(0) Removal of the Side Wall (06-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
PART
NAME
Table 3007
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06-310 from the handle assembly 06-290.
2 Remove the handle assembly 06-290 from the aft side wall assembly
06-010.
3 Remove the special screws 06-300 and the special washers 06-320 from
the aft side wall assembly 06-010.
(b) Remove the studs 06-220 and the washers 06-210 from the oxygen container
assy cover 06-140.
(c) Remove the screws 06-160, the nuts 06-170 and the oxygen container assy
cover 06-140 from the angle 06-150.
(d) Remove the screws 06-200, the washers 06-210 and the angle 06-150 from
the aft side wall assembly 06-010.
(e) Remove the ground cable from the oxygen container assy 06-190.
(f) Remove the screws 06-200, the washers 06-210 and the oxygen container
assy 06-190 from the angles 06-180.
(g) Remove the screws 06-200, the washers 06-210 and the angles 06-180 from
the aft side wall assembly 06-010.
(h) Remove the screws 06-260, the washers 06-210 and the angle 06-340 from
the aft side wall assembly 06-010.
(j) Remove the screws 06-420 and the single door emergency unlocking device
assembly 06-350 from the post assembly 06-230.
(k) Disassemble the single door emergency unlocking device assembly 06-350 as
follows:
For Myanmar Airways (MMA) use only
1 Remove the bolt 06-410 and the emergency unlocking device strike
06-370 from the emergency unlocking device housing 06-360.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the bolt 06-410.
2 Remove the pin 06-390, the snap catch 06-400 and the emergency
unlocking device pivot 06-380 from the emergency unlocking device
housing 06-360.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06-400 and the pin 06-390.
(l) Remove the caps 06-270, the screws 06-260, 06-280, the washers 06-210
and the post assembly 06-230.
1 Remove the screws 06-240 and the plates 06-255 from the post assembly
06-230.
(n) Remove the screws 06-440 and the toilet seat-cover dispenser 06-430 from the
aft side wall assembly 06-010.
(p) Remove the screws 06-040, 06-050 and the fittings 06-020, 06-030.
SUBTASK 25-41-58-010-008-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
For Myanmar Airways (MMA) use only
Table 3008
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06-310 from the handle assembly 06-290.
2 Remove the handle assembly 06-290 from the aft side wall assembly
06-010.
3 Remove the special screws 06-300 and the special washers 06-320 from
the aft side wall assembly 06-010.
(b) Remove the screws 06-260, the washers 06-210 and the support 06-330 from
the aft side wall assembly 06-010.
(c) Remove the studs 06-220 and the washers 06-210 from the oxygen container
assy cover 06-140.
(d) Remove the screws 06-160, the nuts 06-170 and the oxygen container assy
cover 06-140 from the angle 06-150.
(e) Remove the screws 06-200, the washers 06-210 and the angle 06-150 from
the aft side wall assembly 06-010.
(f) Remove the ground cable from the oxygen container assy06-190.
(g) Remove the screws 06-200, the washers 06-210 and the oxygen container
assy 06-190 from the angles 06-180.
(h) Remove the screws 06-200, the washers 06-210 and the angles 06-180 from
the aft side wall assembly 06-010.
(j) Remove the screws 06-260, the washers 06-210 and the angle 06-340 from
the aft side wall assembly 06-010.
For Myanmar Airways (MMA) use only
(k) Remove the screws 06-420 and the single door emergency unlocking device
assembly 06-350 from the post assembly 06-230.
(l) Disassemble the single door emergency unlocking device assembly 06-350 as
follows:
1 Remove the bolt 06-410 and the emergency unlocking device strike
06-370 from the emergency unlocking device housing 06-360.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the bolt 06-410.
2 Remove the pin 06-390, the snap catch 06-400 and the emergency
unlocking device pivot 06-380 from the emergency unlocking device
housing 06-360.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06-400 and the pin 06-390.
(m) Remove the caps 06-270, the screws 06-260, 06-280, the washers 06-210
and the post assembly 06-230.
1 Remove the screws 06-240 and the plates 06-255 from the post assembly
06-230.
(o) Remove the screws 06-040, 06-050 and the fittings 06-020, 06-030.
SUBTASK 25-41-58-010-008-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3009
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06-310 from the handle assembly 06-290.
2 Remove the handle assembly 06-290 from the aft side wall assembly
06-010.
3 Remove the special screws 06-300 and the special washers 06-320 from
the aft side wall assembly 06-010.
(b) Remove the screws 06-260, the washers 06-210 and the support 06-330 from
the aft side wall assembly 06-010.
(c) Remove the studs 06-220 and the washers 06-210 from the oxygen container
assy cover 06-140.
(d) Remove the screws 06-160, the nuts 06-170 and the oxygen container assy
cover 06-140 from the angle 06-150.
(e) Remove the screws 06-200, the washers 06-210 and the angle 06-150 from
the aft side wall assembly 06-010.
(f) Remove the ground cable from the oxygen container assy 06-190.
(g) Remove the screws 06-200, 06-205, the washers 06-210 and the oxygen
container assy 06-190 from the angles 06-180.
(h) Remove the screws 06-200, the washers 06-210 and the angles 06-180 from
the aft side wall assembly 06-010.
For Myanmar Airways (MMA) use only
(j) Remove the screws 06-260, the washers 06-210 and the angle 06-340 from
the aft side wall assembly 06-010.
(k) Remove the screws 06-420 and the single door emergency unlocking device
assembly 06-350 from the post assembly 06-230.
(l) Disassemble the single door emergency unlocking device assembly 06-350 as
follows:
1 Remove the bolt 06-410 and the emergency unlocking device strike
06-370 from the emergency unlocking device housing 06-360.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the bolt 06-410.
2 Remove the pin 06-390, the snap catch 06-400 and the emergency
unlocking device pivot 06-380 from the emergency unlocking device
housing 06-360.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06-400 and the pin 06-390.
(m) Remove the caps 06-270, the screws 06-260, 06-280, the washers 06-210
and the post assembly 06-230.
1 Remove the screws 06-240 and the plates 06-255 from the post assembly
06-230.
(o) Remove the screws 06-440 and the toilet seat-cover dispenser 06-430 from the
aft side wall assembly 06-010.
For Myanmar Airways (MMA) use only
(p) Remove the screws 06-040, 06-050 and the fittings 06-020, 06-030.
TASK 25-41-58-000-804-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-009-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3010
For Myanmar Airways (MMA) use only
1 Remove the security pins 06A-160 from the handle assemblies 06A-140.
2 Remove the handle assemblies 06A-140 from the aft side wall assembly
06A-010.
3 Remove the special screws 06A-150 and the special washers 06A-170
from the aft side wall assembly 06A-010.
(b) Remove the studs 06A-260 and the washers 06A-250 from the oxygen
container assy cover 06A-180.
(c) Remove the screws 06A-200, the nuts 06A-210 and the oxygen container assy
cover 06A-180 from the angle 06A-190.
(d) Remove the screws 06A-240, the washers 06A-250 and the angle 06A-190
from the aft side wall assembly 06A-010.
(e) Remove the ground cable from the oxygen container assy 06A-230.
(f) Remove the screws 06A-240, the washers 06A-250 and the oxygen container
assy 06A-230 from the angles 06A-220.
(g) Remove the screws 06A-240, the washers 06A-250 and the angles 06A-220
from the aft side wall assembly 06A-010.
(h) Remove the screws 06A-300, the washers 06A-250 and the angle 06A-350
from the aft side wall assembly 06A-010.
(j) Remove the screws 06A-360 and the single door emergency unlocking device
assembly 06A-370 from the post assembly 06A-270.
(k) Disassemble the single door emergency unlocking device assembly 06A-370
as follows:
1 Remove the bolt 06A-430 and the emergency unlocking device strike
06A-390 from the emergency unlocking device housing 06A-380.
For Myanmar Airways (MMA) use only
2 Remove the pin 06A-410, the snap catch 06A-420 and the emergency
unlocking device pivot 06A-400 from the emergency unlocking device
housing 06A-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06A-420 and the pin 06A-410.
(l) Remove the caps 06A-310, the screws 06A-300, 06A-320, the washers
06A-250 and the post assembly 06A-270.
1 Remove the screws 06A-280 and the plates 06A-295 from the post
assembly 06A-270.
(n) Remove the screws 06A-040, 06A-050 and the fittings 06A-020, 06A-030.
SUBTASK 25-41-58-010-009-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3011
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06A-160 from the handle assemblies 06A-140.
2 Remove the handle assemblies 06A-140 from the aft side wall assembly
06A-010.
3 Remove the special screws 06A-150 and the special washers 06A-170
from the aft side wall assembly 06A-010.
(b) Remove the studs 06A-260 and the washers 06A-250 from the oxygen
container assy cover 06A-180.
(c) Remove the screws 06A-200, the nuts 06A-210 and the oxygen container assy
cover 06A-180 from the angle 06A-190.
(d) Remove the screws 06A-240, the washers 06A-250 and the angle 06A-190
from the aft side wall assembly 06A-010.
(e) Remove the ground cable from the oxygen container assy 06A-230.
(f) Remove the screws 06A-240, 06A-245, the washers 06A-250 and the oxygen
container assy 06A-230 from the angles 06A-220.
(g) Remove the screws 06A-240, the washers 06A-250 and the angles 06A-220
from the aft side wall assembly 06A-010.
(h) Remove the screws 06A-300, the washers 06A-250 and the angle 06A-350
from the aft side wall assembly 06A-010.
(j) Remove the screws 06A-360 and the single door emergency unlocking device
assembly 06A-370 from the post assembly 06A-270.
(k) Disassemble the single door emergency unlocking device assembly 06A-370
as follows:
1 Remove the bolt 06A-430 and the emergency unlocking device strike
06A-390 from the emergency unlocking device housing 06A-380.
2 Remove the pin 06A-410, the snap catch 06A-420 and the emergency
unlocking device pivot 06A-400 from the emergency unlocking device
housing 06A-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06A-420 and the pin 06A-410.
(l) Remove the caps 06A-310, the screws 06A-300, 06A-320, the washers
06A-250 and the post assembly 06A-270.
1 Remove the screws 06A-280 and the plates 06A-295 from the post
assembly 06A-270.
(n) Remove the screws 06A-040, 06A-050 and the fittings 06A-020, 06A-030.
SUBTASK 25-41-58-010-009-C01
D2549020301400
(0) Removal of the Side Wall (06A-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Assembly 350-802-A01
Table 3012
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06A-160 from the handle assemblies 06A-140.
2 Remove the handle assemblies 06A-140 from the aft side wall assembly
06A-010.
3 Remove the special screws 06A-150 and the special washers 06A-170
from the aft side wall assembly 06A-010.
(b) Remove the studs 06A-260 and the washers 06A-250 from the oxygen
container assy cover 06A-180.
(c) Remove the screws 06A-200, the nuts 06A-210 and the oxygen container assy
cover 06A-180 from the angle 06A-190.
(d) Remove the screws 06A-240, the washers 06A-250 and the angle 06A-190
from the aft side wall assembly 06A-010.
(e) Remove the ground cable from the oxygen container assy 06A-230.
(f) Remove the screws 06A-240, the washers 06A-250 and the oxygen container
assy 06A-230 from the angles 06A-220.
(g) Remove the screws 06A-240, the washers 06A-250 and the angles 06A-220
from the aft side wall assembly 06A-010.
(h) Remove the screws 06A-300, the washers 06A-250 and the angle 06A-350
from the aft side wall assembly 06A-010.
(j) Remove the screws 06A-360 and the single door emergency unlocking device
assembly 06A-370 from the post assembly 06A-270.
(k) Disassemble the single door emergency unlocking device assembly 06A-370
as follows:
1 Remove the bolt 06A-430 and the emergency unlocking device strike
06A-390 from the emergency unlocking device housing 06A-380.
2 Remove the pin 06A-410, the snap catch 06A-420 and the emergency
unlocking device pivot 06A-400 from the emergency unlocking device
housing 06A-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06A-420 and the pin 06A-410.
(l) Remove the caps 06A-310, the screws 06A-300, 06A-320, the washers
06A-250 and the post assembly 06A-270.
1 Remove the screws 06A-280 and the plates 06A-295 from the post
assembly 06A-270.
(n) Remove the screws 06A-040, 06A-050 and the fittings 06A-020, 06A-030.
SUBTASK 25-41-58-010-009-E01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3013
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the setscrews 06A-480 and the handle 06A-450 from the screws
06A-460.
2 Remove the screws 06A-460 and the washers 06A-470 from the aft side
wall assembly 06A-010.
(b) Remove the studs 06A-260 and the washers 06A-250 from the oxygen
container assy cover 06A-180.
(c) Remove the screws 06A-200, the nuts 06A-210 and the oxygen container assy
cover 06A-180 from the angle 06A-190.
(d) Remove the screws 06A-240, the washers 06A-250 and the angle 06A-190
from the aft side wall assembly 06A-010.
(e) Remove the ground cable from the oxygen container assy 06A-230.
(f) Remove the screws 06A-240, the washers 06A-250 and the oxygen container
assy 06A-230 from the angles 06A-220.
(g) Remove the screws 06A-240, the washers 06A-250 and the angles 06A-220
from the aft side wall assembly 06A-010.
(h) Remove the screws 06A-300, the washers 06A-250 and the angle 06A-350
from the aft side wall assembly 06A-010.
(j) Remove the screws 06A-360 and the single door emergency unlocking device
assembly 06A-370 from the post assembly 06A-270.
(k) Disassemble the single door emergency unlocking device assembly 06A-370
as follows:
1 Remove the bolt 06A-430 and the emergency unlocking device strike
06A-390 from the emergency unlocking device housing 06A-380.
2 Remove the pin 06A-410, the snap catch 06A-420 and the emergency
unlocking device pivot 06A-400 from the emergency unlocking device
housing 06A-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06A-420 and the pin 06A-410.
(l) Remove the caps 06A-310, the screws 06A-300, 06A-320, the washers
06A-250 and the post assembly 06A-270.
1 Remove the screws 06A-280 and the plates 06A-295 from the post
assembly 06A-270.
(n) Remove the screws 06A-040, 06A-050 and the fittings 06A-020, 06A-030.
SUBTASK 25-41-58-010-009-F01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3014
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06A-160 from the handle assemblies 06A-140.
2 Remove the handle assemblies 06A-140 from the aft side wall assembly
06A-010.
3 Remove the special screws 06A-150 and the special washers 06A-170
from the aft side wall assembly 06A-010.
(b) Remove the studs 06A-260 and the washers 06A-250 from the oxygen
container assy cover 06A-180.
(c) Remove the screws 06A-200, the nuts 06A-210 and the oxygen container assy
cover 06A-180 from the angle 06A-190.
(d) Remove the screws 06A-240, the washers 06A-250 and the angle 06A-190
from the aft side wall assembly 06A-010.
(e) Remove the ground cable from the oxygen container assy 06A-230.
(f) Remove the screws 06A-240, 06A-245, the washers 06A-250 and the oxygen
container assy 06A-230 from the angles 06A-220.
(g) Remove the screws 06A-240, the washers 06A-250 and the angles 06A-220
from the aft side wall assembly 06A-010.
(h) Remove the screws 06A-300, the washers 06A-250 and the angle 06A-350
from the aft side wall assembly 06A-010.
(j) Remove the screws 06A-360 and the single door emergency unlocking device
assembly 06A-370 from the post assembly 06A-270.
(k) Disassemble the single door emergency unlocking device assembly 06A-370
as follows:
1 Remove the bolt 06A-430 and the emergency unlocking device strike
06A-390 from the emergency unlocking device housing 06A-380.
2 Remove the pin 06A-410, the snap catch 06A-420 and the emergency
unlocking device pivot 06A-400 from the emergency unlocking device
housing 06A-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06A-420 and the pin 06A-410.
(l) Remove the caps 06A-310, the screws 06A-300, 06A-305, 06A-320, the
washers 06A-250 and the post assembly 06A-270.
1 Remove the screws 06A-280 and the plates 06A-295 from the post
assembly 06A-270.
(n) Remove the screws 06A-340 and the toilet seat-cover dispenser 06A-330 from
the aft side wall assembly 06A-010.
(p) Remove the screws 06A-040, 06A-050 and the fittings 06A-020, 06A-030.
SUBTASK 25-41-58-010-009-G01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
PART
NAME
Table 3015
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06A-160 from the handle assemblies 06A-140.
2 Remove the handle assemblies 06A-140 from the aft side wall assembly
06A-010.
3 Remove the special screws 06A-150 and the special washers 06A-170
from the aft side wall assembly 06A-010.
(b) Remove the studs 06A-260 and the washers 06A-250 from the oxygen
container assy cover 06A-180.
(c) Remove the screws 06A-200, the nuts 06A-210 and the oxygen container assy
cover 06A-180 from the angle 06A-190.
(d) Remove the screws 06A-240, the washers 06A-250 and the angle 06A-190
from the aft side wall assembly 06A-010.
(e) Remove the ground cable from the oxygen container assy 06A-230.
(f) Remove the screws 06A-240, the washers 06A-250 and the oxygen container
assy 06A-230 from the angles 06A-220.
(g) Remove the screws 06A-240, the washers 06A-250 and the angles 06A-220
from the aft side wall assembly 06A-010.
(h) Remove the screws 06A-300, the washers 06A-250 and the angle 06A-350
from the aft side wall assembly 06A-010.
(j) Remove the screws 06A-360 and the single door emergency unlocking device
assembly 06A-370 from the post assembly 06A-270.
(k) Disassemble the single door emergency unlocking device assembly 06A-370
as follows:
For Myanmar Airways (MMA) use only
1 Remove the bolt 06A-430 and the emergency unlocking device strike
06A-390 from the emergency unlocking device housing 06A-380.
2 Remove the pin 06A-410, the snap catch 06A-420 and the emergency
unlocking device pivot 06A-400 from the emergency unlocking device
housing 06A-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06A-420 and the pin 06A-410.
(l) Remove the caps 06A-310, the screws 06A-300, 06A-320, the washers
06A-250 and the post assembly 06A-270.
1 Remove the screws 06A-280 and the plates 06A-295 from the post
assembly 06A-270.
(n) Remove the screws 06A-340 and the toilet seat-cover dispenser 06A-330 from
the aft side wall assembly 06A-010.
(p) Remove the screws 06A-040, 06A-050 and the fittings 06A-020, 06A-030.
SUBTASK 25-41-58-010-009-J01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
For Myanmar Airways (MMA) use only
Table 3016
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06A-160 from the handle assemblies 06A-140.
2 Remove the handle assemblies 06A-140 from the aft side wall assembly
06A-010.
3 Remove the special screws 06A-150 and the special washers 06A-170
from the aft side wall assembly 06A-010.
(b) Remove the studs 06A-260 and the washers 06A-250 from the oxygen
container assy cover 06A-180.
(c) Remove the screws 06A-200, the nuts 06A-210 and the oxygen container assy
cover 06A-180 from the angle 06A-190.
(d) Remove the screws 06A-240, the washers 06A-250 and the angle 06A-190
from the aft side wall assembly 06A-010.
(e) Remove the ground cable from the oxygen container assy 06A-230.
(f) Remove the screws 06A-240, 06A-245, the washers 06A-250 and the oxygen
container assy 06A-230 from the angles 06A-220.
(g) Remove the screws 06A-240, the washers 06A-250 and the angles 06A-220
from the aft side wall assembly 06A-010.
(h) Remove the screws 06A-300, the washers 06A-250 and the angle 06A-350
from the aft side wall assembly 06A-010.
(j) Remove the screws 06A-360 and the single door emergency unlocking device
assembly 06A-370 from the post assembly 06A-270.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06A-370
as follows:
1 Remove the bolt 06A-430 and the emergency unlocking device strike
06A-390 from the emergency unlocking device housing 06A-380.
2 Remove the pin 06A-410, the snap catch 06A-420 and the emergency
unlocking device pivot 06A-400 from the emergency unlocking device
housing 06A-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06A-420 and the pin 06A-410.
(l) Remove the caps 06A-310, the screws 06A-300, 06A-320, the washers
06A-250 and the post assembly 06A-270.
1 Remove the screws 06A-280 and the plates 06A-295 from the post
assembly 06A-270.
(n) Remove the screw 06A-361 and the coat hook 06A-530 from the aft side wall
assembly 06A-010.
(p) Remove the screws 06A-040, 06A-050 and the fittings 06A-020, 06A-030.
SUBTASK 25-41-58-010-009-K01
D2549030706000
(0) Removal of the Side Wall (06A-1)
NOTE: See TABLE for the references for the replacement procedures of
For Myanmar Airways (MMA) use only
Table 3017
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06A-160 from the handle assemblies 06A-140.
2 Remove the handle assemblies 06A-140 from the aft side wall assembly
06A-010.
3 Remove the special screws 06A-150 and the special washers 06A-170
from the aft side wall assembly 06A-010.
(b) Remove the studs 06A-260 and the washers 06A-250 from the oxygen
container assy cover 06A-180.
(c) Remove the screws 06A-200, the nuts 06A-210 and the oxygen container assy
cover 06A-180 from the angle 06A-190.
(d) Remove the screws 06A-240, the washers 06A-250 and the angle 06A-190
from the aft side wall assembly 06A-010.
(e) Remove the screws 06A-500, the washers 06A-510, the clamps 06A-520 and
the hose 06A-490 from the aft side wall assembly 06A-010.
(f) Remove the hose 06A-490 from the oxygen container assy 06A-230.
(g) Remove the ground cable from the oxygen container assy 06A-230.
(h) Remove the screws 06A-240, the washers 06A-250 and the oxygen container
assy 06A-230 from the angles 06A-220.
For Myanmar Airways (MMA) use only
(j) Remove the screws 06A-240, the washers 06A-250 and the angles 06A-220
from the aft side wall assembly 06A-010.
(k) Remove the screws 06A-300, the washers 06A-250 and the angle 06A-350
from the aft side wall assembly 06A-010.
(l) Remove the screws 06A-360 and the single door emergency unlocking device
assembly 06A-370 from the post assembly 06A-270.
(m) Disassemble the single door emergency unlocking device assembly 06A-370
as follows:
1 Remove the bolt 06A-430 and the emergency unlocking device strike
06A-390 from the emergency unlocking device housing 06A-380.
2 Remove the pin 06A-410, the snap catch 06A-420 and the emergency
unlocking device pivot 06A-400 from the emergency unlocking device
housing 06A-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06A-420 and the pin 06A-410.
(n) Remove the caps 06A-310, the screws 06A-300, 06A-320, the washers
06A-250 and the post assembly 06A-270.
1 Remove the screws 06A-280 and the plates 06A-295 from the post
assembly 06A-270.
(q) Remove the screws 06A-340 and the toilet seat-cover dispenser 06A-330 from
the aft side wall assembly 06A-010.
For Myanmar Airways (MMA) use only
(r) Remove the screws 06A-040, 06A-050 and the fittings 06A-020, 06A-030.
SUBTASK 25-41-58-010-009-L01
D2549030706400 D2549030714000
(0) Removal of the Side Wall (06A-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3018
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06A-160 from the handle assemblies 06A-140.
2 Remove the handle assemblies 06A-140 from the aft side wall assembly
06A-010.
3 Remove the special screws 06A-150 and the special washers 06A-170
from the aft side wall assembly 06A-010.
(b) Remove the studs 06A-260 and the washers 06A-250 from the oxygen
container assy cover 06A-180.
(c) Remove the screws 06A-200, the nuts 06A-210 and the oxygen container assy
cover 06A-180 from the angle 06A-190.
(d) Remove the screws 06A-240, the washers 06A-250 and the angle 06A-190
from the aft side wall assembly 06A-010.
(e) Remove the screws 06A-500, the washers 06A-510, the clamps 06A-520 and
For Myanmar Airways (MMA) use only
the hose 06A-490 from the aft side wall assembly 06A-010.
(f) Remove the hose 06A-490 from the oxygen container assy 06A-230.
(g) Remove the ground cable from the oxygen container assy 06A-230.
(h) Remove the screws 06A-240, the washers 06A-250 and the oxygen container
assy 06A-230 from the angles 06A-220.
(j) Remove the screws 06A-240, the washers 06A-250 and the angles 06A-220
from the aft side wall assembly 06A-010.
(k) Remove the screws 06A-300, the washers 06A-250 and the angle 06A-350
from the aft side wall assembly 06A-010.
(l) Remove the screws 06A-360 and the single door emergency unlocking device
assembly 06A-370 from the post assembly 06A-270.
(m) Disassemble the single door emergency unlocking device assembly 06A-370
as follows:
1 Remove the bolt 06A-430 and the emergency unlocking device strike
06A-390 from the emergency unlocking device housing 06A-380.
2 Remove the pin 06A-410, the snap catch 06A-420 and the emergency
unlocking device pivot 06A-400 from the emergency unlocking device
housing 06A-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
For Myanmar Airways (MMA) use only
(n) Remove the caps 06A-310, the screws 06A-300, 06A-320, the washers
06A-250 and the post assembly 06A-270.
1 Remove the screws 06A-280 and the plates 06A-295 from the post
assembly 06A-270.
(q) Remove the screws 06A-340 and the toilet seat-cover dispenser 06A-330 from
the aft side wall assembly 06A-010.
(r) Remove the screw 06A-361 and the coat hook 06A-530 from the aft side wall
assembly 06A-010.
(s) Remove the screws 06A-040, 06A-050 and the fittings 06A-020, 06A-030.
TASK 25-41-58-000-804-C01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-010-A01
For Myanmar Airways (MMA) use only
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
1 Remove the security pins 06B-160 from the handle assemblies 06B-140.
2 Remove the handle assemblies 06B-140 from the aft side wall assembly
06B-010.
3 Remove the special screws 06B-150 and the special washers 06B-170
from the aft side wall assembly 06B-010.
(b) Remove the studs 06B-260 and the washers 06B-250 from the oxygen
container assy cover 06B-180.
(c) Remove the screws 06B-200, the nuts 06B-210 and the oxygen container assy
cover 06B-180 from the angle 06B-190.
(d) Remove the screws 06B-240, the washers 06B-250 and the angle 06B-190
from the aft side wall assembly 06B-010.
For Myanmar Airways (MMA) use only
(e) Remove the ground cable from the oxygen container assy 06B-230.
(f) Remove the screws 06B-240, 06B-245, the washers 06B-250 and the oxygen
container assy 06B-230 from the angles 06B-220.
(g) Remove the screws 06B-240, the washers 06B-250 and the angles 06B-220
from the aft side wall assembly 06B-010.
(h) Remove the screws 06B-300, the washers 06B-250 and the angle 06B-350
from the aft side wall assembly 06B-010.
(j) Remove the screws 06B-430 and the single door emergency unlocking device
assembly 06B-360 from the post assembly 06B-270.
(k) Disassemble the single door emergency unlocking device assembly 06B-360
as follows:
1 Remove the bolt 06B-420 and the emergency unlocking device strike
06B-380 from the emergency unlocking device housing 06B-370.
2 Remove the pin 06B-400, the snap catch 06B-410 and the emergency
unlocking device pivot 06B-390 from the emergency unlocking device
housing 06B-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06B-410 and the pin 06B-400.
(l) Remove the caps 06B-310, the screws 06B-300, 06B-320, the washers
06B-250 and the post assembly 06B-270.
1 Remove the screws 06B-280 and the plates 06B-295 from the post
assembly 06B-270.
(n) Remove the screws 06B-340 and the toilet seat-cover dispenser 06B-330 from
the aft side wall assembly 06B-010.
(p) Remove the mirror assembly 06B-450 from the screws 06B-340.
(q) Remove the screws 06B-340, 06B-475 and the washers 06B-477 from the aft
side wall assembly 06B-010.
(r) Remove the screws 06B-200 and the section 06B-440 from the aft side wall
assembly 06B-010.
(s) Remove the screws 06B-040, 06B-050 and the fittings 06B-020, 06B-030.
SUBTASK 25-41-58-010-010-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
1 Remove the security pins 06B-160 from the handle assemblies 06B-140.
2 Remove the handle assemblies 06B-140 from the aft side wall assembly
06B-010.
3 Remove the special screws 06B-150 and the special washers 06B-170
from the aft side wall assembly 06B-010.
(b) Remove the studs 06B-260 and the washers 06B-250 from the oxygen
container assy cover 06B-180.
(c) Remove the screws 06B-200, the nuts 06B-210 and the oxygen container assy
cover 06B-180 from the angle 06B-190.
(d) Remove the screws 06B-240, the washers 06B-250 and the angle 06B-190
from the aft side wall assembly 06B-010.
(e) Remove the ground cable from the oxygen container assy 06B-230.
(f) Remove the screws 06B-240, 06B-245, the washers 06B-250 and the oxygen
container assy 06B-230 from the angles 06B-220.
(g) Remove the screws 06B-240, the washers 06B-250 and the angles 06B-220
from the aft side wall assembly 06B-010.
(h) Remove the screws 06B-300, the washers 06B-250 and the angle 06B-350
from the aft side wall assembly 06B-010.
(j) Remove the screws 06B-430 and the single door emergency unlocking device
assembly 06B-360 from the post assembly 06B-270.
(k) Disassemble the single door emergency unlocking device assembly 06B-360
as follows:
1 Remove the bolt 06B-420 and the emergency unlocking device strike
06B-380 from the emergency unlocking device housing 06B-370.
2 Remove the pin 06B-400, the snap catch 06B-410 and the emergency
unlocking device pivot 06B-390 from the emergency unlocking device
housing 06B-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06B-410 and the pin 06B-400.
(l) Remove the screws 06B-300, 06B-320, the washers 06B-250 and the post
assembly 06B-270.
1 Remove the screws 06B-280 and the plates 06B-295 from the post
assembly 06B-270.
(o) Remove the screws 06B-340 and the toilet seat-cover dispenser 06B-330 from
the aft side wall assembly 06B-010.
(p) Remove the mirror assembly 06B-450 from the screws 06B-340.
(q) Remove the screws 06B-340, 06B-475 and the washers 06B-477 from the aft
side wall assembly 06B-010.
(r) Remove the screws 06B-200 and the section 06B-440 from the aft side wall
assembly 06B-010.
For Myanmar Airways (MMA) use only
(s) Remove the screws 06B-040, 06B-050 and the fittings 06B-020, 06B-030.
SUBTASK 25-41-58-010-010-C01
D2549010414600
(0) Removal of the Side Wall (06B-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
1 Remove the security pins 06B-160 from the handle assemblies 06B-140.
2 Remove the handle assemblies 06B-140 from the aft side wall assembly
06B-010.
3 Remove the special screws 06B-150 and the special washers 06B-170
from the aft side wall assembly 06B-010.
(b) Remove the studs 06B-260 and the washers 06B-250 from the oxygen
container assy cover 06B-180.
(c) Remove the screws 06B-200, the nuts 06B-210 and the oxygen container assy
cover 06B-180 from the angle 06B-190.
For Myanmar Airways (MMA) use only
(d) Remove the screws 06B-240, the washers 06B-250 and the angle 06B-190
from the aft side wall assembly 06B-010.
(e) Remove the ground cable from the oxygen container assy 06B-230.
(f) Remove the screws 06B-240, the washers 06B-250 and the oxygen container
assy 06B-230 from the angles 06B-220.
(g) Remove the screws 06B-240, the washers 06B-250 and the angles 06B-220
from the aft side wall assembly 06B-010.
(h) Remove the screws 06B-300, the washers 06B-250 and the angle 06B-350
from the aft side wall assembly 06B-010.
(j) Remove the screws 06B-430 and the single door emergency unlocking device
assembly 06B-360 from the post assembly 06B-270.
(k) Disassemble the single door emergency unlocking device assembly 06B-360
as follows:
1 Remove the bolt 06B-420 and the emergency unlocking device strike
06B-380 from the emergency unlocking device housing 06B-370.
2 Remove the pin 06B-400, the snap catch 06B-410 and the emergency
unlocking device pivot 06B-390 from the emergency unlocking device
housing 06B-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
For Myanmar Airways (MMA) use only
(l) Remove the screws 06B-300, 06B-320, the washers 06B-250 and the post
assembly 06B-270.
1 Remove the screws 06B-280 and the plates 06B-295 from the post
assembly 06B-270.
(o) Remove the screws 06B-340 and the toilet seat-cover dispenser 06B-330 from
the aft side wall assembly 06B-010.
(p) Remove the mirror assembly 06B-450 from the screws 06B-340.
(q) Remove the screws 06B-340, 06B-475 and the washers 06B-477 from the aft
side wall assembly 06B-010.
(r) Remove the screws 06B-200 and the section 06B-440 from the aft side wall
assembly 06B-010.
(s) Remove the screws 06B-040, 06B-050 and the fittings 06B-020, 06B-030.
TASK 25-41-58-000-804-D01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-011-A01
For Myanmar Airways (MMA) use only
D2549030801200
(1) Removal of the Side Wall (06C-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3022
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(b) Remove the studs 06C-260 and the washers 06C-250 from the oxygen
container assy cover 06C-180.
(c) Remove the screws 06C-200, the nuts 06C-210 and the oxygen container assy
cover 06C-180 from the angle 06C-190.
(d) Remove the screws 06C-240, the washers 06C-250 and the angle 06C-190
from the aft side wall assembly 06C-010.
(e) Remove the ground cable from the oxygen container assy 06C-230.
(f) Remove the screws 06C-240, the washers 06C-250 and the oxygen container
assy 06C-230 from the angles 06C-220.
(g) Remove the screws 06C-240, the washers 06C-250 and the angles 06C-220
from the aft side wall assembly 06C-010.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06C-310, the washers 06C-250 and the angle 06C-360
from the aft side wall assembly 06C-010.
(j) Remove the screws 06C-371 and the single door emergency unlocking device
assembly 06C-380 from the post assembly 06C-270.
(k) Disassemble the single door emergency unlocking device assembly 06C-380
as follows:
1 Remove the bolt 06C-440 and the emergency unlocking device strike
06C-400 from the emergency unlocking device housing 06C-390.
2 Remove the pin 06C-420, the snap catch 06C-430 and the emergency
unlocking device pivot 06C-410 from the emergency unlocking device
housing 06C-390.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06C-430 and the pin 06C-420.
(l) Remove the caps 06C-320, the screws 06C-310, 06C-330, the washers
06C-250 and the post assembly 06C-270.
1 Remove the screws 06C-280 and the plates 06C-300 from the post
assembly 06C-270.
(n) Remove the screws 06C-040, 06C-050 and the fittings 06C-020, 06C-030.
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-010-011-B01
D2549030709000
(0) Removal of the Side Wall (06C-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3023
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06C-160 from the handle assemblies 06C-140.
2 Remove the handle assemblies 06C-140 from the aft side wall assembly
06C-010.
3 Remove the special screws 06C-150 and the special washers 06C-170
from the aft side wall assembly 06C-010.
(b) Remove the studs 06C-260 and the washers 06C-250 from the oxygen
container assy cover 06C-180.
(c) Remove the screws 06C-200, the nuts 06C-210 and the oxygen container assy
cover 06C-180 from the angle 06C-190.
(d) Remove the screws 06C-240, the washers 06C-250 and the angle 06C-190
from the aft side wall assembly 06C-010.
(e) Remove the screws 06C-460, the washers 06C-470, the clamps 06C-480 and
the hose 06C-450 from the aft side wall assembly 06C-010.
(f) Remove the hose 06C-450 from the oxygen container assy 06C-230.
For Myanmar Airways (MMA) use only
(g) Remove the ground cable from the oxygen container assy 06C-230.
(h) Remove the screws 06C-240, the washers 06C-250 and the oxygen container
assy 06C-230 from the angles 06C-220.
(j) Remove the screws 06C-240, the washers 06C-250 and the angles 06C-220
from the aft side wall assembly 06C-010.
(k) Remove the screws 06C-310, the washers 06C-250 and the angle 06C-360
from the aft side wall assembly 06C-010.
(l) Remove the screws 06C-370 and the single door emergency unlocking device
assembly 06C-380 from the post assembly 06C-270.
(m) Disassemble the single door emergency unlocking device assembly 06C-380
as follows:
1 Remove the bolt 06C-440 and the emergency unlocking device strike
06C-400 from the emergency unlocking device housing 06C-390.
2 Remove the pin 06C-420, the snap catch 06C-430 and the emergency
unlocking device pivot 06C-410 from the emergency unlocking device
housing 06C-390.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06C-430 and the pin 06C-420.
(n) Remove the caps 06C-320, the screws 06C-310, 06C-330, the washers
06C-250 and the post assembly 06C-270.
1 Remove the screws 06C-280 and the plates 06C-300 from the post
assembly 06C-270.
(q) Remove the screws 06C-350 and the toilet seat-cover dispenser 06C-340 from
the aft side wall assembly 06C-010.
(r) Remove the screw 06C-370 and the coat hook 06C-490 from the aft side wall
assembly 06C-010.
(s) Remove the screws 06C-040, 06C-050 and the fittings 06C-020, 06C-030.
SUBTASK 25-41-58-010-011-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3024
For Myanmar Airways (MMA) use only
1 Remove the security pins 06C-160 from the handle assemblies 06C-140.
2 Remove the handle assemblies 06C-140 from the aft side wall assembly
06C-010.
3 Remove the special screws 06C-150 and the special washers 06C-170
from the aft side wall assembly 06C-010.
(b) Remove the studs 06C-260 and the washers 06C-250 from the oxygen
container assy cover 06C-180.
(c) Remove the screws 06C-200, the nuts 06C-210 and the oxygen container assy
cover 06C-180 from the angle 06C-190.
(d) Remove the screws 06C-240, the washers 06C-250 and the angle 06C-190
from the aft side wall assembly 06C-010.
(e) Remove the ground cable from the oxygen container assy 06C-230.
(f) Remove the screws 06C-240, 06C-245, the washers 06C-250 and the oxygen
container assy 06C-230 from the angles 06C-220.
(g) Remove the screws 06C-240, the washers 06C-250 and the angles 06C-220
from the aft side wall assembly 06C-010.
(h) Remove the screws 06C-310, the washers 06C-250 and the angle 06C-360
from the aft side wall assembly 06C-010.
(j) Remove the screws 06C-370 and the single door emergency unlocking device
assembly 06C-380 from the post assembly 06C-270.
(k) Disassemble the single door emergency unlocking device assembly 06C-380
as follows:
1 Remove the bolt 06C-440 and the emergency unlocking device strike
06C-400 from the emergency unlocking device housing 06C-390.
For Myanmar Airways (MMA) use only
2 Remove the pin 06C-420, the snap catch 06C-430 and the emergency
unlocking device pivot 06C-410 from the emergency unlocking device
housing 06C-390.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06C-430 and the pin 06C-420.
(l) Remove the caps 06C-320, the screws 06C-310, 06C-330, the washers
06C-250 and the post assembly 06C-270.
1 Remove the screws 06C-280 and the plates 06C-300 from the post
assembly 06C-270.
(n) Remove the screws 06C-350 and the toilet seat-cover dispenser 06C-340 from
the aft side wall assembly 06C-010.
(p) Remove the screw 06C-370 and the coat hook 06C-490 from the aft side wall
assembly 06C-010.
(q) Remove the screws 06C-040, 06C-050 and the fittings 06C-020, 06C-030.
SUBTASK 25-41-58-010-011-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3025
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06C-160 from the handle assemblies 06C-140.
2 Remove the handle assemblies 06C-140 from the aft side wall assembly
06C-010.
3 Remove the special screws 06C-150 and the special washers 06C-170
from the aft side wall assembly 06C-010.
(b) Remove the studs 06C-260 and the washers 06C-250 from the oxygen
container assy cover 06C-180.
(c) Remove the screws 06C-200, the nuts 06C-210 and the oxygen container assy
cover 06C-180 from the angle 06C-190.
(d) Remove the screws 06C-240, the washers 06C-250 and the angle 06C-190
from the aft side wall assembly 06C-010.
(e) Remove the screws 06C-460, the washers 06C-470, the clamps 06C-480 and
the hose 06C-450 from the aft side wall assembly 06C-010.
(f) Remove the hose 06C-450 from the oxygen container assy 06C-230.
(g) Remove the ground cable from the oxygen container assy 06C-230.
(h) Remove the screws 06C-240, the washers 06C-250 and the oxygen container
assy 06C-230 from the angles 06C-220.
(j) Remove the screws 06C-240, the washers 06C-250 and the angles 06C-220
from the aft side wall assembly 06C-010.
(k) Remove the screws 06C-310, the washers 06C-250 and the angle 06C-360
from the aft side wall assembly 06C-010.
(l) Remove the screws 06C-371 and the single door emergency unlocking device
assembly 06C-380 from the post assembly 06C-270.
For Myanmar Airways (MMA) use only
(m) Disassemble the single door emergency unlocking device assembly 06C-380
as follows:
1 Remove the bolt 06C-440 and the emergency unlocking device strike
06C-400 from the emergency unlocking device housing 06C-390.
2 Remove the pin 06C-420, the snap catch 06C-430 and the emergency
unlocking device pivot 06C-410 from the emergency unlocking device
housing 06C-390.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06C-430 and the pin 06C-420.
(n) Remove the caps 06C-320, the screws 06C-310, 06C-330, the washers
06C-250 and the post assembly 06C-270.
1 Remove the screws 06C-280 and the plates 06C-300 from the post
assembly 06C-270.
(q) Remove the screws 06C-350 and the toilet seat-cover dispenser 06C-340 from
the aft side wall assembly 06C-010.
(r) Remove the screws 06C-040, 06C-050 and the fittings 06C-020, 06C-030.
SUBTASK 25-41-58-010-011-E01
D2549010410400
(0) Removal of the Side Wall (06C-1)
NOTE: See TABLE for the references for the replacement procedures of
For Myanmar Airways (MMA) use only
Table 3026
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06C-160 from the handle assemblies 06C-140.
2 Remove the handle assemblies 06C-140 from the aft side wall assembly
06C-010.
3 Remove the special screws 06C-150 and the special washers 06C-170
from the aft side wall assembly 06C-010.
(b) Remove the studs 06C-260 and the washers 06C-250 from the oxygen
container assy cover 06C-180.
(c) Remove the screws 06C-200, the nuts 06C-210 and the oxygen container assy
cover 06C-180 from the angle 06C-190.
(d) Remove the screws 06C-240, the washers 06C-250 and the angle 06C-190
from the aft side wall assembly 06C-010.
(e) Remove the ground cable from the oxygen container assy 06C-230.
(f) Remove the screws 06C-240, the washers 06C-250 and the oxygen container
assy 06C-230 from the angles 06C-220.
(g) Remove the screws 06C-240, the washers 06C-250 and the angles 06C-220
from the aft side wall assembly 06C-010.
(h) Remove the screws 06C-310, the washers 06C-250 and the angle 06C-360
from the aft side wall assembly 06C-010.
For Myanmar Airways (MMA) use only
(j) Remove the screws 06C-371 and the single door emergency unlocking device
assembly 06C-380 from the post assembly 06C-270.
(k) Disassemble the single door emergency unlocking device assembly 06C-380
as follows:
1 Remove the bolt 06C-440 and the emergency unlocking device strike
06C-400 from the emergency unlocking device housing 06C-390.
2 Remove the pin 06C-420, the snap catch 06C-430 and the emergency
unlocking device pivot 06C-410 from the emergency unlocking device
housing 06C-390.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06C-430 and the pin 06C-420.
(l) Remove the caps 06C-320, the screws 06C-310, 06C-330, the washers
06C-250 and the post assembly 06C-270.
1 Remove the screws 06C-280 and the plates 06C-300 from the post
assembly 06C-270.
(n) Remove the screws 06C-350 and the toilet seat-cover dispenser 06C-340 from
the aft side wall assembly 06C-010.
(p) Remove the screws 06C-040, 06C-050 and the fittings 06C-020, 06C-030.
SUBTASK 25-41-58-010-011-F01
D2549020310000
For Myanmar Airways (MMA) use only
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3027
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06C-160 from the handle assemblies 06C-140.
2 Remove the handle assemblies 06C-140 from the aft side wall assembly
06C-010.
3 Remove the special screws 06C-150 and the special washers 06C-170
from the aft side wall assembly 06C-010.
(b) Remove the studs 06C-260 and the washers 06C-250 from the oxygen
container assy cover 06C-180.
(c) Remove the screws 06C-200, the nuts 06C-210 and the oxygen container assy
cover 06C-180 from the angle 06C-190.
(d) Remove the screws 06C-240, the washers 06C-250 and the angle 06C-190
from the aft side wall assembly 06C-010.
(e) Remove the ground cable from the oxygen container assy 06C-230.
(f) Remove the screws 06C-240, the washers 06C-250 and the oxygen container
assy 06C-230 from the angles 06C-220.
(g) Remove the screws 06C-240, the washers 06C-250 and the angles 06C-220
from the aft side wall assembly 06C-010.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06C-310, the washers 06C-250 and the angle 06C-360
from the aft side wall assembly 06C-010.
(j) Remove the screws 06C-371 and the single door emergency unlocking device
assembly 06C-380 from the post assembly 06C-270.
(k) Disassemble the single door emergency unlocking device assembly 06C-380
as follows:
1 Remove the bolt 06C-440 and the emergency unlocking device strike
06C-400 from the emergency unlocking device housing 06C-390.
2 Remove the pin 06C-420, the snap catch 06C-430 and the emergency
unlocking device pivot 06C-410 from the emergency unlocking device
housing 06C-390.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06C-430 and the pin 06C-420.
(l) Remove the caps 06C-320, the screws 06C-310, 06C-330, the washers
06C-250 and the post assembly 06C-270.
1 Remove the screws 06C-280 and the plates 06C-300 from the post
assembly 06C-270.
(n) Remove the screws 06C-040, 06C-050 and the fittings 06C-020, 06C-030.
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-010-011-G01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3028
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06C-160 from the handle assemblies 06C-140.
2 Remove the handle assemblies 06C-140 from the aft side wall assembly
06C-010.
3 Remove the special screws 06C-150 and the special washers 06C-170
from the aft side wall assembly 06C-010.
(b) Remove the studs 06C-260 and the washers 06C-250 from the oxygen
container assy cover 06C-180.
(c) Remove the screws 06C-200, the nuts 06C-210 and the oxygen container assy
cover 06C-180 from the angle 06C-190.
(d) Remove the screws 06C-240, the washers 06C-250 and the angle 06C-190
from the aft side wall assembly 06C-010.
(e) Remove the ground cable from the oxygen container assy 06C-230.
(f) Remove the screws 06C-240, 06C-245, the washers 06C-250 and the oxygen
container assy 06C-230 from the angles 06C-220.
For Myanmar Airways (MMA) use only
(g) Remove the screws 06C-240, the washers 06C-250 and the angles 06C-220
from the aft side wall assembly 06C-010.
(h) Remove the screws 06C-310, the washers 06C-250 and the angle 06C-360
from the aft side wall assembly 06C-010.
(j) Remove the screws 06C-371 and the single door emergency unlocking device
assembly 06C-380 from the post assembly 06C-270.
(k) Disassemble the single door emergency unlocking device assembly 06C-380
as follows:
1 Remove the bolt 06C-440 and the emergency unlocking device strike
06C-400 from the emergency unlocking device housing 06C-390.
2 Remove the pin 06C-420, the snap catch 06C-430 and the emergency
unlocking device pivot 06C-410 from the emergency unlocking device
housing 06C-390.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06C-430 and the pin 06C-420.
(l) Remove the caps 06C-320, the screws 06C-310, 06C-330, the washers
06C-250 and the post assembly 06C-270.
1 Remove the screws 06C-280 and the plates 06C-300 from the post
assembly 06C-270.
For Myanmar Airways (MMA) use only
(n) Remove the screws 06C-040, 06C-050 and the fittings 06C-020, 06C-030.
TASK 25-41-58-000-804-E01
A. General
For Myanmar Airways (MMA) use only
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-012-A01
D2549030708600 D2549030709800
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3029
For Myanmar Airways (MMA) use only
1 Remove the security pins 06D-160 from the handle assemblies 06D-140.
2 Remove the handle assemblies 06D-140 from the aft side wall assembly
06D-010.
3 Remove the special screws 06D-150 and the special washers 06D-170
from the aft side wall assembly 06D-010.
(b) Remove the studs 06D-260 and the washers 06D-250 from the oxygen
container assy cover 06D-180.
(c) Remove the screws 06D-200, the nuts 06D-210 and the oxygen container assy
cover 06D-180 from the angle 06D-190.
(d) Remove the screws 06D-240, the washers 06D-250 and the angle 06D-190
from the aft side wall assembly 06D-010.
(e) Remove the screws 06D-470, the washers 06D-480, the clamps 06D-490 and
the hose 06D-460 from the aft side wall assembly 06D-010.
(f) Remove the hose 06D-460 from the oxygen container assy 06D-230.
(g) Remove the ground cable from the oxygen container assy 06D-230.
(h) Remove the screws 06D-240, the washers 06D-250 and the oxygen container
assy 06D-230 from the angles 06D-220.
(j) Remove the screws 06D-240, the washers 06D-250 and the angles 06D-220
from the aft side wall assembly 06D-010.
(k) Remove the screws 06D-310, the washers 06D-250 and the angle 06D-340
from the aft side wall assembly 06D-010.
(l) Remove the screws 06D-351 and the single door emergency unlocking device
assembly 06D-360 from the post assembly 06D-270.
(m) Disassemble the single door emergency unlocking device assembly 06D-360
as follows:
1 Remove the bolt 06D-420 and the emergency unlocking device strike
06D-380 from the emergency unlocking device housing 06D-370.
2 Remove the pin 06D-400, the snap catch 06D-410 and the emergency
unlocking device pivot 06D-390 from the emergency unlocking device
housing 06D-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06D-410 and the pin 06D-400.
(n) Remove the caps 06D-320, the screws 06D-310, 06D-330, the washers
06D-250 and the post assembly 06D-270.
1 Remove the screws 06D-280 and the plates 06D-300 from the post
assembly 06D-270.
(q) Remove the screws 06D-440 and the toilet seat-cover dispenser 06D-430 from
the aft side wall assembly 06D-010.
(r) Remove the screw 06D-351 and the coat hook 06D-450 from the aft side wall
assembly 06D-010.
(s) Remove the screws 06D-040, 06D-050 and the fittings 06D-020, 06D-030.
SUBTASK 25-41-58-010-012-B01
D2549030706800
(0) Removal of the Side Wall (06D-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
For Myanmar Airways (MMA) use only
Table 3030
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06D-160 from the handle assemblies 06D-140.
2 Remove the handle assemblies 06D-140 from the aft side wall assembly
06D-010.
3 Remove the special screws 06D-150 and the special washers 06D-170
from the aft side wall assembly 06D-010.
(b) Remove the studs 06D-260 and the washers 06D-250 from the oxygen
container assy cover 06D-180.
(c) Remove the screws 06D-200, the nuts 06D-210 and the oxygen container assy
cover 06D-180 from the angle 06D-190.
(d) Remove the screws 06D-240, the washers 06D-250 and the angle 06D-190
from the aft side wall assembly 06D-010.
(e) Remove the ground cable from the oxygen container assy 06D-230.
(f) Remove the screws 06D-240, the washers 06D-250 and the oxygen container
assy 06D-230 from the angles 06D-220.
(g) Remove the screws 06D-240, the washers 06D-250 and the angles 06D-220
from the aft side wall assembly 06D-010.
(h) Remove the screws 06D-310, the washers 06D-250 and the angle 06D-340
from the aft side wall assembly 06D-010.
(j) Remove the screws 06D-351 and the single door emergency unlocking device
assembly 06D-360 from the post assembly 06D-270.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06D-360
as follows:
1 Remove the bolt 06D-420 and the emergency unlocking device strike
06D-380 from the emergency unlocking device housing 06D-370.
2 Remove the pin 06D-400, the snap catch 06D-410 and the emergency
unlocking device pivot 06D-390 from the emergency unlocking device
housing 06D-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06D-410 and the pin 06D-400.
(l) Remove the caps 06D-320, the screws 06D-310, 06D-330, the washers
06D-250 and the post assembly 06D-270.
1 Remove the screws 06D-280 and the plates 06D-300 from the post
assembly 06D-270.
(n) Remove the screws 06D-440 and the toilet seat-cover dispenser 06D-430 from
the aft side wall assembly 06D-010.
(p) Remove the screw 06D-351 and the coat hook 06D-450 from the aft side wall
assembly 06D-010.
(q) Remove the screws 06D-040, 06D-050 and the fittings 06D-020, 06D-030.
SUBTASK 25-41-58-010-012-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3031
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06D-160 from the handle assemblies 06D-140.
2 Remove the handle assemblies 06D-140 from the aft side wall assembly
06D-010.
3 Remove the special screws 06D-150 and the special washers 06D-170
from the aft side wall assembly 06D-010.
(b) Remove the studs 06D-260 and the washers 06D-250 from the oxygen
container assy cover 06D-180.
(c) Remove the screws 06D-200, the nuts 06D-210 and the oxygen container assy
cover 06D-180 from the angle 06D-190.
(d) Remove the screws 06D-240, the washers 06D-250 and the angle 06D-190
from the aft side wall assembly 06D-010.
(e) Remove the ground cable from the oxygen container assy 06D-230.
(f) Remove the screws 06D-240, 06D-243, the washers 06D-250, 06D-255 and
the oxygen container assy 06D-230 from the angles 06D-220.
(g) Remove the screws 06D-240, the washers 06D-250 and the angles 06D-220
from the aft side wall assembly 06D-010.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06D-310, the washers 06D-250 and the angle 06D-340
from the aft side wall assembly 06D-010.
(j) Remove the screws 06D-350 and the single door emergency unlocking device
assembly 06D-360 from the post assembly 06D-270.
(k) Disassemble the single door emergency unlocking device assembly 06D-360
as follows:
1 Remove the bolt 06D-420 and the emergency unlocking device strike
06D-380 from the emergency unlocking device housing 06D-370.
2 Remove the pin 06D-400, the snap catch 06D-410 and the emergency
unlocking device pivot 06D-390 from the emergency unlocking device
housing 06D-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06D-410 and the pin 06D-400.
(l) Remove the caps 06D-320, the screws 06D-310, 06D-330, the washers
06D-250 and the post assembly 06D-270.
1 Remove the screws 06D-280 and the plates 06D-300 from the post
assembly 06D-270.
(n) Remove the screws 06D-440 and the toilet seat-cover dispenser 06D-430 from
the aft side wall assembly 06D-010.
For Myanmar Airways (MMA) use only
(p) Remove the screws 06D-040, 06D-050 and the fittings 06D-020, 06D-030.
SUBTASK 25-41-58-010-012-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3032
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06D-160 from the handle assemblies 06D-140.
2 Remove the handle assemblies 06D-140 from the aft side wall assembly
06D-010.
3 Remove the special screws 06D-150 and the special washers 06D-170
from the aft side wall assembly 06D-010.
(b) Remove the studs 06D-260 and the washers 06D-250 from the oxygen
container assy cover 06D-180.
(c) Remove the screws 06D-200, the nuts 06D-210 and the oxygen container assy
cover 06D-180 from the angle 06D-190.
(d) Remove the screws 06D-240, the washers 06D-250 and the angle 06D-190
from the aft side wall assembly 06D-010.
For Myanmar Airways (MMA) use only
(e) Remove the ground cable from the oxygen container assy 06D-230.
(f) Remove the screws 06D-240, the washers 06D-250 and the oxygen container
assy 06D-230 from the angles 06D-220.
(g) Remove the screws 06D-240, the washers 06D-250 and the angles 06D-220
from the aft side wall assembly 06D-010.
(h) Remove the screws 06D-310, the washers 06D-250 and the angle 06D-340
from the aft side wall assembly 06D-010.
(j) Remove the screws 06D-350 and the single door emergency unlocking device
assembly 06D-360 from the post assembly 06D-270.
(k) Disassemble the single door emergency unlocking device assembly 06D-360
as follows:
1 Remove the bolt 06D-420 and the emergency unlocking device strike
06D-380 from the emergency unlocking device housing 06D-370.
2 Remove the pin 06D-400, the snap catch 06D-410 and the emergency
unlocking device pivot 06D-390 from the emergency unlocking device
housing 06D-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06D-410 and the pin 06D-400.
(l) Remove the caps 06D-320, the screws 06D-310, 06D-330, the washers
06D-250 and the post assembly 06D-270.
1 Remove the screws 06D-280 and the plates 06D-300 from the post
assembly 06D-270.
(n) Remove the screws 06D-440 and the toilet seat-cover dispenser 06D-430 from
the aft side wall assembly 06D-010.
(p) Remove the screws 06D-040, 06D-050 and the fittings 06D-020, 06D-030.
SUBTASK 25-41-58-010-012-E01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3033
For Myanmar Airways (MMA) use only
1 Remove the security pins 06D-160 from the handle assemblies 06D-140.
2 Remove the handle assemblies 06D-140 from the aft side wall assembly
06D-010.
3 Remove the special screws 06D-150 and the special washers 06D-170
from the aft side wall assembly 06D-010.
(b) Remove the studs 06D-260 and the washers 06D-250 from the oxygen
container assy cover 06D-180.
(c) Remove the screws 06D-200, the nuts 06D-210 and the oxygen container assy
cover 06D-180 from the angle 06D-190.
(d) Remove the screws 06D-240, the washers 06D-250 and the angle 06D-190
from the aft side wall assembly 06D-010.
(e) Remove the ground cable from the oxygen container assy 06D-230.
(f) Remove the screws 06D-240, the washers 06D-250 and the oxygen container
assy 06D-230 from the angles 06D-220.
(g) Remove the screws 06D-240, the washers 06D-250 and the angles 06D-220
from the aft side wall assembly 06D-010.
(h) Remove the screws 06D-310, the washers 06D-250 and the angle 06D-340
from the aft side wall assembly 06D-010.
(j) Remove the screws 06D-350 and the single door emergency unlocking device
assembly 06D-360 from the post assembly 06D-270.
(k) Disassemble the single door emergency unlocking device assembly 06D-360
as follows:
1 Remove the bolt 06D-420 and the emergency unlocking device strike
06D-380 from the emergency unlocking device housing 06D-370.
For Myanmar Airways (MMA) use only
2 Remove the pin 06D-400, the snap catch 06D-410 and the emergency
unlocking device pivot 06D-390 from the emergency unlocking device
housing 06D-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06D-410 and the pin 06D-400.
(l) Remove the caps 06D-320, the screws 06D-310, 06D-330, the washers
06D-250 and the post assembly 06D-270.
1 Remove the screws 06D-280 and the plates 06D-300 from the post
assembly 06D-270.
(n) Remove the screws 06D-040, 06D-050 and the fittings 06D-020, 06D-030.
SUBTASK 25-41-58-010-012-F01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3034
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06D-160 from the handle assemblies 06D-140.
2 Remove the handle assemblies 06D-140 from the aft side wall assembly
06D-010.
3 Remove the special screws 06D-150 and the special washers 06D-170
from the aft side wall assembly 06D-010.
(b) Remove the studs 06D-260 and the washers 06D-250 from the oxygen
container assy cover 06D-180.
(c) Remove the screws 06D-200, 06D-245 the nuts 06D-210 and the oxygen
container assy cover 06D-180 from the angle 06D-190.
(d) Remove the screws 06D-240, the washers 06D-250 and the angle 06D-190
from the aft side wall assembly 06D-010.
(e) Remove the ground cable from the oxygen container assy 06D-230.
(f) Remove the screws 06D-240, 06D-243, the washers 06D-250 and the oxygen
container assy 06D-230 from the angles 06D-220.
(g) Remove the screws 06D-240, the washers 06D-250 and the angles 06D-220
from the aft side wall assembly 06D-010.
(h) Remove the screws 06D-310, the washers 06D-250 and the angle 06D-340
from the aft side wall assembly 06D-010.
(j) Remove the screws 06D-350 and the single door emergency unlocking device
assembly 06D-360 from the post assembly 06D-270.
(k) Disassemble the single door emergency unlocking device assembly 06D-360
as follows:
1 Remove the bolt 06D-420 and the emergency unlocking device strike
06D-380 from the emergency unlocking device housing 06D-370.
2 Remove the pin 06D-400, the snap catch 06D-410 and the emergency
unlocking device pivot 06D-390 from the emergency unlocking device
housing 06D-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06D-410 and the pin 06D-400.
(l) Remove the caps 06D-320, the screws 06D-310, 06D-330, the washers
06D-250 and the post assembly 06D-270.
1 Remove the screws 06D-280 and the plates 06D-300 from the post
assembly 06D-270.
(n) Remove the screws 06D-040, 06D-050 and the fittings 06D-020, 06D-030.
TASK 25-41-58-000-804-F01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-013-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3035
For Myanmar Airways (MMA) use only
1 Remove the setscrews 06E-490 and the handle 06E-460 from the screws
06E-470.
2 Remove the screws 06E-470 and the washers 06E-480 from the aft side
wall assembly 06E-010.
(b) Remove the studs 06E-260 and the washers 06E-250 from the oxygen
container assy cover 06E-180.
(c) Remove the screws 06E-200, the nuts 06E-210 and the oxygen container assy
cover 06E-180 from the angle 06E-190.
(d) Remove the screws 06E-240, the washers 06E-250 and the angle 06E-190
from the aft side wall assembly 06E-010.
(e) Remove the ground cable from the oxygen container assy 06E-230.
(f) Remove the screws 06E-240, the washers 06E-250 and the oxygen container
assy 06E-230 from the angles 06E-220.
(g) Remove the screws 06E-240, the washers 06E-250 and the angles 06E-220
from the aft side wall assembly 06E-010.
(h) Remove the screws 06E-310, the washers 06E-250 and the angle 06E-340
from the aft side wall assembly 06E-010.
(j) Remove the screws 06E-350 and the single door emergency unlocking device
assembly 06E-360 from the post assembly 06E-270.
(k) Disassemble the single door emergency unlocking device assembly 06E-360
as follows:
1 Remove the bolt 06E-420 and the emergency unlocking device strike
06E-380 from the emergency unlocking device housing 06E-370.
For Myanmar Airways (MMA) use only
2 Remove the pin 06E-400, the snap catch 06E-410 and the emergency
unlocking device pivot 06E-390 from the emergency unlocking device
housing 06E-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06E-410 and the pin 06E-400.
(l) Remove the caps 06E-320, the screws 06E-310, 06E-330, the washers
06E-250 and the post assembly 06E-270.
1 Remove the screws 06E-280 and the plates 06E-300 from the post
assembly 06E-270.
(n) Remove the screws 06E-440 and the toilet seat-cover dispenser 06E-430 from
the aft side wall assembly 06E-010.
(p) Remove the screws 06E-040, 06E-050 and the fittings 06E-020, 06E-030.
SUBTASK 25-41-58-010-013-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3036
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06E-160 from the handle assemblies 06E-140.
2 Remove the handle assemblies 06E-140 from the aft side wall assembly
06E-010.
3 Remove the special screws 06E-150 and the special washers 06E-170
from the aft side wall assembly 06E-010.
(b) Remove the studs 06E-260 and the washers 06E-250 from the oxygen
container assy cover 06E-180.
(c) Remove the screws 06E-200, the nuts 06E-210 and the oxygen container assy
cover 06E-180 from the angle 06E-190.
(d) Remove the screws 06E-240, the washers 06E-250 and the angle 06E-190
from the aft side wall assembly 06E-010.
(e) Remove the ground cable from the oxygen container assy 06E-230.
(f) Remove the screws 06E-240, the washers 06E-250 and the oxygen container
assy 06E-230 from the angles 06E-220.
(g) Remove the screws 06E-240, the washers 06E-250 and the angles 06E-220
from the aft side wall assembly 06E-010.
(h) Remove the screws 06E-310, the washers 06E-250 and the angle 06E-340
from the aft side wall assembly 06E-010.
(j) Remove the screws 06E-350 and the single door emergency unlocking device
assembly 06E-360 from the post assembly 06E-270.
(k) Disassemble the single door emergency unlocking device assembly 06E-360
as follows:
1 Remove the bolt 06E-420 and the emergency unlocking device strike
06E-380 from the emergency unlocking device housing 06E-370.
2 Remove the pin 06E-400, the snap catch 06E-410 and the emergency
unlocking device pivot 06E-390 from the emergency unlocking device
housing 06E-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06E-410 and the pin 06E-400.
(l) Remove the caps 06E-320, the screws 06E-310, 06E-330, the washers
06E-250 and the post assembly 06E-270.
1 Remove the screws 06E-280 and the plates 06E-300 from the post
assembly 06E-270.
(n) Remove the screws 06E-440 and the toilet seat-cover dispenser 06E-430 from
the aft side wall assembly 06E-010.
(p) Remove the screw 06E-351 and the coat hook 06E-500 from the aft side wall
assembly 06E-010.
(q) Remove the screws 06E-040, 06E-050 and the fittings 06E-020, 06E-030.
SUBTASK 25-41-58-010-013-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3037
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06E-160 from the handle assemblies 06E-140.
2 Remove the handle assemblies 06E-140 from the aft side wall assembly
06E-010.
3 Remove the special screws 06E-150 and the special washers 06E-170
from the aft side wall assembly 06E-010.
(b) Remove the studs 06E-260 and the washers 06E-250 from the oxygen
container assy cover 06E-180.
(c) Remove the screws 06E-200, 06E-243, the nuts 06E-210 and the oxygen
container assy cover 06E-180 from the angle 06E-190.
(d) Remove the screws 06E-240, the washers 06E-250 and the angle 06E-190
from the aft side wall assembly 06E-010.
(e) Remove the ground cable from the oxygen container assy 06E-230.
(f) Remove the screws 06E-240, 06E-241, the washers 06E-250 and the oxygen
container assy 06E-230 from the angles 06E-220.
(g) Remove the screws 06E-240, the washers 06E-250 and the angles 06E-220
from the aft side wall assembly 06E-010.
(h) Remove the screws 06E-310, the washers 06E-250 and the angle 06E-340
from the aft side wall assembly 06E-010.
(j) Remove the screws 06E-350 and the single door emergency unlocking device
assembly 06E-360 from the post assembly 06E-270.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06E-360
as follows:
1 Remove the bolt 06E-420 and the emergency unlocking device strike
06E-380 from the emergency unlocking device housing 06E-370.
2 Remove the pin 06E-400, the snap catch 06E-410 and the emergency
unlocking device pivot 06E-390 from the emergency unlocking device
housing 06E-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06E-410 and the pin 06E-400.
(l) Remove the caps 06E-320, the screws 06E-310, 06E-330, the washers
06E-250 and the post assembly 06E-270.
1 Remove the screws 06E-280 and the plates 06E-300 from the post
assembly 06E-270.
(n) Remove the screws 06E-440 and the toilet seat-cover dispenser 06E-430 from
the aft side wall assembly 06E-010.
(p) Remove the screws 06E-040, 06E-050 and the fittings 06E-020, 06E-030.
SUBTASK 25-41-58-010-013-D01
D2549020306000 R225401807-000
(0) Removal of the Side Wall (06E-1)
NOTE: See TABLE for the references for the replacement procedures of
For Myanmar Airways (MMA) use only
Table 3038
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06E-160 from the handle assemblies 06E-140.
2 Remove the handle assemblies 06E-140 from the aft side wall assembly
06E-010.
3 Remove the special screws 06E-150 and the special washers 06E-170
from the aft side wall assembly 06E-010.
(b) Remove the studs 06E-260 and the washers 06E-250 from the oxygen
container assy cover 06E-180.
(c) Remove the screws 06E-200, the nuts 06E-210 and the oxygen container assy
cover 06E-180 from the angle 06E-190.
(d) Remove the screws 06E-240, the washers 06E-250 and the angle 06E-190
from the aft side wall assembly 06E-010.
(e) Remove the ground cable from the oxygen container assy 06E-230.
(f) Remove the screws 06E-240, 06E-241, the washers 06E-250 and the oxygen
container assy 06E-230 from the angles 06E-220.
(g) Remove the screws 06E-240, the washers 06E-250 and the angles 06E-220
from the aft side wall assembly 06E-010.
(h) Remove the screws 06E-310, the washers 06E-250 and the angle 06E-340
from the aft side wall assembly 06E-010.
For Myanmar Airways (MMA) use only
(j) Remove the screws 06E-350 and the single door emergency unlocking device
assembly 06E-360 from the post assembly 06E-270.
(k) Disassemble the single door emergency unlocking device assembly 06E-360
as follows:
1 Remove the bolt 06E-420 and the emergency unlocking device strike
06E-380 from the emergency unlocking device housing 06E-370.
2 Remove the pin 06E-400, the snap catch 06E-410 and the emergency
unlocking device pivot 06E-390 from the emergency unlocking device
housing 06E-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06E-410 and the pin 06E-400.
(l) Remove the caps 06E-320, the screws 06E-310, 06E-330, the washers
06E-250 and the post assembly 06E-270.
1 Remove the screws 06E-280 and the plates 06E-300 from the post
assembly 06E-270.
(n) Remove the screws 06E-440 and the toilet seat-cover dispenser 06E-430 from
the aft side wall assembly 06E-010.
(p) Remove the screws 06E-040, 06E-050 and the fittings 06E-020, 06E-030.
SUBTASK 25-41-58-010-013-E01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3039
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06E-160 from the handle assemblies 06E-140.
2 Remove the handle assemblies 06E-140 from the aft side wall assembly
06E-010.
3 Remove the special screws 06E-150 and the special washers 06E-170
from the aft side wall assembly 06E-010.
(b) Remove the studs 06E-260 and the washers 06E-250 from the oxygen
container assy cover 06E-180.
(c) Remove the screws 06E-200, the nuts 06E-210 and the oxygen container assy
cover 06E-180 from the angle 06E-190.
(d) Remove the screws 06E-240, the washers 06E-250 and the angle 06E-190
from the aft side wall assembly 06E-010.
(e) Remove the ground cable from the oxygen container assy 06E-230.
(f) Remove the screws 06E-240, 06E-241, the washers 06E-250 and the oxygen
container assy 06E-230 from the angles 06E-220.
(g) Remove the screws 06E-240, the washers 06E-250 and the angles 06E-220
from the aft side wall assembly 06E-010.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06E-310, the washers 06E-250 and the angle 06E-340
from the aft side wall assembly 06E-010.
(j) Remove the screws 06E-350 and the single door emergency unlocking device
assembly 06E-360 from the post assembly 06E-270.
(k) Disassemble the single door emergency unlocking device assembly 06E-360
as follows:
1 Remove the bolt 06E-420 and the emergency unlocking device strike
06E-380 from the emergency unlocking device housing 06E-370.
2 Remove the pin 06E-400, the snap catch 06E-410 and the emergency
unlocking device pivot 06E-390 from the emergency unlocking device
housing 06E-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06E-410 and the pin 06E-400.
(l) Remove the caps 06E-320, the screws 06E-310, 06E-330, the washers
06E-250 and the post assembly 06E-270.
1 Remove the screws 06E-280 and the plates 06E-300 from the post
assembly 06E-270.
(n) Remove the screws 06E-040, 06E-050 and the fittings 06E-020, 06E-030.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-804-G01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-014-A01
For Myanmar Airways (MMA) use only
D2549020902600
(1) Removal of the Side Wall (06F-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3040
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06F-320 from the handle assembly 06F-300.
2 Remove the handle assembly 06F-300 from the aft side wall assembly
06F-010.
3 Remove the special screws 06F-310 and the special washers 06F-330
from the aft side wall assembly 06F-010.
(b) Remove the screws 06F-270, the washers 06F-210 and the support 06F-340
from the aft side wall assembly 06F-010.
(c) Remove the studs 06F-220 and the washers 06F-210 from the oxygen
container assy cover 06F-140.
(d) Remove the screws 06F-160, the nuts 06F-170 and the oxygen container assy
cover 06F-140 from the angle 06F-150.
(e) Remove the screws 06F-200, the washers 06F-210 and the angle 06F-150
from the aft side wall assembly 06F-010.
(f) Remove the ground cable from the oxygen container assy 06F-190.
(g) Remove the screws 06F-200, the washers 06F-210 and the oxygen container
assy 06F-190 from the angles 06F-180.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06F-200, the washers 06F-210 and the angles 06F-180
from the aft side wall assembly 06F-010.
(j) Remove the screws 06F-270, the washers 06F-210 and the angle 06F-350
from the aft side wall assembly 06F-010.
(k) Remove the screws 06F-430 and the single door emergency unlocking device
assembly 06F-360 from the post assembly 06F-230.
(l) Disassemble the single door emergency unlocking device assembly 06F-360
as follows:
1 Remove the bolt 06F-420 and the emergency unlocking device strike
06F-380 from the emergency unlocking device housing 06F-370.
2 Remove the pin 06F-400, the snap catch 06F-410 and the emergency
unlocking device pivot 06F-390 from the emergency unlocking device
housing 06F-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06F-410 and the pin 06F-400.
(m) Remove the caps 06F-280, the screws 06F-270, 06F-290, the washers
06F-210 and the post assembly 06F-230.
1 Remove the screws 06F-240 and the plates 06F-260 from the post
assembly 06F-230.
For Myanmar Airways (MMA) use only
(o) Remove the screws 06F-450 and the toilet seat-cover dispenser 06F-440 from
the aft side wall assembly 06F-010.
(p) Remove the screw 06F-431 and the coat hook 06F-460 from the aft side wall
assembly 06F-010.
(q) Remove the screws 06F-040, 06F-050 and the fittings 06F-020, 06F-030.
SUBTASK 25-41-58-010-014-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3041
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06F-320 from the handle assembly 06F-300.
2 Remove the handle assembly 06F-300 from the aft side wall assembly
06F-010.
3 Remove the special screws 06F-310 and the special washers 06F-330
from the aft side wall assembly 06F-010.
(b) Remove the screws 06F-270, the washers 06F-210 and the support 06F-340
from the aft side wall assembly 06F-010.
(c) Remove the studs 06F-220 and the washers 06F-210 from the oxygen
container assy cover 06F-140.
For Myanmar Airways (MMA) use only
(d) Remove the screws 06F-160, the nuts 06F-170 and the oxygen container assy
cover 06F-140 from the angle 06F-150.
(e) Remove the screws 06F-200, the washers 06F-210 and the angle 06F-150
from the aft side wall assembly 06F-010.
(f) Remove the ground cable from the oxygen container assy 06F-190.
(g) Remove the screws 06F-200, 06F-205, the washers 06F-210 and the oxygen
container assy 06F-190 from the angles 06F-180.
(h) Remove the screws 06F-200, the washers 06F-210 and the angles 06F-180
from the aft side wall assembly 06F-010.
(j) Remove the screws 06F-270, the washers 06F-210 and the angle 06F-350
from the aft side wall assembly 06F-010.
(k) Remove the screws 06F-430 and the single door emergency unlocking device
assembly 06F-360 from the post assembly 06F-230.
(l) Disassemble the single door emergency unlocking device assembly 06F-360
as follows:
1 Remove the bolt 06F-420 and the emergency unlocking device strike
06F-380 from the emergency unlocking device housing 06F-370.
2 Remove the pin 06F-400, the snap catch 06F-410 and the emergency
unlocking device pivot 06F-390 from the emergency unlocking device
housing 06F-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
For Myanmar Airways (MMA) use only
(m) Remove the caps 06F-280, the screws 06F-270, 06F-290, the washers
06F-210 and the post assembly 06F-230.
1 Remove the screws 06F-240 and the plates 06F-260 from the post
assembly 06F-230.
(o) Remove the screws 06F-450 and the toilet seat-cover dispenser 06F-440 from
the aft side wall assembly 06F-010.
(p) Remove the screws 06F-040, 06F-050 and the fittings 06F-020, 06F-030.
SUBTASK 25-41-58-010-014-C01
D2549010409200 D2549010410200
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3042
For Myanmar Airways (MMA) use only
1 Remove the security pins 06F-320 from the handle assembly 06F-300.
2 Remove the handle assembly 06F-300 from the aft side wall assembly
06F-010.
3 Remove the special screws 06F-310 and the special washers 06F-330
from the aft side wall assembly 06F-010.
(b) Remove the screws 06F-270, the washers 06F-210 and the support 06F-340
from the aft side wall assembly 06F-010.
(c) Remove the studs 06F-220 and the washers 06F-210 from the oxygen
container assy cover 06F-140.
(d) Remove the screws 06F-160, the nuts 06F-170 and the oxygen container assy
cover 06F-140 from the angle 06F-150.
(e) Remove the screws 06F-200, the washers 06F-210 and the angle 06F-150
from the aft side wall assembly 06F-010.
(f) Remove the ground cable from the oxygen container assy 06F-190.
(g) Remove the screws 06F-200, the washers 06F-210 and the oxygen container
assy 06F-190 from the angles 06F-180.
(h) Remove the screws 06F-200, the washers 06F-210 and the angles 06F-180
from the aft side wall assembly 06F-010.
(j) Remove the screws 06F-270, the washers 06F-210 and the angle 06F-350
from the aft side wall assembly 06F-010.
(k) Remove the screws 06F-430 and the single door emergency unlocking device
assembly 06F-360 from the post assembly 06F-230.
(l) Disassemble the single door emergency unlocking device assembly 06F-360
as follows:
1 Remove the bolt 06F-420 and the emergency unlocking device strike
06F-380 from the emergency unlocking device housing 06F-370.
2 Remove the pin 06F-400, the snap catch 06F-410 and the emergency
unlocking device pivot 06F-390 from the emergency unlocking device
housing 06F-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06F-410 and the pin 06F-400.
(m) Remove the caps 06F-280, the screws 06F-270, 06F-290, the washers
06F-210 and the post assembly 06F-230.
1 Remove the screws 06F-240 and the plates 06F-260 from the post
assembly 06F-230.
(o) Remove the screws 06F-450 and the toilet seat-cover dispenser 06F-440 from
the aft side wall assembly 06F-010.
(p) Remove the screws 06F-040, 06F-050 and the fittings 06F-020, 06F-030.
SUBTASK 25-41-58-010-014-D01
D2549040503400
(0) Removal of the Side Wall (06F-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3043
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06F-320 from the handle assembly 06F-300.
2 Remove the handle assembly 06F-300 from the aft side wall assembly
06F-010.
3 Remove the special screws 06F-310 and the special washers 06F-330
from the aft side wall assembly 06F-010.
(b) Remove the studs 06F-220 and the washers 06F-210 from the oxygen
container assy cover 06F-140.
(c) Remove the screws 06F-160, the nuts 06F-170 and the oxygen container assy
cover 06F-140 from the angle 06F-150.
(d) Remove the screws 06F-200, the washers 06F-210 and the angle 06F-150
from the aft side wall assembly 06F-010.
(e) Remove the ground cable from the oxygen container assy 06F-190.
(f) Remove the screws 06F-200, the washers 06F-210 and the oxygen container
assy 06F-190 from the angles 06F-180.
(g) Remove the screws 06F-200, the washers 06F-210 and the angles 06F-180
from the aft side wall assembly 06F-010.
(h) Remove the screws 06F-270, the washers 06F-210 and the angle 06F-350
from the aft side wall assembly 06F-010.
(j) Remove the screws 06F-430 and the single door emergency unlocking device
assembly 06F-360 from the post assembly 06F-230.
(k) Disassemble the single door emergency unlocking device assembly 06F-360
as follows:
1 Remove the bolt 06F-420 and the emergency unlocking device strike
06F-380 from the emergency unlocking device housing 06F-370.
2 Remove the pin 06F-400, the snap catch 06F-410 and the emergency
unlocking device pivot 06F-390 from the emergency unlocking device
housing 06F-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06F-410 and the pin 06F-400.
(l) Remove the caps 06F-280, the screws 06F-270, 06F-290, the washers
06F-210 and the post assembly 06F-230.
1 Remove the screws 06F-240 and the plates 06F-260 from the post
assembly 06F-230.
(n) Remove the screws 06F-450 and the toilet seat-cover dispenser 06F-440 from
the aft side wall assembly 06F-010.
(p) Remove the screws 06F-040, 06F-050 and the fittings 06F-020, 06F-030.
SUBTASK 25-41-58-010-014-E01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3044
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06F-320 from the handle assembly 06F-300.
2 Remove the handle assembly 06F-300 from the aft side wall assembly
06F-010.
3 Remove the special screws 06F-310 and the special washers 06F-330
from the aft side wall assembly 06F-010.
(b) Remove the screws 06F-270, the washers 06F-210 and the support 06F-340
from the aft side wall assembly 06F-010.
(c) Remove the studs 06F-220 and the washers 06F-210 from the oxygen
container assy cover 06F-140.
(d) Remove the screws 06F-160, the nuts 06F-170 and the oxygen container assy
cover 06F-140 from the angle 06F-150.
(e) Remove the screws 06F-200, the washers 06F-210 and the angle 06F-150
from the aft side wall assembly 06F-010.
(f) Remove the ground cable from the oxygen container assy 06F-190.
(g) Remove the screws 06F-200, 06F-205, the washers 06F-210 and the oxygen
container assy 06F-190 from the angles 06F-180.
(h) Remove the screws 06F-200, the washers 06F-210 and the angles 06F-180
from the aft side wall assembly 06F-010.
(j) Remove the screws 06F-270, the washers 06F-210 and the angle 06F-350
from the aft side wall assembly 06F-010.
For Myanmar Airways (MMA) use only
(k) Remove the screws 06F-430 and the single door emergency unlocking device
assembly 06F-360 from the post assembly 06F-230.
(l) Disassemble the single door emergency unlocking device assembly 06F-360
as follows:
1 Remove the bolt 06F-420 and the emergency unlocking device strike
06F-380 from the emergency unlocking device housing 06F-370.
2 Remove the pin 06F-400, the snap catch 06F-410 and the emergency
unlocking device pivot 06F-390 from the emergency unlocking device
housing 06F-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06F-410 and the pin 06F-400.
(m) Remove the caps 06F-280, the screws 06F-270, 06F-290, the washers
06F-210 and the post assembly 06F-230.
1 Remove the screws 06F-240 and the plates 06F-260 from the post
assembly 06F-230.
(o) Remove the screws 06F-040, 06F-050 and the fittings 06F-020, 06F-030.
SUBTASK 25-41-58-010-014-F01
D2547160900800
(0) Removal of the Side Wall (06F-1)
NOTE: See TABLE for the references for the replacement procedures of
For Myanmar Airways (MMA) use only
Table 3045
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06F-320 from the handle assembly 06F-300.
2 Remove the handle assembly 06F-300 from the aft side wall assembly
06F-010.
3 Remove the special screws 06F-310 and the special washers 06F-330
from the aft side wall assembly 06F-010.
(b) Remove the screws 06F-270, the washers 06F-210 and the support 06F-340
from the aft side wall assembly 06F-010.
(c) Remove the studs 06F-220 and the washers 06F-210 from the oxygen
container assy cover 06F-140.
(d) Remove the screws 06F-160, the nuts 06F-170 and the oxygen container assy
cover 06F-140 from the angle 06F-150.
(e) Remove the screws 06F-200, the washers 06F-210 and the angle 06F-150
from the aft side wall assembly 06F-010.
(f) Remove the ground cable from the oxygen container assy 06F-190.
(g) Remove the screws 06F-200, the washers 06F-210 and the oxygen container
assy 06F-190 from the angles 06F-180.
(h) Remove the screws 06F-200, the washers 06F-210 and the angles 06F-180
from the aft side wall assembly 06F-010.
For Myanmar Airways (MMA) use only
(j) Remove the screws 06F-270, the washers 06F-210 and the angle 06F-350
from the aft side wall assembly 06F-010.
(k) Remove the screws 06F-430 and the single door emergency unlocking device
assembly 06F-360 from the post assembly 06F-230.
(l) Disassemble the single door emergency unlocking device assembly 06F-360
as follows:
1 Remove the bolt 06F-420 and the emergency unlocking device strike
06F-380 from the emergency unlocking device housing 06F-370.
2 Remove the pin 06F-400, the snap catch 06F-410 and the emergency
unlocking device pivot 06F-390 from the emergency unlocking device
housing 06F-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06F-410 and the pin 06F-400.
(m) Remove the caps 06F-280, the screws 06F-270, 06F-290, the washers
06F-210 and the post assembly 06F-230.
1 Remove the screws 06F-240 and the plates 06F-260 from the post
assembly 06F-230.
(o) Remove the screws 06F-040, 06F-050 and the fittings 06F-020, 06F-030.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-804-H01
D2549010408200
15. Removal of the Side Wall
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-015-A01
For Myanmar Airways (MMA) use only
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3046
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06G-160 from the handle assemblies 06G-140.
2 Remove the handle assemblies 06G-140 from the aft side wall assembly
06G-010.
3 Remove the special screws 06G-150 and the special washers 06G-170
from the aft side wall assembly 06G-010.
(b) Remove the studs 06G-260 and the washers 06G-250 from the oxygen
container assy cover 06G-180.
(c) Remove the screws 06G-200, the nuts 06G-210 and the oxygen container assy
cover 06G-180 from the angle 06G-190.
(d) Remove the screws 06G-240, the washers 06G-250 and the angle 06G-190
from the aft side wall assembly 06G-010.
(e) Remove the ground cable from the oxygen container assy 06G-230.
(f) Remove the screws 06G-240, the washers 06G-250 and the oxygen container
assy 06G-230 from the angles 06G-220.
(g) Remove the screws 06G-240, the washers 06G-250 and the angles 06G-220
from the aft side wall assembly 06G-010.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06G-310, the washers 06G-250 and the angle 06G-360
from the aft side wall assembly 06G-010.
(j) Remove the screws 06G-370 and the single door emergency unlocking device
assembly 06G-380 from the post assembly 06G-270.
(k) Disassemble the single door emergency unlocking device assembly 06G-380
as follows:
1 Remove the bolt 06G-440 and the emergency unlocking device strike
06G-400 from the emergency unlocking device housing 06G-390.
2 Remove the pin 06G-420, the snap catch 06G-430 and the emergency
unlocking device pivot 06G-410 from the emergency unlocking device
housing 06G-390.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06G-430 and the pin 06G-420.
(l) Remove the caps 06G-320, the screws 06G-310, 06G-330, the washers
06G-250 and the post assembly 06G-270.
1 Remove the screws 06G-280 and the plates 06G-300 from the post
assembly 06G-270.
(n) Remove the screws 06G-350 and the toilet seat-cover dispenser 06G-340 from
the aft side wall assembly 06G-010.
For Myanmar Airways (MMA) use only
(p) Remove the screws 06G-350 and the lavatory picture frame kit 06G-450 from
the aft side wall assembly 06G-010.
(q) Remove the screws 06G-040, 06G-050 and the fittings 06G-020, 06G-030.
TASK 25-41-58-000-804-J01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-016-A01
D2549030712200 D2549030808000
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3047
For Myanmar Airways (MMA) use only
1 Remove the setscrews 06H-470 and the handle 06H-440 from the screws
06H-450.
2 Remove the screws 06H-450 and the washers 06H-460 from the aft side
wall assembly 06H-010.
(b) Remove the studs 06H-260 and the washers 06H-250 from the oxygen
container assy cover 06H-180.
(c) Remove the screws 06H-200, the nuts 06H-210 and the oxygen container assy
cover 06H-180 from the angle 06H-190.
(d) Remove the screws 06H-240, the washers 06H-250 and the angle 06H-190
from the aft side wall assembly 06H-010.
(e) Remove the ground cable from the oxygen container assy 06H-230.
(f) Remove the screws 06H-240, the washers 06H-250 and the oxygen container
assy 06H-230 from the angles 06H-220.
(g) Remove the screws 06H-240, the washers 06H-250 and the angles 06H-220
from the aft side wall assembly 06H-010.
(h) Remove the screws 06H-310, the washers 06H-250 and the angle 06H-340
from the aft side wall assembly 06H-010.
(j) Remove the screws 06H-350 and the single door emergency unlocking device
assembly 06H-360 from the post assembly 06H-270.
(k) Disassemble the single door emergency unlocking device assembly 06H-360
as follows:
1 Remove the bolt 06H-420 and the emergency unlocking device strike
06H-380 from the emergency unlocking device housing 06H-370.
For Myanmar Airways (MMA) use only
2 Remove the pin 06H-400, the snap catch 06H-410 and the emergency
unlocking device pivot 06H-390 from the emergency unlocking device
housing 06H-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06H-410 and the pin 06H-400.
(l) Remove the caps 06H-320, the screws 06H-310, 06H-330, the washers
06H-250 and the post assembly 06H-270.
1 Remove the screws 06H-280 and the plates 06H-300 from the post
assembly 06H-270.
(n) Remove the screws 06H-040, 06H-050 and the fittings 06H-020, 06H-030.
SUBTASK 25-41-58-010-016-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3048
For Myanmar Airways (MMA) use only
1 Remove the security pins 06H-160 from the handle assemblies 06H-140.
2 Remove the handle assemblies 06H-140 from the aft side wall assembly
06H-010.
3 Remove the special screws 06H-150 and the special washers 06H-170
from the aft side wall assembly 06H-010.
(b) Remove the studs 06H-260 and the washers 06H-250 from the oxygen
container assy cover 06H-180.
(c) Remove the screws 06H-200, the nuts 06H-210 and the oxygen container assy
cover 06H-180 from the angle 06H-190.
(d) Remove the screws 06H-240, the washers 06H-250 and the angle 06H-190
from the aft side wall assembly 06H-010.
(e) Remove the ground cable from the oxygen container assy 06H-230.
(f) Remove the screws 06H-240, 06H-245, the washers 06H-250 and the oxygen
container assy 06H-230 from the angles 06H-220.
(g) Remove the screws 06H-240, the washers 06H-250 and the angles 06H-220
from the aft side wall assembly 06H-010.
(h) Remove the screws 06H-310, the washers 06H-250 and the angle 06H-340
from the aft side wall assembly 06H-010.
(j) Remove the screws 06H-350 and the single door emergency unlocking device
assembly 06H-360 from the post assembly 06H-270.
(k) Disassemble the single door emergency unlocking device assembly 06H-360
as follows:
1 Remove the bolt 06H-420 and the emergency unlocking device strike
06H-380 from the emergency unlocking device housing 06H-370.
For Myanmar Airways (MMA) use only
2 Remove the pin 06H-400, the snap catch 06H-410 and the emergency
unlocking device pivot 06H-390 from the emergency unlocking device
housing 06H-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06H-410 and the pin 06H-400.
(l) Remove the caps 06H-320, the screws 06H-310, 06H-330, the washers
06H-250 and the post assembly 06H-270.
1 Remove the screws 06H-280 and the plates 06H-300 from the post
assembly 06H-270.
(n) Remove the screws 06H-490 and the toilet seat-cover dispenser 06H-480 from
the aft side wall assembly 06H-010.
(p) Remove the screws 06H-040, 06H-050 and the fittings 06H-020, 06H-030.
SUBTASK 25-41-58-010-016-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3049
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06H-160 from the handle assemblies 06H-140.
2 Remove the handle assemblies 06H-140 from the aft side wall assembly
06H-010.
3 Remove the special screws 06H-150 and the special washers 06H-170
from the aft side wall assembly 06H-010.
(b) Remove the studs 06H-260 and the washers 06H-250 from the oxygen
container assy cover 06H-180.
(c) Remove the screws 06H-200, the nuts 06H-210 and the oxygen container assy
cover 06H-180 from the angle 06H-190.
(d) Remove the screws 06H-240, the washers 06H-250 and the angle 06H-190
from the aft side wall assembly 06H-010.
(e) Remove the ground cable from the oxygen container assy 06H-230.
(f) Remove the screws 06H-240, the washers 06H-250 and the oxygen container
assy 06H-230 from the angles 06H-220.
(g) Remove the screws 06H-240, the washers 06H-250 and the angles 06H-220
from the aft side wall assembly 06H-010.
(h) Remove the screws 06H-310, the washers 06H-250 and the angle 06H-340
from the aft side wall assembly 06H-010.
(j) Remove the screws 06H-350 and the single door emergency unlocking device
assembly 06H-360 from the post assembly 06H-270.
(k) Disassemble the single door emergency unlocking device assembly 06H-360
as follows:
1 Remove the bolt 06H-420 and the emergency unlocking device strike
06H-380 from the emergency unlocking device housing 06H-370.
2 Remove the pin 06H-400, the snap catch 06H-410 and the emergency
unlocking device pivot 06H-390 from the emergency unlocking device
housing 06H-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06H-410 and the pin 06H-400.
(l) Remove the caps 06H-320, the screws 06H-310, 06H-330, the washers
06H-250 and the post assembly 06H-270.
1 Remove the screws 06H-280 and the plates 06H-300 from the post
assembly 06H-270.
(n) Remove the screws 06H-490 and the toilet seat-cover dispenser 06H-480 from
the aft side wall assembly 06H-010.
(p) Remove the screws 06H-040, 06H-050 and the fittings 06H-020, 06H-030.
SUBTASK 25-41-58-010-016-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3050
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06H-160 from the handle assemblies 06H-140.
2 Remove the handle assemblies 06H-140 from the aft side wall assembly
06H-010.
3 Remove the special screws 06H-150 and the special washers 06H-170
from the aft side wall assembly 06H-010.
(b) Remove the studs 06H-260 and the washers 06H-250 from the oxygen
container assy cover 06H-180.
(c) Remove the screws 06H-200, the nuts 06H-210 and the oxygen container assy
cover 06H-180 from the angle 06H-190.
(d) Remove the screws 06H-240, the washers 06H-250 and the angle 06H-190
from the aft side wall assembly 06H-010.
(e) Remove the ground cable from the oxygen container assy 06H-230.
(f) Remove the screws 06H-240, 06H-245, the washers 06H-250 and the oxygen
container assy 06H-230 from the angles 06H-220.
(g) Remove the screws 06H-240, the washers 06H-250 and the angles 06H-220
from the aft side wall assembly 06H-010.
(h) Remove the screws 06H-310, the washers 06H-250 and the angle 06H-340
from the aft side wall assembly 06H-010.
(j) Remove the screws 06H-350 and the single door emergency unlocking device
assembly 06H-360 from the post assembly 06H-270.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06H-360
as follows:
1 Remove the bolt 06H-420 and the emergency unlocking device strike
06H-380 from the emergency unlocking device housing 06H-370.
2 Remove the pin 06H-400, the snap catch 06H-410 and the emergency
unlocking device pivot 06H-390 from the emergency unlocking device
housing 06H-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06H-410 and the pin 06H-400.
(l) Remove the caps 06H-320, the screws 06H-310, 06H-330, the washers
06H-250 and the post assembly 06H-270.
1 Remove the screws 06H-280 and the plates 06H-300 from the post
assembly 06H-270.
(n) Remove the screws 06H-040, 06H-050 and the fittings 06H-020, 06H-030.
SUBTASK 25-41-58-010-016-E01
D2549030710800 R225401136-002
(0) Removal of the Side Wall (06H-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3051
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06H-160 from the handle assemblies 06H-140.
2 Remove the handle assemblies 06H-140 from the aft side wall assembly
06H-010.
3 Remove the special screws 06H-150 and the special washers 06H-170
from the aft side wall assembly 06H-010.
(b) Remove the studs 06H-260 and the washers 06H-250 from the oxygen
container assy cover 06H-180.
(c) Remove the screws 06H-200, the nuts 06H-210 and the oxygen container assy
cover 06H-180 from the angle 06H-190.
(d) Remove the screws 06H-240, the washers 06H-250 and the angle 06H-190
from the aft side wall assembly 06H-010.
(e) Remove the ground cable from the oxygen container assy 06H-230.
(f) Remove the screws 06H-240, 06H-245, the washers 06H-250 and the oxygen
container assy 06H-230 from the angles 06H-220.
(g) Remove the screws 06H-240, the washers 06H-250 and the angles 06H-220
from the aft side wall assembly 06H-010.
(h) Remove the screws 06H-310, the washers 06H-250 and the angle 06H-340
from the aft side wall assembly 06H-010.
(j) Remove the screws 06H-350 and the single door emergency unlocking device
assembly 06H-360 from the post assembly 06H-270.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06H-360
as follows:
1 Remove the bolt 06H-420 and the emergency unlocking device strike
06H-380 from the emergency unlocking device housing 06H-370.
2 Remove the pin 06H-400, the snap catch 06H-410 and the emergency
unlocking device pivot 06H-390 from the emergency unlocking device
housing 06H-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06H-410 and the pin 06H-400.
(l) Remove the caps 06H-320, the screws 06H-310, 06H-330, the washers
06H-250 and the post assembly 06H-270.
1 Remove the screws 06H-280 and the plates 06H-300 from the post
assembly 06H-270.
(n) Remove the screws 06H-040, 06H-050 and the fittings 06H-020, 06H-030.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-804-K01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-017-A01
For Myanmar Airways (MMA) use only
D2549010410600 D2549020901000
(1) Removal of the Side Wall (06J-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3052
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06J-160 from the handle assemblies 06J-140.
2 Remove the handle assemblies 06J-140 from the aft side wall assembly
06J-010.
3 Remove the special screws 06J-150 and the special washers 06J-170
from the aft side wall assembly 06J-010.
(b) Remove the studs 06J-260 and the washers 06J-250 from the oxygen container
assy cover 06J-180.
(c) Remove the screws 06J-200, the nuts 06J-210 and the oxygen container assy
cover 06J-180 from the angle 06J-190.
(d) Remove the screws 06J-240, the washers 06J-250 and the angle 06J-190 from
the aft side wall assembly 06J-010.
(e) Remove the ground cable from the oxygen container assy 06J-230.
(f) Remove the screws 06J-240, the washers 06J-250 and the oxygen container
assy 06J-230 from the angles 06J-220.
(g) Remove the screws 06J-240, the washers 06J-250 and the angles 06J-220
from the aft side wall assembly 06J-010.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06J-310, the washers 06J-250 and the angle 06J-340 from
the aft side wall assembly 06J-010.
(j) Remove the screws 06J-350 and the single door emergency unlocking device
assembly 06J-360 from the post assembly 06J-270.
(k) Disassemble the single door emergency unlocking device assembly 06J-360
as follows:
1 Remove the bolt 06J-420 and the emergency unlocking device strike
06J-380 from the emergency unlocking device housing 06J-370.
2 Remove the pin 06J-400, the snap catch 06J-410 and the emergency
unlocking device pivot 06J-390 from the emergency unlocking device
housing 06J-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06J-410 and the pin 06J-400.
(l) Remove the caps 06J-320, the screws 06J-310, 06J-330, the washers 06J-250
and the post assembly 06J-270.
1 Remove the screws 06J-280 and the plates 06J-300 from the post
assembly 06J-270.
(n) Remove the screws 06J-440 and the toilet seat-cover dispenser 06J-430 from
the aft side wall assembly 06J-010.
For Myanmar Airways (MMA) use only
(p) Remove the screw 06J-351 and the coat hook 06J-450 from the aft side wall
assembly 06J-010.
(q) Remove the screws 06J-040, 06J-050 and the fittings 06J-020, 06J-030.
SUBTASK 25-41-58-010-017-B01
D2549020901800 R225401822-004
(0) Removal of the Side Wall (06J-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3053
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06J-160 from the handle assemblies 06J-140.
2 Remove the handle assemblies 06J-140 from the aft side wall assembly
06J-010.
3 Remove the special screws 06J-150 and the special washers 06J-170
from the aft side wall assembly 06J-010.
(b) Remove the studs 06J-260 and the washers 06J-250 from the oxygen container
assy cover 06J-180.
(c) Remove the screws 06J-200, the nuts 06J-210 and the oxygen container assy
cover 06J-180 from the angle 06J-190.
(d) Remove the screws 06J-240, the washers 06J-250 and the angle 06J-190 from
the aft side wall assembly 06J-010.
For Myanmar Airways (MMA) use only
(e) Remove the ground cable from the oxygen container assy 06J-230.
(f) Remove the screws 06J-240, 06J-245, the washers 06J-250 and the oxygen
container assy 06J-230 from the angles 06J-220.
(g) Remove the screws 06J-240, the washers 06J-250 and the angles 06J-220
from the aft side wall assembly 06J-010.
(h) Remove the screws 06J-310, the washers 06J-250 and the angle 06J-340 from
the aft side wall assembly 06J-010.
(j) Remove the screws 06J-350 and the single door emergency unlocking device
assembly 06J-360 from the post assembly 06J-270.
(k) Disassemble the single door emergency unlocking device assembly 06J-360
as follows:
1 Remove the bolt 06J-420 and the emergency unlocking device strike
06J-380 from the emergency unlocking device housing 06J-370.
2 Remove the pin 06J-400, the snap catch 06J-410 and the emergency
unlocking device pivot 06J-390 from the emergency unlocking device
housing 06J-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06J-410 and the pin 06J-400.
(l) Remove the caps 06J-320, the screws 06J-310, 06J-330, the washers 06J-250
and the post assembly 06J-270.
1 Remove the screws 06J-280 and the plates 06J-300 from the post
assembly 06J-270.
(n) Remove the screw 06J-351 and the coat hook 06J-450 from the aft side wall
assembly 06J-010.
(p) Remove the screws 06J-040, 06J-050 and the fittings 06J-020, 06J-030.
SUBTASK 25-41-58-010-017-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3054
For Myanmar Airways (MMA) use only
1 Remove the security pins 06J-160 from the handle assemblies 06J-140.
2 Remove the handle assemblies 06J-140 from the aft side wall assembly
06J-010.
3 Remove the special screws 06J-150 and the special washers 06J-170
from the aft side wall assembly 06J-010.
(b) Remove the studs 06J-260 and the washers 06J-250 from the oxygen container
assy cover 06J-180.
(c) Remove the screws 06J-200, the nuts 06J-210 and the oxygen container assy
cover 06J-180 from the angle 06J-190.
(d) Remove the screws 06J-240, the washers 06J-250 and the angle 06J-190 from
the aft side wall assembly 06J-010.
(e) Remove the ground cable from the oxygen container assy 06J-230.
(f) Remove the screws 06J-240, the washers 06J-250 and the oxygen container
assy 06J-230 from the angles 06J-220.
(g) Remove the screws 06J-240, the washers 06J-250 and the angles 06J-220
from the aft side wall assembly 06J-010.
(h) Remove the screws 06J-310, the washers 06J-250 and the angle 06J-340 from
the aft side wall assembly 06J-010.
(j) Remove the screws 06J-350 and the single door emergency unlocking device
assembly 06J-360 from the post assembly 06J-270.
(k) Disassemble the single door emergency unlocking device assembly 06J-360
as follows:
1 Remove the bolt 06J-420 and the emergency unlocking device strike
06J-380 from the emergency unlocking device housing 06J-370.
For Myanmar Airways (MMA) use only
2 Remove the pin 06J-400, the snap catch 06J-410 and the emergency
unlocking device pivot 06J-390 from the emergency unlocking device
housing 06J-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06J-410 and the pin 06J-400.
(l) Remove the caps 06J-320, the screws 06J-310, 06J-330, the washers 06J-250
and the post assembly 06J-270.
1 Remove the screws 06J-280 and the plates 06J-300 from the post
assembly 06J-270.
(n) Remove the screws 06J-440 and the toilet seat-cover dispenser 06J-430 from
the aft side wall assembly 06J-010.
(p) Remove the screws 06J-040, 06J-050 and the fittings 06J-020, 06J-030.
SUBTASK 25-41-58-010-017-D01
D2549040503800 R225401673-014
(0) Removal of the Side Wall (06J-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Assembly 350-802-A01
Table 3055
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06J-160 from the handle assemblies 06J-140.
2 Remove the handle assemblies 06J-140 from the aft side wall assembly
06J-010.
3 Remove the special screws 06J-150 and the special washers 06J-170
from the aft side wall assembly 06J-010.
(b) Remove the studs 06J-260 and the washers 06J-250 from the oxygen container
assy cover 06J-180.
(c) Remove the screws 06J-200, the nuts 06J-210 and the oxygen container assy
cover 06J-180 from the angle 06J-190.
(d) Remove the screws 06J-240, the washers 06J-250 and the angle 06J-190 from
the aft side wall assembly 06J-010.
(e) Remove the ground cable from the oxygen container assy 06J-230.
(f) Remove the screws 06J-240, the washers 06J-250 and the oxygen container
assy 06J-230 from the angles 06J-220.
(g) Remove the screws 06J-240, the washers 06J-250 and the angles 06J-220
from the aft side wall assembly 06J-010.
(h) Remove the screws 06J-310, the washers 06J-250 and the angle 06J-340 from
the aft side wall assembly 06J-010.
(j) Remove the screws 06J-350 and the single door emergency unlocking device
assembly 06J-360 from the post assembly 06J-270.
(k) Disassemble the single door emergency unlocking device assembly 06J-360
as follows:
1 Remove the bolt 06J-420 and the emergency unlocking device strike
06J-380 from the emergency unlocking device housing 06J-370.
2 Remove the pin 06J-400, the snap catch 06J-410 and the emergency
unlocking device pivot 06J-390 from the emergency unlocking device
housing 06J-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06J-410 and the pin 06J-400.
(l) Remove the caps 06J-320, the screws 06J-310, 06J-330, the washers 06J-250
and the post assembly 06J-270.
1 Remove the screws 06J-280 and the plates 06J-300 from the post
assembly 06J-270.
(n) Remove the screws 06J-440 and the toilet seat-cover dispenser 06J-430 from
the aft side wall assembly 06J-010.
(p) Remove the screws 06J-040, 06J-050 and the fittings 06J-020, 06J-030.
SUBTASK 25-41-58-010-017-E01
D2549020900800 D2549040504000
(0) Removal of the Side Wall (06J-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3056
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06J-160 from the handle assemblies 06J-140.
2 Remove the handle assemblies 06J-140 from the aft side wall assembly
06J-010.
3 Remove the special screws 06J-150 and the special washers 06J-170
from the aft side wall assembly 06J-010.
(b) Remove the studs 06J-260 and the washers 06J-250 from the oxygen container
assy cover 06J-180.
(c) Remove the screws 06J-200, the nuts 06J-210 and the oxygen container assy
cover 06J-180 from the angle 06J-190.
(d) Remove the screws 06J-240, the washers 06J-250 and the angle 06J-190 from
the aft side wall assembly 06J-010.
(e) Remove the ground cable from the oxygen container assy 06J-230.
(f) Remove the screws 06J-240, the washers 06J-250 and the oxygen container
assy 06J-230 from the angles 06J-220.
(g) Remove the screws 06J-240, the washers 06J-250 and the angles 06J-220
from the aft side wall assembly 06J-010.
(h) Remove the screws 06J-310, the washers 06J-250 and the angle 06J-340 from
the aft side wall assembly 06J-010.
(j) Remove the screws 06J-350 and the single door emergency unlocking device
assembly 06J-360 from the post assembly 06J-270.
(k) Disassemble the single door emergency unlocking device assembly 06J-360
as follows:
1 Remove the bolt 06J-420 and the emergency unlocking device strike
06J-380 from the emergency unlocking device housing 06J-370.
2 Remove the pin 06J-400, the snap catch 06J-410 and the emergency
unlocking device pivot 06J-390 from the emergency unlocking device
housing 06J-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06J-410 and the pin 06J-400.
(l) Remove the caps 06J-320, the screws 06J-310, 06J-330, the washers 06J-250
and the post assembly 06J-270.
1 Remove the screws 06J-280 and the plates 06J-300 from the post
assembly 06J-270.
(n) Remove the screws 06J-040, 06J-050 and the fittings 06J-020, 06J-030.
SUBTASK 25-41-58-010-017-F01
D2549020903800 D2549026000800
(0) Removal of the Side Wall (06J-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3057
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06J-160 from the handle assemblies 06J-140.
2 Remove the handle assemblies 06J-140 from the aft side wall assembly
06J-010.
3 Remove the special screws 06J-150 and the special washers 06J-170
from the aft side wall assembly 06J-010.
(b) Remove the studs 06J-260 and the washers 06J-250 from the oxygen container
assy cover 06J-180.
(c) Remove the screws 06J-200, the nuts 06J-210 and the oxygen container assy
cover 06J-180 from the angle 06J-190.
(d) Remove the screws 06J-240, the washers 06J-250 and the angle 06J-190 from
the aft side wall assembly 06J-010.
(e) Remove the ground cable from the oxygen container assy 06J-230.
(f) Remove the screws 06J-240, the washers 06J-250 and the oxygen container
assy 06J-230 from the angles 06J-220.
(g) Remove the screws 06J-240, the washers 06J-250 and the angles 06J-220
from the aft side wall assembly 06J-010.
(h) Remove the screws 06J-310, the washers 06J-250 and the angle 06J-340 from
the aft side wall assembly 06J-010.
(j) Remove the screws 06J-350 and the single door emergency unlocking device
assembly 06J-360 from the post assembly 06J-270.
(k) Disassemble the single door emergency unlocking device assembly 06J-360
as follows:
1 Remove the bolt 06J-420 and the emergency unlocking device strike
06J-380 from the emergency unlocking device housing 06J-370.
2 Remove the pin 06J-400, the snap catch 06J-410 and the emergency
unlocking device pivot 06J-390 from the emergency unlocking device
housing 06J-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06J-410 and the pin 06J-400.
(l) Remove the caps 06J-320, the screws 06J-310, 06J-330, the washers 06J-250
and the post assembly 06J-270.
1 Remove the screws 06J-280 and the plates 06J-300 from the post
assembly 06J-270.
(n) Remove the screws 06J-040, 06J-050 and the fittings 06J-020, 06J-030.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-804-L01
A. General
For Myanmar Airways (MMA) use only
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-018-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3058
For Myanmar Airways (MMA) use only
1 Remove the security pins 06K-480 from the handle assemblies 06K-460.
2 Remove the handle assemblies 06K-460 from the aft side wall assembly
06K-010.
3 Remove the special screws 06K-470 and the special washers 06K-490
from the aft side wall assembly 06K-010.
(b) Remove the studs 06K-270 and the washers 06K-260 from the oxygen
container assy cover 06K-190.
(c) Remove the screws 06K-210, the nuts 06K-220 and the oxygen container assy
cover 06K-190 from the angle 06K-200.
(d) Remove the screws 06K-250, the washers 06K-260 and the angle 06K-200
from the aft side wall assembly 06K-010.
(e) Remove the ground cable from the oxygen container assy 06K-240.
(f) Remove the screws 06K-250, the washers 06K-260 and the oxygen container
assy 06K-240 from the angles 06K-230.
(g) Remove the screws 06K-250, the washers 06K-260 and the angles 06K-230
from the aft side wall assembly 06K-010.
(h) Remove the screws 06K-320, the washers 06K-260 and the angle 06K-350
from the aft side wall assembly 06K-010.
(j) Remove the screws 06K-360 and the single door emergency unlocking device
assembly 06K-370 from the post assembly 06K-280.
(k) Disassemble the single door emergency unlocking device assembly 06K-370
as follows:
1 Remove the bolt 06K-430 and the emergency unlocking device strike
06K-390 from the emergency unlocking device housing 06K-380.
For Myanmar Airways (MMA) use only
2 Remove the pin 06K-410, the snap catch 06K-420 and the emergency
unlocking device pivot 06K-400 from the emergency unlocking device
housing 06K-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06K-420 and the pin 06K-410.
(l) Remove the caps 06K-330, the screws 06K-320, 06K-340, the washers
06K-260 and the post assembly 06K-280.
1 Remove the screws 06K-290 and the plates 06K-310 from the post
assembly 06K-280.
(n) Remove the screws 06K-450 and the toilet seat-cover dispenser 06K-440 from
the aft side wall assembly 06K-010.
(p) Remove the screw 06K-361 and the coat hook 06K-500 from the aft side wall
assembly 06K-010.
(q) Remove the screws 06K-040, 06K-050 and the fittings 06K-020, 06K-030.
SUBTASK 25-41-58-010-018-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3059
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06K-480 from the handle assemblies 06K-460.
2 Remove the handle assemblies 06K-460 from the aft side wall assembly
06K-010.
3 Remove the special screws 06K-470 and the special washers 06K-490
from the aft side wall assembly 06K-010.
(b) Remove the studs 06K-270 and the washers 06K-260 from the oxygen
container assy cover 06K-190.
(c) Remove the screws 06K-210, the nuts 06K-220 and the oxygen container assy
cover 06K-190 from the angle 06K-200.
(d) Remove the screws 06K-250, 06K-255, the washers 06K-260 and the angle
06K-200 from the aft side wall assembly 06K-010.
(e) Remove the ground cable from the oxygen container assy 06K-240.
(f) Remove the screws 06K-250, the washers 06K-260 and the oxygen container
assy 06K-240 from the angles 06K-230.
(g) Remove the screws 06K-250, the washers 06K-260 and the angles 06K-230
from the aft side wall assembly 06K-010.
(h) Remove the screws 06K-320, the washers 06K-260 and the angle 06K-350
from the aft side wall assembly 06K-010.
(j) Remove the screws 06K-360 and the single door emergency unlocking device
assembly 06K-370 from the post assembly 06K-280.
(k) Disassemble the single door emergency unlocking device assembly 06K-370
as follows:
1 Remove the bolt 06K-430 and the emergency unlocking device strike
06K-390 from the emergency unlocking device housing 06K-380.
2 Remove the pin 06K-410, the snap catch 06K-420 and the emergency
unlocking device pivot 06K-400 from the emergency unlocking device
housing 06K-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06K-420 and the pin 06K-410.
(l) Remove the caps 06K-330, the screws 06K-320, 06K-340, the washers
06K-260 and the post assembly 06K-280.
1 Remove the screws 06K-290 and the plates 06K-310 from the post
assembly 06K-280.
(n) Remove the screw 06K-361 and the coat hook 06K-500 from the aft side wall
assembly 06K-010.
(p) Remove the screws 06K-040, 06K-050 and the fittings 06K-020, 06K-030.
SUBTASK 25-41-58-010-018-C01
D2549020905200 D2549030807200
(0) Removal of the Side Wall (06K-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
PART
NAME
Table 3060
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06K-480 from the handle assemblies 06K-460.
2 Remove the handle assemblies 06K-460 from the aft side wall assembly
06K-010.
3 Remove the special screws 06K-470 and the special washers 06K-490
from the aft side wall assembly 06K-010.
(b) Remove the studs 06K-270 and the washers 06K-260 from the oxygen
container assy cover 06K-190.
(c) Remove the screws 06K-210, the nuts 06K-220 and the oxygen container assy
cover 06K-190 from the angle 06K-200.
(d) Remove the screws 06K-250, the washers 06K-260 and the angle 06K-200
from the aft side wall assembly 06K-010.
(e) Remove the ground cable from the oxygen container assy 06K-240.
(f) Remove the screws 06K-250, the washers 06K-260 and the oxygen container
assy 06K-240 from the angles 06K-230.
(g) Remove the screws 06K-250, the washers 06K-260 and the angles 06K-230
from the aft side wall assembly 06K-010.
(h) Remove the screws 06K-320, the washers 06K-260 and the angle 06K-350
from the aft side wall assembly 06K-010.
(j) Remove the screws 06K-360 and the single door emergency unlocking device
assembly 06K-370 from the post assembly 06K-280.
(k) Disassemble the single door emergency unlocking device assembly 06K-370
as follows:
For Myanmar Airways (MMA) use only
1 Remove the bolt 06K-430 and the emergency unlocking device strike
06K-390 from the emergency unlocking device housing 06K-380.
2 Remove the pin 06K-410, the snap catch 06K-420 and the emergency
unlocking device pivot 06K-400 from the emergency unlocking device
housing 06K-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06K-420 and the pin 06K-410.
(l) Remove the caps 06K-330, the screws 06K-320, 06K-340, the washers
06K-260 and the post assembly 06K-280.
1 Remove the screws 06K-290 and the plates 06K-310 from the post
assembly 06K-280.
(n) Remove the screws 06K-450 and the toilet seat-cover dispenser 06K-440 from
the aft side wall assembly 06K-010.
(p) Remove the screws 06K-040, 06K-050 and the fittings 06K-020, 06K-030.
SUBTASK 25-41-58-010-018-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
For Myanmar Airways (MMA) use only
Table 3061
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06K-480 from the handle assemblies 06K-460.
2 Remove the handle assemblies 06K-460 from the aft side wall assembly
06K-010.
3 Remove the special screws 06K-470 and the special washers 06K-490
from the aft side wall assembly 06K-010.
(b) Remove the studs 06K-270 and the washers 06K-260 from the oxygen
container assy cover 06K-190.
(c) Remove the screws 06K-210, the nuts 06K-220 and the oxygen container assy
cover 06K-190 from the angle 06K-200.
(d) Remove the screws 06K-250, the washers 06K-260 and the angle 06K-200
from the aft side wall assembly 06K-010.
(e) Remove the ground cable from the oxygen container assy 06K-240.
(f) Remove the screws 06K-250, the washers 06K-260 and the oxygen container
assy 06K-240 from the angles 06K-230.
(g) Remove the screws 06K-250, the washers 06K-260 and the angles 06K-230
from the aft side wall assembly 06K-010.
(h) Remove the screws 06K-320, the washers 06K-260 and the angle 06K-350
from the aft side wall assembly 06K-010.
(j) Remove the screws 06K-360 and the single door emergency unlocking device
assembly 06K-370 from the post assembly 06K-280.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06K-370
as follows:
1 Remove the bolt 06K-430 and the emergency unlocking device strike
06K-390 from the emergency unlocking device housing 06K-380.
2 Remove the pin 06K-410, the snap catch 06K-420 and the emergency
unlocking device pivot 06K-400 from the emergency unlocking device
housing 06K-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06K-420 and the pin 06K-410.
(l) Remove the caps 06K-330, the screws 06K-320, 06K-340, the washers
06K-260 and the post assembly 06K-280.
1 Remove the screws 06K-290 and the plates 06K-310 from the post
assembly 06K-280.
(n) Remove the screws 06K-450 and the toilet seat-cover dispenser 06K-440 from
the aft side wall assembly 06K-010.
(p) Remove the screws 06K-040, 06K-050 and the fittings 06K-020, 06K-030.
SUBTASK 25-41-58-010-018-E01
NOTE: See TABLE for the references for the replacement procedures of
For Myanmar Airways (MMA) use only
Table 3062
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the setscrews 06K-180 and the handle 06K-150 from the screws
06K-160.
2 Remove the screws 06K-160 and the washers 06K-170 from the aft side
wall assembly 06K-010.
(b) Remove the studs 06K-270 and the washers 06K-260 from the oxygen
container assy cover 06K-190.
(c) Remove the screws 06K-210, the nuts 06K-220 and the oxygen container assy
cover 06K-190 from the angle 06K-200.
(d) Remove the screws 06K-250, the washers 06K-260 and the angle 06K-200
from the aft side wall assembly 06K-010.
(e) Remove the ground cable from the oxygen container assy 06K-240.
(f) Remove the screws 06K-250, 06K-255, the washers 06K-260 and the oxygen
container assy 06K-240 from the angles 06K-230.
(g) Remove the screws 06K-250, the washers 06K-260 and the angles 06K-230
from the aft side wall assembly 06K-010.
(h) Remove the screws 06K-320, the washers 06K-260 and the angle 06K-350
from the aft side wall assembly 06K-010.
(j) Remove the screws 06K-360 and the single door emergency unlocking device
assembly 06K-370 from the post assembly 06K-280.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06K-370
as follows:
1 Remove the bolt 06K-430 and the emergency unlocking device strike
06K-390 from the emergency unlocking device housing 06K-380.
2 Remove the pin 06K-410, the snap catch 06K-420 and the emergency
unlocking device pivot 06K-400 from the emergency unlocking device
housing 06K-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06K-420 and the pin 06K-410.
(l) Remove the caps 06K-330, the screws 06K-320, 06K-340, the washers
06K-260 and the post assembly 06K-280.
1 Remove the screws 06K-290 and the plates 06K-310 from the post
assembly 06K-280.
(n) Remove the screws 06K-450 and the toilet seat-cover dispenser 06K-440 from
the aft side wall assembly 06K-010.
(p) Remove the screws 06K-040, 06K-050 and the fittings 06K-020, 06K-030.
SUBTASK 25-41-58-010-018-F01
NOTE: See TABLE for the references for the replacement procedures of
For Myanmar Airways (MMA) use only
Table 3063
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the setscrews 06K-180 and the handle 06K-150 from the screws
06K-160.
2 Remove the screws 06K-160 and the washers 06K-170 from the aft side
wall assembly 06K-010.
(b) Remove the studs 06K-270 and the washers 06K-260 from the oxygen
container assy cover 06K-190.
(c) Remove the screws 06K-210, the nuts 06K-220 and the oxygen container assy
cover 06K-190 from the angle 06K-200.
(d) Remove the screws 06K-250, the washers 06K-260 and the angle 06K-200
from the aft side wall assembly 06K-010.
(e) Remove the ground cable from the oxygen container assy 06K-240.
(f) Remove the screws 06K-250, the washers 06K-260 and the oxygen container
assy 06K-240 from the angles 06K-230.
(g) Remove the screws 06K-250, the washers 06K-260 and the angles 06K-230
from the aft side wall assembly 06K-010.
(h) Remove the screws 06K-320, the washers 06K-260 and the angle 06K-350
from the aft side wall assembly 06K-010.
(j) Remove the screws 06K-360 and the single door emergency unlocking device
assembly 06K-370 from the post assembly 06K-280.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06K-370
as follows:
1 Remove the bolt 06K-430 and the emergency unlocking device strike
06K-390 from the emergency unlocking device housing 06K-380.
2 Remove the pin 06K-410, the snap catch 06K-420 and the emergency
unlocking device pivot 06K-400 from the emergency unlocking device
housing 06K-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06K-420 and the pin 06K-410.
(l) Remove the caps 06K-330, the screws 06K-320, 06K-340, the washers
06K-260 and the post assembly 06K-280.
1 Remove the screws 06K-290 and the plates 06K-310 from the post
assembly 06K-280.
(n) Remove the screws 06K-040, 06K-050 and the fittings 06K-020, 06K-030.
SUBTASK 25-41-58-010-018-G01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
For Myanmar Airways (MMA) use only
Table 3064
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06K-480 from the handle assemblies 06K-460.
2 Remove the handle assemblies 06K-460 from the aft side wall assembly
06K-010.
3 Remove the special screws 06K-470 and the special washers 06K-490
from the aft side wall assembly 06K-010.
(b) Remove the studs 06K-270 and the washers 06K-260 from the oxygen
container assy cover 06K-190.
(c) Remove the screws 06K-210, the nuts 06K-220 and the oxygen container assy
cover 06K-190 from the angle 06K-200.
(d) Remove the screws 06K-250, the washers 06K-260 and the angle 06K-200
from the aft side wall assembly 06K-010.
(e) Remove the ground cable from the oxygen container assy 06K-240.
(f) Remove the screws 06K-250, 06K-255, the washers 06K-260 and the oxygen
container assy 06K-240 from the angles 06K-230.
(g) Remove the screws 06K-250, the washers 06K-260 and the angles 06K-230
from the aft side wall assembly 06K-010.
(h) Remove the screws 06K-320, the washers 06K-260 and the angle 06K-350
from the aft side wall assembly 06K-010.
(j) Remove the screws 06K-360 and the single door emergency unlocking device
assembly 06K-370 from the post assembly 06K-280.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06K-370
as follows:
1 Remove the bolt 06K-430 and the emergency unlocking device strike
06K-390 from the emergency unlocking device housing 06K-380.
2 Remove the pin 06K-410, the snap catch 06K-420 and the emergency
unlocking device pivot 06K-400 from the emergency unlocking device
housing 06K-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06K-420 and the pin 06K-410.
(l) Remove the caps 06K-330, the screws 06K-320, 06K-340, the washers
06K-260 and the post assembly 06K-280.
1 Remove the screws 06K-290 and the plates 06K-310 from the post
assembly 06K-280.
(n) Remove the screws 06K-040, 06K-050 and the fittings 06K-020, 06K-030.
SUBTASK 25-41-58-010-018-H01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3065
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06K-480 from the handle assemblies 06K-460.
2 Remove the handle assemblies 06K-460 from the aft side wall assembly
06K-010.
3 Remove the special screws 06K-470 and the special washers 06K-490
from the aft side wall assembly 06K-010.
(b) Remove the studs 06K-270 and the washers 06K-260 from the oxygen
container assy cover 06K-190.
(c) Remove the screws 06K-210, the nuts 06K-220 and the oxygen container assy
cover 06K-190 from the angle 06K-200.
(d) Remove the screws 06K-250, the washers 06K-260 and the angle 06K-200
from the aft side wall assembly 06K-010.
(e) Remove the ground cable from the oxygen container assy 06K-240.
(f) Remove the screws 06K-250, the washers 06K-260 and the oxygen container
assy 06K-240 from the angles 06K-230.
(g) Remove the screws 06K-250, the washers 06K-260 and the angles 06K-230
from the aft side wall assembly 06K-010.
(h) Remove the screws 06K-320, the washers 06K-260 and the angle 06K-350
from the aft side wall assembly 06K-010.
(j) Remove the screws 06K-360 and the single door emergency unlocking device
assembly 06K-370 from the post assembly 06K-280.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06K-370
as follows:
1 Remove the bolt 06K-430 and the emergency unlocking device strike
06K-390 from the emergency unlocking device housing 06K-380.
2 Remove the pin 06K-410, the snap catch 06K-420 and the emergency
unlocking device pivot 06K-400 from the emergency unlocking device
housing 06K-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06K-420 and the pin 06K-410.
(l) Remove the caps 06K-330, the screws 06K-320, 06K-340, the washers
06K-260 and the post assembly 06K-280.
1 Remove the screws 06K-290 and the plates 06K-310 from the post
assembly 06K-280.
(n) Remove the screws 06K-040, 06K-050 and the fittings 06K-020, 06K-030.
SUBTASK 25-41-58-010-018-J01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3066
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06K-480 from the handle assemblies 06K-460.
2 Remove the handle assemblies 06K-460 from the aft side wall assembly
06K-010.
3 Remove the special screws 06K-470 and the special washers 06K-490
from the aft side wall assembly 06K-010.
(b) Remove the studs 06K-270 and the washers 06K-260 from the oxygen
container assy cover 06K-190.
(c) Remove the screws 06K-210, the nuts 06K-220 and the oxygen container assy
cover 06K-190 from the angle 06K-200.
(d) Remove the screws 06K-250, the washers 06K-260 and the angle 06K-200
from the aft side wall assembly 06K-010.
(e) Remove the ground cable from the oxygen container assy 06K-240.
(f) Remove the screws 06K-250, 06K-255, the washers 06K-260 and the oxygen
container assy 06K-240 from the angles 06K-230.
(g) Remove the screws 06K-250, the washers 06K-260 and the angles 06K-230
from the aft side wall assembly 06K-010.
(h) Remove the screws 06K-320, the washers 06K-260 and the angle 06K-350
from the aft side wall assembly 06K-010.
(j) Remove the screws 06K-360 and the single door emergency unlocking device
assembly 06K-370 from the post assembly 06K-280.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06K-370
as follows:
1 Remove the bolt 06K-430 and the emergency unlocking device strike
06K-390 from the emergency unlocking device housing 06K-380.
2 Remove the pin 06K-410, the snap catch 06K-420 and the emergency
unlocking device pivot 06K-400 from the emergency unlocking device
housing 06K-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06K-420 and the pin 06K-410.
(l) Remove the caps 06K-330, the screws 06K-320, 06K-340, the washers
06K-260 and the post assembly 06K-280.
1 Remove the screws 06K-290 and the plates 06K-310 from the post
assembly 06K-280.
(n) Remove the screws 06K-040, 06K-050 and the fittings 06K-020, 06K-030.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-804-M01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-019-A01
For Myanmar Airways (MMA) use only
D2549020907000
(1) Removal of the Side Wall (06L-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3067
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06L-320 from the handle assembly 06L-300.
2 Remove the handle assembly 06L-300 from the aft side wall assembly
06L-010.
3 Remove the special screws 06L-310 and the special washers 06L-330
from the aft side wall assembly 06L-010.
(b) Remove the screws 06L-440, the washers 06L-210 and the support 06L-340
from the aft side wall assembly 06L-010.
(c) Remove the studs 06L-220 and the washers 06L-210 from the oxygen
container assy cover 06L-140.
(d) Remove the screws 06L-160, the nuts 06L-170 and the oxygen container assy
cover 06L-140 from the angle 06L-150.
(e) Remove the screws 06L-200, the washers 06L-210 and the angle 06L-150
from the aft side wall assembly 06L-010.
(f) Remove the ground cable from the oxygen container assy 06L-190.
(g) Remove the screws 06L-200, the washers 06L-210 and the oxygen container
assy 06L-190 from the angles 06L-180.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06L-200, the washers 06L-210 and the angles 06L-180
from the aft side wall assembly 06L-010.
(j) Remove the screws 06L-270, the washers 06L-210 and the angle 06L-350
from the aft side wall assembly 06L-010.
(k) Remove the screws 06L-430 and the single door emergency unlocking device
assembly 06L-360 from the post assembly 06L-230.
(l) Disassemble the single door emergency unlocking device assembly 06L-360
as follows:
1 Remove the bolt 06L-420 and the emergency unlocking device strike
06L-380 from the emergency unlocking device housing 06L-370.
2 Remove the pin 06L-400, the snap catch 06L-410 and the emergency
unlocking device pivot 06L-390 from the emergency unlocking device
housing 06L-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06L-410 and the pin 06L-400.
(m) Remove the caps 06L-280, 06L-281, the screws 06L-270, 06L-290, the
washers 06L-210 and the post assembly 06L-230.
1 Remove the screws 06L-240 and the plates 06L-260 from the post
assembly 06L-230.
For Myanmar Airways (MMA) use only
(o) Remove the screws 06L-040, 06L-050 and the fittings 06L-020, 06L-030.
SUBTASK 25-41-58-010-019-B01
D2549020908200
(0) Removal of the Side Wall (06L-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3068
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06L-320 from the handle assembly 06L-300.
2 Remove the handle assembly 06L-300 from the aft side wall assembly
06L-010.
3 Remove the special screws 06L-310 and the special washers 06L-330
from the aft side wall assembly 06L-010.
(b) Remove the screws 06L-440, the washers 06L-210 and the support 06L-340
from the aft side wall assembly 06L-010.
(c) Remove the studs 06L-220 and the washers 06L-210 from the oxygen
container assy cover 06L-140.
(d) Remove the screws 06L-160, the nuts 06L-170 and the oxygen container assy
cover 06L-140 from the angle 06L-150.
(e) Remove the screws 06L-200, the washers 06L-210 and the angle 06L-150
from the aft side wall assembly 06L-010.
(f) Remove the ground cable from the oxygen container assy 06L-190.
For Myanmar Airways (MMA) use only
(g) Remove the screws 06L-200, the washers 06L-210 and the oxygen container
assy 06L-190 from the angles 06L-180.
(h) Remove the screws 06L-200, the washers 06L-210 and the angles 06L-180
from the aft side wall assembly 06L-010.
(j) Remove the screws 06L-270, the washers 06L-210 and the angle 06L-350
from the aft side wall assembly 06L-010.
(k) Remove the screws 06L-430 and the single door emergency unlocking device
assembly 06L-360 from the post assembly 06L-230.
(l) Disassemble the single door emergency unlocking device assembly 06L-360
as follows:
1 Remove the bolt 06L-420 and the emergency unlocking device strike
06L-380 from the emergency unlocking device housing 06L-370.
2 Remove the pin 06L-400, the snap catch 06L-410 and the emergency
unlocking device pivot 06L-390 from the emergency unlocking device
housing 06L-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06L-410 and the pin 06L-400.
(m) Remove the caps 06L-280, the screws 06L-270, 06L-290, the washers 06L-210
and the post assembly 06L-230.
1 Remove the screws 06L-240 and the plates 06L-260 from the post
assembly 06L-230.
(o) Remove the screws 06L-470 and the toilet seat-cover dispenser 06L-460 from
the aft side wall assembly 06L-010.
(p) Remove the screw 06L-431 and the coat hook 06L-450 from the aft side wall
assembly 06L-010.
(q) Remove the screws 06L-040, 06L-050 and the fittings 06L-020, 06L-030.
SUBTASK 25-41-58-010-019-C01
D2549020913200
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3069
For Myanmar Airways (MMA) use only
1 Remove the security pins 06L-320 from the handle assembly 06L-300.
2 Remove the handle assembly 06L-300 from the aft side wall assembly
06L-010.
3 Remove the special screws 06L-310 and the special washers 06L-330
from the aft side wall assembly 06L-010.
(b) Remove the screws 06L-440, the washers 06L-210 and the support 06L-340
from the aft side wall assembly 06L-010.
(c) Remove the studs 06L-220 and the washers 06L-210 from the oxygen
container assy cover 06L-140.
(d) Remove the screws 06L-160, the nuts 06L-170 and the oxygen container assy
cover 06L-140 from the angle 06L-150.
(e) Remove the screws 06L-200, the washers 06L-210 and the angle 06L-150
from the aft side wall assembly 06L-010.
(f) Remove the ground cable from the oxygen container assy 06L-190.
(g) Remove the screws 06L-200, the washers 06L-210 and the oxygen container
assy 06L-190 from the angles 06L-180.
(h) Remove the screws 06L-200, the washers 06L-210 and the angles 06L-180
from the aft side wall assembly 06L-010.
(j) Remove the screws 06L-270, the washers 06L-210 and the angle 06L-350
from the aft side wall assembly 06L-010.
(k) Remove the screws 06L-430 and the single door emergency unlocking device
assembly 06L-360 from the post assembly 06L-230.
(l) Disassemble the single door emergency unlocking device assembly 06L-360
as follows:
1 Remove the bolt 06L-420 and the emergency unlocking device strike
06L-380 from the emergency unlocking device housing 06L-370.
2 Remove the pin 06L-400, the snap catch 06L-410 and the emergency
unlocking device pivot 06L-390 from the emergency unlocking device
housing 06L-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06L-410 and the pin 06L-400.
(n) Remove the screws 06L-270, 06L-290, the washers 06L-210 and the post
assembly 06L-230.
1 Remove the screws 06L-240 and the plates 06L-260 from the post
assembly 06L-230.
(q) Remove the screws 06L-040, 06L-050 and the fittings 06L-020, 06L-030.
SUBTASK 25-41-58-010-019-D01
D2549026005200
(0) Removal of the Side Wall (06L-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
PART
NAME
Table 3070
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06L-320 from the handle assembly 06L-300.
2 Remove the handle assembly 06L-300 from the aft side wall assembly
06L-010.
3 Remove the special screws 06L-310 and the special washers 06L-330
from the aft side wall assembly 06L-010.
(b) Remove the screws 06L-440, the washers 06L-210 and the support 06L-340
from the aft side wall assembly 06L-010.
(c) Remove the studs 06L-220 and the washers 06L-210 from the oxygen
container assy cover 06L-140.
(d) Remove the screws 06L-160, the nuts 06L-170 and the oxygen container assy
cover 06L-140 from the angle 06L-150.
(e) Remove the screws 06L-200, the washers 06L-210 and the angle 06L-150
from the aft side wall assembly 06L-010.
(f) Remove the ground cable from the oxygen container assy 06L-190.
(g) Remove the screws 06L-200, the washers 06L-210 and the oxygen container
assy 06L-190 from the angles 06L-180.
(h) Remove the screws 06L-200, the washers 06L-210 and the angles 06L-180
from the aft side wall assembly 06L-010.
(j) Remove the screws 06L-270, the washers 06L-210 and the angle 06L-350
from the aft side wall assembly 06L-010.
(k) Remove the screws 06L-430 and the single door emergency unlocking device
assembly 06L-360 from the post assembly 06L-230.
For Myanmar Airways (MMA) use only
(l) Disassemble the single door emergency unlocking device assembly 06L-360
as follows:
1 Remove the bolt 06L-420 and the emergency unlocking device strike
06L-380 from the emergency unlocking device housing 06L-370.
2 Remove the pin 06L-400, the snap catch 06L-410 and the emergency
unlocking device pivot 06L-390 from the emergency unlocking device
housing 06L-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06L-410 and the pin 06L-400.
(n) Remove the screws 06L-270, 06L-290, the washers 06L-210 and the post
assembly 06L-230.
1 Remove the screws 06L-240 and the plates 06L-260 from the post
assembly 06L-230.
(q) Remove the screws 06L-470 and the toilet seat-cover dispenser 06L-460 from
the aft side wall assembly 06L-010.
(r) Remove the screws 06L-040, 06L-050 and the fittings 06L-020, 06L-030.
SUBTASK 25-41-58-010-019-E01
For Myanmar Airways (MMA) use only
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3071
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06L-320 from the handle assembly 06L-300.
2 Remove the handle assembly 06L-300 from the aft side wall assembly
06L-010.
3 Remove the special screws 06L-310 and the special washers 06L-330
from the aft side wall assembly 06L-010.
(c) Remove the screws 06L-440, the washers 06L-210 and the support 06L-340
from the aft side wall assembly 06L-010.
(d) Remove the studs 06L-220 and the washers 06L-210 from the oxygen
container assy cover 06L-140.
(e) Remove the screws 06L-160, the nuts 06L-170 and the oxygen container assy
cover 06L-140 from the angle 06L-150.
(f) Remove the screws 06L-200, 06L-205, the washers 06L-210, 06L-215 and the
angle 06L-150 from the aft side wall assembly 06L-010.
For Myanmar Airways (MMA) use only
(g) Remove the ground cable from the oxygen container assy 06L-190.
(h) Remove the screws 06L-200, 06L-205, the washers 06L-210 and the oxygen
container assy 06L-190 from the angles 06L-180.
(j) Remove the screws 06L-200, the washers 06L-210 and the angles 06L-180
from the aft side wall assembly 06L-010.
(k) Remove the screws 06L-270, the washers 06L-210 and the angle 06L-350
from the aft side wall assembly 06L-010.
(l) Remove the screws 06L-430 and the single door emergency unlocking device
assembly 06L-360 from the post assembly 06L-230.
(m) Disassemble the single door emergency unlocking device assembly 06L-360
as follows:
1 Remove the bolt 06L-420 and the emergency unlocking device strike
06L-380 from the emergency unlocking device housing 06L-370.
2 Remove the pin 06L-400, the snap catch 06L-410 and the emergency
unlocking device pivot 06L-390 from the emergency unlocking device
housing 06L-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06L-410 and the pin 06L-400.
(n) Remove the caps 06L-280, the screws 06L-270, 06L-290, the washers 06L-210
and the post assembly 06L-230..
1 Remove the screws 06L-240 and the plates 06L-260 from the post
assembly 06L-230.
(q) Remove the screws 06L-470 and the toilet seat-cover dispenser 06L-460 from
the aft side wall assembly 06L-010.
(r) Remove the screws 06L-040, 06L-050 and the fittings 06L-020, 06L-030.
SUBTASK 25-41-58-010-019-F01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3072
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06L-320 from the handle assembly 06L-300.
2 Remove the handle assembly 06L-300 from the aft side wall assembly
06L-010.
3 Remove the special screws 06L-310 and the special washers 06L-330
from the aft side wall assembly 06L-010.
(b) Remove the screws 06L-440, the washers 06L-210 and the support 06L-340
from the aft side wall assembly 06L-010.
(c) Remove the studs 06L-220 and the washers 06L-210 from the oxygen
container assy cover 06L-140.
For Myanmar Airways (MMA) use only
(d) Remove the screws 06L-160, the nuts 06L-170 and the oxygen container assy
cover 06L-140 from the angle 06L-150.
(e) Remove the screws 06L-200, the washers 06L-210 and the angle 06L-150
from the aft side wall assembly 06L-010.
(f) Remove the ground cable from the oxygen container assy 06L-190.
(g) Remove the screws 06L-200, the washers 06L-210 and the oxygen container
assy 06L-190 from the angles 06L-180.
(h) Remove the screws 06L-200, the washers 06L-210 and the angles 06L-180
from the aft side wall assembly 06L-010.
(j) Remove the screws 06L-270, the washers 06L-210 and the angle 06L-350
from the aft side wall assembly 06L-010.
(k) Remove the screws 06L-430 and the single door emergency unlocking device
assembly 06L-360 from the post assembly 06L-230.
(l) Disassemble the single door emergency unlocking device assembly 06L-360
as follows:
1 Remove the bolt 06L-420 and the emergency unlocking device strike
06L-380 from the emergency unlocking device housing 06L-370.
2 Remove the pin 06L-400, the snap catch 06L-410 and the emergency
unlocking device pivot 06L-390 from the emergency unlocking device
housing 06L-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
For Myanmar Airways (MMA) use only
(m) Remove the caps 06L-280, the screws 06L-270, 06L-290, the washers 06L-210
and the post assembly 06L-230.
1 Remove the screws 06L-240 and the plates 06L-260 from the post
assembly 06L-230.
(o) Remove the screws 06L-470 and the toilet seat-cover dispenser 06L-460 from
the aft side wall assembly 06L-010.
(p) Remove the screws 06L-040, 06L-050 and the fittings 06L-020, 06L-030.
SUBTASK 25-41-58-010-019-G01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3073
For Myanmar Airways (MMA) use only
1 Remove the security pins 06L-320 from the handle assembly 06L-300.
2 Remove the handle assembly 06L-300 from the aft side wall assembly
06L-010.
3 Remove the special screws 06L-310 and the special washers 06L-330
from the aft side wall assembly 06L-010.
(b) Remove the screws 06L-440, the washers 06L-210 and the support 06L-340
from the aft side wall assembly 06L-010.
(c) Remove the studs 06L-220 and the washers 06L-210 from the oxygen
container assy cover 06L-140.
(d) Remove the screws 06L-160, the nuts 06L-170 and the oxygen container assy
cover 06L-140 from the angle 06L-150.
(e) Remove the screws 06L-200, the washers 06L-210 and the angle 06L-150
from the aft side wall assembly 06L-010.
(f) Remove the ground cable from the oxygen container assy 06L-190.
(g) Remove the screws 06L-200, the washers 06L-210 and the oxygen container
assy 06L-190 from the angles 06L-180.
(h) Remove the screws 06L-200, the washers 06L-210 and the angles 06L-180
from the aft side wall assembly 06L-010.
(j) Remove the screws 06L-270, the washers 06L-210 and the angle 06L-350
from the aft side wall assembly 06L-010.
(k) Remove the screws 06L-430 and the single door emergency unlocking device
assembly 06L-360 from the post assembly 06L-230.
(l) Disassemble the single door emergency unlocking device assembly 06L-360
as follows:
1 Remove the bolt 06L-420 and the emergency unlocking device strike
06L-380 from the emergency unlocking device housing 06L-370.
2 Remove the pin 06L-400, the snap catch 06L-410 and the emergency
unlocking device pivot 06L-390 from the emergency unlocking device
housing 06L-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06L-410 and the pin 06L-400.
(m) Remove the caps 06L-280, the screws 06L-270, 06L-290, the washers 06L-210
and the post assembly 06L-230.
1 Remove the screws 06L-240 and the plates 06L-260 from the post
assembly 06L-230.
(o) Remove the screws 06L-040, 06L-050 and the fittings 06L-020, 06L-030.
TASK 25-41-58-000-804-N01
A. General
– Cleaning
For Myanmar Airways (MMA) use only
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-020-A01
D2549020907400 D2549020908600
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3074
For Myanmar Airways (MMA) use only
1 Remove the security pins 06M-160 from the handle assemblies 06M-140.
2 Remove the handle assemblies 06M-140 from the aft side wall assembly
06M-010.
3 Remove the special screws 06M-150 and the special washers 06M-170
from the aft side wall assembly 06M-010.
(b) Remove the studs 06M-260 and the washers 06M-250 from the oxygen
container assy cover 06M-180.
(c) Remove the screws 06M-200, the nuts 06M-210 and the oxygen container
assy cover 06M-180 from the angle 06M-190.
(d) Remove the screws 06M-240, the washers 06M-250 and the angle 06M-190
from the aft side wall assembly 06M-010.
(e) Remove the ground cable from the oxygen container assy 06M-230.
(f) Remove the screws 06M-240, the washers 06M-250 and the oxygen container
assy 06M-230 from the angles 06M-220.
(g) Remove the screws 06M-240, the washers 06M-250 and the angles 06M-220
from the aft side wall assembly 06M-010.
(h) Remove the screws 06M-310, the washers 06M-250 and the angle 06M-340
from the aft side wall assembly 06M-010.
(j) Remove the screws 06M-350 and the single door emergency unlocking device
assembly 06M-360 from the post assembly 06M-270.
(k) Disassemble the single door emergency unlocking device assembly 06M-360
as follows:
1 Remove the bolt 06M-420 and the emergency unlocking device strike
06M-380 from the emergency unlocking device housing 06M-370.
For Myanmar Airways (MMA) use only
2 Remove the pin 06M-400, the snap catch 06M-410 and the emergency
unlocking device pivot 06M-390 from the emergency unlocking device
housing 06M-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06M-410 and the pin 06M-400.
(l) Remove the caps 06M-320, the screws 06M-310, 06M-330, the washers
06M-250 and the post assembly 06M-270.
1 Remove the screws 06M-280 and the plates 06M-300 from the post
assembly 06M-270.
(n) Remove the screws 06M-440 and the toilet seat-cover dispenser 06M-430 from
the aft side wall assembly 06M-010.
(p) Remove the screw 06M-351 and the coat hook 06M-450 from the aft side
wall assembly 06M-010.
(q) Remove the screws 06M-040, 06M-050 and the fittings 06M-020, 06M-030.
SUBTASK 25-41-58-010-020-B01
D2549020907800 D2549020909400
(0) Removal of the Side Wall (06M-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3075
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06M-160 from the handle assemblies 06M-140.
2 Remove the handle assemblies 06M-140 from the aft side wall assembly
06M-010.
3 Remove the special screws 06M-150 and the special washers 06M-170
from the aft side wall assembly 06M-010.
(b) Remove the studs 06M-260 and the washers 06M-250 from the oxygen
container assy cover 06M-180.
(c) Remove the screws 06M-200, the nuts 06M-210 and the oxygen container
assy cover 06M-180 from the angle 06M-190.
(d) Remove the screws 06M-240, the washers 06M-250 and the angle 06M-190
from the aft side wall assembly 06M-010.
(e) Remove the ground cable from the oxygen container assy 06M-230.
(f) Remove the screws 06M-240, the washers 06M-250 and the oxygen container
assy 06M-230 from the angles 06M-220.
(g) Remove the screws 06M-240, the washers 06M-250 and the angles 06M-220
from the aft side wall assembly 06M-010.
(h) Remove the screws 06M-310, the washers 06M-250 and the angle 06M-340
from the aft side wall assembly 06M-010.
(j) Remove the screws 06M-350 and the single door emergency unlocking device
assembly 06M-360 from the post assembly 06M-270.
(k) Disassemble the single door emergency unlocking device assembly 06M-360
as follows:
1 Remove the bolt 06M-420 and the emergency unlocking device strike
06M-380 from the emergency unlocking device housing 06M-370.
2 Remove the pin 06M-400, the snap catch 06M-410 and the emergency
unlocking device pivot 06M-390 from the emergency unlocking device
housing 06M-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06M-410 and the pin 06M-400.
(l) Remove the caps 06M-320, the screws 06M-310, 06M-330, the washers
06M-250 and the post assembly 06M-270.
1 Remove the screws 06M-280 and the plates 06M-300 from the post
assembly 06M-270.
(n) Remove the screws 06M-440 and the toilet seat-cover dispenser 06M-430 from
the aft side wall assembly 06M-010.
(p) Remove the screws 06M-040, 06M-050 and the fittings 06M-020, 06M-030.
SUBTASK 25-41-58-010-020-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
For Myanmar Airways (MMA) use only
Table 3076
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06M-160 from the handle assemblies 06M-140.
2 Remove the handle assemblies 06M-140 from the aft side wall assembly
06M-010.
3 Remove the special screws 06M-150 and the special washers 06M-170
from the aft side wall assembly 06M-010.
(b) Remove the studs 06M-260 and the washers 06M-250 from the oxygen
container assy cover 06M-180.
(c) Remove the screws 06M-200, the nuts 06M-210 and the oxygen container
assy cover 06M-180 from the angle 06M-190.
(d) Remove the screws 06M-240, the washers 06M-250 and the angle 06M-190
from the aft side wall assembly 06M-010.
(e) Remove the ground cable from the oxygen container assy 06M-230.
(f) Remove the screws 06M-240, 06M-245, the washers 06M-250 and the oxygen
container assy 06M-230 from the angles 06M-220.
(g) Remove the screws 06M-240, the washers 06M-250 and the angles 06M-220
from the aft side wall assembly 06M-010.
(h) Remove the screws 06M-310, the washers 06M-250 and the angle 06M-340
from the aft side wall assembly 06M-010.
(j) Remove the screws 06M-350 and the single door emergency unlocking device
assembly 06M-360 from the post assembly 06M-270.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06M-360
as follows:
1 Remove the bolt 06M-420 and the emergency unlocking device strike
06M-380 from the emergency unlocking device housing 06M-370.
2 Remove the pin 06M-400, the snap catch 06M-410 and the emergency
unlocking device pivot 06M-390 from the emergency unlocking device
housing 06M-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06M-410 and the pin 06M-400.
(l) Remove the caps 06M-320, the screws 06M-310, 06M-330, the washers
06M-250 and the post assembly 06M-270.
1 Remove the screws 06M-280 and the plates 06M-300 from the post
assembly 06M-270.
(n) Remove the screws 06M-040, 06M-050 and the fittings 06M-020, 06M-030.
SUBTASK 25-41-58-010-020-D01
D2549010412800
(0) Removal of the Side Wall (06M-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3077
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06M-160 from the handle assemblies 06M-140.
2 Remove the handle assemblies 06M-140 from the aft side wall assembly
06M-010.
3 Remove the special screws 06M-150 and the special washers 06M-170
from the aft side wall assembly 06M-010.
(b) Remove the studs 06M-260 and the washers 06M-250 from the oxygen
container assy cover 06M-180.
(c) Remove the screws 06M-200, the nuts 06M-210 and the oxygen container
assy cover 06M-180 from the angle 06M-190.
(d) Remove the screws 06M-240, the washers 06M-250 and the angle 06M-190
from the aft side wall assembly 06M-010.
(e) Remove the ground cable from the oxygen container assy 06M-230.
(f) Remove the screws 06M-240, the washers 06M-250 and the oxygen container
assy 06M-230 from the angles 06M-220.
(g) Remove the screws 06M-240, the washers 06M-250 and the angles 06M-220
from the aft side wall assembly 06M-010.
(h) Remove the screws 06M-310, the washers 06M-250 and the angle 06M-340
from the aft side wall assembly 06M-010.
(j) Remove the screws 06M-350 and the single door emergency unlocking device
assembly 06M-360 from the post assembly 06M-270.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06M-360
as follows:
1 Remove the bolt 06M-420 and the emergency unlocking device strike
06M-380 from the emergency unlocking device housing 06M-370.
2 Remove the pin 06M-400, the snap catch 06M-410 and the emergency
unlocking device pivot 06M-390 from the emergency unlocking device
housing 06M-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06M-410 and the pin 06M-400.
(l) Remove the caps 06M-320, the screws 06M-310, 06M-330, the washers
06M-250 and the post assembly 06M-270.
1 Remove the screws 06M-280 and the plates 06M-300 from the post
assembly 06M-270.
(n) Remove the screws 06M-040, 06M-050 and the fittings 06M-020, 06M-030.
SUBTASK 25-41-58-010-020-E01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3078
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06M-160 from the handle assemblies 06M-140.
2 Remove the handle assemblies 06M-140 from the aft side wall assembly
06M-010.
3 Remove the special screws 06M-150 and the special washers 06M-170
from the aft side wall assembly 06M-010.
(b) Remove the studs 06M-260 and the washers 06M-250 from the oxygen
container assy cover 06M-180.
(c) Remove the screws 06M-200, the nuts 06M-210 and the oxygen container
assy cover 06M-180 from the angle 06M-190.
(d) Remove the screws 06M-240, the washers 06M-250 and the angle 06M-190
from the aft side wall assembly 06M-010.
(e) Remove the ground cable from the oxygen container assy 06M-230.
(f) Remove the screws 06M-240, 06M-245, the washers 06M-250 and the oxygen
container assy 06M-230 from the angles 06M-220.
(g) Remove the screws 06M-240, the washers 06M-250 and the angles 06M-220
from the aft side wall assembly 06M-010.
(h) Remove the screws 06M-310, the washers 06M-250 and the angle 06M-340
from the aft side wall assembly 06M-010.
(j) Remove the screws 06M-350 and the single door emergency unlocking device
assembly 06M-360 from the post assembly 06M-270.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06M-360
as follows:
1 Remove the bolt 06M-420 and the emergency unlocking device strike
06M-380 from the emergency unlocking device housing 06M-370.
2 Remove the pin 06M-400, the snap catch 06M-410 and the emergency
unlocking device pivot 06M-390 from the emergency unlocking device
housing 06M-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06M-410 and the pin 06M-400.
(l) Remove the caps 06M-320, the screws 06M-310, 06M-330, the washers
06M-250 and the post assembly 06M-270.
1 Remove the screws 06M-280 and the plates 06M-300 from the post
assembly 06M-270.
(n) Remove the screws 06M-040, 06M-050 and the fittings 06M-020, 06M-030.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-804-P01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-021-A01
D2549040505800 R225401882-006
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3079
For Myanmar Airways (MMA) use only
1 Remove the security pins 06N-160 from the handle assemblies 06N-140.
2 Remove the handle assemblies 06N-140 from the aft side wall assembly
06N-010.
3 Remove the special screws 06N-150 and the special washers 06N-170
from the aft side wall assembly 06N-010.
(b) Remove the studs 06N-260 and the washers 06N-250 from the oxygen
container assy cover 06N-180.
(c) Remove the screws 06N-200, the nuts 06N-210 and the oxygen container assy
cover 06N-180 from the angle 06N-190.
(d) Remove the screws 06N-240, the washers 06N-250 and the angle 06N-190
from the aft side wall assembly 06N-010.
(e) Remove the ground cable from the oxygen container assy 06N-230.
(f) Remove the screws 06N-240, 06N-245, the washers 06N-250 and the oxygen
container assy 06N-230 from the angles 06N-220.
(g) Remove the screws 06N-240, the washers 06N-250 and the angles 06N-220
from the aft side wall assembly 06N-010.
(h) Remove the screws 06N-310, the washers 06N-250 and the angle 06N-340
from the aft side wall assembly 06N-010.
(j) Remove the screws 06N-350 and the single door emergency unlocking device
assembly 06N-360 from the post assembly 06N-270.
(k) Disassemble the single door emergency unlocking device assembly 06N-360
as follows:
1 Remove the bolt 06N-420 and the emergency unlocking device strike
06N-380 from the emergency unlocking device housing 06N-370.
For Myanmar Airways (MMA) use only
2 Remove the pin 06N-400, the snap catch 06N-410 and the emergency
unlocking device pivot 06N-390 from the emergency unlocking device
housing 06N-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06N-410 and the pin 06N-400.
(m) Remove the screws 06N-310, 06N-330, the washers 06N-250 and the post
assembly 06N-270.
1 Remove the screws 06N-280 and the plates 06N-300 from the post
assembly 06N-270.
(o) Remove the screws 06N-440 and the toilet seat-cover dispenser 06N-430 from
the aft side wall assembly 06N-010.
(p) Remove the screw 06N-351 and the coat hook 06N-450 from the aft side wall
assembly 06N-010.
(q) Remove the screws 06N-040, 06N-050 and the fittings 06N-020, 06N-030.
SUBTASK 25-41-58-010-021-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
For Myanmar Airways (MMA) use only
Table 3080
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06N-160 from the handle assemblies 06N-140.
2 Remove the handle assemblies 06N-140 from the aft side wall assembly
06N-010.
3 Remove the special screws 06N-150 and the special washers 06N-170
from the aft side wall assembly 06N-010.
(b) Remove the studs 06N-260 and the washers 06N-250 from the oxygen
container assy cover 06N-180.
(c) Remove the screws 06N-200, the nuts 06N-210 and the oxygen container assy
cover 06N-180 from the angle 06N-190.
(d) Remove the screws 06N-240, the washers 06N-250 and the angle 06N-190
from the aft side wall assembly 06N-010.
(e) Remove the ground cable from the oxygen container assy 06N-230.
(f) Remove the screws 06N-240, 06N-245, the washers 06N-250 and the oxygen
container assy 06N-230 from the angles 06N-220.
(g) Remove the screws 06N-240, the washers 06N-250 and the angles 06N-220
from the aft side wall assembly 06N-010.
(h) Remove the screws 06N-310, the washers 06N-250 and the angle 06N-340
from the aft side wall assembly 06N-010.
(j) Remove the screws 06N-350 and the single door emergency unlocking device
assembly 06N-360 from the post assembly 06N-270.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06N-360
as follows:
1 Remove the bolt 06N-420 and the emergency unlocking device strike
06N-380 from the emergency unlocking device housing 06N-370.
2 Remove the pin 06N-400, the snap catch 06N-410 and the emergency
unlocking device pivot 06N-390 from the emergency unlocking device
housing 06N-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06N-410 and the pin 06N-400.
(l) Remove the caps 06N-320, the screws 06N-310, 06N-330, the washers
06N-250 and the post assembly 06N-270.
1 Remove the screws 06N-280 and the plates 06N-300 from the post
assembly 06N-270.
(n) Remove the screws 06N-440 and the toilet seat-cover dispenser 06N-430 from
the aft side wall assembly 06N-010.
(p) Remove the screw 06N-351 and the coat hook 06N-450 from the aft side wall
assembly 06N-010.
(q) Remove the screws 06N-040, 06N-050 and the fittings 06N-020, 06N-030.
SUBTASK 25-41-58-010-021-C01
D2549030807400
For Myanmar Airways (MMA) use only
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3081
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06N-160 from the handle assemblies 06N-140.
2 Remove the handle assemblies 06N-140 from the aft side wall assembly
06N-010.
3 Remove the special screws 06N-150 and the special washers 06N-170
from the aft side wall assembly 06N-010.
(b) Remove the studs 06N-260 and the washers 06N-250 from the oxygen
container assy cover 06N-180.
(c) Remove the screws 06N-200, the nuts 06N-210 and the oxygen container assy
cover 06N-180 from the angle 06N-190.
(d) Remove the screws 06N-240, the washers 06N-250 and the angle 06N-190
from the aft side wall assembly 06N-010.
(e) Remove the ground cable from the oxygen container assy 06N-230.
(f) Remove the screws 06N-240, the washers 06N-250 and the oxygen container
assy 06N-230 from the angles 06N-220.
(g) Remove the screws 06N-240, the washers 06N-250 and the angles 06N-220
from the aft side wall assembly 06N-010.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06N-310, the washers 06N-250 and the angle 06N-340
from the aft side wall assembly 06N-010.
(j) Remove the screws 06N-350 and the single door emergency unlocking device
assembly 06N-360 from the post assembly 06N-270.
(k) Disassemble the single door emergency unlocking device assembly 06N-360
as follows:
1 Remove the bolt 06N-420 and the emergency unlocking device strike
06N-380 from the emergency unlocking device housing 06N-370.
2 Remove the pin 06N-400, the snap catch 06N-410 and the emergency
unlocking device pivot 06N-390 from the emergency unlocking device
housing 06N-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06N-410 and the pin 06N-400.
(l) Remove the caps 06N-320, the screws 06N-310, 06N-330, the washers
06N-250 and the post assembly 06N-270.
1 Remove the screws 06N-280 and the plates 06N-300 from the post
assembly 06N-270.
(n) Remove the screws 06N-440 and the toilet seat-cover dispenser 06N-430 from
the aft side wall assembly 06N-010.
For Myanmar Airways (MMA) use only
(p) Remove the screw 06N-351 and the coat hook 06N-450 from the aft side wall
assembly 06N-010.
(q) Remove the screws 06N-040, 06N-050 and the fittings 06N-020, 06N-030.
SUBTASK 25-41-58-010-021-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3082
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06N-160 from the handle assemblies 06N-140.
2 Remove the handle assemblies 06N-140 from the aft side wall assembly
06N-010.
3 Remove the special screws 06N-150 and the special washers 06N-170
from the aft side wall assembly 06N-010.
(b) Remove the studs 06N-260 and the washers 06N-250 from the oxygen
container assy cover 06N-180.
(c) Remove the screws 06N-200, the nuts 06N-210 and the oxygen container assy
cover 06N-180 from the angle 06N-190.
(d) Remove the screws 06N-240, the washers 06N-250 and the angle 06N-190
from the aft side wall assembly 06N-010.
For Myanmar Airways (MMA) use only
(e) Remove the ground cable from the oxygen container assy 06N-230.
(f) Remove the screws 06N-240, the washers 06N-250 and the oxygen container
assy 06N-230 from the angles 06N-220.
(g) Remove the screws 06N-240, the washers 06N-250 and the angles 06N-220
from the aft side wall assembly 06N-010.
(h) Remove the screws 06N-310, the washers 06N-250 and the angle 06N-340
from the aft side wall assembly 06N-010.
(j) Remove the screws 06N-350 and the single door emergency unlocking device
assembly 06N-360 from the post assembly 06N-270.
(k) Disassemble the single door emergency unlocking device assembly 06N-360
as follows:
1 Remove the bolt 06N-420 and the emergency unlocking device strike
06N-380 from the emergency unlocking device housing 06N-370.
2 Remove the pin 06N-400, the snap catch 06N-410 and the emergency
unlocking device pivot 06N-390 from the emergency unlocking device
housing 06N-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06N-410 and the pin 06N-400.
(l) Remove the caps 06N-320, the screws 06N-310, 06N-330, the washers
06N-250 and the post assembly 06N-270.
1 Remove the screws 06N-280 and the plates 06N-300 from the post
assembly 06N-270.
(n) Remove the screws 06N-440 and the toilet seat-cover dispenser 06N-430 from
the aft side wall assembly 06N-010.
(p) Remove the screws 06N-040, 06N-050 and the fittings 06N-020, 06N-030.
SUBTASK 25-41-58-010-021-E01
D2549030808400
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3083
For Myanmar Airways (MMA) use only
1 Remove the security pins 06N-160 from the handle assemblies 06N-140.
2 Remove the handle assemblies 06N-140 from the aft side wall assembly
06N-010.
3 Remove the special screws 06N-150 and the special washers 06N-170
from the aft side wall assembly 06N-010.
(b) Remove the studs 06N-260 and the washers 06N-250 from the oxygen
container assy cover 06N-180.
(c) Remove the screws 06N-200, the nuts 06N-210 and the oxygen container assy
cover 06N-180 from the angle 06N-190.
(d) Remove the screws 06N-240, the washers 06N-250 and the angle 06N-190
from the aft side wall assembly 06N-010.
(e) Remove the ground cable from the oxygen container assy 06N-230.
(f) Remove the screws 06N-240, the washers 06N-250 and the oxygen container
assy 06N-230 from the angles 06N-220.
(g) Remove the screws 06N-240, the washers 06N-250 and the angles 06N-220
from the aft side wall assembly 06N-010.
(h) Remove the screws 06N-310, the washers 06N-250 and the angle 06N-340
from the aft side wall assembly 06N-010.
(j) Remove the screws 06N-350 and the single door emergency unlocking device
assembly 06N-360 from the post assembly 06N-270.
(k) Disassemble the single door emergency unlocking device assembly 06N-360
as follows:
1 Remove the bolt 06N-420 and the emergency unlocking device strike
06N-380 from the emergency unlocking device housing 06N-370.
For Myanmar Airways (MMA) use only
2 Remove the pin 06N-400, the snap catch 06N-410 and the emergency
unlocking device pivot 06N-390 from the emergency unlocking device
housing 06N-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06N-410 and the pin 06N-400.
(l) Remove the caps 06N-320, the screws 06N-310, 06N-330, the washers
06N-250 and the post assembly 06N-270.
1 Remove the screws 06N-280 and the plates 06N-300 from the post
assembly 06N-270.
(n) Remove the screws 06N-440 and the toilet seat-cover dispenser 06N-430 from
the aft side wall assembly 06N-010.
(p) Remove the screws 06N-040, 06N-050 and the fittings 06N-020, 06N-030.
SUBTASK 25-41-58-010-021-F01
D2549020908000 D2549020911200
(0) Removal of the Side Wall (06N-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Assembly 350-802-A01
Table 3084
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06N-160 from the handle assemblies 06N-140.
2 Remove the handle assemblies 06N-140 from the aft side wall assembly
06N-010.
3 Remove the special screws 06N-150 and the special washers 06N-170
from the aft side wall assembly 06N-010.
(b) Remove the studs 06N-260 and the washers 06N-250 from the oxygen
container assy cover 06N-180.
(c) Remove the screws 06N-200, the nuts 06N-210 and the oxygen container assy
cover 06N-180 from the angle 06N-190.
(d) Remove the screws 06N-240, the washers 06N-250 and the angle 06N-190
from the aft side wall assembly 06N-010.
(e) Remove the ground cable from the oxygen container assy 06N-230.
(f) Remove the screws 06N-240, the washers 06N-250 and the oxygen container
assy 06N-230 from the angles 06N-220.
(g) Remove the screws 06N-240, the washers 06N-250 and the angles 06N-220
from the aft side wall assembly 06N-010.
(h) Remove the screws 06N-310, the washers 06N-250 and the angle 06N-340
from the aft side wall assembly 06N-010.
(j) Remove the screws 06N-350 and the single door emergency unlocking device
assembly 06N-360 from the post assembly 06N-270.
(k) Disassemble the single door emergency unlocking device assembly 06N-360
as follows:
1 Remove the bolt 06N-420 and the emergency unlocking device strike
06N-380 from the emergency unlocking device housing 06N-370.
2 Remove the pin 06N-400, the snap catch 06N-410 and the emergency
unlocking device pivot 06N-390 from the emergency unlocking device
housing 06N-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06N-410 and the pin 06N-400.
(l) Remove the caps 06N-320, the screws 06N-310, 06N-330, the washers
06N-250 and the post assembly 06N-270.
1 Remove the screws 06N-280 and the plates 06N-300 from the post
assembly 06N-270.
(n) Remove the screws 06N-440 and the toilet seat-cover dispenser 06N-430 from
the aft side wall assembly 06N-010.
(p) Remove the screws 06N-040, 06N-050 and the fittings 06N-020, 06N-030.
SUBTASK 25-41-58-010-021-G01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3085
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06N-160 from the handle assemblies 06N-140.
2 Remove the handle assemblies 06N-140 from the aft side wall assembly
06N-010.
3 Remove the special screws 06N-150 and the special washers 06N-170
from the aft side wall assembly 06N-010.
(b) Remove the studs 06N-260 and the washers 06N-250 from the oxygen
container assy cover 06N-180.
(c) Remove the screws 06N-200, the nuts 06N-210 and the oxygen container assy
cover 06N-180 from the angle 06N-190.
(d) Remove the screws 06N-240, the washers 06N-250 and the angle 06N-190
from the aft side wall assembly 06N-010.
(e) Remove the ground cable from the oxygen container assy 06N-230.
(f) Remove the screws 06N-240, 06N-245, the washers 06N-250, 06N-255 and
the oxygen container assy 06N-230 from the angles 06N-220.
(g) Remove the screws 06N-240, the washers 06N-250 and the angles 06N-220
from the aft side wall assembly 06N-010.
(h) Remove the screws 06N-310, the washers 06N-250 and the angle 06N-340
from the aft side wall assembly 06N-010.
(j) Remove the screws 06N-350 and the single door emergency unlocking device
assembly 06N-360 from the post assembly 06N-270.
(k) Disassemble the single door emergency unlocking device assembly 06N-360
as follows:
1 Remove the bolt 06N-420 and the emergency unlocking device strike
06N-380 from the emergency unlocking device housing 06N-370.
2 Remove the pin 06N-400, the snap catch 06N-410 and the emergency
unlocking device pivot 06N-390 from the emergency unlocking device
housing 06N-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06N-410 and the pin 06N-400.
(l) Remove the caps 06N-320, the screws 06N-310, 06N-330, the washers
06N-250 and the post assembly 06N-270.
1 Remove the screws 06N-280 and the plates 06N-300 from the post
assembly 06N-270.
(n) Remove the screws 06N-440 and the toilet seat-cover dispenser 06N-430 from
the aft side wall assembly 06N-010.
(p) Remove the screws 06N-040, 06N-050 and the fittings 06N-020, 06N-030.
SUBTASK 25-41-58-010-021-H01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
PART
NAME
Table 3086
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06N-160 from the handle assemblies 06N-140.
2 Remove the handle assemblies 06N-140 from the aft side wall assembly
06N-010.
3 Remove the special screws 06N-150 and the special washers 06N-170
from the aft side wall assembly 06N-010.
(b) Remove the studs 06N-260 and the washers 06N-250 from the oxygen
container assy cover 06N-180.
(c) Remove the screws 06N-200, the nuts 06N-210 and the oxygen container assy
cover 06N-180 from the angle 06N-190.
(d) Remove the screws 06N-240, the washers 06N-250 and the angle 06N-190
from the aft side wall assembly 06N-010.
(e) Remove the ground cable from the oxygen container assy 06N-230.
(f) Remove the screws 06N-240, the washers 06N-250 and the oxygen container
assy 06N-230 from the angles 06N-220.
(g) Remove the screws 06N-240, the washers 06N-250 and the angles 06N-220
from the aft side wall assembly 06N-010.
(h) Remove the screws 06N-310, the washers 06N-250 and the angle 06N-340
from the aft side wall assembly 06N-010.
(j) Remove the screws 06N-350 and the single door emergency unlocking device
assembly 06N-360 from the post assembly 06N-270.
(k) Disassemble the single door emergency unlocking device assembly 06N-360
as follows:
For Myanmar Airways (MMA) use only
1 Remove the bolt 06N-420 and the emergency unlocking device strike
06N-380 from the emergency unlocking device housing 06N-370.
2 Remove the pin 06N-400, the snap catch 06N-410 and the emergency
unlocking device pivot 06N-390 from the emergency unlocking device
housing 06N-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06N-410 and the pin 06N-400.
(l) Remove the caps 06N-320, the screws 06N-310, 06N-330, the washers
06N-250 and the post assembly 06N-270.
1 Remove the screws 06N-280 and the plates 06N-300 from the post
assembly 06N-270.
(n) Remove the screws 06N-040, 06N-050 and the fittings 06N-020, 06N-030.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-804-Q01
A. General
– Cleaning
– Visual Inspection
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-022-A01
D2549020905600 D2549030809600
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3087
For Myanmar Airways (MMA) use only
1 Remove the security pins 06P-160 from the handle assemblies 06P-140.
2 Remove the handle assemblies 06P-140 from the aft side wall assembly
06P-010.
3 Remove the special screws 06P-150 and the special washers 06P-170
from the aft side wall assembly 06P-010.
(b) Remove the studs 06P-260 and the washers 06P-250 from the oxygen
container assy cover 06P-180.
(c) Remove the screws 06P-200, the nuts 06P-210 and the oxygen container assy
cover 06P-180 from the angle 06P-190.
(d) Remove the screws 06P-240, the washers 06P-250 and the angle 06P-190
from the aft side wall assembly 06P-010.
(e) Remove the ground cable from the oxygen container assy 06P-230.
(f) Remove the screws 06P-240, the washers 06P-250 and the oxygen container
assy 06P-230 from the angles 06P-220.
(g) Remove the screws 06P-240, the washers 06P-250 and the angles 06P-220
from the aft side wall assembly 06P-010.
(h) Remove the screws 06P-310, the washers 06P-250 and the angle 06P-340
from the aft side wall assembly 06P-010.
(j) Remove the screws 06P-350 and the single door emergency unlocking device
assembly 06P-360 from the post assembly 06P-270.
(k) Disassemble the single door emergency unlocking device assembly 06P-360
as follows:
1 Remove the bolt 06P-420 and the emergency unlocking device strike
06P-380 from the emergency unlocking device housing 06P-370.
For Myanmar Airways (MMA) use only
2 Remove the pin 06P-400, the snap catch 06P-410 and the emergency
unlocking device pivot 06P-390 from the emergency unlocking device
housing 06P-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06P-410 and the pin 06P-400.
(l) Remove the caps 06P-320, the screws 06P-310, 06P-330, the washers
06P-250 and the post assembly 06P-270.
1 Remove the screws 06P-280 and the plates 06P-300 from the post
assembly 06P-270.
(n) Remove the screws 06P-440 and the toilet seat-cover dispenser 06P-430 from
the aft side wall assembly 06P-010.
(p) Remove the screw 06P-351 and the coat hook 06P-450 from the aft side wall
assembly 06P-010.
(q) Remove the screws 06P-040, 06P-050 and the fittings 06P-020, 06P-030.
SUBTASK 25-41-58-010-022-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3088
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06P-160 from the handle assemblies 06P-140.
2 Remove the handle assemblies 06P-140 from the aft side wall assembly
06P-010.
3 Remove the special screws 06P-150 and the special washers 06P-170
from the aft side wall assembly 06P-010.
(b) Remove the studs 06P-260 and the washers 06P-250 from the oxygen
container assy cover 06P-180.
(c) Remove the screws 06P-200, the nuts 06P-210 and the oxygen container assy
cover 06P-180 from the angle 06P-190.
(d) Remove the screws 06P-240, the washers 06P-250 and the angle 06P-190
from the aft side wall assembly 06P-010.
(e) Remove the ground cable from the oxygen container assy 06P-230.
(f) Remove the screws 06P-240, the washers 06P-250 and the oxygen container
assy 06P-230 from the angles 06P-220.
(g) Remove the screws 06P-240, the washers 06P-250 and the angles 06P-220
from the aft side wall assembly 06P-010.
(h) Remove the screws 06P-310, the washers 06P-250 and the angle 06P-340
from the aft side wall assembly 06P-010.
(j) Remove the screws 06P-350 and the single door emergency unlocking device
assembly 06P-360 from the post assembly 06P-270.
(k) Disassemble the single door emergency unlocking device assembly 06P-360
as follows:
1 Remove the bolt 06P-420 and the emergency unlocking device strike
06P-380 from the emergency unlocking device housing 06P-370.
2 Remove the pin 06P-400, the snap catch 06P-410 and the emergency
unlocking device pivot 06P-390 from the emergency unlocking device
housing 06P-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06P-410 and the pin 06P-400.
(l) Remove the caps 06P-320, the screws 06P-310, 06P-330, the washers
06P-250 and the post assembly 06P-270.
1 Remove the screws 06P-280 and the plates 06P-300 from the post
assembly 06P-270.
(n) Remove the screws 06P-440 and the toilet seat-cover dispenser 06P-430 from
the aft side wall assembly 06P-010.
(p) Remove the screw 06P-351 and the coat hook 06P-450 from the aft side wall
assembly 06P-010.
(q) Remove the screws 06P-040, 06P-050 and the fittings 06P-020, 06P-030.
SUBTASK 25-41-58-010-022-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
For Myanmar Airways (MMA) use only
Table 3089
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06P-160 from the handle assemblies 06P-140.
2 Remove the handle assemblies 06P-140 from the aft side wall assembly
06P-010.
3 Remove the special screws 06P-150 and the special washers 06P-170
from the aft side wall assembly 06P-010.
(b) Remove the studs 06P-260 and the washers 06P-250 from the oxygen
container assy cover 06P-180.
(c) Remove the screws 06P-200, the nuts 06P-210 and the oxygen container assy
cover 06P-180 from the angle 06P-190.
(d) Remove the screws 06P-240, the washers 06P-250 and the angle 06P-190
from the aft side wall assembly 06P-010.
(e) Remove the ground cable from the oxygen container assy 06P-230.
(f) Remove the screws 06P-240, 06P-245, the washers 06P-250 and the oxygen
container assy 06P-230 from the angles 06P-220.
(g) Remove the screws 06P-240, the washers 06P-250 and the angles 06P-220
from the aft side wall assembly 06P-010.
(h) Remove the screws 06P-310, the washers 06P-250 and the angle 06P-340
from the aft side wall assembly 06P-010.
(j) Remove the screws 06P-350 and the single door emergency unlocking device
assembly 06P-360 from the post assembly 06P-270.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06P-360
as follows:
1 Remove the bolt 06P-420 and the emergency unlocking device strike
06P-380 from the emergency unlocking device housing 06P-370.
2 Remove the pin 06P-400, the snap catch 06P-410 and the emergency
unlocking device pivot 06P-390 from the emergency unlocking device
housing 06P-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06P-410 and the pin 06P-400.
(m) Remove the screws 06P-310, 06P-330, the washers 06P-250 and the post
assembly 06P-270.
1 Remove the screws 06P-280 and the plates 06P-300 from the post
assembly 06P-270.
(o) Remove the screw 06P-351 and the coat hook 06P-450 from the aft side wall
assembly 06P-010.
(p) Remove the screws 06P-040, 06P-050 and the fittings 06P-020, 06P-030.
SUBTASK 25-41-58-010-022-D01
For Myanmar Airways (MMA) use only
D2549030809200
(0) Removal of the Side Wall (06P-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3090
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06P-160 from the handle assemblies 06P-140.
2 Remove the handle assemblies 06P-140 from the aft side wall assembly
06P-010.
3 Remove the special screws 06P-150 and the special washers 06P-170
from the aft side wall assembly 06P-010.
(b) Remove the studs 06P-260 and the washers 06P-250 from the oxygen
container assy cover 06P-180.
(c) Remove the screws 06P-200, the nuts 06P-210 and the oxygen container assy
cover 06P-180 from the angle 06P-190.
(d) Remove the screws 06P-240, the washers 06P-250 and the angle 06P-190
from the aft side wall assembly 06P-010.
(e) Remove the ground cable from the oxygen container assy 06P-230.
(f) Remove the screws 06P-240, the washers 06P-250 and the oxygen container
assy 06P-230 from the angles 06P-220.
For Myanmar Airways (MMA) use only
(g) Remove the screws 06P-240, the washers 06P-250 and the angles 06P-220
from the aft side wall assembly 06P-010.
(h) Remove the screws 06P-310, the washers 06P-250 and the angle 06P-340
from the aft side wall assembly 06P-010.
(j) Remove the screws 06P-350 and the single door emergency unlocking device
assembly 06P-360 from the post assembly 06P-270.
(k) Disassemble the single door emergency unlocking device assembly 06P-360
as follows:
1 Remove the bolt 06P-420 and the emergency unlocking device strike
06P-380 from the emergency unlocking device housing 06P-370.
2 Remove the pin 06P-400, the snap catch 06P-410 and the emergency
unlocking device pivot 06P-390 from the emergency unlocking device
housing 06P-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06P-410 and the pin 06P-400.
(m) Remove the screws 06P-310, 06P-330, the washers 06P-250 and the post
assembly 06P-270.
1 Remove the screws 06P-280 and the plates 06P-300 from the post
assembly 06P-270.
(o) Remove the screws 06P-440 and the toilet seat-cover dispenser 06P-430 from
the aft side wall assembly 06P-010.
(p) Remove the screw 06P-351 and the coat hook 06P-450 from the aft side wall
assembly 06P-010.
(q) Remove the screws 06P-040, 06P-050 and the fittings 06P-020, 06P-030.
SUBTASK 25-41-58-010-022-E01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3091
For Myanmar Airways (MMA) use only
1 Remove the security pins 06P-160 from the handle assemblies 06P-140.
2 Remove the handle assemblies 06P-140 from the aft side wall assembly
06P-010.
3 Remove the special screws 06P-150 and the special washers 06P-170
from the aft side wall assembly 06P-010.
(b) Remove the studs 06P-260 and the washers 06P-250 from the oxygen
container assy cover 06P-180.
(c) Remove the screws 06P-200, the nuts 06P-210 and the oxygen container assy
cover 06P-180 from the angle 06P-190.
(d) Remove the screws 06P-240, the washers 06P-250 and the angle 06P-190
from the aft side wall assembly 06P-010.
(e) Remove the ground cable from the oxygen container assy 06P-230.
(f) Remove the screws 06P-240, the washers 06P-250 and the oxygen container
assy 06P-230 from the angles 06P-220.
(g) Remove the screws 06P-240, the washers 06P-250 and the angles 06P-220
from the aft side wall assembly 06P-010.
(h) Remove the screws 06P-310, the washers 06P-250 and the angle 06P-340
from the aft side wall assembly 06P-010.
(j) Remove the screws 06P-350 and the single door emergency unlocking device
assembly 06P-360 from the post assembly 06P-270.
(k) Disassemble the single door emergency unlocking device assembly 06P-360
as follows:
1 Remove the bolt 06P-420 and the emergency unlocking device strike
06P-380 from the emergency unlocking device housing 06P-370.
For Myanmar Airways (MMA) use only
2 Remove the pin 06P-400, the snap catch 06P-410 and the emergency
unlocking device pivot 06P-390 from the emergency unlocking device
housing 06P-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06P-410 and the pin 06P-400.
(m) Remove the screws 06P-310, 06P-330, the washers 06P-250 and the post
assembly 06P-270.
1 Remove the screws 06P-280 and the plates 06P-300 from the post
assembly 06P-270.
(o) Remove the screws 06P-440 and the toilet seat-cover dispenser 06P-430 from
the aft side wall assembly 06P-010.
(p) Remove the screws 06P-040, 06P-050 and the fittings 06P-020, 06P-030.
SUBTASK 25-41-58-010-022-F01
D2549020911000 D2549020913800
(0) Removal of the Side Wall (06P-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
PART
NAME
Table 3092
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06P-160 from the handle assemblies 06P-140.
2 Remove the handle assemblies 06P-140 from the aft side wall assembly
06P-010.
3 Remove the special screws 06P-150 and the special washers 06P-170
from the aft side wall assembly 06P-010.
(b) Remove the studs 06P-260 and the washers 06P-250 from the oxygen
container assy cover 06P-180.
(c) Remove the screws 06P-200, the nuts 06P-210 and the oxygen container assy
cover 06P-180 from the angle 06P-190.
(d) Remove the screws 06P-240, the washers 06P-250 and the angle 06P-190
from the aft side wall assembly 06P-010.
(e) Remove the ground cable from the oxygen container assy 06P-230.
(f) Remove the screws 06P-240, the washers 06P-250 and the oxygen container
assy 06P-230 from the angles 06P-220.
(g) Remove the screws 06P-240, the washers 06P-250 and the angles 06P-220
from the aft side wall assembly 06P-010.
(h) Remove the screws 06P-310, the washers 06P-250 and the angle 06P-340
from the aft side wall assembly 06P-010.
(j) Remove the screws 06P-350 and the single door emergency unlocking device
assembly 06P-360 from the post assembly 06P-270.
(k) Disassemble the single door emergency unlocking device assembly 06P-360
as follows:
For Myanmar Airways (MMA) use only
1 Remove the bolt 06P-420 and the emergency unlocking device strike
06P-380 from the emergency unlocking device housing 06P-370.
2 Remove the pin 06P-400, the snap catch 06P-410 and the emergency
unlocking device pivot 06P-390 from the emergency unlocking device
housing 06P-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06P-410 and the pin 06P-400.
(m) Remove the screws 06P-310, 06P-330, the washers 06P-250 and the post
assembly 06P-270.
1 Remove the screws 06P-280 and the plates 06P-300 from the post
assembly 06P-270.
(o) Remove the screws 06P-440 and the toilet seat-cover dispenser 06P-430 from
the aft side wall assembly 06P-010.
(p) Remove the screws 06P-040, 06P-050 and the fittings 06P-020, 06P-030.
SUBTASK 25-41-58-010-022-G01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3093
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06P-160 from the handle assemblies 06P-140.
2 Remove the handle assemblies 06P-140 from the aft side wall assembly
06P-010.
3 Remove the special screws 06P-150 and the special washers 06P-170
from the aft side wall assembly 06P-010.
(b) Remove the studs 06P-260 and the washers 06P-250 from the oxygen
container assy cover 06P-180.
(c) Remove the screws 06P-200, the nuts 06P-210 and the oxygen container assy
cover 06P-180 from the angle 06P-190.
(d) Remove the screws 06P-240, the washers 06P-250 and the angle 06P-190
from the aft side wall assembly 06P-010.
(e) Remove the ground cable from the oxygen container assy 06P-230.
(f) Remove the screws 06P-240, the washers 06P-250 and the oxygen container
assy 06P-230 from the angles 06P-220.
(g) Remove the screws 06P-240, the washers 06P-250 and the angles 06P-220
from the aft side wall assembly 06P-010.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06P-310, the washers 06P-250 and the angle 06P-340
from the aft side wall assembly 06P-010.
(j) Remove the screws 06P-350 and the single door emergency unlocking device
assembly 06P-360 from the post assembly 06P-270.
(k) Disassemble the single door emergency unlocking device assembly 06P-360
as follows:
1 Remove the bolt 06P-420 and the emergency unlocking device strike
06P-380 from the emergency unlocking device housing 06P-370.
2 Remove the pin 06P-400, the snap catch 06P-410 and the emergency
unlocking device pivot 06P-390 from the emergency unlocking device
housing 06P-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06P-410 and the pin 06P-400.
(l) Remove the caps 06P-320, the screws 06P-310, 06P-330, the washers
06P-250 and the post assembly 06P-270.
1 Remove the screws 06P-280 and the plates 06P-300 from the post
assembly 06P-270.
(n) Remove the screws 06P-440 and the toilet seat-cover dispenser 06P-430 from
the aft side wall assembly 06P-010.
For Myanmar Airways (MMA) use only
(p) Remove the screws 06P-040, 06P-050 and the fittings 06P-020, 06P-030.
SUBTASK 25-41-58-010-022-H01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3094
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06P-160 from the handle assemblies 06P-140.
2 Remove the handle assemblies 06P-140 from the aft side wall assembly
06P-010.
3 Remove the special screws 06P-150 and the special washers 06P-170
from the aft side wall assembly 06P-010.
(b) Remove the studs 06P-260 and the washers 06P-250 from the oxygen
container assy cover 06P-180.
(c) Remove the screws 06P-200, the nuts 06P-210 and the oxygen container assy
cover 06P-180 from the angle 06P-190.
(d) Remove the screws 06P-240, the washers 06P-250 and the angle 06P-190
from the aft side wall assembly 06P-010.
(e) Remove the ground cable from the oxygen container assy 06P-230.
For Myanmar Airways (MMA) use only
(f) Remove the screws 06P-240, the washers 06P-250 and the oxygen container
assy 06P-230 from the angles 06P-220.
(g) Remove the screws 06P-240, the washers 06P-250 and the angles 06P-220
from the aft side wall assembly 06P-010.
(h) Remove the screws 06P-310, the washers 06P-250 and the angle 06P-340
from the aft side wall assembly 06P-010.
(j) Remove the screws 06P-350 and the single door emergency unlocking device
assembly 06P-360 from the post assembly 06P-270.
(k) Disassemble the single door emergency unlocking device assembly 06P-360
as follows:
1 Remove the bolt 06P-420 and the emergency unlocking device strike
06P-380 from the emergency unlocking device housing 06P-370.
2 Remove the pin 06P-400, the snap catch 06P-410 and the emergency
unlocking device pivot 06P-390 from the emergency unlocking device
housing 06P-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06P-410 and the pin 06P-400.
(l) Remove the caps 06P-320, the screws 06P-310, 06P-330, the washers
06P-250 and the post assembly 06P-270.
1 Remove the screws 06P-280 and the plates 06P-300 from the post
assembly 06P-270.
(n) Remove the screws 06P-040, 06P-050 and the fittings 06P-020, 06P-030.
TASK 25-41-58-000-804-R01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-023-A01
For Myanmar Airways (MMA) use only
D2549010414200
(1) Removal of the Side Wall (06Q-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3095
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06Q-320 from the handle assembly 06Q-300.
2 Remove the handle assembly 06Q-300 from the aft side wall assembly
06Q-010.
3 Remove the special screws 06Q-310 and the special washers 06Q-330
from the aft side wall assembly 06Q-010.
(b) Remove the screws 06Q-440, the washers 06Q-210 and the support 06Q-340
from the aft side wall assembly 06Q-010.
(c) Remove the studs 06Q-220 and the washers 06Q-210 from the oxygen
container assy cover 06Q-140.
(d) Remove the screws 06Q-160, the nuts 06Q-170 and the oxygen container assy
cover 06Q-140 from the angle 06Q-150.
(e) Remove the screws 06Q-200, the washers 06Q-210 and the angle 06Q-150
from the aft side wall assembly 06Q-010.
(f) Remove the ground cable from the oxygen container assy 06Q-190.
(g) Remove the screws 06Q-200, the washers 06Q-210 and the oxygen container
assy 06Q-190 from the angles 06Q-180.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06Q-200, the washers 06Q-210 and the angles 06Q-180
from the aft side wall assembly 06Q-010.
(j) Remove the screws 06Q-270, the washers 06Q-210 and the angle 06Q-350
from the aft side wall assembly 06Q-010.
(k) Remove the screws 06Q-430 and the single door emergency unlocking device
assembly 06Q-360 from the post assembly 06Q-230.
(l) Disassemble the single door emergency unlocking device assembly 06Q-360
as follows:
1 Remove the bolt 06Q-420 and the emergency unlocking device strike
06Q-380 from the emergency unlocking device housing 06Q-370.
2 Remove the pin 06Q-400, the snap catch 06Q-410 and the emergency
unlocking device pivot 06Q-390 from the emergency unlocking device
housing 06Q-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06Q-410 and the pin 06Q-400.
(n) Remove the screws 06Q-270, 06Q-450, the washers 06Q-210 and the post
assembly 06Q-230.
1 Remove the screws 06Q-240 and the plates 06Q-260 from the post
assembly 06Q-230.
(q) Remove the screws 06Q-470 and the toilet seat-cover dispenser 06Q-460 from
the aft side wall assembly 06Q-010.
(r) Remove the screws 06Q-040, 06Q-050 and the fittings 06Q-020, 06Q-030.
SUBTASK 25-41-58-010-023-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3096
For Myanmar Airways (MMA) use only
1 Remove the security pins 06Q-320 from the handle assembly 06Q-300.
2 Remove the handle assembly 06Q-300 from the aft side wall assembly
06Q-010.
3 Remove the special screws 06Q-310 and the special washers 06Q-330
from the aft side wall assembly 06Q-010.
(c) Remove the screws 06Q-440, the washers 06Q-210 and the support 06Q-340
from the aft side wall assembly 06Q-010.
(d) Remove the studs 06Q-220 and the washers 06Q-210 from the oxygen
container assy cover 06Q-140.
(e) Remove the screws 06Q-160, the nuts 06Q-170 and the oxygen container assy
cover 06Q-140 from the angle 06Q-150.
(f) Remove the screws 06Q-200, 06Q-205, the washers 06Q-210, 06Q-215 and
the angle 06Q-150 from the aft side wall assembly 06Q-010.
(g) Remove the ground cable from the oxygen container assy 06Q-190.
(h) Remove the screws 06Q-200, 06Q-205, the washers 06Q-210 and the oxygen
container assy 06Q-190 from the angles 06Q-180.
(j) Remove the screws 06Q-200, the washers 06Q-210 and the angles 06Q-180
from the aft side wall assembly 06Q-010.
(k) Remove the screws 06Q-270, the washers 06Q-210 and the angle 06Q-350
from the aft side wall assembly 06Q-010.
(l) Remove the screws 06Q-430 and the single door emergency unlocking device
assembly 06Q-360 from the post assembly 06Q-230.
(m) Disassemble the single door emergency unlocking device assembly 06Q-360
as follows:
1 Remove the bolt 06Q-420 and the emergency unlocking device strike
06Q-380 from the emergency unlocking device housing 06Q-370.
2 Remove the pin 06Q-400, the snap catch 06Q-410 and the emergency
unlocking device pivot 06Q-390 from the emergency unlocking device
housing 06Q-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06Q-410 and the pin 06Q-400.
(o) Remove the screws 06Q-270, 06Q-450, the washers 06Q-210 and the post
assembly 06Q-230.
1 Remove the screws 06Q-240 and the plates 06Q-260 from the post
assembly 06Q-230.
(q) Remove the screws 06Q-470 and the toilet seat-cover dispenser 06Q-460 from
the aft side wall assembly 06Q-010.
(r) Remove the screws 06Q-040, 06Q-050 and the fittings 06Q-020, 06Q-030.
SUBTASK 25-41-58-010-023-C01
D2549010300000
(0) Removal of the Side Wall (06Q-1)
NOTE: See TABLE for the references for the replacement procedures of
For Myanmar Airways (MMA) use only
Table 3097
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06Q-320 from the handle assembly 06Q-300.
2 Remove the handle assembly 06Q-300 from the aft side wall assembly
06Q-010.
3 Remove the special screws 06Q-310 and the special washers 06Q-330
from the aft side wall assembly 06Q-010.
(b) Remove the screws 06Q-440, the washers 06Q-210 and the support 06Q-340
from the aft side wall assembly 06Q-010.
(c) Remove the studs 06Q-220 and the washers 06Q-210 from the oxygen
container assy cover 06Q-140.
(d) Remove the screws 06Q-160, the nuts 06Q-170 and the oxygen container assy
cover 06Q-140 from the angle 06Q-150.
(e) Remove the screws 06Q-200, the washers 06Q-210 and the angle 06Q-150
from the aft side wall assembly 06Q-010.
(f) Remove the ground cable from the oxygen container assy 06Q-190.
(g) Remove the screws 06Q-200, the washers 06Q-210 and the oxygen container
assy 06Q-190 from the angles 06Q-180.
(h) Remove the screws 06Q-200, the washers 06Q-210 and the angles 06Q-180
from the aft side wall assembly 06Q-010.
For Myanmar Airways (MMA) use only
(j) Remove the screws 06Q-270, the washers 06Q-210 and the angle 06Q-350
from the aft side wall assembly 06Q-010.
(k) Remove the screws 06Q-430 and the single door emergency unlocking device
assembly 06Q-360 from the post assembly 06Q-230.
(l) Disassemble the single door emergency unlocking device assembly 06Q-360
as follows:
1 Remove the bolt 06Q-420 and the emergency unlocking device strike
06Q-380 from the emergency unlocking device housing 06Q-370.
2 Remove the pin 06Q-400, the snap catch 06Q-410 and the emergency
unlocking device pivot 06Q-390 from the emergency unlocking device
housing 06Q-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06Q-410 and the pin 06Q-400.
(n) Remove the screws 06Q-270, 06Q-450, the washers 06Q-210 and the post
assembly 06Q-230.
1 Remove the screws 06Q-240 and the plates 06Q-260 from the post
For Myanmar Airways (MMA) use only
assembly 06Q-230.
(q) Remove the screws 06Q-470 and the toilet seat-cover dispenser 06Q-460 from
the aft side wall assembly 06Q-010.
(r) Remove the screws 06Q-040, 06Q-050 and the fittings 06Q-020, 06Q-030.
SUBTASK 25-41-58-010-023-E01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3098
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06Q-320 from the handle assembly 06Q-300.
2 Remove the handle assembly 06Q-300 from the aft side wall assembly
06Q-010.
3 Remove the special screws 06Q-310 and the special washers 06Q-330
from the aft side wall assembly 06Q-010.
(b) Remove the screws 06Q-440, the washers 06Q-210 and the support 06Q-340
from the aft side wall assembly 06Q-010.
(c) Remove the studs 06Q-220 and the washers 06Q-210 from the oxygen
container assy cover 06Q-140.
For Myanmar Airways (MMA) use only
(d) Remove the screws 06Q-160, the nuts 06Q-170 and the oxygen container assy
cover 06Q-140 from the angle 06Q-150.
(e) Remove the screws 06Q-200, the washers 06Q-210 and the angle 06Q-150
from the aft side wall assembly 06Q-010.
(f) Remove the ground cable from the oxygen container assy 06Q-190.
(g) Remove the screws 06Q-200, the washers 06Q-210 and the oxygen container
assy 06Q-190 from the angles 06Q-180.
(h) Remove the screws 06Q-200, the washers 06Q-210 and the angles 06Q-180
from the aft side wall assembly 06Q-010.
(j) Remove the screws 06Q-270, the washers 06Q-210 and the angle 06Q-350
from the aft side wall assembly 06Q-010.
(k) Remove the screws 06Q-430 and the single door emergency unlocking device
assembly 06Q-360 from the post assembly 06Q-230.
(l) Disassemble the single door emergency unlocking device assembly 06Q-360
as follows:
1 Remove the bolt 06Q-420 and the emergency unlocking device strike
06Q-380 from the emergency unlocking device housing 06Q-370.
2 Remove the pin 06Q-400, the snap catch 06Q-410 and the emergency
unlocking device pivot 06Q-390 from the emergency unlocking device
housing 06Q-370.
NOTE: If necessary use a hot air blower to heat up the Material No.
For Myanmar Airways (MMA) use only
(n) Remove the screws 06Q-270, 06Q-450, the washers 06Q-210 and the post
assembly 06Q-230.
1 Remove the screws 06Q-240 and the plates 06Q-260 from the post
assembly 06Q-230.
(q) Remove the screws 06Q-040, 06Q-050 and the fittings 06Q-020, 06Q-030.
TASK 25-41-58-000-804-S01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-024-A01
For Myanmar Airways (MMA) use only
D2549030809400
(1) Removal of the Side Wall (06R-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3099
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(b) Remove the studs 06R-290 and the washers 06R-280 from the oxygen
container assy cover 06R-210.
(c) Remove the screws 06R-230, the nuts 06R-240 and the oxygen container assy
cover 06R-210 from the angle 06R-220.
(d) Remove the screws 06R-270, the washers 06R-280 and the angle 06R-220
from the aft side wall assembly 06R-010.
(e) Remove the ground cable from the oxygen container assy 06R-260.
(f) Remove the screws 06R-270, the washers 06R-280 and the oxygen container
assy 06R-260 from the angles 06R-250.
(g) Remove the screws 06R-270, the washers 06R-280 and the angles 06R-250
from the aft side wall assembly 06R-010.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06R-340, the washers 06R-280 and the angle 06R-380
from the aft side wall assembly 06R-010.
(j) Remove the screws 06R-390 and the single door emergency unlocking device
assembly 06R-400 from the post assembly 06R-300.
(k) Disassemble the single door emergency unlocking device assembly 06R-400
as follows:
1 Remove the bolt 06R-460 and the emergency unlocking device strike
06R-420 from the emergency unlocking device housing 06R-410.
2 Remove the pin 06R-440, the snap catch 06R-450 and the emergency
unlocking device pivot 06R-430 from the emergency unlocking device
housing 06R-410.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06R-450 and the pin 06R-440.
(m) Remove the screws 06R-340, 06R-370 and the washers 06R-280 from the
post assembly 06R-300.
1 Remove the screws 06R-310 and the plates 06R-330 from the post
For Myanmar Airways (MMA) use only
assembly 06R-300.
(o) Remove the screws 06R-040, 06R-050 and the fittings 06R-020, 06R-030.
SUBTASK 25-41-58-010-024-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3100
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06R-490 from the handle assemblies 06R-470.
2 Remove the handle assemblies 06R-470 from the aft side wall assembly
06R-010.
3 Remove the special screws 06R-480 and the special washers 06R-500
from the aft side wall assembly 06R-010.
(b) Remove the studs 06R-290 and the washers 06R-280 from the oxygen
container assy cover 06R-210.
(c) Remove the screws 06R-230, the nuts 06R-240 and the oxygen container assy
cover 06R-210 from the angle 06R-220.
(d) Remove the screws 06R-270, the washers 06R-280 and the angle 06R-220
from the aft side wall assembly 06R-010.
For Myanmar Airways (MMA) use only
(e) Remove the ground cable from the oxygen container assy 06R-260.
(f) Remove the screws 06R-270, the washers 06R-280 and the oxygen container
assy 06R-260 from the angles 06R-250.
(g) Remove the screws 06R-270, 06R-275, the washers 06R-280 and the oxygen
container assy 06R-260 from the angles 06R-250.
(h) Remove the screws 06R-270, the washers 06R-280 and the angles 06R-250
from the aft side wall assembly 06R-010.
(j) Remove the screws 06R-340, the washers 06R-280 and the angle 06R-380
from the aft side wall assembly 06R-010.
(k) Remove the screws 06R-390 and the single door emergency unlocking device
assembly 06R-400 from the post assembly 06R-300.
(l) Disassemble the single door emergency unlocking device assembly 06R-400
as follows:
1 Remove the bolt 06R-460 and the emergency unlocking device strike
06R-420 from the emergency unlocking device housing 06R-410.
2 Remove the pin 06R-440, the snap catch 06R-450 and the emergency
unlocking device pivot 06R-430 from the emergency unlocking device
housing 06R-410.
NOTE: If necessary use a hot air blower to heat up the Material No.
For Myanmar Airways (MMA) use only
(n) Remove the screws 06R-340, 06R-370 and the washers 06R-280 from the
post assembly 06R-300.
1 Remove the screws 06R-310 and the plates 06R-330 from the post
assembly 06R-300.
(q) Remove the screws 06R-040, 06R-050 and the fittings 06R-020, 06R-030.
SUBTASK 25-41-58-010-024-C01
D2549010301000 D2549026002600
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3101
For Myanmar Airways (MMA) use only
1 Remove the security pins 06R-490 from the handle assemblies 06R-470.
2 Remove the handle assemblies 06R-470 from the aft side wall assembly
06R-010.
3 Remove the special screws 06R-480 and the special washers 06R-500
from the aft side wall assembly 06R-010.
(b) Remove the studs 06R-290 and the washers 06R-280 from the oxygen
container assy cover 06R-210.
(c) Remove the screws 06R-230, the nuts 06R-240 and the oxygen container assy
cover 06R-210 from the angle 06R-220.
(d) Remove the screws 06R-270, the washers 06R-280 and the angle 06R-220
from the aft side wall assembly 06R-010.
(e) Remove the ground cable from the oxygen container assy 06R-260.
(f) Remove the screws 06R-270, the washers 06R-280 and the oxygen container
assy 06R-260 from the angles 06R-250.
(g) Remove the screws 06R-270, the washers 06R-280 and the angles 06R-250
from the aft side wall assembly 06R-010.
(h) Remove the screws 06R-340, the washers 06R-280 and the angle 06R-380
from the aft side wall assembly 06R-010.
(j) Remove the screws 06R-390 and the single door emergency unlocking device
assembly 06R-400 from the post assembly 06R-300.
(k) Disassemble the single door emergency unlocking device assembly 06R-400
as follows:
1 Remove the bolt 06R-460 and the emergency unlocking device strike
06R-420 from the emergency unlocking device housing 06R-410.
For Myanmar Airways (MMA) use only
2 Remove the pin 06R-440, the snap catch 06R-450 and the emergency
unlocking device pivot 06R-430 from the emergency unlocking device
housing 06R-410.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06R-450 and the pin 06R-440.
(m) Remove the screws 06R-340, 06R-370 and the washers 06R-280 from the
post assembly 06R-300.
1 Remove the screws 06R-310 and the plates 06R-330 from the post
assembly 06R-300.
(o) Remove the screws 06R-040, 06R-050 and the fittings 06R-020, 06R-030.
TASK 25-41-58-000-804-T01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-025-A01
For Myanmar Airways (MMA) use only
D2549020910800
(1) Removal of the Side Wall (06S-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3102
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06S-160 from the handle assemblies 06S-140.
2 Remove the handle assemblies 06S-140 from the aft side wall assembly
06S-010.
3 Remove the special screws 06S-150 and the special washers 06S-170
from the aft side wall assembly 06S-010.
(b) Remove the studs 06S-260 and the washers 06S-250 from the oxygen
container assy cover 06S-180.
(c) Remove the screws 06S-200, the nuts 06S-210 and the oxygen container assy
cover 06S-180 from the angle 06S-190.
(d) Remove the screws 06S-240, the washers 06S-250 and the angle 06S-190
from the aft side wall assembly 06S-010.
(e) Remove the ground cable from the oxygen container assy 06S-230.
(f) Remove the screws 06S-240, the washers 06S-250 and the oxygen container
assy 06S-230 from the angles 06S-220.
(g) Remove the screws 06S-240, the washers 06S-250 and the angles 06S-220
from the aft side wall assembly 06S-010.
For Myanmar Airways (MMA) use only
(h) Remove the screws 06S-310, the washers 06S-250 and the angle 06S-350
from the aft side wall assembly 06S-010.
(j) Remove the screws 06S-360 and the single door emergency unlocking device
assembly 06S-370 from the post assembly 06S-270.
(k) Disassemble the single door emergency unlocking device assembly 06S-370
as follows:
1 Remove the bolt 06S-430 and the emergency unlocking device strike
06S-390 from the emergency unlocking device housing 06S-380.
2 Remove the pin 06S-410, the snap catch 06S-420 and the emergency
unlocking device pivot 06S-400 from the emergency unlocking device
housing 06S-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06S-420 and the pin 06S-410.
(l) Remove the caps 06S-470, the screws 06S-310, 06S-340, the washers
06S-250 and the post assembly 06S-270.
1 Remove the screws 06S-280 and the plates 06S-300 from the post
assembly 06S-270.
(n) Remove the screws 06S-040, 06S-050 and the fittings 06S-020, 06S-030.
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-010-025-B01
D2549026004000 D2549030811400
(0) Removal of the Side Wall (06S-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3103
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06S-160 from the handle assemblies 06S-140.
2 Remove the handle assemblies 06S-140 from the aft side wall assembly
06S-010.
3 Remove the special screws 06S-150 and the special washers 06S-170
from the aft side wall assembly 06S-010.
(b) Remove the studs 06S-260 and the washers 06S-250 from the oxygen
container assy cover 06S-180.
(c) Remove the screws 06S-200, the nuts 06S-210 and the oxygen container assy
cover 06S-180 from the angle 06S-190.
(d) Remove the screws 06S-240, the washers 06S-250 and the angle 06S-190
from the aft side wall assembly 06S-010.
(e) Remove the ground cable from the oxygen container assy 06S-230.
(f) Remove the screws 06S-240, the washers 06S-250 and the oxygen container
assy 06S-230 from the angles 06S-220.
For Myanmar Airways (MMA) use only
(g) Remove the screws 06S-240, the washers 06S-250 and the angles 06S-220
from the aft side wall assembly 06S-010.
(h) Remove the screws 06S-310, the washers 06S-250 and the angle 06S-350
from the aft side wall assembly 06S-010.
(j) Remove the screws 06S-360 and the single door emergency unlocking device
assembly 06S-370 from the post assembly 06S-270.
(k) Disassemble the single door emergency unlocking device assembly 06S-370
as follows:
1 Remove the bolt 06S-430 and the emergency unlocking device strike
06S-390 from the emergency unlocking device housing 06S-380.
2 Remove the pin 06S-410, the snap catch 06S-420 and the emergency
unlocking device pivot 06S-400 from the emergency unlocking device
housing 06S-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06S-420 and the pin 06S-410.
(m) Remove the screws 06S-310, 06S-340, the washers 06S-250 and the post
assembly 06S-270.
1 Remove the screws 06S-280 and the plates 06S-300 from the post
assembly 06S-270.
(o) Remove the screws 06S-450 and the toilet seat-cover dispenser 06S-440 from
the aft side wall assembly 06S-010.
(p) Remove the screw 06S-361 and the coat hook 06S-460 from the aft side wall
assembly 06S-010.
(q) Remove the screws 06S-040, 06S-050 and the fittings 06S-020, 06S-030.
SUBTASK 25-41-58-010-025-C01
D2549020913600
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3104
For Myanmar Airways (MMA) use only
1 Remove the security pins 06S-160 from the handle assemblies 06S-140.
2 Remove the handle assemblies 06S-140 from the aft side wall assembly
06S-010.
3 Remove the special screws 06S-150 and the special washers 06S-170
from the aft side wall assembly 06S-010.
(b) Remove the studs 06S-260 and the washers 06S-250 from the oxygen
container assy cover 06S-180.
(c) Remove the screws 06S-200, the nuts 06S-210 and the oxygen container assy
cover 06S-180 from the angle 06S-190.
(d) Remove the screws 06S-240, the washers 06S-250 and the angle 06S-190
from the aft side wall assembly 06S-010.
(e) Remove the ground cable from the oxygen container assy 06S-230.
(f) Remove the screws 06S-240, the washers 06S-250 and the oxygen container
assy 06S-230 from the angles 06S-220.
(g) Remove the screws 06S-240, the washers 06S-250 and the angles 06S-220
from the aft side wall assembly 06S-010.
(h) Remove the screws 06S-310, the washers 06S-250 and the angle 06S-350
from the aft side wall assembly 06S-010.
(j) Remove the screws 06S-360 and the single door emergency unlocking device
assembly 06S-370 from the post assembly 06S-270.
(k) Disassemble the single door emergency unlocking device assembly 06S-370
as follows:
1 Remove the bolt 06S-430 and the emergency unlocking device strike
06S-390 from the emergency unlocking device housing 06S-380.
For Myanmar Airways (MMA) use only
2 Remove the pin 06S-410, the snap catch 06S-420 and the emergency
unlocking device pivot 06S-400 from the emergency unlocking device
housing 06S-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06S-420 and the pin 06S-410.
(m) Remove the screws 06S-310, 06S-340, the washers 06S-250 and the post
assembly 06S-270.
1 Remove the screws 06S-280 and the plates 06S-300 from the post
assembly 06S-270.
(o) Remove the screws 06S-450 and the toilet seat-cover dispenser 06S-440 from
the aft side wall assembly 06S-010.
(p) Remove the screw 06S-361 and the coat hook 06S-460 from the aft side wall
assembly 06S-010.
(q) Remove the screws 06S-040, 06S-050 and the fittings 06S-020, 06S-030.
SUBTASK 25-41-58-010-025-D01
D2549020914000
(0) Removal of the Side Wall (06S-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
For Myanmar Airways (MMA) use only
Table 3105
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06S-160 from the handle assemblies 06S-140.
2 Remove the handle assemblies 06S-140 from the aft side wall assembly
06S-010.
3 Remove the special screws 06S-150 and the special washers 06S-170
from the aft side wall assembly 06S-010.
(b) Remove the studs 06S-260 and the washers 06S-250 from the oxygen
container assy cover 06S-180.
(c) Remove the screws 06S-200, the nuts 06S-210 and the oxygen container assy
cover 06S-180 from the angle 06S-190.
(d) Remove the screws 06S-240, the washers 06S-250 and the angle 06S-190
from the aft side wall assembly 06S-010.
(e) Remove the ground cable from the oxygen container assy 06S-230.
(f) Remove the screws 06S-240, the washers 06S-250 and the oxygen container
assy 06S-230 from the angles 06S-220.
(g) Remove the screws 06S-240, the washers 06S-250 and the angles 06S-220
from the aft side wall assembly 06S-010.
(h) Remove the screws 06S-310, the washers 06S-250 and the angle 06S-350
from the aft side wall assembly 06S-010.
(j) Remove the screws 06S-360 and the single door emergency unlocking device
assembly 06S-370 from the post assembly 06S-270.
For Myanmar Airways (MMA) use only
(k) Disassemble the single door emergency unlocking device assembly 06S-370
as follows:
1 Remove the bolt 06S-430 and the emergency unlocking device strike
06S-390 from the emergency unlocking device housing 06S-380.
2 Remove the pin 06S-410, the snap catch 06S-420 and the emergency
unlocking device pivot 06S-400 from the emergency unlocking device
housing 06S-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06S-420 and the pin 06S-410.
(m) Remove the screws 06S-310, 06S-340, the washers 06S-250 and the post
assembly 06S-270.
1 Remove the screws 06S-280 and the plates 06S-300 from the post
assembly 06S-270.
(o) Remove the screws 06S-450 and the toilet seat-cover dispenser 06S-440 from
the aft side wall assembly 06S-010.
(p) Remove the screws 06S-040, 06S-050 and the fittings 06S-020, 06S-030.
SUBTASK 25-41-58-010-025-E01
For Myanmar Airways (MMA) use only
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3106
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06S-160 from the handle assemblies 06S-140.
2 Remove the handle assemblies 06S-140 from the aft side wall assembly
06S-010.
3 Remove the special screws 06S-150 and the special washers 06S-170
from the aft side wall assembly 06S-010.
(b) Remove the studs 06S-260 and the washers 06S-250 from the oxygen
container assy cover 06S-180.
(c) Remove the screws 06S-200, the nuts 06S-210 and the oxygen container assy
cover 06S-180 from the angle 06S-190.
(d) Remove the screws 06S-240, the washers 06S-250 and the angle 06S-190
from the aft side wall assembly 06S-010.
(e) Remove the ground cable from the oxygen container assy 06S-230.
(f) Remove the screws 06S-240, the washers 06S-250 and the oxygen container
assy 06S-230 from the angles 06S-220.
For Myanmar Airways (MMA) use only
(g) Remove the screws 06S-240, the washers 06S-250 and the angles 06S-220
from the aft side wall assembly 06S-010.
(h) Remove the screws 06S-310, the washers 06S-250 and the angle 06S-350
from the aft side wall assembly 06S-010.
(j) Remove the screws 06S-360 and the single door emergency unlocking device
assembly 06S-370 from the post assembly 06S-270.
(k) Disassemble the single door emergency unlocking device assembly 06S-370
as follows:
1 Remove the bolt 06S-430 and the emergency unlocking device strike
06S-390 from the emergency unlocking device housing 06S-380.
2 Remove the pin 06S-410, the snap catch 06S-420 and the emergency
unlocking device pivot 06S-400 from the emergency unlocking device
housing 06S-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06S-420 and the pin 06S-410.
(m) Remove the screws 06S-310, 06S-340, the washers 06S-250 and the post
assembly 06S-270.
1 Remove the screws 06S-280 and the plates 06S-300 from the post
assembly 06S-270.
(o) Remove the screws 06S-450 and the toilet seat-cover dispenser 06S-440 from
the aft side wall assembly 06S-010.
(p) Remove the screws 06S-040, 06S-050 and the fittings 06S-020, 06S-030.
SUBTASK 25-41-58-010-025-F01
D2549010414000
(0) Removal of the Side Wall (06S-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3107
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
1 Remove the security pins 06S-160 from the handle assemblies 06S-140.
2 Remove the handle assemblies 06S-140 from the aft side wall assembly
06S-010.
3 Remove the special screws 06S-150 and the special washers 06S-170
from the aft side wall assembly 06S-010.
(b) Remove the studs 06S-260 and the washers 06S-250 from the oxygen
container assy cover 06S-180.
(c) Remove the screws 06S-200, the nuts 06S-210 and the oxygen container assy
cover 06S-180 from the angle 06S-190.
For Myanmar Airways (MMA) use only
(d) Remove the screws 06S-240, the washers 06S-250 and the angle 06S-190
from the aft side wall assembly 06S-010.
(e) Remove the ground cable from the oxygen container assy 06S-230.
(f) Remove the screws 06S-240, the washers 06S-250 and the oxygen container
assy 06S-230 from the angles 06S-220.
(g) Remove the screws 06S-240, the washers 06S-250 and the angles 06S-220
from the aft side wall assembly 06S-010.
(h) Remove the screws 06S-310, the washers 06S-250 and the angle 06S-350
from the aft side wall assembly 06S-010.
(j) Remove the screws 06S-360 and the single door emergency unlocking device
assembly 06S-370 from the post assembly 06S-270.
(k) Disassemble the single door emergency unlocking device assembly 06S-370
as follows:
1 Remove the bolt 06S-430 and the emergency unlocking device strike
06S-390 from the emergency unlocking device housing 06S-380.
2 Remove the pin 06S-410, the snap catch 06S-420 and the emergency
unlocking device pivot 06S-400 from the emergency unlocking device
housing 06S-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
For Myanmar Airways (MMA) use only
(m) Remove the screws 06S-310, 06S-340, the washers 06S-250 and the post
assembly 06S-270.
1 Remove the screws 06S-280 and the plates 06S-300 from the post
assembly 06S-270.
(o) Remove the screws 06S-040, 06S-050 and the fittings 06S-020, 06S-030.
SUBTASK 25-41-58-010-025-G01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3108
For Myanmar Airways (MMA) use only
1 Remove the security pins 06S-160 from the handle assemblies 06S-140.
2 Remove the handle assemblies 06S-140 from the aft side wall assembly
06S-010.
3 Remove the special screws 06S-150 and the special washers 06S-170
from the aft side wall assembly 06S-010.
(b) Remove the studs 06S-260 and the washers 06S-250 from the oxygen
container assy cover 06S-180.
(c) Remove the screws 06S-200, the nuts 06S-210 and the oxygen container assy
cover 06S-180 from the angle 06S-190.
(d) Remove the screws 06S-240, the washers 06S-250 and the angle 06S-190
from the aft side wall assembly 06S-010.
(e) Remove the ground cable from the oxygen container assy 06S-230.
(f) Remove the screws 06S-240, 06S-245, the washers 06S-250 and the oxygen
container assy 06S-230 from the angles 06S-220.
(g) Remove the screws 06S-240, the washers 06S-250 and the angles 06S-220
from the aft side wall assembly 06S-010.
(h) Remove the screws 06S-310, the washers 06S-250 and the angle 06S-350
from the aft side wall assembly 06S-010.
(j) Remove the screws 06S-360 and the single door emergency unlocking device
assembly 06S-370 from the post assembly 06S-270.
(k) Disassemble the single door emergency unlocking device assembly 06S-370
as follows:
1 Remove the bolt 06S-430 and the emergency unlocking device strike
06S-390 from the emergency unlocking device housing 06S-380.
For Myanmar Airways (MMA) use only
2 Remove the pin 06S-410, the snap catch 06S-420 and the emergency
unlocking device pivot 06S-400 from the emergency unlocking device
housing 06S-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06S-420 and the pin 06S-410.
(m) Remove the screws 06S-310, 06S-340, the washers 06S-250 and the post
assembly 06S-270.
1 Remove the screws 06S-280 and the plates 06S-300 from the post
assembly 06S-270.
(o) Remove the screws 06S-040, 06S-050 and the fittings 06S-020, 06S-030.
TASK 25-41-58-000-804-U01
D2549026003400 D2549030812200
26. Removal of the Side Wall
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-026-A01
For Myanmar Airways (MMA) use only
D2549026003400
(1) Removal of the Side Wall (06T-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
1 Remove the security pins 06T-160 from the handle assemblies 06T-140.
2 Remove the handle assemblies 06T-140 from the aft side wall assembly
06T-010.
3 Remove the special screws 06T-150 and the special washers 06T-170
from the aft side wall assembly 06T-010.
(b) Remove the studs 06T-260 and the washers 06T-250 from the oxygen
container assy cover 06T-180.
(c) Remove the screws 06T-200, the nuts 06T-210 and the oxygen container assy
cover 06T-180 from the angle 06T-190.
(d) Remove the screws 06T-240, the washers 06T-250 and the angle 06T-190
from the aft side wall assembly 06T-010.
(e) Remove the ground cable from the oxygen container assy 06T-230.
(f) Remove the screws 06T-240, the washers 06T-250 and the oxygen container
assy 06T-230 from the angles 06T-220.
For Myanmar Airways (MMA) use only
(g) Remove the screws 06T-240, the washers 06T-250 and the angles 06T-220
from the aft side wall assembly 06T-010.
(h) Remove the screws 06T-310, the washers 06T-250 and the angle 06T-350
from the aft side wall assembly 06T-010.
(j) Remove the screws 06T-360 and the single door emergency unlocking device
assembly 06T-370 from the post assembly 06T-270.
(k) Disassemble the single door emergency unlocking device assembly 06T-370
as follows:
1 Remove the bolt 06T-430 and the emergency unlocking device strike
06T-390 from the emergency unlocking device housing 06T-380.
2 Remove the pin 06T-410, the snap catch 06T-420 and the emergency
unlocking device pivot 06T-400 from the emergency unlocking device
housing 06T-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06T-420 and the pin 06T-410.
(m) Remove the screws 06T-310, 06T-340, the washers 06T-250 and the post
assembly 06T-270.
1 Remove the screws 06T-280 and the plates 06T-300 from the post
assembly 06T-270.
(o) Remove the screws 06T-040, 06T-050 and the fittings 06T-020, 06T-030.
SUBTASK 25-41-58-010-026-B01
D2549030812200
(0) Removal of the Side Wall (06T-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
1 Remove the setscrews 06T-480 and the handle 06T-450 from the screws
06T-460.
2 Remove the screws 06T-460 and the washers 06T-470 from the aft side
wall assembly 06T-010.
(b) Remove the studs 06T-260 and the washers 06T-250 from the oxygen
container assy cover 06T-180.
(c) Remove the screws 06T-200, the nuts 06T-210 and the oxygen container assy
cover 06T-180 from the angle 06T-190.
(d) Remove the screws 06T-240, the washers 06T-250 and the angle 06T-190
from the aft side wall assembly 06T-010.
(e) Remove the ground cable from the oxygen container assy 06T-230.
For Myanmar Airways (MMA) use only
(f) Remove the screws 06T-240, the washers 06T-250 and the oxygen container
assy 06T-230 from the angles 06T-220.
(g) Remove the screws 06T-240, the washers 06T-250 and the angles 06T-220
from the aft side wall assembly 06T-010.
(h) Remove the screws 06T-310, the washers 06T-250 and the angle 06T-350
from the aft side wall assembly 06T-010.
(j) Remove the screws 06T-360 and the single door emergency unlocking device
assembly 06T-370 from the post assembly 06T-270.
(k) Disassemble the single door emergency unlocking device assembly 06T-370
as follows:
1 Remove the bolt 06T-430 and the emergency unlocking device strike
06T-390 from the emergency unlocking device housing 06T-380.
2 Remove the pin 06T-410, the snap catch 06T-420 and the emergency
unlocking device pivot 06T-400 from the emergency unlocking device
housing 06T-380.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the snap catch
06T-420 and the pin 06T-410.
(m) Remove the screws 06T-310, 06T-340, the washers 06T-250 and the post
assembly 06T-270.
1 Remove the screws 06T-280 and the plates 06T-300 from the post
assembly 06T-270.
(o) Remove the screws 06T-040, 06T-050 and the fittings 06T-020, 06T-030.
TASK 25-41-58-000-805-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-027-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material No. 08-026
Adhesive/Sealant
one Part, RTV
Silicone Rubber
(a) Remove the stud 07-180 from the housing assembly 07-010.
(b) Remove the glass mirror 07-170 from the screws 07-190.
(c) Remove the screws 07-190 from the housing assembly 07-010.
(d) Remove the screws 07-260 and the decor covers 07-250 from the housing
assembly 07-010.
3 Remove the screws 07-140, the washers 07-160 and the housing
assembly 07-010 from the lavatory structure.
SUBTASK 25-41-58-010-027-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Silicone Rubber
(a) Remove the stud 07-180 from the housing assembly 07-010.
(b) Remove the mirror assembly 07-172 from the screws 07-190.
(c) Remove the screws 07-190 from the housing assembly 07-010.
(d) Remove the screws 07-260 and the decor covers 07-250 from the housing
assembly 07-010.
3 Remove the screws 07-140, the washers 07-160 and the housing
assembly 07-010 from the lavatory structure.
SUBTASK 25-41-58-010-027-C01
For Myanmar Airways (MMA) use only
D2549010408000 D2549010408600
(0) Removal of the Housing (07-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Adhesive/Sealant
one Part, RTV
Silicone Rubber
(a) Remove the stud 07-180 from the housing assembly 07-010.
(b) Remove the glass mirror 07-170 from the screws 07-190.
(c) Remove the screws 07-190 from the housing assembly 07-010.
(d) Remove the screws 07-260 and the decor covers 07-270, 07-280 from the
housing assembly 07-010.
3 Remove the screws 07-140, the washers 07-160 and the housing
assembly 07-010 from the lavatory structure.
SUBTASK 25-41-58-010-027-D01
D2549020302400 D2549020307400
(0) Removal of the Housing (07-1)
NOTE: See TABLE for the references for the replacement procedures of
For Myanmar Airways (MMA) use only
(a) Remove the stud 07-180 from the housing assembly 07-010.
(b) Remove the glass mirror 07-170 from the screws 07-190.
(c) Remove the screws 07-190 from the housing assembly 07-010.
(d) Remove the screws 07-260 and the decor covers 07-270, 07-280 from the
housing assembly 07-010.
3 Remove the screws 07-140, the washers 07-160 and the housing
assembly 07-010 from the lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-805-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-028-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material
No. 08-026
Adhesive/Sealant
one Part, RTV
Silicone Rubber
(a) Remove the stud 07A-190 from the housing assembly 07A-010.
(b) Remove the glass mirror 07A-180 from the screws 07A-200.
(c) Remove the screws 07A-200 from the housing assembly 07A-010.
(d) Remove the screws 07A-280 and the decor covers 07A-270, 07A-271 from the
housing assembly 07A-010.
3 Remove the screws 07A-150, the washers 07A-170 and the housing
assembly 07A-010 from the lavatory structure.
SUBTASK 25-41-58-010-028-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Material
No. 08-026
Adhesive/Sealant
one Part, RTV
Silicone Rubber
(a) Remove the stud 07A-190 from the housing assembly 07A-010.
(b) Remove the glass mirror 07A-180 from the screws 07A-200.
(c) Remove the screws 07A-200 from the housing assembly 07A-010.
(d) Remove the screws 07A-280 and the decor covers 07A-270, 07A-275 from the
housing assembly 07A-010.
3 Remove the screws 07A-150, the washers 07A-170 and the housing
assembly 07A-010 from the lavatory structure.
SUBTASK 25-41-58-010-028-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
self adhesive
(a) Remove the stud 07A-190 from the housing assembly 07A-010.
(b) Remove the glass mirror 07A-180 from the screws 07A-200.
(c) Remove the screws 07A-200 from the housing assembly 07A-010.
(d) Remove the screws 07A-280 and the decor covers 07A-270, 07A-271, 07A-275
from the housing assembly 07A-010.
3 Remove the screws 07A-150, the washers 07A-170 and the housing
assembly 07A-010 from the lavatory structure.
SUBTASK 25-41-58-010-028-D01
D2549020301200 D2549030707800
(0) Removal of the Housing (07A-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
INSTALLED PARTS
(a) Remove the stud 07A-190 from the housing assembly 07A-010.
(b) Remove the glass mirror 07A-180 from the screws 07A-200.
(c) Remove the screws 07A-200 from the housing assembly 07A-010.
(d) Remove the screws 07A-300, the washers 07A-310 and the soap dispenser
holder 07A-290 from the housing assembly 07A-010.
(e) Remove the screws 07A-340, the cosmetics holder 07A-320 and the spacer
07A-330 from the housing assembly 07A-010.
(f) Remove the screws 07A-280 and the decor covers 07A-270, 07A-271 from the
housing assembly 07A-010.
3 Remove the screws 07A-150, the washers 07A-170 and the housing
assembly 07A-010 from the lavatory structure.
TASK 25-41-58-000-805-C01
A. General
For Myanmar Airways (MMA) use only
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-029-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Material
No. 08-026
Adhesive/Sealant
one Part, RTV
Silicone Rubber
(a) Remove the stud 07B-190 from the housing assembly 07B-010.
(b) Remove the glass mirror 07B-180 from the screws 07B-200.
(c) Remove the screws 07B-200 from the housing assembly 07B-010.
(d) Remove the screws 07B-290 and the decor covers 07B-300 from the housing
assembly 07B-010.
3 Remove the screws 07B-150, the washers 07B-170 and the housing
assembly 07B-010 from the lavatory structure.
SUBTASK 25-41-58-010-029-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Material
No. 08-026
Adhesive/Sealant
one Part, RTV
Silicone Rubber
(a) Remove the stud 07B-190 from the housing assembly 07B-010.
(b) Remove the glass mirror 07B-180 from the screws 07B-200.
(c) Remove the screws 07B-200 from the housing assembly 07B-010.
(d) Remove the screws 07B-290 and the decor covers 07B-270, 07B-280 from the
housing assembly 07B-010.
3 Remove the screws 07B-150, the washers 07B-170 and the housing
assembly 07B-010 from the lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-805-D01
A. General
– Cleaning
For Myanmar Airways (MMA) use only
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-030-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
INSTALLED PARTS
(a) Remove the stud 07C-190 from the housing assembly 07C-010.
(b) Remove the glass mirror 07C-180 from the screws 07C-200.
(c) Remove the screws 07C-200 from the housing assembly 07C-010.
(d) Remove the screws 07C-270 and the decor covers 07C-280 from the housing
assembly 07C-010.
3 Remove the screws 07C-150, the washers 07C-170 and the housing
assembly 07C-010 from the lavatory structure.
SUBTASK 25-41-58-010-030-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07C-190 from the housing assembly 07C-010.
(b) Remove the glass mirror 07C-180 from the screws 07C-200.
For Myanmar Airways (MMA) use only
(c) Remove the screws 07C-200 from the housing assembly 07C-010.
(d) Remove the screws 07C-270 and the decor covers 07C-290, 07C-300 from the
housing assembly 07C-010.
3 Remove the screws 07C-150, the washers 07C-170 and the housing
assembly 07C-010 from the lavatory structure.
SUBTASK 25-41-58-010-030-C01
D2549020305200 D2549030712000
(0) Removal of the Housing (07C-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material
No. 08-026
Adhesive/Sealant
one Part, RTV
Silicone Rubber
(a) Remove the stud 07C-190 from the housing assembly 07C-010.
(b) Remove the glass mirror 07C-180 from the screws 07C-200.
(c) Remove the screws 07C-200 from the housing assembly 07C-010.
(d) Remove the screws 07C-320 and the vase 07C-310 from the housing assembly
07C-010.
(e) Remove the screws 07C-270 and the decor covers 07C-280 from the housing
assembly 07C-010.
3 Remove the screws 07C-150, the washers 07C-170 and the housing
assembly 07C-010 from the lavatory structure.
SUBTASK 25-41-58-010-030-D01
D2549030712200 D2549030808000
(0) Removal of the Housing (07C-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Material
No. 08-026
Adhesive/Sealant
one Part, RTV
Silicone Rubber
(a) Remove the stud 07C-190 from the housing assembly 07C-010.
(b) Remove the glass mirror 07C-180 from the screws 07C-200.
(c) Remove the screws 07C-200 from the housing assembly 07C-010.
(d) Remove the screws 07C-270 and the decor covers 07C-290, 07C-300 from the
housing assembly 07C-010.
3 Remove the screws 07C-150, the washers 07C-170 and the housing
assembly 07C-010 from the lavatory structure.
TASK 25-41-58-000-805-E01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-031-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
INSTALLED PARTS
(a) Remove the stud 07D-190 from the housing assembly 07D-010.
(b) Remove the glass mirror 07D-180 from the screws 07D-200.
(c) Remove the screws 07D-200 from the housing assembly 07D-010.
(d) Remove the screws 07D-290 and the decor covers 07D-270, 07D-280 from the
housing assembly 07D-010.
3 Remove the screws 07D-150, the washers 07D-170 and the housing
assembly 07D-010 from the lavatory structure.
SUBTASK 25-41-58-010-031-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07D-190 from the housing assembly 07D-010.
(b) Remove the glass mirror 07D-180 from the screws 07D-200.
For Myanmar Airways (MMA) use only
(c) Remove the screws 07D-200 from the housing assembly 07D-010.
(d) Remove the screws 07D-290 and the decor covers 07D-270, 07D-271 from the
housing assembly 07D-010.
3 Remove the screws 07D-150, the washers 07D-170 and the housing
assembly 07D-010 from the lavatory structure.
SUBTASK 25-41-58-010-031-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07D-190 from the housing assembly 07D-010.
(b) Remove the mirror assembly 07D-182 from the screws 07D-200.
For Myanmar Airways (MMA) use only
(c) Remove the screws 07D-200 from the housing assembly 07D-010.
(d) Remove the screws 07D-290 and the decor covers 07D-270, 07D-271 from the
housing assembly 07D-010.
3 Remove the screws 07D-150, the washers 07D-170 and the housing
assembly 07D-010 from the lavatory structure.
SUBTASK 25-41-58-010-031-D01
D2549020308400
(0) Removal of the Housing (07D-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material
No. 08-026
Adhesive/Sealant
one Part, RTV
Silicone Rubber
(a) Remove the stud 07D-190 from the housing assembly 07D-010.
(b) Remove the glass mirror 07D-180 from the screws 07D-200.
(c) Remove the screws 07D-200 from the housing assembly 07D-010.
(d) Remove the screws 07D-310 and the vase 07D-300 from the housing assembly
07D-010.
(e) Remove the screws 07D-290 and the decor covers 07D-270, 07D-280 from the
housing assembly 07D-010.
3 Remove the screws 07D-150, the washers 07D-170 and the housing
assembly 07D-010 from the lavatory structure.
SUBTASK 25-41-58-010-031-E01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07D-190 from the housing assembly 07D-010.
(b) Remove the glass mirror 07D-180 from the screws 07D-200.
(c) Remove the screws 07D-200 from the housing assembly 07D-010.
(d) Remove the screws 07D-290 and the decor covers 07D-270, 07D-280 from the
housing assembly 07D-010.
3 Remove the screws 07D-150, the washers 07D-170 and the housing
assembly 07D-010 from the lavatory structure.
TASK 25-41-58-000-805-F01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-032-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Assembly 350-801-A01
self adhesive
INSTALLED PARTS
(a) Remove the stud 07E-190 from the housing assembly 07E-010.
(b) Remove the glass mirror 07E-180 from the screws 07E-200.
(c) Remove the screws 07E-200 from the housing assembly 07E-010.
(d) Remove the screws 07E-290 and the decor covers 07E-270, 07E-280 from the
housing assembly 07E-010.
3 Remove the screws 07E-150, the washers 07E-170 and the housing
assembly 07E-010 from the lavatory structure.
SUBTASK 25-41-58-010-032-B01
D2549020900400 R225401869-000
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
INSTALLED PARTS
(a) Remove the stud 07E-190 from the housing assembly 07E-010.
(b) Remove the glass mirror 07E-180 from the screws 07E-200.
(c) Remove the screws 07E-200 from the housing assembly 07E-010.
(d) Remove the screws 07E-310 and the perfume holder 07E-300 from the
housing assembly 07E-010.
(e) Remove the screws 07E-290 and the decor covers 07E-270, 07E-280 from the
housing assembly 07E-010.
3 Remove the screws 07E-150, the washers 07E-170 and the housing
assembly 07E-010 from the lavatory structure.
SUBTASK 25-41-58-010-032-C01
D2549010410400
(0) Removal of the Housing (07E-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07E-190 from the housing assembly 07E-010.
(b) Remove the glass mirror 07E-180 from the screws 07E-200.
For Myanmar Airways (MMA) use only
(c) Remove the screws 07E-200 from the housing assembly 07E-010.
(d) Remove the screws 07E-310 and the vase 07E-320 from the housing assembly
07E-010.
(e) Remove the screws 07E-330, the washers 07E-340 and the cosmetics holder
07E-300 from the housing assembly 07E-010.
(f) Remove the screws 07E-290 and the decor covers 07E-270, 07E-280 from the
housing assembly 07E-010.
3 Remove the screws 07E-150, the washers 07E-170 and the housing
assembly 07E-010 from the lavatory structure.
TASK 25-41-58-000-805-G01
R225401888-008 R225401888-012
33. Removal of the Housing
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-033-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07F-190 from the housing assembly 07F-010.
(b) Remove the glass mirror 07F-180 from the screws 07F-200.
(c) Remove the screws 07F-200 from the housing assembly 07F-010.
(d) Remove the screws 07F-280 and the decor covers 07F-270 from the housing
assembly 07F-010.
3 Remove the screws 07F-150, the washers 07F-170 and the housing
assembly 07F-010 from the lavatory structure.
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-010-033-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07F-190 from the housing assembly 07F-010.
(b) Remove the mirror assembly 07F-182 from the screws 07F-200.
(c) Remove the screws 07F-200 from the housing assembly 07F-010.
(d) Remove the screws 07F-280 and the decor covers 07F-270 from the housing
assembly 07F-010.
3 Remove the screws 07F-150, the washers 07F-170 and the housing
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-010-033-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Material
No. 08-026
Adhesive/Sealant
one Part, RTV
Silicone Rubber
(a) Remove the stud 07F-190 from the housing assembly 07F-010.
(b) Remove the glass mirror 07F-180 from the screws 07F-200.
(c) Remove the screws 07F-200 from the housing assembly 07F-010.
(d) Remove the screws 07F-280 and the decor covers 07F-271, 07F-320 from the
housing assembly 07F-010.
3 Remove the screws 07F-150, the washers 07F-170 and the housing
assembly 07F-010 from the lavatory structure.
SUBTASK 25-41-58-010-033-D01
D2549010411000
For Myanmar Airways (MMA) use only
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
self adhesive
(a) Remove the stud 07F-190 from the housing assembly 07F-010.
(b) Remove the glass mirror 07F-180 from the screws 07F-200.
(c) Remove the screws 07F-200 from the housing assembly 07F-010.
(d) Remove the screws 07F-300 and the vase 07F-310 from the housing assembly
07F-010.
(e) Remove the screws 07F-300 and the perfume holder 07F-290 from the housing
assembly 07F-010.
(f) Remove the screws 07F-280 and the decor covers 07F-270 from the housing
assembly 07F-010.
3 Remove the screws 07F-150, the washers 07F-170 and the housing
assembly 07F-010 from the lavatory structure.
SUBTASK 25-41-58-010-033-E01
D2549020905200 D2549030807200
(0) Removal of the Housing (07F-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
For Myanmar Airways (MMA) use only
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
self adhesive
(a) Remove the stud 07F-190 from the housing assembly 07F-010.
(b) Remove the glass mirror 07F-180 from the screws 07F-200.
(c) Remove the screws 07F-200 from the housing assembly 07F-010.
(d) Remove the screws 07F-301 and the vase 07F-310 from the housing assembly
07F-010.
(e) Remove the screws 07F-280 and the decor covers 07F-271, 07F-320 from the
housing assembly 07F-010.
3 Remove the screws 07F-150, the washers 07F-170 and the housing
assembly 07F-010 from the lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-805-H01
A. General
For Myanmar Airways (MMA) use only
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-034-A01
(1) Removal of the Housing (07G-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
INSTALLED PARTS
(a) Remove the stud 07G-190 from the housing assembly 07G-010.
(b) Remove the glass mirror 07G-180 from the screws 07G-200.
(c) Remove the screws 07G-200 from the housing assembly 07G-010.
(d) Remove the screws 07G-280 and the decor covers 07G-270, 07G-290 from
the housing assembly 07G-010.
3 Remove the screws 07G-150, the washers 07G-170 and the housing
assembly 07G-010 from the lavatory structure.
(f) Remove the mirror 07G-184, the mirror door panel 07G-186 and the adhesive
film from the mirror assy 07G-182.
(g) Remove the screws 07G-200 and the mirror assy 07G-182.
TASK 25-41-58-000-805-J01
A. General
– Cleaning
For Myanmar Airways (MMA) use only
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-035-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
NAME NAME
INSTALLED PARTS
(a) Remove the stud 07H-190 from the housing assembly 07H-010.
(b) Remove the glass mirror 07H-180 from the screws 07H-200.
(c) Remove the screws 07H-200 from the housing assembly 07H-010.
(d) Remove the screws 07H-280 and the decor covers 07H-270, 07H-275 from the
housing assembly 07H-010.
3 Remove the screws 07H-150, the washers 07H-170 and the housing
assembly 07H-010 from the lavatory structure.
SUBTASK 25-41-58-010-035-B01
D2549020908000 D2549020911200
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
INSTALLED PARTS
(a) Remove the stud 07H-190 from the housing assembly 07H-010.
(b) Remove the mirror assembly 07H-182 from the screws 07H-200.
(c) Remove the screws 07H-200 from the housing assembly 07H-010.
(d) Remove the screws 07H-280 and the decor covers 07H-270, 07H-275 from the
housing assembly 07H-010.
3 Remove the screws 07H-150, the washers 07H-170 and the housing
assembly 07H-010 from the lavatory structure.
SUBTASK 25-41-58-010-035-C01
D2549030807800
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07H-190 from the housing assembly 07H-010.
(b) Remove the glass mirror 07H-180 from the screws 07H-200.
For Myanmar Airways (MMA) use only
(c) Remove the screws 07H-200 from the housing assembly 07H-010.
(d) Remove the screws 07H-340, the cosmetics holder 07H-320 and the spacer
07H-330 from the housing assembly 07H-010.
(e) Remove the screws 07H-300, the washers 07H-310 and the soap dispenser
holder 07H-290 from the housing assembly 07H-010.
(f) Remove the screws 07H-280 and the decor covers 07H-270, 07H-275 from the
housing assembly 07H-010.
3 Remove the screws 07H-150, the washers 07H-170 and the housing
assembly 07H-010 from the lavatory structure.
TASK 25-41-58-000-805-K01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-036-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
self adhesive
(a) Remove the stud 07J-190 from the housing assembly 07J-010.
(b) Remove the glass mirror 07J-180 from the screws 07J-200.
(c) Remove the screws 07J-200 from the housing assembly 07J-010.
(d) Remove the screws 07J-280 and the decor covers 07J-270, 07J-271 from the
housing assembly 07J-010.
3 Remove the screws 07J-150, the washers 07J-170 and the housing
assembly 07J-010 from the lavatory structure.
SUBTASK 25-41-58-010-036-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
INSTALLED PARTS
(a) Remove the stud 07J-190 from the housing assembly 07J-010.
(b) Remove the glass mirror 07J-180 from the screws 07J-200.
(c) Remove the screws 07J-200 from the housing assembly 07J-010.
(d) Remove the screws 07J-280 and the decor covers 07J-270, 07J-290 from the
housing assembly 07J-010.
3 Remove the screws 07J-150, the washers 07J-170 and the housing
assembly 07J-010 from the lavatory structure.
SUBTASK 25-41-58-010-036-C01
D2549010413800
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07J-190 from the housing assembly 07J-010.
(b) Remove the glass mirror 07J-180 from the screws 07J-200.
For Myanmar Airways (MMA) use only
(c) Remove the screws 07J-200 from the housing assembly 07J-010.
(d) Remove the screws 07J-280 and the decor covers 07J-270, 07J-271 from the
housing assembly 07J-010.
(e) Remove the screws 07J-320 and the vase 07J-300 from the housing assembly
07J-010.
(f) Remove the screws 07J-320 and the perfume holder 07J-310 from the housing
assembly 07J-010.
3 Remove the screws 07J-150, the washers 07J-170 and the housing
assembly 07J-010 from the lavatory structure.
TASK 25-41-58-000-805-L01
A. General
– Cleaning
– Visual Inspection
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-037-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
INSTALLED PARTS
(a) Remove the stud 07K-250 from the housing assembly 07K-010.
(b) Remove the glass mirror 07K-240 from the screws 07K-260.
(c) Remove the screws 07K-260 from the housing assembly 07K-010.
(d) Remove the screws 07K-340 and the decor covers 07K-330, 07K-331 from the
housing assembly 07K-010.
3 Remove the screws 07K-150, the washers 07K-170 and the housing
assembly 07K-010 from the lavatory structure.
SUBTASK 25-41-58-010-037-B01
D2549030810200
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
INSTALLED PARTS
(a) Remove the stud 07K-250 from the housing assembly 07K-010.
(b) Remove the mirror assembly 07K-400 from the screws 07K-260.
(c) Remove the screws 07K-260 from the housing assembly 07K-010.
(d) Remove the screws 07K-340 and the decor covers 07K-330, 07K-331 from the
housing assembly 07K-010.
3 Remove the screws 07K-150, the washers 07K-170 and the housing
assembly 07K-010 from the lavatory structure.
SUBTASK 25-41-58-010-037-C01
D2549010414600
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07K-250 from the housing assembly 07K-010.
(b) Remove the glass mirror 07K-240 from the screws 07K-260.
For Myanmar Airways (MMA) use only
(c) Remove the screws 07K-260 from the housing assembly 07K-010.
(d) Remove the screws 07K-360, the washers 07K-390 and the cosmetics holder
07K-350 from the housing assembly 07K-010.
(e) Remove the screws 07K-340 and the decor covers 07K-330, 07K-331 from the
housing assembly 07K-010.
3 Remove the screws 07K-150, the washers 07K-170 and the housing
assembly 07K-010 from the lavatory structure.
SUBTASK 25-41-58-010-037-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07K-250 from the housing assembly 07K-010.
(b) Remove the glass mirror 07K-240 from the screws 07K-260.
For Myanmar Airways (MMA) use only
(c) Remove the screws 07K-260 from the housing assembly 07K-010.
(d) Remove the screws 07K-380 and the vase 07K-370 from the housing assembly
07K-010.
(e) Remove the screws 07K-360, the washers 07K-390 and the cosmetics holder
07K-350 from the housing assembly 07K-010.
(f) Remove the screws 07K-340 and the decor covers 07K-330, 07K-331 from the
housing assembly 07K-010.
3 Remove the screws 07K-150, the washers 07K-170 and the housing
assembly 07K-010 from the lavatory structure.
TASK 25-41-58-000-805-M01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-038-A01
D2549010301000
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07L-250 from the housing assembly 07L-010.
(b) Remove the glass mirror 07L-240 from the screws 07L-260.
For Myanmar Airways (MMA) use only
(c) Remove the screws 07L-260 from the housing assembly 07L-010.
(d) Remove the screws 07L-350 and the decor covers 07L-330, 07L-340 from the
housing assembly 07L-010.
(e) Remove the screws 07L-370 and the perfume holder 07L-360 from the housing
assembly 07L-010.
3 Remove the screws 07L-150, the washers 07L-170 and the housing
assembly 07L-010 from the lavatory structure.
SUBTASK 25-41-58-010-038-B01
D2549010300800
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
INSTALLED PARTS
(a) Remove the stud 07L-250 from the housing assembly 07L-010.
(b) Remove the mirror assembly 07L-242 from the screws 07L-260.
(c) Remove the screws 07L-260 from the housing assembly 07L-010.
(d) Remove the screws 07L-350 and the decor covers 07L-330, 07L-340 from the
housing assembly 07L-010.
(e) Remove the screws 07L-370 and the perfume holder 07L-360 from the housing
assembly 07L-010.
3 Remove the screws 07L-150, the washers 07L-170 and the housing
assembly 07L-010 from the lavatory structure.
SUBTASK 25-41-58-010-038-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the stud 07L-250 from the housing assembly 07L-010.
(b) Remove the glass mirror 07L-240 from the screws 07L-260.
For Myanmar Airways (MMA) use only
(c) Remove the screws 07L-260 from the housing assembly 07L-010.
(d) Remove the screws 07L-350 and the decor covers 07L-330, 07L-340 from the
housing assembly 07L-010.
3 Remove the screws 07L-150, the washers 07L-170 and the housing
assembly 07L-010 from the lavatory structure.
TASK 25-41-58-000-806-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-000-081-A01
(1) Removal of the Door (10-1), (11-1), (11A-1), (11A-1), (11B-1), (11C-1), (11D-1),
(11E-1), (11F-1), (11G-1), (11H-1), (11J-1), (11K-1), (11L-1), (11M-1), (11N-1),
(11P-1), (11Q-1), (11R-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
self adhesive
Table 3152
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screws 10-050, the washers 10-060, the nuts 10-070, the hinge
11-010, 11A-010, 11B-010, 11C-010, 11D-010, 11E-010, 11F-010, 11G-010,
11H-010, 11J-010, 11K-010, 11L-010, 11M-010, 11N-010, 11P-010, 11Q-010 or
11R-010 and the single door assembly 11-001, 11A-001, 11B-001, 11C-001,
11D-001, 11E-001, 11F-001, 11G-001, 11H-001, 11J-001, 11K-001, 11L-001,
11M-001, 11N-001, 11P-001, 11Q-001 or 11R-001 from the lavatory structure.
(b) Remove the screws 10-050, the nuts 10-070 and the section 10-010 from
the lavatory structure.
(c) Remove the screws 10-080, the sill 10-030 and the spacer 10-020 from the
floor pan.
TASK 25-41-58-000-807-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-071-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the screw 11-080 and the coat hook 11-090.
(c) Remove the screws 11-030, the washers 11-040 and the hinge 11-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11-020.
(e) Remove the screws 11-050 and the sections 11-060, 11-070.
(f) Remove the screws 11-030 and the lavatory simple door-latch 11-100 from the
single door assembly 11-001.
(h) Remove the screws 11-030 and the latch 11-150 from the single door assembly
11-001.
(j) Remove the screws 11-180 and the air outlets 11-170.
SUBTASK 25-41-58-010-071-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the screw 11-080 and the coat hook 11-090.
(c) Remove the screws 11-030, the washers 11-040 and the hinge 11-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11-020.
(e) Remove the screws 11-050 and the sections 11-060, 11-070.
(f) Remove the screws 11-030 and the lavatory simple door-latch 11-100 from the
single door assembly 11-001.
(h) Remove the screws 11-030 and the latch assembly 11-155 from the single
door assembly 11-001.
(j) Remove the screws 11-180 and the air outlets 11-170.
SUBTASK 25-41-58-010-071-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
FASTBOND 10
- Formica Bonding
Rigid Vinyl
(a) Remove the screw 11-080 and the coat hook 11-090.
(c) Remove the screws 11-030, the washers 11-040 and the hinge 11-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11-020.
(e) Remove the screws 11-050 and the sections 11-060, 11-070.
(f) Remove the screws 11-030 and the lavatory simple door-latch 11-100 from the
single door assembly 11-001.
(h) Remove the screws 11-030 and the latch assembly 11-155 from the single
door assembly 11-001.
(j) Remove the screws 11-180 and the air outlets 11-170.
SUBTASK 25-41-58-010-071-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
FASTBOND 10 -
Formica Bonding
Rigid Vinyl
(a) Remove the screw 11-080 and the coat hook 11-090.
(c) Remove the screws 11-030, the washers 11-040 and the hinge 11-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11-020.
(e) Remove the screws 11-050 and the sections 11-060, 11-070.
(f) Remove the screws 11-030 and the lavatory simple door-latch 11-100 from the
single door assembly 11-001.
(h) Remove the screws 11-030 and the latch 11-150 from the single door assembly
11-001.
(j) Remove the screws 11-180 and the air outlets 11-170.
TASK 25-41-58-000-807-B01
R225401884-000
41. Disassembly of the Door
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-073-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3157
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11A-080 and the coat hook 11A-090.
(c) Remove the screws 11A-030, the washers 11A-040 and the hinge 11A-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11A-020.
(e) Remove the screws 11A-050 and the sections 11A-060, 11A-070.
(f) Remove the screws 11A-030 and the lavatory simple door-latch 11A-100 from
the single door assembly 11A-001.
(h) Remove the screws 11A-030 and the latch 11A-150 from the single door
assembly 11A-001.
(j) Remove the screws 11A-180 and the air outlets 11A-170.
SUBTASK 25-41-58-010-073-B01
D2549020303600 D2549020308000
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3158
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11A-080 and the coat hook 11A-090.
(c) Remove the screws 11A-030, the washers 11A-040 and the hinge 11A-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11A-020.
(e) Remove the screws 11A-050 and the sections 11A-060, 11A-070.
(f) Remove the screws 11A-030 and the lavatory simple door-latch 11A-100 from
the single door assembly 11A-001.
(h) Remove the screws 11A-030 and the latch assembly 11A-155 from the single
door assembly 11A-001.
(j) Remove the screws 11A-180 and the air outlets 11A-170.
SUBTASK 25-41-58-010-073-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11A-080 and the coat hook 11A-090.
(c) Remove the screws 11A-030, the washers 11A-040 and the hinge 11A-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11A-020.
(e) Remove the screws 11A-050 and the sections 11A-060, 11A-070.
(f) Remove the screws 11A-030 and the lavatory simple door-latch 11A-100 from
the single door assembly 11A-001.
simple door-latch).
(g) Remove the screws 11A-030 and the lock assy 11A-105 from the single door
assembly 11A-001.
(j) Remove the screws 11A-030 and the latch assembly 11A-155 from the single
door assembly 11A-001.
(k) Remove the screws 11A-180 and the air outlets 11A-170.
SUBTASK 25-41-58-010-073-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11A-080 and the coat hook 11A-090.
(c) Remove the screws 11A-030, the washers 11A-040 and the hinge 11A-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11A-020.
(e) Remove the screws 11A-050 and the sections 11A-060, 11A-070.
(f) Remove the screws 11A-030 and the lavatory simple door-latch 11A-100 from
the single door assembly 11A-001.
simple door-latch).
(h) Remove the screws 11A-030 and the latch 11A-150 from the single door
assembly 11A-001.
(j) Remove the screws 11A-180 and the air outlets 11A-170.
TASK 25-41-58-000-807-C01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-074-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3161
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11B-080 and the coat hook 11B-090.
(c) Remove the screws 11B-030, the washers 11B-040 and the hinge 11B-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11B-020.
(e) Remove the screws 11B-050 and the sections 11B-060, 11B-070.
(f) Remove the screws 11B-030 and the lavatory simple door-latch 11B-100 from
the single door assembly 11B-001.
(h) Remove the screws 11B-030 and the latch assembly 11B-150 from the single
door assembly 11B-001.
(j) Remove the screws 11B-180 and the air outlets 11B-170.
SUBTASK 25-41-58-010-074-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3162
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11B-080 and the coat hook 11B-090.
(c) Remove the screws 11B-030, the washers 11B-040 and the hinge 11B-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11B-020.
(e) Remove the screws 11B-050 and the sections 11B-060, 11B-070.
(f) Remove the screws 11B-030 and the lavatory simple door-latch 11B-100 from
the single door assembly 11B-001.
(h) Remove the screws 11B-030 and the latch 11B-155 from the single door
assembly 11B-001.
(j) Remove the screws 11B-180 and the air outlets 11B-170.
SUBTASK 25-41-58-010-074-C01
D2549030706800 D2549030712000
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11B-080 and the coat hook 11B-090.
(c) Remove the screws 11B-030, the washers 11B-040 and the hinge 11B-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11B-020.
(e) Remove the screws 11B-050 and the sections 11B-060, 11B-070.
(f) Remove the screws 11B-030 and the lavatory simple door-latch 11B-100 from
the single door assembly 11B-001.
simple door-latch).
(h) Remove the screws 11B-030 and the latch assembly 11B-150 from the single
door assembly 11B-001.
(j) Remove the screws 11B-180 and the air outlets 11B-170.
TASK 25-41-58-000-807-D01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-075-A01
(1) Disassembly of the Door (11C-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the screw 11C-080 and the coat hook 11C-090.
(b) Remove the bumpers 11C-200 from the retainers 11C-190 and from the end
caps 11C-210.
(c) Remove the screws 11C-160, the washers 11C-170, the end caps 11C-210
and the retainers 11C-190.
(e) Remove the screws 11C-030, the washers 11C-040 and the hinge 11C-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11C-020.
(g) Remove the screws 11C-050 and the sections 11C-060, 11C-070.
(h) Remove the screws 11C-030 and the lavatory simple door-latch 11C-100 from
the single door assembly 11C-001.
(k) Remove the screws 11C-030 and the latch assembly 11C-110 from the single
door assembly 11C-001.
(l) Remove the screws 11C-230 and the air outlets 11C-240.
TASK 25-41-58-000-807-E01
A. General
– Cleaning
For Myanmar Airways (MMA) use only
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-076-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3165
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11D-080 and the coat hook 11D-090.
(c) Remove the screws 11D-030, the washers 11D-040 and the hinge 11D-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11D-020.
(e) Remove the screws 11D-050 and the sections 11D-060, 11D-070.
(f) Remove the screws 11D-030 and the lavatory simple door-latch 11D-100 from
the single door assembly 11D-001.
(h) Remove the screws 11D-030 and the latch 11D-150 from the single door
assembly 11D-001.
(j) Remove the screws 11D-170 and the air outlets 11D-160.
SUBTASK 25-41-58-010-076-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3166
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11D-080 and the coat hook 11D-090.
(c) Remove the screws 11D-030, the washers 11D-040 and the hinge 11D-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11D-020.
(e) Remove the screws 11D-050 and the sections 11D-060, 11D-070.
(f) Remove the screws 11D-030 and the lavatory simple door-latch 11D-100 from
the single door assembly 11D-001.
(h) Remove the screws 11D-030 and the latch assembly 11D-155 from the single
door assembly 11D-001.
(j) Remove the screws 11D-170 and the air outlets 11D-160.
SUBTASK 25-41-58-010-076-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding
Rigid Vinyl
(a) Remove the screw 11D-080 and the coat hook 11D-090.
(c) Remove the screws 11D-030, the washers 11D-040 and the hinge 11D-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11D-020.
(e) Remove the screws 11D-050 and the sections 11D-060, 11D-070.
(f) Remove the screws 11D-030 and the lavatory simple door-latch 11D-100 from
the single door assembly 11D-001.
simple door-latch).
(h) Remove the screws 11D-030 and the latch assembly 11D-155 from the single
door assembly 11D-001.
(j) Remove the screws 11D-170 and the air outlets 11D-160.
TASK 25-41-58-000-807-F01
A. General
– Cleaning
– Visual Inspection
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-077-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3168
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11E-080 and the coat hook 11E-090.
(c) Remove the screws 11E-030, the washers 11E-040 and the hinge 11E-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11E-020.
(e) Remove the screws 11E-050 and the sections 11E-060, 11E-070.
(f) Remove the screws 11E-030 and the lavatory simple door-latch 11E-100 from
the single door assembly 11E-001.
(h) Remove the screws 11E-030 and the latch assembly 11E-155 from the single
door assembly 11E-001.
(j) Remove the screws 11E-180 and the air outlets 11E-170.
SUBTASK 25-41-58-010-077-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3169
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11E-080 and the coat hook 11E-090.
(c) Remove the screws 11E-030, the washers 11E-040 and the hinge 11E-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11E-020.
(e) Remove the screws 11E-050 and the sections 11E-060, 11E-070.
(f) Remove the screws 11E-030 and the lavatory simple door-latch 11E-100 from
the single door assembly 11E-001.
(h) Remove the screws 11E-030 and the latch 11E-150 from the single door
assembly 11E-001.
(j) Remove the screws 11E-180 and the air outlets 11E-170.
SUBTASK 25-41-58-010-077-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11E-080 and the coat hook 11E-090.
(c) Remove the screws 11E-030, the washers 11E-040 and the hinge 11E-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11E-020.
(e) Remove the screws 11E-050 and the sections 11E-060, 11E-070.
(f) Remove the screws 11E-030 and the lavatory simple door-latch 11E-100 from
the single door assembly 11E-001.
simple door-latch).
(h) Remove the screws 11E-030 and the latch 11E-150 from the single door
assembly 11E-001.
(j) Remove the screws 11E-180 and the air outlets 11E-170.
SUBTASK 25-41-58-010-077-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11E-080 and the coat hook 11E-090.
(c) Remove the screws 11E-030, the washers 11E-040 and the hinge 11E-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11E-020.
(e) Remove the screws 11E-050 and the sections 11E-060, 11E-070.
(f) Remove the screws 11E-030 and the lavatory simple door-latch 11E-100 from
the single door assembly 11E-001.
(h) Remove the screws 11E-030 and the latch assembly 11E-155 from the single
door assembly 11E-001.
(j) Remove the screws 11E-180 and the air outlets 11E-170.
TASK 25-41-58-000-807-G01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-078-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
PART
NAME
(a) Remove the screw 11F-080 and the coat hook 11F-090.
(c) Remove the screws 11F-030, the washers 11F-040 and the hinge 11F-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11F-020.
(e) Remove the screws 11F-050 and the sections 11F-060, 11F-070.
(f) Remove the screws 11F-030 and the lavatory simple door-latch 11F-100 from
the single door assembly 11F-001.
simple door-latch).
(h) Remove the screws 11F-030 and the latch assembly 11F-150 from the single
door assembly 11F-001.
(j) Remove the screws 11F-180 and the air outlets 11F-170.
SUBTASK 25-41-58-010-078-B01
D2549020900800
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3173
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11F-080 and the coat hook 11F-090.
(c) Remove the screws 11F-030, the washers 11F-040 and the hinge 11F-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11F-020.
(e) Remove the screws 11F-050 and the sections 11F-060, 11F-070.
(f) Remove the screws 11F-030 and the lavatory simple door-latch 11F-100 from
the single door assembly 11F-001.
(h) Remove the screws 11F-030 and the latch 11F-155 from the single door
assembly 11F-001.
(j) Remove the screws 11F-180 and the air outlets 11F-170.
SUBTASK 25-41-58-010-078-C01
D2549010410400
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11F-080 and the coat hook 11F-090.
(c) Remove the screws 11F-030, the washers 11F-040 and the hinge 11F-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11F-020.
(e) Remove the screws 11F-050 and the sections 11F-060, 11F-070.
(f) Remove the screws 11F-030 and the lavatory simple door-latch 11F-100 from
the single door assembly 11F-001.
simple door-latch).
(h) Remove the screws 11F-030 and the latch assembly 11F-150 from the single
door assembly 11F-001.
(j) Remove the screws 11F-180 and the air outlets 11F-170.
SUBTASK 25-41-58-010-078-D01
D2549010410600 D2549020901000
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11F-080 and the coat hook 11F-090.
(c) Remove the screws 11F-030, the washers 11F-040 and the hinge 11F-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11F-020.
(e) Remove the screws 11F-050 and the sections 11F-060, 11F-070.
(f) Remove the screws 11F-030 and the lavatory simple door-latch 11F-100 from
the single door assembly 11F-001.
simple door-latch).
(h) Remove the screws 11F-030 and the latch 11F-155 from the single door
assembly 11F-001.
(j) Remove the screws 11F-180 and the air outlets 11F-170.
TASK 25-41-58-000-807-H01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-079-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3176
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11G-080 and the coat hook 11G-090.
(c) Remove the screws 11G-030, the washers 11G-040 and the hinge 11G-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11G-020.
(e) Remove the screws 11G-050 and the sections 11G-060, 11G-070.
(f) Remove the screws 11G-030 and the lavatory simple door-latch 11G-100 from
the single door assembly 11G-001.
(h) Remove the screws 11G-030 and the latch 11G-155 from the single door
assembly 11G-001.
(j) Remove the screws 11G-180 and the air outlets 11G-170.
SUBTASK 25-41-58-010-079-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3177
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11G-080 and the coat hook 11G-090.
(c) Remove the screws 11G-030, the washers 11G-040 and the hinge 11G-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11G-020.
(e) Remove the screws 11G-050 and the sections 11G-060, 11G-070.
(f) Remove the screws 11G-030 and the lavatory simple door-latch 11G-100 from
the single door assembly 11G-001.
(h) Remove the screws 11G-030 and the latch assembly 11G-150 from the single
door assembly 11G-001.
(j) Remove the screws 11G-180 and the air outlets 11G-170.
SUBTASK 25-41-58-010-079-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11G-080 and the coat hook 11G-090.
(c) Remove the screws 11G-030, the washers 11G-040 and the hinge 11G-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11G-020.
(e) Remove the screws 11G-050 and the sections 11G-060, 11G-070.
(f) Remove the screws 11G-030 and the lavatory simple door-latch 11G-100 from
the single door assembly 11G-001.
simple door-latch).
(h) Remove the screws 11G-030 and the latch assembly 11G-150 from the single
door assembly 11G-001.
(j) Remove the screws 11G-180 and the air outlets 11G-170.
SUBTASK 25-41-58-010-079-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11G-080 and the coat hook 11G-090.
(c) Remove the screws 11G-030, the washers 11G-040 and the hinge 11G-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11G-020.
(e) Remove the screws 11G-050 and the sections 11G-060, 11G-070.
(f) Remove the screws 11G-030 and the lavatory simple door-latch 11G-100 from
the single door assembly 11G-001.
simple door-latch).
(h) Remove the screws 11G-030 and the latch 11G-155 from the single door
assembly 11G-001.
(j) Remove the screws 11G-180 and the air outlets 11G-170.
TASK 25-41-58-000-807-J01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-080-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding
Rigid Vinyl
Table 3180
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11H-080 and the coat hook 11H-090.
(c) Remove the screws 11H-030, the washers 11H-040 and the hinge 11H-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11H-020.
(e) Remove the screws 11H-050 and the sections 11H-060, 11H-070.
(f) Remove the screws 11H-030 and the lavatory simple door-latch 11H-100 from
the single door assembly 11H-001.
(h) Remove the screws 11H-030 and the latch assembly 11H-150 from the single
door assembly 11H-001.
(j) Remove the screws 11H-180 and the air outlets 11H-170.
SUBTASK 25-41-58-010-080-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3181
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11H-080 and the coat hook 11H-090.
(c) Remove the screws 11H-030, the washers 11H-040 and the hinge 11H-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11H-020.
(e) Remove the screws 11H-050 and the sections 11H-060, 11H-070.
(f) Remove the screws 11H-030 and the lavatory simple door-latch 11H-100 from
the single door assembly 11H-001.
(h) Remove the screws 11H-030 and the latch 11H-155 from the single door
assembly 11H-001.
(j) Remove the screws 11H-180 and the air outlets 11H-170.
TASK 25-41-58-000-807-K01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-081-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
PART
NAME
(a) Remove the screw 11J-080 and the coat hook 11J-090.
(b) Remove the bumper 11J-200 from the retainer 11J-190 and from the end caps
11J-210.
(c) Remove the screws 11J-160, the washers 11J-170, the end caps 11J-210 and
the retainer 11J-190.
(e) Remove the screws 11J-030, the washers 11J-040 and the hinge 11J-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11J-020.
For Myanmar Airways (MMA) use only
(g) Remove the screws 11J-050 and the sections 11J-060, 11J-070.
(h) Remove the screws 11J-030 and the lavatory simple door-latch 11J-100 from
the single door assembly 11J-001.
(k) Remove the screws 11J-030 and the latch 11J-110 from the single door
assembly 11J-001.
(l) Remove the screws 11J-230 and the air outlets 11J-240.
SUBTASK 25-41-58-010-081-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3183
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11J-080 and the coat hook 11J-090.
(b) Remove the bumper 11J-200 from the retainer 11J-190 and from the end caps
11J-210.
(c) Remove the screws 11J-160, the washers 11J-170, the end caps 11J-210 and
the retainer 11J-190.
(e) Remove the screws 11J-030, the washers 11J-040 and the hinge 11J-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11J-020.
(g) Remove the screws 11J-050 and the sections 11J-060, 11J-070.
(h) Remove the screws 11J-030 and the lavatory simple door-latch 11J-100 from
the single door assembly 11J-001.
simple door-latch).
(k) Remove the screws 11J-030 and the latch assembly 11J-115 from the single
door assembly 11J-001.
(l) Remove the screws 11J-230 and the air outlets 11J-240.
TASK 25-41-58-000-807-L01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-082-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3184
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11K-080 and the coat hook 11K-090.
(c) Remove the screws 11K-030, the washers 11K-040 and the hinge 11K-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11K-020.
(e) Remove the screws 11K-050 and the sections 11K-060, 11K-070.
(f) Remove the screws 11K-030 and the lavatory simple door-latch 11K-100 from
the single door assembly 11K-001.
(h) Remove the screws 11K-030 and the latch assembly 11K-150 from the single
door assembly 11K-001.
(j) Remove the screws 11K-180 and the air outlets 11K-170.
SUBTASK 25-41-58-010-082-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3185
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11K-080 and the coat hook 11K-090.
(c) Remove the screws 11K-030, the washers 11K-040 and the hinge 11K-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11K-020.
(e) Remove the screws 11K-050 and the sections 11K-060, 11K-070.
(f) Remove the screws 11K-030 and the lavatory simple door-latch 11K-100 from
the single door assembly 11K-001.
(h) Remove the screws 11K-030 and the latch 11K-155 from the single door
assembly 11K-001.
(j) Remove the screws 11K-180 and the air outlets 11K-170.
SUBTASK 25-41-58-010-082-C01
D2549020907400 D2549020908600
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11K-080 and the coat hook 11K-090.
(c) Remove the screws 11K-030, the washers 11K-040 and the hinge 11K-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11K-020.
(e) Remove the screws 11K-050 and the sections 11K-060, 11K-070.
(f) Remove the screws 11K-030 and the lavatory simple door-latch 11K-100 from
the single door assembly 11K-001.
simple door-latch).
(h) Remove the screws 11K-030 and the latch 11K-155 from the single door
assembly 11K-001.
(j) Remove the screws 11K-180 and the air outlets 11K-170.
SUBTASK 25-41-58-010-082-D01
D2549020907800 D2549020909400
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11K-080 and the coat hook 11K-090.
(c) Remove the screws 11K-030, the washers 11K-040 and the hinge 11K-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11K-020.
(e) Remove the screws 11K-050 and the sections 11K-060, 11K-070.
(f) Remove the screws 11K-030 and the lavatory simple door-latch 11K-100 from
the single door assembly 11K-001.
simple door-latch).
(h) Remove the screws 11K-030 and the latch assembly 11K-150 from the single
door assembly 11K-001.
(j) Remove the screws 11K-180 and the air outlets 11K-170.
TASK 25-41-58-000-807-M01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-083-A01
D2549010413800
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3188
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11L-080 and the coat hook 11L-090.
(c) Remove the screws 11L-030, the washers 11L-040 and the hinge 11L-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11L-020.
(e) Remove the screws 11L-050 and the sections 11L-060, 11L-070.
(f) Remove the screws 11L-030 and the lavatory simple door-latch 11L-100 from
the single door assembly 11L-001.
(h) Remove the screws 11L-180 and the air outlets 11L-170.
SUBTASK 25-41-58-010-083-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3189
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11L-080 and the coat hook 11L-090.
(c) Remove the screws 11L-030, the washers 11L-040 and the hinge 11L-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11L-020.
(e) Remove the screws 11L-050 and the sections 11L-060, 11L-070.
(f) Remove the screws 11L-030 and the lavatory simple door-latch 11L-100 from
the single door assembly 11L-001.
(h) Remove the screws 11L-030 and the latch 11L-155 from the single door
assembly 11L-001.
(j) Remove the screws 11L-180 and the air outlets 11L-170.
SUBTASK 25-41-58-010-083-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11L-080 and the coat hook 11L-090.
(c) Remove the screws 11L-030, the washers 11L-040 and the hinge 11L-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11L-020.
(e) Remove the screws 11L-050 and the sections 11L-060, 11L-070.
(f) Remove the screws 11L-030 and the lavatory simple door-latch 11L-100 from
the single door assembly 11L-001.
simple door-latch).
(g) Remove the screws 11L-030 and the lock assy 11L-105 from the single door
assembly 11L-001.
(j) Remove the screws 11L-030 and the latch assembly 11L-150 from the single
door assembly 11L-001.
(k) Remove the screws 11L-180 and the air outlets 11L-170.
SUBTASK 25-41-58-010-083-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11L-080 and the coat hook 11L-090.
(c) Remove the screws 11L-030, the washers 11L-040 and the hinge 11L-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11L-020.
(e) Remove the screws 11L-050 and the sections 11L-060, 11L-070.
(f) Remove the screws 11L-030 and the lavatory simple door-latch 11L-100 from
the single door assembly 11L-001.
simple door-latch).
(h) Remove the screws 11L-030 and the latch 11L-155 from the single door
assembly 11L-001.
(j) Remove the screws 11L-180 and the air outlets 11L-170.
TASK 25-41-58-000-807-N01
A. General
– Cleaning
– Visual Inspection
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-084-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3192
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11M-080 and the coat hook 11M-090.
(c) Remove the screws 11M-030, the washers 11M-040 and the hinge 11M-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11M-020.
(e) Remove the screws 11M-050 and the sections 11M-060, 11M-070.
(f) Remove the screws 11M-030 and the lavatory simple door-latch 11M-100 from
the single door assembly 11M-001.
(h) Remove the screws 11M-030 and the latch 11M-150 from the single door
assembly 11M-001.
(j) Remove the screws 11M-180 and the air outlets 11M-170.
SUBTASK 25-41-58-010-084-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding
Rigid Vinyl
(a) Remove the screw 11M-080 and the coat hook 11M-090.
(c) Remove the screws 11M-030, the washers 11M-040 and the hinge 11M-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11M-020.
(e) Remove the screws 11M-050 and the sections 11M-060, 11M-070.
(f) Remove the screws 11M-030 and the lavatory simple door-latch 11M-100 from
the single door assembly 11M-001.
simple door-latch).
(h) Remove the screws 11M-030 and the latch 11M-150 from the single door
assembly 11M-001.
(j) Remove the screws 11M-180 and the air outlets 11M-170.
SUBTASK 25-41-58-010-084-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11M-080 and the coat hook 11M-090.
(c) Remove the screws 11M-030, the washers 11M-040 and the hinge 11M-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11M-020.
(e) Remove the screws 11M-050 and the sections 11M-060, 11M-070.
(f) Remove the screws 11M-030 and the lavatory simple door-latch 11M-100 from
the single door assembly 11M-001.
simple door-latch).
(h) Remove the screws 11M-030 and the latch assembly 11M-155 from the single
door assembly 11M-001.
(j) Remove the screws 11M-180 and the air outlets 11M-170.
TASK 25-41-58-000-807-P01
A. General
– Cleaning
For Myanmar Airways (MMA) use only
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-085-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3195
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11N-080 and the coat hook 11N-090.
(c) Remove the screws 11N-030, the washers 11N-040 and the hinge 11N-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11N-020.
(e) Remove the screws 11N-050 and the sections 11N-060, 11N-070.
(f) Remove the screws 11N-030 and the lavatory simple door-latch 11N-100 from
the single door assembly 11N-001.
(h) Remove the screws 11N-030 and the latch assembly 11N-150 from the single
door assembly 11N-001.
(j) Remove the screws 11N-180 and the air outlets 11N-170.
SUBTASK 25-41-58-010-085-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3196
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11N-080 and the coat hook 11N-090.
(c) Remove the screws 11N-030, the washers 11N-040 and the hinge 11N-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11N-020.
(e) Remove the screws 11N-050 and the sections 11N-060, 11N-070.
(f) Remove the screws 11N-030 and the lavatory simple door-latch 11N-100 from
the single door assembly 11N-001.
(h) Remove the screws 11N-030 and the latch 11N-155 from the single door
assembly 11N-001.
(j) Remove the screws 11N-180 and the air outlets 11N-170.
SUBTASK 25-41-58-010-085-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11N-080 and the coat hook 11N-090.
(c) Remove the screws 11N-030, the washers 11N-040 and the hinge 11N-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11N-020.
(e) Remove the screws 11N-050 and the sections 11N-060, 11N-070.
(f) Remove the screws 11N-030 and the lavatory simple door-latch 11N-100 from
the single door assembly 11N-001.
simple door-latch).
(h) Remove the screws 11N-030 and the latch 11N-155 from the single door
assembly 11N-001.
(j) Remove the screws 11N-180 and the air outlets 11N-170.
TASK 25-41-58-000-807-Q01
A. General
– Cleaning
For Myanmar Airways (MMA) use only
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-086-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3198
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11P-080 and the coat hook 11P-090.
(c) Remove the screws 11P-030, the washers 11P-040 and the hinge 11P-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11P-020.
(e) Remove the screws 11P-050 and the sections 11P-060, 11P-070.
(f) Remove the screws 11P-030 and the lavatory simple door-latch 11P-100 from
the single door assembly 11P-001.
(h) Remove the screws 11P-030 and the latch assembly 11P-150 from the single
door assembly 11P-001.
(j) Remove the screws 11P-180 and the air outlets 11P-170.
SUBTASK 25-41-58-010-086-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3199
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11P-080 and the coat hook 11P-090.
(c) Remove the screws 11P-030, the washers 11P-040 and the hinge 11P-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11P-020.
(e) Remove the screws 11P-050 and the sections 11P-060, 11P-070.
(f) Remove the screws 11P-030 and the lavatory simple door-latch 11P-100 from
the single door assembly 11P-001.
(h) Remove the screws 11P-030 and the latch 11P-155 from the single door
assembly 11P-001.
(j) Remove the screws 11P-180 and the air outlets 11P-170.
SUBTASK 25-41-58-010-086-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
(a) Remove the screw 11P-080 and the coat hook 11P-090.
(c) Remove the screws 11P-030, the washers 11P-040 and the hinge 11P-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11P-020.
(e) Remove the screws 11P-050 and the sections 11P-060, 11P-070.
(f) Remove the screws 11P-030 and the lavatory simple door-latch 11P-100 from
the single door assembly 11P-001.
simple door-latch).
(h) Remove the screws 11P-030 and the latch assembly 11P-150 from the single
door assembly 11P-001.
(j) Remove the screws 11P-180 and the air outlets 11P-170.
TASK 25-41-58-000-807-R01
D2549030811600
55. Disassembly of the Door
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-087-A01
(1) Disassembly of the Door (11Q-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the screw 11Q-080 and the coat hook 11Q-090.
(b) Remove the bumpers 11Q-200 from the retainers 11Q-190 and from the end
caps 11Q-210.
(c) Remove the screws 11Q-160, the washers 11Q-170, the end caps 11Q-210
and the retainers 11Q-190.
(e) Remove the screws 11Q-030, the washers 11Q-040 and the hinge 11Q-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11Q-020.
(g) Remove the screws 11Q-050 and the sections 11Q-060, 11Q-070.
(h) Remove the screws 11Q-030 and the lavatory simple door-latch 11Q-100 from
the single door assembly 11Q-001.
(k) Remove the screws 11Q-030 and the latch assembly 11Q-110 from the single
door assembly 11Q-001.
(l) Remove the screws 11Q-230 and the air outlets 11Q-240.
TASK 25-41-58-000-807-S01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-088-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3202
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11R-080 and the coat hook 11R-090.
(c) Remove the screws 11R-030, the washers 11R-040 and the hinge 11R-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11R-020.
(e) Remove the screws 11R-050 and the sections 11R-060, 11R-070.
(f) Remove the screws 11R-030 and the lavatory simple door-latch 11R-100 from
the single door assembly 11R-001.
(h) Remove the screws 11R-030 and the latch 11R-150 from the single door
assembly 11R-001.
(j) Remove the screws 11R-180 and the air outlets 11R-170.
SUBTASK 25-41-58-010-088-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding Rigid
Vinyl
Table 3203
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screw 11R-080 and the coat hook 11R-090.
(c) Remove the screws 11R-030, the washers 11R-040 and the hinge 11R-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11R-020.
(e) Remove the screws 11R-050 and the sections 11R-060, 11R-070.
(f) Remove the screws 11R-030 and the lavatory simple door-latch 11R-100 from
the single door assembly 11R-001.
(h) Remove the screws 11R-030 and the latch assembly 11R-155 from the single
door assembly 11R-001.
(j) Remove the screws 11R-180 and the air outlets 11R-170.
SUBTASK 25-41-58-010-088-C01
D2549010301200 D2549010414600
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding
Rigid Vinyl
(a) Remove the screw 11R-080 and the coat hook 11R-090.
(c) Remove the screws 11R-030, the washers 11R-040 and the hinge 11R-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11R-020.
(e) Remove the screws 11R-050 and the sections 11R-060, 11R-070.
(f) Remove the screws 11R-030 and the lavatory simple door-latch 11R-100 from
the single door assembly 11R-001.
simple door-latch).
(h) Remove the screws 11R-030 and the latch assembly 11R-155 from the single
door assembly 11R-001.
(j) Remove the screws 11R-180 and the air outlets 11R-170.
SUBTASK 25-41-58-010-088-D01
D2549026005600 R225401860-004
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-801-
A01
Material
No. 08-553
FASTBOND
10 - Formica
Bonding
Rigid Vinyl
(a) Remove the screw 11R-080 and the coat hook 11R-090.
(c) Remove the screws 11R-030, the washers 11R-040 and the hinge 11R-010.
NOTE: If necessary use a hot air blower to heat up the Material No.
08-007 Sealant, High Temperature to remove the setscrews
11R-020.
(e) Remove the screws 11R-050 and the sections 11R-060, 11R-070.
(f) Remove the screws 11R-030 and the lavatory simple door-latch 11R-100 from
the single door assembly 11R-001.
For Myanmar Airways (MMA) use only
(h) Remove the screws 11R-030 and the latch 11R-150 from the single door
assembly 11R-001.
(j) Remove the screws 11R-180 and the air outlets 11R-170.
TASK 25-41-58-000-808-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-041-A01
(1) Removal of the Toilet Unit and of the Toilet Shroud (12-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Material No.
08-025 Two
Component
Polyurethane
Adhesive
(a) Remove the screws 12-070, the nuts 12-080 and the toilet shroud assembly
12-010 from the lavatory structure.
(b) Remove the nuts 12-100, the gaskets 12-110 and the toilet seat assembly
12-090 from the toilet shroud assembly 12-010.
1 Remove the fasteners 12-120 or the unpainted fasteners 12-130 and the
toilet cover assembly 12-140 from the toilet seat assembly 12-170.
(d) Remove the screws 12-250, the washers 12-260, the nuts 12-270 and the
support bracket 12-220 from the lavatory structure.
(e) Remove the screws 12-240, the washers 12-260 and the support bracket
12-230 from the lavatory structure.
(f) Remove the ground cable from the toilet assembly 12-310.
(g) Remove the bolts 12-280, the lock washers 12-290, the washers 12-300 and
the toilet assembly 12-310 from the floor pan.
TASK 25-41-58-000-808-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-042-A01
(1) Removal of the Toilet Unit and of the Toilet Shroud (12A-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
INSTALLED PARTS
(a) Remove the screws 12A-070, the nuts 12A-080 and the toilet shroud assembly
12A-010 from the lavatory structure.
(b) Remove the nuts 12A-210, 12A-240 and the gaskets 12A-200, 12A-230 from
the damper assemblies 12A-190, 12A-220.
(c) Remove the toilet seat assembly 12A-090 from the toilet shroud assembly
12A-010.
1 Remove the damper assemblies 12A-190, 12A-220 and the toilet cover
assembly 12A-100 from the toilet seat assembly 12A-140.
(e) Remove the screws 12A-270, the washers 12A-290 and the support bracket
12A-250 from the lavatory structure.
(f) Remove the screws 12A-280, the washers 12A-290, the nuts 12A-340 and the
support bracket 12A-260 from the lavatory structure.
(g) Remove the ground cable from the toilet assembly 12A-330.
(h) Remove the bolts 12A-300, the lock washers 12A-310, the washers 12A-320
and the toilet assembly 12A-330 from the floor pan.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-808-C01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-043-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Table 3208
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screws 12B-070, the nuts 12B-080 and the toilet shroud assembly
12B-010 from the lavatory structure.
(b) Remove the nuts 12B-100, the gaskets 12B-110 and the toilet seat assembly
12B-090 from the toilet shroud assembly 12B-010.
(d) Remove the screws 12B-250, the washers 12B-260, the nuts 12B-270 and the
support bracket 12B-220 from the lavatory structure.
(e) Remove the screws 12B-240, the washers 12B-260 and the support bracket
12B-230 from the lavatory structure.
(f) Remove the ground cable from the toilet assembly 12B-310.
(g) Remove the bolts 12B-280, the lock washers 12B-290, the washers 12B-300
and the toilet assembly 12B-310 from the floor pan.
SUBTASK 25-41-58-000-004-A01
(1) Removal of the Toilet Unit and of the Toilet Shroud (12A-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Rubber
(a) Remove the screws 12B-070, the nuts 12B-080 and the toilet shroud assembly
12B-010 from the lavatory structure.
(b) Remove the nuts 12B-100, the gaskets 12B-110 and the toilet seat assembly
12B-090 from the toilet shroud assembly 12B-010.
(d) Remove the screws 12B-250, the washers 12B-260, the nuts 12B-270 and the
support bracket 12B-220 from the lavatory structure.
(e) Remove the screws 12B-240, the washers 12B-260 and the support bracket
12B-230 from the lavatory structure.
(f) Remove the ground cable from the toilet assembly 12B-310.
(g) Remove the bolts 12B-280, the lock washers 12B-290, the washers 12B-300
and the toilet assembly 12B-310 from the floor pan.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-808-D01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-010-044-A01
(1) Removal of the Toilet Unit and of the Toilet Shroud (12C-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
INSTALLED PARTS
(a) Remove the screws 12C-070, the nuts 12C-080 and the toilet shroud assembly
12C-010 from the lavatory structure.
(b) Remove the nuts 12C-100, the gaskets 12C-110 and the toilet seat assembly
12C-090 from the toilet shroud assembly 12C-010.
(d) Remove the screws 12C-250, the washers 12C-260, the nuts 12C-270 and the
support bracket 12C-220 from the lavatory structure.
(e) Remove the screws 12C-240, the washers 12C-260 and the support bracket
12C-230 from the lavatory structure.
(f) Remove the ground cable from the toilet assembly 12C-310.
(g) Remove the bolts 12C-280, the lock washers 12C-290, the washers 12C-300
and the toilet assembly 12C-310 from the floor pan.
TASK 25-41-58-000-809-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-095-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the screws 13-190, 13-210 and the washers 13-200, 13-220, 13-230
from the angles 13-090, 13-100, 13-120 and from the lavatory structure.
(b) Remove the screws 13-160, the washers 13-140, the nuts 13-170 and the
angles 13-150 from the floor-panel end strip 13-040.
(c) Remove the screws 13-110 and the angles 13-090, 13-100 from the floor panel
assembly 13-030.
(d) Remove the screws 13-130, the washers 13-140 and the angle 13-120 from
the floor panel assembly 13-030.
(e) Remove the screws 13-180 and the floor panel assembly 13-030 from the
lavatory structure.
1 Remove the screws 13-050 and the floor-panel end strip 13-040.
SUBTASK 25-41-58-000-095-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the screws 13-190, 13-210, the washers 13-200, 13-220, 13-230
and the floor pan 13-010 from the angles 13-090, 13-100, 13-120 and from
the lavatory structure.
(b) Remove the screws 13-110 and the angles 13-090, 13-100 from the floor panel
assembly 13-030.
(c) Remove the screws 13-130, the washers 13-141 and the angle 13-120 from
the floor panel assembly 13-030.
(d) Remove the screws 13-180 and the floor panel assembly 13-030 from the
lavatory structure.
TASK 25-41-58-000-809-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-096-A01
(1) Removal of the Floor Pan (13A-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. Scotch
4930-Adhesive
Tape
(a) Remove the screws 13A-210, 13A-230, the washers 13A-220, 13A-240,
13A-250 and the floor pan assembly 13A-010 from the angles 13A-110,
13A-120, 13A-140 and from the lavatory structure.
(b) Remove the screws 13A-180, the washers 13A-160, the nuts 13A-190 and the
angles 13A-170 from the floor-panel end strip 13A-060.
(c) Remove the screws 13A-130 and the angles 13A-110, 13A-120 from the floor
panel assembly 13A-050.
(d) Remove the screws 13A-150, the washers 13A-160 and the angle 13A-140
from the floor panel assembly 13A-050.
(e) Remove the screws 13A-200 and the floor panel assembly 13A-050 from the
lavatory structure.
1 Remove the sealant 13A-043, the adhesive tape 13A-045 and the
non-textile flooring 13A-040 from the floor pan 13A-020.
1 Remove the screws 13A-070 and the floor-panel end strip 13A-060.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-809-C01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-097-A01
(1) Removal of the Floor Pan (13B-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. Scotch
4930-Adhesive
Tape
(a) Remove the screws 13B-210, 13B-230, the washers 13B-220, 13B-240,
13B-250 and the floor pan assembly 13B-010 from the angles 13B-110,
13B-120, 13B-140 and from the lavatory structure.
(b) Remove the screws 13B-180, the washers 13B-160, the nuts 13B-190 and the
angles 13B-170 from the floor-panel end strip 13B-060.
(c) Remove the screws 13B-130 and the angles 13B-110, 13B-120 from the floor
panel assembly 13B-050.
(d) Remove the screws 13B-150, the washers 13B-160 and the angle 13B-140
from the floor panel assembly 13B-050.
(e) Remove the screws 13B-200 and the floor panel assembly 13B-050 from the
lavatory structure.
1 Remove the screws 13B-070 and the floor-panel end strip 13B-060.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-809-D01
A. General
For Myanmar Airways (MMA) use only
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-098-A01
(1) Removal of the Floor Pan (13C-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material
No. Scotch
4930-Adhesive
Tape
(a) Remove the screws 13C-210, 13C-230, the washers 13C-220, 13C-240,
13C-250 and the floor pan assembly 13C-010 from the angles 13C-110,
13C-120, 13C-140 and from the lavatory structure.
(b) Remove the screws 13C-180, the washers 13C-160, the nuts 13C-190 and the
angles 13C-170 from the floor-panel end strip 13C-060.
(c) Remove the screws 13C-130 and the angles 13C-110, 13C-120 from the floor
panel assembly 13C-050.
(d) Remove the screws 13C-150, the washers 13C-160 and the angle 13C-140
from the floor panel assembly 13C-050.
(e) Remove the screws 13C-200 and the floor panel assembly 13C-050 from the
lavatory structure.
1 Remove the screws 13C-070 and the floor-panel end strip 13C-060.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-809-E01
A. General
– Cleaning
– Visual Inspection
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-099-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
PART NAME
NAME
(a) Remove the screws 13D-210, 13D-230, the washers 13D-220, 13D-240,
13D-250 and the floor pan assembly 13D-010 from the angles 13D-110,
13D-120, 13D-140 and from the lavatory structure.
(b) Remove the screws 13D-180, the washers 13D-160, the nuts 13D-190 and the
angles 13D-170 from the floor-panel end strip 13D-060.
(c) Remove the screws 13D-130 and the angles 13D-110, 13D-120 from the floor
panel assembly 13D-050.
(d) Remove the screws 13D-150, the washers 13D-160 and the angle 13D-140
from the floor panel assembly 13D-050.
(e) Remove the screws 13D-200 and the floor panel assembly 13D-050 from the
lavatory structure.
1 Remove the screws 13D-070 and the floor-panel end strip 13D-060.
SUBTASK 25-41-58-000-099-B01
D2549030712000
For Myanmar Airways (MMA) use only
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the screws 13D-210, 13D-230, the washers 13D-220, 13D-240,
13D-250 and the floor pan assembly 13D-010 from the angles 13D-110,
13D-120, 13D-140 and from the lavatory structure.
(b) Remove the screws 13D-180, the washers 13D-160, the nuts 13D-190 and the
angles 13D-170 from the floor-panel end strip 13D-060.
(c) Remove the screws 13D-130 and the angles 13D-110, 13D-120 from the floor
panel assembly 13D-050.
(d) Remove the screws 13D-150, the washers 13D-160 and the angle 13D-140
from the floor panel assembly 13D-050.
(e) Remove the screws 13D-200 and the floor panel assembly 13D-050 from the
lavatory structure.
1 Remove the screws 13D-070 and the floor-panel end strip 13D-060.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-809-F01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-100-A01
(1) Removal of the Floor Pan (13E-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material No.
Scotch Grip
847
(a) Remove the screws 13E-170, 13E-190, the washers 13E-180, 13E-200,
13E-210 and the floor pan assembly 13E-010 from the angles 13E-110,
13E-120, 13E-140 and from the lavatory structure.
1 Remove the sealant 13E-043, the adhesive tape 13E-045 and the
non-textile flooring 13E-0640 from the floor pan 13E-20.
(c) Remove the screws 13E-130 and the angles 13E-110, 13E-120 from the floor
panel assembly 13E-050.
(d) Remove the screws 13E-150, the washers 13E-100 and the angle 13E-140
from the floor panel assembly 13E-050.
(e) Remove the screws 13E-160 and the floor panel assembly 13E-050 from the
lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-809-G01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-101-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Material No.
Scotch Grip
847
(a) Remove the screws 13F-180, 13F-200, the washers 13F-190, 13F-210,
13F-220 and the floor pan assembly 13F-010 from the angles 13F-110,
13F-120, 13F-140 and from the lavatory structure.
(b) Remove the screws 13F-130 and the angles 13F-110, 13F-120 from the floor
panel assembly 13F-050.
(c) Remove the screws 13F-150, the washers 13F-100 and the angle 13F-140
from the floor panel assembly 13F-050.
(d) Remove the screws 13F-170 and the floor panel assembly 13F-050 from the
lavatory structure.
(e) Remove the sealant 13F-042, the adhesive tape 13F-045 and the non-textile
flooring 13F-040 from the floor pan 13F-020.
SUBTASK 25-41-58-000-101-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
PART NAME
NAME
(a) Remove the screws 13F-180, 13F-200, the washers 13F-190, 13F-210,
13F-220 and the floor pan assembly 13F-010 from the angles 13F-110,
13F-120, 13F-140 and from the lavatory structure.
(b) Remove the screws 13F-130 and the angles 13F-110, 13F-120 from the floor
panel assembly 13F-050.
(c) Remove the screws 13F-150, the washers 13F-100 and the angle 13F-140
from the floor panel assembly 13F-050.
(d) Remove the screws 13F-170 and the floor panel assembly 13F-050 from the
lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-809-H01
A. General
– Cleaning
For Myanmar Airways (MMA) use only
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-102-A01
(1) Removal of the Floor Pan (13G-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the screws 13G-180, 13G-200, the washers 13G-190, 13G-210,
13G-220 and the floor pan assembly 13G-010 from the angles 13G-110,
13G-120, 13G-140 and from the lavatory structure.
(b) Remove the screws 13G-130 and the angles 13G-110, 13G-120 from the floor
panel assembly 13G-050.
(c) Remove the screws 13G-150, the washers 13G-100 and the angle 13G-140
from the floor panel assembly 13G-050.
(d) Remove the screws 13G-170 and the floor panel assembly 13G-050 from
the lavatory structure.
(e) Remove the sealant 13G-042, the adhesive tape 13G-043 and the non-textile
flooring 13G-040 from the floor pan 13G-020.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-809-J01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-103-A01
(1) Removal of the Floor Pan (13H-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material No.
Scotch Grip
847
(a) Remove the screws 13H-180, 13H-200, the washers 13H-190, 13H-210,
13H-220 and the floor pan assembly 13H-010 from the angles 13H-100,
13H-110, 13H-130 and from the lavatory structure.
(b) Remove the screws 13H-120 and the angles 13H-100, 13H-110 from the floor
panel assembly 13H-050.
(c) Remove the screws 13H-140, the washers 13H-160 and the angle 13H-130
from the floor panel assembly 13H-050.
(d) Remove the screws 13H-170 and the floor panel assembly 13H-050 from the
lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-810-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-004-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Adhesive/Sealant
one Part, RTV
Silicone Rubber
Table 3223
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the lamp cover assembly 14-010 from the double spring ball catches
14-030.
(b) Remove the screws 14-040, the washers 14-050 and the double spring ball
catches 14-030 from the lavatory structure.
(c) Remove the fluorescent lamp 14-090 from the ballast unit 14-100.
(d) Remove the screws 14-070, 14-075, the washers 14-080, the reflector 14-060
and the ballast unit 14-100 from the lavatory structure.
SUBTASK 25-41-58-040-004-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
For Myanmar Airways (MMA) use only
Table 3224
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the lamp cover assembly 14-010 from the double spring ball catches
14-030.
(b) Remove the screws 14-040, the washers 14-050 and the double spring ball
catches 14-030 from the lavatory structure.
(c) Remove the fluorescent lamp 14-090 from the advanced integrated ballast
unit 14-100.
(d) Remove the screws 14-070, 14-075, the washers 14-080, the spacers 14-110,
14-120, the reflector 14-060 and the advanced integrated ballast unit 14-100
from the lavatory structure.
TASK 25-41-58-000-810-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-005-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Adhesive/Sealant
one Part, RTV
Silicone Rubber
Table 3225
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the lamp cover assembly 14A-010 from the double spring ball catches
14A-030.
(b) Remove the screws 14A-040, the washers 14A-050 and the double spring ball
catches 14A-030 from the lavatory structure.
(c) Remove the fluorescent lamp 14A-090 from the ballast unit 14A-100.
(d) Remove the screws 14A-070, 14A-075, the washers 14A-080, the reflector
14A-060 and the ballast unit 14A-100.
SUBTASK 25-41-58-040-005-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Adhesive/Sealant
one Part, RTV
Silicone Rubber
Table 3226
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the lamp cover assembly 14A-010 from the double spring ball catches
14A-030.
(b) Remove the screws 14A-040, the washers 14A-050 and the double spring ball
catches 14A-030 from the lavatory structure.
(c) Remove the fluorescent lamp 14A-090 from the advanced integrated ballast
unit 14A-100.
(d) Remove the screws 14A-070, 14A-075, the washers 14A-080, the spacers
14A-110, 14A-120, the reflector 14A-060 and the advanced integrated ballast
unit 14A-100.
TASK 25-41-58-000-810-C01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-004-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Adhesive/Sealant
one Part, RTV
Silicone Rubber
Table 3227
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the lamp cover assembly 14B-010 from the double spring ball catches
14B-030.
(b) Remove the screws 14B-060, the washers 14B-070 and the part of the
double-spring ball catches 14B-030 from the lavatory structure.
(c) Remove the screws 14B-080, the washers 14B-090 and the brackets 14B-050.
TASK 25-41-58-000-811-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-040-007-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
(a) Remove the cotter pins 15-180, the bolts 15-160, the washers 15-170 and
the damper 15-150 from the waste flap assembly 15-020 and from the waste
chute 18-010.
(c) Remove the ground cable from the washbasin assembly 15-010.
(d) Remove the screws 15-230, 15–235, the washers 15-220, 15–225 and the
washbasin assembly 15-010 from the washbasin unit bracket 15-240.
(e) Remove the screws 15-200, the washers 15-220, the nuts 15-300 and the
washbasin assembly 15-010 from the angles 15-270.
(f) Remove the screws 15-190, the washers 15-210 and the washbasin assembly
15-010 from the lavatory structure.
1 Remove the screws 15-120, the washers 15-130, the clip nuts 15-140 and
the waste flap assembly 15-020.
a Remove the screws 15-040, the washers 15-050 and the flap 15-030
from the flap hinge half 15-070.
– Remove the retaining rings 15-110, the axle 15-090 and the
springs 15-100 from the washbasin hinge half 15-080 and from
the flap hinge half 15-070.
(h) Remove the screws 15-290, the washers 15-210 and the angles 15-270 from
the lavatory structure.
For Myanmar Airways (MMA) use only
(j) Remove the screws 15-260, the washers 15-220 and the washbasin unit
bracket 15-240 from the lavatory structure.
SUBTASK 25-41-58-040-007-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
(a) Remove the soap dispenser washer 15-430 from the washbasin assembly
15-010.
(b) Remove the liquid-soap dispenser assy 15-450 from the bracket 15-440.
(c) Remove the bracket 15-440 from the washbasin assembly 15-010.
(d) Remove the soap dispenser adaptor 15-445 from the washbasin assembly
15-010.
a Remove the nut 15-360, the seal 15-350 and the pump 15-330.
(f) Remove the cotter pins 15-180, the bolts 15-160, the washers 15-170 and
the damper 15-150 from the waste flap assembly 15-020 and from the waste
chute 18-010.
(h) Remove the ground cable from the washbasin assembly 15-010.
(j) Remove the screws 15-230, the washers 15-220 and the washbasin assembly
15-010 from the washbasin unit bracket 15-240.
(k) Remove the screws 15-200, the washers 15-220, the nuts 15-300 and the
washbasin assembly 15-010 from the angles 15-270.
(l) Remove the screws 15-190, the washers 15-210 and the washbasin assembly
15-010 from the lavatory structure.
1 Remove the screws 15-120, the washers 15-130, the clip nuts 15-140 and
the waste flap assembly 15-020.
a Remove the screws 15-040, the washers 15-050 and the flap 15-030
from the flap hinge half 15-070.
– Remove the retaining rings 15-110, the axle 15-090 and the
springs 15-100 from the washbasin hinge half 15-080 and from
the flap hinge half 15-070.
(n) Remove the screws 15-290, the washers 15-210 and the angles 15-270 from
the lavatory structure.
(p) Remove the screws 15-260, the washers 15-220 and the washbasin unit
bracket 15-240 from the lavatory structure.
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-040-007-C01
D2549020303600 D2549020308000
(0) Removal and Disassembly of the Washbasin Unit (15-1), (18-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
(a) Remove the screws 15-420, the soap dispenser bracket 15-410 and the spacer
15-400 from the washbasin assembly 15-010.
(b) Remove the cotter pins 15-180, the bolts 15-160, the washers 15-170 and
the damper 15-150 from the waste flap assembly 15-020 and from the waste
chute 18-010.
(d) Remove the ground cable from the washbasin assembly 15-010.
(e) Remove the screws 15-230, the washers 15-220 and the washbasin assembly
15-010 from the washbasin unit bracket 15-240.
(f) Remove the screws 15-200, the washers 15-220, the nuts 15-300 and the
washbasin assembly 15-010 from the angles 15-270.
(g) Remove the screws 15-190, the washers 15-210 and the washbasin assembly
15-010 from the lavatory structure.
1 Remove the screws 15-120, the washers 15-130, the clip nuts 15-140 and
the waste flap assembly 15-020.
a Remove the screws 15-040, the washers 15-050 and the flap 15-030
from the flap hinge half 15-070.
– Remove the retaining rings 15-110, the axle 15-090 and the
springs 15-100 from the washbasin hinge half 15-080 and from
the flap hinge half 15-070.
(i) Remove the screws 15-290, the washers 15-210 and the angles 15-270 from
the lavatory structure.
(j) Remove the screws 15-260, the washers 15-220 and the washbasin unit
bracket 15-240 from the lavatory structure.
TASK 25-41-58-000-811-B01
A. General
– Cleaning
For Myanmar Airways (MMA) use only
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-008-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the ground cable from the washbasin assembly 15A-010.
(b) Remove the screw 15A-190, the washers 15A-200, the nut 15A-210 and the
washbasin assembly 15A-010 from the washbasin bracket 15A-160.
(c) Remove the screws 15A-120, the washers 15A-150 and the washbasin
assembly 15A-010 from the angles 15A-170.
(d) Remove the screws 15A-120, the washers 15A-130, the rear cover 15A-020
and the washbasin 15A-030 from the lavatory structure.
1 Remove the screws 15A-090, the washers 15A-100, the nuts 15A-110
and the flap assembly 15A-040 from the washbasin 15A-030.
a Remove the splints 15A-070, the pins 15A-060 and the springs
15A-080 from the flap 15A-050.
(f) Remove the screw 15A-120, the washer 15A-150 and the bracket 15A-220
from the lavatory structure.
(g) Remove the screws 15A-140, the washers 15A-130 and the angles 15A-170
from the lavatory structure.
(h) Remove the screws 15A-140, the washers 15A-150 and the washbasin bracket
15A-160 from the lavatory structure.
SUBTASK 25-41-58-040-008-B01
D2549010407400 R225401823-000
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the liquid-soap dispenser support 15A-350 from the washbasin
assembly 15A-010.
(b) Remove the ground cable from the washbasin assembly 15A-010.
(c) Remove the screw 15A-190, the washers 15A-200, the nut 15A-210 and the
washbasin assembly 15A-010 from the washbasin bracket 15A-160.
(d) Remove the screws 15A-120, the washers 15A-150 and the washbasin
assembly 15A-010 from the angles 15A-170.
(e) Remove the screws 15A-120, the washers 15A-130, the rear cover 15A-020
and the washbasin 15A-030 from the lavatory structure.
1 Remove the screws 15A-090, the washers 15A-100, the nuts 15A-110
and the flap assembly 15A-040 from the washbasin 15A-030.
a Remove the splints 15A-070, the pins 15A-060 and the springs
15A-080 from the flap 15A-050.
(g) Remove the screw 15A-120, the washer 15A-150 and the bracket 15A-220
from the lavatory structure.
(h) Remove the screws 15A-140, the washers 15A-130 and the angles 15A-170
from the lavatory structure.
(j) Remove the screws 15A-140, the washers 15A-150 and the washbasin bracket
15A-160 from the lavatory structure.
SUBTASK 25-41-58-040-008-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
a Remove the nut 15A-310, the seal 15A-300 and the pump 15A-280.
(b) Remove the ground cable from the washbasin assembly 15A-010.
(c) Remove the screw 15A-190, the washers 15A-200, the nut 15A-210 and the
washbasin assembly 15A-010 from the washbasin bracket 15A-160.
(d) Remove the screws 15A-120, the washers 15A-150 and the washbasin
assembly 15A-010 from the angles 15A-170.
(e) Remove the screws 15A-120, the washers 15A-130, the rear cover 15A-020
and the washbasin 15A-030 from the lavatory structure.
For Myanmar Airways (MMA) use only
1 Remove the screws 15A-090, the washers 15A-100, the nuts 15A-110
and the flap assembly 15A-040 from the washbasin 15A-030.
a Remove the splints 15A-070, the pins 15A-060 and the springs
15A-080 from the flap 15A-050.
(g) Remove the screw 15A-120, the washer 15A-150 and the bracket 15A-220
from the lavatory structure.
(h) Remove the screws 15A-140, the washers 15A-130 and the angles 15A-170
from the lavatory structure.
(j) Remove the screws 15A-140, the washers 15A-150 and the washbasin bracket
15A-160 from the lavatory structure.
TASK 25-41-58-000-811-C01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-009-A01
D2549020307200 D2549030708000
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Material No.
08-025 Two
Component
Polyurethane
Adhesive
(a) Remove the cotter pins 15B-360, the bolts 15B-340, the washers 15B-350
and the damper 15B-330 from the waste flap assembly 15B-030 and from the
waste chute 18-010.
(c) Remove the ground cable from the washbasin assembly 15B-010.
(d) Remove the screws 15B-310, the washers 15B-240 and the washbasin
assembly 15B-010 from the washbasin unit bracket 15B-290.
(e) Remove the screws 15B-230, the washers 15B-240, the nuts 15B-250 and the
washbasin assembly 15B-010 from the angles 15B-270.
(f) Remove the screws 15B-200, the washers 15B-210 and the washbasin
assembly 15B-010 from the lavatory structure.
1 Remove the screws 15B-130, the washers 15B-140, the clip nuts 15B-150
and the waste flap assembly 15B-030 from the washbasin 15B-020.
a Remove the screws 15B-050, the washers 15B-060 and the flap
15B-040 from the flap hinge half 15B-080.
– Remove the retaining rings 15B-120, the axle 15B-100 and the
springs 15B-110 from the washbasin hinge half 15B-090 and from
the flap hinge half 15B-080.
(h) Remove the screws 15B-180, the washers 15B-190 and the brackets 15B-170
from the washbasin 15B-020.
(j) Remove the screws 15B-260, the washers 15B-210 and the angles 15B-270
from the lavatory structure.
(k) Remove the screws 15B-320, the washers 15B-240 and the washbasin unit
bracket 15B-290 from the lavatory structure.
SUBTASK 25-41-58-040-009-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
a Remove the knurled nut 15B-440, the nut 15B-430, the seal 15B-420
and the pump 15B-400.
(b) Remove the cotter pins 15B-360, the bolts 15B-340, the washers 15B-350
and the damper 15B-330 from the waste flap assembly 15B-030 and from the
waste chute 18-010.
(d) Remove the ground cable from the washbasin assembly 15B-010.
(e) Remove the screws 15B-310, the washers 15B-240 and the washbasin
assembly 15B-010 from the washbasin unit bracket 15B-290.
For Myanmar Airways (MMA) use only
(f) Remove the screws 15B-230, the washers 15B-240, the nuts 15B-250 and the
washbasin assembly 15B-010 from the angles 15B-270.
(g) Remove the screws 15B-200, the washers 15B-210 and the washbasin
assembly 15B-010 from the lavatory structure.
1 Remove the screws 15B-130, the washers 15B-140, the clip nuts 15B-150
and the waste flap assembly 15B-030 from the washbasin 15B-020.
a Remove the screws 15B-050, the washers 15B-060 and the flap
15B-040 from the flap hinge half 15B-080.
– Remove the retaining rings 15B-120, the axle 15B-100 and the
springs 15B-110 from the washbasin hinge half 15B-090 and from
the flap hinge half 15B-080.
(i) Remove the screws 15B-180, the washers 15B-190 and the brackets 15B-170
from the washbasin 15B-020.
(j) Remove the screws 15B-260, the washers 15B-210 and the angles 15B-270
from the lavatory structure.
(k) Remove the screws 15B-320, the washers 15B-240 and the washbasin unit
bracket 15B-290 from the lavatory structure.
SUBTASK 25-41-58-040-009-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the liquid-soap dispenser support 15B-370 from the washbasin
assembly 15B-010.
(b) Remove the cotter pins 15B-360, the bolts 15B-340, the washers 15B-350
and the damper 15B-330 from the waste flap assembly 15B-030 and from the
waste chute 18-010.
(d) Remove the ground cable from the washbasin assembly 15B-010.
(e) Remove the screws 15B-310, the washers 15B-240 and the washbasin
assembly 15B-010 from the washbasin unit bracket 15B-290.
(f) Remove the screws 15B-230, the washers 15B-240, the nuts 15B-250 and the
washbasin assembly 15B-010 from the angles 15B-270.
For Myanmar Airways (MMA) use only
(g) Remove the screws 15B-200, the washers 15B-210 and the washbasin
assembly 15B-010 from the lavatory structure.
1 Remove the screws 15B-130, the washers 15B-140, the clip nuts 15B-150
and the waste flap assembly 15B-030 from the washbasin 15B-020.
a Remove the screws 15B-050, the washers 15B-060 and the flap
15B-040 from the flap hinge half 15B-080.
– Remove the retaining rings 15B-120, the axle 15B-100 and the
springs 15B-110 from the washbasin hinge half 15B-090 and from
the flap hinge half 15B-080.
(i) Remove the screws 15B-180, the washers 15B-190 and the brackets 15B-170
from the washbasin 15B-020.
(j) Remove the screws 15B-260, the washers 15B-210 and the angles 15B-270
from the lavatory structure.
(k) Remove the screws 15B-320, the washers 15B-240 and the washbasin unit
bracket 15B-290 from the lavatory structure.
SUBTASK 25-41-58-040-009-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
For Myanmar Airways (MMA) use only
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the liquid-soap dispenser bottle 15B-220 from the liquid-soap
dispenser support 15B-370.
(b) Remove the liquid-soap dispenser support 15B-370 from the washbasin
assembly 15B-010.
(c) Remove the cotter pins 15B-360, the bolts 15B-340, the washers 15B-350
and the damper 15B-330 from the waste flap assembly 15B-030 and from the
waste chute 18-010.
(e) Remove the ground cable from the washbasin assembly 15B-010.
(f) Remove the screws 15B-310, the washers 15B-240 and the washbasin
assembly 15B-010 from the washbasin unit bracket 15B-290.
For Myanmar Airways (MMA) use only
(g) Remove the screws 15B-230, the washers 15B-240, the nuts 15B-250 and the
washbasin assembly 15B-010 from the angles 15B-270.
(h) Remove the screws 15B-200, the washers 15B-210 and the washbasin
assembly 15B-010 from the lavatory structure.
1 Remove the screws 15B-130, the washers 15B-140, the clip nuts 15B-150
and the waste flap assembly 15B-030 from the washbasin 15B-020.
a Remove the screws 15B-050, the washers 15B-060 and the flap
15B-040 from the flap hinge half 15B-080.
– Remove the retaining rings 15B-120, the axle 15B-100 and the
springs 15B-110 from the washbasin hinge half 15B-090 and from
the flap hinge half 15B-080.
(k) Remove the screws 15B-180, the washers 15B-190 and the brackets 15B-170
from the washbasin 15B-020.
(l) Remove the screws 15B-260, the washers 15B-210 and the angles 15B-270
from the lavatory structure.
(m) Remove the screws 15B-320, the washers 15B-240 and the washbasin unit
bracket 15B-290 from the lavatory structure.
SUBTASK 25-41-58-040-009-E01
NOTE: See TABLE for the references for the replacement procedures of
For Myanmar Airways (MMA) use only
(a) Remove the liquid-soap dispenser support 15B-370 from the washbasin
assembly 15B-010.
a Remove the knurled nut 15B-440, the nut 15B-430, the seal 15B-420
and the pump 15B-400.
For Myanmar Airways (MMA) use only
(c) Remove the cotter pins 15B-360, the bolts 15B-340, the washers 15B-350
and the damper 15B-330 from the waste flap assembly 15B-030 and from the
waste chute 18-010.
(e) Remove the ground cable from the washbasin assembly 15B-010.
(f) Remove the screws 15B-310, the washers 15B-240 and the washbasin
assembly 15B-010 from the washbasin unit bracket 15B-290.
(g) Remove the screws 15B-230, the washers 15B-240, the nuts 15B-250 and the
washbasin assembly 15B-010 from the angles 15B-270.
(h) Remove the screws 15B-200, the washers 15B-210 and the washbasin
assembly 15B-010 from the lavatory structure.
1 Remove the screws 15B-130, the washers 15B-140, the clip nuts 15B-150
and the waste flap assembly 15B-030 from the washbasin 15B-020.
a Remove the screws 15B-050, the washers 15B-060 and the flap
15B-040 from the flap hinge half 15B-080.
– Remove the retaining rings 15B-120, the axle 15B-100 and the
springs 15B-110 from the washbasin hinge half 15B-090 and from
the flap hinge half 15B-080.
(k) Remove the screws 15B-180, the washers 15B-190 and the brackets 15B-170
from the washbasin 15B-020.
(l) Remove the screws 15B-260, the washers 15B-210 and the angles 15B-270
from the lavatory structure.
For Myanmar Airways (MMA) use only
(m) Remove the screws 15B-320, the washers 15B-240 and the washbasin unit
bracket 15B-290 from the lavatory structure.
TASK 25-41-58-000-811-D01
R225411620-000 R225411623-000
76. Removal and Disassembly of the Washbasin Unit
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-040-010-A01
D2549020911000 D2549020913800
(1) Removal and Disassembly of the Washbasin Unit (15C-1), (18-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
(a) Remove the cotter pins 15C-180, the bolts 15C-160, the washers 15C-170 and
the damper 15C-150 from the waste flap assembly 15C-020 and from the
waste chute 18-010.
(c) Remove the ground cable from the washbasin assembly 15C-010.
(d) Remove the screws 15C-310, the washers 15C-220 and the washbasin
assembly 15C-010 from the washbasin unit bracket 15C-240.
(e) Remove the screws 15C-210, the washers 15C-220, the nuts 15C-300 and the
washbasin assembly 15C-010 from the angles 15C-270.
(f) Remove the screws 15C-190, the washers 15C-200 and the washbasin
assembly 15C-010 from the lavatory structure.
1 Remove the screws 15C-120, the washers 15C-130, the clip nuts
For Myanmar Airways (MMA) use only
a Remove the screws 15C-040, the washers 15C-050 and the flap
15C-030 from flap hinge half 15C-070.
– Remove the retaining rings 15C-110, the axle 15C-090 and the
springs 15C-100 from the washbasin hinge half 15C-080 and
from flap hinge half 15C-070.
(h) Remove the screws 15C-290, the washers 15C-200 and the angles 15C-270
from the lavatory structure.
(j) Remove the screws 15C-260, the washers 15C-200 and the washbasin unit
bracket 15C-240 from the lavatory structure.
SUBTASK 25-41-58-040-010-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
350-802-A01
Table 3240
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the soap dispenser washer 15C-420 from the washbasin assembly
15C-010.
a Remove the nut 15C-380, the seal 15C-370 and the pump 15C-350.
(c) Remove the cotter pins 15C-180, the bolts 15C-160, the washers 15C-170 and
the damper 15C-150 from the waste flap assembly 15C-020 and from the
waste chute 18-010.
(e) Remove the ground cable from the washbasin assembly 15C-010.
(f) Remove the screws 15C-310, the washers 15C-220 and the washbasin
assembly 15C-010 from the washbasin unit bracket 15C-240.
(g) Remove the screws 15C-210, the washers 15C-220, the nuts 15C-300 and the
washbasin assembly 15C-010 from the angles 15C-270.
(h) Remove the screws 15C-190, the washers 15C-200 and the washbasin
assembly 15C-010 from the lavatory structure.
1 Remove the screws 15C-120, the washers 15C-130, the clip nuts
For Myanmar Airways (MMA) use only
a Remove the screws 15C-040, the washers 15C-050 and the flap
15C-030 from flap hinge half 15C-070.
– Remove the retaining rings 15C-110, the axle 15C-090 and the
springs 15C-100 from the washbasin hinge half 15C-080 and
from flap hinge half 15C-070.
(k) Remove the screws 15C-290, the washers 15C-200 and the angles 15C-270
from the lavatory structure.
(l) Remove the screws 15C-260, the washers 15C-200 and the washbasin unit
bracket 15C-240 from the lavatory structure.
SUBTASK 25-41-58-040-010-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
(a) Remove the liquid-soap dispenser support 15C-320 from the washbasin
assembly 15C-010.
(b) Remove the cotter pins 15C-180, the bolts 15C-160, the washers 15C-170 and
the damper 15C-150 from the waste flap assembly 15C-020 and from the
waste chute 18-010.
(d) Remove the ground cable from the washbasin assembly 15C-010.
(e) Remove the screws 15C-310, the washers 15C-220 and the washbasin
assembly 15C-010 from the washbasin unit bracket 15C-240.
(f) Remove the screws 15C-210, the washers 15C-220, the nuts 15C-300 and the
washbasin assembly 15C-010 from the angles 15C-270.
(g) Remove the screws 15C-190, the washers 15C-200 and the washbasin
assembly 15C-010 from the lavatory structure.
1 Remove the screws 15C-120, the washers 15C-130, the clip nuts
15C-140 and the waste flap assembly 15C-020.
a Remove the screws 15C-040, the washers 15C-050 and the flap
15C-030 from flap hinge half 15C-070.
– Remove the retaining rings 15C-110, the axle 15C-090 and the
springs 15C-100 from the washbasin hinge half 15C-080 and
from flap hinge half 15C-070.
For Myanmar Airways (MMA) use only
(i) Remove the screws 15C-290, the washers 15C-200 and the angles 15C-270
from the lavatory structure.
(j) Remove the screws 15C-260, the washers 15C-200 and the washbasin unit
bracket 15C-240 from the lavatory structure.
SUBTASK 25-41-58-040-010-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
(a) Remove the liquid-soap dispenser bottle 15C-230 from the liquid-soap
dispenser support 15C-320.
(b) Remove the liquid-soap dispenser support 15C-320 from the washbasin
assembly 15C-010.
(c) Remove the cotter pins 15C-180, the bolts 15C-160, the washers 15C-170 and
the damper 15C-150 from the waste flap assembly 15C-020 and from the
waste chute 18-010.
(e) Remove the ground cable from the washbasin assembly 15C-010.
(f) Remove the screws 15C-310, the washers 15C-220 and the washbasin
assembly 15C-010 from the washbasin unit bracket 15C-240.
(g) Remove the screws 15C-210, the washers 15C-220, the nuts 15C-300 and the
washbasin assembly 15C-010 from the angles 15C-270.
(h) Remove the screws 15C-190, the washers 15C-200 and the washbasin
assembly 15C-010 from the lavatory structure.
1 Remove the screws 15C-120, the washers 15C-130, the clip nuts
15C-140 and the waste flap assembly 15C-020.
a Remove the screws 15C-040, the washers 15C-050 and the flap
15C-030 from flap hinge half 15C-070.
– Remove the retaining rings 15C-110, the axle 15C-090 and the
For Myanmar Airways (MMA) use only
(k) Remove the screws 15C-290, the washers 15C-200 and the angles 15C-270
from the lavatory structure.
(l) Remove the screws 15C-260, the washers 15C-200 and the washbasin unit
bracket 15C-240 from the lavatory structure.
TASK 25-41-58-000-811-E01
D2547160900800 D2549020900600
77. Removal and Disassembly of the Washbasin Unit
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-011-A01
(1) Removal and Disassembly of the Washbasin Unit (15D-1), (18-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
350-802-A01
a Remove the nut 15D-310, the seal 15D-300 and the pump 15D-280.
(b) Remove the cotter pins 15D-380, the bolts 15D-360, the washers 15D-370 and
the damper 15D-350 from the flap assembly 15D-040 and from the waste
chute 18-010.
(d) Remove the ground cable from the washbasin assembly 15D-010.
(e) Remove the screw 15D-190, the washers 15D-200, the nut 15D-210 and the
washbasin assembly 15D-010 from the washbasin bracket 15D-160.
(f) Remove the screws 15D-120, the washers 15D-150 and the washbasin
assembly 15D-010 from the angles 15D-170.
(g) Remove the screws 15D-120, the washers 15D-130, the rear cover 15D-020
and the washbasin 15D-030 from the lavatory structure.
1 Remove the screws 15D-090, the washers 15D-100, the nuts 15D-110
and the flap assembly 15D-040 from the washbasin 15D-030.
a Remove the splints 15D-070, the pins 15D-060 and the springs
15D-080 from the flap 15D-050.
(i) Remove the screw 15D-120, the washer 15D-150 and the bracket 15D-220
from the lavatory structure.
(j) Remove the screws 15D-140, the washers 15D-130 and the angles 15D-170
from the lavatory structure.
(k) Remove the screws 15D-140, the washers 15D-150 and the washbasin bracket
15D-160 from the lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-811-F01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-012-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
a Remove the knurled nut 15E-420, the nut 15E-410, the seal 15E-400
and the pump 15E-380.
(b) Remove the cotter pins 15E-350, the bolts 15E-330, the washers 15E-340
and the damper 15E-320 from the waste flap assembly 15E-030 and from the
waste chute 18-010.
(d) Remove the ground cable from the washbasin assembly 15E-010.
(e) Remove the screws 15E-300, the washers 15E-230 and the washbasin
assembly 15E-010 from the washbasin unit bracket 15E-280.
For Myanmar Airways (MMA) use only
(f) Remove the screws 15E-220, the washers 15E-230, the nuts 15E-240 and the
washbasin assembly 15E-010 from the angles 15E-260.
(g) Remove the screws 15E-200, the washers 15E-210 and the washbasin
assembly 15E-010 from the lavatory structure.
1 Remove the screws 15E-130, the washers 15E-140, the clip nuts 15E-150
and the waste flap assembly 15E-030 from the washbasin 15E-020.
a Remove the screws 15E-050, the washers 15E-060 and the flap
15E-040 from the flap hinge half 15E-080.
– Remove the retaining rings 15E-120, the axle 15E-100 and the
springs 15E-110 from the washbasin hinge half 15E-090 and from
the flap hinge half 15E-080.
(i) Remove the screws 15E-180, the washers 15E-190 and the brackets 15E-170
from the washbasin 15E-020.
(j) Remove the screws 15E-250, the washers 15E-210 and the angles 15E-260
from the lavatory structure.
(k) Remove the screws 15E-310, the washers 15E-230 and the washbasin unit
bracket 15E-280 from the lavatory structure.
SUBTASK 25-41-58-040-012-B01
D2549030810600 R225401889-002
(0) Removal and Disassembly of the Washbasin Unit (15E-1), (18-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
For Myanmar Airways (MMA) use only
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Table 3245
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the liquid-soap dispenser support 15E-450 from the washbasin
assembly 15E-010.
(b) Remove the cotter pins 15E-350, the bolts 15E-330, the washers 15E-340
and the damper 15E-320 from the waste flap assembly 15E-030 and from the
waste chute 18-010.
(d) Remove the ground cable from the washbasin assembly 15E-010.
(e) Remove the screws 15E-300, the washers 15E-230 and the washbasin
assembly 15E-010 from the washbasin unit bracket 15E-280.
(f) Remove the screws 15E-220, the washers 15E-230, the nuts 15E-240 and the
washbasin assembly 15E-010 from the angles 15E-260.
For Myanmar Airways (MMA) use only
(g) Remove the screws 15E-200, the washers 15E-210 and the washbasin
assembly 15E-010 from the lavatory structure.
1 Remove the screws 15E-130, the washers 15E-140, the clip nuts 15E-150
and the waste flap assembly 15E-030 from the washbasin 15E-020.
a Remove the screws 15E-050, the washers 15E-060 and the flap
15E-040 from the flap hinge half 15E-080.
– Remove the retaining rings 15E-120, the axle 15E-100 and the
springs 15E-110 from the washbasin hinge half 15E-090 and from
the flap hinge half 15E-080.
(i) Remove the screws 15E-180, the washers 15E-190 and the brackets 15E-170
from the washbasin 15E-020.
(j) Remove the screws 15E-250, the washers 15E-210 and the angles 15E-260
from the lavatory structure.
(k) Remove the screws 15E-310, the washers 15E-230 and the washbasin unit
bracket 15E-280 from the lavatory structure.
SUBTASK 25-41-58-040-012-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
For Myanmar Airways (MMA) use only
(a) Remove the liquid-soap dispenser bottle 15E-460 from the liquid-soap
dispenser support 15E-450.
(b) Remove the liquid-soap dispenser support 15E-450 from the washbasin
assembly 15E-010.
(c) Remove the cotter pins 15E-350, the bolts 15E-330, the washers 15E-340
and the damper 15E-320 from the waste flap assembly 15E-030 and from the
waste chute 18-010.
(e) Remove the ground cable from the washbasin assembly 15E-010.
(f) Remove the screws 15E-300, the washers 15E-230 and the washbasin
assembly 15E-010 from the washbasin unit bracket 15E-280.
(g) Remove the screws 15E-220, the washers 15E-230, the nuts 15E-240 and the
washbasin assembly 15E-010 from the angles 15E-260.
For Myanmar Airways (MMA) use only
(h) Remove the screws 15E-200, the washers 15E-210 and the washbasin
assembly 15E-010 from the lavatory structure.
1 Remove the screws 15E-130, the washers 15E-140, the clip nuts 15E-150
and the waste flap assembly 15E-030 from the washbasin 15E-020.
a Remove the screws 15E-050, the washers 15E-060 and the flap
15E-040 from the flap hinge half 15E-080.
– Remove the retaining rings 15E-120, the axle 15E-100 and the
springs 15E-110 from the washbasin hinge half 15E-090 and from
the flap hinge half 15E-080.
(k) Remove the screws 15E-180, the washers 15E-190 and the brackets 15E-170
from the washbasin 15E-020.
(l) Remove the screws 15E-250, the washers 15E-210 and the angles 15E-260
from the lavatory structure.
(m) Remove the screws 15E-310, the washers 15E-230 and the washbasin unit
bracket 15E-280 from the lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-811-G01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-040-013-A01
D2549026001200
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
INSTALLED PARTS
a Remove the nut 15F-380, the seal 15F-370 and the pump 15F-350.
(b) Remove the cotter pins 15F-180, the bolts 15F-160, the washers 15F-170
and the damper 15F-150 from the waste flap assembly 15F-020 and from the
waste chute 18-010.
(d) Remove the ground cable from the washbasin assembly 15F-010.
(e) Remove the screws 15F-310, the washers 15F-220 and the washbasin
assembly 15F-010 from the washbasin unit bracket 15F-240.
(f) Remove the screws 15F-210, the washers 15F-220, the nuts 15F-300 and the
washbasin assembly 15F-010 from the angles 15F-270.
(g) Remove the screws 15F-190, the washers 15F-200 and the washbasin
assembly 15F-010 from the lavatory structure.
1 Remove the screws 15F-120, the washers 15F-130, the clip nuts 15F-140
and the waste flap assembly 15F-020.
a Remove the screws 15F-040, the washers 15F-050 and the flap
15F-030 from the flap hinge half 15F-070.
– Remove the retaining rings 15F-110, the axle 15F-090 and the
springs 15F-100 from the washbasin hinge half 15F-080 and from
the flap hinge half 15F-070.
(i) Remove the screws 15F-290, the washers 15F-200 and the angles 15F-270
from the lavatory structure.
(j) Remove the screws 15F-260, the washers 15F-200 and the washbasin unit
bracket 15F-240 from the lavatory structure.
SUBTASK 25-41-58-040-013-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3248
For Myanmar Airways (MMA) use only
(a) Remove the liquid-soap dispenser bottle 15F-230 from the liquid-soap
dispenser support 15F-320.
(b) Remove the liquid-soap dispenser support 15F-320 from the washbasin
assembly 15F-010.
(c) Remove the cotter pins 15F-180, the bolts 15F-160, the washers 15F-170
and the damper 15F-150 from the waste flap assembly 15F-020 and from the
waste chute 18-010.
(e) Remove the ground cable from the washbasin assembly 15F-010.
(f) Remove the screws 15F-310, the washers 15F-220 and the washbasin
assembly 15F-010 from the washbasin unit bracket 15F-240.
(g) Remove the screws 15F-210, the washers 15F-220, the nuts 15F-300 and the
washbasin assembly 15F-010 from the angles 15F-270.
(h) Remove the screws 15F-190, the washers 15F-200 and the washbasin
assembly 15F-010 from the lavatory structure.
1 Remove the screws 15F-120, the washers 15F-130, the clip nuts 15F-140
and the waste flap assembly 15F-020.
a Remove the screws 15F-040, the washers 15F-050 and the flap
15F-030 from the flap hinge half 15F-070.
– Remove the retaining rings 15F-110, the axle 15F-090 and the
springs 15F-100 from the washbasin hinge half 15F-080 and from
the flap hinge half 15F-070.
(k) Remove the screws 15F-290, the washers 15F-200 and the angles 15F-270
from the lavatory structure.
(l) Remove the screws 15F-260, the washers 15F-200 and the washbasin unit
bracket 15F-240 from the lavatory structure.
TASK 25-41-58-000-811-H01
D2549010414600
80. Removal and Disassembly of the Washbasin Unit
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-008-A01
(1) Removal and Disassembly of the Washbasin Unit (15G-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
08-025 Two
Component
Polyurethane
Adhesive
Table 3249
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screws 15G-280 and the vase 15G-220 from the washbasin
assembly 15G-010.
(b) Remove the washers 15G-320, the nuts 15G-340 and the soap dispenser
holder 15G-190 from the washbasin assembly 15G-010.
(c) Remove the screws 15G-290, the washers 15G-300, the spacer 15G-210 and
the cosmetics holder 15G-200 from the washbasin assembly 15G-010.
(d) Remove the ground cable from the washbasin assembly 15G-010.
(e) Remove the screws 15G-250, the washers 15G-310 and the washbasin
assembly 15G-010 from the washbasin unit bracket 15G-230.
(f) Remove the screws 15G-250, the washers 15G-330, the nuts 15G-350 and
the washbasin assembly 15G-010.
(g) Remove the screws 15G-260, the washers 15G-310 and the washbasin
assembly 15G-010 from the lavatory structure.
(h) Remove the screws 15G-250, the washers 15G-330 and the washbasin
assembly 15G-010 from the lavatory structure.
1 Remove the screws 15G-150, the washers 15G-160, the clip nuts
15G-180 and the waste flap assembly 15G-040 from the washbasin
15G-020.
a Remove the screws 15G-060, the washers 15G-070 and the flap
15G-050 from the flap hinge half 15G-090.
– Remove the retaining rings 15G-130, the axle 15G-110 and the
springs 15G-120 from the washbasin hinge half 15G-100 and
from the flap hinge half 15G-090.
(k) Remove the screws 15G-140 and the washers 15G-170 from the washbasin
15G-020.
(l) Remove the screws 15G-270, the washers 15G-310 and the washbasin unit
bracket 15G-230 from the lavatory structure.
TASK 25-41-58-000-812-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-000-082-A01
(1) Removal and Disassembly of the Door Assembly of the Washbasin Unit (16-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove and disassemble the washbasin unit door assembly 16-010 as follows:
1 Remove the washbasin unit door assembly 16-010 and the attach pins
16-020, 16-030 from the mounting angle assemblies 16-070, 16-090.
2 Remove the attach pins 16-020, 16-030 from the washbasin unit door
assembly 16-010.
3 Remove the screws 16-040 and the latch assembly 16-050 from the
washbasin unit door assembly 16-010.
(b) Remove the screw 16-110, 16-113, the washer 16-120 and the mounting angle
assembly 16-070.
(d) Remove the screws 16-110, 16-112, 16-113, the washers 16-180, the nuts
16-190 and the mounting angle assembly 16-090.
(f) Remove the screws 16-110, 16-200, the washers 16-120, the nut 16-190, the
angle 16-140 and the sealing section 16-150 from the lavatory structure.
(g) Remove the screws 16-170, the washers 16-130 and the catch 16-160 from
the angle 16-140.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-812-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-000-083-A01
(1) Removal and Disassembly of the Door Assembly of the Washbasin Unit (16A-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove and disassemble the washbasin unit door assembly 16A-010 as
follows:
1 Remove the washbasin unit door assembly 16A-010 and the attach
pins 16A-020, 16A-030 from the mounting angle assemblies 16A-070,
16A-090.
2 Remove the attach pins 16A-020, 16A-030 from the washbasin unit door
assembly 16A-010.
3 Remove the screws 16A-040 and the latch assembly 16A-050 from the
washbasin unit door assembly 16A-010.
(b) Remove the screw 16A-110, the washer 16A-120 and the mounting angle
assembly 16A-070.
(d) Remove the screws 16A-110, 16A-115, the washers 16A-180, the nut 16A-190
and the mounting angle assembly 16A-090.
(f) Remove the screws 16A-110, 16A-200, the washers 16A-120, the nut 16A-190,
the angle 16A-140 and the sealing section 16A-150 from the lavatory structure.
(g) Remove the screws 16A-170, the washers 16A-130 and the catch 16A-160
from the angle 16A-140.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-812-C01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-000-084-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
For Myanmar Airways (MMA) use only
(a) Remove and disassemble the washbasin unit door assembly 16B-010 as
follows:
1 Remove the washbasin unit door assembly 16B-010 and the attach
pins 16B-020, 16B-030 from the mounting angle assemblies 16B-070,
16B-100.
2 Remove the attach pins 16B-020, 16B-030 from the washbasin unit door
assembly 16B-010.
3 Remove the screws 16B-040 and the latch assembly 16B-050 from the
washbasin unit door assembly 16B-010.
(b) Remove the screw 16B-130, the washer 16B-140 and the mounting angle
assembly 16B-070.
(d) Remove the screws 16B-130, the washers 16B-200, the nut 16B-210 and the
mounting angle assembly 16B-100.
(f) Remove the screws 16B-130, 16B-220, the washers 16B-140, the nut 16B-210,
the angle 16B-160 and the sealing section 16B-170 from the lavatory structure.
For Myanmar Airways (MMA) use only
(g) Remove the screws 16B-190, the washers 16B-150 and the catch 16B-180
from the angle 16B-160.
SUBTASK 25-41-58-000-084-B01
D2549010300000
(0) Removal and Disassembly of the Door Assembly of the Washbasin Unit (16B-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove and disassemble the washbasin unit door assembly 16B-010 as
follows:
1 Remove the washbasin unit door assembly 16B-010 and the attach
pins 16B-020, 16B-030 from the mounting angle assemblies 16B-070,
16B-100.
2 Remove the attach pins 16B-020, 16B-030 from the washbasin unit door
assembly 16B-010.
3 Remove the screws 16B-040 and the latch assembly 16B-050 from the
washbasin unit door assembly 16B-010.
(b) Remove the screw 16B-130, the washer 16B-140 and the mounting angle
assembly 16B-070.
For Myanmar Airways (MMA) use only
(d) Remove the screws 16B-130, the washers 16B-200, the nut 16B-210 and the
mounting angle assembly 16B-100.
(f) Remove the screws 16B-130, 16B-220, the washers 16B-140, the nut 16B-210,
the angle 16B-160 and the sealing section 16B-170 from the lavatory structure.
(g) Remove the screws 16B-190, the washers 16B-150 and the catch 16B-180
from the angle 16B-160.
(h) Remove the screws 16B-240 and the catch bracket 16B-230 from the lavatory
structure.
(j) Remove the screw 16B-260 and the catch 16B-250 from the catch bracket
16B-230.
TASK 25-41-58-000-812-D01
D2549010414600
84. Removal and Disassembly of the Door Assembly of the Washbasin Unit
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-000-086-A01
(1) Removal and Disassembly of the Door Assembly of the Washbasin Unit (16C-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove and disassemble the washbasin unit door assembly 16C-010 as
follows:
1 Remove the washbasin unit door assembly 16C-010 and the attach pins
16C-020, 16C-030 from the mounting angle assembly 16C-070 and from
the mounting angle 16C-100.
2 Remove the attach pins 16C-020, 16C-030 from the washbasin unit door
assembly 16C-010.
3 Remove the screws 16C-050 and the latch assembly 16C-060 from the
washbasin unit door assembly 16C-010.
(b) Remove the screws 16C-110, the washers 16C-130 and the mounting angle
assembly 16C-070.
(d) Remove the screws 16C-120, the washers 16C-130 and the mounting angle
16C-100.
TASK 25-41-58-000-813-A01
R225401884-000 R225401886-000
85. Removal and Disassembly of the Panel Assembly of the Washbasin Unit
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
B. Procedure
SUBTASK 25-41-58-000-088-A01
(a) Remove the ground cable from the washbasin unit panel assembly 17-010.
(b) Remove the screws 17-020, the washers 17-030 and the washbasin unit panel
assembly 17-010 from the lavatory structure.
(c) Remove the paper roll holder assembly 17-040 from the washbasin unit panel
assembly 17-010.
SUBTASK 25-41-58-000-088-B01
(a) Remove the ground cable from the washbasin unit panel assembly 17-010.
(b) Remove the screws 17-020, the washers 17-030 and the washbasin unit panel
assembly 17-010 from the lavatory structure.
(c) Remove the screws 17-015 from the washbasin unit panel assembly 17-010.
(d) Remove the paper roll holder assembly 17-040 from the washbasin unit panel
assembly 17-010.
TASK 25-41-58-000-813-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
B. Procedure
SUBTASK 25-41-58-000-091-A01
(a) Remove the ground cable from the washbasin unit panel assembly 17A-010.
(b) Remove the screws 17A-020, the washers 17A-030 and the washbasin unit
panel assembly 17A-010 from the lavatory structure.
(c) Remove the paper roll holder assembly 17A-040 from the washbasin unit panel
assembly 17A-010.
SUBTASK 25-41-58-000-091-B01
(a) Remove the ground cable from the washbasin unit panel assembly 17A-010.
(b) Remove the screws 17A-020, the washers 17A-030 and the washbasin unit
panel assembly 17A-010 from the lavatory structure.
(c) Remove the screws 17A-015 from the washbasin unit panel assembly 17A-010.
(d) Remove the paper roll holder assembly 17A-040 from the washbasin unit panel
assembly 17A-010.
TASK 25-41-58-000-813-C01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
B. Procedure
SUBTASK 25-41-58-000-093-A01
(a) Remove the ground cable from the washbasin unit panel assembly 17B-010.
(b) Remove the screws 17B-020, the washers 17B-030 and the washbasin unit
panel assembly 17B-010 from the lavatory structure.
For Myanmar Airways (MMA) use only
(c) Remove the paper roll holder assembly 17B-040 from the washbasin unit panel
assembly 17B-010.
SUBTASK 25-41-58-000-093-B01
(a) Remove the ground cable from the washbasin unit panel assembly 17B-010.
(b) Remove the screws 17B-020, the washers 17B-030 and the washbasin unit
panel assembly 17B-010 from the lavatory structure.
(c) Remove the screws 17B-015 from the washbasin unit panel assembly 17B-010.
(d) Remove the paper roll holder assembly 17B-040 from the washbasin unit panel
assembly 17B-010.
TASK 25-41-58-000-813-D01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
B. Procedure
SUBTASK 25-41-58-000-094-A01
(1) Removal and Disassembly of the Panel Assembly of the Washbasin Unit (17C-1)
(a) Remove the ground cable from the washbasin unit panel assembly 17C-010.
(b) Remove the screws 17C-020, the washers 17C-030 and the washbasin unit
panel assembly 17C-010 from the lavatory structure.
(c) Remove the screws 17C-015 from the washbasin unit panel assembly 17C-010.
(d) Remove the paper roll holder assembly 17C-040 from the washbasin unit panel
assembly 17C-010.
TASK 25-41-58-000-813-E01
D2549010414600
89. Removal and Disassembly of the Panel Assembly of the Washbasin Unit
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-089-A01
(1) Removal and Disassembly of the Panel Assembly of the Washbasin Unit (17D-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Angle 350-802-A01
(a) Remove the ground cable from the washbasin unit panel assembly 17D-010.
(b) Remove the screws 17D-120, the washers 17D-140 and the washbasin unit
panel assembly 17D-010 from the lavatory structure.
a Remove the screws 17D-120, the washers 17D-140 and the bracket
17D-100 from the washbasin unit panel assembly 17D-010.
2 Remove the screws 17D-120, the washers 17D-140 and the washbasin
unit bracket 17D-050.
3 Remove the screws 17D-120, the washers 17D-140 and the angle
17D-060.
4 Remove the screws 17D-130, the washers 17D-140 and the fittings
17D-150.
(d) Remove the paper roll holder assembly 17D-020 from the washbasin unit panel
assembly 17D-010.
TASK 25-41-58-000-814-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT YOU DO NOT BEND THE DISCHARGE TUBE
WHEN YOU REMOVE OR INSTALL THE FIRE EXTINGUISHER. IF
YOU DO, YOU CAN CAUSE DAMAGE TO THE JOINT BETWEEN THE
DISCHARGE TUBE AND THE CONTAINER.
SUBTASK 25-41-58-040-022-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Waste Box
Console
Assembly
(a) Remove the waste container 18-050 from the waste box console assembly
18-060.
(b) Remove the screws 18-040, the washers 18-150, 18-170, the clip nuts 18-180
and the fire extinguisher 18-160.
(c) Remove the screws 18-040 and the waste chute 18-010 from the waste box
console assembly 18-060.
(d) Remove the screws 18-140, the washers 18-150 and the waste box console
assembly 18-060 from the lavatory structure.
1 Remove the screws 18-100, the washers 18-110, the nuts 18-120 and
the cover 18-090.
(f) Remove and disassemble the door ejector assembly 18-190 as follows:
1 Remove the screws 18-240, the washers 18-250, the nuts 18-260 and
the door ejector assembly 18-190 from the waste box console assembly
18-060.
2 Remove the hinge pin 18-220, the spring 18-230 and the door ejector pin
18-210 from the door ejector housing 18-200.
SUBTASK 25-41-58-040-022-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Waste Box
Console
Assembly
(a) Remove the waste container 18-050 from the waste box console assembly
18-060.
(b) Remove the screws 18-040, the washers 18-150, 18-170, the clip nuts 18-180
and the fire extinguisher 18-160.
(c) Remove the screws 18-040 and the waste chute 18-010 from the waste box
console assembly 18-060.
(d) Remove the screws 18-140, the washers 18-150 and the waste box console
assembly 18-060 from the lavatory structure.
1 Remove the screws 18-100, the washers 18-110, the nuts 18-120 and
the cover 18-090.
(f) Remove and disassemble the door ejector assembly 18-190 as follows:
1 Remove the screws 18-240, the washers 18-250, the nuts 18-260 and
the door ejector assembly 18-190 from the waste box console assembly
18-060.
2 Remove the hinge pin 18-220, the spring 18-230 and the door ejector pin
18-210 from the door ejector housing 18-200.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-815-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-080-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the service box assembly 19-290 from the service cabinet assembly
19-010.
3 Remove the screws 19-330, the handle 19-340 and the handle holders
19-320.
1 Remove the screws 19-040, the washers 19-060, the nuts 19-050 and the
block 19-030 from the upper part service cabinet assembly 19-020.
2 Remove the screws 19-260, the washers 19-270, the nuts 19-280 and the
angle assemblies 19-160 from the center part service cabinet 19-070.
For Myanmar Airways (MMA) use only
4 Remove the screws 19-220, the washers 19-210 and the upper part
service cabinet assembly 19-020 from the lavatory structure.
5 Remove the center part service cabinet 19-070 with the hinge pin 19-100
from the hinge 19-090.
6 Remove the screws 19-220, the washers 19-210 and the hinge 19-090
from the lavatory structure.
8 Remove the soap dispenser assemblies 19-145 from the chutes 19-155.
9 Remove the chutes 19-155 from the lower part service cabinet 19-080.
10 Remove the screws 19-230 and the lower part service cabinet 19-080
from the angle brackets 19-190.
11 Remove the screws 19-220, the washers 19-210 and the lower part
service cabinet 19-080 from the lavatory structure.
12 Remove the screws 19-200, the washers 19-210 and the angle brackets
19-190 from the lavatory structure.
13 Remove the washers 19-250, the nuts 19-240, the loaded spring latches
19-130 and the bushings 19-120 from the upper part service cabinet
assembly 19-020 and from the lower part service cabinet 19-080.
(d) Remove the set screw 19-400 and the passenger service unit PSU 19-360 from
the lower part service cabinet 19-080.
1 Remove the front frame assembly 19-370 from the bracket 19-450.
2 Remove the set screw 19-430 and the shaver outlet 19-420 from the
For Myanmar Airways (MMA) use only
bracket 19-450.
4 Remove the call switch wire-harness 19-440 from the bracket 19-450.
SUBTASK 25-41-58-000-080-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the label 19-460 from the service cabinet assembly 19-010.
(b) Remove the label 19-460 and the protective film 19-470 from the service
cabinet assembly 19-010.
(c) Remove the service box assembly 19-290 from the service cabinet assembly
19-010.
3 Remove the screws 19-330, the handle 19-340 and the handle holders
19-320.
1 Remove the screws 19-040, the washers 19-060, the nuts 19-050 and the
block 19-030 from the upper part service cabinet assembly 19-020.
2 Remove the screws 19-260, the washers 19-270, the nuts 19-280 and the
angle assemblies 19-160 from the center part service cabinet 19-070.
4 Remove the screws 19-220, 19-225, the washers 19-210 and the upper
part service cabinet assembly 19-020 from the lavatory structure.
5 Remove the center part service cabinet 19-070 with the hinge pin 19-100
from the hinge 19-090.
6 Remove the screws 19-220, the washers 19-210 and the hinge 19-090
from the lavatory structure.
8 Remove the screws 19-230 and the lower part service cabinet 19-080
from the angle brackets 19-190.
9 Remove the screws 19-220, the washers 19-210 and the lower part
service cabinet 19-080 from the lavatory structure.
10 Remove the screws 19-200, the washers 19-210 and the angle bracket
19-190 from the lavatory structure.
11 Remove the screws 19-205, the washers 19-215, the nuts 19-217 and
the angle bracket 19-190.
12 Remove the washers 19-250, the nuts 19-240, the loaded spring latches
19-130 and the bushings 19-120 from the upper part service cabinet
assembly 19-020 and from the lower part service cabinet 19-080.
(f) Remove the set screw 19-400 and the passenger service unit PSU 19-360 from
the lower part service cabinet 19-080.
1 Remove the front frame assembly 19-370 from the bracket 19-450.
2 Remove the set screw 19-430 and the shaver outlet 19-420 from the
bracket 19-450.
4 Remove the call switch wire-harness 19-440 from the bracket 19-450.
SUBTASK 25-41-58-000-080-C01
D2549020307200 D2549030708000
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the service box assembly 19-290 from the service cabinet assembly
19-010.
3 Remove the screws 19-330, the handle 19-340 and the handle holders
19-320.
1 Remove the screws 19-040, the washers 19-060, the nuts 19-050 and the
block 19-030 from the upper part service cabinet assembly 19-020.
2 Remove the screws 19-260, the washers 19-270, the nuts 19-280 and the
angle assemblies 19-160 from the center part service cabinet 19-070.
For Myanmar Airways (MMA) use only
4 Remove the screws 19-220, the washers 19-210 and the upper part
service cabinet assembly 19-020 from the lavatory structure.
5 Remove the center part service cabinet 19-070 with the hinge pin 19-100
from the hinge 19-090.
6 Remove the screws 19-220, the washers 19-210 and the hinge 19-090
from the lavatory structure.
8 Remove the screws 19-230 and the lower part service cabinet 19-080
from the angle brackets 19-190.
9 Remove the screws 19-220, the washers 19-210 and the lower part
service cabinet 19-080 from the lavatory structure.
10 Remove the screws 19-200, the washers 19-210 and the angle brackets
19-190 from the lavatory structure.
11 Remove the washers 19-250, the nuts 19-240, the loaded spring latches
19-130 and the bushings 19-120 from the upper part service cabinet
assembly 19-020 and from the lower part service cabinet 19-080.
(d) Remove the set screw 19-400 and the passenger service unit PSU 19-360 from
the lower part service cabinet 19-080.
1 Remove the front frame assembly 19-370 from the bracket 19-450.
3 Remove the call switch wire-harness 19-440 from the bracket 19-450.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-815-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-087-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Assembly Material
No. 08-001
General
Purpose
Adhesive
Honeycomb
Filler
(a) Remove the service box assembly 19A-290 from the service cabinet assembly
19A-010.
3 Remove the screws 19A-330, the handle 19A-340 and the handle holders
19A-320.
1 Remove the screws 19A-040, the washers 19A-060, the nuts 19A-050 and
the block 19A-030 from the upper part service cabinet assembly 19A-020.
For Myanmar Airways (MMA) use only
2 Remove the screws 19A-260, the washers 19A-270, the nuts 19A-280
and the angle assemblies 19A-160 from the center part service cabinet
19A-070.
4 Remove the screws 19A-220, the washers 19A-210 and the upper part
service cabinet assembly 19A-020 from the lavatory structure.
5 Remove the center part service cabinet 19A-070 with the hinge pin
19A-100 from the hinge 19A-090.
6 Remove the screws 19A-220, the washers 19A-210 and the hinge
19A-090 from the lavatory structure.
9 Remove the chutes 19A-155 from the lower part service cabinet 19A-080.
10 Remove the screws 19A-230 and the lower part service cabinet 19A-080
from the angle brackets 19A-190.
11 Remove the screws 19A-220, the washers 19A-210 and the lower part
service cabinet 19A-080 from the lavatory structure.
12 Remove the screws 19A-200, the washers 19A-210 and the angle
brackets 19A-190 from the lavatory structure.
13 Remove the washers 19A-250, the nuts 19A-240, the loaded spring
latches 19A-130 and the bushings 19A-120 from the upper part service
cabinet assembly 19A-020 and from the lower part service cabinet
19A-080.
(d) Remove the set screw 19A-400 and the passenger service unit PSU 19A-360
from the lower part service cabinet 19A-080.
1 Remove the front frame assembly 19A-370 from the bracket 19A-450.
2 Remove the set screw 19A-430 and the shaver outlet 19A-420 from the
bracket 19A-450.
4 Remove the call switch wire-harness 19A-440 from the bracket 19A-450.
SUBTASK 25-41-58-000-087-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Assembly Material
No. 08-001
General
Purpose
Adhesive
Honeycomb
Filler
(a) Remove the service box assembly 19A-290 from the service cabinet assembly
19A-010.
3 Remove the screws 19A-330, the handle 19A-340 and the handle holders
19A-320.
1 Remove the screws 19A-040, the washers 19A-060, the nuts 19A-050 and
the block 19A-030 from the upper part service cabinet assembly 19A-020.
For Myanmar Airways (MMA) use only
2 Remove the screws 19A-260, the washers 19A-270, the nuts 19A-280
and the angle assemblies 19A-160 from the center part service cabinet
19A-070.
4 Remove the screws 19A-220, the washers 19A-210 and the upper part
service cabinet assembly 19A-020 from the lavatory structure.
5 Remove the center part service cabinet 19A-070 with the hinge pin
19A-100 from the hinge 19A-090.
6 Remove the screws 19A-220, the washers 19A-210 and the hinge
19A-090 from the lavatory structure.
8 Remove the screws 19A-230 and the lower part service cabinet 19A-080
from the angle brackets 19A-190.
9 Remove the screws 19A-220, the washers 19A-210 and the lower part
service cabinet 19A-080 from the lavatory structure.
10 Remove the screws 19A-200, the washers 19A-210 and the angle
brackets 19A-190 from the lavatory structure.
11 Remove the washers 19A-250, the nuts 19A-240, the loaded spring
latches 19A-130 and the bushings 19A-120 from the upper part service
cabinet assembly 19A-020 and from the lower part service cabinet
19A-080.
(d) Remove the set screw 19A-400 and the passenger service unit PSU 19A-360
from the lower part service cabinet 19A-080.
1 Remove the front frame assembly 19A-370 from the bracket 19A-450.
For Myanmar Airways (MMA) use only
2 Remove the set screw 19A-430 and the shaver outlet 19A-420 from the
bracket 19A-450.
4 Remove the call switch wire-harness 19A-440 from the bracket 19A-450.
(f) Remove the protective film 19A-470 and the label 19A-460 from the service
cabinet assembly 19A-010.
SUBTASK 25-41-58-000-087-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Assembly Material
No. 08-001
General
Purpose
Adhesive
Honeycomb
Filler
(a) Remove the service box assembly 19A-290 from the service cabinet assembly
19A-010.
3 Remove the screws 19A-330, the handle 19A-340 and the handle holders
19A-320.
1 Remove the screws 19A-040, the washers 19A-060, the nuts 19A-050 and
the block 19A-030 from the upper part service cabinet assembly 19A-020.
For Myanmar Airways (MMA) use only
2 Remove the screws 19A-260, the washers 19A-270, the nuts 19A-280
and the angle assemblies 19A-160 from the center part service cabinet
19A-070.
4 Remove the screws 19A-220, the washers 19A-210 and the upper part
service cabinet assembly 19A-020 from the lavatory structure.
5 Remove the center part service cabinet 19A-070 with the hinge pin
19A-100 from the hinge 19A-090.
6 Remove the screws 19A-220, the washers 19A-210 and the hinge
19A-090 from the lavatory structure.
8 Remove the screws 19A-230 and the lower part service cabinet 19A-080
from the angle brackets 19A-190.
9 Remove the screws 19A-220, the washers 19A-210 and the lower part
service cabinet 19A-080 from the lavatory structure.
10 Remove the screws 19A-200, the washers 19A-210 and the angle
brackets 19A-190 from the lavatory structure.
11 Remove the washers 19A-250, the nuts 19A-240, the loaded spring
latches 19A-130 and the bushings 19A-120 from the upper part service
cabinet assembly 19A-020 and from the lower part service cabinet
19A-080.
(d) Remove the set screw 19A-400 and the passenger service unit PSU 19A-360
from the lower part service cabinet 19A-080.
1 Remove the front frame assembly 19A-370 from the bracket 19A-450.
For Myanmar Airways (MMA) use only
4 Remove the call switch wire-harness 19A-440 from the bracket 19A-450.
SUBTASK 25-41-58-000-087-D01
D2547160900800
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Assembly Material
No. 08-001
General
Purpose
Adhesive
Honeycomb
Filler
1 Remove the screws 19A-040, the washers 19A-060, the nuts 19A-050 and
the block 19A-030 from the upper part service cabinet assembly 19A-020.
2 Remove the screws 19A-260, the washers 19A-270, the nuts 19A-280
and the angle assemblies 19A-160 from the center part service cabinet
19A-070.
4 Remove the screws 19A-220, the washers 19A-210 and the upper part
service cabinet assembly 19A-020 from the lavatory structure.
5 Remove the center part service cabinet 19A-070 with the hinge pin
19A-100 from the hinge 19A-090.
6 Remove the screws 19A-220, the washers 19A-210 and the hinge
For Myanmar Airways (MMA) use only
8 Remove the screws 19A-230 and the lower part service cabinet 19A-080
from the angle brackets 19A-190.
9 Remove the screws 19A-220, the washers 19A-210 and the lower part
service cabinet 19A-080 from the lavatory structure.
10 Remove the screws 19A-200, the washers 19A-210 and the angle
brackets 19A-190 from the lavatory structure.
11 Remove the washers 19A-250, the nuts 19A-240, the loaded spring
latches 19A-130 and the bushings 19A-120 from the upper part service
cabinet assembly 19A-020 and from the lower part service cabinet
19A-080.
(b) Remove the set screw 19A-400 and the passenger service unit PSU 19A-360
from the lower part service cabinet 19A-080.
1 Remove the front frame assembly 19A-370 from the bracket 19A-450.
2 Remove the set screw 19A-430 and the shaver outlet 19A-420 from the
bracket 19A-450.
4 Remove the call switch wire-harness 19A-440 from the bracket 19A-450.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-815-C01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-000-092-A01
D2549010301000 D2549010414600
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the label 19B-015 and the protective film 19B-016 from the service
cabinet assembly 19B-010.
(b) Remove the service box assembly 19B-290 from the service cabinet assembly
19B-010.
3 Remove the screws 19B-330, the handle 19B-340 and the handle holders
19B-320.
1 Remove the screws 19B-040, the washers 19B-060, the nuts 19B-050 and
the block 19B-030 from the upper part service cabinet assembly 19B-020.
For Myanmar Airways (MMA) use only
2 Remove the screws 19B-260, the washers 19B-270, the nuts 19B-280
and the angle assemblies 19B-160 from the center part service cabinet
19B-070.
4 Remove the screws 19B-220, the washers 19B-210 and the upper part
service cabinet assembly 19B-020 from the lavatory structure.
5 Remove the center part service cabinet 19B-070 with the hinge pin
19B-100 from the hinge 19B-090.
6 Remove the screws 19B-220, the washers 19B-210 and the hinge
19B-090 from the lavatory structure.
8 Remove the screws 19B-230 and the lower part service cabinet 19B-080
from the angle brackets 19B-190.
9 Remove the screws 19B-220, the washers 19B-210 and the lower part
service cabinet 19B-080 from the lavatory structure.
10 Remove the screws 19B-200, the washers 19B-210 and the angle
brackets 19B-190 from the lavatory structure.
11 Remove the washers 19B-250, the nuts 19B-240, the loaded spring
latches 19B-130 and the bushings 19B-120 from the upper part service
cabinet assembly 19B-020 and from the lower part service cabinet
19B-080.
(e) Remove the set screw 19B-400 and the passenger service unit PSU 19B-360
from the lower part service cabinet 19B-080.
1 Remove the front frame assembly 19B-370 from the bracket 19B-450.
For Myanmar Airways (MMA) use only
2 Remove the set screw 19B-430 and the shaver outlet 19B-420 from the
bracket 19B-450.
4 Remove the call switch wire-harness 19B-440 from the bracket 19B-450.
SUBTASK 25-41-58-000-092-B01
D2549010300000
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
1 Remove the screws 19B-040, the washers 19B-060, the nuts 19B-050 and
the block 19B-030 from the upper part service cabinet assembly 19B-020.
2 Remove the screws 19B-260, the washers 19B-270, the nuts 19B-280
and the angle assemblies 19B-160 from the center part service cabinet
19B-070.
4 Remove the screws 19B-220, the washers 19B-210 and the upper part
service cabinet assembly 19B-020 from the lavatory structure.
5 Remove the center part service cabinet 19B-070 with the hinge pin
19B-100 from the hinge 19B-090.
6 Remove the screws 19B-220, the washers 19B-210 and the hinge
For Myanmar Airways (MMA) use only
8 Remove the screws 19B-230 and the lower part service cabinet 19B-080
from the angle brackets 19B-190.
9 Remove the screws 19B-220, the washers 19B-210 and the lower part
service cabinet 19B-080 from the lavatory structure.
10 Remove the screws 19B-200, the washers 19B-210 and the angle
brackets 19B-190 from the lavatory structure.
11 Remove the washers 19B-250, the nuts 19B-240, the loaded spring
latches 19B-130 and the bushings 19B-120 from the upper part service
cabinet assembly 19B-020 and from the lower part service cabinet
19B-080.
(b) Remove the set screw 19B-400 and the passenger service unit PSU 19B-360
from the lower part service cabinet 19B-080.
1 Remove the front frame assembly 19B-370 from the bracket 19B-450.
2 Remove the set screw 19B-430 and the shaver outlet 19B-420 from the
bracket 19B-450.
4 Remove the call switch wire-harness 19B-440 from the bracket 19B-450.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-816-A01
R225411620-000 R225411623-000
94. Removal and Disassembly of the Nursing Table
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-000-079-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Table 3267
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screws 20-090, 20-095 and the hook assembly 20-080 from the
lavatory structure.
(b) Remove the screws 20-090 and the nursing table assembly 20-010 from the
lavatory structure.
SUBTASK 25-41-58-000-079-B01
D2549020902600 D2549020908200
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Table 3268
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Remove the screws 20-090 and the catch 20-080 from the lavatory structure.
(b) Remove the screws 20-090 and the nursing table assembly 20-010 from the
lavatory structure.
2 Remove the screws 20-030, 20-035 and the latch assembly 20-020.
TASK 25-41-58-000-816-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
B. Procedure
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-000-085-A01
(1) Removal and Disassembly of the Nursing Table (20A-1)
(a) Remove the screws 20A-090 and the hook assembly 20A-080 from the
lavatory structure.
(b) Remove the screws 20A-090 and the nursing table assembly 20A-010 from
the lavatory structure.
TASK 25-41-58-000-817-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-029-A01
(1) Disassembly of the Ventilation System (21-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Material No.
08-010A Epoxy
Resin and
Hardener
Adhesive
(a) Remove the individual air outlet 21-010 from the lavatory structure.
(b) Remove the clamp 21-020 and the individual air outlet 21-010 from the cap
21-030.
(c) Remove the clamp 21-040 and the cap 21-030 from the hose 21-060.
(d) Remove the clamp 21-040 and the hose 21-060 from the tube 21-070.
(e) Remove the screws 21-090, the washers 21-100, the clamps 21-120 and the
tube 21-070 from the lavatory rear wall.
(f) Remove the clamp 21-040 and the tube 21-070 from the hose 21-080.
(j) Remove the screws 21-160 and the air extraction bracket 21-150 from the
ceiling panel.
For Myanmar Airways (MMA) use only
(k) Remove the screws 21-230 and the louver 21-140, the grille 21-210 and the
fleece 21-220 from the ceiling panel.
(l) Remove the screws 21-200 and the air extraction hood 21-130 from the ceiling
panel.
TASK 25-41-58-000-817-B01
D2549026000600 D2549030812000
97. Disassembly of the Ventilation System
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-030-A01
(1) Disassembly of the Ventilation System (21A-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
08-010A Epoxy
Resin and Hardener
Adhesive
(a) Remove the individual air outlet 21A-010 from the lavatory structure.
(b) Remove the clamp 21A-020 and the individual air outlet 21A-010 from the
cap 21A-030.
(c) Remove the clamp 21A-040 and the cap 21A-030 from the hose 21A-060.
(d) Remove the clamp 21A-040 and the hose 21A-060 from the tube 21A-070.
(e) Remove the screws 21A-090, the washers 21A-100, the clamps 21A-120 and
the tube 21A-070 from the lavatory rear wall.
(f) Remove the clamp 21A-040 and the tube 21A-070 from the hose 21A-080.
(j) Remove the screws 21A-160 and the air extraction bracket 21A-150 from the
ceiling panel.
(k) Remove the screws 21A-230 and the louver 21A-140, the grille 21A-210 and
the fleece 21A-220 from the ceiling panel.
(l) Remove the screws 21A-200 and the air extraction hood 21A-130 from the
For Myanmar Airways (MMA) use only
ceiling panel.
TASK 25-41-58-000-818-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-040-031-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Bracket
(a) Disconnect the water faucet assembly 22-010 from the water supply.
(b) Remove the ground cable from the water faucet assembly 22-010.
(c) Remove the screw 22-090, the washer 22-050, the clamps 22-080, the spacer
22-100 and the tube of the water faucet assembly 22-010 from the lavatory
structure.
(d) Remove the tube of the water faucet assembly 22-010 from the reducer elbow
22-070.
(e) Remove the screw 22-090, the washer 22-050, the clamp 22-080, the spacer
22-100 and the tube of the water faucet assembly 22-010 from the lavatory
structure.
(f) Remove the tube of the water faucet assembly 22-010 from the tee 22-230.
(g) Remove the water faucet assembly 22-010 from the lavatory structure.
(h) Remove the reducer elbow 22-070 from the water heater 22-060.
(j) Remove the tee 22-230 from the hose 22-240 and from the water heater
22-060.
For Myanmar Airways (MMA) use only
(m) Remove the tube 22-250 from the shutoff valve 22-210.
(n) Remove the screw 22-280, the washer 22-050, the clamp 22-270, the spacer
22-290 and the tube 22-250 from the lavatory structure.
(p) Remove the tee 22-220 from the shutoff valve 22-210.
(q) Remove the ground cable from the water heater 22-060.
(r) Remove the clamps 22-030 with the water heater 22-060 from the brackets
22-020.
(s) Remove the screws 22-040, the washers 22-050 and the brackets 22-020
from the lavatory structure.
(t) Remove the ground cable from the shutoff valve 22-210.
(u) Remove the screws 22-140, the washers 22-050, the nuts 22-150 and the
bracket 22-130 with the grommet 22-120 from the shutoff valve rod 22-110 and
from the lavatory structure.
(v) Remove the screws 22-140, the washers 22-180 and the bracket 22-170 with
the retaining ring 22-160, the grommet 22-120, the shutoff valve rod 22-110
and the shutoff valve bracket 22-190 from the lavatory structure.
(w) Remove the shutoff valve rod 22-110 from the shutoff valve 22-210.
(x) Remove the screws 22-320, the washers 22-330, the shutoff valve 22-210
and the shutoff valve bracket 22-190.
SUBTASK 25-41-58-040-031-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
(a) Disconnect the water faucet assembly 22-010 from the water supply.
(b) Remove the ground cable from the water faucet assembly 22-010.
(c) Remove the screw 22-090, the washer 22-050, the clamps 22-080, the spacer
22-100 and the tube of the water faucet assembly 22-010 from the lavatory
structure.
(d) Remove the tube of the water faucet assembly 22-010 from the reducer elbow
22-070.
(e) Remove the screw 22-090, the washer 22-050, the clamp 22-080, the spacer
22-100 and the tube of the water faucet assembly 22-010 from the lavatory
structure.
(f) Remove the tube of the water faucet assembly 22-010 from the tee 22-230.
(g) Remove the water faucet assembly 22-010 from the lavatory structure.
(h) Remove the reducer elbow 22-070 from the water heater 22-060.
(j) Remove the tee 22-230 from the hose 22-240 and from the water heater
22-060.
(m) Remove the tube 22-250 from the shutoff valve 22-210.
(n) Remove the tee 22-220 from the shutoff valve 22-210.
(p) Remove the ground cable from the water heater 22-060.
(q) Remove the clamps 22-030 with the water heater 22-060 from the brackets
22-020.
For Myanmar Airways (MMA) use only
(r) Remove the screws 22-040, the washers 22-050 and the brackets 22-020
from the lavatory structure.
(s) Remove the ground cable from the shutoff valve 22-210.
(t) Remove the screws 22-140, the washers 22-050, the nuts 22-150 and the
bracket 22-130 with the grommet 22-120 from the shutoff valve rod 22-110 and
from the lavatory structure.
(u) Remove the screws 22-140, the washers 22-180 and the bracket 22-170 with
the retaining ring 22-160, the grommet 22-120, the shutoff valve rod 22-110
and the shutoff valve bracket 22-190 from the lavatory structure.
(v) Remove the shutoff valve rod 22-110 from the shutoff valve 22-210.
(w) Remove the screws 22-320, the washers 22-330, the shutoff valve 22-210
and the shutoff valve bracket 22-190.
TASK 25-41-58-000-818-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-040-032-A01
(1) Disassembly of the Potable Water System (22A-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
Table 3273
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
(a) Disconnect the infrared faucet assembly 22A-010 from the water supply and
from the electrical supply.
(b) Remove the ground cable from the infrared faucet assembly 22A-010.
(c) Remove the screw 22A-020 and the infrared faucet assembly 22A-010.
(d) Remove the screws 22A-120, the washers 22A-060, the clamps 22A-100, the
spacers 22A-110 and the hose 22A-090 from the lavatory structure.
(e) Remove the hose 22A-090 from the tee 22A-260 and from the valve of the
infrared faucet assembly 22A-010.
(f) Remove the hose 22A-080 from the water heater 22A-070 and from the valve
of the infrared faucet assembly 22A-010.
(g) Remove the screws 22A-050, the washers 22A-060, the nut 22A-180 and the
remaining parts of the infrared faucet assembly 22A-010.
(h) Remove the screws 22A-050, the washers 22A-060 and the angle 22A-130
from the lavatory structure.
(j) Remove the tee 22A-260 from the water heater 22A-070 and from the hose
22A-270.
(m) Remove the tee 22A-250 from the shutoff valve 22A-240.
(n) Remove the tube 22A-280 from the shutoff valve 22A-240.
(p) Remove the ground cable from the water heater 22A-070.
For Myanmar Airways (MMA) use only
(q) Remove the clamps 22A-040 with the water heater 22A-070 from the brackets
22A-030.
(r) Remove the screws 22A-050, the washers 22A-060 and the brackets 22A-030
from the lavatory structure.
(s) Remove the ground cable from the shutoff valve 22A-240.
(t) Remove the screws 22A-170, the washers 22A-060, the nut 22A-180 and the
bracket 22A-160 with the grommet 22A-150 from the shutoff valve rod 22A-140
and from the lavatory structure.
(u) Remove the screws 22A-170, the washers 22A-210 and the bracket 22A-200
with the retaining ring 22A-190, the grommet 22A-150, the shutoff valve rod
22A-140 and the shutoff valve bracket 22A-220 from the lavatory structure.
(v) Remove the shutoff valve rod 22A-140 from the shutoff valve 22A-240.
(w) Remove the screws 22A-300, the washers 22A-310, the shutoff valve 22A-240
and the shutoff valve bracket 22A-220.
TASK 25-41-58-000-818-C01
D2549010414600
100. Disassembly of the Potable Water System
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-040-033-A01
(1) Disassembly of the Potable Water System (22B-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Shutoff
Valve
Bracket
(a) Disconnect the water faucet assembly 22B-010 from the water supply and from
the electrical supply.
(b) Remove the ground cable from the water faucet assembly 22B-010.
(c) Remove the screws 22B-130, the washers 22B-160, the clamps 22B-090, the
spacers 22B-110 and the tube of the water faucet assembly 22B-010 from
the lavatory structure.
(d) Remove the screws 22B-120, the washers 22B-160 and the controller of the
water faucet assembly 22B-010 from the lavatory structure.
(e) Remove the screws 22B-120, the washers 22B-160 and the cover assembly
22B-070 from the lavatory structure.
(f) Remove the screws 22B-120, the washers 22B-160 and the valve of the water
faucet assembly 22B-010 from the lavatory structure.
(g) Remove the water faucet assembly 22B-010 from the lavatory structure.
(h) Remove the screws 22B-140, 22B-150, the washers 22B-160, the clamps
22B-020, the spacers 22B-030, 22B-100 and the hose 22B-060 from the
lavatory structure.
(j) Remove the hose 22B-060 from the tee 22B-330 and from the reducer elbow
For Myanmar Airways (MMA) use only
22B-080.
(k) Remove the hose 22B-050 from the reducer elbow 22B-040 and from the water
heater 22B-190.
(l) Remove the reducer elbows 22B-040, 22B-080 from the valve of the water
faucet assembly 22B-010.
(m) Remove the tee 22B-330 from the water heater 22B-190 and from the hose
22B-230.
(n) Remove the ground cable from the water heater 22B-190.
(p) Remove the clamps 22B-210 with the water heater 22B-190 from the brackets
22B-200.
(q) Remove the screws 22B-170, the washers 22B-160, the brackets 22B-200 and
the spacers 22B-180 from the lavatory structure.
(t) Remove the tube 22B-310 from the shutoff valve 22B-220.
(u) Remove the screw 22B-400, the washer 22B-440, the clamp 22B-340, the
spacer 22B-350 and the tube 22B-310 from the lavatory structure.
(v) Remove the tee 22B-320 from the shutoff valve 22B-220.
(w) Remove the ground cable from the shutoff valve 22B-220.
(x) Remove the screws 22B-410, the washers 22B-440, the nuts 22B-460 and the
bracket 22B-280 with the grommet 22B-300 from the shutoff valve rod 22B-290
and from the lavatory structure.
(y) Remove the screws 22B-410, the washers 22B-450 and the bracket 22B-270
with the retaining ring 22B-390, the grommet 22B-300, the shutoff valve rod
22B-290 and the shutoff valve bracket 22B-250 from the lavatory structure.
(z) Remove the shutoff valve rod 22B-290 from the shutoff valve 22B-220.
For Myanmar Airways (MMA) use only
(aa) Remove the screws 22B-420, the washers 22B-430, the shutoff valve 22B-220
and the shutoff valve bracket 22B-250.
TASK 25-41-58-000-819-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-040-034-B01
(a) Remove the clamps 23-030 and the hose 23-020 from the drain assembly
23-010, from the lavatory structure and from the drain valve 23-040.
(c) Remove the screw 23-180, the washer 23-170, the nut 23-190, the clamp
23-130 and the hose 23-120 from the lavatory structure.
(d) Remove the screw 23-160, the washer 23-170, the clamps 23-130, 23-135,
23-140, the spacers 23-150, 23-195 and the hose 23-120 from the lavatory
structure.
(e) Remove the clamp 23-030 and the hose 23-120 from the drain valve 23-040.
(f) Remove the clamp 23-030 and the hose 23-120 from the lavatory structure.
(g) Remove the ground cable from the drain valve 23-040.
(h) Remove the screws 23-090, the washers 23-100, the nuts 23-110 and the drain
valve 23-040 from the bracket 23-050.
(j) Remove the screws 23-060, the washers 23-070, the nuts 23-080 and the
bracket 23-050 from the lavatory structure.
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-040-034-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
(a) Remove the clamps 23-030 and the hose 23-020 from the drain assembly
23-010, from the lavatory structure and from the drain valve 23-040.
(c) Remove the screw 23-180, the washer 23-170, the nut 23-190, the clamp
23-130 and the hose 23-120 from the lavatory structure.
(d) Remove the screw 23-160, the washer 23-170, the clamps 23-130, 23-140, the
spacer 23-150 and the hose 23-120 from the lavatory structure.
(e) Remove the clamp 23-030 and the hose 23-120 from the drain valve 23-040.
For Myanmar Airways (MMA) use only
(f) Remove the clamp 23-030 and the hose 23-120 from the lavatory structure.
(g) Remove the ground cable from the drain valve 23-040.
(h) Remove the screws 23-090, the washers 23-100, the nuts 23-110 and the drain
valve 23-040 from the bracket 23-050.
(j) Remove the screws 23-060, the washers 23-070, the nuts 23-080 and the
bracket 23-050 from the lavatory structure.
TASK 25-41-58-000-820-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-036-A01
D2549020307200 D2549030708000
(1) Disassembly of the Electrical System (26-1)
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26-170, 26-180, 26-190, 26-200,
26-210 and the cable harness assembly 26-010 from the electrical components.
(c) Remove the screws 26-040, the nuts 26-050, the smoke detector 26-020 and
the smoke detector sealing 26-030.
For Myanmar Airways (MMA) use only
(e) Remove the screws 26-080, the washers 26-090 and the bracket 26-070 from
the lavatory structure.
(h) Remove the screws 26-080, the washers 26-090 and the bracket 26-070 from
the lavatory structure.
(l) Remove the screws 26-080, the washers 26-090 and the cable ties 26-110.
(m) Remove the screw 26-220, the washer 26-230 and the clamp 26-250.
(n) Remove the ami cabin attendant seat-cable 26-270, the connector backshell
26-310 and the plug connectors 26-300, 26-320.
SUBTASK 25-41-58-040-036-C01
NOTE: It is recommended that you only remove the components if they are
For Myanmar Airways (MMA) use only
damaged.
(a) Disconnect the cables, the bonding straps 26-170, 26-180, 26-190, 26-195,
26-200, 26-210 and the cable harness assembly 26-010 from the electrical
components.
(c) Remove the screws 26-040, the nuts 26-050, the smoke detector 26-020 and
the smoke detector sealing 26-030.
(e) Remove the screws 26-080, the washers 26-090 and the bracket 26-070 from
the lavatory structure.
(f) Remove the screws 26-380, the spacers 26-390 and the mini inverter 26-370.
(j) Remove the screws 26-080, the washers 26-090 and the bracket 26-070 from
the lavatory structure.
(l) Remove the nuts 26-196, 26-240 and the washers 26-197, 26-230.
For Myanmar Airways (MMA) use only
(m) Remove the screws 26-080, the washers 26-090 and the cable ties 26-110.
(n) Remove the screw 26-220, the washer 26-230 and the clamp 26-250.
(p) Remove the ami cabin attendant seat-cable 26-270, the connector backshell
26-310 and the plug connectors 26-300, 26-320.
SUBTASK 25-41-58-040-036-D01
D2549030709200
(0) Disassembly of the Electrical System (26-1)
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26-170, 26-180, 26-190, 26-200,
26-210 and the cable harness assembly 26-010 from the electrical components.
(c) Remove the screws 26-040, the nuts 26-050, the smoke detector 26-020 and
the smoke detector sealing 26-030.
(e) Remove the screws 26-080, the washers 26-090 and the bracket 26-070 from
the lavatory structure.
(f) Remove the screws 26-380, the spacers 26-390 and the mini inverter 26-370.
(j) Remove the screws 26-080, the washers 26-090 and the bracket 26-070 from
the lavatory structure.
(m) Remove the screws 26-080, the washers 26-090 and the cable ties 26-110.
(n) Remove the screw 26-220, the washer 26-230 and the clamp 26-250.
(p) Remove the ami cabin attendant seat-cable 26-270, the connector backshell
26-310 and the plug connectors 26-300, 26-320.
SUBTASK 25-41-58-040-036-E01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
Adhesive/Sealant
one Part, RTV
Silicone Rubber
Table 3276
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26-170, 26-180, 26-190, 26-200,
26-210 and the cable harness assembly 26-010 from the electrical components.
(c) Remove the screws 26-040, the nuts 26-050, the smoke detector 26-020 and
the smoke detector sealing 26-030.
(e) Remove the screws 26-080, the washers 26-090 and the bracket 26-070 from
the lavatory structure.
(f) Remove the screws 26-380, the spacers 26-390 and the mini inverter 26-370.
(j) Remove the screws 26-080, the washers 26-090 and the bracket 26-070 from
For Myanmar Airways (MMA) use only
(m) Remove the screws 26-080, the washers 26-090 and the cable ties 26-110.
(n) Remove the screw 26-220, the washer 26-230 and the clamp 26-250.
(p) Remove the ami cabin attendant seat-cable 26-270, the connector backshell
26-310 and the plug connectors 26-300, 26-320.
TASK 25-41-58-000-820-B01
A. General
– Cleaning
– Visual Inspection
For Myanmar Airways (MMA) use only
C. Procedure
SUBTASK 25-41-58-040-037-A01
(1) Disassembly of the Electrical System (26A-1)
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26A-200, 26A-210, 26A-220,
26A-250, 26A-260 and the cable harness assembly 26A-010 from the electrical
components.
(b) Remove the screws 26A-040, the nuts 26A-050, the smoke detector 26A-020
and the smoke detector sealing 26A-030.
(d) Remove the screws 26A-310, the spacers 26A-300 and the mini inverter
26A-290.
For Myanmar Airways (MMA) use only
(g) Remove the screws 26A-080, the washers 26A-090 and the bracket 26A-070
from the lavatory structure.
(h) Remove the screws 26A-170, the microswitch 26A-160 and the shrinkable heat
tubings 26A-180, 26A-190.
(l) Remove the screw 26A-230, the washer 26A-240 and the clamp 26A-280.
(m) Remove the ami cabin attendant seat-cable 26A-320, the connector backshell
26A-360 and the plug connectors 26A-350, 26A-370.
TASK 25-41-58-000-820-C01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-038-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26B-160, 26B-170, 26B-180,
26B-190, 26B-200 and the cable harness assembly 26B-010 from the electrical
components.
(b) Remove the screws 26B-040, the nuts 26B-050, the smoke detector 26B-020
and the smoke detector sealing 26B-030.
(d) Remove the screws 26B-250, the washers 26B-080 and the bracket 26B-070
from the lavatory structure.
(e) Remove the screws 26B-370, the spacers 26B-380 and the mini inverter
26B-360.
For Myanmar Airways (MMA) use only
(h) Remove the screws 26B-250, the washers 26B-080 and the bracket 26B-070
from the lavatory structure.
(l) Remove the screws 26B-250, the washers 26B-080 and the cable ties 26B-100.
(m) Remove the screw 26B-210, the washer 26B-220 and the clamp 26B-240.
(n) Remove the ami cabin attendant seat-cable 26B-260, the connector backshell
26B-300 and the plug connectors 26B-290, 26B-310.
(p) Remove and disassemble the 2065 VU switch panel 26B-390 as follows:
1 Remove the plugs 26B-500 from the printed circuit board PCB 26B-450.
a Remove the screws 26B-460, the spring washers 26B-470 and the
switch housing 26B-410 from the printed circuit board PCB 26B-450.
4 Remove the switch button-switch 26B-480 from the printed circuit board
PCB 26B-450.
SUBTASK 25-41-58-040-038-B01
For Myanmar Airways (MMA) use only
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26B-160, 26B-170, 26B-180,
26B-190, 26B-200 and the cable harness assembly 26B-010 from the electrical
components.
(b) Remove the screws 26B-040, the nuts 26B-050, the smoke detector 26B-020
and the smoke detector sealing 26B-030.
(d) Remove the screws 26B-250, the washers 26B-080 and the bracket 26B-070
from the lavatory structure.
For Myanmar Airways (MMA) use only
(e) Remove the screws 26B-370, the spacers 26B-380 and the mini inverter
26B-360.
(h) Remove the screws 26B-250, the washers 26B-080 and the bracket 26B-070
from the lavatory structure.
(l) Remove the screws 26B-250, the washers 26B-080 and the cable ties 26B-100.
(m) Remove the screw 26B-210, the washer 26B-220 and the clamp 26B-240.
(n) Remove the ami cabin attendant seat-cable 26B-260, the connector backshell
26B-300 and the plug connectors 26B-290, 26B-310.
(p) Remove and disassemble the 2065 VU switch panel 26B-390 as follows:
1 Remove the plugs 26B-500 from the printed circuit board PCB 26B-450.
a Remove the screws 26B-460, the spring washers 26B-470 and the
switch housing 26B-410 from the printed circuit board PCB 26B-450.
4 Remove the switch button-switch 26B-480 from the printed circuit board
PCB 26B-450.
TASK 25-41-58-000-820-D01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-039-A01
D2549010414600
(1) Disassembly of the Electrical System (26C-1)
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables and the cable harness assembly 26C-010 from the
electrical components.
(b) Remove the screws 26C-040, the nuts 26C-050, the smoke detector 26C-020
and the smoke detector sealing 26C-030.
(d) Remove the screws 26C-300, the spacers 26C-290 and the mini inverter
26C-280.
(g) Remove the screws 26C-080, the washers 26C-090 and the bracket 26C-070
from the lavatory structure.
(j) Remove the screws 26C-160, the microswitch 26C-150 and the shrinkable heat
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-040-039-B01
NOTE: It is recommended that you only remove the components if they are
damaged.
For Myanmar Airways (MMA) use only
(a) Disconnect the cables, the bonding straps 26C-200, 26C-210, 26C-240,
26C-250 and the cable harness assembly 26C-010 from the electrical
components.
(b) Remove the nuts 26C-197, 26C-260, the washers 26C-196, 26C-230,
26C–232, 26C-234 and the bonding strap 26C-190, 26C-195.
(c) Remove the screws 26C-040, the nuts 26C-050, the smoke detector 26C-020
and the smoke detector sealing 26C-030.
(e) Remove the screws 26C-300, the spacers 26C-290 and the mini inverter
26C-280.
(h) Remove the screws 26C-080, the washers 26C-090 and the bracket 26C-070
from the lavatory structure.
(j) Remove the screws 26C-160, the microswitch 26C-150 and the shrinkable heat
tubings 26C-170, 26C-180.
(k) Remove the screw 26C-220, the washer 26C-230 and the clamp 26C-270.
SUBTASK 25-41-58-040-039-C01
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26C-200, 26C-210, 26C-240,
26C-250 and the cable harness assembly 26C-010 from the electrical
components.
(b) Remove the nut 26C-260, the washer 26C-230 and the bonding strap 26C-190.
(c) Remove the screws 26C-040, the nuts 26C-050, the smoke detector 26C-020
and the smoke detector sealing 26C-030.
(e) Remove the screws 26C-300, the spacers 26C-290 and the mini inverter
26C-280.
(h) Remove the screws 26C-080, the washers 26C-090 and the bracket 26C-070
from the lavatory structure.
(k) Remove the screws 26C-160, the microswitch 26C-150 and the shrinkable heat
tubings 26C-170, 26C-180.
(l) Remove the screw 26C-220, the washer 26C-230 and the clamp 26C-270.
SUBTASK 25-41-58-040-039-D01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material No.
08-026 Adhe-
sive/Sealant
one Part, RTV
Silicone Rubber
Table 3279
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26C-200, 26C-210, 26C-240,
26C-250 and the cable harness assembly 26C-010 from the electrical
components.
(b) Remove the nut 26C-260, the washer 26C-230 and the bonding strap 26C-190.
(c) Remove the screws 26C-040, the nuts 26C-050, the smoke detector 26C-020
and the smoke detector sealing 26C-030.
(e) Remove the screws 26C-300, the spacers 26C-290 and the mini inverter
26C-280.
(h) Remove the screws 26C-080, the washers 26C-090 and the bracket 26C-070
from the lavatory structure.
(j) Remove the screws 26C-160, the microswitch 26C-150 and the shrinkable heat
tubings 26C-170, 26C-180.
(k) Remove the screw 26C-220, the washer 26C-230 and the clamp 26C-270.
SUBTASK 25-41-58-040-039-E01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material No.
08-026 Adhe-
sive/Sealant
one Part, RTV
Silicone Rubber
Table 3280
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26C-200, 26C-210, 26C-240,
26C-250 and the cable harness assembly 26C-010 from the electrical
components.
(b) Remove the nut 26C-260, the washer 26C-230 and the bonding strap 26C-190.
(c) Remove the screws 26C-040, the nuts 26C-050, the smoke detector 26C-020
and the smoke detector sealing 26C-030.
(e) Remove the screws 26C-300, the spacers 26C-290 and the mini inverter
26C-280.
(h) Remove the screws 26C-080, the washers 26C-090 and the bracket 26C-070
from the lavatory structure.
(k) Remove the screws 26C-160, the microswitch 26C-150 and the shrinkable heat
tubings 26C-170, 26C-180.
(l) Remove the screw 26C-220, the washer 26C-230 and the clamp 26C-270.
SUBTASK 25-41-58-040-039-F01
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26C-200, 26C-210, 26C-240,
26C-250 and the cable harness assembly 26C-010 from the electrical
components.
(b) Remove the nut 26C-260, the washer 26C-230 and the bonding strap 26C-190.
(c) Remove the screws 26C-040, the nuts 26C-050, the smoke detector 26C-020
and the smoke detector sealing 26C-030.
(e) Remove the screws 26C-300, the spacers 26C-290 and the mini inverter
26C-280.
(h) Remove the screws 26C-080, the washers 26C-090 and the bracket 26C-070
from the lavatory structure.
(l) Remove the screws 26C-160, the microswitch 26C-150 and the shrinkable heat
tubings 26C-170, 26C-180.
(m) Remove the screw 26C-220, the washer 26C-230 and the clamp 26C-270.
SUBTASK 25-41-58-040-039-G01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
For Myanmar Airways (MMA) use only
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26C-200, 26C-210, 26C-240,
26C-250 and the cable harness assembly 26C-010 from the electrical
components.
(c) Remove the screws 26C-040, the nuts 26C-050, the smoke detector 26C-020
and the smoke detector sealing 26C-030.
(e) Remove the screws 26C-300, the spacers 26C-290 and the mini inverter
26C-280.
(h) Remove the screws 26C-080, the washers 26C-090 and the bracket 26C-070
from the lavatory structure.
(l) Remove the screws 26C-160, the microswitch 26C-150 and the shrinkable heat
tubings 26C-170, 26C-180.
(m) Remove the screw 26C-220, the washer 26C-230 and the clamp 26C-270.
TASK 25-41-58-000-820-E01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-040-A01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26D-190, 26D-200, 26D-210,
26D-240, 26D-250 and the cable harness assembly 26D-010 from the electrical
components.
(b) Remove the screws 26D-040, the nuts 26D-050, the smoke detector 26D-020
and the smoke detector sealing 26D-030.
(d) Remove the screws 26D-300, the spacers 26D-290 and the mini inverter
26D-280.
(g) Remove the screws 26D-080, the washers 26D-090 and the bracket 26D-070
from the lavatory structure.
(j) Remove the screws 26D-160, the microswitch 26D-150 and the shrinkable heat
tubings 26D-170, 26D-180.
(k) Remove the screw 26D-220, the washer 26D-230 and the clamp 26D-270.
(l) Remove the ami cabin attendant seat-cable 26D-310, the connector backshell
26D-350 and the plug connectors 26D-340, 26D-360.
(m) Remove and disassemble the 2065 VU switch panel 26D-370 as follows:
1 Remove the plugs 26D-480 from the printed circuit board PCB 26D-430.
a Remove the screws 26D-440, the spring washers 26D-450 and the
switch housing 26D-390 from the printed circuit board PCB 26D-430.
4 Remove the switch button-switch 26D-460 from the printed circuit board
PCB 26D-430.
SUBTASK 25-41-58-040-040-B01
D2549030706800 D2549030809600
(0) Disassembly of the Electrical System (26D-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26D-190, 26D-200, 26D-210,
26D-240, 26D-250 and the cable harness assembly 26D-010 from the electrical
components.
(b) Remove the screws 26D-040, the nuts 26D-050, the smoke detector 26D-020
and the smoke detector sealing 26D-030.
(d) Remove the screws 26D-300, the spacers 26D-290 and the mini inverter
26D-280.
(g) Remove the screws 26D-080, the washers 26D-090 and the bracket 26D-070
from the lavatory structure.
(k) Remove the screws 26D-160, the microswitch 26D-150 and the shrinkable heat
tubings 26D-170, 26D-180.
(l) Remove the screw 26D-220, the washer 26D-230 and the clamp 26D-270.
(m) Remove the ami cabin attendant seat-cable 26D-310, the connector backshell
26D-350 and the plug connectors 26D-340, 26D-360.
(n) Remove and disassemble the 2065 VU switch panel 26D-370 as follows:
1 Remove the plugs 26D-480 from the printed circuit board PCB 26D-430.
a Remove the screws 26D-440, the spring washers 26D-450 and the
switch housing 26D-390 from the printed circuit board PCB 26D-430.
4 Remove the switch button-switch 26D-460 from the printed circuit board
PCB 26D-430.
SUBTASK 25-41-58-040-040-C01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
MENT
PART
NAME
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26D-190, 26D-200, 26D-210,
26D-240, 26D-250 and the cable harness assembly 26D-010 from the electrical
components.
(b) Remove the screws 26D-040, the nuts 26D-050, the smoke detector 26D-020
and the smoke detector sealing 26D-030.
(d) Remove the screws 26D-300, the spacers 26D-290 and the mini inverter
26D-280.
For Myanmar Airways (MMA) use only
(g) Remove the screws 26D-080, the washers 26D-090 and the bracket 26D-070
from the lavatory structure.
(j) Remove the screws 26D-160, the microswitch 26D-150 and the shrinkable heat
tubings 26D-170, 26D-180.
(k) Remove the screw 26D-220, the washer 26D-230 and the clamp 26D-270.
(l) Remove the ami cabin attendant seat-cable 26D-310, the connector backshell
26D-350 and the plug connectors 26D-340, 26D-360.
(m) Remove and disassemble the 2065 VU switch panel 26D-370 as follows:
1 Remove the plugs 26D-480 from the printed circuit board PCB 26D-430.
a Remove the screws 26D-440, the spring washers 26D-450 and the
switch housing 26D-390 from the printed circuit board PCB 26D-430.
4 Remove the switch button-switch 26D-460 from the printed circuit board
PCB 26D-430.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-820-F01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-040-041-A01
(1) Disassembly of the Electrical System (26E-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26E-220, 26E-250, 26E-270 and the
cable harness assembly 26E-010 from the electrical components.
(b) Remove the screws 26E-040, the nuts 26E-050, the smoke detector 26E-020
and the smoke detector sealing 26E-030.
(d) Remove the screws 26E-370, the spacers 26E-360 and the mini inverter
26E-350.
(g) Remove the screws 26E-170, the microswitch 26E-160 and the shrinkable heat
tubings 26E-180, 26E-190.
(h) Remove the screw 26E-330, the washer 26E-310, the nut 26E-320 and the
bonding straps 26E-210, 26E-230, 26E-260, 26E-280.
(k) Remove the screw 26E-290, the washer 26E-310 and the clamp 26E-340.
(l) Remove the ami cabin attendant seat-cable 26E-380, the connector backshell
26E-420 and the plug connectors 26E-410, 26E-430.
(m) Remove the screw 26E-330, the washers 26E-300 and the bonding strap
26E-240.
(n) Remove and disassemble the 2065 VU switch panel 26E-460 as follows:
1 Remove the plugs 26E-570 from the printed circuit board PCB 26E-520.
a Remove the screws 26E-530, the spring washers 26E-540 and the
switch housing 26E-480 from the printed circuit board PCB 26E-520.
4 Remove the switch button-switch 26E-550 from the printed circuit board
PCB 26E-520.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-820-G01
D2549030709000
108. Disassembly of the Electrical System
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-040-042-A01
(1) Disassembly of the Electrical System (26F-1)
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26F-190, 26F-220, 26F-240 and the
cable harness assembly 26F-010 from the electrical components.
(b) Remove the screws 26F-040, the nuts 26F-050, the smoke detector 26F-020
and the smoke detector sealing 26F-030.
(d) Remove the screws 26F-080, the washers 26F-090 and the bracket 26F-070
from the lavatory structure.
(e) Remove the screws 26F-440, the spacers 26F-450 and the mini inverter
26F-430.
(h) Remove the screws 26F-080, the washers 26F-090 and the bracket 26F-070
from the lavatory structure.
(k) Remove the screw 26F-300, the washer 26F-280, the nut 26F-290 and the
bonding straps 26F-180, 26F-200, 26F-230, 26F-250.
(l) Remove the screws 26F-080, 26F-320, the washers 26F-090 and the cable
ties 26F-110.
(m) Remove the screw 26F-260, the washer 26F-280 and the clamp 26F-310.
(n) Remove the ami cabin attendant seat-cable 26F-330, the connector backshell
26F-370 and the plug connectors 26F-360, 26F-380.
(p) Remove the screw 26F-300, the washers 26F-270 and the bonding strap
26F-210.
(q) Remove and disassemble the 2065 VU switch panel 26F-460 as follows:
1 Remove the plugs 26F-570 from the printed circuit board PCB 26F-520.
a Remove the screws 26F-530, the spring washers 26F-540 and the
switch housing 26F-480 from the printed circuit board PCB 26F-520.
4 Remove the switch button-switch 26F-550 from the printed circuit board
PCB 26F-520.
For Myanmar Airways (MMA) use only
TASK 25-41-58-000-820-H01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
For Myanmar Airways (MMA) use only
C. Procedure
SUBTASK 25-41-58-040-043-A01
(1) Disassembly of the Electrical System (26G-1)
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26G-200, 26G-210, 26G-220,
26G-250, 26G-260 and the cable harness assembly 26G-010 from the
electrical components.
(b) Remove the screws 26G-040, the nuts 26G-050, the smoke detector 26G-020
and the smoke detector sealing 26G-030.
(d) Remove the screws 26G-310, the spacers 26G-300 and the mini inverter
26G-290.
For Myanmar Airways (MMA) use only
(g) Remove the screws 26G-080, the washers 26G-090 and the bracket 26G-070
from the lavatory structure.
(h) Remove the screws 26G-170, the microswitch 26G-160 and the shrinkable
heat tubings 26G-180, 26G-190.
(l) Remove the screw 26G-230, the washer 26G-240 and the clamp 26G-280.
TASK 25-41-58-000-820-J01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-040-044-A01
D2549026001200
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
No. 08-026
Adhesive/Sealant
one Part, RTV
Silicone Rubber
Table 3287
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26H-190, 26H-200, 26H-210,
26H-240, 26H-250 and the cable harness assembly 26H-010 from the electrical
components.
(b) Remove the screws 26H-265, the washers 26H-091 and the bonding strap
26H-255.
(c) Remove the screws 26H-040, the nuts 26H-050, the smoke detector 26H-020
and the smoke detector sealing 26H-030.
(e) Remove the screws 26H-300, the spacers 26H-290 and the mini inverter
26H-280.
(h) Remove the screws 26H-080, the washers 26H-090 and the bracket 26H-070
from the lavatory structure.
(k) Remove the screws 26H-160, the microswitch 26H-150 and the shrinkable heat
tubings 26H-170, 26H-180.
(l) Remove the screw 26H-220, the washer 26H-230 and the clamp 26H-270.
SUBTASK 25-41-58-040-044-B01
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
More data for bonded parts are given in column SEE REPAIR TASK.
Use the data for the selection of the related repair solution.
801-A01
Material No.
08-026 Adhe-
sive/Sealant
one Part, RTV
Silicone Rubber
Table 3288
REFERENCE LIST FOR THE REPLACEMENT OF PERMANENT
INSTALLED PARTS
NOTE: It is recommended that you only remove the components if they are
damaged.
(a) Disconnect the cables, the bonding straps 26H-190, 26H-200, 26H-210,
26H-240, 26H-250 and the cable harness assembly 26H-010 from the electrical
components.
(b) Remove the screws 26H-040, the nuts 26H-050, the smoke detector 26H-020
and the smoke detector sealing 26H-030.
(d) Remove the screws 26H-300, the spacers 26H-290 and the mini inverter
26H-280.
(g) Remove the screws 26H-080, the washers 26H-090 and the bracket 26H-070
from the lavatory structure.
(j) Remove the screws 26H-160, the microswitch 26H-150 and the shrinkable heat
tubings 26H-170, 26H-180.
(k) Remove the screw 26H-220, the washer 26H-230 and the clamp 26H-270.
TASK 25-41-58-000-820-K01
D2549010300600 R225411623-000
111. Disassembly of the Electrical System
A. General
- Not applicable
B. Procedure
SUBTASK 25-41-58-000-107-A01
(1) Disassembly of the Electrical System
TASK 25-41-58-000-821-A01
A. General
For Myanmar Airways (MMA) use only
– Cleaning
– Visual Inspection
– Replacement of defective parts.
B. Procedure
SUBTASK 25-41-58-040-046-A01
(1) Disassembly of the Cable Harness Assembly (27-1)
NOTE: It is recommended that you only remove the components if they are
damaged.
(b) Remove the screws 27-430, the nuts 27-240, the bracket 27-420, the
identification sleeves 27-110, 27-460, the plugs 27-200, the receptacle
connector 27-400, the connector backshell 27-410, the labels 27-450 and the
cable ties 27-470.
(c) Remove the splices 27-010, the contact pins 27-020, the identification ties
27-030, the socket contacts 27-050, the connector backshell 27-060 and the
plug connector 27-070.
For Myanmar Airways (MMA) use only
(d) Remove the identification ties 27-030, the socket contacts 27-050, the
receptacle connector 27-080, the cable bracket 27-090 and the protective
cap 27-100.
(e) Remove the connector 27-530, the spring latches 27-540, the backshell 27-550
and the socket contacts 27-560.
(f) Remove the receptacle connector 27-080, the cable bracket 27-090, the
protective cap 27-100, the identification sleeves 27-110, the modules 27-160,
27-170, the rail 27-180, the end clamps 27-190 and the plugs 27-200.
(g) Remove the cable terminals 27-120 and the housings 27-130.
(h) Remove the cable terminals 27-140 and the insulations 27-150.
(j) Remove the nuts 27-240, the bracket 27-230, the receptacle connector 27-210
and the connector backshell 27-220.
(k) Remove the cable ties 27-280, the plug connector 27-290 and the connector
backshell 27-300.
TASK 25-41-58-000-821-B01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
B. Procedure
SUBTASK 25-41-58-040-047-A01
NOTE: It is recommended that you only remove the components if they are
damaged.
(b) Remove the screws 27A-550, the nuts 27A-300, the bracket 27A-540, the
identification sleeves 27A-130, 27A-580, the plugs 27A-220, the receptacle
connector 27A-520, the connector backshell 27A-530 and the labels 27A-570.
(c) Remove the splices 27A-010, the contacts 27A-020, the identification ties
27A-030, the socket contacts 27A-050, 27A-330, the connector backshell
27A-060, the plug connector 27A-070, the relay 27A-310, the base 27A-320
and the angle 27A-340.
(d) Remove the identification ties 27A-030, the socket contacts 27A-050, the
connector 27A-080, the spring latches 27A-090, the receptacle connector
27A-100, the cable bracket 27A-110 and the protective cap 27A-120.
(e) Remove the identification sleeves 27A-130, the modules 27A-180, 27A-190,
the end clamps 27A-210 and the plugs 27A-220.
For Myanmar Airways (MMA) use only
(g) Remove the cable terminals 27A-140 and the housings 27A-150.
(h) Remove the cable terminals 27A-160 and the insulations 27A-170.
(k) Remove the nuts 27A-300, the bracket 27A-290 and the connector backshell
27A-280.
(l) Remove the plug 27A-390, the cable ties 27A-400 and the plug connector
27A-410.
SUBTASK 25-41-58-040-047-B01
NOTE: It is recommended that you only remove the components if they are
damaged.
(b) Remove the screws 27A-550, the nuts 27A-300, the bracket 27A-540, the
For Myanmar Airways (MMA) use only
(c) Remove the splices 27A-010, the contacts 27A-020, the identification ties
27A-030, the socket contacts 27A-050, 27A-330, the connector backshell
27A-060, the plug connector 27A-070, the relay 27A-310, the base 27A-320
and the angle 27A-340.
(d) Remove the identification ties 27A-030, the socket contacts 27A-050, the
connector 27A-080, the spring latches 27A-090, the receptacle connector
27A-100, the cable bracket 27A-110 and the protective cap 27A-120.
(e) Remove the identification sleeves 27A-130, the modules 27A-180, 27A-190,
the rail 27A-200, the end clamps 27A-210 and the plugs 27A-220.
(f) Remove the cable terminals 27A-140 and the housings 27A-150.
(g) Remove the cable terminals 27A-160 and the insulations 27A-170.
(j) Remove the nuts 27A-300, the bracket 27A-290, the receptacle connector
27A-270 and the connector backshell 27A-280.
(k) Remove the plug 27A-390, the cable ties 27A-400, the plug connector 27A-410
and the connector backshell 27A-420.
SUBTASK 25-41-58-040-047-C01
D2549010301000 D2549010413800
(0) Disassembly of the Cable Harness Assembly (27A-1)
NOTE: It is recommended that you only remove the components if they are
damaged.
(b) Remove the screws 27A-550, 27A-770, the nuts 27A-300, the bracket 27A-540,
the identification sleeves 27A-130, 27A-580, the plugs 27A-220, the receptacle
connector 27A-520, the connector backshell 27A-530 and the labels 27A-570.
(c) Remove the splices 27A-010, the contacts 27A-020, the identification ties
27A-030, the socket contacts 27A-050, 27A-330, the connector backshell
27A-060, the plug connector 27A-070, the relay 27A-310, the base 27A-320
and the angle 27A-340.
For Myanmar Airways (MMA) use only
(d) Remove the identification ties 27A-030, the socket contacts 27A-050, the
connector 27A-080, the spring latches 27A-090, the receptacle connector
27A-100, the cable bracket 27A-110 and the protective cap 27A-120.
(e) Remove the identification sleeves 27A-130, the modules 27A-180, 27A-190,
the rail 27A-200, the end clamps 27A-210 and the plugs 27A-220.
(f) Remove the cable terminals 27A-140 and the housings 27A-150.
(g) Remove the cable terminals 27A-160 and the insulations 27A-170.
(j) Remove the nuts 27A-300, the bracket 27A-290, the receptacle connector
27A-270 and the connector backshell 27A-280.
(k) Remove the plug 27A-390, the cable ties 27A-400 and the plug connector
27A-410.
TASK 25-41-58-000-822-A01
A. General
– Cleaning
– Visual Inspection
– Replacement of defective parts.
C. Procedure
SUBTASK 25-41-58-040-049-A01
NOTE: It is recommended that you only remove the components if they are
damaged.
For Myanmar Airways (MMA) use only
1 Remove the plug connector 31-020 and the connector backshell 31-030.
3 Remove the coupling screws 31-070, the cable ties 31-040, the receptacle
connector 31-050 and the backshell 31-060.
(b) Remove the screw 31-170, the washer 31-180 and the clamp 31-150 from
the lavatory structure.
(c) Remove the screw 31-170, the washer 31-180 and the clamp 31-160 from
the lavatory structure.
1 Remove the screws 31-240, 31-250 and the rear part of the electric strikes
31-200 from the front part of the electric strikes 31-200.
3 Remove the spring sheets 31-190 and the sheets 31-210, 31-220.
(e) Remove and disassemble the center electric strike 31-270 as follows:
1 Remove the screws 31-240, 31-250 and the rear part of the center electric
strike 31-270 from the front part of the center electric strike 31-270.
3 Remove the spring sheets 31-190 and the sheets 31-210, 31-220.
SUBTASK 25-41-58-040-049-B01
NOTE: It is recommended that you only remove the components if they are
damaged.
1 Remove the plug connector 31-020 and the connector backshell 31-030.
3 Remove the coupling screws 31-070, the cable ties 31-040, the receptacle
connector 31-050 and the backshell 31-060.
(b) Remove the screw 31-170, the washer 31-180 and the clamp 31-150 from
the lavatory structure.
(c) Remove the screw 31-170, the washer 31-180 and the clamp 31-160 from
the lavatory structure.
1 Remove the screws 31-240, 31-250 and the rear part of the electric strike
31-200 from the front part of the electric strike 31-200.
2 Remove the screws 31-240, 31-250, the sub rack assemblies 31-205
and the rear part of the electric strike 31-200 from the front part of the
electric strike 31-200.
4 Remove the spring sheets 31-190 and the sheets 31-210, 31-220.
(e) Remove and disassemble the center electric strike 31-270 as follows:
1 Remove the screws 31-240, 31-250 and the rear part of the center electric
strike 31-270 from the front part of the center electric strike 31-270.
2 Remove the screws 31-240, 31-250, the sub rack assemblies 31-205 and
the rear part of the center electric strike 31-270 from the front part of
the center electric strike 31-270.
4 Remove the spring sheets 31-190 and the sheets 31-210, 31-220.
1 Remove the screws 31-240, 31-250 and the rear part of the electric strike
31-200 from the front part of the electric strike 31-200.
3 Remove the spring sheets 31-190 and the sheets 31-210, 31-220.
SUBTASK 25-41-58-040-049-C01
D2549020307400
(0) Disassembly of the Electrical System of the Cockpit Door Locking (31-1)
NOTE: It is recommended that you only remove the components if they are
damaged.
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
1 Remove the plug connector 31-020 and the connector backshell 31-030.
3 Remove the coupling screws 31-070, the cable ties 31-040, the receptacle
connector 31-050 and the backshell 31-060.
(b) Remove the screw 31-170, the washer 31-180 and the clamp 31-150 from
the lavatory structure.
(c) Remove the screw 31-170, the washer 31-180 and the clamp 31-160 from
the lavatory structure.
1 Remove the screws 31-240, 31-250 and the rear part of the electric strikes
31-200 from the front part of the electric strikes 31-200.
3 Remove the spring sheets 31-190 and the sheets 31-210, 31-220.
(e) Remove and disassemble the center electric strike 31-270 as follows:
1 Remove the screws 31-240, 31-250 and the rear part of the center electric
strike 31-270 from the front part of the center electric strike 31-270.
3 Remove the spring sheets 31-190 and the sheets 31-210, 31-220.
For Myanmar Airways (MMA) use only
1 Remove the screw 31-400, the washers 31-330, 31-360, the nut 31-350,
the spring 31-390 and the CDLS slider 31-290.
3 Remove the screw 31-380, the bushing 31-320, the dead bolt 31-310
and the CDLS slider 31-300.
4 Remove the dead bolt 31-310 from the CDLS slider 31-300.
SUBTASK 25-41-58-040-049-D01
(0) Disassembly of the Electrical System of the Cockpit Door Locking (31-1)
NOTE: It is recommended that you only remove the components if they are
damaged.
NOTE: See TABLE for the references for the replacement procedures of
permanent installed parts.
1 Remove the plug connector 31-020 and the connector backshell 31-030.
3 Remove the coupling screws 31-070, the cable ties 31-040, the receptacle
connector 31-050 and the backshell 31-060.
(b) Remove the screw 31-170, the washer 31-180 and the clamp 31-150 from
the lavatory structure.
(c) Remove the screw 31-170, the washer 31-180 and the clamp 31-160 from
the lavatory structure.
1 Remove the screws 31-240, 31-250 and the rear part of the electric strikes
31-200 from the front part of the electric strikes 31-200.
3 Remove the spring sheets 31-190 and the sheets 31-210, 31-220.
(e) Remove and disassemble the center electric strike 31-270 as follows:
1 Remove the screws 31-240, 31-250 and the rear part of the center electric
strike 31-270 from the front part of the center electric strike 31-270.
3 Remove the spring sheets 31-190 and the sheets 31-210, 31-220.
For Myanmar Airways (MMA) use only
1 Remove the screw 31-400, the washers 31-330, 31-360, the nut 31-350,
the spring 31-390 and the CDLS slider 31-290.
3 Remove the screw 31-380, the bushing 31-320, the dead bolt 31-310
and the CDLS slider 31-300.
4 Remove the dead bolt 31-310 from the CDLS slider 31-300.
CLEANING
TASK 25-41-58-100-807-A01
1. General
TASK 25-41-58-100-801-A01
A. General
REFERENCE DESIGNATION
11-003 Methyl-Ethyl-Ketone
REFERENCE DESIGNATION
vacuum cleaner
C. Procedure
SUBTASK 25-41-58-160-001-A01
(a) Disinfect countertop areas, undersink area and toilet shroud with the Material
No.Material No. 14-001A Deodorant Toilet Non Formaldehyde Base.
(b) Remove all loose dirt with a vacuum cleaner or a soft brush.
(c) Remove all old sealant and dirt with the Material No. 11-003
Methyl-Ethyl-Ketone or with a nonmetallic scraper.
For Myanmar Airways (MMA) use only
TASK 25-41-58-100-802-A01
A. General
REFERENCE DESIGNATION
REFERENCE DESIGNATION
soft brush
C. Procedure
SUBTASK 25-41-58-160-002-A01
(b) Dry all parts with a clean, dry, Material No. 19-003 Lint-Free Cotton Cloth or
a hot-air blower.
TASK 25-41-58-100-803-A01
A. General
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-160-003-A01
(a) Clean all stainless steel parts with Material No. 11-016 Safety Solvent.
TASK 25-41-58-100-804-A01
A. General
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-160-004-A01
(a) Lightly clean all electrical parts which you can get access to with a soft
nonmetallic brush.
(b) Blow loose dust and dirt from all parts with dry, filtered air.
(c) Clean the surfaces of the electrical units with a clean, Material No. 19-003
Lint-Free Cotton Cloth or a soft bristle brush moist with Material No. 11-010
For Myanmar Airways (MMA) use only
TASK 25-41-58-100-805-A01
A. General
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-160-005-A01
(a) Flush the full installation system with a solution of Material No.14-001A
Deodorant Toilet Non Formaldehyde Base or an equivalent, and distilled water.
(b) Flush the full installation system with fresh potable water.
(c) Use clean, dry compressed air to blow out and dry parts.
TASK 25-41-58-100-806-A01
A. General
REFERENCE DESIGNATION
11-003 Methyl-Ethyl-Ketone
C. Procedure
SUBTASK 25-41-58-160-006-A01
(b) After using a Material No. 11-003 Methyl-Ethyl-Ketone protect the surface with
the Material No. 04-012 Pure Mineral Vaseline or Petro-Latum.
For Myanmar Airways (MMA) use only
INSPECTION/CHECK
TASK 25-41-58-200-813-A01
1. General
TASK 25-41-58-200-801-A01
A. General
C. Procedure
SUBTASK 25-41-58-210-001-A01
TASK 25-41-58-200-802-A01
A. General
C. Procedure
SUBTASK 25-41-58-210-002-A01
(a) Examine the sandwich panels and the doors for deformation, cracks, holes
and delamination.
(b) Examine the lower area of the lavatory wall for corrosion. Up to a max. height
of 400 mm (15.748 in.) you can repair the wall. If this area is higher change
the complete wall.
(c) Examine the lower aluminium attachment fittings from the lavatory walls for
corrosion and damage.
TASK 25-41-58-200-803-A01
A. General
C. Procedure
SUBTASK 25-41-58-210-003-A01
(a) Examine the threaded inserts for correct installation and condition of the thread.
TASK 25-41-58-200-804-A01
A. General
C. Procedure
SUBTASK 25-41-58-210-004-A01
TASK 25-41-58-200-805-A01
A. General
C. Procedure
SUBTASK 25-41-58-210-005-A01
(a) Examine the upper and the lower attachment fittings for cracks, loose fit and
damaged holes.
1 If any upper or lower attachment fitting shows any signs of damage you
must replace it.
TASK 25-41-58-200-806-A01
A. General
C. Procedure
SUBTASK 25-41-58-210-006-A01
(a) Examine the sealing strips for wear, correct fit and alignment.
TASK 25-41-58-200-807-A01
A. General
C. Procedure
SUBTASK 25-41-58-210-007-A01
TASK 25-41-58-200-808-A01
A. General
C. Procedure
SUBTASK 25-41-58-210-008-A01
(a) Examine the attachment and the condition of the air vent.
(b) Make sure that the opening of the air vent is clean.
TASK 25-41-58-200-809-A01
A. General
C. Procedure
SUBTASK 25-41-58-210-009-A01
(a) Examine the correct operation of the latches and the fasteners.
(b) Make sure that the latches and the fasteners are clean.
TASK 25-41-58-200-810-A01
A. General
C. Procedure
SUBTASK 25-41-58-210-010-A01
TASK 25-41-58-200-811-A01
A. General
C. Procedure
SUBTASK 25-41-58-210-011-A01
(a) Examine the clamps and the supports for attachment and damage.
(b) Examine the hoses, the tubes, the fittings and the hose connections for
attachment, damage and leaks.
(c) Examine the hoses and the gaskets and/or O-rings for signs of ageing.
TASK 25-41-58-200-812-A01
A. General
C. Procedure
SUBTASK 25-41-58-210-012-A01
(c) Examine the plugs and the receptacles and make sure that there are no pins
loose, broken or missing.
(d) Examine the terminal lugs for firm connection to the wire ends.
(e) Examine connections on terminal boards and ground studs for corrosion.
(g) Examine the lavatory light lens for damage and presence.
REPAIR
TASK 25-41-58-350-804-A01
1. General
REPAIR
Page 6001
25-41-58 Apr 30/15
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-350-804-A01
2. Materials
A. Decorative Foils
REPAIR
Page 6002
25-41-58 Sep 30/17
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
REPAIR
Page 6003
25-41-58 Sep 30/17
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
B. Paint
DESCRIP-
PART NO. WHERE USED
TION
REPAIR
Page 6004
25-41-58 Sep 30/17
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
DESCRIP-
PART NO. WHERE USED
TION
R225401689-018)
Air extraction grille
(R225401689-008,
R225401689-010,
R225401689-012,
R225401689-014,
R225401689-016,
R225401689-018)
Nursing table (R225401689-
008, R225401689-010,
R225401689-012,
R225401689-014,
R225401689-016,
For Myanmar Airways (MMA) use only
R225401689-018)
Nursing table hook
(R225401689-008,
R225401689-010,
R225401689-012,
R225401689-014,
R225401689-016,
R225401689-018)
Water cup dispenser
(R225401689-008,
R225401689-010,
R225401689-012,
R225401689-014,
R225401689-016,
R225401689-018)
Service cabinet (R225401689-
008, R225401689-010,
R225401689-012,
R225401689-014,
R225401689-016,
R225401689-018)
Toilet seat assy (R225401689-
008, R225401689-010,
R225401689-012,
R225401689-014,
R225401689-016,
R225401689-018)
REPAIR
Page 6005
25-41-58 Sep 30/17
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
DESCRIP-
PART NO. WHERE USED
TION
Unit cover (R225401689-008,
R225401689-010,
R225401689-012,
R225401689-014,
R225401689-016,
R225401689-018)
Bracket (R225401689-008,
R225401689-010,
R225401689-012,
R225401689-014,
R225401689-016,
R225401689-018)
Housing (R225401689-008,
For Myanmar Airways (MMA) use only
R225401689-010,
R225401689-012,
R225401689-014,
R225401689-016,
R225401689-018)
REPAIR
Page 6006
25-41-58 Sep 30/17
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
DESCRIP-
PART NO. WHERE USED
TION
(D2549010301000)
Service Box (D2549010301000)
Spacer (D2549010301000)
Air extraction grille
(D2549010301000)
REPAIR
Page 6007
25-41-58 Sep 30/17
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
DESCRIP-
PART NO. WHERE USED
TION
R225401196-072,
R225401196-074,
R225401196-076,
R225401196-078)
Rear wall (D2549010301000,
R225401196-072,
R225401196-074,
R225401196-076,
R225401196-078)
Louver (D2549010301000,
R225401196-072,
R225401196-074,
R225401196-076,
R225401196-078)
Service cabinet assy
(D2549010301000,
R225401196-072,
R225401196-074,
R225401196-076,
R225401196-078)
Service box assy
(D2549010301000,
R225401196-072,
R225401196-074,
R225401196-076,
R225401196-078)
Oxygen container cover
(D2549010301000,
REPAIR
Page 6008
25-41-58 Sep 30/17
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
DESCRIP-
PART NO. WHERE USED
TION
R225401196-072,
R225401196-074,
R225401196-076,
R225401196-078)
Toilet seat cover dispenser
(D2549010301000,
R225401196-072,
R225401196-074,
R225401196-076,
R225401196-078)
Flap (D2549010301000,
R225401196-072,
R225401196-074,
For Myanmar Airways (MMA) use only
R225401196-076,
R225401196-078)
Hook assy (D2549010301000,
R225401196-072,
R225401196-074,
R225401196-076,
R225401196-078)
Nursing table assy
(D2549010301000,
R225401196-072,
R225401196-074,
R225401196-076,
R225401196-078)
Spacer (D2549010301000,
R225401196-072,
R225401196-074,
R225401196-076,
R225401196-078)
REPAIR
Page 6009
25-41-58 Sep 30/17
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
DESCRIP-
PART NO. WHERE USED
TION
(D2549010411000,
D2549010413800)
Spacer (D2549010411000,
D2549010413800)
Service Box (D2549010411000,
D2549010413800)
Air extraction grille
(D2549010411000,
D2549010413800)
REPAIR
Page 6010
25-41-58 Sep 30/17
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
DESCRIP-
PART NO. WHERE USED
TION
R225401862-004,
R225401862-006)
Support bracket (R225401839-
000, R225401839-002,
R225401862-000,
R225401862-002,
R225401862-004,
R225401862-006)
Toilet shroud assy
(R225401839-000,
R225401839-002,
R225401862-000,
R225401862-002,
For Myanmar Airways (MMA) use only
R225401862-004,
R225401862-006)
REPAIR
Page 6011
25-41-58 Sep 30/17
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-300-802-A01
A. General
(1) For the rivet replacement refer to the standard riveting procedure.
REFERENCE DESIGNATION
05-056 Glasscloth
11-520 Ethanol
LN9073-3.3214T4-1.2
REFERENCE DESIGNATION
milling cutter
REPAIR
Page 6012
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
C. Procedure
SUBTASK 25-41-58-350-002-A01
1 Install the NTF-covering with the Material No. 08-082 Acrylic Pressure
Sensitive Adhesive Film to the floor pan.
2 Seal the edges of the NTF-covering with the Material No. 08-026
Adhesive/Sealant one Part, RTV Silicone Rubber.
SUBTASK 25-41-58-350-003-A01
(1) Repair of Cracks or Damages in the Floor Bottom (around the NTF-covering,
underneath the NTF-covering, behind the toilet shroud and underneath the
REPAIR
Page 6013
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
washbasin)
(a) Drill a hole with a diameter of 3.5 mm (0.138 in) at each end of the crack.
(b) Remove the damage with a milling cutter and / or a drill (see FIGURE
25-41-58-991-006-A).
(c) Make the repair area smooth with the abrasive paper, 320 - 400 grade of grain.
(e) Fill the prepared area with the Material No. 08-025 Two Component
Polyurethane Adhesive.
(f) Let the Material No. 08-025 Two Component Polyurethane Adhesive cure
for 1 hour.
(g) Install one layer of laminate made from the Material No. 05-056 Glasscloth
and the Material No. 08-001 General Purpose Adhesive Honeycomb Filler
on both sides.
(h) If necessary, make the repair area smooth with the abrasive paper, 320 - 400
grade of grain.
REPAIR
Page 6014
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(k) Apply the Material No. 16-047 Decorative Paint (Internal Applic.) to the repair
area.
SUBTASK 25-41-58-350-004-A01
(1) Repair of Cracks or Damages in the Vertical Panel of the Floor Pan
(a) Drill a hole with a diameter of 3.5 mm (0.138 in) at each end of the crack.
(b) Remove the damage with a milling cutter and / or a drill (see FIGURE
For Myanmar Airways (MMA) use only
25-41-58-991-007-A).
(c) Clean the repair area with the Material No. 11-520 Ethanol.
(d) Fill the prepared area with the Material No. 08-025 Two Component
Polyurethane Adhesive.
(e) Make a stiffener from the Material No. 05-109 Laminate, A/C Interior (see
FIGURE 25-41-58-991-007-A).
(f) Bond the stiffener with the Material No. 08-025 Two Component Polyurethane
Adhesive to the repair area.
(g) If necessary, make the repair area smooth with the abrasive paper, 320 - 400
grade of grain.
REPAIR
Page 6015
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(j) Apply the Material No. 16-047 Decorative Paint (Internal Applic.) to the repair
area.
SUBTASK 25-41-58-350-005-A01
(b) Make pads 50 mm (1.969 in) x 50 mm (1.969 in) from the Material No. 05-109
Laminate, A/C Interior or polycarbonat plates DAN 197/198 or similar.
(c) Bond the pads with the Material No. 08-017A Adhesive Structuralflexible to
the floor pan.
(d) Apply the Material No. 16-047 Decorative Paint (Internal Applic.) to the repair
area.
SUBTASK 25-41-58-350-006-A01
REPAIR
Page 6016
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(a) If necessary, remove the old damaged sealant with a non-metallic scraper.
(b) Clean the repair area with the Material No. 11-520 Ethanol.
(c) Apply a new seam with the Material No. 08-026 Adhesive/Sealant one Part,
RTV Silicone Rubber to the prepared area.
(d) If necessary, make the sealing seam smooth with a spatula or another
applicable tool.
SUBTASK 25-41-58-380-001-A01
For Myanmar Airways (MMA) use only
(b) Clean the repair area with the Material No. 11-520 Ethanol.
(c) Fill the scratches with the Material No. 08-036 Polyester Filler.
(d) Apply the Material No. 16-047 Decorative Paint (Internal Applic.) to the repair
area.
SUBTASK 25-41-58-350-007-A01
NOTE: A repair is not possible and the floor pan must be replaced, if
– the crack is longer than 710 mm (27.953 in)
– 2 cracks at less than 51 mm (2.008 in) from each other
– the cracks occur like shown in FIGURE 25-41-58-991-008-A.
REPAIR
Page 6017
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
SUBTASK 25-41-58-350-008-A01
(1) Replacement of the Damaged Floor Pan Inserts (for toilet unit fixation)
For Myanmar Airways (MMA) use only
(c) Enlarge the hole up to a diameter of 17.4 mm (0.685 in) (see FIGURE
25-41-58-991-011-A).
(d) Clean the repair area with the Material No. 11-520 Ethanol.
(e) Bond the repair insert NAS1833C4-370 with the Material No. 08-017A
Adhesive Structuralflexible to the enlarged hole.
REPAIR
Page 6018
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
SUBTASK 25-41-58-350-009-A01
Table 6005
REPLACEMENT PART
(b) Remove the damaged floor pan inserts and the damaged areas.
(c) Clean the repair area with the Material No. 11-520 Ethanol.
(d) Fill the prepared area with the Material No. 08-017A Adhesive Structuralflexible
(see FIGURE 25-41-58-991-012-A).
(e) Make a stiffener from the Material No. 05-109 Laminate, A/C Interior or similar
(see FIGURE 25-41-58-991-013-A).
(f) Bond the stiffener with the Material No. 08-017A Adhesive Structuralflexible to
the repair area (see FIGURE 25-41-58-991-013-A).
(g) Bond the repair insert NAS 1833C4-370 with the Material No. 08-017A
Adhesive Structuralflexible to the stiffener.
REPAIR
Page 6019
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
SUBTASK 25-41-58-350-010-A01
Clipnuts AR MS21061-08
(b) Make the repair area smooth with the abrasive paper, 320 - 400 grade of grain.
(c) Clean the repair area with the Material No. 11-520 Ethanol.
(d) Make a metal sheet from the Material No. LN9073-3.3214T4-1.2 (see FIGURE
25-41-58-991-046-A).
(e) Install the clipnuts MS21061-08 with the countersunk rivets LN9199-2406G to
the sheet (see FIGURE 25-41-58-991-046-A).
(f) Bond the sheet with the Material No. 08-001 General Purpose Adhesive
Honeycomb Filler to the floor pan (see FIGURE 25-41-58-991-046-A).
REPAIR
Page 6020
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6021
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6022
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6023
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6024
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6025
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6026
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
Damaged Area
Figure 6007/EN254158GRAPHIC991012A01
REPAIR
Page 6027
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6028
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6029
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-300-806-A01
A. General
NOTE: Material No. 08-017 Bonding Metal/Metal is operator supplied and not part
of the kit.
NOTE: For the repair procedure of the subcomponents refer to the supplier's
manuals (refer to (Refer to TASK )TASK 25-41-58-870-802-A01).
NOTE: Do not use KETONE or ACETONE for the cleaning of these parts after the
repair:
– the floor pan,
– the service cabinet,
– the seat cover dispenser,
– the toilet shrouds with the supports,
– the air grids,
– all the parts made of poly carbonate.
Cover these parts if you work with KETONE or ACETONE to prevent of
moist.
Use only ETHANOL (Material. No. 11-520) to clean the parts made of
poly-carbonate.
REPAIR
Page 6030
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
– the screws of lower and upper attachments and all selflocking nuts,
– all the seals,
– all the bulbs and the fluorescent tubes.
(2) For the rivet replacement refer to the standard riveting procedure.
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-350-013-A01
(b) Clean the bonding area with Material No. 11-010 Isopropyl Alcohol and bond
the new sealing profile with Material No. 08-026 Adhesive/Sealant one Part,
RTV Silicone Rubber.
REPAIR
Page 6031
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-300-809-A01
A. General
NOTE: Material No. 08-017 Bonding Metal/Metal is operator supplied and not part
of the kit.
NOTE: For the repair procedure of the subcomponents refer to the supplier's
manuals (refer to (Refer to TASK )TASK 25-41-58-870-802-A01).
NOTE: Do not use KETONE or ACETONE for the cleaning of these parts after the
repair:
– the floor pan,
– the service cabinet,
– the seat cover dispenser,
– the toilet shrouds with the supports,
– the air grids,
– all the parts made of poly carbonate.
Cover these parts if you work with KETONE or ACETONE to prevent of
moist.
Use only ETHANOL (Material. No. 11-520) to clean the parts made of
poly-carbonate.
REPAIR
Page 6032
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
– the screws of lower and upper attachments and all selflocking nuts,
– all the seals,
– all the bulbs and the fluorescent tubes.
(2) For the rivet replacement refer to the standard riveting procedure.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
abrasive paper
C. Procedure
SUBTASK 25-41-58-320-001-A01
(a) Remove the scratches up to a depth of 0.3 mm (0.0118 in.) with the abrasive
paper. The grade of grain of the abrasive paper depends on the depth of the
scratches. Use step by step the next higher grade of grain.
(c) Use Material No. 19-011 Scotch Brite Pads and the Material No. 04-012 Pure
Mineral Vaseline or Petro-Latum to have the brightness of the undamaged
areas for the working area.
REPAIR
Page 6033
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(d) Protect the surface with Material No. 04-012 Pure Mineral Vaseline or
Petro-Latum.
SUBTASK 25-41-58-320-002-A01
NOTE: When ordering the repairing compound, state the sheet and/or the
moulded piece number (red label) and the colour code (yellow label)
and/or send in a sample of the sheet when possible. This information
is necessary for align the colour in the factory. In the event that you
will send the sample of the sheet, clean the unit and the sample by wet
For Myanmar Airways (MMA) use only
grinding them with the abrasive paper (400 grade of grain) and check
them for colour sameness in a wet state at the same level.
(a) Mill out the crack with 3 (0.118 in.) to 4 mm (0.157 in.) wide milling cutter (refer
to FIGURE 25-41-58-991-014-A, figure 610A). Open not easily accessible
spots with a handmilling machine, make smooth with a chisel. We recommend
to make one or several additional transverse grooves for the parts subject
to high mechanical stresses. Put a reinforcement (e.g. M5 X 150 mm
long threaded rod, M5 = min. Ø) into the bottom adhesive compound of
the transverse groove to repair the longitudinal cracks (refer to FIGURE
25-41-58-991-014-A, figure 610B).
(b) Fill in the bottom of the groove amply with the matching coloured
Material No. 08-103 Repair Kit for Washbasin adhesive (refer to FIGURE
25-41-58-991-014-A, figure 610C). For the dosing quantity see. Fill the vertical
joints section by section with the aid of pockets made of the adhesive tape or
the clamps (refer to FIGURE 25-41-58-991-014-A, figure 610D).
(c) Remove the ridge of the adhesive with a chisel, approximately 20 minutes after
set. Depth 2 mm (0.078 in.) to 3 mm (0.118 in.), width a little bit wider than
the groove (refer to FIGURE 25-41-58-991-014-A, figure 610E). At not easily
accessible spots, expose the groove with a sharp blade. Carefully scrape the
REPAIR
Page 6034
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
edges of the groove. Make smooth the top edges of the groove with a fine
sanding paper (grade of grain 180-240). Remove the loose remaining.
(d) Fill the remaining groove with the Material No. 08-103 Repair Kit for
Washbasin repairing compound. For dosing quantity see. Ridge prevents
colour faults caused by the reaction with the air humidity (refer to FIGURE
25-41-58-991-014-A, figure 610F).
(e) Remove the air out of the repairing compound. Hit it or use a tooth pick for
running all around the edges of the groove.
(f) After hardening for min. 24 hours at min. 20°C (68°F), grind the ridge and
match the gloss of the surface as given (Refer to SUBTASK )SUBTASK
For Myanmar Airways (MMA) use only
25-41-58-320-001-A01.
SUBTASK 25-41-58-350-015-A01
NOTE: The length of the tube hardener pressed from the tube is the
measure for the dosing.
REPAIR
Page 6035
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
NOTE: The length of the tube hardener pressed from the tube is the
measure for the dosing.
SUBTASK 25-41-58-350-016-A01
(a) Contrast colour is supplied with aquarell colours to match colours on site. Fill
For Myanmar Airways (MMA) use only
the groove with repairing compound without any contrast colours. Immediately
afterwards, add a few drops of contrast colour to the repairing compound +
Hardener B Materail No. 08-103 Repair Kit for Washbasin mixture.
(b) Mix the compound and restore marbling on site with a tooth pick.
REPAIR
Page 6036
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6037
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-300-813-A01
A. General
NOTE: Material No. 08-017 Bonding Metal/Metal is operator supplied and not part
of the kit.
NOTE: For the repair procedure of the subcomponents refer to the supplier's
manuals (refer to (Refer to TASK )TASK 25-41-58-870-802-A01).
NOTE: Do not use KETONE or ACETONE for the cleaning of these parts after the
repair:
– the floor pan,
– the service cabinet,
– the seat cover dispenser,
– the toilet shrouds with the supports,
– the air grids,
– all the parts made of poly carbonate.
Cover these parts if you work with KETONE or ACETONE to prevent of
moist.
Use only ETHANOL (Material. No. 11-520) to clean the parts made of
poly-carbonate.
REPAIR
Page 6038
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
– the screws of lower and upper attachments and all selflocking nuts,
– all the seals,
– all the bulbs and the fluorescent tubes.
(2) For the rivet replacement refer to the standard riveting procedure.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-320-003-A01
(a) Remove the cracked ring cover from the toilet shroud.
REPAIR
Page 6039
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(b) Use the abrasive paper, 320-400 grade of grain, to remove the remaining
adhesive.
(c) Clean the bonding area with the CLEANING AGENT ETHANOL (Material No.
11-520).
SUBTASK 25-41-58-380-004-A01
(a) Bond the ring cover to the toilet shroud with Material No. 08-017 Bonding
Metal/Metal.
For Myanmar Airways (MMA) use only
NOTE: Make sure that the both surfaces are placed correct, before you
apply the adhesive.
(b) Fill the visible areas with Material No. 08-036 Polyester Filler.
(c) Smooth the bonding area with the abrasive paper, 320-400 grade of grain.
SUBTASK 25-41-58-350-020-A01
(c) Clean the repair and smooth the area of stiffener with the abrasive paper,
320-400 grade of grain.
(d) Fill the damaged area with Material No. 08-025 Two Component Polyurethane
Adhesive.
REPAIR
Page 6040
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(e) Let the Material No. 08-025 Two Component Polyurethane Adhesive cure
for 1 hour.
(f) Install 2 laminates made from LN9169-8-4548-6 GLASS FABRIC with Material
No. 08-001 General Purpose Adhesive Honeycomb Filler on both sides of the
shroud (refer to FIGURE 25-41-58-991-017-A).
(g) If necessary, smooth the repair with abrasive paper, 320-400 grade of grain and
apply a colour layer of Material No. 16-047 Decorative Paint (Internal Applic.).
SUBTASK 25-41-58-350-021-A01
(1) Repair of Cracks or Damages in the Area of the Fixing Holes of the Cover
(d) Fill the damaged area with the Material No. 08-025 Two Component
Polyurethane Adhesive.
REPAIR
Page 6041
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(e) Let the 08-025 Two Component Polyurethane Adhesive cure for 1 hour.
(f) Make a stiffener from a laminate LN40606B020 cloth plate or similar (refer to
FIGURE 25-41-58-991-018-A).
(g) Bond the stiffener to the repair area from the rear/ back side with the Material
No. 08-025 Two Component Polyurethane Adhesive.
(h) If necessary, smooth the repair with abrasive paper, 320-400 grade of grain
and apply a color layer of the Material No. 16-047 Decorative Paint (Internal
Applic.).
(j) Drill new holes diameter 10 mm (0.394 in.) for the installation of the toilet cover.
SUBTASK 25-41-58-350-022-A01
(1) Repair of Cracks or Damages in the Area of the Lower Attachment Holes
(c) Clean the repair and smooth the area of stiffener with the abrasive paper,
320-400 grade of grain.
(d) Fill the damaged area and the existing hole with Material No. 08-025 Two
Component Polyurethane Adhesive.
REPAIR
Page 6042
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(e) Let the 08-025 Two Component Polyurethane Adhesive cure for 1 hour.
(f) Install 2 laminates made from LN9169-8-4548-6 GLASS FABRIC with Material
No. 08-001 General Purpose Adhesive Honeycomb Filler on both sides of the
shroud (refer to FIGURE 25-41-58-991-017-A).
(g) Drill a new countersunk hole and bond a washer P/N NAS1169DD8 to it with
the Material No. 08-025 Two Component Polyurethane Adhesive (refer to
For Myanmar Airways (MMA) use only
(h) If necessary, smooth the repair with abrasive paper, 320-400 grade of grain and
apply a color layer of Material No. 16-047 Decorative Paint (Internal Applic.).
REPAIR
Page 6043
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6044
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6045
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6046
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6047
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-300-814-A01
A. General
NOTE: Material No. 08-017 Bonding Metal/Metal is operator supplied and not part
of the kit.
NOTE: For the repair procedure of the subcomponents refer to the supplier's
manuals (refer to (Refer to TASK )TASK 25-41-58-870-802-A01).
NOTE: Do not use KETONE or ACETONE for the cleaning of these parts after the
repair:
– the floor pan,
– the service cabinet,
– the seat cover dispenser,
– the toilet shrouds with the supports,
– the air grids,
– all the parts made of poly carbonate.
Cover these parts if you work with KETONE or ACETONE to prevent of
moist.
Use only ETHANOL (Material. No. 11-520) to clean the parts made of
poly-carbonate.
REPAIR
Page 6048
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
– the screws of lower and upper attachments and all selflocking nuts,
– all the seals,
– all the bulbs and the fluorescent tubes.
(2) For the rivet replacement refer to the standard riveting procedure.
REFERENCE DESIGNATION
1 Covering A2 25491004-216
For Myanmar Airways (MMA) use only
2 Covering A2 25491004-214
3 Covering A2 25491004-204
4 Covering A2 25491004-202
5 Stiffening A2 25491004-228
6 Stiffening A2 25491004-226
8 Covering A2 25491004-220
9 Covering A2 25491004-218
10 Covering A2 25491004-224
11 Covering A2 25491004-222
12 Stiffening A2 25491004-208
13 Stiffening A2 25491004-206
REPAIR
Page 6049
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-350-023-A01
NOTE: Brackets with damages or corrosion less than 250 mm (9.843 in.)
remain installed.
(a) Remove the stiffening (Aluminium sheet), the covering (Aluminium sheet) and
the corroded ALU-bracket. Prepare cut out for the new brackets (refer to
FIGURE 25-41-58-991-021-A).
(b) Remove and reuse the screws (30, 33, 35) and the fittings (20, 21, 25) (refer
to IPL_FIGURE_06).
(c) Make the repair section rough with the abrasive paper, 320-400 grade of grain
(d) Clean the repair area with the Material No. Cleaning agent (11-583) and
Material No. 19-003 Lint-Free Cotton Cloth.
NOTE: Check the lavatory wall and the core for damages. If the
core is damaged repair per (Refer to SUBTASK )SUBTASK
25-41-58-350-024-A01.
REPAIR
Page 6050
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
NOTE: For the vendor codes and the optional numbers see the
corresponding IPL_FIGURE_06.
(f) Install the new brackets (13) and the new bracket (17) with the Material
No. 08-017 Bonding Metal/Metal. Fill the core around the new bracket
approximately 20 mm (0.787 in.).
(g) Install the inside and the outside covering (refer to FIGURE 25-41-58-991-021-A,
FIGURE 25-41-58-991-023-A, FIGURE 25-41-58-991-024-A and JOB SETUP
INFORMATION) with the Material No. 08-017 Bonding Metal/Metal.
NOTE: For the change of one or two brackets take the inside and
the outside covering of the appropriate size (refer to FIGURE
25-41-58-991-024-A).
(h) Install the inside and the outside stiffening (refer to FIGURE
25-41-58-991-021-A, FIGURE 25-41-58-991-023-A, FIGURE
25-41-58-991-025-A and JOB SETUP INFORMATION) with the Material No.
08-017 Bonding Metal/Metal.
NOTE: For the change of one or two brackets take the inside and
the outside stiffening of the appropriate size (refer to FIGURE
25-41-58-991-026-A).
(j) Install the fittings (20, 21, 25) with the screws (30, 33, 35) (refer to
IPL_FIGURE_06).
REPAIR
Page 6051
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(k) Align the laminated plastic (refer to JOB SETUP INFORMATION Item 15) and
install it with the Material No. 08-017 Bonding Metal/Metal on the bottom of
the wall.
(l) Smooth the repair area with the abrasive paper, 320-340 grade of grain.
SUBTASK 25-41-58-350-024-A01
(1) Repair of the Corroded Honeycomb Core and of the Damaged Brackets (06–1)
For Myanmar Airways (MMA) use only
NOTE: Brackets with damages or corrosion less than 250 mm (9.843 in.)
remain installed.
(a) Remove the stiffening (Aluminum sheet), the covering (Aluminum sheet) and
the corroded ALU-bracket of the damaged area from both sides of the lavatory
wall.
(b) Remove and reuse the screws (30, 33, 35)) and the fittings (20, 21, 25).
(d) Make the repair section rough with the abrasive paper, 320-340 grade of grain.
(e) Clean the repair area with the Material No. Cleaning agent (11-583) and a
Material No. 19-003 Lint-Free Cotton Cloth.
NOTE: For the vendor codes and the optional numbers see the
corresponding IPL_FIGURE_06.
REPAIR
Page 6052
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(g) Align and install the new honeycomb core with the cut out for the new bracket
with Material No. 08-017 Bonding Metal/Metal. Fill the core dividing area with
Material No. 08-017 Bonding Metal/Metal, width 20 mm (0.787 in.).
(h) Install the new brackets (13) and the new bracket (17) with the Material
No. 08-017 Bonding Metal/Metal. Fill the core around the new bracket
approximately 20 mm (0.787 in.).
For Myanmar Airways (MMA) use only
NOTE: For the change of one or two brackets take the inside covering of
the appropriate size (refer to FIGURE 25-41-58-991-030-A).
NOTE: For the change of one or two brackets take the outside covering
of the appropriate size (refer to FIGURE 25-41-58-991-030-A).
(l) Install the inside and outside stiffening (refer to FIGURE 25-41-58-991-027-A,
FIGURE 25-41-58-991-029-A, FIGURE 25-41-58-991-025-A and JOB SETUP
REPAIR
Page 6053
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
NOTE: For the change of one or two brackets take the stiffening of the
appropriate size (refer to FIGURE 25-41-58-991-025-A).
(m) Install the fittings (20, 21, 25) with the screws (30, 33, 35) (refer to
IPL_FIGURE_06).
(n) Align the laminated plastic (refer to JOB SETUP INFORMATION, Item 15) and
install it with the Material No. 08-017 Bonding Metal/Metal on the bottom of
the wall.
For Myanmar Airways (MMA) use only
(p) Smooth the repair area with the abrasive paper, 320-340 grade of grain.
NOTE: The corroded area of the damaged wall must not exceed
more than 400 mm (15.748 in.). If this area is higher than 400
mm (15.748 in.) change the complete wall (refer to FIGURE
25-41-58-991-031-A).
REPAIR
Page 6054
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6055
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6056
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6057
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6058
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6059
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6060
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6061
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6062
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6063
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6064
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6065
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6066
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-300-815-A01
A. General
NOTE: Material No. 08-017 Bonding Metal/Metal is operator supplied and not part
of the kit.
NOTE: For the repair procedure of the subcomponents refer to the supplier's
manuals (refer to (Refer to TASK )TASK 25-41-58-870-802-A01).
NOTE: Do not use KETONE or ACETONE for the cleaning of these parts after the
repair:
– the floor pan,
– the service cabinet,
– the seat cover dispenser,
– the toilet shrouds with the supports,
– the air grids,
– all the parts made of poly carbonate.
Cover these parts if you work with KETONE or ACETONE to prevent of
moist.
Use only ETHANOL (Material. No. 11-520) to clean the parts made of
poly-carbonate.
REPAIR
Page 6067
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
– the screws of lower and upper attachments and all selflocking nuts,
– all the seals,
– all the bulbs and the fluorescent tubes.
(2) For the rivet replacement refer to the standard riveting procedure.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-350-025-A01
(b) Cut off the damaged lower part of the wall max. 400 mm (15.748 in.) (refer to
FIGURE 25-41-58-991-032-A).
(c) Remove 20 mm (0.787 in.) of the honeycomb from the inside of the aluminum
wall, between the aluminum sheets to install the composite repair panel to the
REPAIR
Page 6068
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(d) Check the inserts and replace if necessary. Drill holes with a diameter 14.3
mm (0.563 in.) and a depth of 10.4 mm (0.409 in.). Take location from the
existing inserts.
(e) Clean the repair area with the Material No. Cleaning agent (11-583) and
Material No. 19-003 Lint-Free Cotton Cloth.
(f) Install the composite repair panel with the Material No. 08-017 Bonding
Metal/Metal and supply it with reinforcements max. 100 mm (3.934
in.) completely (refer to FIGURE 25-41-58-991-034-A, FIGURE
For Myanmar Airways (MMA) use only
(g) Make a cut out for the support brackets of the toilet shroud assembly on
the lavatory inside wall (refer to FIGURE 25-41-58-991-032-A and FIGURE
25-41-58-991-037-A).
(h) Use the cable duct according to the damaged wall (refer to FIGURE
25-41-58-991-032-A).
(l) Make a cut outs (if must agree with the customer option) (refer to FIGURE
25-41-58-991-039-A).
(m) Close the honeycomb with the Material No. 08-022 Compound, Void Filler Low
Density (refer to FIGURE 25-41-58-991-039-A).
(n) Smooth the repair area with the abrasive paper, 320-400 grade of grain.
(p) Install the decor film. Type and color depends on customer requirement, see
existing wall.
REPAIR
Page 6069
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6070
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6071
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6072
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6073
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6074
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6075
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6076
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6077
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-300-816-A01
A. General
NOTE: Material No. 08-017 Bonding Metal/Metal is operator supplied and not part
of the kit.
NOTE: For the repair procedure of the subcomponents refer to the supplier's
manuals (refer to (Refer to TASK )TASK 25-41-58-870-802-A01).
NOTE: Do not use KETONE or ACETONE for the cleaning of these parts after the
repair:
– the floor pan,
– the service cabinet,
– the seat cover dispenser,
– the toilet shrouds with the supports,
– the air grids,
– all the parts made of poly carbonate.
Cover these parts if you work with KETONE or ACETONE to prevent of
moist.
Use only ETHANOL (Material. No. 11-520) to clean the parts made of
poly-carbonate.
REPAIR
Page 6078
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
– the screws of lower and upper attachments and all selflocking nuts,
– all the seals,
– all the bulbs and the fluorescent tubes.
(2) For the rivet replacement refer to the standard riveting procedure.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
C. Procedure
SUBTASK 25-41-58-350-026-A01
(a) Make the bonding area of the washstand cover and of the washstand cover
reinforcement rough. Use the abrasive paper, 320-400 grade of grain.
(b) Clean the bonding area with the Material No. 11-010 Isopropyl Alcohol.
REPAIR
Page 6079
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(c) Bond the washstand cover reinforcement to the washstand cover with the
Material No. 08-017 Bonding Metal/Metal.
REPAIR
Page 6080
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6081
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6082
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-300-817-A01
A. General
NOTE: Material No. 08-017 Bonding Metal/Metal is operator supplied and not part
of the kit.
NOTE: For the repair procedure of the subcomponents refer to the supplier's
manuals (refer to (Refer to TASK )TASK 25-41-58-870-802-A01).
NOTE: Do not use KETONE or ACETONE for the cleaning of these parts after the
repair:
– the floor pan,
– the service cabinet,
– the seat cover dispenser,
– the toilet shrouds with the supports,
– the air grids,
– all the parts made of poly carbonate.
Cover these parts if you work with KETONE or ACETONE to prevent of
moist.
Use only ETHANOL (Material. No. 11-520) to clean the parts made of
poly-carbonate.
REPAIR
Page 6083
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
– the screws of lower and upper attachments and all selflocking nuts,
– all the seals,
– all the bulbs and the fluorescent tubes.
(2) For the rivet replacement refer to the standard riveting procedure.
REFERENCE DESIGNATION
REFERENCE DESIGNATION
abrasive paper
C. Procedure
SUBTASK 25-41-58-350-027-A01
(1) Scratches
REPAIR
Page 6084
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(a) Remove the scratches up to a depth of 0.3 mm (0.0118 in.) with the abrasive
paper. The grade of grain of the abrasive paper depends on the depth of the
scratches. Use step by step the next higher grade of grain.
SUBTASK 25-41-58-350-028-A01
(b) Use abrasive paper, 320-400 grade of grain, to remove the old bonding material
from the hinge (1) and from the waste chute flap (4).
(c) Use the Material No. 11-010 Isopropyl Alcohol to clean the bonding surfaces of
the hinge (1) and of the waste chute flap (4).
(d) Install the screws (3) on the hinge (1) and put the hinge (1) to the loaded
position.
(e) Put the Material No. 08-084 Polyester Film Tape (Transparent) 10 mm (0.394
in.) wide around the hinge (1) until the tape holds it in the loaded position.
(f) Apply the Material No. 08-051 Epoxy Resin to the surface of the hinge (1) to
be bonded.
(g) Put the hinge (1) in position and tighten the screws (3).
(h) Put the waste chute flap (4) in position from under the washbasin and hold it.
REPAIR
Page 6085
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(j) Cut the tape (2) Material No. 08-084 Polyester Film Tape (Transparent) and
allow the hinge (1) to come against the waste chute flap (4).
NOTE: The bond between the joints will take approximately 2 hours to
dry.
(k) Visually examine the waste chute flap (4) to make sure it is engaged correctly.
(l) Use the Material No. 11-010 Isopropyl Alcohol and Material No. 19-003
Lint-Free Cotton Cloth to remove unwanted bonding material.
For Myanmar Airways (MMA) use only
(m) Put the WARNING NOTICE in position to tell persons not to operate the waste
chute flap (4) for 2 hours.
(q) Push and release the waste chute flap (4) to make sure it operates correctly.
SUBTASK 25-41-58-350-029-A01
1 Push the waste flap (1) (refer to FIGURE 25-41-58-991-043-A) and set it
in the open position.
REPAIR
Page 6086
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
4 Chamfer the lower contoured edge of the replacement part (3) (refer to
FIGURE 25-41-58-991-044-A).
1 Make sure that the ambient temperature of the repair area is not less than
18 deg. C (64.40 deg. F).
2 Clean the mating surfaces of the repair with Material No. 11-006 Methyl
Alcohol and Material No. 19-003 Lint-Free Cotton Cloth.
3 Put the Material No. 08-074 Masking Tape in position on the lower surface
of the washbasin (2).
4 Apply the prepared adhesive, item of the Material No. VARICOR (Material
No. DCIN900) to the repair area of the washbasin.
5 Put the replacement part (3) in position with a light pressure and set it with
a PLIERS-NOSE, SOFT, LONG or a wooden block (4),
REPAIR
Page 6087
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
7 Remove the pliers or the wooden block (4) and the masking tape.
(d) Release the waste flap (1) (refer to FIGURE 25-41-58-991-043-A) and make
sure that it closes correctly.
For Myanmar Airways (MMA) use only
REPAIR
Page 6088
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6089
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6090
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6091
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
For Myanmar Airways (MMA) use only
REPAIR
Page 6092
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-350-801-A01
A. General
Each subtask of this task gives data for a different type of adhesive, sealant or
bonding material.
REFERENCE DESIGNATION
11-583 Solvent
HELMIPUR-SH100 (V D0293)
REPAIR
Page 6093
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
REFERENCE DESIGNATION
DAN98S2A/B
DAN98S3A/B
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
Non-Metallic Scraper
C. Procedure
REPAIR
Page 6094
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
SUBTASK 25-41-58-360-001-A01
(1) Replacement of the Parts which are bonded with Material No. 08-026
Adhesive/Sealant one Part, RTV Silicone Rubber
NOTE: The process and material specification PMS 01-02-37 gives more data
about the bonding with silicone base adhesives.
(a) Remove the damaged or delaminated part with a Non-Metallic Scraper or with
For Myanmar Airways (MMA) use only
NOTE: You can use a Hot-Air Blower with low heat to make the adhesive
soft for an easier removal.
(b) If necessary, remove larger quantities of adhesive with Material No. 19-011
Scotch Brite Pads or with Abrasive Paper, 120 grade of grain.
(c) Clean the repair area with Material No. 11-583 Solvent or Material No. 11-010
Isopropyl Alcohol and a Material No. 19-003 Lint-Free Cotton Cloth.
(e) Apply the Material No. 08-026 Adhesive/Sealant one Part, RTV Silicone
Rubber equally to the bonding area.
(f) Put the new part in position and bond it to the bonding surface.
NOTE: You can use Material No. 08-074 Masking Tape to hold the part
in its position.
(g) If necessary, apply pressure to the bonded part to remove air bubbles and
creases and use a Spatula or equivalent to make the adhesive joint smooth.
REPAIR
Page 6095
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(k) Remove any unwanted adhesive with Material No. 11-583 Solvent and Material
No. 19-003 Lint-Free Cotton Cloth.
SUBTASK 25-41-58-360-002-A01
(1) Replacement of the Parts which are bonded with 08-001 General Purpose Adhesive
Honeycomb Filler or Material No. 08-010A Epoxy Resin and Hardener Adhesive
or Material No. 08-017A Adhesive Structuralflexible
NOTE: The process and material specification PMS 01-02-27 gives more data
about the application of epoxy primers.
NOTE: The process and material specification PMS 02-08-06 gives more data
about the bonding with epoxy adhesives.
NOTE: The process and material specification PMS 02-08-09 gives more data
For Myanmar Airways (MMA) use only
(a) Remove the damaged or delaminated part with a Non-Metallic Scraper or with
a Milling Cutter from the bonding surface.
NOTE: You can use a Hot-Air Blower with low heat to make the adhesive
soft for an easier removal.
(b) If necessary, remove larger quantities of adhesive with Material No. 19-011
Scotch Brite Pads or with Abrasive Paper, 120 grade of grain.
(c) Clean the repair area with Material No. 11-583 Solvent or Material No. 11-010
Isopropyl Alcohol and a Material No. 19-003 Lint-Free Cotton Cloth.
(e) Apply the Material No. 08-001 General Purpose Adhesive Honeycomb Filler
or Material No. 08-010A Epoxy Resin and Hardener Adhesive or Material No.
08-017A Adhesive Structuralflexible equally to the bonding area.
(f) Put the new part in position and bond it to the bonding surface.
NOTE: You can use Material No. 08-074 Masking Tape to hold the part
in its position.
(g) If necessary, apply pressure to the bonded part to remove air bubbles and
creases and use a Spatula or equivalent to make the adhesive joint smooth.
REPAIR
Page 6096
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(k) Remove any unwanted adhesive with Material No. 11-583 Solvent and Material
No. 19-003 Lint-Free Cotton Cloth.
SUBTASK 25-41-58-360-003-A01
(1) Replacement of the Parts which are bonded with Material No. 08-553 Formica
Bonding Rigid Vinyl
(a) Remove the damaged or delaminated part with a Non-Metallic Scraper or with
a Milling Cutter from the bonding surface.
NOTE: You can use a Hot-Air Blower with low heat to make the adhesive
For Myanmar Airways (MMA) use only
(b) If necessary, remove larger quantities of adhesive with Material No. 19-011
Scotch Brite Pads or with Abrasive Paper, 120 grade of grain.
(c) Clean the repair area with Material No. 11-583 Solvent or Material No. 11-010
Isopropyl Alcohol and a Material No. 19-003 Lint-Free Cotton Cloth.
(e) Apply the Material No. 08-553 - Formica Bonding Rigid Vinyl with a Spray Gun,
1.5 mm (0.059 in) nozzle diameter and 6 - 7 bar (87.023 - 101.526 psi) air
pressure from a distance of between 300 mm (11.81 in) to 500 mm (19.69 in)
or with a Paint Roller equally to the bonding area.
(f) Put the new part in position and bond it to the bonding surface.
(g) If necessary, apply pressure to the bonded part to remove air bubbles and
creases and use a Spatula or equivalent to make the adhesive joint smooth.
(j) Remove any unwanted adhesive with Material No. 11-583 Solvent and Material
No. 19-003 Lint-Free Cotton Cloth.
SUBTASK 25-41-58-360-004-A01
(1) Replacement of the Parts which are bonded with Material No. 08-025 Two
Component Polyurethane Adhesive or Material No. HELMIPUR-SH100 (V D0293)
REPAIR
Page 6097
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(a) Remove the damaged or delaminated part with a Non-Metallic Scraper from
the bonding surface.
NOTE: You can use a Hot-Air Blower with low heat to make the adhesive
soft for an easier removal.
(b) If necessary, remove larger quantities of adhesive with Material No. 19-011
Scotch Brite Pads or with Abrasive Paper, 120 grade of grain.
(c) Clean the repair area with Material No. 11-583 Solvent or Material No. 11-010
Isopropyl Alcohol and a Material No. 19-003 Lint-Free Cotton Cloth.
(e) Apply the Material No. 08-025 Two Component Polyurethane Adhesive or
Material No. HELMIPUR-SH100 (V D0293) equally to the bonding area.
For Myanmar Airways (MMA) use only
NOTE: If necessary, you can use a short bristled Brush or a Paint Roller.
(f) Put the new part in position and bond it to the bonding surface.
NOTE: You can use Material No. 08-074 Masking Tape to hold the part
in its position.
(g) If necessary, apply pressure to the bonded part to remove air bubbles and
creases and use a Spatula or equivalent to make the adhesive joint smooth.
(k) Remove any unwanted adhesive with Material No. 11-583 Solvent or Material
No. 11-010 Isopropyl Alcohol and a Material No. 19-003 Lint-Free Cotton Cloth.
SUBTASK 25-41-58-360-005-A01
(1) Replacement of the Parts which are bonded with Material No. 08-006B Adhesive
General Purpose
(a) Remove the damaged or delaminated part with a Non-Metallic Scraper from
the bonding surface.
NOTE: You can use a Hot-Air Blower with low heat to make the adhesive
soft for an easier removal.
REPAIR
Page 6098
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(b) If necessary, remove larger quantities of adhesive with Material No. 19-011
Scotch Brite Pads or with Abrasive Paper, 120 grade of grain.
(c) Clean the repair area with Material No. 11-583 Solvent or Material No. 11-010
Isopropyl Alcohol and a Material No. 19-003 Lint-Free Cotton Cloth.
(e) Apply the Material No. 08-006B Adhesive General Purpose equally to the
bonding area.
(f) Put the new part in position and bond it to the bonding surface.
NOTE: You can use Material No. 08-074 Masking Tape to hold the part
For Myanmar Airways (MMA) use only
in its position.
(g) If necessary, apply pressure to the bonded part to remove air bubbles and
creases and use a Spatula or equivalent to make the adhesive joint smooth.
(k) Remove any unwanted adhesive with Material No. 11-583 Solvent or Material
No. 11-010 Isopropyl Alcohol and a Material No. 19-003 Lint-Free Cotton Cloth.
SUBTASK 25-41-58-360-006-A01
(1) Replacement of the Silicone Sealant made of Material No. 09-054 Silicone Sealant
(1 Part) for NTF or Material No. 09-059 Silicone Sealant
NOTE: The process and material specification PMS 02-08-07 gives more data
about the adhesive bonding of silicone with silicone sealant.
(a) Make sure that the replacement silicone sealant has the correct color before
you do this procedure.
REPAIR
Page 6099
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
NOTE: You can use a Hot-Air Blower with low heat to make the sealant
soft for an easier removal.
(c) If necessary, remove larger quantities of adhesive with Material No. 19-011
Scotch Brite Pads or with Abrasive Paper, 120 grade of grain.
(d) Clean the repair area with Material No. 11-583 Solvent or Material No. 11-010
Isopropyl Alcohol and a Material No. 19-003 Lint-Free Cotton Cloth.
(f) Apply the Material No. 09-054 Silicone Sealant (1 Part) for NTF or Material No.
09-059 Silicone Sealant with a Seal Gun equally to the area to be sealed.
For Myanmar Airways (MMA) use only
(g) When you repair the floor pan, apply the Material No. 09-054 Silicone Sealant
(1 Part) for NTF to the top edges of the floor pan which have contact with the
lavatory housing and side wall and between the floor pan and the floor panel.
Apply the Material No. 09-054 Silicone Sealant (1 Part) for NTF around the
edges of the non-textile floor covering (NTF) of the floor pan.
(h) If necessary, use a Spatula or equivalent to make the sealant joint smooth.
(j) Remove any unwanted sealant with Material No. 11-583 Solvent and a Material
No. 19-003 Lint-Free Cotton Cloth.
SUBTASK 25-41-58-360-007-A01
(1) Replacement of the Parts which are bonded with Adhesive Foam Tape as for
instance Material No. 08-005 Sealant Tape, obsolete-use 08-005A,B,C or Material
No. 08-696 - 3M SCOTCH VHB Tape 4930 or Material No. 3M SCOTCH MOUNT
4032 (V D26066)
(a) Remove the damaged part with a Non-Metallic Scraper from the bonding
surface.
NOTE: You can use a Hot-Air Blower with low heat to make the adhesive
soft for an easy removal.
(b) Remove the adhesive foam tape from the bonding surfaces.
REPAIR
Page 6100
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(c) Clean the repair area with Material No. 11-583 Solvent or Material No. 11-010
Isopropyl Alcohol and a Material No. 19-003 Lint-Free Cotton Cloth.
(d) Cut new pieces of the Material No. 08-005 Sealing Tape, obsolete-use
08-005A,B,C or Material No. 08-696 - 3M SCOTCH VHB Tape 4930 or Material
No. 3M SCOTCH MOUNT 4032 (V D26066) and remove the protection paper.
(g) If necessary, apply pressure to the bonded part to remove air bubbles and
creases.
SUBTASK 25-41-58-360-008-A01
For Myanmar Airways (MMA) use only
(1) Replacement of the Parts which are bonded with Adhesive Tape as for instance
Material No. 08-082 Acrylic Pressure Sensitive Adhesive Film
(a) Remove the damaged part with a Non-Metallic Scraper from the bonding
surface.
NOTE: You can use a Hot-Air Blower with low heat to make the adhesive
soft for an easier removal.
(c) Clean the repair area with Material No. 11-583 Solvent or Material No. 11-010
Isopropyl Alcohol and a Material No. 19-003 Lint-Free Cotton Cloth.
(d) Cut new pieces of the Material No. 08-082 Acrylic Pressure Sensitive Adhesive
Film and remove the protection paper.
(e) Bond the Material No. 08-082 Acrylic Pressure Sensitive Adhesive Film to
the bonding surfaces.
(g) If necessary, apply pressure to the bonded part to remove air bubbles and
creases.
SUBTASK 25-41-58-360-009-A01
(1) Replacement of the Parts which are attached with Hook/Loop Tape as for instance
Material No. DAN98S2A/B or Material No. DAN98S3A/B
REPAIR
Page 6101
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(c) Clean the repair area with Material No. 11-583 Solvent or Material No. 11-010
Isopropyl Alcohol and a Material No. 19-003 Lint-Free Cotton Cloth.
(d) Cut new pieces of the hook/loop tape Material No. DAN98S2A/B or Material
No. DAN98S3A/B and remove the protection paper.
(e) Bond the hook/loop tape Material No. DAN98S2A/B or Material No.
DAN98S3A/B to the bonding surfaces.
SUBTASK 25-41-58-360-010-A01
For Myanmar Airways (MMA) use only
(a) Remove the damaged part with a Non-Metallic Scraper from the bonding
surface.
NOTE: You can use a Hot-Air Blower with low heat to make the adhesive
soft for an easier removal.
(b) Clean the repair area with Material No. 11-583 Solvent or Material No. 11-010
Isopropyl Alcohol and a Material No. 19-003 Lint-Free Cotton Cloth.
REPAIR
Page 6102
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-350-802-A01
Self explanatory.
REFERENCE DESIGNATION
11-003 Methyl-Ethyl-Ketone
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
vacuum cleaner
C. Procedure
REPAIR
Page 6103
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
SUBTASK 25-41-58-350-030-A01
NOTE: See TABLE for the components and their replacement parts.
REPAIR
Page 6104
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
REPAIR
Page 6105
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
17D-060 Assembly
Angle
(d) Remove the dirt from the work area with a vacuum cleaner.
REPAIR
Page 6106
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(e) Clean the work area with Material No. 11-003 Methyl-Ethyl-Ketone.
(f) Apply Material No. 09-005A Interfay Sealant to the new rivets, see PMS
01-05-47 .
(g) Apply Material No. 09-005A Interfay Sealant to the mating surfaces of the
component part and the new replacement part.
REPAIR
Page 6107
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
TASK 25-41-58-350-803-A01
- Not applicable
REFERENCE DESIGNATION
REFERENCE DESIGNATION
nonmetallic scraper
C. Procedure
SUBTASK 25-41-58-350-031-A01
REPAIR
Page 6108
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
NOTE: The Process and Material Specification PMS 01-06-03 gives data about
installation of self-adhesive labels in non-Skydrol areas.
NOTE: See TABLE for the components and their replacement parts.
REPAIR
Page 6109
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
Single Door
Assembly
REPAIR
Page 6110
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
(a) Make a copy of the data of the damaged placard on the new placard.
3 Clean the repair area with Material No. 19-003 Lint-Free Cotton Cloth
made moist with Material No. 11-010 Isopropyl Alcohol.
4 Dry the repair area with Material No. 19-003 Lint-Free Cotton Cloth.
6 Align and attach the new placard to the position of the removed damaged
placard.
REPAIR
Page 6111
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
REPAIR
Page 6112
25-41-58 Jun 30/14
COMPONENT MAINTENANCE MANUAL
D254-, R2254-SERIES
ASSEMBLY
TASK 25-41-58-400-801-A01
A. General
C. Procedure
For Myanmar Airways (MMA) use only
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-001-A01
(a) Install and assemble the center electric strike 31-270 as follows:
For Myanmar Airways (MMA) use only
1 Attach the spring sheets 31-190 and the sheets 31-210, 31-220.
3 Attach the rear part of the center electric strike 31-270 with the screws
31-240, 31-250 to the front part of the center electric strike 31-270.
1 Attach the spring sheets 31-190 and the sheets 31-210, 31-220.
3 Attach the rear part of the electric strikes 31-200 with the screws 31-240,
31-250 to the front part of the electric strikes 31-200.
(c) Attach the clamp 31-160 with the screw 31-170 and the washer 31-180.
(d) Attach the clamp 31-150 with the screw 31-170 and the washer 31-180.
1 Attach the cable ties 31-040, the receptacle connector 31-050 and the
backshell 31-060 with the coupling screws 31-070.
3 Attach the plug connector 31-020 and the connector backshell 31-030.
SUBTASK 25-41-58-440-001-B01
(0) Assembly of the Electrical System of the Cockpit Door Locking (31-1)
1 Attach the spring sheets 31-190 and the sheets 31-210, 31-220.
3 Attach the rear part of the electric strike 31-200 with the screws 31-240,
31-250 to the front part of the electric strike 31-200.
(b) Install and assemble the center electric strike 31-270 as follows:
For Myanmar Airways (MMA) use only
1 Attach the spring sheets 31-190 and the sheets 31-210, 31-220.
3 Attach the rear part of the center electric strike 31-270 and the sub rack
assemblies 31-205 with the screws 31-240, 31-250 to the front part of
the center electric strike 31-270.
4 Attach the rear part of the center electric strike 31-270 with the screws
31-240, 31-250 to the front part of the center electric strike 31-270.
1 Attach the spring sheets 31-190 and the sheets 31-210, 31-220.
3 Attach the rear part of the electric strike 31-200 and the sub rack
assemblies 31-205 with the screws 31-240, 31-250 to the front part of
the electric strike 31-200.
4 Attach the rear part of the electric strike 31-200 with the screws 31-240,
31-250 to the front part of the electric strike 31-200.
(d) Attach the clamp 31-160 with the screw 31-170 and the washer 31-180.
(e) Attach the clamp 31-150 with the screw 31-170 and the washer 31-180.
1 Attach the cable ties 31-040, the receptacle connector 31-050 and the
backshell 31-060 with the coupling screws 31-070.
3 Attach the plug connector 31-020 and the connector backshell 31-030.
SUBTASK 25-41-58-440-001-C01
D2549020307400
For Myanmar Airways (MMA) use only
(0) Assembly of the Electrical System of the Cockpit Door Locking (31-1)
3 Attach the CDLS slider 31-300 with the screw 31-380, the bushing 31-320
and the dead bolt 31-310.
5 Attach the CDLS slider 31-290 and the spring 31-390 with the screw
31-400, the washers 31-330, 31-360 and the nut 31-350.
1 Attach the spring sheets 31-190 and the sheets 31-210, 31-220.
3 Attach the rear part of the electric strike 31-200 with the screws 31-240,
31-250 to the front part of the electric strike 31-200.
(c) Install and assemble the center electric strike 31-270 as follows:
1 Attach the spring sheets 31-190 and the sheets 31-210, 31-220.
3 Attach the rear part of the center electric strike 31-270 with the screws
31-240, 31-250 to the front part of the center electric strike 31-270.
(d) Attach the clamp 31-160 with the screw 31-170 and the washer 31-180.
(e) Attach the clamp 31-150 with the screw 31-170 and the washer 31-180.
1 Attach the cable ties 31-040, the receptacle connector 31-050 and the
backshell 31-060 with the coupling screws 31-070.
3 Attach the plug connector 31-020 and the connector backshell 31-030.
SUBTASK 25-41-58-440-001-D01
3 Attach the CDLS slider 31-300 with the screw 31-380, the bushing 31-320
and the dead bolt 31-310.
5 Attach the CDLS slider 31-290 and the spring 31-390 with the screw
31-400, the washers 31-330, 31-360 and the nut 31-350.
1 Attach the spring sheets 31-190 and the sheets 31-210, 31-220.
3 Attach the rear part of the electric strike 31-200 with the screws 31-240,
31-250 to the front part of the electric strike 31-200.
(c) Install and assemble the center electric strike 31-270 as follows:
For Myanmar Airways (MMA) use only
1 Attach the spring sheets 31-190 and the sheets 31-210, 31-220.
3 Attach the rear part of the center electric strike 31-270 with the screws
31-240, 31-250 to the front part of the center electric strike 31-270.
(d) Attach the clamp 31-160 with the screw 31-170 and the washer 31-180.
(e) Attach the clamp 31-150 with the screw 31-170 and the washer 31-180.
1 Attach the cable ties 31-040, the receptacle connector 31-050 and the
backshell 31-060 with the coupling screws 31-070.
3 Attach the plug connector 31-020 and the connector backshell 31-030.
TASK 25-41-58-400-802-A01
A. General
For Myanmar Airways (MMA) use only
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-003-A01
(1) Assembly of the Cable Harness Assembly (27-1)
(a) Attach the cable ties 27-280, the plug connector 27-290 and the connector
backshell 27-300.
(b) Attach the bracket 27-230, the receptacle connector 27-210 and the connector
backshell 27-220 with the nuts 27-240.
(c) Attach the cable terminals 27-140 and the insulations 27-150.
(d) Attach the cable terminals 27-120 and the housings 27-130.
(e) Attach the receptacle connector 27-080, the cable bracket 27-090, the
protective cap 27-100, the identification sleeves 27-110, the modules 27-160,
27-170, the rail 27-180, the end clamps 27-190 and the plugs 27-200.
(f) Attach the connector 27-530, the spring latches 27-540, the backshell 27-550
and the socket contacts 27-560.
(g) Attach the identification ties 27-030, the socket contacts 27-050, the receptacle
connector 27-080, the cable bracket 27-090 and the protective cap 27-100.
For Myanmar Airways (MMA) use only
(h) Attach the splices 27-010, the contact pins 27-020, the identification ties
27-030, the socket contacts 27-050, the connector backshell 27-060 and the
plug connector 27-070.
(j) Attach the bracket 27-420, the identification sleeves 27-110, 27-460, the plugs
27-200, the receptacle connector 27-400, the connector backshell 27-410,
the labels 27-450 and the cable ties 27-470 with the screws 27-430 and the
nuts 27-240.
TASK 25-41-58-400-802-B01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-004-A01
(a) Attach the plug 27A-390, the cable ties 27A-400 and the plug connector
27A-410.
(b) Attach the bracket 27A-290 and the connector backshell 27A-280 with the
nuts 27A-300.
(d) Attach the cable terminals 27A-160 and the insulations 27A-170.
(e) Attach the cable terminals 27A-140 and the housings 27A-150.
(g) Attach the identification sleeves 27A-130, the modules 27A-180, 27A-190, the
end clamps 27A-210 and the plugs 27A-220.
(h) Attach the identification ties 27A-030, the socket contacts 27A-050, the
connector 27A-080, the spring latches 27A-090, the receptacle connector
27A-100, the cable bracket 27A-110 and the protective cap 27A-120.
(j) Attach the splices 27A-010, the contacts 27A-020, the identification ties
For Myanmar Airways (MMA) use only
(k) Attach the bracket 27A-540, the identification sleeves 27A-130, 27A-580, the
plugs 27A-220, the receptacle connector 27A-520, the connector backshell
27A-530, the labels 27A-570 with the screws 27A-550 and the nuts 27A-300.
SUBTASK 25-41-58-440-004-B01
(a) Attach the plug 27A-390, the cable ties 27A-400, the plug connector 27A-410
and the connector backshell 27A-420.
(b) Attach the bracket 27A-290, the receptacle connector 27A-270 and the
connector backshell 27A-280 with the nuts 27A-300.
(d) Attach the cable terminals 27A-160 and the insulations 27A-170.
For Myanmar Airways (MMA) use only
(e) Attach the cable terminals 27A-140 and the housings 27A-150.
(f) Attach the identification sleeves 27A-130, the modules 27A-180, 27A-190, the
rail 27A-200, the end clamps 27A-210 and the plugs 27A-220.
(g) Attach the identification ties 27A-030, the socket contacts 27A-050, the
connector 27A-080, the spring latches 27A-090, the receptacle connector
27A-100, the cable bracket 27A-110 and the protective cap 27A-120.
(h) Attach the splices 27A-010, the contacts 27A-020, the identification ties
27A-030, the socket contacts 27A-050, 27A-330, the connector backshell
27A-060, the plug connector 27A-070, the relay 27A-310, the base 27A-320
and the angle 27A-340.
(j) Attach the bracket 27A-540, the identification sleeves 27A-130, 27A-580, the
plugs 27A-220, the receptacle connector 27A-520, the connector backshell
27A-530, the labels 27A-570 with the screws 27A-550 and the nuts 27A-300.
SUBTASK 25-41-58-440-004-C01
D2549010301000 D2549010413800
(0) Assembly of the Cable Harness Assembly (27A-1)
(a) Attach the plug 27A-390, the cable ties 27A-400 and the plug connector
27A-410.
(b) Attach the bracket 27A-290, the receptacle connector 27A-270 and the
connector backshell 27A-280 with the nuts 27A-300.
(d) Attach the cable terminals 27A-160 and the insulations 27A-170.
(e) Attach the cable terminals 27A-140 and the housings 27A-150.
(f) Attach the identification sleeves 27A-130, the modules 27A-180, 27A-190, the
rail 27A-200, the end clamps 27A-210 and the plugs 27A-220.
(g) Attach the identification ties 27A-030, the socket contacts 27A-050, the
connector 27A-080, the spring latches 27A-090, the receptacle connector
27A-100, the cable bracket 27A-110 and the protective cap 27A-120.
For Myanmar Airways (MMA) use only
(h) Attach the splices 27A-010, the contacts 27A-020, the identification ties
27A-030, the socket contacts 27A-050, 27A-330, the connector backshell
27A-060, the plug connector 27A-070, the relay 27A-310, the base 27A-320
and the angle 27A-340.
(j) Attach the bracket 27A-540, the identification sleeves 27A-130, 27A-580, the
plugs 27A-220, the receptacle connector 27A-520, the connector backshell
27A-530, the labels 27A-570 with the screws 27A-550, 27A-770 and the nuts
27A-300.
TASK 25-41-58-400-803-A01
A. General
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-006-A01
D2549020307200 D2549030708000
(1) Assembly of the Electrical System (26-1)
(a) Attach the ami cabin attendant seat-cable 26-270, the connector backshell
26-310 and the plug connectors 26-300, 26-320.
(b) Attach the clamp 26-250 with the screw 26-220 and the washer 26-230.
(c) Attach the cable ties 26-110 with the screws 26-080 and the washers 26-090.
(d) Attach the nut 26-197, 26-240 and the washer 26-230.
(f) Attach the bracket 26-070 with the screws 26-080 and the washers 26-090 to
the lavatory structure.
(j) Attach the bracket 26-070 with the screws 26-080 and the washers 26-090 to
the lavatory structure.
(l) Attach the smoke detector sealing 26-030 and the smoke detector 26-020 with
the screws 26-040 and the nuts 26-050.
(n) Connect the cables, the bonding straps 26-170, 26-180, 26-190, 26-195,
26-200, 26-210 and the cable harness assembly 26-010 to the electrical
components.
SUBTASK 25-41-58-440-006-B01
(a) Attach the ami cabin attendant seat-cable 26-270, the connector backshell
26-310 and the plug connectors 26-300, 26-320.
(b) Attach the clamp 26-250 with the screw 26-220 and the washer 26-230.
(c) Attach the cable ties 26-110 with the screws 26-080 and the washers 26-090.
(d) Attach the nuts 26-197, 26-240 and the washers 26-196, 26-230.
For Myanmar Airways (MMA) use only
(f) Attach the bracket 26-070 with the screws 26-080 and the washers 26-090 to
the lavatory structure.
(j) Attach the mini inverter 26-370 with the spacers 26-390 and the screws 26-380.
(k) Attach the bracket 26-070 with the screws 26-080 and the washers 26-090 to
the lavatory structure.
(m) Attach the smoke detector sealing 26-030 and the smoke detector 26-020 with
the screws 26-040 and the nuts 26-050.
(p) Connect the cables, the bonding straps 26-170, 26-180, 26-190, 26-195,
26-200, 26-210 and the cable harness assembly 26-010 to the electrical
components.
SUBTASK 25-41-58-440-006-C01
D2549030709200
(0) Assembly of the Electrical System (26-1)
For Myanmar Airways (MMA) use only
(a) Attach the ami cabin attendant seat-cable 26-270, the connector backshell
26-310 and the plug connectors 26-300, 26-320.
(b) Attach the clamp 26-250 with the screw 26-220 and the washer 26-230.
(c) Attach the cable ties 26-110 with the screws 26-080 and the washers 26-090.
(f) Attach the bracket 26-070 with the screws 26-080 and the washers 26-090 to
the lavatory structure.
(j) Attach the mini inverter 26-370 with the spacers 26-390 and the screws 26-380.
(k) Attach the bracket 26-070 with the screws 26-080 and the washers 26-090 to
the lavatory structure.
(m) Attach the smoke detector sealing 26-030 and the smoke detector 26-020 with
the screws 26-040 and the nuts 26-050.
(p) Connect the cables, the bonding straps 26-170, 26-180, 26-190, 26-200,
For Myanmar Airways (MMA) use only
26-210 and the cable harness assembly 26-010 to the electrical components.
TASK 25-41-58-400-803-B01
A. General
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-007-A01
(1) Assembly of the Electrical System (26A-1)
(a) Attach the ami cabin attendant seat-cable 26A-320, the connector backshell
26A-360 and the plug connectors 26A-350, 26A-370.
(b) Attach the clamp 26A-280 with the screw 26A-230 and the washer 26A-240.
(e) Attach the microswitch 26A-160 and the shrinkable heat tubings 26A-180,
26A-190 with the screws 26A-170.
(f) Attach the bracket 26A-070 with the screws 26A-080 and the washers 26A-090
to the lavatory structure.
(j) Attach the mini inverter 26A-290 with the spacers 26A-300 and the screws
26A-310.
(l) Attach the smoke detector sealing 26A-030 and the smoke detector 26A-020
with the screws 26A-040 and the nuts 26A-050.
(m) Connect the cables, the bonding straps 26A-200, 26A-210, 26A-220,
26A-250, 26A-260 and the cable harness assembly 26A-010 to the electrical
components.
TASK 25-41-58-400-803-C01
A. General
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-008-A01
(1) Assembly of the Electrical System (26B-1)
(a) Install and assemble the 2065 VU switch panel 26B-390 as follows:
1 Attach the switch button-switch 26B-480 to the printed circuit board PCB
26B-450.
a Attach the switch housing 26B-410 with the screws 26B-460 and the
spring washers 26B-470 to the printed circuit board PCB 26B-450.
4 Attach the plugs 26B-500 to the printed circuit board PCB 26B-450.
(b) Attach the ami cabin attendant seat-cable 26B-260, the connector backshell
26B-300 and the plug connectors 26B-290, 26B-310.
(c) Attach the clamp 26B-240 with the screw 26B-210 and the washer 26B-220.
(d) Attach the cable ties 26B-100 with the screws 26B-250 and the washers
For Myanmar Airways (MMA) use only
26B-080.
(g) Attach the bracket 26B-070 with the screws 26B-250 and the washers 26B-080
to the lavatory structure.
(k) Attach the mini inverter 26B-360 with the spacers 26B-380 and the screws
26B-370.
(l) Attach the bracket 26B-070 with the screws 26B-250 and the washers 26B-080
to the lavatory structure.
(n) Attach the smoke detector sealing 26B-030 and the smoke detector 26B-020
with the screws 26B-040 and the nuts 26B-050.
(p) Connect the cables, the bonding straps 26B-160, 26B-170, 26B-180,
26B-190, 26B-200 and the cable harness assembly 26B-010 to the electrical
components.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-803-D01
A. General
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-009-A01
D2549010414600
(1) Assembly of the Electrical System (26C-1)
(b) Attach the microswitch 26C-150 and the shrinkable heat tubings 26C-170,
26C-180 with the screws 26C-160.
(d) Attach the bracket 26C-070 with the screws 26C-080 and the washers 26C-090
to the lavatory structure.
(g) Attach the mini inverter 26C-280 with the spacers 26C-290 and the screws
26C-300.
(j) Attach the smoke detector sealing 26C-030 and the smoke detector 26C-020
For Myanmar Airways (MMA) use only
(k) Connect the cables and the cable harness assembly 26C-010 to the electrical
components.
SUBTASK 25-41-58-440-009-B01
the plugs 26C-390, the labels 26C-490 and the identification sleeves
26C-500, 26C-510.
(b) Attach the clamp 26C-270 with the screw 26C-220 and the washer 26C-230.
(c) Attach the microswitch 26C-150 and the shrinkable heat tubings 26C-170,
26C-180 with the screws 26C-160.
(d) Attach the bracket 26C-070 with the screws 26C-080 and the washers 26C-090
to the lavatory structure.
(g) Attach the mini inverter 26C-280 with the spacers 26C-290 and the screws
26C-300.
(j) Attach the smoke detector sealing 26C-030 and the smoke detector 26C-020
with the screws 26C-040 and the nuts 26C-050.
(k) Attach the bonding strap 26C-19026C-190 with the nut 26C-260 and the
washer 26C-230, 26C-232, 26C-234.
(l) Connect the cables, the bonding straps 26C-200, 26C-210, 26C-240, 26C-250
and the cable harness assembly 26C-010 to the electrical components.
SUBTASK 25-41-58-440-009-C01
(b) Attach the clamp 26C-270 with the screw 26C-220 and the washer 26C-230.
(c) Attach the microswitch 26C-150 and the shrinkable heat tubings 26C-170,
26C-180 with the screws 26C-160.
For Myanmar Airways (MMA) use only
(e) Attach the bracket 26C-070 with the screws 26C-080 and the washers 26C-090
to the lavatory structure.
(h) Attach the mini inverter 26C-280 with the spacers 26C-290 and the screws
26C-300.
(k) Attach the smoke detector sealing 26C-030 and the smoke detector 26C-020
with the screws 26C-040 and the nuts 26C-050.
(l) Attach the bonding strap 26C-190 with the nut 26C-260 and the washer
26C-230.
(m) Connect the cables, the bonding straps 26C-200, 26C-210, 26C-240, 26C-250
and the cable harness assembly 26C-010 to the electrical components.
SUBTASK 25-41-58-440-009-D01
(b) Attach the clamp 26C-270 with the screw 26C-220 and the washer 26C-230.
(c) Attach the microswitch 26C-150 and the shrinkable heat tubings 26C-170,
26C-180 with the screws 26C-160.
(f) Attach the bracket 26C-070 with the screws 26C-080 and the washers 26C-090
to the lavatory structure.
(j) Attach the mini inverter 26C-280 with the spacers 26C-290 and the screws
26C-300.
(l) Attach the smoke detector sealing 26C-030 and the smoke detector 26C-020
For Myanmar Airways (MMA) use only
(m) Attach the bonding strap 26C-190 with the nut 26C-260 and the washer
26C-230.
(n) Connect the cables, the bonding straps 26C-200, 26C-210, 26C-240, 26C-250
and the cable harness assembly 26C-010 to the electrical components.
SUBTASK 25-41-58-440-009-E01
(b) Attach the clamp 26C-270 with the screw 26C-220 and the washer 26C-230.
(c) Attach the microswitch 26C-150 and the shrinkable heat tubings 26C-170,
26C-180 with the screws 26C-160.
(f) Attach the bracket 26C-070 with the screws 26C-080 and the washers 26C-090
to the lavatory structure.
(j) Attach the mini inverter 26C-280 with the spacers 26C-290 and the screws
26C-300.
(l) Attach the smoke detector sealing 26C-030 and the smoke detector 26C-020
with the screws 26C-040 and the nuts 26C-050.
(n) Connect the cables, the bonding straps 26C-200, 26C-210, 26C-240, 26C-250
and the cable harness assembly 26C-010 to the electrical components.
TASK 25-41-58-400-803-E01
A. General
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-010-A01
(a) Install and assemble the 2065 VU switch panel 26D-370 as follows:
1 Attach the switch button-switch 26D-460 to the printed circuit board PCB
26D-430.
a Attach the switch housing 26D-390 with the screws 26D-440 and the
spring washers 26D-450 to the printed circuit board PCB 26D-430.
4 Attach the plugs 26D-480 to the printed circuit board PCB 26D-430.
(b) Attach the ami cabin attendant seat-cable 26D-310, the connector backshell
26D-350 and the plug connectors 26D-340, 26D-360.
(c) Attach the clamp 26D-270 with the screw 26D-220 and the washer 26D-230.
For Myanmar Airways (MMA) use only
(d) Attach the microswitch 26D-150 and the shrinkable heat tubings 26D-170,
26D-180 with the screws 26D-160.
(f) Attach the bracket 26D-070 with the screws 26D-080 and the washers 26D-090
to the lavatory structure.
(j) Attach the mini inverter 26D-280 with the spacers 26D-290 and the screws
26D-300.
(l) Attach the smoke detector sealing 26D-030 and the smoke detector 26D-020
with the screws 26D-040 and the nuts 26D-050.
(m) Connect the cables, the bonding straps 26D-190, 26D-200, 26D-210,
26D-240, 26D-250 and the cable harness assembly 26D-010 to the electrical
components.
SUBTASK 25-41-58-440-010-B01
D2549030706800 D2549030809600
(0) Assembly of the Electrical System (26D-1)
(a) Install and assemble the 2065 VU switch panel 26D-370 as follows:
For Myanmar Airways (MMA) use only
1 Attach the switch button-switch 26D-460 to the printed circuit board PCB
26D-430.
a Attach the switch housing 26D-390 with the screws 26D-440 and the
spring washers 26D-450 to the printed circuit board PCB 26D-430.
4 Attach the plugs 26D-480 to the printed circuit board PCB 26D-430.
(b) Attach the ami cabin attendant seat-cable 26D-310, the connector backshell
26D-350 and the plug connectors 26D-340, 26D-360.
(c) Attach the clamp 26D-270 with the screw 26D-220 and the washer 26D-230.
(d) Attach the microswitch 26D-150 and the shrinkable heat tubings 26D-170,
26D-180 with the screws 26D-160.
(g) Attach the bracket 26D-070 with the screws 26D-080 and the washers 26D-090
to the lavatory structure.
(k) Attach the mini inverter 26D-280 with the spacers 26D-290 and the screws
26D-300.
(m) Attach the smoke detector sealing 26D-030 and the smoke detector 26D-020
with the screws 26D-040 and the nuts 26D-050.
(n) Connect the cables, the bonding straps 26D-190, 26D-200, 26D-210,
26D-240, 26D-250 and the cable harness assembly 26D-010 to the electrical
components.
TASK 25-41-58-400-803-F01
A. General
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-011-A01
(1) Assembly of the Electrical System (26E-1)
(a) Install and assemble the 2065 VU switch panel 26E-460 as follows:
1 Attach the switch button-switch 26E-550 to the printed circuit board PCB
26E-520.
a Attach the switch housing 26E-480 with the screws 26E-530 and the
spring washers 26E-540 to the printed circuit board PCB 26E-520.
4 Attach the plugs 26E-570 to the printed circuit board PCB 26E-520.
(b) Attach the bonding strap 26E-240 with the screw 26E-330 and the washers
26E-300.
(c) Attach the ami cabin attendant seat-cable 26E-380, the connector backshell
26E-420 and the plug connectors 26E-410, 26E-430.
(d) Attach the clamp 26E-340 with the screw 26E-290 and the washer 26E-310.
(f) Attach the bonding straps 26E-210, 26E-230, 26E-260, 26E-280 with the screw
For Myanmar Airways (MMA) use only
(g) Attach the microswitch 26E-160 and the shrinkable heat tubings 26E-180,
26E-190 with the screws 26E-170.
(k) Attach the mini inverter 26E-350 with the spacers 26E-360 and the screws
26E-370.
(m) Attach the smoke detector sealing 26E-030 and the smoke detector 26E-020
with the screws 26E-040 and the nuts 26E-050.
(n) Connect the cables, the bonding straps 26E-220, 26E-250, 26E-270 and the
cable harness assembly 26E-010 to the electrical components.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-803-G01
D2549030709000
10. Assembly of the Electrical System
A. General
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-012-A01
(1) Assembly of the Electrical System (26F-1)
(a) Install and assemble the 2065 VU switch panel 26F-460 as follows:
1 Attach the switch button-switch 26F-550 to the printed circuit board PCB
26F-520.
a Attach the switch housing 26F-480 with the screws 26F-530 and the
spring washers 26F-540 to the printed circuit board PCB 26F-520.
4 Attach the plugs 26F-570 to the printed circuit board PCB 26F-520.
(b) Attach the bonding strap 26F-210 with the screw 26F-300 and the washers
26F-270.
(c) Attach the ami cabin attendant seat-cable 26F-330, the connector backshell
26F-370 and the plug connectors 26F-360, 26F-380.
(d) Attach the clamp 26F-310 with the screw 26F-260 and the washer 26F-280.
(e) Attach the cable ties 26F-110 with the screws 26F-080, 26F-320 and the
washers 26F-090.
For Myanmar Airways (MMA) use only
(f) Attach the bonding straps 26F-180, 26F-200, 26F-230, 26F-250 with the screw
26F-300, the washer 26F-280 and the nut 26F-290.
(h) Attach the bracket 26F-070 with the screws 26F-080 and the washers 26F-090
to the lavatory structure.
(l) Attach the mini inverter 26F-430 with the spacers 26F-450 and the screws
26F-440.
(m) Attach the bracket 26F-070 with the screws 26F-080 and the washers 26F-090
to the lavatory structure.
(p) Attach the smoke detector sealing 26F-030 and the smoke detector 26F-020
with the screws 26F-040 and the nuts 26F-050.
(q) Connect the cables, the bonding straps 26F-190, 26F-220, 26F-240 and the
cable harness assembly 26F-010 to the electrical components.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-803-H01
A. General
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-013-A01
(1) Assembly of the Electrical System (26G-1)
26G-510, 26G-520.
(b) Attach the clamp 26G-280 with the screw 26G-230 and the washer 26G-240.
(e) Attach the microswitch 26G-160 and the shrinkable heat tubings 26G-180,
26G-190 with the screws 26G-170.
(f) Attach the bracket 26G-070 with the screws 26G-080 and the washers
26G-090 to the lavatory structure.
(j) Attach the mini inverter 26G-290 with the spacers 26G-300 and the screws
26G-310.
(l) Attach the smoke detector sealing 26G-030 and the smoke detector 26G-020
with the screws 26G-040 and the nuts 26G-050.
(m) Connect the cables, the bonding straps 26G-200, 26G-210, 26G-220,
26G-250, 26G-260 and the cable harness assembly 26G-010 to the electrical
components.
TASK 25-41-58-400-803-J01
A. General
C. Procedure
For Myanmar Airways (MMA) use only
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-014-A01
D2549026001200
(1) Assembly of the Electrical System (26H-1)
26H-510, 26H-520.
(b) Attach the clamp 26H-270 with the screw 26H-220 and the washer 26H-230.
(c) Attach the microswitch 26H-150 and the shrinkable heat tubings 26H-170,
26H-180 with the screws 26H-160.
(e) Attach the bracket 26H-070 with the screws 26H-080 and the washers 26H-090
to the lavatory structure.
(h) Attach the mini inverter 26H-280 with the spacers 26H-290 and the screws
26H-300.
(k) Attach the smoke detector sealing 26H-030 and the smoke detector 26H-020
with the screws 26H-040 and the nuts 26H-050.
(l) Attach the bonding strap 26H-255 with the screws 26H-265 and the washers
26H-091.
(m) Connect the cables, the bonding straps 26H-190, 26H-200, 26H-210,
26H-240, 26H-250 and the cable harness assembly 26H-010 to the electrical
components.
SUBTASK 25-41-58-440-014-B01
(b) Attach the clamp 26H-270 with the screw 26H-220 and the washer 26H-230.
(c) Attach the microswitch 26H-150 and the shrinkable heat tubings 26H-170,
26H-180 with the screws 26H-160.
For Myanmar Airways (MMA) use only
(e) Attach the bracket 26H-070 with the screws 26H-080 and the washers 26H-090
to the lavatory structure.
(h) Attach the mini inverter 26H-280 with the spacers 26H-290 and the screws
26H-300.
(k) Attach the smoke detector sealing 26H-030 and the smoke detector 26H-020
with the screws 26H-040 and the nuts 26H-050.
(l) Connect the cables, the bonding straps 26H-190, 26H-200, 26H-210,
26H-240, 26H-250 and the cable harness assembly 26H-010 to the electrical
components.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-803-K01
D2549010300600 R225411623-000
13. Assembly of the Electrical System
A. General
- Not applicable
B. Procedure
SUBTASK 25-41-58-400-080-A01
D2549010300600 R225411623-000
(1) Assembly of the Electrical System
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-804-A01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-016-A01
(1) Assembly of the Waste Water System (23-1)
(a) Attach the bracket 23-050 with the screws 23-060, the washers 23-070 and the
nuts 23-080 to the lavatory structure.
(b) Attach the drain valve 23-040 with the screws 23-090, the washers 23-100 and
the nuts 23-110 to the bracket 23-050.
(c) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the drain valve 23-040.
(d) Attach the hose 23-120 with the clamp 23-030 to the lavatory structure.
(e) Attach the hose 23-120 with the clamp 23-030 to the drain valve 23-040.
(f) Attach the hose 23-120 with the clamps 23-130, 23-140, the spacer 23-150,
the screw 23-160 and the washer 23-170 to the lavatory structure.
(g) Attach the hose 23-120 with the clamps 23-130, 23-135, the screw 23-180, the
washer 23-170, 23-195 and the nut 23-190 to the lavatory structure.
assembly).
(j) Attach the hose 23-020 with the clamps 23-030 to the drain assembly 23-010,
to the lavatory structure and to the drain valve 23-040.
TASK 25-41-58-400-805-A01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-018-A01
(a) Attach shutoff valve bracket 22-190, the shutoff valve 22-210 with the screws
22-320 and the washers 22-330.
(b) Attach the shutoff valve rod 22-110 to the shutoff valve 22-210.
(c) Attach the shutoff valve bracket 22-190, the shutoff valve rod 22-110, the
grommet 22-120, the retaining ring 22-160 and the bracket 22-170 with the
screws 22-140, the washers 22-180 and the nuts 22-200 to the lavatory
structure.
(d) Attach the bracket 22-130 with the grommet 22-120, the screws 22-140, the
washers 22-050 and the nuts 22-150 to the shutoff valve rod 22-110 and to
the lavatory structure.
(e) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the shutoff valve 22-210.
(f) Attach the brackets 22-020 with the screws 22-040 and the washers 22-050 to
the lavatory structure.
(g) Attach the water heater 22-060 with the clamps 22-030 to the brackets 22-020.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the water heater 22-060.
(k) Attach the tube 22-250 with the clamp 22-270, the spacer 22-290, the screw
22-280 and the washer 22-050 to the shutoff valve 22-210.
(p) Attach the reducer elbow 22-070 to the water heater 22-060.
(q) Attach the tee 22-230 to the hose 22-240 and to the water heater 22-060.
(r) Attach the water faucet assembly 22-010 to the lavatory structure.
(s) Attach the tube of the water faucet assembly 22-010 to the tee 22-230.
(t) Attach the tube of water faucet assembly 22-010 with the clamp 22-080, the
spacer 22-100, the screw 22-090 and the washer 22-050 to the lavatory
structure.
(u) Attach the tube of water faucet assembly 22-010 to the reducer elbow 22-070.
(v) Attach the tubes of water faucet assembly 22-010 with the clamps 22-080,
the spacer 22-100, the screw 22-090 and the washer 22-050 to the lavatory
structure.
(w) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the water faucet assembly 22-010.
(x) Connect the water faucet assembly 22-010 to the water supply.
SUBTASK 25-41-58-440-018-B01
(a) Attach shutoff valve bracket 22-190, the shutoff valve 22-210 with the screws
22-320 and the washers 22-330.
(b) Attach the shutoff valve rod 22-110 to the shutoff valve 22-210.
(c) Attach the shutoff valve bracket 22-190, the shutoff valve rod 22-110, the
grommet 22-120, the retaining ring 22-160 and the bracket 22-170 with the
screws 22-140, the washers 22-180 and the nuts 22-200 to the lavatory
structure.
(d) Attach the bracket 22-130 with the grommet 22-120, the screws 22-140, the
washers 22-050 and the nuts 22-150 to the shutoff valve rod 22-110 and to
the lavatory structure.
(e) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the shutoff valve 22-210.
For Myanmar Airways (MMA) use only
(f) Attach the brackets 22-020 with the screws 22-040 and the washers 22-050 to
the lavatory structure.
(g) Attach the water heater 22-060 with the clamps 22-030 to the brackets 22-020.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the water heater 22-060.
(n) Attach the reducer elbow 22-070 to the water heater 22-060.
(p) Attach the tee 22-230 to the hose 22-240 and to the water heater 22-060.
(q) Attach the water faucet assembly 22-010 to the lavatory structure.
(r) Attach the tube of the water faucet assembly 22-010 to the tee 22-230.
(s) Attach the tube of water faucet assembly 22-010 with the clamp 22-080, the
spacer 22-100, the screw 22-090 and the washer 22-050 to the lavatory
structure.
(t) Attach the tube of water faucet assembly 22-010 to the reducer elbow 22-070.
(u) Attach the tubes of water faucet assembly 22-010 with the clamps 22-080,
the spacer 22-100, the screw 22-090 and the washer 22-050 to the lavatory
structure.
(v) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the water faucet assembly 22-010.
(w) Connect the water faucet assembly 22-010 to the water supply.
assembly).
TASK 25-41-58-400-805-B01
A. General
This task gives you the installation and assembly procedures of the component.
For Myanmar Airways (MMA) use only
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-019-A01
(1) Assembly of the Potable Water System (22A-1)
(a) Attach the shutoff valve 22A-240 and the shutoff valve bracket 22A-220 with
the screws 22A-300 and the washers 22A-310.
(b) Attach the shutoff valve rod 22A-140 to the shutoff valve 22A-240.
(c) Attach the shutoff valve rod 22A-140, the shutoff valve bracket 22A-220, the
grommet 22A-150, the retaining ring 22A-190 and the bracket 22A-200 with the
screws 22A-170, the washers 22A-210 and the nuts 22A-230 to the lavatory
structure.
(d) Attach the grommet 22A-150 and the bracket 22A-160 with the screws
22A-170, the washers 22A-060 and the nuts 22A-180 to the shutoff valve rod
22A-140 and to the lavatory structure.
(e) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the shutoff valve 22A-240.
For Myanmar Airways (MMA) use only
(f) Attach the angle 22A-130 with the screws 22A-050, the washers 22A-060 and
the nuts 22A-180 to the lavatory structure.
(g) Attach the brackets 22A-030 with the screws 22A-050 and the washers
22A-060 to the lavatory structure.
(h) Attach the water heater 22A-070 with the clamps 22A-040 to the brackets
22A-030.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the water heater 22A-070.
(p) Attach the tee 22A-260 to the hose 22A-270 and to the water heater 22A-070.
(r) Attach the remaining parts of the infrared faucet assembly 22A-010 with the
screws 22A-050, the washers 22A-060 and the nuts 22A-180.
(s) Attach the hoses 22A-080, 22A-090 to the water heater 22A-070, to the tee
22A-260 and to the valve of the infrared faucet assembly 22A-010.
(t) Attach the hose 22A-090 with the clamps 22A-100, the spacers 22A-110, the
screws 22A-120 and the washers 22A-060.
(u) Attach the infrared faucet assembly 22A-010 with the screw 22A-020.
(v) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the infrared faucet assembly 22A-010.
(w) Connect the infrared faucet assembly 22A-010 to the water supply and to the
electrical supply.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-805-C01
D2549010414600
17. Assembly of the Potable Water System
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-020-A01
(1) Assembly of the Potable Water System (22B-1)
(a) Attach the tube 22B-310 with the clamp 22B-340, the spacer 22B-350, the
screw 22B-400 and the washer 22B-440 to the lavatory structure.
(b) Attach the shutoff valve 22B-220 and the shutoff valve bracket 22B-250 with
the screws 22B-420 and the washers 22B-430.
(c) Attach the shutoff valve rod 22B-290 to the shutoff valve 22B-220.
(d) Attach the grommet 22B-300 and the bracket 22B-280 with the screws
22B-410, the washers 22B-440 and the nuts 22B-460 to the shutoff valve rod
22B-290 and to the lavatory structure.
(e) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the shutoff valve 22B-220.
(h) Attach the tube 22B-310 with the clamp 22B-340, the spacer 22B-350, the
screw 22B-400 and the washer 22B-440 to the lavatory structure.
(m) Attach the brackets 22B-200, the spacers 22B-180, the screws 22B-170 and
the washers 22B-160 to the lavatory structure.
(p) Attach the water heater 22B-190 with the clamps 22B-210 to the brackets
22B-200.
(q) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the water heater 22B-190.
(r) Attach the reducer elbows 22B-040, 22B-080 to the valve of water faucet
assembly 22B-010.
(s) Attach the hose 22B-050 to the reducer elbow 22B-040 and to the water heater
22B-190.
(u) Attach the hose 22B-060 with the clamps 22B-020, the spacers 22B-030,
22B-100, the screws 22B-140, 22B-150 and the washers 22B-160 to the
lavatory structure.
(v) Attach the hose 22B-060 to the tee 22B-330 and to the reducer elbow 22B-080.
(x) Attach the valve of water faucet assembly 22B-010 with the screws 22B-120
and the washers 22B-160 to the lavatory structure.
(y) Attach the cover assembly 22B-070 with the screws 22B-120 and the washers
22B-160 to the lavatory structure.
(z) Attach the controller of water faucet assembly 22B-010 with the screws
22B-120 and the washers 22B-160 to the lavatory structure.
(aa) Attach the tube of water faucet assembly 22B-010 with the clamps 22B-090,
the spacers 22B-110, the screws 22B-130 and the washers 22B-160 to the
lavatory structure.
(ab) Attach the ground cable in accordance with the Process and Material
For Myanmar Airways (MMA) use only
(ac) Connect the water faucet assembly 22B-010 to the water supply.
TASK 25-41-58-400-806-A01
A. General
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-021-A01
(1) Assembly of the Ventilation System (21-1)
(a) Attach the air extraction hood 21-130 with the screws 21-200 to the ceiling
panel.
(b) Attach the fleece 21-220, the grille 21-210 and the louver 21-140 with the
screws 21-230 to the ceiling panel.
(c) Attach the air extraction bracket 21-150 with the screws 21-160 to the ceiling
panel.
(f) Attach the tube 21-070 with the clamp 21-040 to the hose 21-080.
(g) Attach the tube 21-070 with the clamps 21-120, the screws 21-090 and the
washers 21-100 to the lavatory rear wall.
(h) Attach the hose 21-060 with the clamp 21-040 to the tube 21-070.
(j) Attach the cap 21-030 with the clamp 21-040 to the hose 21-060.
(k) Attach the individual air outlet 21-010 with the clamp 21-020 to the cap 21-030.
For Myanmar Airways (MMA) use only
(l) Attach the individual air outlet 21-010 to the lavatory structure.
TASK 25-41-58-400-806-B01
D2549026000600 D2549030812000
19. Assembly of the Ventilation System
A. General
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-022-A01
(1) Assembly of the Ventilation System (21A-1)
(a) Attach the air extraction hood 21A-130 with the screws 21A-200 to the ceiling
panel.
(b) Attach the fleece 21A-220, the grille 21A-210 and the louver 21A-140 with the
screws 21A-230 to the ceiling panel.
(c) Attach the air extraction bracket 21A-150 with the screws 21A-160 to the
ceiling panel.
(f) Attach the tube 21A-070 with the clamp 21A-040 to the hose 21A-080.
(g) Attach the tube 21A-070 with the clamps 21A-120, the screws 21A-090 and the
washers 21A-100 to the lavatory rear wall.
(h) Attach the hose 21A-060 with the clamp 21A-040 to the tube 21A-070.
(j) Attach the cap 21A-030 with the clamp 21A-040 to the hose 21A-060.
(k) Attach the individual air outlet 21A-010 with the clamp 21A-020 to the cap
21A-030.
For Myanmar Airways (MMA) use only
(l) Attach the individual air outlet 21A-010 to the lavatory structure.
TASK 25-41-58-400-807-A01
R225411620-000 R225411623-000
20. Assembly and Installation of the Nursing Table
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-400-076-A01
1 Attach the stoppers 20-060, 20-070 with the adhesive (FASTBOND 10).
(b) Attach the nursing table assembly 20-010 with the screws 20-090 to the
lavatory structure.
(c) Attach the hook assembly 20-080 with the screws 20-090, 20-095 to the
lavatory structure.
SUBTASK 25-41-58-400-076-B01
D2549020902600 D2549020908200
(0) Assembly and Installation of the Nursing Table (20-1)
2 Attach the latch assembly 20-020 with the screws 20-030, 20-035.
(b) Attach the nursing table assembly 20-010 with the screws 20-090 to the
lavatory structure.
For Myanmar Airways (MMA) use only
(c) Attach the catch 20-080 with the screws 20-090 to the lavatory structure.
TASK 25-41-58-400-807-B01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-400-075-A01
(1) Assembly and Installation of the Nursing Table (20A-1)
(b) Attach the nursing table assembly 20A-010 with the screws 20A-090 to the
lavatory structure.
(c) Attach the hook assembly 20A-080 with the screws 20A-090 to the lavatory
structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-808-A01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-400-077-A01
3 Attach the shaver outlet 19-420 with the set screw 19-430 to the bracket
19-450.
(b) Attach the passenger service unit PSU 19-360 with the set screw 19-400 to
the lower part service cabinet 19-080.
1 Attach the loaded spring latches 19-130 and the bushings 19-120 with
the washers 19-250 and the nuts 19-240 to the upper part service cabinet
assembly 19-020 and to the lower part service cabinet 19-080.
2 Attach the angle brackets 19-190 with the screws 19-200 and the washers
19-210 to the lavatory structure.
3 Attach the lower part service cabinet 19-080 with the screws 19-220 and
the washers 19-210 to the lavatory structure.
4 Attach the lower part service cabinet 19-080 with the screws 19-230 to
the angle brackets 19-190.
For Myanmar Airways (MMA) use only
5 Attach the chutes 19-155 to the lower part service cabinet 19-080.
8 Attach the hinge 19-090 with the screws 19-220 and the washers 19-210
to the lavatory structure.
9 Attach the center part service cabinet 19-070 with the hinge pin 19-100
to the hinge 19-090.
10 Attach the upper part service cabinet assembly 19-020 with the screws
19-220 and the washers 19-210 to the lavatory structure.
12 Attach the angle assemblies 19-160 with the screws 19-260, the washers
19-270 and the nuts 19-280 to the center part service cabinet 19-070.
13 Attach the block 19-030 with the screws 19-040, the washers 19-060 and
the nuts 19-050 to the upper part service cabinet assembly 19-020.
1 Attach the handle 19-340 and the handle holders 19-320 with screws
19-330.
(e) Attach the service box assembly 19-290 to the service cabinet assembly
19-010.
SUBTASK 25-41-58-400-077-B01
3 Attach the shaver outlet 19-420 with the set screw 19-430 to the bracket
19-450.
(b) Attach the passenger service unit PSU 19-360 with the set screw 19-400 to
the lower part service cabinet 19-080.
1 Attach the loaded spring latches 19-130 and the bushings 19-120 with
the washers 19-250 and the nuts 19-240 to the upper part service cabinet
assembly 19-020 and to the lower part service cabinet 19-080.
2 Attach the angle bracket 19-190 with the screws 19-205, the washers
For Myanmar Airways (MMA) use only
3 Attach the angle bracket 19-190 with the screws 19-200 and the washers
19-210 to the lavatory structure.
4 Attach the lower part service cabinet 19-080 with the screws 19-220 and
the washers 19-210 to the lavatory structure.
5 Attach the lower part service cabinet 19-080 with the screws 19-230 to
the angle brackets 19-190.
7 Attach the hinge 19-090 with the screws 19-220 and the washers 19-210
to the lavatory structure.
8 Attach the center part service cabinet 19-070 with the hinge pin 19-100
to the hinge 19-090.
9 Attach the upper part service cabinet assembly 19-020 with the screws
19-220, 19-225 and the washers 19-210 to the lavatory structure.
11 Attach the angle assemblies 19-160 with the screws 19-260, the washers
19-270 and the nuts 19-280 to the center part service cabinet 19-070.
12 Attach the block 19-030 with the screws 19-040, the washers 19-060 and
the nuts 19-050 to the upper part service cabinet assembly 19-020.
1 Attach the handle 19-340 and the handle holders 19-320 with screws
19-330.
(e) Attach the service box assembly 19-290 to the service cabinet assembly
19-010.
(f) Attach the label 19-460 and the protective film 19-470 to the service cabinet
assembly 19-010.
(g) Attach the label 19-460 to the service cabinet assembly 19-010.
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-400-077-C01
D2549020307200 D2549030708000
(0) Assembly and Installation of the Service Cabinet (19-1)
(b) Attach the passenger service unit PSU 19-360 with the set screw 19-400 to
the lower part service cabinet 19-080.
1 Attach the loaded spring latches 19-130 and the bushings 19-120 with
the washers 19-250 and the nuts 19-240 to the upper part service cabinet
assembly 19-020 and to the lower part service cabinet 19-080.
2 Attach the angle brackets 19-190 with the screws 19-200 and the washers
19-210 to the lavatory structure.
3 Attach the lower part service cabinet 19-080 with the screws 19-220 and
the washers 19-210 to the lavatory structure.
4 Attach the lower part service cabinet 19-080 with the screws 19-230 to
the angle brackets 19-190.
6 Attach the hinge 19-090 with the screws 19-220 and the washers 19-210
to the lavatory structure.
7 Attach the center part service cabinet 19-070 with the hinge pin 19-100
to the hinge 19-090.
8 Attach the upper part service cabinet assembly 19-020 with the screws
19-220 and the washers 19-210 to the lavatory structure.
For Myanmar Airways (MMA) use only
10 Attach the angle assemblies 19-160 with the screws 19-260, the washers
19-270 and the nuts 19-280 to the center part service cabinet 19-070.
11 Attach the block 19-030 with the screws 19-040, the washers 19-060 and
the nuts 19-050 to the upper part service cabinet assembly 19-020.
1 Attach the handle 19-340 and the handle holders 19-320 with screws
19-330.
(e) Attach the service box assembly 19-290 to the service cabinet assembly
19-010.
TASK 25-41-58-400-808-B01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-400-078-A01
(a) Attach the label 19A-460 with the protective film 19A-470 to the service cabinet
assembly 19A-010.
3 Attach the shaver outlet 19A-420 with the set screw 19A-430 to the
bracket 19A-450.
For Myanmar Airways (MMA) use only
(c) Attach the passenger service unit PSU 19A-360 with the set screw 19A-400 to
the lower part service cabinet 19A-080.
1 Attach the loaded spring latches 19A-130 and the bushings 19A-120 with
the washers 19A-250 and the nuts 19A-240 to the upper part service
cabinet assembly 19A-020 and to the lower part service cabinet 19A-080.
2 Attach the angle brackets 19A-190 with the screws 19A-200 and the
washers 19A-210 to the lavatory structure.
3 Attach the lower part service cabinet 19A-080 with the screws 19A-220
and the washers 19A-210 to the lavatory structure.
4 Attach the lower part service cabinet 19A-080 with the screws 19A-230 to
the angle brackets 19A-190.
5 Attach the chutes 19A-155 to the lower part service cabinet 19A-080.
8 Attach the hinge 19A-090 with the screws 19A-220 and the washers
19A-210 to the lavatory structure.
9 Attach the center part service cabinet 19A-070 with the hinge pin 19A-100
to the hinge 19A-090.
10 Attach the upper part service cabinet assembly 19A-020 with the screws
19A-220 and the washers 19A-210 to the lavatory structure.
12 Attach the angle assemblies 19A-160 with the screws 19A-260, the
washers 19A-270 and the nuts 19A-280 to the center part service cabinet
19A-070.
13 Attach the block 19A-030 with the screws 19A-040, the washers 19A-060
For Myanmar Airways (MMA) use only
and the nuts 19A-050 to the upper part service cabinet assembly 19A-020.
1 Attach the handle 19A-340 and the handle holders 19A-320 with the
screws 19A-330.
(f) Attach the service box assembly 19A-290 to the service cabinet assembly
19A-010.
SUBTASK 25-41-58-400-078-B01
3 Attach the shaver outlet 19A-420 with the set screw 19A-430 to the
bracket 19A-450.
(c) Attach the passenger service unit PSU 19A-360 with the set screw 19A-400 to
the lower part service cabinet 19A-080.
For Myanmar Airways (MMA) use only
1 Attach the loaded spring latches 19A-130 and the bushings 19A-120 with
the washers 19A-250 and the nuts 19A-240 to the upper part service
cabinet assembly 19A-020 and to the lower part service cabinet 19A-080.
2 Attach the angle brackets 19A-190 with the screws 19A-200 and the
washers 19A-210 to the lavatory structure.
3 Attach the lower part service cabinet 19A-080 with the screws 19A-220
and the washers 19A-210 to the lavatory structure.
4 Attach the lower part service cabinet 19A-080 with the screws 19A-230 to
the angle brackets 19A-190.
6 Attach the hinge 19A-090 with the screws 19A-220 and the washers
19A-210 to the lavatory structure.
7 Attach the center part service cabinet 19A-070 with the hinge pin 19A-100
to the hinge 19A-090.
8 Attach the upper part service cabinet assembly 19A-020 with the screws
19A-220 and the washers 19A-210 to the lavatory structure.
10 Attach the angle assemblies 19A-160 with the screws 19A-260, the
washers 19A-270 and the nuts 19A-280 to the center part service cabinet
19A-070.
11 Attach the block 19A-030 with the screws 19A-040, the washers 19A-060
and the nuts 19A-050 to the upper part service cabinet assembly 19A-020.
1 Attach the handle 19A-340 and the handle holders 19A-320 with the
screws 19A-330.
(f) Attach the service box assembly 19A-290 to the service cabinet assembly
19A-010.
SUBTASK 25-41-58-400-078-C01
(b) Attach the passenger service unit PSU 19A-360 with the set screw 19A-400 to
the lower part service cabinet 19A-080.
1 Attach the loaded spring latches 19A-130 and the bushings 19A-120 with
the washers 19A-250 and the nuts 19A-240 to the upper part service
cabinet assembly 19A-020 and to the lower part service cabinet 19A-080.
2 Attach the angle brackets 19A-190 with the screws 19A-200 and the
washers 19A-210 to the lavatory structure.
3 Attach the lower part service cabinet 19A-080 with the screws 19A-220
and the washers 19A-210 to the lavatory structure.
4 Attach the lower part service cabinet 19A-080 with the screws 19A-230 to
the angle brackets 19A-190.
6 Attach the hinge 19A-090 with the screws 19A-220 and the washers
For Myanmar Airways (MMA) use only
7 Attach the center part service cabinet 19A-070 with the hinge pin 19A-100
to the hinge 19A-090.
8 Attach the upper part service cabinet assembly 19A-020 with the screws
19A-220 and the washers 19A-210 to the lavatory structure.
10 Attach the angle assemblies 19A-160 with the screws 19A-260, the
washers 19A-270 and the nuts 19A-280 to the center part service cabinet
19A-070.
11 Attach the block 19A-030 with the screws 19A-040, the washers 19A-060
and the nuts 19A-050 to the upper part service cabinet assembly 19A-020.
1 Attach the handle 19A-340 and the handle holders 19A-320 with the
screws 19A-330.
(e) Attach the service box assembly 19A-290 to the service cabinet assembly
19A-010.
SUBTASK 25-41-58-400-078-D01
D2547160900800
(0) Assembly and Installation of the Service Cabinet (19A-1)
3 Attach the shaver outlet 19A-420 with the set screw 19A-430 to the
bracket 19A-450.
(b) Attach the passenger service unit PSU 19A-360 with the set screw 19A-400 to
the lower part service cabinet 19A-080.
1 Attach the loaded spring latches 19A-130 and the bushings 19A-120 with
the washers 19A-250 and the nuts 19A-240 to the upper part service
cabinet assembly 19A-020 and to the lower part service cabinet 19A-080.
2 Attach the angle brackets 19A-190 with the screws 19A-200 and the
washers 19A-210 to the lavatory structure.
3 Attach the lower part service cabinet 19A-080 with the screws 19A-220
and the washers 19A-210 to the lavatory structure.
4 Attach the lower part service cabinet 19A-080 with the screws 19A-230 to
the angle brackets 19A-190.
6 Attach the hinge 19A-090 with the screws 19A-220 and the washers
19A-210 to the lavatory structure.
7 Attach the center part service cabinet 19A-070 with the hinge pin 19A-100
to the hinge 19A-090.
8 Attach the upper part service cabinet assembly 19A-020 with the screws
19A-220 and the washers 19A-210 to the lavatory structure.
10 Attach the angle assemblies 19A-160 with the screws 19A-260, the
washers 19A-270 and the nuts 19A-280 to the center part service cabinet
19A-070.
11 Attach the block 19A-030 with the screws 19A-040, the washers 19A-060
and the nuts 19A-050 to the upper part service cabinet assembly 19A-020.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-808-C01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-400-079-A01
D2549010301000 D2549010414600
(1) Assembly and Installation of the Service Cabinet (19B-1)
3 Attach the shaver outlet 19B-420 with the set screw 19B-430 to the
bracket 19B-450.
(b) Attach the passenger service unit PSU 19B-360 with the set screw 19B-400 to
the lower part service cabinet 19B-080.
1 Attach the loaded spring latches 19B-130 and the bushings 19B-120 with
the washers 19B-250 and the nuts 19B-240 to the upper part service
cabinet assembly 19B-020 and to the lower part service cabinet 19B-080.
2 Attach the angle brackets 19B-190 with the screws 19B-200 and the
washers 19B-210 to the lavatory structure.
For Myanmar Airways (MMA) use only
3 Attach the lower part service cabinet 19B-080 with the screws 19B-220
and the washers 19B-210 to the lavatory structure.
4 Attach the lower part service cabinet 19B-080 with the screws 19B-230 to
the angle brackets 19B-190.
6 Attach the hinge 19B-090 with the screws 19B-220 and the washers
19B-210 to the lavatory structure.
7 Attach the center part service cabinet 19B-070 with the hinge pin 19B-100
to the hinge 19B-090.
8 Attach the upper part service cabinet assembly 19B-020 with the screws
19B-220 and the washers 19B-210 to the lavatory structure.
10 Attach the angle assemblies 19B-160 with the screws 19B-260, the
washers 19B-270 and the nuts 19B-280 to the center part service cabinet
19B-070.
11 Attach the block 19B-030 with the screws 19B-040, the washers 19B-060
and the nuts 19B-050 to the upper part service cabinet assembly 19B-020.
1 Attach the handle 19B-340 and the handle holders 19B-320 with the
screws 19B-330.
(e) Attach the service box assembly 19B-290 to the service cabinet assembly
19B-010.
(f) Attach the label 19B-015 and the protective film 19B-016 to the service cabinet
assembly 19B-010.
SUBTASK 25-41-58-400-079-B01
D2549010300000
For Myanmar Airways (MMA) use only
3 Attach the shaver outlet 19B-420 with the set screw 19B-430 to the
bracket 19B-450.
(b) Attach the passenger service unit PSU 19B-360 with the set screw 19B-400 to
the lower part service cabinet 19B-080.
1 Attach the loaded spring latches 19B-130 and the bushings 19B-120 with
the washers 19B-250 and the nuts 19B-240 to the upper part service
cabinet assembly 19B-020 and to the lower part service cabinet 19B-080.
2 Attach the angle brackets 19B-190 with the screws 19B-200 and the
washers 19B-210 to the lavatory structure.
3 Attach the lower part service cabinet 19B-080 with the screws 19B-220
and the washers 19B-210 to the lavatory structure.
4 Attach the lower part service cabinet 19B-080 with the screws 19B-230 to
the angle brackets 19B-190.
6 Attach the hinge 19B-090 with the screws 19B-220 and the washers
19B-210 to the lavatory structure.
7 Attach the center part service cabinet 19B-070 with the hinge pin 19B-100
to the hinge 19B-090.
8 Attach the upper part service cabinet assembly 19B-020 with the screws
19B-220 and the washers 19B-210 to the lavatory structure.
For Myanmar Airways (MMA) use only
10 Attach the angle assemblies 19B-160 with the screws 19B-260, the
washers 19B-270 and the nuts 19B-280 to the center part service cabinet
19B-070.
11 Attach the block 19B-030 with the screws 19B-040, the washers 19B-060
and the nuts 19B-050 to the upper part service cabinet assembly 19B-020.
TASK 25-41-58-400-809-A01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT YOU DO NOT BEND THE DISCHARGE TUBE
WHEN YOU REMOVE OR INSTALL THE FIRE EXTINGUISHER. IF
YOU DO, YOU CAN CAUSE DAMAGE TO THE JOINT BETWEEN THE
DISCHARGE TUBE AND THE CONTAINER.
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-028-A01
(a) Install and assemble the door ejector assembly 18-190 as follows:
1 Attach the spring 18-230 and the door ejector pin 18-210 with the hinge
pin 18-220 to the door ejector housing 18-200.
2 Attach the door ejector assembly 18-190 with the screws 18-240, the
washers 18-250 and the nuts 18-260 to the waste-box console assembly
18-060.
1 Attach the cover 18-090 with the screws 18-100, the washers 18-110 and
the nuts 18-120 to the waste-box console assembly 18-060.
For Myanmar Airways (MMA) use only
(c) Attach the waste-box console assembly 18-060 with the screws 18-140 and the
washers 18-150 to the lavatory structure.
(d) Attach the waste chute 18-010 with the screws 18-040 to the waste-box
console assembly 18-060.
(e) Attach the fire extinguisher 18-160 with the screws 18-040, the washers
18-150, 18-170 and the clip nuts 18-180.
(f) Attach the waste container 18-050 into the waste-box console assembly
18-060.
SUBTASK 25-41-58-440-028-B01
(a) Install and assemble the door ejector assembly 18-190 as follows:
1 Attach the spring 18-230 and the door ejector pin 18-210 with the hinge
pin 18-220 to the door ejector housing 18-200.
2 Attach the door ejector assembly 18-190 with the screws 18-240, the
washers 18-250 and the nuts 18-260 to the waste-box console assembly
18-060.
1 Attach the cover 18-090 with the screws 18-100, the washers 18-110 and
the nuts 18-120 to the waste-box console assembly 18-060.
(c) Attach the waste-box console assembly 18-060 with the screws 18-140 and the
washers 18-150 to the lavatory structure.
(d) Attach the waste chute 18-010 with the screws 18-040 to the waste-box
console assembly 18-060.
(e) Attach the fire extinguisher 18-160 with the screws 18-040, the washers
For Myanmar Airways (MMA) use only
(f) Attach the waste container 18-050 into the waste-box console assembly
18-060.
TASK 25-41-58-400-810-A01
R225401884-000 R225401886-000
26. Assembly and Installation of the Panel Assembly of the Washbasin Unit
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-030-A01
1 Attach the rollers 17-050 with the cable tie 17-060 to the paper-roll holder
assembly 17-040.
(b) Attach the paper-roll holder assembly 17-040 to the washbasin-unit panel
assembly 17-010.
(c) Attach the washbasin-unit panel assembly 17-010 with the screws 17-020 and
the washers 17-030 to the lavatory structure.
(d) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin-unit panel assembly 17-010.
SUBTASK 25-41-58-440-030-B01
1 Attach the rollers 17-050 with the cable tie 17-060 to the paper-roll holder
assembly 17-040.
(b) Attach the paper-roll holder assembly 17-040 to the washbasin-unit panel
assembly 17-010.
For Myanmar Airways (MMA) use only
(d) Attach the washbasin-unit panel assembly 17-010 with the screws 17-020 and
the washers 17-030 to the lavatory structure.
(e) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin-unit panel assembly 17-010.
TASK 25-41-58-400-810-B01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-031-A01
1 Attach the rollers 17A-050 with the cable tie 17A-060 to the paper-roll
holder assembly 17A-040.
(b) Attach the paper-roll holder assembly 17A-040 to the washbasin-unit panel
assembly 17A-010.
For Myanmar Airways (MMA) use only
(c) Attach the washbasin-unit panel assembly 17A-010 with the screws 17A-020
and the washers 17A-030 to the lavatory structure.
(d) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin-unit panel assembly 17A-010.
SUBTASK 25-41-58-440-031-B01
1 Attach the rollers 17A-050 with the cable tie 17A-060 to the paper-roll
holder assembly 17A-040.
(b) Attach the paper-roll holder assembly 17A-040 to the washbasin-unit panel
assembly 17A-010.
(d) Attach the washbasin-unit panel assembly 17A-010 with the screws 17A-020
and the washers 17A-030 to the lavatory structure.
(e) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin-unit panel assembly 17A-010.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-810-C01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-032-A01
1 Attach the rollers 17B-050 with the cable tie 17B-060 to the paper-roll
For Myanmar Airways (MMA) use only
(b) Attach the paper-roll holder assembly 17B-040 to the washbasin-unit panel
assembly 17B-010.
(c) Attach the washbasin-unit panel assembly 17B-010 with the screws 17B-020
and the washers 17B-030 to the lavatory structure.
(d) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin-unit panel assembly 17B-010.
SUBTASK 25-41-58-440-032-B01
1 Attach the rollers 17B-050 with the cable tie 17B-060 to the paper-roll
holder assembly 17B-040.
(b) Attach the paper-roll holder assembly 17B-040 to the washbasin-unit panel
assembly 17B-010.
(d) Attach the washbasin-unit panel assembly 17B-010 with the screws 17B-020
and the washers 17B-030 to the lavatory structure.
(e) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin-unit panel assembly 17B-010.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-810-D01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-033-A01
(1) Assembly and Installation of the Panel Assembly of the Washbasin Unit (17C-1)
1 Attach the rollers 17C-050 with the cable tie 17C-060 to the paper-roll
holder assembly 17C-040.
(b) Attach the paper-roll holder assembly 17C-040 to the washbasin-unit panel
assembly 17C-010.
(d) Attach the washbasin-unit panel assembly 17C-010 with the screws 17C-020
and the washers 17C-030 to the lavatory structure.
(e) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin-unit panel assembly 17C-010.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-810-E01
D2549010414600
30. Assembly and Installation of the Panel Assembly of the Washbasin
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-400-001-A01
(1) Assembly and Installation of the Panel Assembly of the Washbasin Unit (17D-1)
1 Attach the rollers 17D-030 with the cable tie 17D-040 to the paper-roll
holder assembly 17D-020.
(b) Attach the paper-roll holder assembly 17D-020 to the washbasin-unit panel
assembly 17D-010.
1 Attach the fittings 17D-150 with the screws 17D-130 and the washers
17D-140 to the washbasin-unit panel assembly 17D-010.
2 Attach the angle 17D-060 with the screws 17D-120 and the washers
17D-140 to the washbasin-unit panel assembly 17D-010.
3 Attach the bracket 17D-050 with the screws 17D-120 and the washers
17D-140 to the washbasin-unit panel assembly 17D-010.
4 Attach the bracket 17D-100 with the screws 17D-120 and the washers
17D-140 to the washbasin-unit panel assembly 17D-010.
(d) Attach the washbasin-unit panel assembly 17D-010 with the screws 17D-120
and the washers 17D-140 to the lavatory structure.
For Myanmar Airways (MMA) use only
(e) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin-unit panel assembly 17D-010.
TASK 25-41-58-400-811-A01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-034-A01
(1) Assembly and Installation of the Door Assembly of the Washbasin Unit (16-1)
(a) Attach the catch 16-160 with the screws 16-170 and the washers 16-130 to
the angle 16-140.
(b) Attach the sealing section 16-150 and the angle 16-140 with the screws
16-200, the washers 16-120 and the nut 16-190 to the lavatory structure.
(c) Attach the sealing section 16-150 and the angle 16-140 with the screws 16-110
and the washers 16-120 to the lavatory structure.
(e) Attach the mounting angle assembly 16-090 with the screws 16-110, 16-112,
16-113, the washers 16-180 and the nuts 16-190 to the lavatory structure.
(g) Attach the mounting angle assembly 16-070 with the screws 16-110, 16-113
and the washers 16-120 to the lavatory structure.
(h) Install and assemble the washbasin-unit door assembly 16-010 as follows:
1 Attach the latch assembly 16-050 with the screws 16-040 to the
washbasin-unit door assembly 16-010.
assembly 16-010.
3 Attach the washbasin-unit door assembly 16-010 with the attach pins
16-020, 16-030 to the mounting angle assemblies 16-070, 16-090.
TASK 25-41-58-400-811-B01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-035-A01
(1) Assembly and Installation of the Door Assembly of the Washbasin Unit (16A-1)
(a) Attach the catch 16A-160 with the screws 16A-170 and the washers 16A-130
to the angle 16A-140.
(b) Attach the sealing section 16A-150 and the angle 16A-140 with the screws
16A-200, the washers 16A-120 and the nut 16A-190 to the lavatory structure.
(c) Attach the sealing section 16A-150 and the angle 16A-140 with the screws
16A-110 and the washers 16A-120 to the lavatory structure.
(e) Attach the mounting angle assembly 16A-090 with the screw 16A-110,
16A-115, the washer 16A-180 and the nut 16A-190 to the lavatory structure.
(g) Attach the mounting angle assembly 16A-070 with the screws 16A-110 and the
washers 16A-120 to the lavatory structure.
(h) Install and assemble the washbasin-unit door assembly 16A-010 as follows:
1 Attach the latch assembly 16A-050 with the screws 16A-040 to the
washbasin-unit door assembly 16A-010.
3 Attach the washbasin-unit door assembly 16A-010 with the attach pins
16A-020, 16A-030 to the mounting angle assemblies 16A-070, 16A-090.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-811-C01
A. General
This task gives you the installation and assembly procedures of the component.
For Myanmar Airways (MMA) use only
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-036-A01
(a) Attach the catch 16B-180 with the screws 16B-190 and the washers 16B-150
to the angle 16B-160.
(b) Attach the sealing section 16B-170 and the angle 16B-160 with the screws
16B-220, the washers 16B-140 and the nut 16B-210 to the lavatory structure.
(c) Attach the sealing section 16B-170 and the angle 16B-160 with the screws
16B-130 and the washers 16B-140 to the lavatory structure.
(e) Attach the mounting angle assembly 16B-100 with the screw 16B-130, the
washer 16B-200 and the nut 16B-210 to the lavatory structure.
(g) Attach the mounting angle assembly 16B-070 with the screws 16B-130 and the
washers 16B-140 to the lavatory structure.
(h) Install and assemble the washbasin-unit door assembly 16B-010 as follows:
1 Attach the latch assembly 16B-050 with the screws 16B-040 to the
washbasin-unit door assembly 16B-010.
3 Attach the washbasin-unit door assembly 16B-010 with the attach pins
16B-020, 16B-030 to the mounting angle assemblies 16B-070, 16B-100.
SUBTASK 25-41-58-440-036-B01
D2549010300000
(0) Assembly and Installation of the Door Assembly of the Washbasin Unit (16B-1)
1 Attach the catch 16B-250 with the screw 16B-260 to the bracket catch
16B-230.
2 Attach the bracket catch 16B-230 with the screws 16B-240 to the lavatory
structure.
(b) Attach the catch 16B-180 with the screws 16B-190 and the washers 16B-150
to the angle 16B-160.
(c) Attach the sealing section 16B-170 and the angle 16B-160 with the screws
16B-220, the washers 16B-140 and the nut 16B-210 to the lavatory structure.
(d) Attach the sealing section 16B-170 and the angle 16B-160 with the screws
16B-130 and the washers 16B-140 to the lavatory structure.
For Myanmar Airways (MMA) use only
(f) Attach the mounting angle assembly 16B-100 with the screw 16B-130, the
washer 16B-200 and the nut 16B-210 to the lavatory structure.
(h) Attach the mounting angle assembly 16B-070 with the screws 16B-130 and the
washers 16B-140 to the lavatory structure.
(j) Install and assemble the washbasin-unit door assembly 16B-010 as follows:
1 Attach the latch assembly 16B-050 with the screws 16B-040 to the
washbasin-unit door assembly 16B-010.
3 Attach the washbasin-unit door assembly 16B-010 with the attach pins
16B-020, 16B-030 to the mounting angle assemblies 16B-070, 16B-100.
TASK 25-41-58-400-811-D01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-037-A01
(1) Assembly and Installation of the Door Assembly of the Washbasin Unit (16C-1)
(a) Attach the mounting angle 16C-100 with the screw 16C-120 and the washer
16C-130 to the lavatory structure.
(c) Attach the mounting angle assembly 16C-070 with the screws 16C-110 and the
washers 16C-130 to the lavatory structure.
(d) Install and assemble the washbasin-unit door assembly 16C-010 as follows:
1 Attach the latch assembly 16C-060 with the screws 16C-050 to the
washbasin-unit door assembly 16C-010.
3 Attach the washbasin-unit door assembly 16C-010 with the attach pins
16C-020, 16C-020 to the mounting angle assemblies 16C-070 and
mounting angle 16C-100.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-812-A01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-038-A01
(a) Attach the washbasin unit bracket 15-240 with the screws 15-260 and the
washers 15-220 to the lavatory structure.
(b) Attach the angles 15-270 with the screws 15-290 and the washers 15-210 to
the lavatory structure.
– Attach the axle 15-090 and the springs 15-100 with the retaining
rings 15-110 to the washbasin hinge half 15-080 and to the flap
hinge half 15-070.
b Attach the flap 15-030 with the screws 15-040 and the washers
15-050 to the flap hinge half 15-070.
2 Attach the waste flap assembly 15-020 with the screws 15-120, the
washers 15-130 and the clip nuts 15-140.
(d) Attach the washbasin assembly 15-010 with the screws 15-190 and the
washers 15-210 to the lavatory structure.
(e) Attach the washbasin assembly 15-010 with the screws 15-200, the washers
15-220 and the nuts 15-300 to the angles 15-270.
(f) Attach the washbasin assembly 15-010 with the screws 15-230, 15–235 and
the washers 15-220, 15–225 to the washbasin unit bracket 15-240.
(g) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15-010.
(h) Attach the damper 15-150 with the bolts 15-160, the washers 15-170 and the
new cotter pins 15-180 to the waste flap assembly 15-020 and to the waste
chute 18-010.
SUBTASK 25-41-58-440-038-B01
(a) Attach the washbasin unit bracket 15-240 with the screws 15-260 and the
washers 15-220 to the lavatory structure.
(b) Attach the angles 15-270 with the screws 15-290 and the washers 15-210 to
the lavatory structure.
– Attach the axle 15-090 and the springs 15-100 with the retaining
rings 15-110 to the washbasin hinge half 15-080 and to the flap
For Myanmar Airways (MMA) use only
b Attach the flap 15-030 with the screws 15-040 and the washers
15-050 to the flap hinge half 15-070.
2 Attach the waste flap assembly 15-020 with the screws 15-120, the
washers 15-130 and the clip nuts 15-140.
(d) Attach the washbasin assembly 15-010 with the screws 15-190 and the
washers 15-210 to the lavatory structure.
(e) Attach the washbasin assembly 15-010 with the screws 15-200, the washers
15-220 and the nuts 15-300 to the angles 15-270.
(f) Attach the washbasin assembly 15-010 with the screws 15-230 and the
washers 15-220 to the washbasin unit bracket 15-240.
(g) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15-010.
(h) Attach the damper 15-150 with the bolts 15-160, the washers 15-170 and the
new cotter pins 15-180 to the waste flap assembly 15-020 and to the waste
chute 18-010.
(j) Install and assemble the liquid-soap dispenser assembly 15-310 as follows:
a Attach the pump 15-330, the seal 15-350 and the nut 15-360.
2 Attach the knurled nut 15-370 and the table mounted liquid-soap
dispenser head-assembly 15-320 to the liquid-soap dispenser hose
15-390 and to the liquid-soap dispenser bottle-assembly 15-380.
(k) Attach the soap dispenser adaptor 15-445 to the washbasin assembly 15-010.
(m) Attach the liquid-soap dispenser assy 15-450 to the bracket 15-440.
(n) Attach the soap dispenser washer 15-430 to the washbasin assembly 15-010.
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-440-038-C01
D2549020303600 D2549020308000
(0) Assembly and Installation of the Washbasin Unit (15-1), (18-1)
(a) Attach the washbasin unit bracket 15-240 with the screws 15-260 and the
washers 15-220 to the lavatory structure.
(b) Attach the angles 15-270 with the screws 15-290 and the washers 15-210 to
the lavatory structure.
– Attach the axle 15-090 and the springs 15-100 with the retaining
rings 15-110 to the washbasin hinge half 15-080 and to the flap
hinge half 15-070.
b Attach the flap 15-030 with the screws 15-040 and the washers
15-050 to the flap hinge half 15-070.
2 Attach the waste flap assembly 15-020 with the screws 15-120, the
washers 15-130 and the clip nuts 15-140.
(d) Attach the washbasin assembly 15-010 with the screws 15-190 and the
washers 15-210 to the lavatory structure.
(e) Attach the washbasin assembly 15-010 with the screws 15-200, the washers
15-220 and the nuts 15-300 to the angles 15-270.
(f) Attach the washbasin assembly 15-010 with the screws 15-230 and the
washers 15-220 to the washbasin unit bracket 15-240.
(g) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15-010.
(h) Attach the damper 15-150 with the bolts 15-160, the washers 15-170 and the
For Myanmar Airways (MMA) use only
new cotter pins 15-180 to the waste flap assembly 15-020 and to the waste
chute 18-010.
(j) Attach the soap dispenser bracket 15-410 and the spacer 15-400 with the
screws 15-420 to the washbasin assembly 15-010.
TASK 25-41-58-400-812-B01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-039-A01
(a) Attach the washbasin bracket 15A-160 with the screws 15A-140 and the
washers 15A-150 to the lavatory structure.
(b) Attach the angles 15A-170 with the screws 15A-140 and the washers 15A-130
to the lavatory structure.
(c) Attach the bracket 15A-220 with the screw 15A-120 and the washer 15A-150 to
the lavatory structure.
a Attach the pins 15A-060 and the springs 15A-080 with the splints
15A-070 to the flap 15A-050.
2 Attach the flap assembly 15A-040 with the screws 15A-090, the washers
15A-100 and the nuts 15A-110 to the washbasin 15A-030.
(e) Attach the rear cover 15A-020 and the washbasin 15A-030 with the screws
15A-120 and the washers 15A-130 to the lavatory structure.
(f) Attach the washbasin assembly 15A-010 with the screws 15A-120 and the
washers 15A-150 to the angles 15A-170.
(g) Attach the washbasin assembly 15A-010 with the screw 15A-190, the washers
15A-200 and the nut 15A-210 to the washbasin bracket 15A-160.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15A-010.
SUBTASK 25-41-58-440-039-B01
D2549010407400 R225401823-000
(0) Assembly and Installation of the Washbasin Unit (15A-1)
(a) Attach the washbasin bracket 15A-160 with the screws 15A-140 and the
washers 15A-150 to the lavatory structure.
(b) Attach the angles 15A-170 with the screws 15A-140 and the washers 15A-130
to the lavatory structure.
(c) Attach the bracket 15A-220 with the screw 15A-120 and the washer 15A-150 to
the lavatory structure.
a Attach the pins 15A-060 and the springs 15A-080 with the splints
15A-070 to the flap 15A-050.
2 Attach the flap assembly 15A-040 with the screws 15A-090, the washers
15A-100 and the nuts 15A-110 to the washbasin 15A-030.
For Myanmar Airways (MMA) use only
(e) Attach the rear cover 15A-020 and the washbasin 15A-030 with the screws
15A-120 and the washers 15A-130 to the lavatory structure.
(f) Attach the washbasin assembly 15A-010 with the screws 15A-120 and the
washers 15A-150 to the angles 15A-170.
(g) Attach the washbasin assembly 15A-010 with the screw 15A-190, the washers
15A-200 and the nut 15A-210 to the washbasin bracket 15A-160.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15A-010.
(j) Attach the liquid-soap dispenser support 15A-350 to the washbasin assembly
15A-010.
SUBTASK 25-41-58-440-039-C01
(a) Attach the washbasin bracket 15A-160 with the screws 15A-140 and the
washers 15A-150 to the lavatory structure.
(b) Attach the angles 15A-170 with the screws 15A-140 and the washers 15A-130
to the lavatory structure.
(c) Attach the bracket 15A-220 with the screw 15A-120 and the washer 15A-150 to
the lavatory structure.
a Attach the pins 15A-060 and the springs 15A-080 with the splints
15A-070 to the flap 15A-050.
For Myanmar Airways (MMA) use only
2 Attach the flap assembly 15A-040 with the screws 15A-090, the washers
15A-100 and the nuts 15A-110 to the washbasin 15A-030.
(e) Attach the rear cover 15A-020 and the washbasin 15A-030 with the screws
15A-120 and the washers 15A-130 to the lavatory structure.
(f) Attach the washbasin assembly 15A-010 with the screws 15A-120 and the
washers 15A-150 to the angles 15A-170.
(g) Attach the washbasin assembly 15A-010 with the screw 15A-190, the washers
15A-200 and the nut 15A-210 to the washbasin bracket 15A-160.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15A-010.
(j) Install and assemble the liquid-soap dispenser assembly 15A-260 as follows:
a Attach the pump 15A-280, the seal 15A-300 and the nut 15A-310.
2 Attach the knurled nut 15A-320 and the table mounted liquid-soap
dispenser head-assembly 15A-270 to the liquid-soap dispenser hose
15A-340 and to the liquid-soap dispenser bottle-assembly 15A-330.
TASK 25-41-58-400-812-C01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-040-A01
D2549020307200 D2549030708000
(1) Assembly and Installation of the Washbasin Unit (15B-1), (18-1)
(a) Attach the washbasin unit bracket 15B-290 with the screws 15B-320 and the
washers 15B-240 to the lavatory structure.
(b) Attach the angles 15B-270 with the screws 15B-260 and the washers 15B-210
to the lavatory structure.
(c) Attach the brackets 15B-170 with the screws 15B-180 and the washers
15B-190 to the washbasin 15B-020.
– Attach the axle 15B-100 and the springs 15B-110 with the
retaining rings 15B-120 to the washbasin hinge half 15B-090 and
to the flap hinge half 15B-080.
b Attach the flap 15B-040 with the screws 15B-050 and the washers
15B-060 to the flap hinge half 15B-080.
2 Attach the waste flap assembly 15B-030 with the screws 15B-130, the
washers 15B-140 and the clip nuts 15B-150 to the washbasin 15B-020.
(e) Attach the washbasin assembly 15B-010 with the screws 15B-200 and the
washers 15B-210 to the lavatory structure.
(f) Attach the washbasin assembly 15B-010 with the screws 15B-230, the washers
15B-240 and the nuts 15B-250 to the angles 15B-270.
For Myanmar Airways (MMA) use only
(g) Attach the washbasin assembly 15B-010 with the screws 15B-310 and the
washers 15B-240 to the washbasin unit bracket 15B-290.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15B-010.
(j) Attach the damper 15B-330 with the bolts 15B-340, the washers 15B-350 and
the new cotter pins 15B-360 to the waste flap assembly 15B-030 and to the
waste chute 18-010.
SUBTASK 25-41-58-440-040-B01
(a) Attach the washbasin unit bracket 15B-290 with the screws 15B-320 and the
washers 15B-240 to the lavatory structure.
(b) Attach the angles 15B-270 with the screws 15B-260 and the washers 15B-210
to the lavatory structure.
(c) Attach the brackets 15B-170 with the screws 15B-180 and the washers
15B-190 to the washbasin 15B-020.
– Attach the axle 15B-100 and the springs 15B-110 with the
retaining rings 15B-120 to the washbasin hinge half 15B-090 and
to the flap hinge half 15B-080.
b Attach the flap 15B-040 with the screws 15B-050 and the washers
15B-060 to the flap hinge half 15B-080.
2 Attach the waste flap assembly 15B-030 with the screws 15B-130, the
washers 15B-140 and the clip nuts 15B-150 to the washbasin 15B-020.
(e) Attach the washbasin assembly 15B-010 with the screws 15B-200 and the
washers 15B-210 to the lavatory structure.
(f) Attach the washbasin assembly 15B-010 with the screws 15B-230, the washers
15B-240 and the nuts 15B-250 to the angles 15B-270.
(g) Attach the washbasin assembly 15B-010 with the screws 15B-310 and the
washers 15B-240 to the washbasin unit bracket 15B-290.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15B-010.
(j) Attach the damper 15B-330 with the bolts 15B-340, the washers 15B-350 and
the new cotter pins 15B-360 to the waste flap assembly 15B-030 and to the
waste chute 18-010.
(k) Install and assemble the liquid-soap dispenser assembly 15B-380 as follows:
a Attach the pump 15B-400, the seal 15B-420, the nut 15B-430 and
the knurled nut 15B-440.
SUBTASK 25-41-58-440-040-C01
For Myanmar Airways (MMA) use only
(a) Attach the washbasin unit bracket 15B-290 with the screws 15B-320 and the
washers 15B-240 to the lavatory structure.
(b) Attach the angles 15B-270 with the screws 15B-260 and the washers 15B-210
to the lavatory structure.
(c) Attach the brackets 15B-170 with the screws 15B-180 and the washers
15B-190 to the washbasin 15B-020.
– Attach the axle 15B-100 and the springs 15B-110 with the
retaining rings 15B-120 to the washbasin hinge half 15B-090 and
to the flap hinge half 15B-080.
b Attach the flap 15B-040 with the screws 15B-050 and the washers
15B-060 to the flap hinge half 15B-080.
2 Attach the waste flap assembly 15B-030 with the screws 15B-130, the
washers 15B-140 and the clip nuts 15B-150 to the washbasin 15B-020.
(e) Attach the washbasin assembly 15B-010 with the screws 15B-200 and the
washers 15B-210 to the lavatory structure.
(f) Attach the washbasin assembly 15B-010 with the screws 15B-230, the washers
15B-240 and the nuts 15B-250 to the angles 15B-270.
(g) Attach the washbasin assembly 15B-010 with the screws 15B-310 and the
washers 15B-240 to the washbasin unit bracket 15B-290.
(h) Attach the ground cable in accordance with the Process and Material
For Myanmar Airways (MMA) use only
(j) Attach the damper 15B-330 with the bolts 15B-340, the washers 15B-350 and
the new cotter pins 15B-360 to the waste flap assembly 15B-030 and to the
waste chute 18-010.
(k) Attach the liquid-soap dispenser support 15B-370 to the washbasin assembly
15B-010.
SUBTASK 25-41-58-440-040-D01
(a) Attach the washbasin unit bracket 15B-290 with the screws 15B-320 and the
washers 15B-240 to the lavatory structure.
(b) Attach the angles 15B-270 with the screws 15B-260 and the washers 15B-210
to the lavatory structure.
(c) Attach the brackets 15B-170 with the screws 15B-180 and the washers
15B-190 to the washbasin 15B-020.
– Attach the axle 15B-100 and the springs 15B-110 with the
retaining rings 15B-120 to the washbasin hinge half 15B-090 and
to the flap hinge half 15B-080.
b Attach the flap 15B-040 with the screws 15B-050 and the washers
15B-060 to the flap hinge half 15B-080.
2 Attach the waste flap assembly 15B-030 with the screws 15B-130, the
washers 15B-140 and the clip nuts 15B-150 to the washbasin 15B-020.
For Myanmar Airways (MMA) use only
(e) Attach the washbasin assembly 15B-010 with the screws 15B-200 and the
washers 15B-210 to the lavatory structure.
(f) Attach the washbasin assembly 15B-010 with the screws 15B-230, the washers
15B-240 and the nuts 15B-250 to the angles 15B-270.
(g) Attach the washbasin assembly 15B-010 with the screws 15B-310 and the
washers 15B-240 to the washbasin unit bracket 15B-290.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15B-010.
(j) Attach the damper 15B-330 with the bolts 15B-340, the washers 15B-350 and
the new cotter pins 15B-360 to the waste flap assembly 15B-030 and to the
waste chute 18-010.
(k) Attach the liquid-soap dispenser support 15B-370 to the washbasin assembly
15B-010.
(l) Attach the liquid-soap dispenser bottle 15B-220 to the liquid-soap dispenser
support 15B-370.
SUBTASK 25-41-58-440-040-E01
(a) Attach the washbasin unit bracket 15B-290 with the screws 15B-320 and the
washers 15B-240 to the lavatory structure.
(b) Attach the angles 15B-270 with the screws 15B-260 and the washers 15B-210
to the lavatory structure.
(c) Attach the brackets 15B-170 with the screws 15B-180 and the washers
15B-190 to the washbasin 15B-020.
– Attach the axle 15B-100 and the springs 15B-110 with the
retaining rings 15B-120 to the washbasin hinge half 15B-090 and
to the flap hinge half 15B-080.
b Attach the flap 15B-040 with the screws 15B-050 and the washers
15B-060 to the flap hinge half 15B-080.
2 Attach the waste flap assembly 15B-030 with the screws 15B-130, the
washers 15B-140 and the clip nuts 15B-150 to the washbasin 15B-020.
(e) Attach the washbasin assembly 15B-010 with the screws 15B-200 and the
washers 15B-210 to the lavatory structure.
(f) Attach the washbasin assembly 15B-010 with the screws 15B-230, the washers
15B-240 and the nuts 15B-250 to the angles 15B-270.
(g) Attach the washbasin assembly 15B-010 with the screws 15B-310 and the
washers 15B-240 to the washbasin unit bracket 15B-290.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15B-010.
(j) Attach the damper 15B-330 with the bolts 15B-340, the washers 15B-350 and
the new cotter pins 15B-360 to the waste flap assembly 15B-030 and to the
waste chute 18-010.
(k) Install and assemble the liquid-soap dispenser assembly 15B-380 as follows:
a Attach the pump 15B-400, the seal 15B-420, the nut 15B-430 and
the knurled nut 15B-440.
(l) Attach the liquid-soap dispenser support 15B-370 to the washbasin assembly
For Myanmar Airways (MMA) use only
15B-010.
TASK 25-41-58-400-812-D01
R225411620-000 R225411623-000
38. Assembly and Installation of the Washbasin Unit
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-041-A01
D2549020911000 D2549020913800
(1) Assembly and Installation of the Washbasin Unit (15C-1), (18-1)
(a) Attach the washbasin unit bracket 15C-240 with the screws 15C-260 and the
washers 15C-200 to the lavatory structure.
(b) Attach the angles 15C-270 with the screws 15C-290 and the washers 15C-200
to the lavatory structure.
– Attach the axle 15C-090 and the springs 15C-100 with the
retaining rings 15C-110 to the washbasin hinge half 15C-080 and
to the flap hinge half 15C-070.
b Attach the flap 15C-030 with the screws 15C-040 and the washers
15C-050 to the flap hinge half 15C-070.
2 Attach the waste flap assembly 15C-020 with the screws 15C-120, the
washers 15C-130 and the clip nuts 15C-140.
(d) Attach the washbasin assembly 15C-010 with the screws 15C-190 and the
washers 15C-200 to the lavatory structure.
(e) Attach the washbasin assembly 15C-010 with the screws 15C-210, the
washers 15C-220 and the nuts 15C-300 to the angles 15C-270.
(f) Attach the washbasin assembly 15C-010 with the screws 15C-310 and the
washers 15C-220 to the washbasin unit bracket 15C-240.
(g) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15C-010.
(h) Attach the damper 15C-150 with the bolts 15C-160, the washers 15C-170 and
the new cotter pins 15C-180 to the waste flap assembly 15C-020 and to the
waste chute 18-010.
SUBTASK 25-41-58-440-041-B01
(a) Attach the washbasin unit bracket 15C-240 with the screws 15C-260 and the
washers 15C-200 to the lavatory structure.
(b) Attach the angles 15C-270 with the screws 15C-290 and the washers 15C-200
to the lavatory structure.
– Attach the axle 15C-090 and the springs 15C-100 with the
retaining rings 15C-110 to the washbasin hinge half 15C-080 and
to the flap hinge half 15C-070.
b Attach the flap 15C-030 with the screws 15C-040 and the washers
15C-050 to the flap hinge half 15C-070.
2 Attach the waste flap assembly 15C-020 with the screws 15C-120, the
washers 15C-130 and the clip nuts 15C-140.
(d) Attach the washbasin assembly 15C-010 with the screws 15C-190 and the
washers 15C-200 to the lavatory structure.
(e) Attach the washbasin assembly 15C-010 with the screws 15C-210, the
washers 15C-220 and the nuts 15C-300 to the angles 15C-270.
(f) Attach the washbasin assembly 15C-010 with the screws 15C-310 and the
washers 15C-220 to the washbasin unit bracket 15C-240.
(g) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15C-010.
(h) Attach the damper 15C-150 with the bolts 15C-160, the washers 15C-170 and
the new cotter pins 15C-180 to the waste flap assembly 15C-020 and to the
waste chute 18-010.
For Myanmar Airways (MMA) use only
(j) Install and assemble the liquid-soap dispenser assembly 15C-330 as follows:
a Attach the pump 15C-350, the seal 15C-370 and the nut 15C-380.
2 Attach the knurled nut 15C-390 and the table mounted liquid-soap
dispenser head-assembly 15C-340 to the liquid-soap dispenser hose
15C-410 and to the liquid-soap dispenser bottle-assembly 15C-400.
(k) Attach the soap dispenser washer 15C-420 to the washbasin assembly
15C-010.
SUBTASK 25-41-58-440-041-C01
(a) Attach the washbasin unit bracket 15C-240 with the screws 15C-260 and the
washers 15C-200 to the lavatory structure.
(b) Attach the angles 15C-270 with the screws 15C-290 and the washers 15C-200
to the lavatory structure.
– Attach the axle 15C-090 and the springs 15C-100 with the
retaining rings 15C-110 to the washbasin hinge half 15C-080 and
to the flap hinge half 15C-070.
b Attach the flap 15C-030 with the screws 15C-040 and the washers
For Myanmar Airways (MMA) use only
2 Attach the waste flap assembly 15C-020 with the screws 15C-120, the
washers 15C-130 and the clip nuts 15C-140.
(d) Attach the washbasin assembly 15C-010 with the screws 15C-190 and the
washers 15C-200 to the lavatory structure.
(e) Attach the washbasin assembly 15C-010 with the screws 15C-210, the
washers 15C-220 and the nuts 15C-300 to the angles 15C-270.
(f) Attach the washbasin assembly 15C-010 with the screws 15C-310 and the
washers 15C-220 to the washbasin unit bracket 15C-240.
(g) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15C-010.
(h) Attach the damper 15C-150 with the bolts 15C-160, the washers 15C-170 and
the new cotter pins 15C-180 to the waste flap assembly 15C-020 and to the
waste chute 18-010.
(j) Attach the liquid-soap dispenser support 15C-320 to the washbasin assembly
15C-010.
SUBTASK 25-41-58-440-041-D01
(a) Attach the washbasin unit bracket 15C-240 with the screws 15C-260 and the
washers 15C-200 to the lavatory structure.
(b) Attach the angles 15C-270 with the screws 15C-290 and the washers 15C-200
to the lavatory structure.
– Attach the axle 15C-090 and the springs 15C-100 with the
retaining rings 15C-110 to the washbasin hinge half 15C-080 and
to the flap hinge half 15C-070.
b Attach the flap 15C-030 with the screws 15C-040 and the washers
15C-050 to the flap hinge half 15C-070.
2 Attach the waste flap assembly 15C-020 with the screws 15C-120, the
washers 15C-130 and the clip nuts 15C-140.
(d) Attach the washbasin assembly 15C-010 with the screws 15C-190 and the
washers 15C-200 to the lavatory structure.
(e) Attach the washbasin assembly 15C-010 with the screws 15C-210, the
washers 15C-220 and the nuts 15C-300 to the angles 15C-270.
(f) Attach the washbasin assembly 15C-010 with the screws 15C-310 and the
washers 15C-220 to the washbasin unit bracket 15C-240.
(g) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15C-010.
(h) Attach the damper 15C-150 with the bolts 15C-160, the washers 15C-170 and
the new cotter pins 15C-180 to the waste flap assembly 15C-020 and to the
waste chute 18-010.
(j) Attach the liquid-soap dispenser support 15C-320 to the washbasin assembly
15C-010.
(k) Attach the liquid-soap dispenser bottle 15C-230 to the liquid-soap dispenser
support 15C-320.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-812-E01
D2547160900800 D2549020900600
39. Assembly and Installation of the Washbasin Unit
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-042-A01
(1) Assembly and Installation of the Washbasin Unit (15C-1), (18-1)
(a) Attach the washbasin bracket 15D-160 with the screws 15D-140 and the
washers 15D-150 to the lavatory structure.
(b) Attach the angles 15D-170 with the screws 15D-140 and the washers 15D-130
to the lavatory structure.
(c) Attach the bracket 15D-220 with the screw 15D-120 and the washer 15D-150
to the lavatory structure.
a Attach the pins 15D-060 and the springs 15D-080 with the splints
15D-070 to the flap 15D-050.
2 Attach the flap assembly 15D-040 with the screws 15D-090, the washers
15D-100 and the nuts 15D-110 to the washbasin 15D-030.
(e) Attach the rear cover 15D-020 and the washbasin 15D-030 with the screws
15D-120 and the washers 15D-130 to the lavatory structure.
For Myanmar Airways (MMA) use only
(f) Attach the washbasin assembly 15D-010 with the screws 15D-120 and the
washers 15D-150 to the angles 15D-170.
(g) Attach the washbasin assembly 15D-010 with the screw 15D-190, the washers
15D-200 and the nut 15D-210 to the washbasin bracket 15D-160.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15D-010.
(j) Attach the damper 15D-350 with the bolts 15D-360, the washers 15D-370
and the new cotter pins 15D-380 to the flap assembly 15D-040 and to the
waste chute 18-010.
(k) Install and assemble the liquid-soap dispenser assembly 15D-260 as follows:
a Attach the pump 15D-280, the seal 15D-300 and the nut 15D-310.
2 Attach the knurled nut 15D-320 and the table mounted liquid-soap
dispenser head-assembly 15D-270 to the liquid-soap dispenser hose
15D-340 and to the liquid-soap dispenser bottle-assembly 15D-330.
TASK 25-41-58-400-812-F01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
For Myanmar Airways (MMA) use only
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-043-A01
(a) Attach the washbasin unit bracket 15E-280 with the screws 15E-310 and the
washers 15E-230 to the lavatory structure.
(b) Attach the angles 15E-260 with the screws 15E-250 and the washers 15E-210
to the lavatory structure.
(c) Attach the brackets 15E-170 with the screws 15E-180 and the washers
15E-190 to the washbasin 15E-020.
– Attach the axle 15E-100 and the springs 15E-110 with the
retaining rings 15E-120 to the washbasin hinge half 15E-090 and
to the flap hinge half 15E-080.
b Attach the flap 15E-040 with the screws 15E-050 and the washers
15E-060 to the flap hinge half 15E-080.
2 Attach the waste flap assembly 15E-030 with the screws 15E-130, the
washers 15E-140 and the clip nuts 15E-150 to the washbasin 15E-020.
(e) Attach the washbasin assembly 15E-010 with the screws 15E-200 and the
washers 15E-210 to the lavatory structure.
(f) Attach the washbasin assembly 15E-010 with the screws 15E-220, the washers
15E-230 and the nuts 15E-240 to the angles 15E-260.
(g) Attach the washbasin assembly 15E-010 with the screws 15E-300 and the
washers 15E-230 to the washbasin unit bracket 15E-280.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15E-010.
(j) Attach the damper 15E-320 with the bolts 15E-330, the washers 15E-340 and
the new cotter pins 15E-350 to the waste flap assembly 15E-030 and to the
waste chute 18-010.
(k) Install and assemble the liquid-soap dispenser assembly 15E-360 as follows:
a Attach the pump 15E-380, the seal 15E-400, the nut 15E-410 and
the knurled nut 15E-420.
SUBTASK 25-41-58-440-043-B01
For Myanmar Airways (MMA) use only
D2549030810600 R225401889-002
(0) Assembly and Installation of the Washbasin Unit (15C-1), (18-1)
(a) Attach the washbasin unit bracket 15E-280 with the screws 15E-310 and the
washers 15E-230 to the lavatory structure.
(b) Attach the angles 15E-260 with the screws 15E-250 and the washers 15E-210
to the lavatory structure.
(c) Attach the brackets 15E-170 with the screws 15E-180 and the washers
15E-190 to the washbasin 15E-020.
– Attach the axle 15E-100 and the springs 15E-110 with the
retaining rings 15E-120 to the washbasin hinge half 15E-090 and
to the flap hinge half 15E-080.
b Attach the flap 15E-040 with the screws 15E-050 and the washers
15E-060 to the flap hinge half 15E-080.
2 Attach the waste flap assembly 15E-030 with the screws 15E-130, the
washers 15E-140 and the clip nuts 15E-150 to the washbasin 15E-020.
(e) Attach the washbasin assembly 15E-010 with the screws 15E-200 and the
washers 15E-210 to the lavatory structure.
(f) Attach the washbasin assembly 15E-010 with the screws 15E-220, the washers
15E-230 and the nuts 15E-240 to the angles 15E-260.
(g) Attach the washbasin assembly 15E-010 with the screws 15E-300 and the
washers 15E-230 to the washbasin unit bracket 15E-280.
(h) Attach the ground cable in accordance with the Process and Material
For Myanmar Airways (MMA) use only
(j) Attach the damper 15E-320 with the bolts 15E-330, the washers 15E-340 and
the new cotter pins 15E-350 to the waste flap assembly 15E-030 and to the
waste chute 18-010.
(k) Attach the liquid-soap dispenser support 15E-450 to the washbasin assembly
15E-010.
SUBTASK 25-41-58-440-043-C01
(a) Attach the washbasin unit bracket 15E-280 with the screws 15E-310 and the
washers 15E-230 to the lavatory structure.
(b) Attach the angles 15E-260 with the screws 15E-250 and the washers 15E-210
to the lavatory structure.
(c) Attach the brackets 15E-170 with the screws 15E-180 and the washers
15E-190 to the washbasin 15E-020.
– Attach the axle 15E-100 and the springs 15E-110 with the
retaining rings 15E-120 to the washbasin hinge half 15E-090 and
to the flap hinge half 15E-080.
b Attach the flap 15E-040 with the screws 15E-050 and the washers
15E-060 to the flap hinge half 15E-080.
2 Attach the waste flap assembly 15E-030 with the screws 15E-130, the
washers 15E-140 and the clip nuts 15E-150 to the washbasin 15E-020.
(e) Attach the washbasin assembly 15E-010 with the screws 15E-200 and the
For Myanmar Airways (MMA) use only
(f) Attach the washbasin assembly 15E-010 with the screws 15E-220, the washers
15E-230 and the nuts 15E-240 to the angles 15E-260.
(g) Attach the washbasin assembly 15E-010 with the screws 15E-300 and the
washers 15E-230 to the washbasin unit bracket 15E-280.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15E-010.
(j) Attach the damper 15E-320 with the bolts 15E-330, the washers 15E-340 and
the new cotter pins 15E-350 to the waste flap assembly 15E-030 and to the
waste chute 18-010.
(k) Attach the liquid-soap dispenser support 15E-450 to the washbasin assembly
15E-010.
(l) Attach the liquid-soap dispenser bottle 15E-460 to the liquid-soap dispenser
support 15E-450.
TASK 25-41-58-400-812-G01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-044-A01
D2549026001200
(1) Assembly and Installation of the Washbasin Unit (15F-1), (18-1)
(a) Attach the washbasin unit bracket 15F-240 with the screws 15F-260 and the
washers 15F-200 to the lavatory structure.
(b) Attach the angles 15F-270 with the screws 15F-290 and the washers 15F-200
to the lavatory structure.
– Attach the axle 15F-090 and the springs 15F-100 with the
retaining rings 15F-110 to the washbasin hinge half 15F-080 and
to the flap hinge half 15F-070.
b Attach the flap 15F-030 with the screws 15F-040 and the washers
For Myanmar Airways (MMA) use only
2 Attach the waste flap assembly 15F-020 with the screws 15F-120, the
washers 15F-130 and the clip nuts 15F-140.
(d) Attach the washbasin assembly 15F-010 with the screws 15F-190 and the
washers 15F-200 to the lavatory structure.
(e) Attach the washbasin assembly 15F-010 with the screws 15F-210, the washers
15F-220 and the nuts 15F-300 to the angles 15F-270.
(f) Attach the washbasin assembly 15F-010 with the screws 15F-310 and the
washers 15F-220 to the washbasin unit bracket 15F-240.
(g) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15F-010.
(h) Attach the damper 15F-150 with the bolts 15F-160, the washers 15F-170 and
the new cotter pins 15F-180 to the waste flap assembly 15F-020 and to the
waste chute 18-010.
(j) Install and assemble the liquid-soap dispenser assembly 15F-330 as follows:
a Attach the pump 15F-350, the seal 15F-370 and the nut 15F-380.
2 Attach the knurled nut 15F-390 and the table mounted liquid-soap
dispenser head-assembly 15F-340 to the liquid-soap dispenser hose
15F-410 and to the liquid-soap dispenser bottle-assembly 15F-400.
SUBTASK 25-41-58-440-044-B01
(a) Attach the washbasin unit bracket 15F-240 with the screws 15F-260 and the
washers 15F-200 to the lavatory structure.
(b) Attach the angles 15F-270 with the screws 15F-290 and the washers 15F-200
to the lavatory structure.
For Myanmar Airways (MMA) use only
– Attach the axle 15F-090 and the springs 15F-100 with the
retaining rings 15F-110 to the washbasin hinge half 15F-080 and
to the flap hinge half 15F-070.
b Attach the flap 15F-030 with the screws 15F-040 and the washers
15F-050 to the flap hinge half 15F-070.
2 Attach the waste flap assembly 15F-020 with the screws 15F-120, the
washers 15F-130 and the clip nuts 15F-140.
(d) Attach the washbasin assembly 15F-010 with the screws 15F-190 and the
washers 15F-200 to the lavatory structure.
(e) Attach the washbasin assembly 15F-010 with the screws 15F-210, the washers
15F-220 and the nuts 15F-300 to the angles 15F-270.
(f) Attach the washbasin assembly 15F-010 with the screws 15F-310 and the
washers 15F-220 to the washbasin unit bracket 15F-240.
(g) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15F-010.
(h) Attach the damper 15F-150 with the bolts 15F-160, the washers 15F-170 and
the new cotter pins 15F-180 to the waste flap assembly 15F-020 and to the
waste chute 18-010.
(j) Attach the liquid-soap dispenser support 15F-320 to the washbasin assembly
15F-010.
(k) Attach the liquid-soap dispenser bottle 15F-230 to the liquid-soap dispenser
support 15F-320.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-812-H01
D2549010414600
42. Assembly and Installation of the Washbasin Unit
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-400-002-A01
(1) Assembly and Installation of the Washbasin Unit (15G-1)
(a) Attach the washbasin unit bracket 15G-230 with the screws 15G-270 and the
washers 15G-310 to the lavatory structure.
(b) Attach the screws 15G-140 and the washers 15G-170 to the washbasin
15G-020.
– Attach the axle 15G-110 and the springs 15G-120 with the
retaining rings 15G-130 to the washbasin hinge half 15G-100 and
to the flap hinge half 15G-090.
b Attach the flap 15G-050 with the screws 15G-060 and the washers
15G-070 to the flap hinge half 15G-090.
For Myanmar Airways (MMA) use only
2 Attach the waste flap assembly 15G-040 with the screws 15G-150, the
washers 15G-160 and the clip nuts 15G-180 to the washbasin 15G-020.
(d) Attach the washbasin assembly 15G-010 with the screws 15G-250 and the
washers 15G-330 to the lavatory structure.
(e) Attach the washbasin assembly 15G-010 with the screws 15G-260 and the
washers 15G-310 to the lavatory structure.
(f) Attach the washbasin assembly 15G-010 with the screws 15G-250, the
washers 15G-330 and the nuts 15G-350.
(g) Attach the washbasin assembly 15G-010 with the screws 15G-250 and the
washers 15G-310 to the washbasin unit bracket 15G-230.
(h) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the washbasin assembly 15G-010.
(j) Attach the cosmetics holder 15G-200 with the screws 15G-290, the washers
15G-300 and the spacer 15G-210 to the washbasin assembly 15G-010.
(k) Attach the soap dispenser holder 15G-190 with the washers 15G-320 and the
nuts 15G-340 to the washbasin assembly 15G-010.
(l) Attach the vase 15G-220 with the screws 15G-280 to the washbasin assembly
15G-010.
TASK 25-41-58-400-813-A01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-045-A01
(a) Attach the ballast unit 14-100 and the reflector 14-060 with the screws 14-070,
14-075 and the washers 14-080 to the lavatory structure.
(b) Attach the fluorescent lamp 14-090 to the ballast unit 14-100.
(c) Attach the double-spring ball catches 14-030 with the screws 14-040 and the
washers 14-050 to the lavatory structure.
(d) Attach the lamp cover assembly 14-010 to the double-spring ball catches
14-030.
SUBTASK 25-41-58-440-045-B01
(a) Attach the advanced-integrated ballast unit 14-100, the spacers 14-110, 14-120
and the reflector 14-060 with the screws 14-070, 14-075 and the washers
14-080 to the lavatory structure.
(b) Attach the fluorescent lamp 14-090 to the advanced-integrated ballast unit
14-100.
(c) Attach the double-spring ball catches 14-030 with the screws 14-040 and the
washers 14-050 to the lavatory structure.
(d) Attach the lamp cover assembly 14-010 to the double-spring ball catches
For Myanmar Airways (MMA) use only
14-030.
TASK 25-41-58-400-813-B01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-046-A01
(a) Attach the ballast unit 14A-100 and the reflector 14A-060 with the screws
14A-070, 14A-075 and the washers 14A-080 to the lavatory structure.
(b) Attach the fluorescent lamp 14A-090 to the ballast unit 14A-100.
(c) Attach the double-spring ball catches 14A-030 with the screws 14A-040 and
the washers 14A-050 to the lavatory structure.
(d) Attach the lamp cover assembly 14A-010 to the double-spring ball catches
14A-030.
SUBTASK 25-41-58-440-046-B01
(a) Attach the advanced-integrated ballast unit 14A-100, the spacers 14A-110,
14A-120 and the reflector 14A-060 with the screws 14A-070, 14A-075 and the
washers 14A-080 to the lavatory structure.
(b) Attach the fluorescent lamp 14A-090 to the advanced integrated-ballast unit
14A-100.
(c) Attach the double-spring ball catches 14A-030 with the screws 14A-040 and
the washers 14A-050 to the lavatory structure.
(d) Attach the lamp cover assembly 14A-010 to the double-spring ball catches
14A-030.
TASK 25-41-58-400-813-C01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-440-045-D01
(b) Attach the brackets 14B-050 with the screws 14B-080 and the washers
14B-090 to the lavatory structure.
(c) Attach the part of the double-spring ball catches 14B-030 with the screws
14B-060 and the washers 14B-070 to the lavatory structure.
(d) Attach the lamp cover assembly 14B-010 to the part of the double-spring ball
catches 14B-030.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-814-A01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-001-A01
1 Attach the floor-panel end strip 13-040 with the screws 13-050 to the
floor panel assembly 13-030.
(b) Attach the floor panel assembly 13-030 with the screws 13-180 to the lavatory
structure.
(c) Attach the angle 13-120 with the screws 13-130 and the washers 13-140 to the
floor panel assembly 13-030.
(d) Attach the angles 13-090, 13-100 with the screws 13-110 to the floor panel
assembly 13-030.
(e) Attach the angles 13-150 with the screws 13-160, the washers 13-140 and the
nuts 13-170 to the floor-panel end strip 13-040.
(f) Attach the screws 13-190, 13-210 and the washers 13-200, 13-220, 13-230 to
the angles 13-090, 13-100, 13-120 and to the lavatory structure.
SUBTASK 25-41-58-410-001-B01
(a) Attach the floor panel assembly 13-030 with the screws 13-180 to the lavatory
structure.
(b) Attach the angle 13-120 with the screws 13-130 and the washers 13-141 to the
floor panel assembly 13-030.
(c) Attach the angles 13-090, 13-100 with the screws 13-110 to the floor panel
assembly 13-030.
(d) Attach the floor pan 13-010 with the screws 13-190, 13-210 and the washers
13-200, 13-220, 13-230 to the angles 13-090, 13-100, 13-120 and to the
lavatory structure.
TASK 25-41-58-400-814-B01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-002-A01
(1) Installation of the Floor Pan (13A-1)
1 Attach the non-textile flooring 13A-040 with the adhesive tape 13A-045
and the sealant 13A-043 to the floor pan 13A-020.
1 Attach the floor-panel end strip 13A-060 with the screws 13A-070 to the
floor panel assembly 13A-050.
For Myanmar Airways (MMA) use only
(c) Attach the floor panel assembly 13A-050 with the screws 13A-200 to the
lavatory structure.
(d) Attach the angle 13A-140 with the screws 13A-150 and the washers 13A-160
to the floor panel assembly 13A-050.
(e) Attach the angles 13A-110, 13A-120 with the screws 13A-130 to the floor panel
assembly 13A-050.
(f) Attach the angles 13A-170 with the screws 13A-180, the washers 13A-160 and
the nuts 13A-190 to the floor-panel end strip 13A-060.
(g) Attach the floor pan assembly 13A-010 with the screws 13A-210, 13A-230 and
the washers 13A-220, 13A-240, 13A-250 to the angles 13A-110, 13A-120,
13A-140 and to the lavatory structure.
TASK 25-41-58-400-814-C01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-003-A01
(1) Installation of the Floor Pan (13B-1)
1 If removed, attach the non-textile flooring 13B‑44 with the adhesive tape
13B‑30 to the floor pan 13B‑20.
2 Apply the sealant 13B‑45 around the edges of the non-textile flooring
13B‑40 with the seal gun.
1 Attach the floor-panel end strip 13B-060 with the screws 13B-070 to the
floor panel assembly 13B-050.
(c) Attach the floor panel assembly 13B-050 with the screws 13B-200 to the
lavatory structure.
For Myanmar Airways (MMA) use only
(d) Attach the angle 13B-140 with the screws 13B-150 and the washers 13B-160
to the floor panel assembly 13B-050.
(e) Attach the angles 13B-110, 13B-120 with the screws 13B-130 to the floor panel
assembly 13B-050.
(f) Attach the angles 13B-170 with the screws 13B-180, the washers 13B-160 and
the nuts 13B-190 to the floor-panel end strip 13B-060.
(g) Attach floor pan assembly 13B-010 with the screws 13B-210, 13B-230, the
washers 13B-220, 13B-240, 13B-250 to the angles 13B-110, 13B-120, 13B-140
and to the lavatory structure.
TASK 25-41-58-400-814-D01
A. General
For Myanmar Airways (MMA) use only
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-004-A01
(1) Installation of the Floor Pan (13C-1)
1 Attach the floor-panel end strip 13C-060 with the screws 13C-070 to the
floor panel assembly 13C-050.
(b) Attach the floor panel assembly 13C-050 with the screws 13C-200 to the
lavatory structure.
(c) Attach the angle 13C-140 with the screws 13C-150 and the washers 13C-160
to the floor panel assembly 13C-050.
(d) Attach the angles 13C-110, 13C-120 with the screws 13C-130 to the floor
panel assembly 13C-050.
(e) Attach the angles 13C-170 with the screws 13C-180, the washers 13C-160 and
the nuts 13C-190 to the floor-panel end strip 13C-060.
(f) Attach the floor pan assembly 13C-010 with the screws 13C-210, 13C-230 and
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-814-E01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-005-A01
(1) Installation of the Floor Pan (13D-1)
1 Attach the floor-panel end strip 13D-060 with the screws 13D-070 to the
floor panel assembly 13D-050.
(b) Attach the floor panel assembly 13D-050 with the screws 13D-200 to the
lavatory structure.
(c) Attach the angle 13D-140 with the screws 13D-150 and the washers 13D-160
to the floor panel assembly 13D-050.
(d) Attach the angles 13D-110, 13D-120 with the screws 13D-130 to the floor
panel assembly 13D-050.
(e) Attach the angles 13D-170 with the screws 13D-180, the washers 13D-160 and
the nuts 13D-190 to the floor-panel end strip 13D-060.
(f) Attach the floor pan assembly 13D-010 with the screws 13D-210, 13D-230 and
the washers 13D-220, 13D-240, 13D-250 to the angles 13D-110, 13D-120,
13D-140 and to the lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-814-F01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-006-A01
(1) Installation of the Floor Pan (13E-1)
(a) Attach the floor panel assembly 13E-050 with the screws 13E-160 to the
lavatory structure.
(b) Attach the angle 13E-140 with the screws 13E-150 and the washers 13E-100
to the floor panel assembly 13E-050.
(c) Attach the angles 13E-110, 13E-120 with the screws 13E-130 to the floor panel
assembly 13E-050.
1 Attach the non-textile flooring 13E-040 with the adhesive tape 13E-045
and the sealant 13E-043 to the floor pan 13E-020.
(e) Attach the floor pan assembly 13E-010 with the screws 13E-170, 13E-190 and
the washers 13E-180, 13E-200, 13E-210 to the angles 13E-110, 13E-120,
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-814-G01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-007-A01
(1) Installation of the Floor Pan (13F-1)
(a) Attach the non-textile flooring 13F-040 with the adhesive tape 13F-045 and the
sealant 13F-042 to the floor pan 13F-020.
(b) Attach the floor panel assembly 13F-050 with the screws 13F-170 to the
lavatory structure.
(c) Attach the angle 13F-140 with the screws 13F-150 and the washers 13F-100
to the floor panel assembly 13F-050.
(d) Attach the angles 13F-110, 13F-120 with the screws 13F-130 to the floor panel
assembly 13F-050.
(e) Attach the floor pan assembly 13F-010 with the screws 13F-180, 13F-200 and
the washers 13F-190, 13F-210, 13F-220 to the angles 13F-110, 13F-120,
13F-140 and to the lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-814-H01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
For Myanmar Airways (MMA) use only
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-008-A01
(1) Installation of the Floor Pan (13G-1)
(a) Attach the non-textile flooring 13G-040 with the adhesive tape 13G-043 and
the sealant 13G-042 to the floor pan 13G-020.
(b) Attach the floor panel assembly 13G-050 with the screws 13G-170 to the
lavatory structure.
(c) Attach the angle 13G-140 with the screws 13G-150 and the washers 13G-100
to the floor panel assembly 13G-050.
(d) Attach the angles 13G-110, 13G-120 with the screws 13G-130 to the floor
panel assembly 13G-050.
(e) Attach the floor pan assembly 13G-010 with the screws 13G-180, 13G-200 and
the washers 13G-190, 13G-210, 13G-220 to the angles 13G-110, 13G-120,
13G-140 and to the lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-814-J01
A. General
This task gives you the installation and assembly procedures of the component.
For Myanmar Airways (MMA) use only
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-009-A01
(1) Installation of the Floor Pan (13H-1)
(a) Attach the floor panel assembly 13H-050 with the screws 13H-170 to the
lavatory structure.
(b) Attach the angle 13H-130 with the screws 13H-140 and the washers 13H-160
to the floor panel assembly 13H-050.
(c) Attach the angles 13H-100, 13H-110 with the screws 13H-120 to the floor
panel assembly 13H-050.
(d) Attach the floor pan assembly 13H-010 with the screws 13H-180, 13H-200 and
the washers 13H-190, 13H-210, 13H-220 to the angles 13H-100, 13H-110,
13H-130 and to the lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-815-A01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-011-A01
(1) Installation of the Toilet Unit and of the Toilet Shroud (12-1)
(a) Attach the toilet assembly 12-310 with the bolts 12-280, the washers 12-300
and the lock washers 12-290 to the floor pan. Use a max. torque value of
10 N.m (7.376 lbf.ft).
(b) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the toilet assembly 12-310.
(c) Attach the support bracket 12-230 with the screws 12-240 and the washers
12-260 to the lavatory structure.
(d) Attach the support bracket 12-220 with the screws 12-250, the washers 12-260
and the nuts 12-270 to the lavatory structure.
(e) Attach the toilet shroud assembly 12-010 with the screws 12-070 and the nuts
12-080 to the support brackets 12-220, 12-230.
1 Attach the toilet seat assembly 12-170 to the toilet seat assembly 12-090.
3 Attach the toilet cover assembly 12-140 with the fasteners 12-120 to the
toilet seat assembly 12-170.
4 Attach the toilet seat assembly 12-090 with the gaskets 12-110 and the
nuts 12-100 to the toilet shroud assembly 12-010.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-815-B01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
For Myanmar Airways (MMA) use only
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-012-A01
(1) Installation of the Toilet Unit and of the Toilet Shroud (12A-1)
(a) Attach the toilet assembly 12A-330 with the bolts 12A-300, the washers
12A-320 and the lock washers 12A-310 to the floor pan. Use a max. torque
(b) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the toilet assembly 12A-330.
(c) Attach the support bracket 12A-260 with the screws 12A-280, the washers
12A-290 and the nuts 12A-340 to the lavatory structure.
(d) Attach the support bracket 12A-250 with the screws 12A-270 and the washers
12A-290 to the lavatory structure.
For Myanmar Airways (MMA) use only
(e) Attach the toilet shroud assembly 12A-010 with the screws 12A-070 and the
nuts 12A-080 to the support brackets 12A-250, 12A-260.
1 Attach the toilet seat assembly 12A-140 to the toilet seat assembly
12A-090.
2 Attach the toilet cover assembly 12A-100 with the damper assembly
12A-190, 12A-220 to the toilet seat assembly 12A-140.
3 Attach the toilet cover assembly 12A-090 to the toilet shroud assembly
12A-010.
4 Attach the nut 12A-240 and the gasket 12A-230 to the damper assembly
12A-220.
5 Attach the nut 12A-210 and the gasket 12A-200 to the damper assembly
12A-190.
TASK 25-41-58-400-815-C01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-013-A01
(a) Attach the toilet assembly 12B-310 with the bolts 12B-280, the washers
12B-300 and the lock washers 12B-290 to the floor pan. Use a max. torque
value of 10 N.m (7.376 lbf.ft).
(b) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the toilet assembly 12B-310.
(c) Attach the support bracket 12B-230 with the screws 12B-240 and the washers
12B-260 to the lavatory structure.
(d) Attach the support bracket 12B-220 with the screws 12B-250, the washers
12B-260 and the nuts 12B-270 to the lavatory structure.
(e) Attach the toilet shroud assembly 12B-010 with the screws 12B-070 and the
nuts 12B-080 to the support brackets 12B-220, 12B-230.
1 Attach the toilet seat assembly 12B-170 to the toilet seat assembly
12B-090.
3 Attach the toilet cover assembly 12B-140 with the fasteners 12B-120 to
the toilet seat assembly 12B-170.
4 Attach the toilet seat assembly 12B-090 with the gaskets 12B-110 and the
nuts 12B-100 to the toilet shroud assembly 12B-010.
SUBTASK 25-41-58-410-058-A01
(a) Attach the toilet assembly 12B-310 with the bolts 12B-280, the washers
12B-300 and the lock washers 12B-290 to the floor pan. Use a max. torque
value of 10 N.m (7.376 lbf.ft).
(b) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the toilet assembly 12B-310.
(c) Attach the support bracket 12B-230 with the screws 12B-240 and the washers
12B-260 to the lavatory structure.
(d) Attach the support bracket 12B-220 with the screws 12B-250, the washers
12B-260 and the nuts 12B-270 to the lavatory structure.
(e) Attach the toilet shroud assembly 12B-010 with the screws 12B-070 and the
nuts 12B-080 to the support brackets 12B-220, 12B-230.
1 Attach the toilet seat assembly 12B-170 to the toilet seat assembly
12B-090.
3 Attach the toilet cover assembly 12B-140 with the fasteners 12B-120 to
the toilet seat assembly 12B-170.
4 Attach the toilet seat assembly 12B-090 with the gaskets 12B-110 and the
nuts 12B-100 to the toilet shroud assembly 12B-010.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-815-D01
A. General
This task gives you the installation and assembly procedures of the component.
C. Procedure
For Myanmar Airways (MMA) use only
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-014-A01
(1) Installation of the Toilet Unit and of the Toilet Shroud (12C-1)
(a) Attach the toilet assembly 12C-310 with the bolts 12C-280, the washers
12C-300 and the lock washers 12C-290 to the floor pan. Use a max. torque
value of 10 N.m (7.376 lbf.ft).
(b) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the toilet assembly 12C-310.
(c) Attach the support bracket 12C-230 with the screws 12C-240 and the washers
12C-260 to the lavatory structure.
(d) Attach the support bracket 12C-220 with the screws 12C-250, the washers
12C-260 and the nuts 12C-270 to the lavatory structure.
(e) Attach the toilet shroud assembly 12C-010 with the screws 12C-070 and the
nuts 12C-080 to the support brackets 12C-220, 12C-230.
1 Attach the toilet seat assembly 12C-170 to the toilet seat assembly
12C-090.
For Myanmar Airways (MMA) use only
3 Attach the toilet cover assembly 12C-140 with the fasteners 12C-120 to
the toilet seat assembly 12C-170.
4 Attach the toilet seat assembly 12C-090 with the gaskets 12C-110 and
the nuts 12C-100 to the toilet shroud assembly 12C-010.
TASK 25-41-58-400-816-A01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-062-A01
(a) Attach the air outlets 11-170 with the screws 11-180.
For Myanmar Airways (MMA) use only
(b) Attach the latch 11-150 with the screws 11-030 to the single door assembly
11-001.
(d) Attach the lavatory simple door-latch 11-100 with the screws 11-030 to the
single door assembly 11-001.
(e) Attach the sections 11-060, 11-070 with the screws 11-050.
(g) Attach the hinge 11-010 with the screws 11-030 and the washers 11-040.
(i) Attach the coat hook 11-090 with the screw 11-080.
SUBTASK 25-41-58-410-062-B01
(a) Attach the air outlets 11-170 with the screws 11-180.
(b) Attach the latch assembly 11-155 with the screws 11-030 to the single door
assembly 11-001.
(d) Attach the lavatory simple door-latch 11-100 with the screws 11-030 to the
single door assembly 11-001.
(e) Attach the sections 11-060, 11-070 with the screws 11-050.
(g) Attach the hinge 11-010 with the screws 11-030 and the washers 11-040.
(i) Attach the coat hook 11-090 with the screw 11-080.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-816-B01
R225401884-000
60. Assembly of the Door
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-063-A01
(a) Attach the air outlets 11A-170 with the screws 11A-180.
(b) Attach the latch 11A-150 with the screws 11A-030 to the single door assembly
11A-001.
(d) Attach the lavatory simple door-latch 11A-100 with the screws 11A-030 to the
single door assembly 11A-001.
(e) Attach the sections 11A-060, 11A-070 with the screws 11A-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11A-020 and attach the setscrews 11A-020 to the hinge 11A-010.
(g) Attach the hinge 11A-010 with the screws 11A-030 and the washers 11A-040.
(i) Attach the coat hook 11A-090 with the screw 11A-080.
SUBTASK 25-41-58-410-063-B01
(a) Attach the air outlets 11A-170 with the screws 11A-180.
(b) Attach the latch assembly 11A-155 with the screws 11A-030 to the single door
assembly 11A-001.
(d) Attach the lavatory simple door-latch 11A-100 with the screws 11A-030 to the
single door assembly 11A-001.
(e) Attach the lock assy 11A-105 with the screws 11A-030 to the single door
assembly 11A-001.
(f) Attach the sections 11A-060, 11A-070 with the screws 11A-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11A-020 and attach the setscrews 11A-020 to the hinge 11A-010.
(h) Attach the hinge 11A-010 with the screws 11A-030 and the washers 11A-040.
(k) Attach the coat hook 11A-090 with the screw 11A-080.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-816-C01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-064-A01
(a) Attach the air outlets 11B-170 with the screws 11B-180.
(b) Attach the latch assembly 11B-150 with the screws 11B-030 to the single door
assembly 11B-001.
(d) Attach the lavatory simple door-latch 11B-100 with the screws 11B-030 to the
single door assembly 11B-001.
(e) Attach the sections 11B-060, 11B-070 with the screws 11B-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11B-020 and attach the setscrews 11B-020 to the hinge 11B-010.
(g) Attach the hinge 11B-010 with the screws 11B-030 and the washers 11B-040.
(i) Attach the coat hook 11B-090 with the screw 11B-080.
SUBTASK 25-41-58-410-064-B01
(a) Attach the air outlets 11B-170 with the screws 11B-180.
(b) Attach the latch 11B-155 with the screws 11B-030 to the single door assembly
11B-001.
(d) Attach the lavatory simple door-latch 11B-100 with the screws 11B-030 to the
single door assembly 11B-001.
For Myanmar Airways (MMA) use only
(e) Attach the sections 11B-060, 11B-070 with the screws 11B-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11B-020 and attach the setscrews 11B-020 to the hinge 11B-010.
(g) Attach the hinge 11B-010 with the screws 11B-030 and the washers 11B-040.
(i) Attach the coat hook 11B-090 with the screw 11B-080.
TASK 25-41-58-400-816-D01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-065-A01
(1) Assembly of the Door (11C-1)
(a) Attach the air outlets 11C-240 with the screws 11C-230.
(b) Attach the latch assembly 11C-110 with the screws 11C-030 to the single door
assembly 11C-001.
(d) Attach the lavatory simple door-latch 11C-100 with the screws 11C-030 to
the single door assembly 11C-001.
(e) Attach the sections 11C-060, 11C-070 with the screws 11C-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11C-020 and attach the setscrews 11C-020 to the hinge 11C-010.
(g) Attach the hinge 11C-010 with the screws 11C-030 and the washers 11C-040.
(i) Attach the retainers 11C-190 and the end caps 11C-210 with the screws
11C-160 and the washers 11C-170.
(j) Attach the bumpers 11C-200 to the retainers 11C-190 and to the end caps
11C-210.
(k) Attach the coat hook 11C-090 with the screw 11C-080.
TASK 25-41-58-400-816-E01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-066-A01
(a) Attach the air outlets 11D-160 with the screws 11D-170.
(b) Attach the latch 11D-150 with the screws 11D-030 to the single door assembly
11D-001.
(d) Attach the lavatory simple door-latch 11D-100 with the screws 11D-030 to
the single door assembly 11D-001.
For Myanmar Airways (MMA) use only
(e) Attach the sections 11D-060, 11D-070 with the screws 11D-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11D-020 and attach the setscrews 11D-020 to the hinge 11D-010.
(g) Attach the hinge 11D-010 with the screws 11D-030 and the washers 11D-040.
(i) Attach the coat hook 11D-090 with the screw 11D-080.
SUBTASK 25-41-58-410-066-B01
R225401864-000 R225401864-002
(0) Assembly of the Door (11D-1)
(a) Attach the air outlets 11D-160 with the screws 11D-170.
(b) Attach the latch assembly 11D-155 with the screws 11D-030 to the single door
assembly 11D-001.
(d) Attach the lavatory simple door-latch 11D-100 with the screws 11D-030 to
the single door assembly 11D-001.
(e) Attach the sections 11D-060, 11D-070 with the screws 11D-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11D-020 and attach the setscrews 11D-020 to the hinge 11D-010.
(g) Attach the hinge 11D-010 with the screws 11D-030 and the washers 11D-040.
(i) Attach the coat hook 11D-090 with the screw 11D-080.
TASK 25-41-58-400-816-F01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-067-A01
(a) Attach the air outlets 11E-170 with the screws 11E-180.
(b) Attach the latch assembly 11E-155 with the screws 11E-030 to the single door
assembly 11E-001.
(d) Attach the lavatory simple door-latch 11E-100 with the screws 11E-030 to the
single door assembly 11E-001.
simple door-latch).
(e) Attach the sections 11E-060, 11E-070 with the screws 11E-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11E-020 and attach the setscrews 11E-020 to the hinge 11E-010.
(g) Attach the hinge 11E-010 with the screws 11E-030 and the washers 11E-040.
(i) Attach the coat hook 11E-090 with the screw 11E-080.
SUBTASK 25-41-58-410-067-B01
(a) Attach the air outlets 11E-170 with the screws 11E-180.
(b) Attach the latch 11E-150 with the screws 11E-030 to the single door assembly
11E-001.
(d) Attach the lavatory simple door-latch 11E-100 with the screws 11E-030 to the
single door assembly 11E-001.
(e) Attach the sections 11E-060, 11E-070 with the screws 11E-050.
For Myanmar Airways (MMA) use only
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11E-020 and attach the setscrews 11E-020 to the hinge 11E-010.
(g) Attach the hinge 11E-010 with the screws 11E-030 and the washers 11E-040.
(i) Attach the coat hook 11E-090 with the screw 11E-080.
TASK 25-41-58-400-816-G01
A. General
REFERENCE DESIGNATION
For Myanmar Airways (MMA) use only
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-068-A01
(a) Attach the air outlets 11F-170 with the screws 11F-180.
(b) Attach the latch assembly 11F-150 with the screws 11F-030 to the single door
assembly 11F-001.
(d) Attach the lavatory simple door-latch 11F-100 with the screws 11F-030 to the
single door assembly 11F-001.
(e) Attach the sections 11F-060, 11F-070 with the screws 11F-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11F-020 and attach the setscrews 11F-020 to the hinge 11F-010.
(g) Attach the hinge 11F-010 with the screws 11F-030 and the washers 11F-040.
(i) Attach the coat hook 11F-090 with the screw 11F-080.
SUBTASK 25-41-58-410-068-B01
(a) Attach the air outlets 11F-170 with the screws 11F-180.
(b) Attach the latch 11F-155 with the screws 11F-030 to the single door assembly
11F-001.
(d) Attach the lavatory simple door-latch 11F-100 with the screws 11F-030 to the
single door assembly 11F-001.
(e) Attach the sections 11F-060, 11F-070 with the screws 11F-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11F-020 and attach the setscrews 11F-020 to the hinge 11F-010.
(g) Attach the hinge 11F-010 with the screws 11F-030 and the washers 11F-040.
(i) Attach the coat hook 11F-090 with the screw 11F-080.
TASK 25-41-58-400-816-H01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-069-A01
(a) Attach the air outlets 11G-170 with the screws 11G-180.
(b) Attach the latch 11G-155 with the screws 11G-030 to the single door assembly
11G-001.
(d) Attach the lavatory simple door-latch 11G-100 with the screws 11G-030 to
the single door assembly 11G-001.
(e) Attach the sections 11G-060, 11G-070 with the screws 11G-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11G-020 and attach the setscrews 11G-020 to the hinge 11G-010.
(g) Attach the hinge 11G-010 with the screws 11G-030 and the washers 11G-040.
(i) Attach the coat hook 11G-090 with the screw 11G-080.
SUBTASK 25-41-58-410-069-B01
(a) Attach the air outlets 11G-170 with the screws 11G-180.
(b) Attach the latch assembly 11G-150 with the screws 11G-030 to the single
door assembly 11G-001.
(d) Attach the lavatory simple door-latch 11G-100 with the screws 11G-030 to
the single door assembly 11G-001.
(e) Attach the sections 11G-060, 11G-070 with the screws 11G-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11G-020 and attach the setscrews 11G-020 to the hinge 11G-010.
(g) Attach the hinge 11G-010 with the screws 11G-030 and the washers 11G-040.
(i) Attach the coat hook 11G-090 with the screw 11G-080.
TASK 25-41-58-400-816-J01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-070-A01
(a) Attach the air outlets 11H-170 with the screws 11H-180.
(b) Attach the latch assembly 11H-150 with the screws 11H-030 to the single door
assembly 11H-001.
(d) Attach the lavatory simple door-latch 11H-100 with the screws 11H-030 to
the single door assembly 11H-001.
(e) Attach the sections 11H-060, 11H-070 with the screws 11H-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11H-020 and attach the setscrews 11H-020 to the hinge 11H-010.
(g) Attach the hinge 11H-010 with the screws 11H-030 and the washers 11H-040.
(i) Attach the coat hook 11H-090 with the screw 11H-080.
SUBTASK 25-41-58-410-070-B01
(a) Attach the air outlets 11H-170 with the screws 11H-180.
(b) Attach the latch 11H-155 with the screws 11H-030 to the single door assembly
11H-001.
(d) Attach the lavatory simple door-latch 11H-100 with the screws 11H-030 to
the single door assembly 11H-001.
For Myanmar Airways (MMA) use only
(e) Attach the sections 11H-060, 11H-070 with the screws 11H-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11H-020 and attach the setscrews 11H-020 to the hinge 11H-010.
(g) Attach the hinge 11H-010 with the screws 11H-030 and the washers 11H-040.
(i) Attach the coat hook 11H-090 with the screw 11H-080.
TASK 25-41-58-400-816-K01
A. General
REFERENCE DESIGNATION
For Myanmar Airways (MMA) use only
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-071-A01
(a) Attach the air outlets 11J-240 with the screws 11J-230.
(b) Attach the latch 11J-110 with the screws 11J-030 to the single door assembly
11J-001.
(d) Attach the lavatory simple door-latch 11J-100 with the screws 11J-030 to the
single door assembly 11J-001.
(e) Attach the sections 11J-060, 11J-070 with the screws 11J-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11J-020 and attach the setscrews 11J-020 to the hinge 11J-010.
(g) Attach the hinge 11J-010 with the screws 11J-030 and the washers 11J-040.
(i) Attach the retainer 11J-190 and the end caps 11J-210 with the screws 11J-160
and the washers 11J-170.
(j) Attach the bumper 11J-200 to the retainer 11J-190 and to the end caps 11J-210.
(k) Attach the coat hook 11J-090 with the screw 11J-080.
SUBTASK 25-41-58-410-071-B01
(a) Attach the air outlets 11J-240 with the screws 11J-230.
(b) Attach the latch assembly 11J-115 with the screws 11J-030 to the single door
assembly 11J-001.
(d) Attach the lavatory simple door-latch 11J-100 with the screws 11J-030 to the
single door assembly 11J-001.
(e) Attach the sections 11J-060, 11J-070 with the screws 11J-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11J-020 and attach the setscrews 11J-020 to the hinge 11J-010.
(g) Attach the hinge 11J-010 with the screws 11J-030 and the washers 11J-040.
(i) Attach the retainer 11J-190 and the end caps 11J-210 with the screws 11J-160
and the washers 11J-170.
(j) Attach the bumper 11J-200 to the retainer 11J-190 and to the end caps 11J-210.
(k) Attach the coat hook 11J-090 with the screw 11J-080.
TASK 25-41-58-400-816-L01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-072-A01
R225401882-002 R225401895-000
(1) Assembly of the Door (11K-1)
(a) Attach the air outlets 11K-170 with the screws 11K-180.
(b) Attach the latch assembly 11K-150 with the screws 11K-030 to the single door
assembly 11K-001.
(d) Attach the lavatory simple door-latch 11K-100 with the screws 11K-030 to the
single door assembly 11K-001.
(e) Attach the sections 11K-060, 11K-070 with the screws 11K-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11K-020 and attach the setscrews 11K-020 to the hinge 11K-010.
(g) Attach the hinge 11K-010 with the screws 11K-030 and the washers 11K-040.
(i) Attach the coat hook 11K-090 with the screw 11K-080.
SUBTASK 25-41-58-410-072-B01
(a) Attach the air outlets 11K-170 with the screws 11K-180.
(b) Attach the latch 11K-155 with the screws 11K-030 to the single door assembly
11K-001.
(d) Attach the lavatory simple door-latch 11K-100 with the screws 11K-030 to the
single door assembly 11K-001.
(e) Attach the sections 11K-060, 11K-070 with the screws 11K-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11K-020 and attach the setscrews 11K-020 to the hinge 11K-010.
(g) Attach the hinge 11K-010 with the screws 11K-030 and the washers 11K-040.
(i) Attach the coat hook 11K-090 with the screw 11K-080.
TASK 25-41-58-400-816-M01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-073-A01
D2549010413800
(1) Assembly of the Door (11L-1)
(a) Attach the air outlets 11L-170 with the screws 11L-180.
(c) Attach the lavatory simple door-latch 11L-100 with the screws 11L-030 to the
single door assembly 11L-001.
(d) Attach the sections 11L-060, 11L-070 with the screws 11L-050.
MANUFACTURER'S INSTRUCTIONS.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11L-020 and attach the setscrews 11L-020 to the hinge 11L-010.
(f) Attach the hinge 11L-010 with the screws 11L-030 and the washers 11L-040.
(h) Attach the coat hook 11L-090 with the screw 11L-080.
SUBTASK 25-41-58-410-073-B01
(a) Attach the air outlets 11L-170 with the screws 11L-180.
(b) Attach the latch 11L-155 with the screws 11L-030 to the single door assembly
11L-001.
(d) Attach the lavatory simple door-latch 11L-100 with the screws 11L-030 to the
single door assembly 11L-001.
(e) Attach the sections 11L-060, 11L-070 with the screws 11L-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11L-020 and attach the setscrews 11L-020 to the hinge 11L-010.
(g) Attach the hinge 11L-010 with the screws 11L-030 and the washers 11L-040.
(i) Attach the coat hook 11L-090 with the screw 11L-080.
SUBTASK 25-41-58-410-073-C01
(a) Attach the air outlets 11L-170 with the screws 11L-180.
(b) Attach the latch assembly 11L-150 with the screws 11L-030 to the single door
assembly 11L-001.
(d) Attach the lavatory simple door-latch 11L-100 with the screws 11L-030 to the
single door assembly 11L-001.
(e) Attach the lock assy 11L-105 with the screws 11L-030 to the single door
assembly 11L-001.
(f) Attach the sections 11L-060, 11L-070 with the screws 11L-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11L-020 and attach the setscrews 11L-020 to the hinge 11L-010.
(h) Attach the hinge 11L-010 with the screws 11L-030 and the washers 11L-040.
(k) Attach the coat hook 11L-090 with the screw 11L-080.
TASK 25-41-58-400-816-N01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-074-A01
(a) Attach the air outlets 11M-170 with the screws 11M-180.
(b) Attach the latch 11M-150 with the screws 11M-030 to the single door assembly
11M-001.
(d) Attach the lavatory simple door-latch 11M-100 with the screws 11M-030 to
For Myanmar Airways (MMA) use only
(e) Attach the sections 11M-060, 11M-070 with the screws 11M-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11M-020 and attach the setscrews 11M-020 to the hinge 11M-010.
(g) Attach the hinge 11M-010 with the screws 11M-030 and the washers 11M-040.
(i) Attach the coat hook 11M-090 with the screw 11M-080.
SUBTASK 25-41-58-410-074-B01
(a) Attach the air outlets 11M-170 with the screws 11M-180.
(b) Attach the latch assembly 11M-155 with the screws 11M-030 to the single
door assembly 11M-001.
(d) Attach the lavatory simple door-latch 11M-100 with the screws 11M-030 to
the single door assembly 11M-001.
(e) Attach the sections 11M-060, 11M-070 with the screws 11M-050.
For Myanmar Airways (MMA) use only
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11M-020 and attach the setscrews 11M-020 to the hinge 11M-010.
(g) Attach the hinge 11M-010 with the screws 11M-030 and the washers 11M-040.
(i) Attach the coat hook 11M-090 with the screw 11M-080.
TASK 25-41-58-400-816-P01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-075-A01
(a) Attach the air outlets 11N-170 with the screws 11N-180.
(b) Attach the latch assembly 11N-150 with the screws 11N-030 to the single door
assembly 11N-001.
(d) Attach the lavatory simple door-latch 11N-100 with the screws 11N-030 to
the single door assembly 11N-001.
For Myanmar Airways (MMA) use only
(e) Attach the sections 11N-060, 11N-070 with the screws 11N-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11N-020 and attach the setscrews 11N-020 to the hinge 11N-010.
(g) Attach the hinge 11N-010 with the screws 11N-030 and the washers 11N-040.
(i) Attach the coat hook 11N-090 with the screw 11N-080.
SUBTASK 25-41-58-410-075-B01
(a) Attach the air outlets 11N-170 with the screws 11N-180.
(b) Attach the latch 11N-155 with the screws 11N-030 to the single door assembly
11N-001.
(d) Attach the lavatory simple door-latch 11N-100 with the screws 11N-030 to
the single door assembly 11N-001.
(e) Attach the sections 11N-060, 11N-070 with the screws 11N-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11N-020 and attach the setscrews 11N-020 to the hinge 11N-010.
(g) Attach the hinge 11N-010 with the screws 11N-030 and the washers 11N-040.
(i) Attach the coat hook 11N-090 with the screw 11N-080.
TASK 25-41-58-400-816-Q01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-076-A01
(a) Attach the air outlets 11P-170 with the screws 11P-180.
(b) Attach the latch assembly 11P-150 with the screws 11P-030 to the single door
assembly 11P-001.
(d) Attach the lavatory simple door-latch 11P-100 with the screws 11P-030 to the
single door assembly 11P-001.
For Myanmar Airways (MMA) use only
(e) Attach the sections 11P-060, 11P-070 with the screws 11P-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11P-020 and attach the setscrews 11P-020 to the hinge 11P-010.
(g) Attach the hinge 11P-010 with the screws 11P-030 and the washers 11P-040.
(i) Attach the coat hook 11P-090 with the screw 11P-080.
SUBTASK 25-41-58-410-076-B01
(a) Attach the air outlets 11P-170 with the screws 11P-180.
(b) Attach the latch 11P-155 with the screws 11P-030 to the single door assembly
11P-001.
(d) Attach the lavatory simple door-latch 11P-100 with the screws 11P-030 to the
single door assembly 11P-001.
(e) Attach the sections 11P-060, 11P-070 with the screws 11P-050.
For Myanmar Airways (MMA) use only
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11P-020 and attach the setscrews 11P-020 to the hinge 11P-010.
(g) Attach the hinge 11P-010 with the screws 11P-030 and the washers 11P-040.
(i) Attach the coat hook 11P-090 with the screw 11P-080.
TASK 25-41-58-400-816-R01
D2549030811600
74. Assembly of the Door
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-077-A01
(1) Assembly of the Door (11Q-1)
(a) Attach the air outlets 11Q-240 with the screws 11Q-230.
(b) Attach the latch assembly 11Q-110 with the screws 11Q-030 to the single door
assembly 11Q-001.
(d) Attach the lavatory simple door-latch 11Q-100 with the screws 11Q-030 to
the single door assembly 11Q-001.
(e) Attach the sections 11Q-060, 11Q-070 with the screws 11Q-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11Q-020 and attach the setscrews 11Q-020 to the hinge 11Q-010.
(g) Attach the hinge 11Q-010 with the screws 11Q-030 and the washers 11Q-040.
(i) Attach the retainers 11Q-190 and the end caps 11Q-210 with the screws
11Q-160 and the washers 11Q-170.
(j) Attach the bumpers 11Q-200 to the retainers 11Q-190 and to the end caps
11Q-210.
(k) Attach the coat hook 11Q-090 with the screw 11Q-080.
TASK 25-41-58-400-816-S01
A. General
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-078-A01
R225401896-002
(1) Assembly of the Door (11R-1)
(a) Attach the air outlets 11R-170 with the screws 11R-180.
(b) Attach the latch 11R-150 with the screws 11R-030 to the single door assembly
11R-001.
(d) Attach the lavatory simple door-latch 11R-100 with the screws 11R-030 to
the single door assembly 11R-001.
simple door-latch).
(e) Attach the sections 11R-060, 11R-070 with the screws 11R-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11R-020 and attach the setscrews 11R-020 to the hinge 11R-010.
(g) Attach the hinge 11R-010 with the screws 11R-030 and the washers 11R-040.
(i) Attach the coat hook 11R-090 with the screw 11R-080.
SUBTASK 25-41-58-410-078-B01
(a) Attach the air outlets 11R-170 with the screws 11R-180.
(b) Attach the latch assembly 11R-155 with the screws 11R-030 to the single door
assembly 11R-001.
(d) Attach the lavatory simple door-latch 11R-100 with the screws 11R-030 to
the single door assembly 11R-001.
(e) Attach the sections 11R-060, 11R-070 with the screws 11R-050.
1 Apply the Material No. 08-007 Sealant, High Temperature to the setscrews
11R-020 and attach the setscrews 11R-020 to the hinge 11R-010.
(g) Attach the hinge 11R-010 with the screws 11R-030 and the washers 11R-040.
(i) Attach the coat hook 11R-090 with the screw 11R-080.
TASK 25-41-58-400-817-A01
A. General
This task gives you the installation and assembly procedures of the component.
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-015-A01
(1) Installation of the Door (10-1), (11A-1), (11B-1), (11C-1), (11D-1), (11E-1), (11F-1),
(11G-1), (11H-1), (11J-1), (11K-1), (11L-1), (11M-1), (11N-1), (11P-1), (11Q-1),
(11R-1)
(a) Attach the spacer 10-020 and the sill 10-030 with the screws 10-080 to the
floor pan.
(b) Attach the section 10-010 with the screws 10-050 and the nuts 10-070 to the
lavatory structure.
(c) Attach the single door assemblies 11-001, 11A-001, 11B-001, 11C-001,
11D-001, 11E-001, 11F-001, 11G-001, 11H-001, 11J-001, 11K-001, 11L-001,
11M-001, 11N-001, 11P-001, 11Q-001 or 11R-001 and the hinges 11-010,
11A-010, 11B-010, 11C-010, 11D-010, 11E-010, 11F-010, 11G-010, 11H-010,
11J-010, 11K-010, 11L-010, 11M-010, 11N-010, 11P-010, 11Q-010 or 11R-010
with the screws 10-050, the washers 10-060 and the nuts 10-070 to the
lavatory structure.
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-818-A01
A. General
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-017-A01
1 Attach the housing assembly 07-010 with the screws 07-140 and the
washers 07-160 to the lavatory structure.
a Attach the upper fitting 07-165 with the screws 07-130, 07-240 and
the washers 07-150, 07-290 to the housing assembly 07-010.
(b) Attach the decor covers 07-250 with the screws 07-260 to the housing
assembly 07-010.
SUBTASK 25-41-58-410-017-B01
1 Attach the housing assembly 07-010 with the screws 07-140 and the
washers 07-160 to the lavatory structure.
a Attach the upper fitting 07-165 with the screws 07-130, 07-240 and
the washers 07-150, 07-290 to the housing assembly 07-010.
(b) Attach the decor covers 07-250 with the screws 07-260 to the housing
assembly 07-010.
SUBTASK 25-41-58-410-017-C01
1 Attach the housing assembly 07-010 with the screws 07-140 and the
washers 07-160 to the lavatory structure.
a Attach the upper fitting 07-165 with the screws 07-130, 07-240 and
the washers 07-150, 07-290 to the housing assembly 07-010.
(b) Attach the decor covers 07-270, 07-280 with the screws 07-260 to the housing
assembly 07-010.
TASK 25-41-58-400-818-B01
A. General
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-018-A01
1 Attach the housing assembly 07A-010 with the screws 07A-150 and the
washers 07A-170 to the lavatory structure.
a Attach the upper fitting 07A-175 with the screws 07A-140, 07A-250
and the washers 07A-160, 07A-260 to the housing assembly
07A-010.
(b) Attach the decor covers 07A-270, 07A-271 with the screws 07A-280 to the
housing assembly 07A-010.
SUBTASK 25-41-58-410-018-B01
1 Attach the housing assembly 07A-010 with the screws 07A-150 and the
washers 07A-170 to the lavatory structure.
a Attach the upper fitting 07A-175 with the screws 07A-140, 07A-250
and the washers 07A-160, 07A-260 to the housing assembly
07A-010.
(b) Attach the decor covers 07A-270, 07A-275 with the screws 07A-280 to the
housing assembly 07A-010.
SUBTASK 25-41-58-410-018-C01
For Myanmar Airways (MMA) use only
1 Attach the housing assembly 07A-010 with the screws 07A-150 and the
washers 07A-170 to the lavatory structure.
a Attach the upper fitting 07A-175 with the screws 07A-140, 07A-250
and the washers 07A-160, 07A-260 to the housing assembly
07A-010.
(b) Attach the decor covers 07A-270, 07A-271, 07A-275 with the screws 07A-280
to the housing assembly 07A-010.
SUBTASK 25-41-58-410-018-D01
D2549020301200 D2549030707800
1 Attach the housing assembly 07A-010 with the screws 07A-150 and the
washers 07A-170 to the lavatory structure.
a Attach the upper fitting 07A-175 with the screws 07A-140, 07A-250
and the washers 07A-160, 07A-260 to the housing assembly
07A-010.
(b) Attach the decor covers 07A-270, 07A-271 with the screws 07A-280 to the
For Myanmar Airways (MMA) use only
(c) Attach the cosmetics holder 07A-320 and the spacer 07A-330 with the screws
07A-340 to the housing assembly 07A-010.
(d) Attach the soap dispenser holder 07A-290 with the screws 07A-300 and the
washers 07A-310 to the housing assembly 07A-010.
TASK 25-41-58-400-818-C01
A. General
For Myanmar Airways (MMA) use only
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-019-A01
1 Attach the housing assembly 07B-010 with the screws 07B-150 and the
washers 07B-170 to the lavatory structure.
a Attach the upper fitting 07B-175 with the screws 07B-140, 07B-250
and the washers 07B-160, 07B-260 to the housing assembly
07B-010.
(b) Attach the decor covers 07B-300 with the screws 07B-290 to the housing
assembly 07B-010.
SUBTASK 25-41-58-410-019-B01
1 Attach the housing assembly 07B-010 with the screws 07B-150 and the
washers 07B-170 to the lavatory structure.
a Attach the upper fitting 07B-175 with the screws 07B-140, 07B-250
and the washers 07B-160, 07B-260 to the housing assembly
07B-010.
(b) Attach the decor covers 07B-270, 07B-280 with the screws 07B-290 to the
housing assembly 07B-010.
TASK 25-41-58-400-818-D01
A. General
B. Procedure
For Myanmar Airways (MMA) use only
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-020-A01
1 Attach the housing assembly 07C-010 with the screws 07C-150 and the
washers 07C-170 to the lavatory structure.
a Attach the upper fitting 07C-175 with the screws 07C-140, 07C-250
and the washers 07C-160, 07C-260 to the housing assembly
07C-010.
(b) Attach the decor covers 07C-280 with the screws 07C-270 to the housing
assembly 07C-010.
SUBTASK 25-41-58-410-020-B01
1 Attach the housing assembly 07C-010 with the screws 07C-150 and the
washers 07C-170 to the lavatory structure.
a Attach the upper fitting 07C-175 with the screws 07C-140, 07C-250
and the washers 07C-160, 07C-260 to the housing assembly
07C-010.
(b) Attach the decor covers 07C-290, 07C-300 with the screws 07C-270 to the
housing assembly 07C-010.
SUBTASK 25-41-58-410-020-C01
D2549020305200 D2549030712000
(0) Installation of the Housing (07C-1)
1 Attach the housing assembly 07C-010 with the screws 07C-150 and the
washers 07C-170 to the lavatory structure.
a Attach the upper fitting 07C-175 with the screws 07C-140, 07C-250
and the washers 07C-160, 07C-260 to the housing assembly
07C-010.
(b) Attach the decor covers 07C-280 with the screws 07C-270 to the housing
assembly 07C-010.
(c) Attach the vase 07C-310 with the screws 07C-320 to the housing assembly
07C-010.
TASK 25-41-58-400-818-E01
A. General
B. Procedure
For Myanmar Airways (MMA) use only
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-021-A01
1 Attach the housing assembly 07D-010 with the screws 07D-150 and the
washers 07D-170 to the lavatory structure.
a Attach the upper fitting 07D-175 with the screws 07D-140, 07D-250
and the washers 07D-160, 07D-260 to the housing assembly
07D-010.
(b) Attach the decor covers 07D-270, 07D-280 with the screws 07D-290 to the
housing assembly 07D-010.
SUBTASK 25-41-58-410-021-B01
1 Attach the housing assembly 07D-010 with the screws 07D-150 and the
washers 07D-170 to the lavatory structure.
a Attach the upper fitting 07D-175 with the screws 07D-140, 07D-250
and the washers 07D-160, 07D-260 to the housing assembly
07D-010.
(b) Attach the decor covers 07D-270, 07D-271 with the screws 07D-290 to the
housing assembly 07D-010.
SUBTASK 25-41-58-410-021-C01
1 Attach the housing assembly 07D-010 with the screws 07D-150 and the
washers 07D-170 to the lavatory structure.
a Attach the upper fitting 07D-175 with the screws 07D-140, 07D-250
and the washers 07D-160, 07D-260 to the housing assembly
07D-010.
(b) Attach the decor covers 07D-270, 07D-271 with the screws 07D-290 to the
housing assembly 07D-010.
SUBTASK 25-41-58-410-021-D01
D2549020308400
(0) Installation of the Housing (07D-1)
1 Attach the housing assembly 07D-010 with the screws 07D-150 and the
washers 07D-170 to the lavatory structure.
a Attach the upper fitting 07D-175 with the screws 07D-140, 07D-250
and the washers 07D-160, 07D-260 to the housing assembly
07D-010.
(b) Attach the decor covers 07D-270, 07D-280 with the screws 07D-290 to the
housing assembly 07D-010.
(c) Attach the vase 07D-300 with the screws 07D-310 to the housing assembly
07D-010.
TASK 25-41-58-400-818-F01
A. General
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-022-A01
1 Attach the housing assembly 07E-010 with the screws 07E-150 and the
washers 07E-170 to the lavatory structure.
a Attach the upper fitting 07E-175 with the screws 07E-140, 07E-250
and the washers 07E-160, 07E-260 to the housing assembly
07E-010.
(b) Attach the decor covers 07E-270, 07E-280 with the screws 07E-290 to the
housing assembly 07E-010.
SUBTASK 25-41-58-410-022-B01
D2549020900400 R225401869-000
(0) Installation of the Housing (07E-1)
1 Attach the housing assembly 07E-010 with the screws 07E-150 and the
washers 07E-170 to the lavatory structure.
a Attach the upper fitting 07E-175 with the screws 07E-140, 07E-250
and the washers 07E-160, 07E-260 to the housing assembly
07E-010.
(b) Attach the decor covers 07E-270, 07E-280 with the screws 07E-290 to the
housing assembly 07E-010.
(c) Attach the perfume holder 07E-300 with the screws 07E-310 to the housing
assembly 07E-010.
SUBTASK 25-41-58-410-022-C01
D2549010410400
(0) Installation of the Housing (07E-1)
1 Attach the housing assembly 07E-010 with the screws 07E-150 and the
washers 07E-170 to the lavatory structure.
a Attach the upper fitting 07E-175 with the screws 07E-140, 07E-250
and the washers 07E-160, 07E-260 to the housing assembly
07E-010.
(b) Attach the decor covers 07E-270, 07E-280 with the screws 07E-290 to the
housing assembly 07E-010.
(c) Attach the cosmetics holder 07E-300 with the screws 07E-330 and the washers
07E-340 to the housing assembly 07E-010.
(d) Attach the vase 07E-320 with the screws 07E-310 to the housing assembly
07E-010.
TASK 25-41-58-400-818-G01
R225401888-008 R225401888-012
83. Installation of the Housing
A. General
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-023-A01
1 Attach the housing assembly 07F-010 with the screws 07F-150 and the
washers 07F-170 to the lavatory structure.
For Myanmar Airways (MMA) use only
a Attach the upper fitting 07F-175 with the screws 07F-140, 07F-250
and the washers 07F-160, 07F-260 to the housing assembly
07F-010.
(b) Attach the decor covers 07F-270 with the screws 07F-280 to the housing
assembly 07F-010.
SUBTASK 25-41-58-410-023-B01
1 Attach the housing assembly 07F-010 with the screws 07F-150 and the
washers 07F-170 to the lavatory structure.
a Attach the upper fitting 07F-175 with the screws 07F-140, 07F-250
and the washers 07F-160, 07F-260 to the housing assembly
07F-010.
(b) Attach the decor covers 07F-270 with the screws 07F-280 to the housing
assembly 07F-010.
SUBTASK 25-41-58-410-023-C01
For Myanmar Airways (MMA) use only
1 Attach the housing assembly 07F-010 with the screws 07F-150 and the
washers 07F-170 to the lavatory structure.
a Attach the upper fitting 07F-175 with the screws 07F-140, 07F-250
and the washers 07F-160, 07F-260 to the housing assembly
07F-010.
(b) Attach the decor covers 07F-271, 07F-320 with the screws 07F-280 to the
housing assembly 07F-010.
SUBTASK 25-41-58-410-023-D01
D2549010411000
(0) Installation of the Housing (07F-1)
1 Attach the housing assembly 07F-010 with the screws 07F-150 and the
washers 07F-170 to the lavatory structure.
a Attach the upper fitting 07F-175 with the screws 07F-140, 07F-250
and the washers 07F-160, 07F-260 to the housing assembly
07F-010.
For Myanmar Airways (MMA) use only
(b) Attach the decor covers 07F-270 with the screws 07F-280 to the housing
assembly 07F-010.
(c) Attach the perfume holder 07F-290 with the screws 07F-300 to the housing
assembly 07F-010.
(d) Attach the vase 07F-310 with the screws 07F-300 to the housing assembly
07F-010.
SUBTASK 25-41-58-410-023-E01
D2549020905200 D2549030807200
(0) Installation of the Housing (07F-1)
1 Attach the housing assembly 07F-010 with the screws 07F-150 and the
washers 07F-170 to the lavatory structure.
a Attach the upper fitting 07F-175 with the screws 07F-140, 07F-250
and the washers 07F-160, 07F-260 to the housing assembly
07F-010.
(b) Attach the decor covers 07F-271, 07F-320 with the screws 07F-280 to the
housing assembly 07F-010.
(c) Attach the vase 07F-310 with the screws 07F-301 to the housing assembly
07F-010.
TASK 25-41-58-400-818-H01
A. General
For Myanmar Airways (MMA) use only
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-024-A01
(1) Installation of the Housing (07G-1)
(a) Install the mirror 07G-184, the mirror door panel 07G-186 and the adhesive film
to the mirror assy 07G-182.
(b) Install the mirror assy 07G-182 with the screws 07G-200.
1 Attach the housing assembly 07G-010 with the screws 07G-150 and the
washers 07G-170 to the lavatory structure.
a Attach the upper fitting 07G-175 with the screws 07G-140, 07G-250
and the washers 07G-160, 07G-260 to the housing assembly
07G-010.
(d) Attach the decor covers 07G-270, 07G-290 with the screws 07G-280 to the
For Myanmar Airways (MMA) use only
TASK 25-41-58-400-818-J01
A. General
B. Procedure
For Myanmar Airways (MMA) use only
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-025-A01
1 Attach the housing assembly 07H-010 with the screws 07H-150 and the
washers 07H-170 to the lavatory structure.
a Attach the upper fitting 07H-175 with the screws 07H-140, 07H-250
and the washers 07H-160, 07H-260 to the housing assembly
07H-010.
(b) Attach the decor covers 07H-270, 07H-275 with the screws 07H-280 to the
housing assembly 07H-010.
SUBTASK 25-41-58-410-025-B01
D2549020908000 D2549020911200
(0) Installation of the Housing (07H-1)
1 Attach the housing assembly 07H-010 with the screws 07H-150 and the
washers 07H-170 to the lavatory structure.
a Attach the upper fitting 07H-175 with the screws 07H-140, 07H-250
and the washers 07H-160, 07H-260 to the housing assembly
07H-010.
(b) Attach the decor covers 07H-270, 07H-275 with the screws 07H-280 to the
housing assembly 07H-010.
SUBTASK 25-41-58-410-025-C01
D2549030807800
(0) Installation of the Housing (07H-1)
1 Attach the housing assembly 07H-010 with the screws 07H-150 and the
washers 07H-170 to the lavatory structure.
a Attach the upper fitting 07H-175 with the screws 07H-140, 07H-250
and the washers 07H-160, 07H-260 to the housing assembly
For Myanmar Airways (MMA) use only
07H-010.
(b) Attach the decor covers 07H-270, 07H-275 with the screws 07H-280 to the
housing assembly 07H-010.
(c) Attach the soap dispenser holder 07H-290 with the screws 07H-300 and the
washers 07H-310 to the housing assembly 07H-010.
(d) Attach the cosmetics holder 07H-320 and the spacer 07H-330 with the screws
07H-340 to the housing assembly 07H-010.
TASK 25-41-58-400-818-K01
A. General
B. Procedure
For Myanmar Airways (MMA) use only
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-026-A01
1 Attach the housing assembly 07J-010 with the screws 07J-150 and the
washers 07J-170 to the lavatory structure.
a Attach the upper fitting 07J-175 with the screws 07J-140, 07J-250
and the washers 07J-160, 07J-260 to the housing assembly 07J-010.
(b) Attach the decor covers 07J-270, 07J-271 with the screws 07J-280 to the
housing assembly 07J-010.
SUBTASK 25-41-58-410-026-B01
1 Attach the housing assembly 07J-010 with the screws 07J-150 and the
washers 07J-170 to the lavatory structure.
a Attach the upper fitting 07J-175 with the screws 07J-140, 07J-250
and the washers 07J-160, 07J-260 to the housing assembly 07J-010.
(b) Attach the decor covers 07J-270, 07J-290 with the screws 07J-280 to the
housing assembly 07J-010.
SUBTASK 25-41-58-410-026-C01
D2549010413800
(0) Installation of the Housing (07J-1)
1 Attach the housing assembly 07J-010 with the screws 07J-150 and the
washers 07J-170 to the lavatory structure.
a Attach the upper fitting 07J-175 with the screws 07J-140, 07J-250
and the washers 07J-160, 07J-260 to the housing assembly 07J-010.
For Myanmar Airways (MMA) use only
(b) Attach the perfume holder 07J-310 with the screws 07J-320 to the housing
assembly 07J-010.
(c) Attach the vase 07J-300 with the screws 07J-320 to the housing assembly
07J-010.
(d) Attach the decor covers 07J-270, 07J-271 with the screws 07J-280 to the
housing assembly 07J-010.
TASK 25-41-58-400-818-L01
A. General
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-027-A01
1 Attach the housing assembly 07K-010 with the screws 07K-150 and the
washers 07K-170 to the lavatory structure.
a Attach the upper fitting 07K-220 with the screws 07K-140, 07K-310
and the washers 07K-160, 07K-320 to the housing assembly
07K-010.
(b) Attach the decor covers 07K-330, 07K-331 with the screws 07K-340 to the
housing assembly 07K-010.
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-410-027-B01
D2549030810200
(0) Installation of the Housing (07K-1)
1 Attach the housing assembly 07K-010 with the screws 07K-150 and the
washers 07K-170 to the lavatory structure.
a Attach the upper fitting 07K-220 with the screws 07K-140, 07K-310
and the washers 07K-160, 07K-320 to the housing assembly
07K-010.
(b) Attach the decor covers 07K-330, 07K-331 with the screws 07K-340 to the
housing assembly 07K-010.
SUBTASK 25-41-58-410-027-C01
D2549010414600
(0) Installation of the Housing (07K-1)
1 Attach the housing assembly 07K-010 with the screws 07K-150 and the
washers 07K-170 to the lavatory structure.
a Attach the upper fitting 07K-220 with the screws 07K-140, 07K-310
and the washers 07K-160, 07K-320 to the housing assembly
07K-010.
(b) Attach the decor covers 07K-330, 07K-331 with the screws 07K-340 to the
housing assembly 07K-010.
(c) Attach the cosmetics holder 07K-350 with the screws 07K-360 and the washers
07K-390 to the housing assembly 07K-010.
SUBTASK 25-41-58-410-027-D01
1 Attach the housing assembly 07K-010 with the screws 07K-150 and the
washers 07K-170 to the lavatory structure.
a Attach the upper fitting 07K-220 with the screws 07K-140, 07K-310
and the washers 07K-160, 07K-320 to the housing assembly
07K-010.
(b) Attach the decor covers 07K-330, 07K-331 with the screws 07K-340 to the
housing assembly 07K-010.
(c) Attach the cosmetics holder 07K-350 with the screws 07K-360 and the washers
07K-390 to the housing assembly 07K-010.
For Myanmar Airways (MMA) use only
(d) Attach the vase 07K-370 with the screws 07K-380 to the housing assembly
07K-010.
TASK 25-41-58-400-818-M01
A. General
B. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-028-A01
D2549010301000
(1) Installation of the Housing (07L-1)
1 Attach the housing assembly 07L-010 with the screws 07L-150 and the
washers 07L-170 to the lavatory structure.
a Attach the upper fitting 07L-220 with the screws 07L-140, 07L-310
and the washers 07L-160, 07L-320 to the housing assembly
07L-010.
(b) Attach the perfume holder 07L-360 with the screws 07L-370 to the housing
assembly 07L-010.
(c) Attach the decor covers 07L-330, 07L-340 with the screws 07L-350 to the
housing assembly 07L-010.
SUBTASK 25-41-58-410-028-B01
D2549010300800
(0) Installation of the Housing (07L-1)
1 Attach the housing assembly 07L-010 with the screws 07L-150 and the
washers 07L-170 to the lavatory structure.
a Attach the upper fitting 07L-220 with the screws 07L-140, 07L-310
and the washers 07L-160, 07L-320 to the housing assembly
07L-010.
(b) Attach the perfume holder 07L-360 with the screws 07L-370 to the housing
assembly 07L-010.
(c) Attach the decor covers 07L-330, 07L-340 with the screws 07L-350 to the
housing assembly 07L-010.
SUBTASK 25-41-58-410-028-C01
1 Attach the housing assembly 07L-010 with the screws 07L-150 and the
washers 07L-170 to the lavatory structure.
a Attach the upper fitting 07L-220 with the screws 07L-140, 07L-310
and the washers 07L-160, 07L-320 to the housing assembly
07L-010.
For Myanmar Airways (MMA) use only
(b) Attach the decor covers 07L-330, 07L-340 with the screws 07L-350 to the
housing assembly 07L-010.
TASK 25-41-58-400-819-A01
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-029-A01
(a) Attach the fittings 06-020, 06-030 with the screws 06-040, 06-050.
(b) Attach the toilet seat-cover dispenser 06-430 with the screws 06-440 to the aft
side wall assembly 06-010.
1 Attach the plates 06-255 with the screws 06-240 to the post assembly
06-230.
(d) Attach the post assembly 06-230 with the screws 06-260, 06-280, the washers
06-210 and the caps 06-270.
(e) Assemble the single door emergency unlocking device assembly 06-350 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06-400 and to the pin 06-390 and attach the emergency unlocking
device pivot 06-380, the snap catch 06-400 and the pin 06-390 to the
emergency unlocking device housing 06-360.
NOTE: Adjust the snap catch 06-400 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06-410 and attach the emergency unlocking device strike 06-370 with the
bolt 06-410 to the emergency unlocking device housing 06-360.
(f) Attach the single door emergency unlocking device assembly 06-350 with the
screws 06-420 to the post assembly 06-230.
(g) Attach the angle 06-340 with the screws 06-260 and the washers 06-210 to the
aft side wall assembly 06-010.
(h) Attach the angles 06-180 with the screws 06-200 and the washers 06-210
to the aft side wall assembly 06-010.
For Myanmar Airways (MMA) use only
(j) Attach the oxygen container assy 06-190 with the screws 06-200, 06-205 and
the washers 06-210, 06-215 to the angles 06-180.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06-190.
(l) Attach the angle 06-150 with the screws 06-200 and the washers 06-210 to the
aft side wall assembly 06-010.
(m) Attach the oxygen container assy cover 06-140 with the screws 06-160 and
the nuts 06-170 to the angle 06-150.
(n) Attach the studs 06-220 and the washers 06-210 to the oxygen container assy
cover 06-140.
(p) Attach the support 06-330 with the screws 06-260 and the washers 06-210
to the aft side wall assembly 06-010.
1 Attach the special screws 06-300 and the special washers 06-320 to the
aft side wall assembly 06-010.
2 Attach the handle assembly 06-290 to the aft side wall assembly 06-010.
SUBTASK 25-41-58-410-029-B01
D2549020305200
(0) Installation of the Side Wall (06-1)
(a) Attach the fittings 06-020, 06-030 with the screws 06-040, 06-050.
(b) Attach the toilet seat-cover dispenser 06-430 with the screws 06-440 to the aft
side wall assembly 06-010.
1 Attach the plates 06-255 with the screws 06-240 to the post assembly
06-230.
(d) Attach the post assembly 06-230 with the screws 06-260, 06-280, the washers
For Myanmar Airways (MMA) use only
(e) Assemble the single door emergency unlocking device assembly 06-350 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06-400 and to the pin 06-390 and attach the emergency unlocking
device pivot 06-380, the snap catch 06-400 and the pin 06-390 to the
emergency unlocking device housing 06-360.
NOTE: Adjust the snap catch 06-400 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06-410 and attach the emergency unlocking device strike 06-370 with the
bolt 06-410 to the emergency unlocking device housing 06-360.
(f) Attach the single door emergency unlocking device assembly 06-350 with the
screws 06-420 to the post assembly 06-230.
(g) Attach the angle 06-340 with the screws 06-260 and the washers 06-210 to the
aft side wall assembly 06-010.
(h) Attach the angles 06-180 with the screws 06-200 and the washers 06-210
to the aft side wall assembly 06-010.
(j) Attach the oxygen container assy 06-190 with the screws 06-200 and the
washers 06-210 to the angles 06-180.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06-190.
(l) Attach the angle 06-150 with the screws 06-200 and the washers 06-210 to the
aft side wall assembly 06-010.
(m) Attach the oxygen container assy cover 06-140 with the screws 06-160 and
the nuts 06-170 to the angle 06-150.
(n) Attach the studs 06-220 and the washers 06-210 to the oxygen container assy
For Myanmar Airways (MMA) use only
cover 06-140.
1 Attach the special screws 06-300 and the special washers 06-320 to the
aft side wall assembly 06-010.
2 Attach the handle assembly 06-290 to the aft side wall assembly 06-010.
SUBTASK 25-41-58-410-029-C01
(a) Attach the fittings 06-020, 06-030 with the screws 06-040, 06-050.
1 Attach the plates 06-255 with the screws 06-240 to the post assembly
06-230.
(c) Attach the post assembly 06-230 with the screws 06-260, 06-280, the washers
06-210 and the caps 06-270.
(d) Assemble the single door emergency unlocking device assembly 06-350 as
follows:
NOTE: Adjust the snap catch 06-400 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
For Myanmar Airways (MMA) use only
06-410 and attach the emergency unlocking-device strike 06-370 with the
bolt 06-410 to the emergency unlocking-device housing 06-360.
(e) Attach the single door emergency unlocking device assembly 06-350 with the
screws 06-420 to the post assembly 06-230.
(f) Attach the angle 06-340 with the screws 06-260 and the washers 06-210 to the
aft side wall assembly 06-010.
(g) Attach the angles 06-180 with the screws 06-200 and the washers 06-210
to the aft side wall assembly 06-010.
(h) Attach the oxygen container assy 06-190 with the screws 06-200 and the
washers 06-210 to the angles 06-180.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06-190.
(k) Attach the angle 06-150 with the screws 06-200 and the washers 06-210 to the
aft side wall assembly 06-010.
(l) Attach the oxygen container assy cover 06-140 with the screws 06-160 and
the nuts 06-170 to the angle 06-150.
(m) Attach the studs 06-220 and the washers 06-210 to the oxygen container assy
cover 06-140.
(n) Attach the support 06-330 with the screws 06-260 and the washers 06-210
to the aft side wall assembly 06-010.
1 Attach the special screws 06-300 and the special washers 06-320 to the
aft side wall assembly 06-010.
2 Attach the handle assembly 06-290 to the aft side wall assembly 06-010.
SUBTASK 25-41-58-410-029-D01
(a) Attach the fittings 06-020, 06-030 with the screws 06-040, 06-050.
For Myanmar Airways (MMA) use only
(b) Attach the toilet seat-cover dispenser 06-430 with the screws 06-440 to the aft
side wall assembly 06-010.
1 Attach the plates 06-255 with the screws 06-240 to the post assembly
06-230.
(d) Attach the post assembly 06-230 with the screws 06-260, 06-280, the washers
06-210 and the caps 06-270.
(e) Assemble the single door emergency unlocking device assembly 06-350 as
follows:
NOTE: Adjust the snap catch 06-400 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06-410 and attach the emergency unlocking-device strike 06-370 with the
bolt 06-410 to the emergency unlocking-device housing 06-360.
(f) Attach the single door emergency unlocking device assembly 06-350 with the
screws 06-420 to the post assembly 06-230.
(g) Attach the angle 06-340 with the screws 06-260 and the washers 06-210 to the
aft side wall assembly 06-010.
(h) Attach the angles 06-180 with the screws 06-200 and the washers 06-210
to the aft side wall assembly 06-010.
(j) Attach the oxygen container assy 06-190 with the screws 06-200, 06-205 and
the washers 06-210 to the angles 06-180.
For Myanmar Airways (MMA) use only
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06-190.
(l) Attach the angle 06-150 with the screws 06-200 and the washers 06-210 to the
aft side wall assembly 06-010.
(m) Attach the oxygen container assy cover 06-140 with the screws 06-160 and
the nuts 06-170 to the angle 06-150.
(n) Attach the studs 06-220 and the washers 06-210 to the oxygen container assy
cover 06-140.
(p) Attach the support 06-330 with the screws 06-260 and the washers 06-210
to the aft side wall assembly 06-010.
1 Attach the special screws 06-300 and the special washers 06-320 to the
aft side wall assembly 06-010.
2 Attach the handle assembly 06-290 to the aft side wall assembly 06-010.
TASK 25-41-58-400-819-B01
A. General
This task gives you the installation and assembly procedures of the component.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-030-A01
For Myanmar Airways (MMA) use only
(a) Attach the fittings 06A-020, 06A-030 with the screws 06A-040, 06A-050.
1 Attach the plates 06A-295 with the screws 06A-280 to the post assembly
06A-270.
(c) Attach the post assembly 06A-270 with the screws 06A-300, 06A-320, the
washers 06A-250 and the caps 06A-310.
(d) Assemble the single door emergency unlocking device assembly 06A-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06A-420 and to the pin 06A-410 and attach the emergency
unlocking device pivot 06A-400, the snap catch 06A-420 and the pin
06A-410 to the emergency unlocking device housing 06A-380.
NOTE: Adjust the snap catch 06A-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06A-430 and attach the emergency unlocking device strike 06A-390 with
the bolt 06A-430 to the emergency unlocking device housing 06A-380.
(e) Attach the single door emergency unlocking device assembly 06A-370 with the
screws 06A-360 to the post assembly 06A-270.
(f) Attach the angle 06A-350 with the screws 06A-300 and the washers 06A-250
to the aft side wall assembly 06A-010.
(g) Attach the angles 06A-220 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
For Myanmar Airways (MMA) use only
(h) Attach the oxygen container assy 06A-230 with the screws 06A-240 and the
washers 06A-250 to the angles 06A-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06A-230.
(k) Attach the angle 06A-190 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(l) Attach the oxygen container assy cover 06A-180 with the screws 06A-200 and
the nuts 06A-210 to the angle 06A-190.
(m) Attach the studs 06A-260 and the washers 06A-250 to the oxygen container
assy cover 06A-180.
1 Attach the special screws 06A-150 and the special washers 06A-170 to
the aft side wall assembly 06A-010.
2 Attach the handle assemblies 06A-140 to the aft side wall assembly
06A-010.
SUBTASK 25-41-58-410-030-B01
(a) Attach the fittings 06A-020, 06A-030 with the screws 06A-040, 06A-050.
1 Attach the plates 06A-295 with the screws 06A-280 to the post assembly
06A-270.
(c) Attach the post assembly 06A-270 with the screws 06A-300, 06A-320, the
washers 06A-250 and the caps 06A-310.
(d) Assemble the single door emergency unlocking device assembly 06A-370 as
follows:
For Myanmar Airways (MMA) use only
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06A-420 and to the pin 06A-410 and attach the emergency
unlocking device pivot 06A-400, the snap catch 06A-420 and the pin
06A-410 to the emergency unlocking device housing 06A-380.
NOTE: Adjust the snap catch 06A-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06A-430 and attach the emergency unlocking device strike 06A-390 with
the bolt 06A-430 to the emergency unlocking device housing 06A-380.
(e) Attach the single door emergency unlocking device assembly 06A-370 with the
screws 06A-360 to the post assembly 06A-270.
(f) Attach the angle 06A-350 with the screws 06A-300 and the washers 06A-250
to the aft side wall assembly 06A-010.
(g) Attach the angles 06A-220 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(h) Attach the oxygen container assy 06A-230 with the screws 06A-240, 06A-245
and the washers 06A-250 to the angles 06A-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06A-230.
(k) Attach the angle 06A-190 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(l) Attach the oxygen container assy cover 06A-180 with the screws 06A-200 and
the nuts 06A-210 to the angle 06A-190.
(m) Attach the studs 06A-260 and the washers 06A-250 to the oxygen container
assy cover 06A-180.
1 Attach the special screws 06A-150 and the special washers 06A-170 to
the aft side wall assembly 06A-010.
2 Attach the handle assemblies 06A-140 to the aft side wall assembly
06A-010.
SUBTASK 25-41-58-410-030-C01
D2549020301400
(0) Installation of the Side Wall (06A-1)
(a) Attach the fittings 06A-020, 06A-030 with the screws 06A-040, 06A-050.
1 Attach the plates 06A-295 with the screws 06A-280 to the post assembly
06A-270.
(c) Attach the post assembly 06A-270 with the screws 06A-300, 06A-320, the
washers 06A-250 and the caps 06A-310.
(d) Assemble the single door emergency unlocking device assembly 06A-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06A-420 and to the pin 06A-410 and attach the emergency
unlocking device pivot 06A-400, the snap catch 06A-420 and the pin
06A-410 to the emergency unlocking device housing 06A-380.
NOTE: Adjust the snap catch 06A-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
For Myanmar Airways (MMA) use only
06A-430 and attach the emergency unlocking device strike 06A-390 with
the bolt 06A-430 to the emergency unlocking device housing 06A-380.
(e) Attach the single door emergency unlocking device assembly 06A-370 with the
screws 06A-360 to the post assembly 06A-270.
(f) Attach the angle 06A-350 with the screws 06A-300 and the washers 06A-250
to the aft side wall assembly 06A-010.
(g) Attach the angles 06A-220 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(h) Attach the oxygen container assy 06A-230 with the screws 06A-240 and the
washers 06A-250 to the angles 06A-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06A-230.
(k) Attach the angle 06A-190 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(l) Attach the oxygen container assy cover 06A-180 with the screws 06A-200 and
the nuts 06A-210 to the angle 06A-190.
(m) Attach the studs 06A-260 and the washers 06A-250 to the oxygen container
assy cover 06A-180.
1 Attach the special screws 06A-150 and the special washers 06A-170 to
the aft side wall assembly 06A-010.
2 Attach the handle assemblies 06A-140 to the aft side wall assembly
06A-010.
SUBTASK 25-41-58-410-030-D01
(a) Attach the fittings 06A-020, 06A-030 with the screws 06A-040, 06A-050.
For Myanmar Airways (MMA) use only
1 Attach the plates 06A-295 with the screws 06A-280 to the post assembly
06A-270.
(c) Attach the post assembly 06A-270 with the screws 06A-300, 06A-320, the
washers 06A-250 and the caps 06A-310.
(d) Assemble the single door emergency unlocking device assembly 06A-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06A-420 and to the pin 06A-410 and attach the emergency
unlocking device pivot 06A-400, the snap catch 06A-420 and the pin
06A-410 to the emergency unlocking device housing 06A-380.
NOTE: Adjust the snap catch 06A-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06A-430 and attach the emergency unlocking device strike 06A-390 with
the bolt 06A-430 to the emergency unlocking device housing 06A-380.
(e) Attach the single door emergency unlocking device assembly 06A-370 with the
screws 06A-360 to the post assembly 06A-270.
(f) Attach the angle 06A-350 with the screws 06A-300 and the washers 06A-250
to the aft side wall assembly 06A-010.
(g) Attach the angles 06A-220 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(h) Attach the oxygen container assy 06A-230 with the screws 06A-240 and the
washers 06A-250 to the angles 06A-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06A-230.
(k) Attach the angle 06A-190 with the screws 06A-240 and the washers 06A-250
For Myanmar Airways (MMA) use only
(l) Attach the oxygen container assy cover 06A-180 with the screws 06A-200 and
the nuts 06A-210 to the angle 06A-190.
(m) Attach the studs 06A-260 and the washers 06A-250 to the oxygen container
assy cover 06A-180.
1 Attach the screws 06A-460 and the washers 06A-470 to the aft side wall
assembly 06A-010.
2 Attach the handle 06A-450 to the screws 06A-460 and hold with the
setscrews 06A-480.
SUBTASK 25-41-58-410-030-E01
(a) Attach the fittings 06A-020, 06A-030 with the screws 06A-040, 06A-050.
(b) Attach the toilet seat-cover dispenser 06A-330 with the screws 06A-340 to
the aft side wall assembly 06A-010.
1 Attach the plates 06A-295 with the screws 06A-280 to the post assembly
06A-270.
(d) Attach the post assembly 06A-270 with the screws 06A-300, 06A-305,
06A-320, the washers 06A-250 and the caps 06A-310.
(e) Assemble the single door emergency unlocking device assembly 06A-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06A-420 and to the pin 06A-410 and attach the emergency
unlocking device pivot 06A-400, the snap catch 06A-420 and the pin
For Myanmar Airways (MMA) use only
NOTE: Adjust the snap catch 06A-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06A-430 and attach the emergency unlocking device strike 06A-390 with
the bolt 06A-430 to the emergency unlocking device housing 06A-380.
(f) Attach the single door emergency unlocking device assembly 06A-370 with the
screws 06A-360 to the post assembly 06A-270.
(g) Attach the angle 06A-350 with the screws 06A-300 and the washers 06A-250
to the aft side wall assembly 06A-010.
(h) Attach the angles 06A-220 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(j) Attach the oxygen container assy 06A-230 with the screws 06A-240, 06A-245
and the washers 06A-250 to the angles 06A-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06A-230.
(l) Attach the angle 06A-190 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(m) Attach the oxygen container assy cover 06A-180 with the screws 06A-200 and
the nuts 06A-210 to the angle 06A-190.
(n) Attach the studs 06A-260 and the washers 06A-250 to the oxygen container
assy cover 06A-180.
1 Attach the special screws 06A-150 and the special washers 06A-170 to
the aft side wall assembly 06A-010.
2 Attach the handle assemblies 06A-140 to the aft side wall assembly
06A-010.
SUBTASK 25-41-58-410-030-F01
(a) Attach the fittings 06A-020, 06A-030 with the screws 06A-040, 06A-050.
(b) Attach the toilet seat-cover dispenser 06A-330 with the screws 06A-340 to
the aft side wall assembly 06A-010.
1 Attach the plates 06A-295 with the screws 06A-280 to the post assembly
06A-270.
(d) Attach the post assembly 06A-270 with the screws 06A-300, 06A-320, the
washers 06A-250 and the caps 06A-310.
(e) Assemble the single door emergency unlocking device assembly 06A-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06A-420 and to the pin 06A-410 and attach the emergency
unlocking device pivot 06A-400, the snap catch 06A-420 and the pin
NOTE: Adjust the snap catch 06A-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06A-430 and attach the emergency unlocking device strike 06A-390 with
the bolt 06A-430 to the emergency unlocking device housing 06A-380.
(f) Attach the single door emergency unlocking device assembly 06A-370 with the
screws 06A-360 to the post assembly 06A-270.
(g) Attach the angle 06A-350 with the screws 06A-300 and the washers 06A-250
For Myanmar Airways (MMA) use only
(h) Attach the angles 06A-220 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(j) Attach the oxygen container assy 06A-230 with the screws 06A-240 and the
washers 06A-250 to the angles 06A-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06A-230.
(l) Attach the angle 06A-190 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(m) Attach the oxygen container assy cover 06A-180 with the screws 06A-200 and
the nuts 06A-210 to the angle 06A-190.
(n) Attach the studs 06A-260 and the washers 06A-250 to the oxygen container
assy cover 06A-180.
1 Attach the special screws 06A-150 and the special washers 06A-170 to
the aft side wall assembly 06A-010.
2 Attach the handle assemblies 06A-140 to the aft side wall assembly
06A-010.
SUBTASK 25-41-58-410-030-H01
(a) Attach the fittings 06A-020, 06A-030 with the screws 06A-040, 06A-050.
(b) Attach the coat hook 06A-530 with the screw 06A-361 to the aft side wall
assembly 06A-010.
1 Attach the plates 06A-295 with the screws 06A-280 to the post assembly
06A-270.
(d) Attach the post assembly 06A-270 with the screws 06A-300, 06A-320, the
For Myanmar Airways (MMA) use only
(e) Assemble the single door emergency unlocking device assembly 06A-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06A-420 and to the pin 06A-410 and attach the emergency
unlocking device pivot 06A-400, the snap catch 06A-420 and the pin
06A-410 to the emergency unlocking device housing 06A-380.
NOTE: Adjust the snap catch 06A-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06A-430 and attach the emergency unlocking device strike 06A-390 with
the bolt 06A-430 to the emergency unlocking device housing 06A-380.
(f) Attach the single door emergency unlocking device assembly 06A-370 with the
screws 06A-360 to the post assembly 06A-270.
(g) Attach the angle 06A-350 with the screws 06A-300 and the washers 06A-250
to the aft side wall assembly 06A-010.
(h) Attach the angles 06A-220 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(j) Attach the oxygen container assy 06A-230 with the screws 06A-240, 06A-245
and the washers 06A-250 to the angles 06A-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06A-230.
(l) Attach the angle 06A-190 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(m) Attach the oxygen container assy cover 06A-180 with the screws 06A-200 and
the nuts 06A-210 to the angle 06A-190.
(n) Attach the studs 06A-260 and the washers 06A-250 to the oxygen container
For Myanmar Airways (MMA) use only
1 Attach the special screws 06A-150 and the special washers 06A-170 to
the aft side wall assembly 06A-010.
2 Attach the handle assemblies 06A-140 to the aft side wall assembly
06A-010.
SUBTASK 25-41-58-410-030-J01
D2549030706000
(0) Installation of the Side Wall (06A-1)
(a) Attach the fittings 06A-020, 06A-030 with the screws 06A-040, 06A-050.
(b) Attach the toilet seat-cover dispenser 06A-330 with the screws 06A-340 to
the aft side wall assembly 06A-010.
1 Attach the plates 06A-295 with the screws 06A-280 to the post assembly
06A-270.
(d) Attach the post assembly 06A-270 with the screws 06A-300, 06A-320, the
washers 06A-250 and the caps 06A-310.
(e) Assemble the single door emergency unlocking device assembly 06A-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06A-420 and to the pin 06A-410 and attach the emergency
unlocking device pivot 06A-400, the snap catch 06A-420 and the pin
06A-410 to the emergency unlocking device housing 06A-380.
NOTE: Adjust the snap catch 06A-420 a half turn before stop.
MANUFACTURER'S INSTRUCTIONS.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06A-430 and attach the emergency unlocking device strike 06A-390 with
the bolt 06A-430 to the emergency unlocking device housing 06A-380.
(f) Attach the single door emergency unlocking device assembly 06A-370 with the
screws 06A-360 to the post assembly 06A-270.
(g) Attach the angle 06A-350 with the screws 06A-300 and the washers 06A-250
to the aft side wall assembly 06A-010.
(h) Attach the angles 06A-220 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(j) Attach the oxygen container assy 06A-230 with the screws 06A-240 and the
washers 06A-250 to the angles 06A-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06A-230.
(l) Attach the hose 06A-490 to the oxygen container assy 06A-230.
(m) Attach the hose 06A-490 with the screws 06A-500, the washers 06A-510 and
the clamps 06A-520 to the aft side wall assembly 06A-010.
(n) Attach the angle 06A-190 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(p) Attach the oxygen container assy cover 06A-180 with the screws 06A-200 and
the nuts 06A-210 to the angle 06A-190.
(q) Attach the studs 06A-260 and the washers 06A-250 to the oxygen container
assy cover 06A-180.
1 Attach the special screws 06A-150 and the special washers 06A-170 to
the aft side wall assembly 06A-010.
2 Attach the handle assemblies 06A-140 to the aft side wall assembly
06A-010.
SUBTASK 25-41-58-410-030-K01
D2549030706400 D2549030714000
(0) Installation of the Side Wall (06A-1)
(a) Attach the fittings 06A-020, 06A-030 with the screws 06A-040, 06A-050.
(b) Attach the coat hook 06A-530 with the screw 06A-361 to the aft side wall
assembly 06A-010.
(c) Attach the toilet seat-cover dispenser 06A-330 with the screws 06A-340 to
the aft side wall assembly 06A-010.
1 Attach the plates 06A-295 with the screws 06A-280 to the post assembly
06A-270.
(e) Attach the post assembly 06A-270 with the screws 06A-300, 06A-320, the
washers 06A-250 and the caps 06A-310.
(f) Assemble the single door emergency unlocking device assembly 06A-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06A-420 and to the pin 06A-410 and attach the emergency
unlocking device pivot 06A-400, the snap catch 06A-420 and the pin
06A-410 to the emergency unlocking device housing 06A-380.
NOTE: Adjust the snap catch 06A-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06A-430 and attach the emergency unlocking device strike 06A-390 with
the bolt 06A-430 to the emergency unlocking device housing 06A-380.
(g) Attach the single door emergency unlocking device assembly 06A-370 with the
For Myanmar Airways (MMA) use only
(h) Attach the angle 06A-350 with the screws 06A-300 and the washers 06A-250
to the aft side wall assembly 06A-010.
(j) Attach the angles 06A-220 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(k) Attach the oxygen container assy 06A-230 with the screws 06A-240 and the
washers 06A-250 to the angles 06A-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06A-230.
(m) Attach the hose 06A-490 to the oxygen container assy 06A-230.
(n) Attach the hose 06A-490 with the screws 06A-500, the washers 06A-510 and
the clamps 06A-520 to the aft side wall assembly 06A-010.
(p) Attach the angle 06A-190 with the screws 06A-240 and the washers 06A-250
to the aft side wall assembly 06A-010.
(q) Attach the oxygen container assy cover 06A-180 with the screws 06A-200 and
the nuts 06A-210 to the angle 06A-190.
(r) Attach the studs 06A-260 and the washers 06A-250 to the oxygen container
assy cover 06A-180.
1 Attach the special screws 06A-150 and the special washers 06A-170 to
the aft side wall assembly 06A-010.
2 Attach the handle assemblies 06A-140 to the aft side wall assembly
06A-010.
TASK 25-41-58-400-819-C01
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
For Myanmar Airways (MMA) use only
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-031-A01
(a) Attach the fittings 06B-020, 06B-030 with the screws 06B-040, 06B-050.
(b) Attach the section 06B-440 with the screws 06B-200 to the aft side wall
assembly 06B-010.
For Myanmar Airways (MMA) use only
(c) Attach the screws 06B-340, 06B-475 and the washers 06B-477 to the aft side
wall assembly 06B-010.
(e) Attach the toilet seat-cover dispenser 06B-330 with the screws 06B-340 to
the aft side wall assembly 06B-010.
1 Attach the plates 06B-295 with the screws 06B-280 to the post assembly
06B-270.
(g) Attach the post assembly 06B-270 with the screws 06B-300, 06B-320, the
washers 06B-250 and the caps 06B-310.
(h) Assemble the single door emergency unlocking device assembly 06B-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06B-410 and to the pin 06B-400 and attach the emergency
unlocking device pivot 06B-390, the snap catch 06B-410 and the pin
NOTE: Adjust the snap catch 06B-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06B-420 and attach the emergency unlocking device strike 06B-380 with
the bolt 06B-420 to the emergency unlocking device housing 06B-370.
(i) Attach the single door emergency unlocking device assembly 06B-360 with the
screws 06B-430 to the post assembly 06B-270.
(j) Attach the angle 06B-350 with the screws 06B-300 and the washers 06B-250
For Myanmar Airways (MMA) use only
(k) Attach the angles 06B-220 with the screws 06B-240 and the washers 06B-250
to the aft side wall assembly 06B-010.
(l) Attach the oxygen container assy 06B-230 with the screws 06B-240, 06B-245
and the washers 06B-250 to the angles 06B-220.
(m) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06B-230.
(n) Attach the angle 06B-190 with the screws 06B-240 and the washers 06B-250
to the aft side wall assembly 06B-010.
(p) Attach the oxygen container assy cover 06B-180 with the screws 06B-200 and
the nuts 06B-210 to the angle 06B-190.
(q) Attach the studs 06B-260 and the washers 06B-250 to the oxygen container
assy cover 06B-180.
1 Attach the special screws 06B-150 and the special washers 06B-170 to
the aft side wall assembly 06B-010.
2 Attach the handle assemblies 06B-140 to the aft side wall assembly
06B-010.
SUBTASK 25-41-58-410-031-B01
(a) Attach the fittings 06B-020, 06B-030 with the screws 06B-040, 06B-050.
(b) Attach the section 06B-440 with the screws 06B-200 to the aft side wall
assembly 06B-010.
(c) Attach the screws 06B-340, 06B-475 and the washers 06B-477 to the aft side
wall assembly 06B-010.
(e) Attach the toilet seat-cover dispenser 06B-330 with the screws 06B-340 to
the aft side wall assembly 06B-010.
1 Attach the plates 06B-295 with the screws 06B-280 to the post assembly
06B-270.
(g) Attach the post assembly 06B-270 with the screws 06B-300, 06B-320, and
the washers 06B-250.
(i) Assemble the single door emergency unlocking device assembly 06B-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06B-410 and to the pin 06B-400 and attach the emergency
unlocking device pivot 06B-390, the snap catch 06B-410 and the pin
06B-400 to the emergency unlocking device housing 06B-370.
NOTE: Adjust the snap catch 06B-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06B-420 and attach the emergency unlocking device strike 06B-380 with
the bolt 06B-420 to the emergency unlocking device housing 06B-370.
(j) Attach the single door emergency unlocking device assembly 06B-360 with the
screws 06B-430 to the post assembly 06B-270.
(k) Attach the angle 06B-350 with the screws 06B-300 and the washers 06B-250
to the aft side wall assembly 06B-010.
(l) Attach the angles 06B-220 with the screws 06B-240 and the washers 06B-250
to the aft side wall assembly 06B-010.
For Myanmar Airways (MMA) use only
(m) Attach the oxygen container assy 06B-230 with the screws 06B-240, 06B-245
and the washers 06B-250 to the angles 06B-220.
(n) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06B-230.
(p) Attach the angle 06B-190 with the screws 06B-240 and the washers 06B-250
to the aft side wall assembly 06B-010.
(q) Attach the oxygen container assy cover 06B-180 with the screws 06B-200 and
the nuts 06B-210 to the angle 06B-190.
(r) Attach the studs 06B-260 and the washers 06B-250 to the oxygen container
assy cover 06B-180.
1 Attach the special screws 06B-150 and the special washers 06B-170 to
the aft side wall assembly 06B-010.
2 Attach the handle assemblies 06B-140 to the aft side wall assembly
06B-010.
SUBTASK 25-41-58-410-031-C01
D2549010414600
(a) Attach the fittings 06B-020, 06B-030 with the screws 06B-040, 06B-050.
(b) Attach the section 06B-440 with the screws 06B-200 to the aft side wall
assembly 06B-010.
(c) Attach the screws 06B-340, 06B-475 and the washers 06B-477 to the aft side
wall assembly 06B-010.
(e) Attach the toilet seat-cover dispenser 06B-330 with the screws 06B-340 to
the aft side wall assembly 06B-010.
1 Attach the plates 06B-295 with the screws 06B-280 to the post assembly
06B-270.
(g) Attach the post assembly 06B-270 with the screws 06B-300, 06B-320 and
the washers 06B-250.
(i) Assemble the single door emergency unlocking device assembly 06B-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06B-410 and to the pin 06B-400 and attach the emergency
unlocking device pivot 06B-390, the snap catch 06B-410 and the pin
06B-400 to the emergency unlocking device housing 06B-370.
NOTE: Adjust the snap catch 06B-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06B-420 and attach the emergency unlocking device strike 06B-380 with
the bolt 06B-420 to the emergency unlocking device housing 06B-370.
(j) Attach the single door emergency unlocking device assembly 06B-360 with the
screws 06B-430 to the post assembly 06B-270.
(k) Attach the angle 06B-350 with the screws 06B-300 and the washers 06B-250
to the aft side wall assembly 06B-010.
(l) Attach the angles 06B-220 with the screws 06B-240 and the washers 06B-250
to the aft side wall assembly 06B-010.
(m) Attach the oxygen container assy 06B-230 with the screws 06B-240 and the
washers 06B-250 to the angles 06B-220.
For Myanmar Airways (MMA) use only
(n) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06B-230.
(p) Attach the angle 06B-190 with the screws 06B-240 and the washers 06B-250
to the aft side wall assembly 06B-010.
(q) Attach the oxygen container assy cover 06B-180 with the screws 06B-200 and
the nuts 06B-210 to the angle 06B-190.
(r) Attach the studs 06B-260 and the washers 06B-250 to the oxygen container
assy cover 06B-180.
1 Attach the special screws 06B-150 and the special washers 06B-170 to
the aft side wall assembly 06B-010.
2 Attach the handle assemblies 06B-140 to the aft side wall assembly
06B-010.
TASK 25-41-58-400-819-D01
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-032-A01
D2549030801200
(1) Installation of the Side Wall (06C-1)
For Myanmar Airways (MMA) use only
(a) Attach the fittings 06C-020, 06C-030 with the screws 06C-040, 06C-050.
1 Attach the plates 06C-300 with the screws 06C-280 to the post assembly
06C-270.
(c) Attach the post assembly 06C-270 with the screws 06C-310, 06C-330, the
washers 06C-250 and the caps 06C-320.
(d) Assemble the single door emergency unlocking device assembly 06C-380 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06C-430 and to the pin 06C-420 and attach the emergency
unlocking device pivot 06C-410, the snap catch 06C-430 and the pin
06C-420 to the emergency unlocking device housing 06C-390.
NOTE: Adjust the snap catch 06C-430 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06C-440 and attach the emergency unlocking device strike 06C-400 with
the bolt 06C-440 to the emergency unlocking device housing 06C-390.
(e) Attach the single door emergency unlocking device assembly 06C-380 with
the screws 06C-371 to the post assembly 06C-270.
(f) Attach the angle 06C-360 with the screws 06C-310 and the washers 06C-250
to the aft side wall assembly 06C-010.
(g) Attach the angles 06C-220 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(h) Attach the oxygen container assy 06C-230 with the screws 06C-240 and the
washers 06C-250 to the angles 06C-220.
For Myanmar Airways (MMA) use only
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06C-230.
(k) Attach the angle 06C-190 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(l) Attach the oxygen container assy cover 06C-180 with the screws 06C-200 and
the nuts 06C-210 to the angle 06C-190.
(m) Attach the studs 06C-260 and the washers 06C-250 to the oxygen container
assy cover 06C-180.
1 Attach the handrails 06C-510, 06C-520 with the fastening bolts 06C-560,
the fastener assemblies 06C-540 and the bolt bushings 06C-550 to the aft
side wall assembly 06C-010.
SUBTASK 25-41-58-410-032-B01
D2549030709000
(0) Installation of the Side Wall (06C-1)
(a) Attach the fittings 06C-020, 06C-030 with the screws 06C-040, 06C-050.
(b) Attach the coat hook 06C-490 with the screw 06C-370 to the aft side wall
assembly 06C-010.
(c) Attach the toilet seat-cover dispenser 06C-340 with the screws 06C-350 to
the aft side wall assembly 06C-010.
1 Attach the plates 06C-300 with the screws 06C-280 to the post assembly
06C-270.
(e) Attach the post assembly 06C-270 with the screws 06C-310, 06C-330, the
washers 06C-250 and the caps 06C-320.
(f) Assemble the single door emergency unlocking device assembly 06C-380 as
follows:
MANUFACTURER'S INSTRUCTIONS.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06C-430 and to the pin 06C-420 and attach the emergency
unlocking device pivot 06C-410, the snap catch 06C-430 and the pin
06C-420 to the emergency unlocking device housing 06C-390.
NOTE: Adjust the snap catch 06C-430 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06C-440 and attach the emergency unlocking device strike 06C-400 with
the bolt 06C-440 to the emergency unlocking device housing 06C-390.
(g) Attach the single door emergency unlocking device assembly 06C-380 with
the screws 06C-370 to the post assembly 06C-270.
(h) Attach the angle 06C-360 with the screws 06C-310 and the washers 06C-250
to the aft side wall assembly 06C-010.
(j) Attach the angles 06C-220 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(k) Attach the oxygen container assy 06C-230 with the screws 06C-240 and the
washers 06C-250 to the angles 06C-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06C-230.
(m) Attach the hose 06C-450 to the oxygen container assy 06C-230.
(n) Attach the hose 06C-450 with the screws 06C-460, the washers 06C-470 and
the clamps 06C-480 to the aft side wall assembly 06C-010.
(p) Attach the angle 06C-190 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(q) Attach the oxygen container assy cover 06C-180 with the screws 06C-200 and
the nuts 06C-210 to the angle 06C-190.
(r) Attach the studs 06C-260 and the washers 06C-250 to the oxygen container
assy cover 06C-180.
For Myanmar Airways (MMA) use only
1 Attach the special screws 06C-150 and the special washers 06C-170 to
the aft side wall assembly 06C-010.
2 Attach the handle assemblies 06C-140 to the aft side wall assembly
06C-010.
SUBTASK 25-41-58-410-032-C01
(a) Attach the fittings 06C-020, 06C-030 with the screws 06C-040, 06C-050.
(b) Attach the coat hook 06C-490 with the screw 06C-370 to the aft side wall
assembly 06C-010.
(c) Attach the toilet seat-cover dispenser 06C-340 with the screws 06C-350 to
the aft side wall assembly 06C-010.
1 Attach the plates 06C-300 with the screws 06C-280 to the post assembly
06C-270.
(e) Attach the post assembly 06C-270 with the screws 06C-310, 06C-330, the
washers 06C-250 and the caps 06C-320.
(f) Assemble the single door emergency unlocking device assembly 06C-380 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06C-430 and to the pin 06C-420 and attach the emergency
unlocking device pivot 06C-410, the snap catch 06C-430 and the pin
06C-420 to the emergency unlocking device housing 06C-390.
NOTE: Adjust the snap catch 06C-430 a half turn before stop.
For Myanmar Airways (MMA) use only
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06C-440 and attach the emergency unlocking device strike 06C-400 with
the bolt 06C-440 to the emergency unlocking device housing 06C-390.
(g) Attach the single door emergency unlocking device assembly 06C-380 with
the screws 06C-370 to the post assembly 06C-270.
(h) Attach the angle 06C-360 with the screws 06C-310 and the washers 06C-250
to the aft side wall assembly 06C-010.
(j) Attach the angles 06C-220 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(k) Attach the oxygen container assy 06C-230 with the screws 06C-240, 06C-245
and the washers 06C-250 to the angles 06C-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06C-230.
(m) Attach the angle 06C-190 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(n) Attach the oxygen container assy cover 06C-180 with the screws 06C-200 and
the nuts 06C-210 to the angle 06C-190.
(p) Attach the studs 06C-260 and the washers 06C-250 to the oxygen container
assy cover 06C-180.
1 Attach the special screws 06C-150 and the special washers 06C-170 to
the aft side wall assembly 06C-010.
2 Attach the handle assemblies 06C-140 to the aft side wall assembly
06C-010.
SUBTASK 25-41-58-410-032-D01
(a) Attach the fittings 06C-020, 06C-030 with the screws 06C-040, 06C-050.
(b) Attach the toilet seat-cover dispenser 06C-340 with the screws 06C-350 to
the aft side wall assembly 06C-010.
1 Attach the plates 06C-300 with the screws 06C-280 to the post assembly
06C-270.
(d) Attach the post assembly 06C-270 with the screws 06C-310, 06C-330, the
washers 06C-250 and the caps 06C-320.
(e) Assemble the single door emergency unlocking device assembly 06C-380 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06C-430 and to the pin 06C-420 and attach the emergency
unlocking device pivot 06C-410, the snap catch 06C-430 and the pin
06C-420 to the emergency unlocking device housing 06C-390.
NOTE: Adjust the snap catch 06C-430 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06C-440 and attach the emergency unlocking device strike 06C-400 with
the bolt 06C-440 to the emergency unlocking device housing 06C-390.
(f) Attach the single door emergency unlocking device assembly 06C-380 with
the screws 06C-371 to the post assembly 06C-270.
(g) Attach the angle 06C-360 with the screws 06C-310 and the washers 06C-250
to the aft side wall assembly 06C-010.
(h) Attach the angles 06C-220 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
For Myanmar Airways (MMA) use only
(j) Attach the oxygen container assy 06C-230 with the screws 06C-240 and the
washers 06C-250 to the angles 06C-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06C-230.
(l) Attach the hose 06C-450 to the oxygen container assy 06C-230.
(m) Attach the hose 06C-450 with the clamps 06C-480, the screws 06C-460 and
the washers 06C-470 to the aft side wall assembly 06C-010.
(n) Attach the angle 06C-190 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(p) Attach the oxygen container assy cover 06C-180 with the screws 06C-200 and
the nuts 06C-210 to the angle 06C-190.
(q) Attach the studs 06C-260 and the washers 06C-250 to the oxygen container
assy cover 06C-180.
1 Attach the special screws 06C-150 and the special washers 06C-170 to
the aft side wall assembly 06C-010.
2 Attach the handle assemblies 06C-140 to the aft side wall assembly
06C-010.
SUBTASK 25-41-58-410-032-E01
D2549010410400
(0) Installation of the Side Wall (06C-1)
(a) Attach the fittings 06C-020, 06C-030 with the screws 06C-040, 06C-050.
(b) Attach the toilet seat-cover dispenser 06C-340 with the screws 06C-350 to
the aft side wall assembly 06C-010.
1 Attach the plates 06C-300 with the screws 06C-280 to the post assembly
06C-270.
For Myanmar Airways (MMA) use only
(d) Attach the post assembly 06C-270 with the screws 06C-310, 06C-330, the
washers 06C-250 and the caps 06C-320.
(e) Assemble the single door emergency unlocking device assembly 06C-380 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06C-430 and to the pin 06C-420 and attach the emergency
unlocking device pivot 06C-410, the snap catch 06C-430 and the pin
06C-420 to the emergency unlocking device housing 06C-390.
NOTE: Adjust the snap catch 06C-430 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06C-440 and attach the emergency unlocking device strike 06C-400 with
the bolt 06C-440 to the emergency unlocking device housing 06C-390.
(f) Attach the single door emergency unlocking device assembly 06C-380 with
the screws 06C-371 to the post assembly 06C-270.
(g) Attach the angle 06C-360 with the screws 06C-310 and the washers 06C-250
to the aft side wall assembly 06C-010.
(h) Attach the angles 06C-220 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(j) Attach the oxygen container assy 06C-230 with the screws 06C-240 and the
washers 06C-250 to the angles 06C-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06C-230.
(l) Attach the angle 06C-190 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(m) Attach the oxygen container assy cover 06C-180 with the screws 06C-200 and
For Myanmar Airways (MMA) use only
(n) Attach the studs 06C-260 and the washers 06C-250 to the oxygen container
assy cover 06C-180.
1 Attach the special screws 06C-150 and the special washers 06C-170 to
the aft side wall assembly 06C-010.
2 Attach the handle assemblies 06C-140 to the aft side wall assembly
06C-010.
SUBTASK 25-41-58-410-032-F01
D2549020310000
(0) Installation of the Side Wall (06C-1)
(a) Attach the fittings 06C-020, 06C-030 with the screws 06C-040, 06C-050.
1 Attach the plates 06C-300 with the screws 06C-280 to the post assembly
06C-270.
(c) Attach the post assembly 06C-270 with the screws 06C-310, 06C-330, the
washers 06C-250 and the caps 06C-320.
(d) Assemble the single door emergency unlocking device assembly 06C-380 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06C-430 and to the pin 06C-420 and attach the emergency
unlocking device pivot 06C-410, the snap catch 06C-430 and the pin
06C-420 to the emergency unlocking device housing 06C-390.
NOTE: Adjust the snap catch 06C-430 a half turn before stop.
MANUFACTURER'S INSTRUCTIONS.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06C-440 and attach the emergency unlocking device strike 06C-400 with
the bolt 06C-440 to the emergency unlocking device housing 06C-390.
(e) Attach the single door emergency unlocking device assembly 06C-380 with
the screws 06C-371 to the post assembly 06C-270.
(f) Attach the angle 06C-360 with the screws 06C-310 and the washers 06C-250
to the aft side wall assembly 06C-010.
(g) Attach the angles 06C-220 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(h) Attach the oxygen container assy 06C-230 with the screws 06C-240 and the
washers 06C-250 to the angles 06C-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06C-230.
(k) Attach the angle 06C-190 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(l) Attach the oxygen container assy cover 06C-180 with the screws 06C-200 and
the nuts 06C-210 to the angle 06C-190.
(m) Attach the studs 06C-260 and the washers 06C-250 to the oxygen container
assy cover 06C-180.
1 Attach the special screws 06C-150 and the special washers 06C-170 to
the aft side wall assembly 06C-010.
2 Attach the handle assemblies 06C-140 to the aft side wall assembly
06C-010.
SUBTASK 25-41-58-410-032-G01
(a) Attach the fittings 06C-020, 06C-030 with the screws 06C-040, 06C-050.
1 Attach the plates 06C-300 with the screws 06C-280 to the post assembly
06C-270.
(c) Attach the post assembly 06C-270 with the screws 06C-310, 06C-330, the
washers 06C-250 and the caps 06C-320.
(d) Assemble the single door emergency unlocking device assembly 06C-380 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06C-430 and to the pin 06C-420 and attach the emergency
unlocking device pivot 06C-410, the snap catch 06C-430 and the pin
06C-420 to the emergency unlocking device housing 06C-390.
NOTE: Adjust the snap catch 06C-430 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06C-440 and attach the emergency unlocking device strike 06C-400 with
the bolt 06C-440 to the emergency unlocking device housing 06C-390.
(e) Attach the single door emergency unlocking device assembly 06C-380 with
the screws 06C-371 to the post assembly 06C-270.
(f) Attach the angle 06C-360 with the screws 06C-310 and the washers 06C-250
to the aft side wall assembly 06C-010.
(g) Attach the angles 06C-220 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(h) Attach the oxygen container assy 06C-230 with the screws 06C-240, 06C-245
and the washers 06C-250 to the angles 06C-220.
For Myanmar Airways (MMA) use only
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06C-230.
(k) Attach the angle 06C-190 with the screws 06C-240 and the washers 06C-250
to the aft side wall assembly 06C-010.
(l) Attach the oxygen container assy cover 06C-180 with the screws 06C-200 and
the nuts 06C-210 to the angle 06C-190.
(m) Attach the studs 06C-260 and the washers 06C-250 to the oxygen container
assy cover 06C-180.
1 Attach the special screws 06C-150 and the special washers 06C-170 to
the aft side wall assembly 06C-010.
2 Attach the handle assemblies 06C-140 to the aft side wall assembly
06C-010.
TASK 25-41-58-400-819-E01
A. General
For Myanmar Airways (MMA) use only
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-033-A01
For Myanmar Airways (MMA) use only
D2549030708600 D2549030709800
(1) Installation of the Side Wall (06D-1)
(a) Attach the fittings 06D-020, 06D-030 with the screws 06D-040, 06D-050.
(b) Attach the coat hook 06D-450 with the screw 06D-351 to the aft side wall
assembly 06D-010.
(c) Attach the toilet seat-cover dispenser 06D-430 with the screws 06D-440 to
the aft side wall assembly 06D-010.
1 Attach the plates 06D-300 with the screws 06D-280 to the post assembly
06D-270.
(e) Attach the post assembly 06D-270 with the screws 06D-310, 06D-330, the
washers 06D-250 and the caps 06D-320.
(f) Assemble the single door emergency unlocking device assembly 06D-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06D-410 and to the pin 06D-400 and attach the emergency
unlocking device pivot 06D-390, the snap catch 06D-410 and the pin
NOTE: Adjust the snap catch 06D-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06D-420 and attach the emergency unlocking device strike 06D-380 with
the bolt 06D-420 to the emergency unlocking device housing 06D-370.
(g) Attach the single door emergency unlocking device assembly 06D-360 with
the screws 06D-351 to the post assembly 06D-270.
(h) Attach the angle 06D-340 with the screws 06D-310 and the washers 06D-250
For Myanmar Airways (MMA) use only
(j) Attach the angles 06D-220 with the screws 06D-240 and the washers 06D-250
to the aft side wall assembly 06D-010.
(k) Attach the oxygen container assy 06D-230 with the screws 06D-240 and the
washers 06D-250 to the angles 06D-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06D-230.
(m) Attach the angle 06D-190 with the screws 06D-240 and the washers 06D-250
to the aft side wall assembly 06D-010.
(n) Attach the hose 06D-460 to the oxygen container assy 06D-230.
(p) Attach the hose 06D-460 with the screws 06D-470, the washers 06D-480 and
the clamps 06D-490 to aft side wall assembly 06D-010.
(q) Attach the oxygen container assy cover 06D-180 with the screws 06D-200 and
the nuts 06D-210 to the angle 06D-190.
(r) Attach the studs 06D-260 and the washers 06D-250 to the oxygen container
assy cover 06D-180.
1 Attach the special screws 06D-150 and the special washers 06D-170 to
the aft side wall assembly 06D-010.
2 Attach the handle assemblies 06D-140 to the aft side wall assembly
06D-010.
SUBTASK 25-41-58-410-033-B01
D2549030706800
(0) Installation of the Side Wall (06D-1)
(a) Attach the fittings 06D-020, 06D-030 with the screws 06D-040, 06D-050.
(b) Attach the coat hook 06D-450 with the screw 06D-351 to the aft side wall
assembly 06D-010.
(c) Attach the toilet seat-cover dispenser 06D-430 with the screws 06D-440 to
For Myanmar Airways (MMA) use only
1 Attach the plates 06D-300 with the screws 06D-280 to the post assembly
06D-270.
(e) Attach the post assembly 06D-270 with the screws 06D-310, 06D-330, the
washers 06D-250 and the caps 06D-320.
(f) Assemble the single door emergency unlocking device assembly 06D-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06D-410 and to the pin 06D-400 and attach the emergency
unlocking device pivot 06D-390, the snap catch 06D-410 and the pin
06D-400 to the emergency unlocking device housing 06D-370.
NOTE: Adjust the snap catch 06D-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06D-420 and attach the emergency unlocking device strike 06D-380 with
the bolt 06D-420 to the emergency unlocking device housing 06D-370.
(g) Attach the single door emergency unlocking device assembly 06D-360 with
the screws 06D-351 to the post assembly 06D-270.
(h) Attach the angle 06D-340 with the screws 06D-310 and the washers 06D-250
to the aft side wall assembly 06D-010.
(j) Attach the angles 06D-220 with the screws 06D-240 and the washers 06D-250
to the aft side wall assembly 06D-010.
(k) Attach the oxygen container assy 06D-230 with the screws 06D-240 and the
washers 06D-250 to the angles 06D-220.
For Myanmar Airways (MMA) use only
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06D-230.
(m) Attach the angle 06D-190 with the screws 06D-240 and the washers 06D-250
to the aft side wall assembly 06D-010.
(n) Attach the oxygen container assy cover 06D-180 with the screws 06D-200 and
the nuts 06D-210 to the angle 06D-190.
(p) Attach the studs 06D-260 and the washers 06D-250 to the oxygen container
assy cover 06D-180.
1 Attach the special screws 06D-150 and the special washers 06D-170 to
the aft side wall assembly 06D-010.
2 Attach the handle assemblies 06D-140 to the aft side wall assembly
06D-010.
SUBTASK 25-41-58-410-033-C01
(a) Attach the fittings 06D-020, 06D-030 with the screws 06D-040, 06D-050.
(b) Attach the toilet seat-cover dispenser 06D-430 with the screws 06D-440 to
the aft side wall assembly 06D-010.
1 Attach the plates 06D-300 with the screws 06D-280 to the post assembly
06D-270.
(d) Attach the post assembly 06D-270 with the screws 06D-310, 06D-330, the
washers 06D-250 and the caps 06D-320.
(e) Assemble the single door emergency unlocking device assembly 06D-360 as
follows:
For Myanmar Airways (MMA) use only
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06D-410 and to the pin 06D-400 and attach the emergency
unlocking device pivot 06D-390, the snap catch 06D-410 and the pin
06D-400 to the emergency unlocking device housing 06D-370.
NOTE: Adjust the snap catch 06D-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06D-420 and attach the emergency unlocking device strike 06D-380 with
the bolt 06D-420 to the emergency unlocking device housing 06D-370.
(f) Attach the single door emergency unlocking device assembly 06D-360 with
the screws 06D-350 to the post assembly 06D-270.
(g) Attach the angle 06D-340 with the screws 06D-310 and the washers 06D-250
to the aft side wall assembly 06D-010.
(h) Attach the angles 06D-220 with the screws 06D-240 and the washers 06D-250
to the aft side wall assembly 06D-010.
(j) Attach the oxygen container assy 06D-230 with the screws 06D-240, 06D-243
and the washers 06D-250, 06D-255 to the angles 06D-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06D-230.
(l) Attach the angle 06D-190 with the screws 06D-240 and the washers 06D-250
to the aft side wall assembly 06D-010.
(m) Attach the oxygen container assy cover 06D-180 with the screws 06D-200 and
the nuts 06D-210 to the angle 06D-190.
(n) Attach the studs 06D-260 and the washers 06D-250 to the oxygen container
assy cover 06D-180.
1 Attach the special screws 06D-150 and the special washers 06D-170 to
the aft side wall assembly 06D-010.
2 Attach the handle assemblies 06D-140 to the aft side wall assembly
06D-010.
SUBTASK 25-41-58-410-033-D01
(b) Attach the fittings 06D-020, 06D-030 with the screws 06D-040, 06D-050.
(c) Attach the toilet seat-cover dispenser 06D-430 with the screws 06D-440 to
the aft side wall assembly 06D-010.
1 Attach the plates 06D-300 with the screws 06D-280 to the post assembly
06D-270.
(e) Attach the post assembly 06D-270 with the screws 06D-310, 06D-330, the
washers 06D-250 and the caps 06D-320.
(f) Assemble the single door emergency unlocking device assembly 06D-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06D-410 and to the pin 06D-400 and attach the emergency
unlocking device pivot 06D-390, the snap catch 06D-410 and the pin
06D-400 to the emergency unlocking device housing 06D-370.
NOTE: Adjust the snap catch 06D-410 a half turn before stop.
For Myanmar Airways (MMA) use only
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06D-420 and attach the emergency unlocking device strike 06D-380 with
the bolt 06D-420 to the emergency unlocking device housing 06D-370.
(g) Attach the single door emergency unlocking device assembly 06D-360 with
the screws 06D-350 to the post assembly 06D-270.
(h) Attach the angle 06D-340 with the screws 06D-310 and the washers 06D-250
to the aft side wall assembly 06D-010.
(j) Attach the angles 06D-220 with the screws 06D-240 and the washers 06D-250
to the aft side wall assembly 06D-010.
(k) Attach the oxygen container assy 06D-230 with the screws 06D-240 and the
washers 06D-250 to the angles 06D-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06D-230.
(m) Attach the angle 06D-190 with the screws 06D-240 and the washers 06D-250
to the aft side wall assembly 06D-010.
(n) Attach the oxygen container assy cover 06D-180 with the screws 06D-200 and
the nuts 06D-210 to the angle 06D-190.
(p) Attach the studs 06D-260 and the washers 06D-250 to the oxygen container
assy cover 06D-180.
1 Attach the special screws 06D-150 and the special washers 06D-170 to
the aft side wall assembly 06D-010.
2 Attach the handle assemblies 06D-140 to the aft side wall assembly
06D-010.
SUBTASK 25-41-58-410-033-E01
(a) Attach the fittings 06D-020, 06D-030 with the screws 06D-040, 06D-050.
1 Attach the plates 06D-300 with the screws 06D-280 to the post assembly
06D-270.
(c) Attach the post assembly 06D-270 with the screws 06D-310, 06D-330, the
washers 06D-250 and the caps 06D-320.
(d) Assemble the single door emergency unlocking device assembly 06D-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06D-410 and to the pin 06D-400 and attach the emergency
unlocking device pivot 06D-390, the snap catch 06D-410 and the pin
06D-400 to the emergency unlocking device housing 06D-370.
NOTE: Adjust the snap catch 06D-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06D-420 and attach the emergency unlocking device strike 06D-380 with
the bolt 06D-420 to the emergency unlocking device housing 06D-370.
(e) Attach the single door emergency unlocking device assembly 06D-360 with
the screws 06D-350 to the post assembly 06D-270.
(f) Attach the angle 06D-340 with the screws 06D-310 and the washers 06D-250
to the aft side wall assembly 06D-010.
(g) Attach the angles 06D-220 with the screws 06D-240 and the washers 06D-250
to the aft side wall assembly 06D-010.
For Myanmar Airways (MMA) use only
(h) Attach the oxygen container assy 06D-230 with the screws 06D-240 and the
washers 06D-250 to the angles 06D-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06D-230.
(k) Attach the angle 06D-190 with the screws 06D-240 and the washers 06D-250
to the aft side wall assembly 06D-010.
(l) Attach the oxygen container assy cover 06D-180 with the screws 06D-200 and
the nuts 06D-210 to the angle 06D-190.
(m) Attach the studs 06D-260 and the washers 06D-250 to the oxygen container
assy cover 06D-180.
1 Attach the special screws 06D-150 and the special washers 06D-170 to
the aft side wall assembly 06D-010.
2 Attach the handle assemblies 06D-140 to the aft side wall assembly
06D-010.
SUBTASK 25-41-58-410-033-F01
(a) Attach the fittings 06D-020, 06D-030 with the screws 06D-040, 06D-050.
1 Attach the plates 06D-300 with the screws 06D-280 to the post assembly
06D-270.
(c) Attach the post assembly 06D-270 with the screws 06D-310, 06D-330, the
washers 06D-250 and the caps 06D-320.
(d) Assemble the single door emergency unlocking device assembly 06D-360 as
follows:
For Myanmar Airways (MMA) use only
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06D-410 and to the pin 06D-400 and attach the emergency
unlocking device pivot 06D-390, the snap catch 06D-410 and the pin
06D-400 to the emergency unlocking device housing 06D-370.
NOTE: Adjust the snap catch 06D-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06D-420 and attach the emergency unlocking device strike 06D-380 with
the bolt 06D-420 to the emergency unlocking device housing 06D-370.
(e) Attach the single door emergency unlocking device assembly 06D-360 with
the screws 06D-350 to the post assembly 06D-270.
(f) Attach the angle 06D-340 with the screws 06D-310 and the washers 06D-250
to the aft side wall assembly 06D-010.
(g) Attach the angles 06D-220 with the screws 06D-240 and the washers 06D-250
to the aft side wall assembly 06D-010.
(h) Attach the oxygen container assy 06D-230 with the screws 06D-240, 06D-243
and the washers 06D-250 to the angles 06D-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06D-230.
(k) Attach the angle 06D-190 with the screws 06D-240 and the washers 06D-250
to the aft side wall assembly 06D-010.
(l) Attach the oxygen container assy cover 06D-180 with the screws 06D-200,
06D-245 and the nuts 06D-210 to the angle 06D-190.
(m) Attach the studs 06D-260 and the washers 06D-250 to the oxygen container
assy cover 06D-180.
1 Attach the special screws 06D-150 and the special washers 06D-170 to
the aft side wall assembly 06D-010.
2 Attach the handle assemblies 06D-140 to the aft side wall assembly
06D-010.
TASK 25-41-58-400-819-F01
A. General
This task gives you the installation and assembly procedures of the component.
For Myanmar Airways (MMA) use only
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-034-A01
(a) Attach the fittings 06E-020, 06E-030 with the screws 06E-040, 06E-050.
(b) Attach the toilet seat-cover dispenser 06E-430 with the screws 06E-440 to
the aft side wall assembly 06E-010.
1 Attach the plates 06E-300 with the screws 06E-280 to the post assembly
06E-270.
(d) Attach the post assembly 06E-270 with the screws 06E-310, 06E-330, the
washers 06E-250 and the caps 06E-320.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06E-410 and to the pin 06E-400 and attach the emergency
unlocking device pivot 06E-390, the snap catch 06E-410 and the pin
06E-400 to the emergency unlocking device housing 06E-370.
NOTE: Adjust the snap catch 06E-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06E-420 and attach the emergency unlocking device strike 06E-380 with
the bolt 06E-420 to the emergency unlocking device housing 06E-370.
(f) Attach the single door emergency unlocking device assembly 06E-360 with the
screws 06E-350 to the post assembly 06E-270.
(g) Attach the angle 06E-340 with the screws 06E-310 and the washers 06E-250
to the aft side wall assembly 06E-010.
(h) Attach the angles 06E-220 with the screws 06E-240 and the washers 06E-250
to the aft side wall assembly 06E-010.
For Myanmar Airways (MMA) use only
(j) Attach the oxygen container assy 06E-230 with the screws 06E-240 and the
washers 06E-250 to the angles 06E-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06E-230.
(l) Attach the angle 06E-190 with the screws 06E-240 and the washers 06E-250
to the aft side wall assembly 06E-010.
(m) Attach the oxygen container assy cover 06E-180 with the screws 06E-200 and
the nuts 06E-210 to the angle 06E-190.
(n) Attach the studs 06E-260 and the washers 06E-250 to the oxygen container
assy cover 06E-180.
1 Attach the screws 06E-470 and the washers 06E-480 to the aft side wall
assembly 06E-010.
2 Attach the handle 06E-460 to the screws 06E-470 and hold with the
setscrews 06E-490.
SUBTASK 25-41-58-410-034-B01
(a) Attach the fittings 06E-020, 06E-030 with the screws 06E-040, 06E-050.
(b) Attach the coat hook 06E-500 with the screw 06E-351 to the aft side wall
assembly 06E-010.
(c) Attach the toilet seat-cover dispenser 06E-430 with the screws 06E-440 to
the aft side wall assembly 06E-010.
1 Attach the plates 06E-300 with the screws 06E-280 to the post assembly
06E-270.
(e) Attach the post assembly 06E-270 with the screws 06E-310, 06E-330, the
washers 06E-250 and the caps 06E-320.
For Myanmar Airways (MMA) use only
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06E-410 and to the pin 06E-400 and attach the emergency
unlocking device pivot 06E-390, the snap catch 06E-410 and the pin
06E-400 to the emergency unlocking device housing 06E-370.
NOTE: Adjust the snap catch 06E-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06E-420 and attach the emergency unlocking device strike 06E-380 with
the bolt 06E-420 to the emergency unlocking device housing 06E-370.
(g) Attach the single door emergency unlocking device assembly 06E-360 with the
screws 06E-350 to the post assembly 06E-270.
(h) Attach the angle 06E-340 with the screws 06E-310 and the washers 06E-250
to the aft side wall assembly 06E-010.
(j) Attach the angles 06E-220 with the screws 06E-240 and the washers 06E-250
to the aft side wall assembly 06E-010.
(k) Attach the oxygen container assy 06E-230 with the screws 06E-240 and the
washers 06E-250 to the angles 06E-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06E-230.
(m) Attach the angle 06E-190 with the screws 06E-240 and the washers 06E-250
to the aft side wall assembly 06E-010.
(n) Attach the oxygen container assy cover 06E-180 with the screws 06E-200 and
the nuts 06E-210 to the angle 06E-190.
(p) Attach the studs 06E-260 and the washers 06E-250 to the oxygen container
For Myanmar Airways (MMA) use only
1 Attach the special screws 06E-150 and the special washers 06E-170 to
the aft side wall assembly 06E-010.
2 Attach the handle assemblies 06E-140 to the aft side wall assembly
06E-010.
SUBTASK 25-41-58-410-034-C01
(a) Attach the fittings 06E-020, 06E-030 with the screws 06E-040, 06E-050.
(b) Attach the toilet seat-cover dispenser 06E-430 with the screws 06E-440 to
the aft side wall assembly 06E-010.
1 Attach the plates 06E-300 with the screws 06E-280 to the post assembly
06E-270.
(d) Attach the post assembly 06E-270 with the screws 06E-310, 06E-330, the
washers 06E-250 and the caps 06E-320.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06E-410 and to the pin 06E-400 and attach the emergency
unlocking device pivot 06E-390, the snap catch 06E-410 and the pin
06E-400 to the emergency unlocking device housing 06E-370.
NOTE: Adjust the snap catch 06E-410 a half turn before stop.
For Myanmar Airways (MMA) use only
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06E-420 and attach the emergency unlocking device strike 06E-380 with
the bolt 06E-420 to the emergency unlocking device housing 06E-370.
(f) Attach the single door emergency unlocking device assembly 06E-360 with the
screws 06E-350 to the post assembly 06E-270.
(g) Attach the angle 06E-340 with the screws 06E-310 and the washers 06E-250
to the aft side wall assembly 06E-010.
(h) Attach the angles 06E-220 with the screws 06E-240 and the washers 06E-250
to the aft side wall assembly 06E-010.
(j) Attach the oxygen container assy 06E-230 with the screws 06E-240, 06E-241
and the washers 06E-250 to the angles 06E-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06E-230.
(l) Attach the angle 06E-190 with the screws 06E-240 and the washers 06E-250
to the aft side wall assembly 06E-010.
(m) Attach the oxygen container assy cover 06E-180 with the screws 06E-200,
06E-243 and the nuts 06E-210 to the angle 06E-190.
(n) Attach the studs 06E-260 and the washers 06E-250 to the oxygen container
assy cover 06E-180.
1 Attach the special screws 06E-150 and the special washers 06E-170 to
the aft side wall assembly 06E-010.
2 Attach the handle assemblies 06E-140 to the aft side wall assembly
06E-010.
SUBTASK 25-41-58-410-034-D01
D2549020306000 R225401807-000
For Myanmar Airways (MMA) use only
(a) Attach the fittings 06E-020, 06E-030 with the screws 06E-040, 06E-050.
(b) Attach the toilet seat-cover dispenser 06E-430 with the screws 06E-440 to
the aft side wall assembly 06E-010.
1 Attach the plates 06E-300 with the screws 06E-280 to the post assembly
06E-270.
(d) Attach the post assembly 06E-270 with the screws 06E-310, 06E-330, the
washers 06E-250 and the caps 06E-320.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06E-410 and to the pin 06E-400 and attach the emergency
unlocking device pivot 06E-390, the snap catch 06E-410 and the pin
06E-400 to the emergency unlocking device housing 06E-370.
NOTE: Adjust the snap catch 06E-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06E-420 and attach the emergency unlocking device strike 06E-380 with
the bolt 06E-420 to the emergency unlocking device housing 06E-370.
(f) Attach the single door emergency unlocking device assembly 06E-360 with the
screws 06E-350 to the post assembly 06E-270.
(g) Attach the angle 06E-340 with the screws 06E-310 and the washers 06E-250
to the aft side wall assembly 06E-010.
(h) Attach the angles 06E-220 with the screws 06E-240 and the washers 06E-250
to the aft side wall assembly 06E-010.
For Myanmar Airways (MMA) use only
(j) Attach the oxygen container assy 06E-230 with the screws 06E-240, 06E-241
and the washers 06E-250 to the angles 06E-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06E-230.
(l) Attach the angle 06E-190 with the screws 06E-240 and the washers 06E-250
to the aft side wall assembly 06E-010.
(m) Attach the oxygen container assy cover 06E-180 with the screws 06E-200 and
the nuts 06E-210 to the angle 06E-190.
(n) Attach the studs 06E-260 and the washers 06E-250 to the oxygen container
assy cover 06E-180.
1 Attach the special screws 06E-150 and the special washers 06E-170 to
the aft side wall assembly 06E-010.
2 Attach the handle assemblies 06E-140 to the aft side wall assembly
06E-010.
SUBTASK 25-41-58-410-034-E01
(a) Attach the fittings 06E-020, 06E-030 with the screws 06E-040, 06E-050.
(b) Attach the screws 06E-440 to the aft side wall assembly 06E-010.
1 Attach the plates 06E-300 with the screws 06E-280 to the post assembly
06E-270.
(d) Attach the post assembly 06E-270 with the screws 06E-310, 06E-330, the
washers 06E-250 and the caps 06E-320.
For Myanmar Airways (MMA) use only
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06E-410 and to the pin 06E-400 and attach the emergency
unlocking device pivot 06E-390, the snap catch 06E-410 and the pin
06E-400 to the emergency unlocking device housing 06E-370.
NOTE: Adjust the snap catch 06E-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06E-420 and attach the emergency unlocking device strike 06E-380 with
the bolt 06E-420 to the emergency unlocking device housing 06E-370.
(f) Attach the single door emergency unlocking device assembly 06E-360 with the
screws 06E-350 to the post assembly 06E-270.
(g) Attach the angle 06E-340 with the screws 06E-310 and the washers 06E-250
to the aft side wall assembly 06E-010.
(h) Attach the angles 06E-220 with the screws 06E-240 and the washers 06E-250
to the aft side wall assembly 06E-010.
(j) Attach the oxygen container assy 06E-230 with the screws 06E-240, 06E-241
and the washers 06E-250 to the angles 06E-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06E-230.
(l) Attach the angle 06E-190 with the screws 06E-240 and the washers 06E-250
to the aft side wall assembly 06E-010.
(m) Attach the oxygen container assy cover 06E-180 with the screws 06E-200 and
the nuts 06E-210 to the angle 06E-190.
(n) Attach the studs 06E-260 and the washers 06E-250 to the oxygen container
For Myanmar Airways (MMA) use only
1 Attach the special screws 06E-150 and the special washers 06E-170 to
the aft side wall assembly 06E-010.
2 Attach the handle assemblies 06E-140 to the aft side wall assembly
06E-010.
TASK 25-41-58-400-819-G01
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-035-A01
D2549020902600
(1) Installation of the Side Wall (06F-1)
For Myanmar Airways (MMA) use only
(a) Attach the fittings 06F-020, 06F-030 with the screws 06F-040, 06F-050.
(b) Attach the coat hook 06F-460 with the screw 06F-431 to the aft side wall
assembly 06F-010.
(c) Attach the toilet seat-cover dispenser 06F-440 with the screws 06F-450 to
the aft side wall assembly 06F-010.
1 Attach the plates 06F-260 with the screws 06F-240 to the post assembly
06F-230.
(e) Attach the post assembly 06F-230 with the screws 06F-270, 06F-290, the
washers 06F-210 and the caps 06F-280.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06F-410 and to the pin 06F-400 and attach the emergency
unlocking device pivot 06F-390, the snap catch 06F-410 and the pin
06F-400 to the emergency unlocking device housing 06F-370.
NOTE: Adjust the snap catch 06F-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06F-420 and attach the emergency unlocking device strike 06F-380 with
the bolt 06F-420 to the emergency unlocking device housing 06F-370.
(g) Attach the single door emergency unlocking device assembly 06F-360 with the
screws 06F-430 to the post assembly 06F-230.
(h) Attach the angle 06F-350 with the screws 06F-270 and the washers 06F-210 to
the aft side wall assembly 06F-010.
(j) Attach the angles 06F-180 with the screws 06F-200 and the washers 06F-210
to the aft side wall assembly 06F-010.
For Myanmar Airways (MMA) use only
(k) Attach the oxygen container assy 06F-190 with the screws 06F-200 and the
washers 06F-210 to the angles 06F-180.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06F-190.
(m) Attach the angle 06F-150 with the screws 06F-200 and the washers 06F-210 to
the aft side wall assembly 06F-010.
(n) Attach the oxygen container assy cover 06F-140 with the screws 06F-160 and
the nuts 06F-170 to the angle 06F-150.
(p) Attach the studs 06F-220 and the washers 06F-210 to the oxygen container
assy cover 06F-140.
(q) Attach the support 06F-340 with the screws 06F-270 and the washers 06F-210
to the aft side wall assembly 06F-010.
1 Attach the special screws 06F-310 and the special washers 06F-330 to
the aft side wall assembly 06F-010.
2 Attach the handle assembly 06F-300 to the aft side wall assembly
06F-010.
SUBTASK 25-41-58-410-035-B01
(a) Attach the fittings 06F-020, 06F-030 with the screws 06F-040, 06F-050.
(b) Attach the toilet seat-cover dispenser 06F-440 with the screws 06F-450 to
the aft side wall assembly 06F-010.
1 Attach the plates 06F-260 with the screws 06F-240 to the post assembly
06F-230.
(d) Attach the post assembly 06F-230 with the screws 06F-270, 06F-290, the
For Myanmar Airways (MMA) use only
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06F-410 and to the pin 06F-400 and attach the emergency
unlocking device pivot 06F-390, the snap catch 06F-410 and the pin
06F-400 to the emergency unlocking device housing 06F-370.
NOTE: Adjust the snap catch 06F-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06F-420 and attach the emergency unlocking device strike 06F-380 with
the bolt 06F-420 to the emergency unlocking device housing 06F-370.
(f) Attach the single door emergency unlocking device assembly 06F-360 with the
screws 06F-430 to the post assembly 06F-230.
(g) Attach the angle 06F-350 with the screws 06F-270 and the washers 06F-210 to
the aft side wall assembly 06F-010.
(h) Attach the angles 06F-180 with the screws 06F-200 and the washers 06F-210
to the aft side wall assembly 06F-010.
(j) Attach the oxygen container assy 06F-190 with the screws 06F-200, 06F-205
and the washers 06F-210 to the angles 06F-180.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06F-190.
(l) Attach the angle 06F-150 with the screws 06F-200 and the washers 06F-210 to
the aft side wall assembly 06F-010.
(m) Attach the oxygen container assy cover 06F-140 with the screws 06F-160 and
the nuts 06F-170 to the angle 06F-150.
(n) Attach the studs 06F-220 and the washers 06F-210 to the oxygen container
For Myanmar Airways (MMA) use only
(p) Attach the support 06F-340 with the screws 06F-270 and the washers 06F-210
to the aft side wall assembly 06F-010.
1 Attach the special screws 06F-310 and the special washers 06F-330 to
the aft side wall assembly 06F-010.
2 Attach the handle assembly 06F-300 to the aft side wall assembly
06F-010.
SUBTASK 25-41-58-410-035-C01
D2549010409200 D2549010410200
(0) Installation of the Side Wall (06F-1)
(a) Attach the fittings 06F-020, 06F-030 with the screws 06F-040, 06F-050.
(b) Attach the toilet seat-cover dispenser 06F-440 with the screws 06F-450 to
the aft side wall assembly 06F-010.
1 Attach the plates 06F-260 with the screws 06F-240 to the post assembly
06F-230.
(d) Attach the post assembly 06F-230 with the screws 06F-270, 06F-290, the
washers 06F-210 and the caps 06F-280.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06F-410 and to the pin 06F-400 and attach the emergency
unlocking device pivot 06F-390, the snap catch 06F-410 and the pin
06F-400 to the emergency unlocking device housing 06F-370.
NOTE: Adjust the snap catch 06F-410 a half turn before stop.
For Myanmar Airways (MMA) use only
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06F-420 and attach the emergency unlocking device strike 06F-380 with
the bolt 06F-420 to the emergency unlocking device housing 06F-370.
(f) Attach the single door emergency unlocking device assembly 06F-360 with the
screws 06F-430 to the post assembly 06F-230.
(g) Attach the angle 06F-350 with the screws 06F-270 and the washers 06F-210 to
the aft side wall assembly 06F-010.
(h) Attach the angles 06F-180 with the screws 06F-200 and the washers 06F-210
to the aft side wall assembly 06F-010.
(j) Attach the oxygen container assy 06F-190 with the screws 06F-200 and the
washers 06F-210 to the angles 06F-180.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06F-190.
(l) Attach the angle 06F-150 with the screws 06F-200 and the washers 06F-210 to
the aft side wall assembly 06F-010.
(m) Attach the oxygen container assy cover 06F-140 with the screws 06F-160 and
the nuts 06F-170 to the angle 06F-150.
(n) Attach the studs 06F-220 and the washers 06F-210 to the oxygen container
assy cover 06F-140.
(p) Attach the support 06F-340 with the screws 06F-270 and the washers 06F-210
to the aft side wall assembly 06F-010.
1 Attach the special screws 06F-310 and the special washers 06F-330 to
the aft side wall assembly 06F-010.
2 Attach the handle assembly 06F-300 to the aft side wall assembly
06F-010.
SUBTASK 25-41-58-410-035-D01
D2549040503400
(0) Installation of the Side Wall (06F-1)
(a) Attach the fittings 06F-020, 06F-030 with the screws 06F-040, 06F-050.
(b) Attach the toilet seat-cover dispenser 06F-440 with the screws 06F-450 to
the aft side wall assembly 06F-010.
1 Attach the plates 06F-260 with the screws 06F-240 to the post assembly
06F-230.
(d) Attach the post assembly 06F-230 with the screws 06F-270, 06F-290, the
washers 06F-210 and the caps 06F-280.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06F-410 and to the pin 06F-400 and attach the emergency
unlocking device pivot 06F-390, the snap catch 06F-410 and the pin
NOTE: Adjust the snap catch 06F-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06F-420 and attach the emergency unlocking device strike 06F-380 with
the bolt 06F-420 to the emergency unlocking device housing 06F-370.
(f) Attach the single door emergency unlocking device assembly 06F-360 with the
screws 06F-430 to the post assembly 06F-230.
(g) Attach the angle 06F-350 with the screws 06F-270 and the washers 06F-210 to
For Myanmar Airways (MMA) use only
(h) Attach the angles 06F-180 with the screws 06F-200 and the washers 06F-210
to the aft side wall assembly 06F-010.
(j) Attach the oxygen container assy 06F-190 with the screws 06F-200 and the
washers 06F-210 to the angles 06F-180.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06F-190.
(l) Attach the angle 06F-150 with the screws 06F-200 and the washers 06F-210 to
the aft side wall assembly 06F-010.
(m) Attach the oxygen container assy cover 06F-140 with the screws 06F-160 and
the nuts 06F-170 to the angle 06F-150.
(n) Attach the studs 06F-220 and the washers 06F-210 to the oxygen container
assy cover 06F-140.
1 Attach the special screws 06F-310 and the special washers 06F-330 to
the aft side wall assembly 06F-010.
2 Attach the handle assembly 06F-300 to the aft side wall assembly
06F-010.
SUBTASK 25-41-58-410-035-E01
(a) Attach the fittings 06F-020, 06F-030 with the screws 06F-040, 06F-050.
1 Attach the plates 06F-260 with the screws 06F-240 to the post assembly
06F-230.
(c) Attach the post assembly 06F-230 with the screws 06F-270, 06F-290, the
washers 06F-210 and the caps 06F-280.
For Myanmar Airways (MMA) use only
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06F-410 and to the pin 06F-400 and attach the emergency
unlocking device pivot 06F-390, the snap catch 06F-410 and the pin
06F-400 to the emergency unlocking device housing 06F-370.
NOTE: Adjust the snap catch 06F-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06F-420 and attach the emergency unlocking device strike 06F-380 with
the bolt 06F-420 to the emergency unlocking device housing 06F-370.
(e) Attach the single door emergency unlocking device assembly 06F-360 with the
screws 06F-430 to the post assembly 06F-230.
(f) Attach the angle 06F-350 with the screws 06F-270 and the washers 06F-210 to
the aft side wall assembly 06F-010.
(g) Attach the angles 06F-180 with the screws 06F-200 and the washers 06F-210
to the aft side wall assembly 06F-010.
(h) Attach the oxygen container assy 06F-190 with the screws 06F-200, 06F-205
and the washers 06F-210 to the angles 06F-180.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06F-190.
(k) Attach the angle 06F-150 with the screws 06F-200 and the washers 06F-210 to
the aft side wall assembly 06F-010.
(l) Attach the oxygen container assy cover 06F-140 with the screws 06F-160 and
the nuts 06F-170 to the angle 06F-150.
(m) Attach the studs 06F-220 and the washers 06F-210 to the oxygen container
For Myanmar Airways (MMA) use only
(n) Attach the support 06F-340 with the screws 06F-270 and the washers 06F-210
to the aft side wall assembly 06F-010.
1 Attach the special screws 06F-310 and the special washers 06F-330 to
the aft side wall assembly 06F-010.
2 Attach the handle assembly 06F-300 to the aft side wall assembly
06F-010.
SUBTASK 25-41-58-410-035-F01
D2547160900800
(0) Installation of the Side Wall (06F-1)
(a) Attach the fittings 06F-020, 06F-030 with the screws 06F-040, 06F-050.
1 Attach the plates 06F-260 with the screws 06F-240 to the post assembly
06F-230.
(c) Attach the post assembly 06F-230 with the screws 06F-270, 06F-290, the
washers 06F-210 and the caps 06F-280.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06F-410 and to the pin 06F-400 and attach the emergency
unlocking device pivot 06F-390, the snap catch 06F-410 and the pin
06F-400 to the emergency unlocking device housing 06F-370.
NOTE: Adjust the snap catch 06F-410 a half turn before stop.
MANUFACTURER'S INSTRUCTIONS.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06F-420 and attach the emergency unlocking device strike 06F-380 with
the bolt 06F-420 to the emergency unlocking device housing 06F-370.
(e) Attach the single door emergency unlocking device assembly 06F-360 with the
screws 06F-430 to the post assembly 06F-230.
(f) Attach the angle 06F-350 with the screws 06F-270 and the washers 06F-210 to
the aft side wall assembly 06F-010.
(g) Attach the angles 06F-180 with the screws 06F-200 and the washers 06F-210
to the aft side wall assembly 06F-010.
(h) Attach the oxygen container assy 06F-190 with the screws 06F-200 and the
washers 06F-210 to the angles 06F-180.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06F-190.
(k) Attach the angle 06F-150 with the screws 06F-200 and the washers 06F-210 to
the aft side wall assembly 06F-010.
(l) Attach the oxygen container assy cover 06F-140 with the screws 06F-160 and
the nuts 06F-170 to the angle 06F-150.
(m) Attach the studs 06F-220 and the washers 06F-210 to the oxygen container
assy cover 06F-140.
(n) Attach the support 06F-340 with the screws 06F-270 and the washers 06F-210
to the aft side wall assembly 06F-010.
1 Attach the special screws 06F-310 and the special washers 06F-330 to
the aft side wall assembly 06F-010.
2 Attach the handle assembly 06F-300 to the aft side wall assembly
06F-010.
TASK 25-41-58-400-819-H01
D2549010408200
96. Installation of the Side Wall
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-036-A01
D2549010408200
(1) Installation of the Side Wall (06G-1)
(a) Attach the fittings 06G-020, 06G-030 with the screws 06G-040, 06G-050.
(b) Attach the lavatory picture frame kit 06G-450 with the screws 06G-350 to the
aft side wall assembly 06G-010.
For Myanmar Airways (MMA) use only
(c) Attach the toilet seat-cover dispenser 06G-340 with the screws 06G-350 to
the aft side wall assembly 06G-010.
1 Attach the plates 06G-300 with the screws 06G-280 to the post assembly
06G-270.
(e) Attach the post assembly 06G-270 with the screws 06G-310, 06G-330, the
washers 06G-250 and the caps 06G-320.
(f) Assemble the single door emergency unlocking device assembly 06G-380 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06G-430 and to the pin 06G-420 and attach the emergency
unlocking device pivot 06G-410, the snap catch 06G-430 and the pin
06G-420 to the emergency unlocking device housing 06G-390.
NOTE: Adjust the snap catch 06G-430 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06G-440 and attach the emergency unlocking device strike 06G-400 with
the bolt 06G-440 to the emergency unlocking device housing 06G-390.
(g) Attach the single door emergency unlocking device assembly 06G-380 with
the screws 06G-370 to the post assembly 06G-270.
(h) Attach the angle 06G-360 with the screws 06G-310 and the washers 06G-250
to the aft side wall assembly 06G-010.
(j) Attach the angles 06G-220 with the screws 06G-240 and the washers 06G-250
to the aft side wall assembly 06G-010.
(k) Attach the oxygen container assy 06G-230 with the screws 06G-240 and the
washers 06G-250 to the angles 06G-220.
For Myanmar Airways (MMA) use only
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06G-230.
(m) Attach the angle 06G-190 with the screws 06G-240 and the washers 06G-250
to the aft side wall assembly 06G-010.
(n) Attach the oxygen container assy cover 06G-180 with the screws 06G-200 and
the nuts 06G-210 to the angle 06G-190.
(p) Attach the studs 06G-260 and the washers 06G-250 to the oxygen container
assy cover 06G-180.
1 Attach the special screws 06G-150 and the special washers 06G-170 to
the aft side wall assembly 06G-010.
2 Attach the handle assemblies 06G-140 to the aft side wall assembly
06G-010.
TASK 25-41-58-400-819-J01
97. Installation of the Side Wall
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-037-A01
D2549030712200 D2549030808000
(1) Installation of the Side Wall (06H-1)
(a) Attach the fittings 06H-020, 06H-030 with the screws 06H-040, 06H-050.
1 Attach the plates 06H-300 with the screws 06H-280 to the post assembly
06H-270.
(c) Attach the post assembly 06H-270 with the screws 06H-310, 06H-330, the
For Myanmar Airways (MMA) use only
(d) Assemble the single door emergency unlocking device assembly 06H-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06H-410 and to the pin 06H-400 and attach the emergency
unlocking device pivot 06H-390, the snap catch 06H-410 and the pin
06H-400 to the emergency unlocking device housing 06H-370.
NOTE: Adjust the snap catch 06H-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06H-420 and attach the emergency unlocking device strike 06H-380 with
the bolt 06H-420 to the emergency unlocking device housing 06H-370.
(e) Attach the single door emergency unlocking device assembly 06H-360 with
the screws 06H-350 to the post assembly 06H-270.
(f) Attach the angle 06H-340 with the screws 06H-310 and the washers 06H-250
to the aft side wall assembly 06H-010.
(g) Attach the angles 06H-220 with the screws 06H-240 and the washers 06H-250
to the aft side wall assembly 06H-010.
(h) Attach the oxygen container assy 06H-230 with the screws 06H-240 and the
washers 06H-250 to the angles 06H-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06H-230.
(k) Attach the angle 06H-190 with the screws 06H-240 and the washers 06H-250
to the aft side wall assembly 06H-010.
(l) Attach the oxygen container assy cover 06H-180 with the screws 06H-200 and
the nuts 06H-210 to the angle 06H-190.
(m) Attach the studs 06H-260 and the washers 06H-250 to the oxygen container
For Myanmar Airways (MMA) use only
1 Attach the screws 06H-450 and the washers 06H-460 to the aft side wall
assembly 06H-010.
2 Attach the handle 06H-440 to the screws 06H-450 and hold with the
setscrews 06H-470.
SUBTASK 25-41-58-410-037-B01
(a) Attach the fittings 06H-020, 06H-030 with the screws 06H-040, 06H-050.
(b) Attach the toilet seat-cover dispenser 06H-480 with the screws 06H-490 to
the aft side wall assembly 06H-010.
1 Attach the plates 06H-300 with the screws 06H-280 to the post assembly
06H-270.
(d) Attach the post assembly 06H-270 with the screws 06H-310, 06H-330, the
washers 06H-250 and the caps 06H-320.
(e) Assemble the single door emergency unlocking device assembly 06H-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06H-410 and to the pin 06H-400 and attach the emergency
unlocking device pivot 06H-390, the snap catch 06H-410 and the pin
06H-400 to the emergency unlocking device housing 06H-370.
NOTE: Adjust the snap catch 06H-410 a half turn before stop.
MANUFACTURER'S INSTRUCTIONS.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06H-420 and attach the emergency unlocking device strike 06H-380 with
the bolt 06H-420 to the emergency unlocking device housing 06H-370.
(f) Attach the single door emergency unlocking device assembly 06H-360 with
the screws 06H-350 to the post assembly 06H-270.
(g) Attach the angle 06H-340 with the screws 06H-310 and the washers 06H-250
to the aft side wall assembly 06H-010.
(h) Attach the angles 06H-220 with the screws 06H-240 and the washers 06H-250
to the aft side wall assembly 06H-010.
(j) Attach the oxygen container assy 06H-230 with the screws 06H-240, 06H-245
and the washers 06H-250 to the angles 06H-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06H-230.
(l) Attach the angle 06H-190 with the screws 06H-240 and the washers 06H-250
to the aft side wall assembly 06H-010.
(m) Attach the oxygen container assy cover 06H-180 with the screws 06H-200 and
the nuts 06H-210 to the angle 06H-190.
(n) Attach the studs 06H-260 and the washers 06H-250 to the oxygen container
assy cover 06H-180.
1 Attach the special screws 06H-150 and the special washers 06H-170 to
the aft side wall assembly 06H-010.
2 Attach the handle assemblies 06H-140 to the aft side wall assembly
06H-010.
SUBTASK 25-41-58-410-037-C01
(a) Attach the fittings 06H-020, 06H-030 with the screws 06H-040, 06H-050.
(b) Attach the toilet seat-cover dispenser 06H-480 with the screws 06H-490 to
the aft side wall assembly 06H-010.
1 Attach the plates 06H-300 with the screws 06H-280 to the post assembly
06H-270.
(d) Attach the post assembly 06H-270 with the screws 06H-310, 06H-330, the
washers 06H-250 and the caps 06H-320.
(e) Assemble the single door emergency unlocking device assembly 06H-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06H-410 and to the pin 06H-400 and attach the emergency
unlocking device pivot 06H-390, the snap catch 06H-410 and the pin
06H-400 to the emergency unlocking device housing 06H-370.
NOTE: Adjust the snap catch 06H-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06H-420 and attach the emergency unlocking device strike 06H-380 with
the bolt 06H-420 to the emergency unlocking device housing 06H-370.
(f) Attach the single door emergency unlocking device assembly 06H-360 with
the screws 06H-350 to the post assembly 06H-270.
(g) Attach the angle 06H-340 with the screws 06H-310 and the washers 06H-250
to the aft side wall assembly 06H-010.
(h) Attach the angles 06H-220 with the screws 06H-240 and the washers 06H-250
to the aft side wall assembly 06H-010.
For Myanmar Airways (MMA) use only
(j) Attach the oxygen container assy 06H-230 with the screws 06H-240 and the
washers 06H-250 to the angles 06H-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06H-230.
(l) Attach the angle 06H-190 with the screws 06H-240 and the washers 06H-250
to the aft side wall assembly 06H-010.
(m) Attach the oxygen container assy cover 06H-180 with the screws 06H-200 and
the nuts 06H-210 to the angle 06H-190.
(n) Attach the studs 06H-260 and the washers 06H-250 to the oxygen container
assy cover 06H-180.
1 Attach the special screws 06H-150 and the special washers 06H-170 to
the aft side wall assembly 06H-010.
2 Attach the handle assemblies 06H-140 to the aft side wall assembly
06H-010.
SUBTASK 25-41-58-410-037-D01
(a) Attach the fittings 06H-020, 06H-030 with the screws 06H-040, 06H-050.
1 Attach the plates 06H-300 with the screws 06H-280 to the post assembly
06H-270.
(c) Attach the post assembly 06H-270 with the screws 06H-310, 06H-330, the
washers 06H-250 and the caps 06H-320.
(d) Assemble the single door emergency unlocking device assembly 06H-360 as
For Myanmar Airways (MMA) use only
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06H-410 and to the pin 06H-400 and attach the emergency
unlocking device pivot 06H-390, the snap catch 06H-410 and the pin
06H-400 to the emergency unlocking device housing 06H-370.
NOTE: Adjust the snap catch 06H-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06H-420 and attach the emergency unlocking device strike 06H-380 with
the bolt 06H-420 to the emergency unlocking device housing 06H-370.
(e) Attach the single door emergency unlocking device assembly 06H-360 with
the screws 06H-350 to the post assembly 06H-270.
(f) Attach the angle 06H-340 with the screws 06H-310 and the washers 06H-250
to the aft side wall assembly 06H-010.
(g) Attach the angles 06H-220 with the screws 06H-240 and the washers 06H-250
to the aft side wall assembly 06H-010.
(h) Attach the oxygen container assy 06H-230 with the screws 06H-240, 06H-245
and the washers 06H-250 to the angles 06H-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06H-230.
(k) Attach the angle 06H-190 with the screws 06H-240 and the washers 06H-250
to the aft side wall assembly 06H-010.
(l) Attach the oxygen container assy cover 06H-180 with the screws 06H-200 and
the nuts 06H-210 to the angle 06H-190.
(m) Attach the studs 06H-260 and the washers 06H-250 to the oxygen container
assy cover 06H-180.
1 Attach the special screws 06H-150 and the special washers 06H-170 to
the aft side wall assembly 06H-010.
2 Attach the handle assemblies 06H-140 to the aft side wall assembly
06H-010.
SUBTASK 25-41-58-410-037-E01
D2549030710800 R225401136-002
(0) Installation of the Side Wall (06H-1)
(a) Attach the fittings 06H-020, 06H-030 with the screws 06H-040, 06H-050.
1 Attach the plates 06H-300 with the screws 06H-280 to the post assembly
06H-270.
(c) Attach the post assembly 06H-270 with the screws 06H-310, 06H-330, the
washers 06H-250 and the caps 06H-320.
(d) Assemble the single door emergency unlocking device assembly 06H-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06H-410 and to the pin 06H-400 and attach the emergency
unlocking device pivot 06H-390, the snap catch 06H-410 and the pin
06H-400 to the emergency unlocking device housing 06H-370.
NOTE: Adjust the snap catch 06H-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
For Myanmar Airways (MMA) use only
06H-420 and attach the emergency unlocking device strike 06H-380 with
the bolt 06H-420 to the emergency unlocking device housing 06H-370.
(e) Attach the single door emergency unlocking device assembly 06H-360 with
the screws 06H-350 to the post assembly 06H-270.
(f) Attach the angle 06H-340 with the screws 06H-310 and the washers 06H-250
to the aft side wall assembly 06H-010.
(g) Attach the angles 06H-220 with the screws 06H-240 and the washers 06H-250
to the aft side wall assembly 06H-010.
(h) Attach the oxygen container assy 06H-230 with the screws 06H-240, 06H-245
and the washers 06H-250 to the angles 06H-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06H-230.
(k) Attach the angle 06H-190 with the screws 06H-240 and the washers 06H-250
to the aft side wall assembly 06H-010.
(l) Attach the oxygen container assy cover 06H-180 with the screws 06H-200 and
the nuts 06H-210 to the angle 06H-190.
(m) Attach the studs 06H-260 and the washers 06H-250 to the oxygen container
assy cover 06H-180.
1 Attach the special screws 06H-150 and the special washers 06H-170 to
the aft side wall assembly 06H-010.
2 Attach the handle assemblies 06H-140 to the aft side wall assembly
06H-010.
TASK 25-41-58-400-819-K01
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-038-A01
D2549010410600 D2549020901000
(1) Installation of the Side Wall (06J-1)
For Myanmar Airways (MMA) use only
(a) Attach the fittings 06J-020, 06J-030 with the screws 06J-040, 06J-050.
(b) Attach the coat hook 06J-450 with the screw 06J-351 to the aft side wall
assembly 06J-010.
(c) Attach the toilet seat-cover dispenser 06J-430 with the screws 06J-440 to
the aft side wall assembly 06J-010.
1 Attach the plates 06J-300 with the screws 06J-280 to the post assembly
06J-270.
(e) Attach the post assembly 06J-270 with the screws 06J-310, 06J-330, the
washers 06J-250 and the caps 06J-320.
(f) Assemble the single door emergency unlocking device assembly 06J-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06J-410 and to the pin 06J-400 and attach the emergency unlocking
device pivot 06J-390, the snap catch 06J-410 and the pin 06J-400 to the
emergency unlocking device housing 06J-370.
NOTE: Adjust the snap catch 06J-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06J-420 and attach the emergency unlocking device strike 06J-380 with
the bolt 06J-420 to the emergency unlocking device housing 06J-370.
(g) Attach the single door emergency unlocking device assembly 06J-360 with the
screws 06J-350 to the post assembly 06J-270.
(h) Attach the angle 06J-340 with the screws 06J-310 and the washers 06J-250 to
the aft side wall assembly 06J-010.
(j) Attach the angles 06J-220 with the screws 06J-240 and the washers 06J-250
to the aft side wall assembly 06J-010.
For Myanmar Airways (MMA) use only
(k) Attach the oxygen container assy 06J-230 with the screws 06J-240 and the
washers 06J-250 to the angles 06J-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06J-230.
(m) Attach the angle 06J-190 with the screws 06J-240 and the washers 06J-250 to
the aft side wall assembly 06J-010.
(n) Attach the oxygen container assy cover 06J-180 with the screws 06J-200 and
the nuts 06J-210 to the angle 06J-190.
(p) Attach the studs 06J-260 and the washers 06J-250 to the oxygen container
assy cover 06J-180.
1 Attach the special screws 06J-150 and the special washers 06J-170 to
the aft side wall assembly 06J-010.
2 Attach the handle assemblies 06J-140 to the aft side wall assembly
06J-010.
SUBTASK 25-41-58-410-038-B01
D2549020901800 R225401822-004
(a) Attach the fittings 06J-020, 06J-030 with the screws 06J-040, 06J-050.
(b) Attach the coat hook 06J-450 with the screw 06J-351 to the aft side wall
assembly 06J-010.
1 Attach the plates 06J-300 with the screws 06J-280 to the post assembly
06J-270.
(d) Attach the post assembly 06J-270 with the screws 06J-310, 06J-330, the
washers 06J-250 and the caps 06J-320.
(e) Assemble the single door emergency unlocking device assembly 06J-360 as
For Myanmar Airways (MMA) use only
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06J-410 and to the pin 06J-400 and attach the emergency unlocking
device pivot 06J-390, the snap catch 06J-410 and the pin 06J-400 to the
emergency unlocking device housing 06J-370.
NOTE: Adjust the snap catch 06J-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06J-420 and attach the emergency unlocking device strike 06J-380 with
the bolt 06J-420 to the emergency unlocking device housing 06J-370.
(f) Attach the single door emergency unlocking device assembly 06J-360 with the
screws 06J-350 to the post assembly 06J-270.
(g) Attach the angle 06J-340 with the screws 06J-310 and the washers 06J-250 to
the aft side wall assembly 06J-010.
(h) Attach the angles 06J-220 with the screws 06J-240 and the washers 06J-250
to the aft side wall assembly 06J-010.
(j) Attach the oxygen container assy 06J-230 with the screws 06J-240, 06J-245
and the washers 06J-250 to the angles 06J-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06J-230.
(l) Attach the angle 06J-190 with the screws 06J-240 and the washers 06J-250 to
the aft side wall assembly 06J-010.
(m) Attach the oxygen container assy cover 06J-180 with the screws 06J-200 and
the nuts 06J-210 to the angle 06J-190.
(n) Attach the studs 06J-260 and the washers 06J-250 to the oxygen container
assy cover 06J-180.
1 Attach the special screws 06J-150 and the special washers 06J-170 to
the aft side wall assembly 06J-010.
2 Attach the handle assemblies 06J-140 to the aft side wall assembly
06J-010.
SUBTASK 25-41-58-410-038-C01
(a) Attach the fittings 06J-020, 06J-030 with the screws 06J-040, 06J-050.
(b) Attach the toilet seat-cover dispenser 06J-430 with the screws 06J-440 to
the aft side wall assembly 06J-010.
1 Attach the plates 06J-300 with the screws 06J-280 to the post assembly
06J-270.
(d) Attach the post assembly 06J-270 with the screws 06J-310, 06J-330, the
washers 06J-250 and the caps 06J-320.
(e) Assemble the single door emergency unlocking device assembly 06J-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06J-410 and to the pin 06J-400 and attach the emergency unlocking
device pivot 06J-390, the snap catch 06J-410 and the pin 06J-400 to the
emergency unlocking device housing 06J-370.
NOTE: Adjust the snap catch 06J-410 a half turn before stop.
MANUFACTURER'S INSTRUCTIONS.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06J-420 and attach the emergency unlocking device strike 06J-380 with
the bolt 06J-420 to the emergency unlocking device housing 06J-370.
(f) Attach the single door emergency unlocking device assembly 06J-360 with the
screws 06J-350 to the post assembly 06J-270.
(g) Attach the angle 06J-340 with the screws 06J-310 and the washers 06J-250 to
the aft side wall assembly 06J-010.
(h) Attach the angles 06J-220 with the screws 06J-240 and the washers 06J-250
to the aft side wall assembly 06J-010.
(j) Attach the oxygen container assy 06J-230 with the screws 06J-240 and the
washers 06J-250 to the angles 06J-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06J-230.
(l) Attach the angle 06J-190 with the screws 06J-240 and the washers 06J-250 to
the aft side wall assembly 06J-010.
(m) Attach the oxygen container assy cover 06J-180 with the screws 06J-200 and
the nuts 06J-210 to the angle 06J-190.
(n) Attach the studs 06J-260 and the washers 06J-250 to the oxygen container
assy cover 06J-180.
1 Attach the special screws 06J-150 and the special washers 06J-170 to
the aft side wall assembly 06J-010.
2 Attach the handle assemblies 06J-140 to the aft side wall assembly
06J-010.
SUBTASK 25-41-58-410-038-D01
D2549040503800 R225401673-014
(0) Installation of the Side Wall (06J-1)
(a) Attach the fittings 06J-020, 06J-030 with the screws 06J-040, 06J-050.
For Myanmar Airways (MMA) use only
(b) Attach the toilet seat-cover dispenser 06J-430 with the screws 06J-440 to
the aft side wall assembly 06J-010.
1 Attach the plates 06J-300 with the screws 06J-280 to the post assembly
06J-270.
(d) Attach the post assembly 06J-270 with the screws 06J-310, 06J-330, the
washers 06J-250 and the caps 06J-320.
(e) Assemble the single door emergency unlocking device assembly 06J-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06J-410 and to the pin 06J-400 and attach the emergency unlocking
device pivot 06J-390, the snap catch 06J-410 and the pin 06J-400 to the
emergency unlocking device housing 06J-370.
NOTE: Adjust the snap catch 06J-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06J-420 and attach the emergency unlocking device strike 06J-380 with
the bolt 06J-420 to the emergency unlocking device housing 06J-370.
(f) Attach the single door emergency unlocking device assembly 06J-360 with the
screws 06J-350 to the post assembly 06J-270.
(g) Attach the angle 06J-340 with the screws 06J-310 and the washers 06J-250 to
the aft side wall assembly 06J-010.
(h) Attach the angles 06J-220 with the screws 06J-240 and the washers 06J-250
to the aft side wall assembly 06J-010.
(j) Attach the oxygen container assy 06J-230 with the screws 06J-240 and the
washers 06J-250 to the angles 06J-220.
For Myanmar Airways (MMA) use only
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06J-230.
(l) Attach the angle 06J-190 with the screws 06J-240 and the washers 06J-250 to
the aft side wall assembly 06J-010.
(m) Attach the oxygen container assy cover 06J-180 with the screws 06J-200 and
the nuts 06J-210 to the angle 06J-190.
(n) Attach the studs 06J-260 and the washers 06J-250 to the oxygen container
assy cover 06J-180.
1 Attach the special screws 06J-150 and the special washers 06J-170 to
the aft side wall assembly 06J-010.
2 Attach the handle assemblies 06J-140 to the aft side wall assembly
06J-010.
SUBTASK 25-41-58-410-038-E01
D2549020900800 D2549040504000
(0) Installation of the Side Wall (06J-1)
(a) Attach the fittings 06J-020, 06J-030 with the screws 06J-040, 06J-050.
1 Attach the plates 06J-300 with the screws 06J-280 to the post assembly
06J-270.
(c) Attach the post assembly 06J-270 with the screws 06J-310, 06J-330, the
washers 06J-250 and the caps 06J-320.
(d) Assemble the single door emergency unlocking device assembly 06J-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
For Myanmar Airways (MMA) use only
catch 06J-410 and to the pin 06J-400 and attach the emergency unlocking
device pivot 06J-390, the snap catch 06J-410 and the pin 06J-400 to the
emergency unlocking device housing 06J-370.
NOTE: Adjust the snap catch 06J-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06J-420 and attach the emergency unlocking device strike 06J-380 with
the bolt 06J-420 to the emergency unlocking device housing 06J-370.
(e) Attach the single door emergency unlocking device assembly 06J-360 with the
screws 06J-350 to the post assembly 06J-270.
(f) Attach the angle 06J-340 with the screws 06J-310 and the washers 06J-250 to
the aft side wall assembly 06J-010.
(g) Attach the angles 06J-220 with the screws 06J-240 and the washers 06J-250
to the aft side wall assembly 06J-010.
(h) Attach the oxygen container assy 06J-230 with the screws 06J-240 and the
washers 06J-250 to the angles 06J-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06J-230.
(k) Attach the angle 06J-190 with the screws 06J-240 and the washers 06J-250 to
the aft side wall assembly 06J-010.
(l) Attach the oxygen container assy cover 06J-180 with the screws 06J-200 and
the nuts 06J-210 to the angle 06J-190.
(m) Attach the studs 06J-260 and the washers 06J-250 to the oxygen container
assy cover 06J-180.
1 Attach the special screws 06J-150 and the special washers 06J-170 to
the aft side wall assembly 06J-010.
2 Attach the handle assemblies 06J-140 to the aft side wall assembly
06J-010.
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-410-038-F01
D2549020903800 D2549026000800
(0) Installation of the Side Wall (06J-1)
(a) Attach the fittings 06J-020, 06J-030 with the screws 06J-040, 06J-050.
1 Attach the plates 06J-300 with the screws 06J-280 to the post assembly
06J-270.
(c) Attach the post assembly 06J-270 with the screws 06J-310, 06J-330, the
washers 06J-250 and the caps 06J-320.
(d) Assemble the single door emergency unlocking device assembly 06J-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06J-410 and to the pin 06J-400 and attach the emergency unlocking
device pivot 06J-390, the snap catch 06J-410 and the pin 06J-400 to the
NOTE: Adjust the snap catch 06J-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06J-420 and attach the emergency unlocking device strike 06J-380 with
the bolt 06J-420 to the emergency unlocking device housing 06J-370.
(e) Attach the single door emergency unlocking device assembly 06J-360 with the
screws 06J-350 to the post assembly 06J-270.
(f) Attach the angle 06J-340 with the screws 06J-310 and the washers 06J-250 to
For Myanmar Airways (MMA) use only
(g) Attach the angles 06J-220 with the screws 06J-240 and the washers 06J-250
to the aft side wall assembly 06J-010.
(h) Attach the oxygen container assy 06J-230 with the screws 06J-240 and the
washers 06J-250 to the angles 06J-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06J-230.
(k) Attach the angle 06J-190 with the screws 06J-240 and the washers 06J-250 to
the aft side wall assembly 06J-010.
(l) Attach the oxygen container assy cover 06J-180 with the screws 06J-200 and
the nuts 06J-210 to the angle 06J-190.
(m) Attach the studs 06J-260 and the washers 06J-250 to the oxygen container
assy cover 06J-180.
1 Attach the special screws 06J-150 and the special washers 06J-170 to
the aft side wall assembly 06J-010.
2 Attach the handle assemblies 06J-140 to the aft side wall assembly
06J-010.
TASK 25-41-58-400-819-L01
A. General
For Myanmar Airways (MMA) use only
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-039-A01
For Myanmar Airways (MMA) use only
(a) Attach the fittings 06K-020, 06K-030 with the screws 06K-040, 06K-050.
(b) Attach the coat hook 06K-500 with the screw 06K-361 to the aft side wall
assembly 06K-010.
(c) Attach the toilet seat-cover dispenser 06K-440 with the screws 06K-450 to
the aft side wall assembly 06K-010.
1 Attach the plates 06K-310 with the screws 06K-290 to the post assembly
06K-280.
(e) Attach the post assembly 06K-280 with the screws 06K-320, 06K-340, the
washers 06K-260 and the caps 06K-330.
(f) Assemble the single door emergency unlocking device assembly 06K-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06K-420 and to the pin 06K-410 and attach the emergency
unlocking device pivot 06K-400, the snap catch 06K-420 and the pin
06K-410 to the emergency unlocking device housing 06K-380.
NOTE: Adjust the snap catch 06K-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06K-430 and attach the emergency unlocking device strike 06K-390 with
the bolt 06K-430 to the emergency unlocking device housing 06K-380.
(g) Attach the single door emergency unlocking device assembly 06K-370 with the
screws 06K-360 to the post assembly 06K-280.
For Myanmar Airways (MMA) use only
(h) Attach the angle 06K-350 with the screws 06K-320 and the washers 06K-260
to the aft side wall assembly 06K-010.
(j) Attach the angles 06K-230 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(k) Attach the oxygen container assy 06K-240 with the screws 06K-250 and the
washers 06K-260 to the angles 06K-230.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06K-240.
(m) Attach the angle 06K-200 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(n) Attach the oxygen container assy cover 06K-190 with the screws 06K-210 and
the nuts 06K-220 to the angle 06K-200.
(p) Attach the studs 06K-270 and the washers 06K-260 to the oxygen container
assy cover 06K-190.
1 Attach the special screws 06K-470 and the special washers 06K-490 to
the aft side wall assembly 06K-010.
2 Attach the handle assemblies 06K-460 to the aft side wall assembly
06K-010.
SUBTASK 25-41-58-410-039-B01
(a) Attach the fittings 06K-020, 06K-030 with the screws 06K-040, 06K-050.
(b) Attach the coat hook 06K-500 with the screw 06K-361 to the aft side wall
assembly 06K-010.
1 Attach the plates 06K-310 with the screws 06K-290 to the post assembly
For Myanmar Airways (MMA) use only
06K-280.
(d) Attach the post assembly 06K-280 with the screws 06K-320, 06K-340, the
washers 06K-260 and the caps 06K-330.
(e) Assemble the single door emergency unlocking device assembly 06K-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06K-420 and to the pin 06K-410 and attach the emergency
unlocking device pivot 06K-400, the snap catch 06K-420 and the pin
06K-410 to the emergency unlocking device housing 06K-380.
NOTE: Adjust the snap catch 06K-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06K-430 and attach the emergency unlocking device strike 06K-390 with
the bolt 06K-430 to the emergency unlocking device housing 06K-380.
(f) Attach the single door emergency unlocking device assembly 06K-370 with the
screws 06K-360 to the post assembly 06K-280.
(g) Attach the angle 06K-350 with the screws 06K-320 and the washers 06K-260
to the aft side wall assembly 06K-010.
(h) Attach the angles 06K-230 with the screws 06K-250, 06K-255 and the washers
06K-260 to the aft side wall assembly 06K-010.
(j) Attach the oxygen container assy 06K-240 with the screws 06K-250 and the
washers 06K-260 to the angles 06K-230.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06K-240.
(l) Attach the angle 06K-200 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(m) Attach the oxygen container assy cover 06K-190 with the screws 06K-210 and
For Myanmar Airways (MMA) use only
(n) Attach the studs 06K-270 and the washers 06K-260 to the oxygen container
assy cover 06K-190.
1 Attach the special screws 06K-470 and the special washers 06K-490 to
the aft side wall assembly 06K-010.
2 Attach the handle assemblies 06K-460 to the aft side wall assembly
06K-010.
SUBTASK 25-41-58-410-039-C01
D2549020905200 D2549030807200
(0) Installation of the Side Wall (06K-1)
(a) Attach the fittings 06K-020, 06K-030 with the screws 06K-040, 06K-050.
(b) Attach the toilet seat-cover dispenser 06K-440 with the screws 06K-450 to
the aft side wall assembly 06K-010.
1 Attach the plates 06K-310 with the screws 06K-290 to the post assembly
06K-280.
(d) Attach the post assembly 06K-280 with the screws 06K-320, 06K-340, the
washers 06K-260 and the caps 06K-330.
(e) Assemble the single door emergency unlocking device assembly 06K-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06K-420 and to the pin 06K-410 and attach the emergency
unlocking device pivot 06K-400, the snap catch 06K-420 and the pin
06K-410 to the emergency unlocking device housing 06K-380.
NOTE: Adjust the snap catch 06K-420 a half turn before stop.
For Myanmar Airways (MMA) use only
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06K-430 and attach the emergency unlocking device strike 06K-390 with
the bolt 06K-430 to the emergency unlocking device housing 06K-380.
(f) Attach the single door emergency unlocking device assembly 06K-370 with the
screws 06K-360 to the post assembly 06K-280.
(g) Attach the angle 06K-350 with the screws 06K-320 and the washers 06K-260
to the aft side wall assembly 06K-010.
(h) Attach the angles 06K-230 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(j) Attach the oxygen container assy 06K-240 with the screws 06K-250 and the
washers 06K-260 to the angles 06K-230.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06K-240.
(l) Attach the angle 06K-200 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(m) Attach the oxygen container assy cover 06K-190 with the screws 06K-210 and
the nuts 06K-220 to the angle 06K-200.
(n) Attach the studs 06K-270 and the washers 06K-260 to the oxygen container
assy cover 06K-190.
1 Attach the special screws 06K-470 and the special washers 06K-490 to
the aft side wall assembly 06K-010.
2 Attach the handle assemblies 06K-460 to the aft side wall assembly
06K-010.
SUBTASK 25-41-58-410-039-D01
(a) Attach the fittings 06K-020, 06K-030 with the screws 06K-040, 06K-050.
(b) Attach the toilet seat-cover dispenser 06K-440 with the screws 06K-450 to
the aft side wall assembly 06K-010.
1 Attach the plates 06K-310 with the screws 06K-290 to the post assembly
06K-280.
(d) Attach the post assembly 06K-280 with the screws 06K-320, 06K-340, the
washers 06K-260 and the caps 06K-330.
(e) Assemble the single door emergency unlocking device assembly 06K-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06K-420 and to the pin 06K-410 and attach the emergency
unlocking device pivot 06K-400, the snap catch 06K-420 and the pin
06K-410 to the emergency unlocking device housing 06K-380.
NOTE: Adjust the snap catch 06K-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06K-430 and attach the emergency unlocking device strike 06K-390 with
the bolt 06K-430 to the emergency unlocking device housing 06K-380.
(f) Attach the single door emergency unlocking device assembly 06K-370 with the
screws 06K-360 to the post assembly 06K-280.
(g) Attach the angle 06K-350 with the screws 06K-320 and the washers 06K-260
to the aft side wall assembly 06K-010.
(h) Attach the angles 06K-230 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
For Myanmar Airways (MMA) use only
(j) Attach the oxygen container assy 06K-240 with the screws 06K-250 and the
washers 06K-260 to the angles 06K-230.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06K-240.
(l) Attach the angle 06K-200 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(m) Attach the oxygen container assy cover 06K-190 with the screws 06K-210 and
the nuts 06K-220 to the angle 06K-200.
(n) Attach the studs 06K-270 and the washers 06K-260 to the oxygen container
assy cover 06K-190.
1 Attach the special screws 06K-470 and the special washers 06K-490 to
the aft side wall assembly 06K-010.
2 Attach the handle assemblies 06K-460 to the aft side wall assembly
06K-010.
SUBTASK 25-41-58-410-039-E01
(a) Attach the fittings 06K-020, 06K-030 with the screws 06K-040, 06K-050.
(b) Attach the toilet seat-cover dispenser 06K-440 with the screws 06K-450 to
the aft side wall assembly 06K-010.
1 Attach the plates 06K-310 with the screws 06K-290 to the post assembly
06K-280.
(d) Attach the post assembly 06K-280 with the screws 06K-320, 06K-340, the
washers 06K-260 and the caps 06K-330.
(e) Assemble the single door emergency unlocking device assembly 06K-370 as
For Myanmar Airways (MMA) use only
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06K-420 and to the pin 06K-410 and attach the emergency
unlocking device pivot 06K-400, the snap catch 06K-420 and the pin
06K-410 to the emergency unlocking device housing 06K-380.
NOTE: Adjust the snap catch 06K-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06K-430 and attach the emergency unlocking device strike 06K-390 with
the bolt 06K-430 to the emergency unlocking device housing 06K-380.
(f) Attach the single door emergency unlocking device assembly 06K-370 with the
screws 06K-360 to the post assembly 06K-280.
(g) Attach the angle 06K-350 with the screws 06K-320 and the washers 06K-260
to the aft side wall assembly 06K-010.
(h) Attach the angles 06K-230 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(j) Attach the oxygen container assy 06K-240 with the screws 06K-250, 06K-255
and the washers 06K-260 to the angles 06K-230.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06K-240.
(l) Attach the angle 06K-200 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(m) Attach the oxygen container assy cover 06K-190 with the screws 06K-210 and
the nuts 06K-220 to the angle 06K-200.
(n) Attach the studs 06K-270 and the washers 06K-260 to the oxygen container
assy cover 06K-190.
1 Attach the screws 06K-160 and the washers 06K-170 to the aft side wall
assembly 06K-010.
2 Attach the handle 06K-150 to the screws 06K-160 and hold with the
setscrews 06K-180.
SUBTASK 25-41-58-410-039-F01
(a) Attach the fittings 06K-020, 06K-030 with the screws 06K-040, 06K-050.
1 Attach the plates 06K-310 with the screws 06K-290 to the post assembly
06K-280.
(c) Attach the post assembly 06K-280 with the screws 06K-320, 06K-340, the
washers 06K-260 and the caps 06K-330.
(d) Assemble the single door emergency unlocking device assembly 06K-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06K-420 and to the pin 06K-410 and attach the emergency
unlocking device pivot 06K-400, the snap catch 06K-420 and the pin
06K-410 to the emergency unlocking device housing 06K-380.
NOTE: Adjust the snap catch 06K-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06K-430 and attach the emergency unlocking device strike 06K-390 with
the bolt 06K-430 to the emergency unlocking device housing 06K-380.
(e) Attach the single door emergency unlocking device assembly 06K-370 with the
For Myanmar Airways (MMA) use only
(f) Attach the angle 06K-350 with the screws 06K-320 and the washers 06K-260
to the aft side wall assembly 06K-010.
(g) Attach the angles 06K-230 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(h) Attach the oxygen container assy 06K-240 with the screws 06K-250 and the
washers 06K-260 to the angles 06K-230.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06K-240.
(k) Attach the angle 06K-200 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(l) Attach the oxygen container assy cover 06K-190 with the screws 06K-210 and
the nuts 06K-220 to the angle 06K-200.
(m) Attach the studs 06K-270 and the washers 06K-260 to the oxygen container
assy cover 06K-190.
1 Attach the screws 06K-160 and the washers 06K-170 to the aft side wall
assembly 06K-010.
2 Attach the handle 06K-150 to the screws 06K-160 and hold with the
setscrews 06K-180.
SUBTASK 25-41-58-410-039-G01
(a) Attach the fittings 06K-020, 06K-030 with the screws 06K-040, 06K-050.
1 Attach the plates 06K-310 with the screws 06K-290 to the post assembly
06K-280.
For Myanmar Airways (MMA) use only
(c) Attach the post assembly 06K-280 with the screws 06K-320, 06K-340, the
washers 06K-260 and the caps 06K-330.
(d) Assemble the single door emergency unlocking device assembly 06K-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06K-420 and to the pin 06K-410 and attach the emergency
unlocking device pivot 06K-400, the snap catch 06K-420 and the pin
06K-410 to the emergency unlocking device housing 06K-380.
NOTE: Adjust the snap catch 06K-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06K-430 and attach the emergency unlocking device strike 06K-390 with
the bolt 06K-430 to the emergency unlocking device housing 06K-380.
(e) Attach the single door emergency unlocking device assembly 06K-370 with the
screws 06K-360 to the post assembly 06K-280.
(f) Attach the angle 06K-350 with the screws 06K-320 and the washers 06K-260
to the aft side wall assembly 06K-010.
(g) Attach the angles 06K-230 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(h) Attach the oxygen container assy 06K-240 with the screws 06K-250, 06K-255
and the washers 06K-260 to the angles 06K-230.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06K-240.
(k) Attach the angle 06K-200 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(l) Attach the oxygen container assy cover 06K-190 with the screws 06K-210 and
For Myanmar Airways (MMA) use only
(m) Attach the studs 06K-270 and the washers 06K-260 to the oxygen container
assy cover 06K-190.
1 Attach the special screws 06K-470 and the special washers 06K-490 to
the aft side wall assembly 06K-010.
2 Attach the handle assemblies 06K-460 to the aft side wall assembly
06K-010.
SUBTASK 25-41-58-410-039-H01
(a) Attach the fittings 06K-020, 06K-030 with the screws 06K-040, 06K-050.
1 Attach the plates 06K-310 with the screws 06K-290 to the post assembly
06K-280.
(c) Attach the post assembly 06K-280 with the screws 06K-320, 06K-340, the
washers 06K-260 and the caps 06K-330.
(d) Assemble the single door emergency unlocking device assembly 06K-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06K-420 and to the pin 06K-410 and attach the emergency
unlocking device pivot 06K-400, the snap catch 06K-420 and the pin
06K-410 to the emergency unlocking device housing 06K-380.
NOTE: Adjust the snap catch 06K-420 a half turn before stop.
MANUFACTURER'S INSTRUCTIONS.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06K-430 and attach the emergency unlocking device strike 06K-390 with
the bolt 06K-430 to the emergency unlocking device housing 06K-380.
(e) Attach the single door emergency unlocking device assembly 06K-370 with the
screws 06K-360 to the post assembly 06K-280.
(f) Attach the angle 06K-350 with the screws 06K-320 and the washers 06K-260
to the aft side wall assembly 06K-010.
(g) Attach the angles 06K-230 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(h) Attach the oxygen container assy 06K-240 with the screws 06K-250 and the
washers 06K-260 to the angles 06K-230.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06K-240.
(k) Attach the angle 06K-200 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(l) Attach the oxygen container assy cover 06K-190 with the screws 06K-210 and
the nuts 06K-220 to the angle 06K-200.
(m) Attach the studs 06K-270 and the washers 06K-260 to the oxygen container
assy cover 06K-190.
1 Attach the special screws 06K-470 and the special washers 06K-490 to
the aft side wall assembly 06K-010.
2 Attach the handle assemblies 06K-460 to the aft side wall assembly
06K-010.
SUBTASK 25-41-58-410-039-J01
(a) Attach the fittings 06K-020, 06K-030 with the screws 06K-040, 06K-050.
For Myanmar Airways (MMA) use only
1 Attach the plates 06K-310 with the screws 06K-290 to the post assembly
06K-280.
(c) Attach the post assembly 06K-280 with the screws 06K-320, 06K-340, the
washers 06K-260 and the caps 06K-330.
(d) Assemble the single door emergency unlocking device assembly 06K-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06K-420 and to the pin 06K-410 and attach the emergency
unlocking device pivot 06K-400, the snap catch 06K-420 and the pin
06K-410 to the emergency unlocking device housing 06K-380.
NOTE: Adjust the snap catch 06K-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06K-430 and attach the emergency unlocking device strike 06K-390 with
(e) Attach the single door emergency unlocking device assembly 06K-370 with the
screws 06K-360 to the post assembly 06K-280.
(f) Attach the angle 06K-350 with the screws 06K-320 and the washers 06K-260
to the aft side wall assembly 06K-010.
(g) Attach the angles 06K-230 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(h) Attach the oxygen container assy 06K-240 with the screws 06K-250, 06K-255
and the washers 06K-260 to the angles 06K-230.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06K-240.
For Myanmar Airways (MMA) use only
(k) Attach the angle 06K-200 with the screws 06K-250 and the washers 06K-260
to the aft side wall assembly 06K-010.
(l) Attach the oxygen container assy cover 06K-190 with the screws 06K-210 and
the nuts 06K-220 to the angle 06K-200.
(m) Attach the studs 06K-270 and the washers 06K-260 to the oxygen container
assy cover 06K-190.
1 Attach the special screws 06K-470 and the special washers 06K-490 to
the aft side wall assembly 06K-010.
2 Attach the handle assemblies 06K-460 to the aft side wall assembly
06K-010.
TASK 25-41-58-400-819-M01
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-040-A01
D2549020907000
(1) Installation of the Side Wall (06L-1)
For Myanmar Airways (MMA) use only
(a) Attach the fittings 06L-020, 06L-030 with the screws 06L-040, 06L-050.
1 Attach the plates 06L-260 with the screws 06L-240 to the post assembly
06L-230.
(c) Attach the post assembly 06L-230 with the screws 06L-270, 06L-290, the
washers 06L-210 and the caps 06L-280, 06L-281.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06L-410 and to the pin 06L-400 and attach the emergency unlocking
device pivot 06L-390, the snap catch 06L-410 and the pin 06L-400 to the
emergency unlocking device housing 06L-370.
NOTE: Adjust the snap catch 06L-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06L-420 and attach the emergency unlocking device strike 06L-380 with
the bolt 06L-420 to the emergency unlocking device housing 06L-370.
(e) Attach the single door emergency unlocking device assembly 06L-360 with the
screws 06L-430 to the post assembly 06L-230.
(f) Attach the angle 06L-350 with the screws 06L-270 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(g) Attach the angles 06L-180 with the screws 06L-200 and the washers 06L-210
to the aft side wall assembly 06L-010.
(h) Attach the oxygen container assy 06L-190 with the screws 06L-200 and the
washers 06L-210 to the angles 06L-180.
For Myanmar Airways (MMA) use only
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06L-190.
(k) Attach the angle 06L-150 with the screws 06L-200 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(l) Attach the oxygen container assy cover 06L-140 with the screws 06L-160 and
the nuts 06L-170 to the angle 06L-150.
(m) Attach the studs 06L-220 and the washers 06L-210 to the oxygen container
assy cover 06L-140.
(n) Attach the support 06L-340 with the screws 06L-440 and the washers 06L-210
to the aft side wall assembly 06L-010.
1 Attach the special screws 06L-310 and the special washers 06L-330 to
the aft side wall assembly 06L-010.
2 Attach the handle assembly 06L-300 to the aft side wall assembly
06L-010.
SUBTASK 25-41-58-410-040-B01
D2549020908200
(0) Installation of the Side Wall (06L-1)
(a) Attach the fittings 06L-020, 06L-030 with the screws 06L-040, 06L-050.
(b) Attach the coat hook 06L-450 with the screw 06L-431 to the aft side wall
assembly 06L-010.
(c) Attach the toilet seat-cover dispenser 06L-460 with the screws 06L-470 to
the aft side wall assembly 06L-010.
1 Attach the plates 06L-260 with the screws 06L-240 to the post assembly
06L-230.
(e) Attach the post assembly 06L-230 with the screws 06L-270, 06L-290, the
washers 06L-210 and the caps 06L-280.
For Myanmar Airways (MMA) use only
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06L-410 and to the pin 06L-400 and attach the emergency unlocking
device pivot 06L-390, the snap catch 06L-410 and the pin 06L-400 to the
emergency unlocking device housing 06L-370.
NOTE: Adjust the snap catch 06L-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06L-420 and attach the emergency unlocking device strike 06L-380 with
the bolt 06L-420 to the emergency unlocking device housing 06L-370.
(g) Attach the single door emergency unlocking device assembly 06L-360 with the
screws 06L-430 to the post assembly 06L-230.
(h) Attach the angle 06L-350 with the screws 06L-270 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(j) Attach the angles 06L-180 with the screws 06L-200 and the washers 06L-210
to the aft side wall assembly 06L-010.
(k) Attach the oxygen container assy 06L-190 with the screws 06L-200 and the
washers 06L-210 to the angles 06L-180.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06L-190.
(m) Attach the angle 06L-150 with the screws 06L-200 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(n) Attach the oxygen container assy cover 06L-140 with the screws 06L-160 and
the nuts 06L-170 to the angle 06L-150.
(p) Attach the studs 06L-220 and the washers 06L-210 to the oxygen container
For Myanmar Airways (MMA) use only
(q) Attach the support 06L-340 with the screws 06L-440 and the washers 06L-210
to the aft side wall assembly 06L-010.
1 Attach the special screws 06L-310 and the special washers 06L-330 to
the aft side wall assembly 06L-010.
2 Attach the handle assembly 06L-300 to the aft side wall assembly
06L-010.
SUBTASK 25-41-58-410-040-C01
D2549020913200
(0) Installation of the Side Wall (06L-1)
(a) Attach the fittings 06L-020, 06L-030 with the screws 06L-040, 06L-050.
1 Attach the plates 06L-260 with the screws 06L-240 to the post assembly
06L-230.
(c) Attach the post assembly 06L-230 with the screws 06L-270, 06L-290 and the
washers 06L-210.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06L-410 and to the pin 06L-400 and attach the emergency unlocking
device pivot 06L-390, the snap catch 06L-410 and the pin 06L-400 to the
emergency unlocking device housing 06L-370.
For Myanmar Airways (MMA) use only
NOTE: Adjust the snap catch 06L-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06L-420 and attach the emergency unlocking device strike 06L-380 with
the bolt 06L-420 to the emergency unlocking device housing 06L-370.
(f) Attach the single door emergency unlocking device assembly 06L-360 with the
screws 06L-430 to the post assembly 06L-230.
(g) Attach the angle 06L-350 with the screws 06L-270 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(h) Attach the angles 06L-180 with the screws 06L-200 and the washers 06L-210
to the aft side wall assembly 06L-010.
(j) Attach the oxygen container assy 06L-190 with the screws 06L-200 and the
washers 06L-210 to the angles 06L-180.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06L-190.
(l) Attach the angle 06L-150 with the screws 06L-200 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(m) Attach the oxygen container assy cover 06L-140 with the screws 06L-160 and
the nuts 06L-170 to the angle 06L-150.
(n) Attach the studs 06L-220 and the washers 06L-210 to the oxygen container
assy cover 06L-140.
(p) Attach the support 06L-340 with the screws 06L-440 and the washers 06L-210
to the aft side wall assembly 06L-010.
1 Attach the special screws 06L-310 and the special washers 06L-330 to
the aft side wall assembly 06L-010.
2 Attach the handle assembly 06L-300 to the aft side wall assembly
06L-010.
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-410-040-D01
D2549026005200
(0) Installation of the Side Wall (06L-1)
(a) Attach the fittings 06L-020, 06L-030 with the screws 06L-040, 06L-050.
(b) Attach the toilet seat-cover dispenser 06L-460 with the screws 06L-470 to
the aft side wall assembly 06L-010.
1 Attach the plates 06L-260 with the screws 06L-240 to the post assembly
06L-230.
(d) Attach the post assembly 06L-230 with the screws 06L-270, 06L-290 and the
washers 06L-210.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06L-410 and to the pin 06L-400 and attach the emergency unlocking
device pivot 06L-390, the snap catch 06L-410 and the pin 06L-400 to the
emergency unlocking device housing 06L-370.
NOTE: Adjust the snap catch 06L-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
For Myanmar Airways (MMA) use only
06L-420 and attach the emergency unlocking device strike 06L-380 with
the bolt 06L-420 to the emergency unlocking device housing 06L-370.
(g) Attach the single door emergency unlocking device assembly 06L-360 with the
screws 06L-430 to the post assembly 06L-230.
(h) Attach the angle 06L-350 with the screws 06L-270 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(j) Attach the angles 06L-180 with the screws 06L-200 and the washers 06L-210
to the aft side wall assembly 06L-010.
(k) Attach the oxygen container assy 06L-190 with the screws 06L-200 and the
washers 06L-210 to the angles 06L-180.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06L-190.
(m) Attach the angle 06L-150 with the screws 06L-200 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(n) Attach the oxygen container assy cover 06L-140 with the screws 06L-160 and
the nuts 06L-170 to the angle 06L-150.
(p) Attach the studs 06L-220 and the washers 06L-210 to the oxygen container
assy cover 06L-140.
(q) Attach the support 06L-340 with the screws 06L-440 and the washers 06L-210
to the aft side wall assembly 06L-010.
1 Attach the special screws 06L-310 and the special washers 06L-330 to
the aft side wall assembly 06L-010.
2 Attach the handle assembly 06L-300 to the aft side wall assembly
06L-010.
SUBTASK 25-41-58-410-040-E01
(a) Attach the fittings 06L-020, 06L-030 with the screws 06L-040, 06L-050.
For Myanmar Airways (MMA) use only
(b) Attach the toilet seat-cover dispenser 06L-460 with the screws 06L-470 to
the aft side wall assembly 06L-010.
1 Attach the plates 06L-260 with the screws 06L-240 to the post assembly
06L-230.
(d) Attach the post assembly 06L-230 with the screws 06L-270, 06L-290, the
washers 06L-210 and the caps 06L-280.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06L-410 and to the pin 06L-400 and attach the emergency unlocking
device pivot 06L-390, the snap catch 06L-410 and the pin 06L-400 to the
emergency unlocking device housing 06L-370.
NOTE: Adjust the snap catch 06L-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06L-420 and attach the emergency unlocking device strike 06L-380 with
the bolt 06L-420 to the emergency unlocking device housing 06L-370.
(f) Attach the single door emergency unlocking device assembly 06L-360 with the
screws 06L-430 to the post assembly 06L-230.
(g) Attach the angle 06L-350 with the screws 06L-270 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(h) Attach the angles 06L-180 with the screws 06L-200 and the washers 06L-210
to the aft side wall assembly 06L-010.
(j) Attach the oxygen container assy 06L-190 with the screws 06L-200, 06L-205
and the washers 06L-210, 06L-215 to the angles 06L-180.
For Myanmar Airways (MMA) use only
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06L-190.
(l) Attach the angle 06L-150 with the screws 06L-200 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(m) Attach the oxygen container assy cover 06L-140 with the screws 06L-160 and
the nuts 06L-170 to the angle 06L-150.
(n) Attach the studs 06L-220 and the washers 06L-210 to the oxygen container
assy cover 06L-140.
(p) Attach the support 06L-340 with the screws 06L-440 and the washers 06L-210
to the aft side wall assembly 06L-010.
1 Attach the special screws 06L-310 and the special washers 06L-330 to
the aft side wall assembly 06L-010.
2 Attach the handle assembly 06L-300 to the aft side wall assembly
06L-010.
SUBTASK 25-41-58-410-040-F01
(a) Attach the fittings 06L-020, 06L-030 with the screws 06L-040, 06L-050.
(b) Attach the toilet seat-cover dispenser 06L-460 with the screws 06L-470 to
the aft side wall assembly 06L-010.
1 Attach the plates 06L-260 with the screws 06L-240 to the post assembly
06L-230.
(d) Attach the post assembly 06L-230 with the screws 06L-270, 06L-290, the
washers 06L-210 and the caps 06L-280.
For Myanmar Airways (MMA) use only
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06L-410 and to the pin 06L-400 and attach the emergency unlocking
device pivot 06L-390, the snap catch 06L-410 and the pin 06L-400 to the
emergency unlocking device housing 06L-370.
NOTE: Adjust the snap catch 06L-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06L-420 and attach the emergency unlocking device strike 06L-380 with
the bolt 06L-420 to the emergency unlocking device housing 06L-370.
(f) Attach the single door emergency unlocking device assembly 06L-360 with the
screws 06L-430 to the post assembly 06L-230.
(g) Attach the angle 06L-350 with the screws 06L-270 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(h) Attach the angles 06L-180 with the screws 06L-200 and the washers 06L-210
to the aft side wall assembly 06L-010.
(j) Attach the oxygen container assy 06L-190 with the screws 06L-200 and the
washers 06L-210 to the angles 06L-180.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06L-190.
(l) Attach the angle 06L-150 with the screws 06L-200 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(m) Attach the oxygen container assy cover 06L-140 with the screws 06L-160 and
the nuts 06L-170 to the angle 06L-150.
(n) Attach the studs 06L-220 and the washers 06L-210 to the oxygen container
For Myanmar Airways (MMA) use only
(p) Attach the support 06L-340 with the screws 06L-440 and the washers 06L-210
to the aft side wall assembly 06L-010.
1 Attach the special screws 06L-310 and the special washers 06L-330 to
the aft side wall assembly 06L-010.
2 Attach the handle assembly 06L-300 to the aft side wall assembly
06L-010.
SUBTASK 25-41-58-410-040-G01
(a) Attach the fittings 06L-020, 06L-030 with the screws 06L-040, 06L-050.
1 Attach the plates 06L-260 with the screws 06L-240 to the post assembly
06L-230.
(c) Attach the post assembly 06L-230 with the screws 06L-270, 06L-290, the
washers 06L-210 and the caps 06L-280.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06L-410 and to the pin 06L-400 and attach the emergency unlocking
device pivot 06L-390, the snap catch 06L-410 and the pin 06L-400 to the
emergency unlocking device housing 06L-370.
NOTE: Adjust the snap catch 06L-410 a half turn before stop.
For Myanmar Airways (MMA) use only
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06L-420 and attach the emergency unlocking device strike 06L-380 with
the bolt 06L-420 to the emergency unlocking device housing 06L-370.
(e) Attach the single door emergency unlocking device assembly 06L-360 with the
screws 06L-430 to the post assembly 06L-230.
(f) Attach the angle 06L-350 with the screws 06L-270 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(g) Attach the angles 06L-180 with the screws 06L-200 and the washers 06L-210
to the aft side wall assembly 06L-010.
(h) Attach the oxygen container assy 06L-190 with the screws 06L-200 and the
washers 06L-210 to the angles 06L-180.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06L-190.
(k) Attach the angle 06L-150 with the screws 06L-200 and the washers 06L-210 to
the aft side wall assembly 06L-010.
(l) Attach the oxygen container assy cover 06L-140 with the screws 06L-160 and
the nuts 06L-170 to the angle 06L-150.
(m) Attach the studs 06L-220 and the washers 06L-210 to the oxygen container
assy cover 06L-140.
(n) Attach the support 06L-340 with the screws 06L-440 and the washers 06L-210
to the aft side wall assembly 06L-010.
1 Attach the special screws 06L-310 and the special washers 06L-330 to
the aft side wall assembly 06L-010.
2 Attach the handle assembly 06L-300 to the aft side wall assembly
06L-010.
TASK 25-41-58-400-819-N01
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-041-A01
D2549020907400 D2549020908600
(1) Installation of the Side Wall (06M-1)
For Myanmar Airways (MMA) use only
(a) Attach the fittings 06M-020, 06M-030 with the screws 06M-040, 06M-050.
(b) Attach the coat hook 06M-450 with the screw 06M-351 to the aft side wall
assembly 06M-010.
(c) Attach the toilet seat-cover dispenser 06M-430 with the screws 06M-440 to
the aft side wall assembly 06M-010.
1 Attach the plates 06M-300 with the screws 06M-280 to the post assembly
06M-270.
(e) Attach the post assembly 06M-270 with the screws 06M-310, 06M-330, the
washers 06M-250 and the caps 06M-320.
(f) Assemble the single door emergency unlocking device assembly 06M-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06M-410 and to the pin 06M-400 and attach the emergency
unlocking device pivot 06M-390, the snap catch 06M-410 and the pin
06M-400 to the emergency unlocking device housing 06M-370.
NOTE: Adjust the snap catch 06M-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06M-420 and attach the emergency unlocking device strike 06M-380 with
the bolt 06M-420 to the emergency unlocking device housing 06M-370.
(g) Attach the single door emergency unlocking device assembly 06M-360 with the
screws 06M-350 to the post assembly 06M-270.
(h) Attach the angle 06M-340 with the screws 06M-310 and the washers 06M-250
to the aft side wall assembly 06M-010.
(j) Attach the angles 06M-220 with the screws 06M-240 and the washers 06M-250
to the aft side wall assembly 06M-010.
For Myanmar Airways (MMA) use only
(k) Attach the oxygen container assy 06M-230 with the screws 06M-240 and the
washers 06M-250 to the angles 06M-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06M-230.
(m) Attach the angle 06M-190 with the screws 06M-240 and the washers 06M-250
to the aft side wall assembly 06M-010.
(n) Attach the oxygen container assy cover 06M-180 with the screws 06M-200 and
the nuts 06M-210 to the angle 06M-190.
(p) Attach the studs 06M-260 and the washers 06M-250 to the oxygen container
assy cover 06M-180.
1 Attach the special screws 06M-150 and the special washers 06M-170 to
the aft side wall assembly 06M-010.
2 Attach the handle assemblies 06M-140 to the aft side wall assembly
06M-010.
SUBTASK 25-41-58-410-041-B01
D2549020907800 D2549020909400
(a) Attach the fittings 06M-020, 06M-030 with the screws 06M-040, 06M-050.
(b) Attach the toilet seat-cover dispenser 06M-430 with the screws 06M-440 to
the aft side wall assembly 06M-010.
1 Attach the plates 06M-300 with the screws 06M-280 to the post assembly
06M-270.
(d) Attach the post assembly 06M-270 with the screws 06M-310, 06M-330, the
washers 06M-250 and the caps 06M-320.
(e) Assemble the single door emergency unlocking device assembly 06M-360 as
For Myanmar Airways (MMA) use only
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06M-410 and to the pin 06M-400 and attach the emergency
unlocking device pivot 06M-390, the snap catch 06M-410 and the pin
06M-400 to the emergency unlocking device housing 06M-370.
NOTE: Adjust the snap catch 06M-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06M-420 and attach the emergency unlocking device strike 06M-380 with
the bolt 06M-420 to the emergency unlocking device housing 06M-370.
(f) Attach the single door emergency unlocking device assembly 06M-360 with the
screws 06M-350 to the post assembly 06M-270.
(g) Attach the angle 06M-340 with the screws 06M-310 and the washers 06M-250
to the aft side wall assembly 06M-010.
(h) Attach the angles 06M-220 with the screws 06M-240 and the washers 06M-250
to the aft side wall assembly 06M-010.
(j) Attach the oxygen container assy 06M-230 with the screws 06M-240 and the
washers 06M-250 to the angles 06M-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06M-230.
(l) Attach the angle 06M-190 with the screws 06M-240 and the washers 06M-250
to the aft side wall assembly 06M-010.
(m) Attach the oxygen container assy cover 06M-180 with the screws 06M-200 and
the nuts 06M-210 to the angle 06M-190.
(n) Attach the studs 06M-260 and the washers 06M-250 to the oxygen container
assy cover 06M-180.
1 Attach the special screws 06M-150 and the special washers 06M-170 to
the aft side wall assembly 06M-010.
2 Attach the handle assemblies 06M-140 to the aft side wall assembly
06M-010.
SUBTASK 25-41-58-410-041-C01
(a) Attach the fittings 06M-020, 06M-030 with the screws 06M-040, 06M-050.
1 Attach the plates 06M-300 with the screws 06M-280 to the post assembly
06M-270.
(c) Attach the post assembly 06M-270 with the screws 06M-310, 06M-330, the
washers 06M-250 and the caps 06M-320.
(d) Assemble the single door emergency unlocking device assembly 06M-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06M-410 and to the pin 06M-400 and attach the emergency
unlocking device pivot 06M-390, the snap catch 06M-410 and the pin
06M-400 to the emergency unlocking device housing 06M-370.
NOTE: Adjust the snap catch 06M-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
For Myanmar Airways (MMA) use only
06M-420 and attach the emergency unlocking device strike 06M-380 with
the bolt 06M-420 to the emergency unlocking device housing 06M-370.
(e) Attach the single door emergency unlocking device assembly 06M-360 with the
screws 06M-350 to the post assembly 06M-270.
(f) Attach the angle 06M-340 with the screws 06M-310 and the washers 06M-250
to the aft side wall assembly 06M-010.
(g) Attach the angles 06M-220 with the screws 06M-240 and the washers 06M-250
to the aft side wall assembly 06M-010.
(h) Attach the oxygen container assy 06M-230 with the screws 06M-240, 06M-245
and the washers 06M-250 to the angles 06M-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06M-230.
(k) Attach the angle 06M-190 with the screws 06M-240 and the washers 06M-250
to the aft side wall assembly 06M-010.
(l) Attach the oxygen container assy cover 06M-180 with the screws 06M-200 and
the nuts 06M-210 to the angle 06M-190.
(m) Attach the studs 06M-260 and the washers 06M-250 to the oxygen container
assy cover 06M-180.
1 Attach the special screws 06M-150 and the special washers 06M-170 to
the aft side wall assembly 06M-010.
2 Attach the handle assemblies 06M-140 to the aft side wall assembly
06M-010.
SUBTASK 25-41-58-410-041-D01
D2549010412800
(0) Installation of the Side Wall (06M-1)
(a) Attach the fittings 06M-020, 06M-030 with the screws 06M-040, 06M-050.
1 Attach the plates 06M-300 with the screws 06M-280 to the post assembly
06M-270.
(c) Attach the post assembly 06M-270 with the screws 06M-310, 06M-330, the
washers 06M-250 and the caps 06M-320.
(d) Assemble the single door emergency unlocking device assembly 06M-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06M-410 and to the pin 06M-400 and attach the emergency
unlocking device pivot 06M-390, the snap catch 06M-410 and the pin
06M-400 to the emergency unlocking device housing 06M-370.
NOTE: Adjust the snap catch 06M-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06M-420 and attach the emergency unlocking device strike 06M-380 with
the bolt 06M-420 to the emergency unlocking device housing 06M-370.
(e) Attach the single door emergency unlocking device assembly 06M-360 with the
screws 06M-350 to the post assembly 06M-270.
(f) Attach the angle 06M-340 with the screws 06M-310 and the washers 06M-250
to the aft side wall assembly 06M-010.
(g) Attach the angles 06M-220 with the screws 06M-240 and the washers 06M-250
to the aft side wall assembly 06M-010.
(h) Attach the oxygen container assy 06M-230 with the screws 06M-240 and the
washers 06M-250 to the angles 06M-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06M-230.
(k) Attach the angle 06M-190 with the screws 06M-240 and the washers 06M-250
For Myanmar Airways (MMA) use only
(l) Attach the oxygen container assy cover 06M-180 with the screws 06M-200 and
the nuts 06M-210 to the angle 06M-190.
(m) Attach the studs 06M-260 and the washers 06M-250 to the oxygen container
assy cover 06M-180.
1 Attach the special screws 06M-150 and the special washers 06M-170 to
the aft side wall assembly 06M-010.
2 Attach the handle assemblies 06M-140 to the aft side wall assembly
06M-010.
SUBTASK 25-41-58-410-041-E01
(a) Attach the fittings 06M-020, 06M-030 with the screws 06M-040, 06M-050.
1 Attach the plates 06M-300 with the screws 06M-280 to the post assembly
06M-270.
(c) Attach the post assembly 06M-270 with the screws 06M-310, 06M-330, the
washers 06M-250 and the caps 06M-320.
(d) Assemble the single door emergency unlocking device assembly 06M-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06M-410 and to the pin 06M-400 and attach the emergency
unlocking device pivot 06M-390, the snap catch 06M-410 and the pin
06M-400 to the emergency unlocking device housing 06M-370.
NOTE: Adjust the snap catch 06M-410 a half turn before stop.
For Myanmar Airways (MMA) use only
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06M-420 and attach the emergency unlocking device strike 06M-380 with
the bolt 06M-420 to the emergency unlocking device housing 06M-370.
(e) Attach the single door emergency unlocking device assembly 06M-360 with the
screws 06M-350 to the post assembly 06M-270.
(f) Attach the angle 06M-340 with the screws 06M-310 and the washers 06M-250
to the aft side wall assembly 06M-010.
(g) Attach the angles 06M-220 with the screws 06M-240 and the washers 06M-250
to the aft side wall assembly 06M-010.
(h) Attach the oxygen container assy 06M-230 with the screws 06M-240, 06M-245
and the washers 06M-250 to the angles 06M-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06M-230.
(k) Attach the angle 06M-190 with the screws 06M-240 and the washers 06M-250
to the aft side wall assembly 06M-010.
(l) Attach the oxygen container assy cover 06M-180 with the screws 06M-200 and
the nuts 06M-210 to the angle 06M-190.
(m) Attach the studs 06M-260 and the washers 06M-250 to the oxygen container
assy cover 06M-180.
1 Attach the special screws 06M-150 and the special washers 06M-170 to
the aft side wall assembly 06M-010.
2 Attach the handle assemblies 06M-140 to the aft side wall assembly
06M-010.
TASK 25-41-58-400-819-P01
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-042-A01
D2549040505800 R225401882-006
(1) Installation of the Side Wall (06N-1)
For Myanmar Airways (MMA) use only
(a) Attach the fittings 06N-020, 06N-030 with the screws 06N-040, 06N-050.
(b) Attach the coat hook 06N-450 with the screw 06N-351 to the aft side wall
assembly 06N-010.
(c) Attach the toilet seat-cover dispenser 06N-430 with the screws 06N-440 to
the aft side wall assembly 06N-010.
1 Attach the plates 06N-300 with the screws 06N-280 to the post assembly
06N-270.
(e) Attach the post assembly 06N-270 with the screws 06N-310, 06N-330 and
the washers 06N-250.
(g) Assemble the single door emergency unlocking device assembly 06N-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06N-410 and to the pin 06N-400 and attach the emergency
unlocking device pivot 06N-390, the snap catch 06N-410 and the pin
06N-400 to the emergency unlocking device housing 06N-370.
NOTE: Adjust the snap catch 06N-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06N-420 and attach the emergency unlocking device strike 06N-380 with
the bolt 06N-420 to the emergency unlocking device housing 06N-370.
(h) Attach the single door emergency unlocking device assembly 06N-360 with
the screws 06N-350 to the post assembly 06N-270.
For Myanmar Airways (MMA) use only
(j) Attach the angle 06N-340 with the screws 06N-310 and the washers 06N-250
to the aft side wall assembly 06N-010.
(k) Attach the angles 06N-220 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(l) Attach the oxygen container assy 06N-230 with the screws 06N-240, 06N-245
and the washers 06N-250 to the angles 06N-220.
(m) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06N-230.
(n) Attach the angle 06N-190 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(p) Attach the oxygen container assy cover 06N-180 with the screws 06N-200 and
the nuts 06N-210 to the angle 06N-190.
(q) Attach the studs 06N-260 and the washers 06N-250 to the oxygen container
assy cover 06N-180.
1 Attach the special screws 06N-150 and the special washers 06N-170 to
the aft side wall assembly 06N-010.
2 Attach the handle assemblies 06N-140 to the aft side wall assembly
06N-010.
SUBTASK 25-41-58-410-042-B01
(a) Attach the fittings 06N-020, 06N-030 with the screws 06N-040, 06N-050.
(b) Attach the coat hook 06N-450 with the screw 06N-351 to the aft side wall
assembly 06N-010.
(c) Attach the toilet seat-cover dispenser 06N-430 with the screws 06N-440 to
the aft side wall assembly 06N-010.
For Myanmar Airways (MMA) use only
1 Attach the plates 06N-300 with the screws 06N-280 to the post assembly
06N-270.
(e) Attach the post assembly 06N-270 with the screws 06N-310, 06N-330, the
washers 06N-250 and the caps 06N-320.
(f) Assemble the single door emergency unlocking device assembly 06N-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06N-410 and to the pin 06N-400 and attach the emergency
unlocking device pivot 06N-390, the snap catch 06N-410 and the pin
06N-400 to the emergency unlocking device housing 06N-370.
NOTE: Adjust the snap catch 06N-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06N-420 and attach the emergency unlocking device strike 06N-380 with
the bolt 06N-420 to the emergency unlocking device housing 06N-370.
(g) Attach the single door emergency unlocking device assembly 06N-360 with
the screws 06N-350 to the post assembly 06N-270.
(h) Attach the angle 06N-340 with the screws 06N-310 and the washers 06N-250
to the aft side wall assembly 06N-010.
(j) Attach the angles 06N-220 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(k) Attach the oxygen container assy 06N-230 with the screws 06N-240, 06N-245
and the washers 06N-250 to the angles 06N-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06N-230.
(m) Attach the angle 06N-190 with the screws 06N-240 and the washers 06N-250
For Myanmar Airways (MMA) use only
(n) Attach the oxygen container assy cover 06N-180 with the screws 06N-200 and
the nuts 06N-210 to the angle 06N-190.
(p) Attach the studs 06N-260 and the washers 06N-250 to the oxygen container
assy cover 06N-180.
1 Attach the special screws 06N-150 and the special washers 06N-170 to
the aft side wall assembly 06N-010.
2 Attach the handle assemblies 06N-140 to the aft side wall assembly
06N-010.
SUBTASK 25-41-58-410-042-C01
D2549030807400
(0) Installation of the Side Wall (06N-1)
(a) Attach the fittings 06N-020, 06N-030 with the screws 06N-040, 06N-050.
(b) Attach the coat hook 06N-450 with the screw 06N-351 to the aft side wall
assembly 06N-010.
(c) Attach the toilet seat-cover dispenser 06N-430 with the screws 06N-440 to
the aft side wall assembly 06N-010.
1 Attach the plates 06N-300 with the screws 06N-280 to the post assembly
06N-270.
(e) Attach the post assembly 06N-270 with the screws 06N-310, 06N-330, the
washers 06N-250 and the caps 06N-320.
(f) Assemble the single door emergency unlocking device assembly 06N-360 as
follows:
MANUFACTURER'S INSTRUCTIONS.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06N-410 and to the pin 06N-400 and attach the emergency
unlocking device pivot 06N-390, the snap catch 06N-410 and the pin
06N-400 to the emergency unlocking device housing 06N-370.
NOTE: Adjust the snap catch 06N-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06N-420 and attach the emergency unlocking device strike 06N-380 with
the bolt 06N-420 to the emergency unlocking device housing 06N-370.
(g) Attach the single door emergency unlocking device assembly 06N-360 with
the screws 06N-350 to the post assembly 06N-270.
(h) Attach the angle 06N-340 with the screws 06N-310 and the washers 06N-250
to the aft side wall assembly 06N-010.
(j) Attach the angles 06N-220 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(k) Attach the oxygen container assy 06N-230 with the screws 06N-240 and the
washers 06N-250 to the angles 06N-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06N-230.
(m) Attach the angle 06N-190 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(n) Attach the oxygen container assy cover 06N-180 with the screws 06N-200 and
the nuts 06N-210 to the angle 06N-190.
(p) Attach the studs 06N-260 and the washers 06N-250 to the oxygen container
assy cover 06N-180.
1 Attach the special screws 06N-150 and the special washers 06N-170 to
the aft side wall assembly 06N-010.
For Myanmar Airways (MMA) use only
2 Attach the handle assemblies 06N-140 to the aft side wall assembly
06N-010.
SUBTASK 25-41-58-410-042-D01
(b) Attach the fittings 06N-020, 06N-030 with the screws 06N-040, 06N-050.
(c) Attach the toilet seat-cover dispenser 06N-430 with the screws 06N-440 to
the aft side wall assembly 06N-010.
1 Attach the plates 06N-300 with the screws 06N-280 to the post assembly
06N-270.
(e) Attach the post assembly 06N-270 with the screws 06N-310, 06N-330, the
washers 06N-250 and the caps 06N-320.
(f) Assemble the single door emergency unlocking device assembly 06N-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06N-410 and to the pin 06N-400 and attach the emergency
unlocking device pivot 06N-390, the snap catch 06N-410 and the pin
06N-400 to the emergency unlocking device housing 06N-370.
NOTE: Adjust the snap catch 06N-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
For Myanmar Airways (MMA) use only
06N-420 and attach the emergency unlocking device strike 06N-380 with
the bolt 06N-420 to the emergency unlocking device housing 06N-370.
(g) Attach the single door emergency unlocking device assembly 06N-360 with
the screws 06N-350 to the post assembly 06N-270.
(h) Attach the angle 06N-340 with the screws 06N-310 and the washers 06N-250
to the aft side wall assembly 06N-010.
(j) Attach the angles 06N-220 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(k) Attach the oxygen container assy 06N-230 with the screws 06N-240 and the
washers 06N-250 to the angles 06N-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06N-230.
(m) Attach the angle 06N-190 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(n) Attach the oxygen container assy cover 06N-180 with the screws 06N-200 and
the nuts 06N-210 to the angle 06N-190.
(p) Attach the studs 06N-260 and the washers 06N-250 to the oxygen container
assy cover 06N-180.
1 Attach the special screws 06N-150 and the special washers 06N-170 to
the aft side wall assembly 06N-010.
2 Attach the handle assemblies 06N-140 to the aft side wall assembly
06N-010.
SUBTASK 25-41-58-410-042-E01
D2549030808400
(0) Installation of the Side Wall (06N-1)
(a) Attach the fittings 06N-020, 06N-030 with the screws 06N-040, 06N-050.
(b) Attach the toilet seat-cover dispenser 06N-430 with the screws 06N-440 to
For Myanmar Airways (MMA) use only
1 Attach the plates 06N-300 with the screws 06N-280 to the post assembly
06N-270.
(d) Attach the post assembly 06N-270 with the screws 06N-310, 06N-330, the
washers 06N-250 and the caps 06N-320.
(e) Assemble the single door emergency unlocking device assembly 06N-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06N-410 and to the pin 06N-400 and attach the emergency
unlocking device pivot 06N-390, the snap catch 06N-410 and the pin
06N-400 to the emergency unlocking device housing 06N-370.
NOTE: Adjust the snap catch 06N-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06N-420 and attach the emergency unlocking device strike 06N-380 with
the bolt 06N-420 to the emergency unlocking device housing 06N-370.
(f) Attach the single door emergency unlocking device assembly 06N-360 with
the screws 06N-350 to the post assembly 06N-270.
(g) Attach the angle 06N-340 with the screws 06N-310 and the washers 06N-250
to the aft side wall assembly 06N-010.
(h) Attach the angles 06N-220 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(j) Attach the oxygen container assy 06N-230 with the screws 06N-240 and the
washers 06N-250 to the angles 06N-220.
For Myanmar Airways (MMA) use only
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06N-230.
(l) Attach the angle 06N-190 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(m) Attach the oxygen container assy cover 06N-180 with the screws 06N-200 and
the nuts 06N-210 to the angle 06N-190.
(n) Attach the studs 06N-260 and the washers 06N-250 to the oxygen container
assy cover 06N-180.
1 Attach the special screws 06N-150 and the special washers 06N-170 to
the aft side wall assembly 06N-010.
2 Attach the handle assemblies 06N-140 to the aft side wall assembly
06N-010.
SUBTASK 25-41-58-410-042-F01
D2549020908000 D2549020911200
(0) Installation of the Side Wall (06N-1)
(a) Attach the fittings 06N-020, 06N-030 with the screws 06N-040, 06N-050.
(b) Attach the toilet seat-cover dispenser 06N-430 with the screws 06N-440 to
the aft side wall assembly 06N-010.
1 Attach the plates 06N-300 with the screws 06N-280 to the post assembly
06N-270.
(d) Attach the post assembly 06N-270 with the screws 06N-310, 06N-330, the
washers 06N-250 and the caps 06N-320.
(e) Assemble the single door emergency unlocking device assembly 06N-360 as
follows:
MANUFACTURER'S INSTRUCTIONS.
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06N-410 and to the pin 06N-400 and attach the emergency
unlocking device pivot 06N-390, the snap catch 06N-410 and the pin
06N-400 to the emergency unlocking device housing 06N-370.
NOTE: Adjust the snap catch 06N-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06N-420 and attach the emergency unlocking device strike 06N-380 with
the bolt 06N-420 to the emergency unlocking device housing 06N-370.
(f) Attach the single door emergency unlocking device assembly 06N-360 with
the screws 06N-350 to the post assembly 06N-270.
(g) Attach the angle 06N-340 with the screws 06N-310 and the washers 06N-250
to the aft side wall assembly 06N-010.
(h) Attach the angles 06N-220 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(j) Attach the oxygen container assy 06N-230 with the screws 06N-240 and the
washers 06N-250 to the angles 06N-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06N-230.
(l) Attach the angle 06N-190 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(m) Attach the oxygen container assy cover 06N-180 with the screws 06N-200 and
the nuts 06N-210 to the angle 06N-190.
(n) Attach the studs 06N-260 and the washers 06N-250 to the oxygen container
assy cover 06N-180.
1 Attach the special screws 06N-150 and the special washers 06N-170 to
the aft side wall assembly 06N-010.
For Myanmar Airways (MMA) use only
2 Attach the handle assemblies 06N-140 to the aft side wall assembly
06N-010.
SUBTASK 25-41-58-410-042-G01
(a) Attach the fittings 06N-020, 06N-030 with the screws 06N-040, 06N-050.
(b) Attach the toilet seat-cover dispenser 06N-430 with the screws 06N-440 to
the aft side wall assembly 06N-010.
1 Attach the plates 06N-300 with the screws 06N-280 to the post assembly
06N-270.
(d) Attach the post assembly 06N-270 with the screws 06N-310, 06N-330, the
washers 06N-250 and the caps 06N-320.
(e) Assemble the single door emergency unlocking device assembly 06N-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06N-410 and to the pin 06N-400 and attach the emergency
unlocking device pivot 06N-390, the snap catch 06N-410 and the pin
06N-400 to the emergency unlocking device housing 06N-370.
NOTE: Adjust the snap catch 06N-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
For Myanmar Airways (MMA) use only
06N-420 and attach the emergency unlocking device strike 06N-380 with
the bolt 06N-420 to the emergency unlocking device housing 06N-370.
(f) Attach the single door emergency unlocking device assembly 06N-360 with
the screws 06N-350 to the post assembly 06N-270.
(g) Attach the angle 06N-340 with the screws 06N-310 and the washers 06N-250
to the aft side wall assembly 06N-010.
(h) Attach the angles 06N-220 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(j) Attach the oxygen container assy 06N-230 with the screws 06N-240, 06N-245
and the washers 06N-250, 06N-255 to the angles 06N-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06N-230.
(l) Attach the angle 06N-190 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(m) Attach the oxygen container assy cover 06N-180 with the screws 06N-200 and
the nuts 06N-210 to the angle 06N-190.
(n) Attach the studs 06N-260 and the washers 06N-250 to the oxygen container
assy cover 06N-180.
1 Attach the special screws 06N-150 and the special washers 06N-170 to
the aft side wall assembly 06N-010.
2 Attach the handle assemblies 06N-140 to the aft side wall assembly
06N-010.
SUBTASK 25-41-58-410-042-H01
(a) Attach the fittings 06N-020, 06N-030 with the screws 06N-040, 06N-050.
1 Attach the plates 06N-300 with the screws 06N-280 to the post assembly
06N-270.
(c) Attach the post assembly 06N-270 with the screws 06N-310, 06N-330, the
washers 06N-250 and the caps 06N-320.
(d) Assemble the single door emergency unlocking device assembly 06N-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06N-410 and to the pin 06N-400 and attach the emergency
unlocking device pivot 06N-390, the snap catch 06N-410 and the pin
06N-400 to the emergency unlocking device housing 06N-370.
NOTE: Adjust the snap catch 06N-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06N-420 and attach the emergency unlocking device strike 06N-380 with
the bolt 06N-420 to the emergency unlocking device housing 06N-370.
(e) Attach the single door emergency unlocking device assembly 06N-360 with
the screws 06N-350 to the post assembly 06N-270.
(f) Attach the angle 06N-340 with the screws 06N-310 and the washers 06N-250
to the aft side wall assembly 06N-010.
(g) Attach the angles 06N-220 with the screws 06N-240 and the washers 06N-250
to the aft side wall assembly 06N-010.
(h) Attach the oxygen container assy 06N-230 with the screws 06N-240 and the
washers 06N-250 to the angles 06N-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06N-230.
(k) Attach the angle 06N-190 with the screws 06N-240 and the washers 06N-250
For Myanmar Airways (MMA) use only
(l) Attach the oxygen container assy cover 06N-180 with the screws 06N-200 and
the nuts 06N-210 to the angle 06N-190.
(m) Attach the studs 06N-260 and the washers 06N-250 to the oxygen container
assy cover 06N-180.
1 Attach the special screws 06N-150 and the special washers 06N-170 to
the aft side wall assembly 06N-010.
2 Attach the handle assemblies 06N-140 to the aft side wall assembly
06N-010.
TASK 25-41-58-400-819-Q01
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-043-A01
D2549020905600 D2549030809600
(1) Installation of the Side Wall (06P-1)
For Myanmar Airways (MMA) use only
(a) Attach the fittings 06P-020, 06P-030 with the screws 06P-040, 06P-050.
(b) Attach the coat hook 06P-450 with the screw 06P-351 to the aft side wall
assembly 06P-010.
(c) Attach the toilet seat-cover dispenser 06P-430 with the screws 06P-440 to
the aft side wall assembly 06P-010.
1 Attach the plates 06P-300 with the screws 06P-280 to the post assembly
06P-270.
(e) Attach the post assembly 06P-270 with the screws 06P-310, 06P-330, the
washers 06P-250 and the caps 06P-320.
(f) Assemble the single door emergency unlocking device assembly 06P-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06P-410 and to the pin 06P-400 and attach the emergency
unlocking device pivot 06P-390, the snap catch 06P-410 and the pin
06P-400 to the emergency unlocking device housing 06P-370.
NOTE: Adjust the snap catch 06P-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06P-420 and attach the emergency unlocking device strike 06P-380 with
the bolt 06P-420 to the emergency unlocking device housing 06P-370.
(g) Attach the single door emergency unlocking device assembly 06P-360 with the
screws 06P-350 to the post assembly 06P-270.
(h) Attach the angle 06P-340 with the screws 06P-310 and the washers 06P-250
to the aft side wall assembly 06P-010.
(j) Attach the angles 06P-220 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
For Myanmar Airways (MMA) use only
(k) Attach the oxygen container assy 06P-230 with the screws 06P-240 and the
washers 06P-250 to the angles 06P-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06P-230.
(m) Attach the angle 06P-190 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(n) Attach the oxygen container assy cover 06P-180 with the screws 06P-200 and
the nuts 06P-210 to the angle 06P-190.
(p) Attach the studs 06P-260 and the washers 06P-250 to the oxygen container
assy cover 06P-180.
1 Attach the special screws 06P-150 and the special washers 06P-170 to
the aft side wall assembly 06P-010.
2 Attach the handle assemblies 06P-140 to the aft side wall assembly
06P-010.
SUBTASK 25-41-58-410-043-B01
(a) Attach the fittings 06P-020, 06P-030 with the screws 06P-040, 06P-050.
(b) Attach the coat hook 06P-450 with the screw 06P-351 to the aft side wall
assembly 06P-010.
(c) Attach the toilet seat-cover dispenser 06P-430 with the screws 06P-440 to
the aft side wall assembly 06P-010.
1 Attach the plates 06P-300 with the screws 06P-280 to the post assembly
06P-270.
(e) Attach the post assembly 06P-270 with the screws 06P-310, 06P-330, the
For Myanmar Airways (MMA) use only
(f) Assemble the single door emergency unlocking device assembly 06P-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06P-410 and to the pin 06P-400 and attach the emergency
unlocking device pivot 06P-390, the snap catch 06P-410 and the pin
06P-400 to the emergency unlocking device housing 06P-370.
NOTE: Adjust the snap catch 06P-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06P-420 and attach the emergency unlocking device strike 06P-380 with
the bolt 06P-420 to the emergency unlocking device housing 06P-370.
(g) Attach the single door emergency unlocking device assembly 06P-360 with the
screws 06P-350 to the post assembly 06P-270.
(h) Attach the angle 06P-340 with the screws 06P-310 and the washers 06P-250
to the aft side wall assembly 06P-010.
(j) Attach the angles 06P-220 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(k) Attach the oxygen container assy 06P-230 with the screws 06P-240 and the
washers 06P-250 to the angles 06P-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06P-230.
(m) Attach the angle 06P-190 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(n) Attach the oxygen container assy cover 06P-180 with the screws 06P-200 and
the nuts 06P-210 to the angle 06P-190.
(p) Attach the studs 06P-260 and the washers 06P-250 to the oxygen container
For Myanmar Airways (MMA) use only
1 Attach the special screws 06P-150 and the special washers 06P-170 to
the aft side wall assembly 06P-010.
2 Attach the handle assemblies 06P-140 to the aft side wall assembly
06P-010.
SUBTASK 25-41-58-410-043-C01
(a) Attach the fittings 06P-020, 06P-030 with the screws 06P-040, 06P-050.
(b) Attach the coat hook 06P-450 with the screw 06P-351 to the aft side wall
assembly 06P-010.
1 Attach the plates 06P-300 with the screws 06P-280 to the post assembly
06P-270.
(d) Attach the post assembly 06P-270 with the screws 06P-310, 06P-330, the
washers 06P-250 and the caps 06P-320.
(f) Assemble the single door emergency unlocking device assembly 06P-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06P-410 and to the pin 06P-400 and attach the emergency
unlocking device pivot 06P-390, the snap catch 06P-410 and the pin
06P-400 to the emergency unlocking device housing 06P-370.
For Myanmar Airways (MMA) use only
NOTE: Adjust the snap catch 06P-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06P-420 and attach the emergency unlocking device strike 06P-380 with
the bolt 06P-420 to the emergency unlocking device housing 06P-370.
(g) Attach the single door emergency unlocking device assembly 06P-360 with the
screws 06P-350 to the post assembly 06P-270.
(h) Attach the angle 06P-340 with the screws 06P-310 and the washers 06P-250
to the aft side wall assembly 06P-010.
(j) Attach the angles 06P-220 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(k) Attach the oxygen container assy 06P-230 with the screws 06P-240, 06P-245
and the washers 06P-250 to the angles 06P-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06P-230.
(m) Attach the angle 06P-190 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(n) Attach the oxygen container assy cover 06P-180 with the screws 06P-200 and
the nuts 06P-210 to the angle 06P-190.
(p) Attach the studs 06P-260 and the washers 06P-250 to the oxygen container
assy cover 06P-180.
1 Attach the special screws 06P-150 and the special washers 06P-170 to
the aft side wall assembly 06P-010.
2 Attach the handle assemblies 06P-140 to the aft side wall assembly
06P-010.
SUBTASK 25-41-58-410-043-D01
D2549030809200
(0) Installation of the Side Wall (06P-1)
(a) Attach the fittings 06P-020, 06P-030 with the screws 06P-040, 06P-050.
(b) Attach the coat hook 06P-450 with the screw 06P-351 to the aft side wall
assembly 06P-010.
(c) Attach the toilet seat-cover dispenser 06P-430 with the screws 06P-440 to
the aft side wall assembly 06P-010.
1 Attach the plates 06P-300 with the screws 06P-280 to the post assembly
06P-270.
(e) Attach the post assembly 06P-270 with the screws 06P-310, 06P-330, the
washers 06P-250 and the caps 06P-320.
(g) Assemble the single door emergency unlocking device assembly 06P-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06P-410 and to the pin 06P-400 and attach the emergency
unlocking device pivot 06P-390, the snap catch 06P-410 and the pin
06P-400 to the emergency unlocking device housing 06P-370.
NOTE: Adjust the snap catch 06P-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
For Myanmar Airways (MMA) use only
06P-420 and attach the emergency unlocking device strike 06P-380 with
the bolt 06P-420 to the emergency unlocking device housing 06P-370.
(h) Attach the single door emergency unlocking device assembly 06P-360 with the
screws 06P-350 to the post assembly 06P-270.
(j) Attach the angle 06P-340 with the screws 06P-310 and the washers 06P-250
to the aft side wall assembly 06P-010.
(k) Attach the angles 06P-220 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(l) Attach the oxygen container assy 06P-230 with the screws 06P-240 and the
washers 06P-250 to the angles 06P-220.
(m) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06P-230.
(n) Attach the angle 06P-190 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(p) Attach the oxygen container assy cover 06P-180 with the screws 06P-200 and
the nuts 06P-210 to the angle 06P-190.
(q) Attach the studs 06P-260 and the washers 06P-250 to the oxygen container
assy cover 06P-180.
1 Attach the special screws 06P-150 and the special washers 06P-170 to
the aft side wall assembly 06P-010.
2 Attach the handle assemblies 06P-140 to the aft side wall assembly
06P-010.
SUBTASK 25-41-58-410-043-E01
(a) Attach the fittings 06P-020, 06P-030 with the screws 06P-040, 06P-050.
(b) Attach the toilet seat-cover dispenser 06P-430 with the screws 06P-440 to
For Myanmar Airways (MMA) use only
1 Attach the plates 06P-300 with the screws 06P-280 to the post assembly
06P-270.
(d) Attach the post assembly 06P-270 with the screws 06P-310, 06P-330, the
washers 06P-250 and the caps 06P-320.
(f) Assemble the single door emergency unlocking device assembly 06P-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06P-410 and to the pin 06P-400 and attach the emergency
unlocking device pivot 06P-390, the snap catch 06P-410 and the pin
06P-400 to the emergency unlocking device housing 06P-370.
NOTE: Adjust the snap catch 06P-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06P-420 and attach the emergency unlocking device strike 06P-380 with
the bolt 06P-420 to the emergency unlocking device housing 06P-370.
(g) Attach the single door emergency unlocking device assembly 06P-360 with the
screws 06P-350 to the post assembly 06P-270.
(h) Attach the angle 06P-340 with the screws 06P-310 and the washers 06P-250
to the aft side wall assembly 06P-010.
(j) Attach the angles 06P-220 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
For Myanmar Airways (MMA) use only
(k) Attach the oxygen container assy 06P-230 with the screws 06P-240 and the
washers 06P-250 to the angles 06P-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06P-230.
(m) Attach the angle 06P-190 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(n) Attach the oxygen container assy cover 06P-180 with the screws 06P-200 and
the nuts 06P-210 to the angle 06P-190.
(p) Attach the studs 06P-260 and the washers 06P-250 to the oxygen container
assy cover 06P-180.
1 Attach the special screws 06P-150 and the special washers 06P-170 to
the aft side wall assembly 06P-010.
2 Attach the handle assemblies 06P-140 to the aft side wall assembly
06P-010.
SUBTASK 25-41-58-410-043-F01
D2549020911000 D2549020913800
(a) Attach the fittings 06P-020, 06P-030 with the screws 06P-040, 06P-050.
(b) Attach the toilet seat-cover dispenser 06P-430 with the screws 06P-440 to
the aft side wall assembly 06P-010.
1 Attach the plates 06P-300 with the screws 06P-280 to the post assembly
06P-270.
(d) Attach the post assembly 06P-270 with the screws 06P-310, 06P-330, the
washers 06P-250 and the caps 06P-320.
(f) Assemble the single door emergency unlocking device assembly 06P-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06P-410 and to the pin 06P-400 and attach the emergency
unlocking device pivot 06P-390, the snap catch 06P-410 and the pin
06P-400 to the emergency unlocking device housing 06P-370.
NOTE: Adjust the snap catch 06P-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06P-420 and attach the emergency unlocking device strike 06P-380 with
the bolt 06P-420 to the emergency unlocking device housing 06P-370.
(g) Attach the single door emergency unlocking device assembly 06P-360 with the
screws 06P-350 to the post assembly 06P-270.
(h) Attach the angle 06P-340 with the screws 06P-310 and the washers 06P-250
to the aft side wall assembly 06P-010.
(j) Attach the angles 06P-220 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(k) Attach the oxygen container assy 06P-230 with the screws 06P-240 and the
washers 06P-250 to the angles 06P-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06P-230.
(m) Attach the angle 06P-190 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(n) Attach the oxygen container assy cover 06P-180 with the screws 06P-200 and
For Myanmar Airways (MMA) use only
(p) Attach the studs 06P-260 and the washers 06P-250 to the oxygen container
assy cover 06P-180.
1 Attach the special screws 06P-150 and the special washers 06P-170 to
the aft side wall assembly 06P-010.
2 Attach the handle assemblies 06P-140 to the aft side wall assembly
06P-010.
SUBTASK 25-41-58-410-043-G01
(a) Attach the fittings 06P-020, 06P-030 with the screws 06P-040, 06P-050.
(b) Attach the toilet seat-cover dispenser 06P-430 with the screws 06P-440 to
the aft side wall assembly 06P-010.
1 Attach the plates 06P-300 with the screws 06P-280 to the post assembly
06P-270.
(d) Attach the post assembly 06P-270 with the screws 06P-310, 06P-330, the
washers 06P-250 and the caps 06P-320.
(e) Assemble the single door emergency unlocking device assembly 06P-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06P-410 and to the pin 06P-400 and attach the emergency
unlocking device pivot 06P-390, the snap catch 06P-410 and the pin
06P-400 to the emergency unlocking device housing 06P-370.
NOTE: Adjust the snap catch 06P-410 a half turn before stop.
For Myanmar Airways (MMA) use only
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06P-420 and attach the emergency unlocking device strike 06P-380 with
the bolt 06P-420 to the emergency unlocking device housing 06P-370.
(f) Attach the single door emergency unlocking device assembly 06P-360 with the
screws 06P-350 to the post assembly 06P-270.
(g) Attach the angle 06P-340 with the screws 06P-310 and the washers 06P-250
to the aft side wall assembly 06P-010.
(h) Attach the angles 06P-220 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(j) Attach the oxygen container assy 06P-230 with the screws 06P-240 and the
washers 06P-250 to the angles 06P-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06P-230.
(l) Attach the angle 06P-190 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(m) Attach the oxygen container assy cover 06P-180 with the screws 06P-200 and
the nuts 06P-210 to the angle 06P-190.
(n) Attach the studs 06P-260 and the washers 06P-250 to the oxygen container
assy cover 06P-180.
1 Attach the special screws 06P-150 and the special washers 06P-170 to
the aft side wall assembly 06P-010.
2 Attach the handle assemblies 06P-140 to the aft side wall assembly
06P-010.
SUBTASK 25-41-58-410-043-H01
(a) Attach the fittings 06P-020, 06P-030 with the screws 06P-040, 06P-050.
1 Attach the plates 06P-300 with the screws 06P-280 to the post assembly
06P-270.
(c) Attach the post assembly 06P-270 with the screws 06P-310, 06P-330, the
washers 06P-250 and the caps 06P-320.
(d) Assemble the single door emergency unlocking device assembly 06P-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06P-410 and to the pin 06P-400 and attach the emergency
unlocking device pivot 06P-390, the snap catch 06P-410 and the pin
06P-400 to the emergency unlocking device housing 06P-370.
NOTE: Adjust the snap catch 06P-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06P-420 and attach the emergency unlocking device strike 06P-380 with
the bolt 06P-420 to the emergency unlocking device housing 06P-370.
(e) Attach the single door emergency unlocking device assembly 06P-360 with the
screws 06P-350 to the post assembly 06P-270.
(f) Attach the angle 06P-340 with the screws 06P-310 and the washers 06P-250
to the aft side wall assembly 06P-010.
(g) Attach the angles 06P-220 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(h) Attach the oxygen container assy 06P-230 with the screws 06P-240 and the
washers 06P-250 to the angles 06P-220.
For Myanmar Airways (MMA) use only
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06P-230.
(k) Attach the angle 06P-190 with the screws 06P-240 and the washers 06P-250
to the aft side wall assembly 06P-010.
(l) Attach the oxygen container assy cover 06P-180 with the screws 06P-200 and
the nuts 06P-210 to the angle 06P-190.
(m) Attach the studs 06P-260 and the washers 06P-250 to the oxygen container
assy cover 06P-180.
1 Attach the special screws 06P-150 and the special washers 06P-170 to
the aft side wall assembly 06P-010.
2 Attach the handle assemblies 06P-140 to the aft side wall assembly
06P-010.
TASK 25-41-58-400-819-R01
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-044-A01
D2549010414200
(1) Installation of the Side Wall (06Q-1)
For Myanmar Airways (MMA) use only
(a) Attach the fittings 06Q-020, 06Q-030 with the screws 06Q-040, 06Q-050.
(b) Attach the toilet seat-cover dispenser 06Q-460 with the screws 06Q-470 to
the aft side wall assembly 06Q-010.
1 Attach the plates 06Q-260 with the screws 06Q-240 to the post assembly
06Q-230.
(d) Attach the post assembly 06Q-230 with the screws 06Q-270, 06Q-450 and
the washers 06Q-210.
(f) Assemble the single door emergency unlocking device assembly 06Q-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06Q-410 and to the pin 06Q-400 and attach the emergency
unlocking device pivot 06Q-390, the snap catch 06Q-410 and the pin
NOTE: Adjust the snap catch 06Q-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06Q-420 and attach the emergency unlocking device strike 06Q-380 with
the bolt 06Q-420 to the emergency unlocking device housing 06Q-370.
(g) Attach the single door emergency unlocking device assembly 06Q-360 with
the screws 06Q-430 to the post assembly 06Q-230.
(h) Attach the angle 06Q-350 with the screws 06Q-270 and the washers 06Q-210
For Myanmar Airways (MMA) use only
(j) Attach the angles 06Q-180 with the screws 06Q-200 and the washers 06Q-210
to the aft side wall assembly 06Q-010.
(k) Attach the oxygen container assy 06Q-190 with the screws 06Q-200 and the
washers 06Q-210 to the angles 06Q-180.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06Q-190.
(m) Attach the angle 06Q-150 with the screws 06Q-200 and the washers 06Q-210
to the aft side wall assembly 06Q-010.
(n) Attach the oxygen container assy cover 06Q-140 with the screws 06Q-160 and
the nuts 06Q-170 to the angle 06Q-150.
(p) Attach the studs 06Q-220 and the washers 06Q-210 to the oxygen container
assy cover 06Q-140.
(q) Attach the support 06Q-340 with the screws 06Q-440 and the washers
06Q-210 to the aft side wall assembly 06Q-010.
1 Attach the special screws 06Q-310 and the special washers 06Q-330 to
the aft side wall assembly 06Q-010.
2 Attach the handle assembly 06Q-300 to the aft side wall assembly
06Q-010.
SUBTASK 25-41-58-410-044-B01
(a) Attach the fittings 06Q-020, 06Q-030 with the screws 06Q-040, 06Q-050.
(b) Attach the toilet seat-cover dispenser 06Q-460 with the screws 06Q-470 to
the aft side wall assembly 06Q-010.
For Myanmar Airways (MMA) use only
1 Attach the plates 06Q-260 with the screws 06Q-240 to the post assembly
06Q-230.
(d) Attach the post assembly 06Q-230 with the screws 06Q-270, 06Q-450 and
the washers 06Q-210.
(f) Assemble the single door emergency unlocking device assembly 06Q-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06Q-410 and to the pin 06Q-400 and attach the emergency
unlocking device pivot 06Q-390, the snap catch 06Q-410 and the pin
06Q-400 to the emergency unlocking device housing 06Q-370.
NOTE: Adjust the snap catch 06Q-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06Q-420 and attach the emergency unlocking device strike 06Q-380 with
the bolt 06Q-420 to the emergency unlocking device housing 06Q-370.
(g) Attach the single door emergency unlocking device assembly 06Q-360 with
the screws 06Q-430 to the post assembly 06Q-230.
(h) Attach the angle 06Q-350 with the screws 06Q-270 and the washers 06Q-210
to the aft side wall assembly 06Q-010.
(j) Attach the angles 06Q-180 with the screws 06Q-200 and the washers 06Q-210
to the aft side wall assembly 06Q-010.
For Myanmar Airways (MMA) use only
(k) Attach the oxygen container assy 06Q-190 with the screws 06Q-200, 06Q-205
and the washers 06Q-210, 06Q-215 to the angles 06Q-180.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06Q-190.
(m) Attach the angle 06Q-150 with the screws 06Q-200 and the washers 06Q-210
to the aft side wall assembly 06Q-010.
(n) Attach the oxygen container assy cover 06Q-140 with the screws 06Q-160 and
the nuts 06Q-170 to the angle 06Q-150.
(p) Attach the studs 06Q-220 and the washers 06Q-210 to the oxygen container
assy cover 06Q-140.
(q) Attach the support 06Q-340 with the screws 06Q-440 and the washers
06Q-210 to the aft side wall assembly 06Q-010.
1 Attach the special screws 06Q-310 and the special washers 06Q-330 to
the aft side wall assembly 06Q-010.
2 Attach the handle assembly 06Q-300 to the aft side wall assembly
06Q-010.
SUBTASK 25-41-58-410-044-C01
D2549010300000
(0) Installation of the Side Wall (06Q-1)
(a) Attach the fittings 06Q-020, 06Q-030 with the screws 06Q-040, 06Q-050.
(b) Attach the toilet seat-cover dispenser 06Q-460 with the screws 06Q-470 to
the aft side wall assembly 06Q-010.
1 Attach the plates 06Q-260 with the screws 06Q-240 to the post assembly
06Q-230.
For Myanmar Airways (MMA) use only
(d) Attach the post assembly 06Q-230 with the screws 06Q-270, 06Q-450 and
the washers 06Q-210.
(f) Assemble the single door emergency unlocking device assembly 06Q-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06Q-410 and to the pin 06Q-400 and attach the emergency
unlocking device pivot 06Q-390, the snap catch 06Q-410 and the pin
06Q-400 to the emergency unlocking device housing 06Q-370.
NOTE: Adjust the snap catch 06Q-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06Q-420 and attach the emergency unlocking device strike 06Q-380 with
the bolt 06Q-420 to the emergency unlocking device housing 06Q-370.
(g) Attach the single door emergency unlocking device assembly 06Q-360 with
the screws 06Q-430 to the post assembly 06Q-230.
(h) Attach the angle 06Q-350 with the screws 06Q-270 and the washers 06Q-210
to the aft side wall assembly 06Q-010.
(j) Attach the angles 06Q-180 with the screws 06Q-200 and the washers 06Q-210
to the aft side wall assembly 06Q-010.
(k) Attach the oxygen container assy 06Q-190 with the screws 06Q-200 and the
washers 06Q-210 to the angles 06Q-180.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06Q-190.
(m) Attach the angle 06Q-150 with the screws 06Q-200 and the washers 06Q-210
For Myanmar Airways (MMA) use only
(n) Attach the oxygen container assy cover 06Q-140 with the screws 06Q-160 and
the nuts 06Q-170 to the angle 06Q-150.
(p) Attach the studs 06Q-220 and the washers 06Q-210 to the oxygen container
assy cover 06Q-140.
(q) Attach the support 06Q-340 with the screws 06Q-440 and the washers
06Q-210 to the aft side wall assembly 06Q-010.
1 Attach the special screws 06Q-310 and the special washers 06Q-330 to
the aft side wall assembly 06Q-010.
2 Attach the handle assembly 06Q-300 to the aft side wall assembly
06Q-010.
SUBTASK 25-41-58-410-044-E01
(a) Attach the fittings 06Q-020, 06Q-030 with the screws 06Q-040, 06Q-050.
1 Attach the plates 06Q-260 with the screws 06Q-240 to the post assembly
06Q-230.
(c) Attach the post assembly 06Q-230 with the screws 06Q-270, 06Q-450 and
the washers 06Q-210.
(e) Assemble the single door emergency unlocking device assembly 06Q-360 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06Q-410 and to the pin 06Q-400 and attach the emergency
unlocking device pivot 06Q-390, the snap catch 06Q-410 and the pin
06Q-400 to the emergency unlocking device housing 06Q-370.
NOTE: Adjust the snap catch 06Q-410 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06Q-420 and attach the emergency unlocking device strike 06Q-380 with
the bolt 06Q-420 to the emergency unlocking device housing 06Q-370.
(f) Attach the single door emergency unlocking device assembly 06Q-360 with
the screws 06Q-430 to the post assembly 06Q-230.
(g) Attach the angle 06Q-350 with the screws 06Q-270 and the washers 06Q-210
to the aft side wall assembly 06Q-010.
(h) Attach the angles 06Q-180 with the screws 06Q-200 and the washers 06Q-210
to the aft side wall assembly 06Q-010.
(j) Attach the oxygen container assy 06Q-190 with the screws 06Q-200 and the
washers 06Q-210 to the angles 06Q-180.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06Q-190.
(l) Attach the angle 06Q-150 with the screws 06Q-200 and the washers 06Q-210
to the aft side wall assembly 06Q-010.
(m) Attach the oxygen container assy cover 06Q-140 with the screws 06Q-160 and
the nuts 06Q-170 to the angle 06Q-150.
(n) Attach the studs 06Q-220 and the washers 06Q-210 to the oxygen container
assy cover 06Q-140.
(p) Attach the support 06Q-340 with the screws 06Q-440 and the washers
06Q-210 to the aft side wall assembly 06Q-010.
1 Attach the special screws 06Q-310 and the special washers 06Q-330 to
the aft side wall assembly 06Q-010.
2 Attach the handle assembly 06Q-300 to the aft side wall assembly
06Q-010.
TASK 25-41-58-400-819-S01
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
For Myanmar Airways (MMA) use only
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-045-A01
D2549030809400
(1) Installation of the Side Wall (06R-1)
(a) Attach the fittings 06R-020, 06R-030 with the screws 06R-040, 06R-050.
1 Attach the plates 06R-330 with the screws 06R-310 to the post assembly
For Myanmar Airways (MMA) use only
06R-300.
(c) Attach the post assembly 06R-300 with the screws 06R-340, 06R-370 and
the washers 06R-280.
(e) Assemble the single door emergency unlocking device assembly 06R-400 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06R-450 and to the pin 06R-440 and attach the emergency
unlocking device pivot 06R-430, the snap catch 06R-450 and the pin
06R-440 to the emergency unlocking device housing 06R-410.
NOTE: Adjust the snap catch 06R-450 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06R-460 and attach the emergency unlocking device strike 06R-420 with
(f) Attach the single door emergency unlocking device assembly 06R-400 with
the screws 06R-390 to the post assembly 06R-300.
(g) Attach the angle 06R-380 with the screws 06R-340 and the washers 06R-280
to the aft side wall assembly 06R-010.
(h) Attach the angles 06R-250 with the screws 06R-270 and the washers 06R-280
to the aft side wall assembly 06R-010.
(j) Attach the oxygen container assy 06R-260 with the screws 06R-270 and the
washers 06R-280 to the angles 06R-250.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06R-260.
For Myanmar Airways (MMA) use only
(l) Attach the angle 06R-220 with the screws 06R-270 and the washers 06R-280
to the aft side wall assembly 06R-010.
(m) Attach the oxygen container assy cover 06R-210 with the screws 06R-230 and
the nuts 06R-240 to the angle 06R-220.
(n) Attach the studs 06R-290 and the washers 06R-280 to the oxygen container
assy cover 06R-210.
1 (a) Attach the handrails 06R-150, 06R-160 with the fastening bolts
06R-200. the fastener assemblies 06R-180 and the bolt bushings
06R-190 to the aft side wall assembly 06R-010.
SUBTASK 25-41-58-410-045-B01
(a) Attach the fittings 06R-020, 06R-030 with the screws 06R-040, 06R-050.
1 Attach the plates 06R-330 with the screws 06R-310 to the post assembly
06R-300.
(c) Attach the post assembly 06R-300 with the screws 06R-340, 06R-370 and
the washers 06R-280.
(e) Assemble the single door emergency unlocking device assembly 06R-400 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06R-450 and to the pin 06R-440 and attach the emergency
unlocking device pivot 06R-430, the snap catch 06R-450 and the pin
06R-440 to the emergency unlocking device housing 06R-410.
NOTE: Adjust the snap catch 06R-450 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06R-460 and attach the emergency unlocking device strike 06R-420 with
the bolt 06R-460 to the emergency unlocking device housing 06R-410.
(f) Attach the single door emergency unlocking device assembly 06R-400 with
the screws 06R-390 to the post assembly 06R-300.
(g) Attach the angle 06R-380 with the screws 06R-340 and the washers 06R-280
to the aft side wall assembly 06R-010.
(h) Attach the angles 06R-250 with the screws 06R-270 and the washers 06R-280
to the aft side wall assembly 06R-010.
(j) Attach the oxygen container assy 06R-260 with the screws 06R-270 and the
washers 06R-280 to the angles 06R-250.
(k) Attach the oxygen container assy 06R-260 with the screws 06R-270, 06R-275
and the washers 06R-280 to the angles 06R-250.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06R-260.
(m) Attach the angle 06R-220 with the screws 06R-270 and the washers 06R-280
to the aft side wall assembly 06R-010.
(n) Attach the oxygen container assy cover 06R-210 with the screws 06R-230 and
the nuts 06R-240 to the angle 06R-220.
(p) Attach the studs 06R-290 and the washers 06R-280 to the oxygen container
assy cover 06R-210.
1 Attach the special screws 06R-480 and the special washers 06R-500 to
the aft side wall assembly 06R-010.
2 Attach the handle assemblies 06R-470 to the aft side wall assembly
06R-010.
SUBTASK 25-41-58-410-045-C01
D2549010301000 D2549026002600
(0) Installation of the Side Wall (06R-1)
(a) Attach the fittings 06R-020, 06R-030 with the screws 06R-040, 06R-050.
1 Attach the plates 06R-330 with the screws 06R-310 to the post assembly
06R-300.
(c) Attach the post assembly 06R-300 with the screws 06R-340, 06R-370 and
the washers 06R-280.
(e) Assemble the single door emergency unlocking device assembly 06R-400 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06R-450 and to the pin 06R-440 and attach the emergency
unlocking device pivot 06R-430, the snap catch 06R-450 and the pin
06R-440 to the emergency unlocking device housing 06R-410.
NOTE: Adjust the snap catch 06R-450 a half turn before stop.
MANUFACTURER'S INSTRUCTIONS.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06R-460 and attach the emergency unlocking device strike 06R-420 with
the bolt 06R-460 to the emergency unlocking device housing 06R-410.
(f) Attach the single door emergency unlocking device assembly 06R-400 with
the screws 06R-390 to the post assembly 06R-300.
(g) Attach the angle 06R-380 with the screws 06R-340 and the washers 06R-280
to the aft side wall assembly 06R-010.
(h) Attach the angles 06R-250 with the screws 06R-270 and the washers 06R-280
to the aft side wall assembly 06R-010.
(j) Attach the oxygen container assy 06R-260 with the screws 06R-270 and the
washers 06R-280 to the angles 06R-250.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06R-260.
(l) Attach the angle 06R-220 with the screws 06R-270 and the washers 06R-280
to the aft side wall assembly 06R-010.
(m) Attach the oxygen container assy cover 06R-210 with the screws 06R-230 and
the nuts 06R-240 to the angle 06R-220.
(n) Attach the studs 06R-290 and the washers 06R-280 to the oxygen container
assy cover 06R-210.
1 Attach the special screws 06R-480 and the special washers 06R-500 to
the aft side wall assembly 06R-010.
2 Attach the handle assemblies 06R-470 to the aft side wall assembly
06R-010.
TASK 25-41-58-400-819-T01
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
For Myanmar Airways (MMA) use only
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-046-A01
D2549020910800
(1) Installation of the Side Wall (06S-1)
(a) Attach the fittings 06S-020, 06S-030 with the screws 06S-040, 06S-050.
1 Attach the plates 06S-300 with the screws 06S-280 to the post assembly
For Myanmar Airways (MMA) use only
06S-270.
(c) Attach the post assembly 06S-270 with the screws 06S-310, 06S-340, the
washers 06S-250 and the caps 06S-470.
(d) Assemble the single door emergency unlocking device assembly 06S-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06S-420 and to the pin 06S-410 and attach the emergency
unlocking device pivot 06S-400, the snap catch 06S-420 and the pin
06S-410 to the emergency unlocking device housing 06S-380.
NOTE: Adjust the snap catch 06S-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06S-430 and attach the emergency unlocking device strike 06S-390 with
the bolt 06S-430 to the emergency unlocking device housing 06S-380.
(e) Attach the single door emergency unlocking device assembly 06S-370 with the
screws 06S-360 to the post assembly 06S-270.
(f) Attach the angle 06S-350 with the screws 06S-310 and the washers 06S-250
to the aft side wall assembly 06S-010.
(g) Attach the angles 06S-220 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(h) Attach the oxygen container assy 06S-230 with the screws 06S-240 and the
washers 06S-250 to the angles 06S-220.
(j) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06S-230.
(k) Attach the angle 06S-190 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(l) Attach the oxygen container assy cover 06S-180 with the screws 06S-200 and
For Myanmar Airways (MMA) use only
(m) Attach the studs 06S-260 and the washers 06S-250 to the oxygen container
assy cover 06S-180.
1 Attach the special screws 06S-150 and the special washers 06S-170 to
the aft side wall assembly 06S-010.
2 Attach the handle assemblies 06S-140 to the aft side wall assembly
06S-010.
SUBTASK 25-41-58-410-046-B01
D2549026004000 D2549030811400
(0) Installation of the Side Wall (06S-1)
(a) Attach the fittings 06S-020, 06S-030 with the screws 06S-040, 06S-050.
(b) Attach the coat hook 06S-460 with the screw 06S-361 to the aft side wall
assembly 06S-010.
(c) Attach the toilet seat-cover dispenser 06S-440 with the screws 06S-450 to
the aft side wall assembly 06S-010.
1 Attach the plates 06S-300 with the screws 06S-280 to the post assembly
06S-270.
(e) Attach the post assembly 06S-270 with the screws 06S-310, 06S-340 and
the washers 06S-250.
(g) Assemble the single door emergency unlocking device assembly 06S-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06S-420 and to the pin 06S-410 and attach the emergency
unlocking device pivot 06S-400, the snap catch 06S-420 and the pin
06S-410 to the emergency unlocking device housing 06S-380.
NOTE: Adjust the snap catch 06S-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06S-430 and attach the emergency unlocking device strike 06S-390 with
the bolt 06S-430 to the emergency unlocking device housing 06S-380.
(h) Attach the single door emergency unlocking device assembly 06S-370 with the
screws 06S-360 to the post assembly 06S-270.
(j) Attach the angle 06S-350 with the screws 06S-310 and the washers 06S-250
to the aft side wall assembly 06S-010.
(k) Attach the angles 06S-220 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(l) Attach the oxygen container assy 06S-230 with the screws 06S-240 and the
washers 06S-250 to the angles 06S-220.
(m) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06S-230.
(n) Attach the angle 06S-190 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(p) Attach the oxygen container assy cover 06S-180 with the screws 06S-200 and
the nuts 06S-210 to the angle 06S-190.
(q) Attach the studs 06S-260 and the washers 06S-250 to the oxygen container
assy cover 06S-180.
1 Attach the special screws 06S-150 and the special washers 06S-170 to
the aft side wall assembly 06S-010.
For Myanmar Airways (MMA) use only
2 Attach the handle assemblies 06S-140 to the aft side wall assembly
06S-010.
SUBTASK 25-41-58-410-046-C01
D2549020913600
(0) Installation of the Side Wall (06S-1)
(a) Attach the fittings 06S-020, 06S-030 with the screws 06S-040, 06S-050.
(b) Attach the coat hook 06S-460 with the screw 06S-361 to the aft side wall
assembly 06S-010.
(c) Attach the toilet seat-cover dispenser 06S-440 with the screws 06S-450 to
the aft side wall assembly 06S-010.
1 Attach the plates 06S-300 with the screws 06S-280 to the post assembly
06S-270.
(e) Attach the post assembly 06S-270 with the screws 06S-310, 06S-340 and
the washers 06S-250.
(g) Assemble the single door emergency unlocking device assembly 06S-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06S-420 and to the pin 06S-410 and attach the emergency
unlocking device pivot 06S-400, the snap catch 06S-420 and the pin
06S-410 to the emergency unlocking device housing 06S-380.
NOTE: Adjust the snap catch 06S-420 a half turn before stop.
For Myanmar Airways (MMA) use only
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06S-430 and attach the emergency unlocking device strike 06S-390 with
the bolt 06S-430 to the emergency unlocking device housing 06S-380.
(h) Attach the single door emergency unlocking device assembly 06S-370 with the
screws 06S-360 to the post assembly 06S-270.
(j) Attach the angle 06S-350 with the screws 06S-310 and the washers 06S-250
to the aft side wall assembly 06S-010.
(k) Attach the angles 06S-220 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(l) Attach the oxygen container assy 06S-230 with the screws 06S-240 and the
washers 06S-250 to the angles 06S-220.
(m) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06S-230.
(n) Attach the angle 06S-190 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(p) Attach the oxygen container assy cover 06S-180 with the screws 06S-200 and
the nuts 06S-210 to the angle 06S-190.
(q) Attach the studs 06S-260 and the washers 06S-250 to the oxygen container
assy cover 06S-180.
1 Attach the special screws 06S-150 and the special washers 06S-170 to
the aft side wall assembly 06S-010.
2 Attach the handle assemblies 06S-140 to the aft side wall assembly
06S-010.
SUBTASK 25-41-58-410-046-D01
D2549020914000
For Myanmar Airways (MMA) use only
(a) Attach the fittings 06S-020, 06S-030 with the screws 06S-040, 06S-050.
(b) Attach the toilet seat-cover dispenser 06S-440 with the screws 06S-450 to
the aft side wall assembly 06S-010.
1 Attach the plates 06S-300 with the screws 06S-280 to the post assembly
06S-270.
(d) Attach the post assembly 06S-270 with the screws 06S-310, 06S-340 and
the washers 06S-250.
(f) Assemble the single door emergency unlocking device assembly 06S-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06S-420 and to the pin 06S-410 and attach the emergency
unlocking device pivot 06S-400, the snap catch 06S-420 and the pin
NOTE: Adjust the snap catch 06S-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06S-430 and attach the emergency unlocking device strike 06S-390 with
the bolt 06S-430 to the emergency unlocking device housing 06S-380.
(g) Attach the single door emergency unlocking device assembly 06S-370 with the
screws 06S-360 to the post assembly 06S-270.
(h) Attach the angle 06S-350 with the screws 06S-310 and the washers 06S-250
For Myanmar Airways (MMA) use only
(j) Attach the angles 06S-220 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(k) Attach the oxygen container assy 06S-230 with the screws 06S-240 and the
washers 06S-250 to the angles 06S-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06S-230.
(m) Attach the angle 06S-190 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(n) Attach the oxygen container assy cover 06S-180 with the screws 06S-200 and
the nuts 06S-210 to the angle 06S-190.
(p) Attach the studs 06S-260 and the washers 06S-250 to the oxygen container
assy cover 06S-180.
1 Attach the special screws 06S-150 and the special washers 06S-170 to
the aft side wall assembly 06S-010.
2 Attach the handle assemblies 06S-140 to the aft side wall assembly
06S-010.
SUBTASK 25-41-58-410-046-E01
(a) Attach the fittings 06S-020, 06S-030 with the screws 06S-040, 06S-050.
(b) Attach the toilet seat-cover dispenser 06S-440 with the screws 06S-450 to
the aft side wall assembly 06S-010.
1 Attach the plates 06S-300 with the screws 06S-280 to the post assembly
06S-270.
(d) Attach the post assembly 06S-270 with the screws 06S-310, 06S-340 and
For Myanmar Airways (MMA) use only
(f) Assemble the single door emergency unlocking device assembly 06S-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06S-420 and to the pin 06S-410 and attach the emergency
unlocking device pivot 06S-400, the snap catch 06S-420 and the pin
06S-410 to the emergency unlocking device housing 06S-380.
NOTE: Adjust the snap catch 06S-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06S-430 and attach the emergency unlocking device strike 06S-390 with
the bolt 06S-430 to the emergency unlocking device housing 06S-380.
(g) Attach the single door emergency unlocking device assembly 06S-370 with the
screws 06S-360 to the post assembly 06S-270.
(h) Attach the angle 06S-350 with the screws 06S-310 and the washers 06S-250
to the aft side wall assembly 06S-010.
(j) Attach the angles 06S-220 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(k) Attach the oxygen container assy 06S-230 with the screws 06S-240 and the
washers 06S-250 to the angles 06S-220.
(l) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06S-230.
(m) Attach the angle 06S-190 with the screws 06S-240 and the washers 06S-250
For Myanmar Airways (MMA) use only
(n) Attach the oxygen container assy cover 06S-180 with the screws 06S-200 and
the nuts 06S-210 to the angle 06S-190.
(p) Attach the studs 06S-260 and the washers 06S-250 to the oxygen container
assy cover 06S-180.
1 Attach the special screws 06S-150 and the special washers 06S-170 to
the aft side wall assembly 06S-010.
2 Attach the handle assemblies 06S-140 to the aft side wall assembly
06S-010.
SUBTASK 25-41-58-410-046-F01
D2549010414000
(0) Installation of the Side Wall (06S-1)
(a) Attach the fittings 06S-020, 06S-030 with the screws 06S-040, 06S-050.
1 Attach the plates 06S-300 with the screws 06S-280 to the post assembly
06S-270.
(c) Attach the post assembly 06S-270 with the screws 06S-310, 06S-340 and
the washers 06S-250.
(e) Assemble the single door emergency unlocking device assembly 06S-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06S-420 and to the pin 06S-410 and attach the emergency
For Myanmar Airways (MMA) use only
unlocking device pivot 06S-400, the snap catch 06S-420 and the pin
06S-410 to the emergency unlocking device housing 06S-380.
NOTE: Adjust the snap catch 06S-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06S-430 and attach the emergency unlocking device strike 06S-390 with
the bolt 06S-430 to the emergency unlocking device housing 06S-380.
(f) Attach the single door emergency unlocking device assembly 06S-370 with the
screws 06S-360 to the post assembly 06S-270.
(g) Attach the angle 06S-350 with the screws 06S-310 and the washers 06S-250
to the aft side wall assembly 06S-010.
(h) Attach the angles 06S-220 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(j) Attach the oxygen container assy 06S-230 with the screws 06S-240 and the
washers 06S-250 to the angles 06S-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06S-230.
(l) Attach the angle 06S-190 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(m) Attach the oxygen container assy cover 06S-180 with the screws 06S-200 and
the nuts 06S-210 to the angle 06S-190.
(n) Attach the studs 06S-260 and the washers 06S-250 to the oxygen container
assy cover 06S-180.
1 Attach the special screws 06S-150 and the special washers 06S-170 to
the aft side wall assembly 06S-010.
2 Attach the handle assemblies 06S-140 to the aft side wall assembly
06S-010.
For Myanmar Airways (MMA) use only
SUBTASK 25-41-58-410-046-G01
(a) Attach the fittings 06S-020, 06S-030 with the screws 06S-040, 06S-050.
1 Attach the plates 06S-300 with the screws 06S-280 to the post assembly
06S-270.
(c) Attach the post assembly 06S-270 with the screws 06S-310, 06S-340 and
the washers 06S-250.
(e) Assemble the single door emergency unlocking device assembly 06S-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06S-420 and to the pin 06S-410 and attach the emergency
unlocking device pivot 06S-400, the snap catch 06S-420 and the pin
06S-410 to the emergency unlocking device housing 06S-380.
NOTE: Adjust the snap catch 06S-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06S-430 and attach the emergency unlocking device strike 06S-390 with
the bolt 06S-430 to the emergency unlocking device housing 06S-380.
(f) Attach the single door emergency unlocking device assembly 06S-370 with the
For Myanmar Airways (MMA) use only
(g) Attach the angle 06S-350 with the screws 06S-310 and the washers 06S-250
to the aft side wall assembly 06S-010.
(h) Attach the angles 06S-220 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(j) Attach the oxygen container assy 06S-230 with the screws 06S-240, 06S-245
and the washers 06S-250 to the angles 06S-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06S-230.
(l) Attach the angle 06S-190 with the screws 06S-240 and the washers 06S-250
to the aft side wall assembly 06S-010.
(m) Attach the oxygen container assy cover 06S-180 with the screws 06S-200 and
the nuts 06S-210 to the angle 06S-190.
(n) Attach the studs 06S-260 and the washers 06S-250 to the oxygen container
assy cover 06S-180.
1 Attach the special screws 06S-150 and the special washers 06S-170 to
the aft side wall assembly 06S-010.
2 Attach the handle assemblies 06S-140 to the aft side wall assembly
06S-010.
TASK 25-41-58-400-819-U01
D2549026003400 D2549030812200
107. Installation of the Side Wall
A. General
This task gives you the installation and assembly procedures of the component.
REFERENCE DESIGNATION
C. Procedure
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE YOU
ASSEMBLE THEM.
SUBTASK 25-41-58-410-047-A01
D2549026003400
(1) Installation of the Side Wall (06T-1)
(a) Attach the fittings 06T-020, 06T-030 with the screws 06T-040, 06T-050.
1 Attach the plates 06T-300 with the screws 06T-280 to the post assembly
For Myanmar Airways (MMA) use only
06T-270.
(c) Attach the post assembly 06S-270 with the screws 06T-310, 06T-340 and
the washers 06T-250.
(e) Assemble the single door emergency unlocking device assembly 06T-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06T-420 and to the pin 06T-410 and attach the emergency
unlocking device pivot 06T-400, the snap catch 06T-420 and the pin
06T-410 to the emergency unlocking device housing 06T-380.
NOTE: Adjust the snap catch 06T-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06T-430 and attach the emergency unlocking device strike 06T-390 with
(f) Attach the single door emergency unlocking device assembly 06T-370 with the
screws 06T-360 to the post assembly 06T-270.
(g) Attach the angle 06T-350 with the screws 06T-310 and the washers 06T-250 to
the aft side wall assembly 06T-010.
(h) Attach the angles 06T-220 with the screws 06T-240 and the washers 06T-250
to the aft side wall assembly 06T-010.
(j) Attach the oxygen container assy 06T-230 with the screws 06T-240 and the
washers 06T-250 to the angles 06T-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06T-230.
For Myanmar Airways (MMA) use only
(l) Attach the angle 06T-190 with the screws 06T-240 and the washers 06T-250 to
the aft side wall assembly 06T-010.
(m) Attach the oxygen container assy cover 06T-180 with the screws 06T-200 and
the nuts 06T-210 to the angle 06T-190.
(n) Attach the studs 06T-260 and the washers 06T-250 to the oxygen container
assy cover 06T-180.
1 Attach the special screws 06T-150 and the special washers 06T-170 to
the aft side wall assembly 06T-010.
2 Attach the handle assemblies 06T-140 to the aft side wall assembly
06T-010.
SUBTASK 25-41-58-410-047-B01
D2549030812200
(0) Installation of the Side Wall (06T-1)
(a) Attach the fittings 06T-020, 06T-030 with the screws 06T-040, 06T-050.
1 Attach the plates 06T-300 with the screws 06T-280 to the post assembly
06T-270.
(c) Attach the post assembly 06S-270 with the screws 06T-310, 06T-340 and
the washers 06T-250.
(e) Assemble the single door emergency unlocking device assembly 06T-370 as
follows:
1 Apply the Material No. 08-007 Sealant, High Temperature to the snap
catch 06T-420 and to the pin 06T-410 and attach the emergency
unlocking device pivot 06T-400, the snap catch 06T-420 and the pin
06T-410 to the emergency unlocking device housing 06T-380.
NOTE: Adjust the snap catch 06T-420 a half turn before stop.
2 Apply the Material No. 08-007 Sealant, High Temperature to the bolt
06T-430 and attach the emergency unlocking device strike 06T-390 with
the bolt 06T-430 to the emergency unlocking device housing 06T-380.
(f) Attach the single door emergency unlocking device assembly 06T-370 with the
screws 06T-360 to the post assembly 06T-270.
(g) Attach the angle 06T-350 with the screws 06T-310 and the washers 06T-250 to
the aft side wall assembly 06T-010.
(h) Attach the angles 06T-220 with the screws 06T-240 and the washers 06T-250
to the aft side wall assembly 06T-010.
(j) Attach the oxygen container assy 06T-230 with the screws 06T-240 and the
washers 06T-250 to the angles 06T-220.
(k) Attach the ground cable in accordance with the Process and Material
Specification PMS 01-04-58 to the oxygen container assy 06T-230.
(l) Attach the angle 06T-190 with the screws 06T-240 and the washers 06T-250 to
the aft side wall assembly 06T-010.
(m) Attach the oxygen container assy cover 06T-180 with the screws 06T-200 and
the nuts 06T-210 to the angle 06T-190.
(n) Attach the studs 06T-260 and the washers 06T-250 to the oxygen container
assy cover 06T-180.
1 Attach the screws 06T-460 and the washers 06T-470 to the aft side wall
assembly 06T-010.
For Myanmar Airways (MMA) use only
2 Attach the handle 06T-450 to the screws 06T-460 and hold with the
setscrews 06T-480.
TASK 25-41-58-400-820-A01