Professional Documents
Culture Documents
IB (NA) - 0800503ENG-F - GT23 General Description
IB (NA) - 0800503ENG-F - GT23 General Description
5
against unauthorized access from external devices via a network.
To maintain the safety against unauthorized access via the Internet, take
Exercise care to avoid foreign matter such as chips and wire offcuts entering
the GOT. Not doing so can cause a fire, failure or malfunction.
For the analog-resistive film type touch panels, normally the adjustment is not
required.
measures such as installing a firewall. Plug the communication cable into the GOT interface or the connector of the However, the difference between a touched position and the object position
6
connected unit, and tighten the mounting screws and the terminal screws in may occur as the period of use elapses.
GT2310-VTBA GT2310-VTBD When any difference between a touched position and the object position
7 the specified torque range.
GT2308-VTBA GT2308-VTBD 8
CAUTION Undertightening can cause a short circuit or malfunction. occurs, execute the touch panel calibration.
Overtightening can cause a short circuit or malfunction due to the damage of When any difference between a touched position and the object position
9 Do not bundle the control and communication cables with main-circuit, power the screws or unit. occurs, other object may be activated.
Thank you for purchasing the GOT2000 Series. 0
or other wiring. This may cause an unexpected operation due to incorrect output or
Run the above cables separately from such wiring and keep them a minimum
of 100mm apart. malfunction.
Prior to use, please read both this manual and the
Not doing so noise can cause a malfunction.
[TEST OPERATION PRECAUTIONS]
detailed manual thoroughly to fully understand the 1
Do not press the GOT display section with a pointed material as a pen or
product. 2 driver. WARNING [PRECAUTIONS WHEN THE DATA STORAGE IS IN
Doing so can result in a damage or failure of the display section. USE]
3
When the GOT is connected to the Ethernet network, the available IP Before performing the test operations of the user creation monitor screen
4 address is restricted according to the system configuration. (such as turning ON or OFF bit device, changing the word device current
MODEL GT23-U-GD-E When a GOT2000 series model and a GOT1000 series model are on an value, changing the settings or current values of the timer or counter, and WARNING
5
Ethernet network, do not set the IP address 192.168.0.18 for the GOTs and changing the buffer memory current value), read through the manual
Model the controllers on this network.
1D7MI4 6 carefully and make yourself familiar with the operation method. If the SD card mounted on drive A of the GOT is removed while the GOT is
code Doing so can cause IP address duplication at the GOT startup, adversely During test operation, never change the data of the devices which are used to accessed, processing for the GOT might be interrupted about for 20
7 affecting the communication of the device with the IP address 192.168.0.18. perform significant operation for the system. seconds.The GOT cannot be operated during this period. The functions that
IB(NA)-0800503ENG-F(1812)MEE 8 The operation at the IP address duplication depends on the devices and the False output or malfunction can cause an accident. run in the background including a screen updating, alarm, logging, scripts,
system. and others are also interrupted.Since this interruption makes an impact to the
9 Turn on the controllers and the network devices to be ready for system operation, it might cause failure.After checking the light off of SD card
© 2013 MITSUBISHI ELECTRIC CORPORATION
0 communication before they communicate with the GOT. [STARTUP/MAINTENANCE PRECAUTIONS] access LED, remove the SD card.
Failure to do so can cause a communication error on the GOT.
SAFETY PRECAUTIONS When the GOT is subject to shock or vibration, or some colors appear on the
(Always read these precautions before using this equipment.) screen of the GOT, the screen of the GOT might flicker. WARNING CAUTION
Before using this product, please read this manual and the relevant When power is on, do not touch the terminals.
If the data storage mounted on the GOT is removed while the GOT is
manuals introduced in this manual carefully and pay full attention to [MOUNTING PRECAUTIONS] Doing so can cause an electric shock or malfunction.
accessed, the data storage and files are damaged.To remove the data
Correctly connect the battery connector. storage from the GOT, check that the access to the data storage in SD card
safety to handle the product correctly.
The precautions given in this manual are concerned with this prod-
WARNING Do not charge, disassemble, heat, short-circuit, solder, or throw the battery
into the fire.
access LED, the system signal, and others is not performed.
Doing so will cause the battery to produce heat, explode, or ignite, resulting in Turning off the GOT while it accesses the SD card results in damage to the
uct. Be sure to shut off all phases of the external power supply used by the injury and fire. SD card and files.
In this manual, the safety precautions are ranked as "WARNING" system before mounting or removing the GOT main unit to/from the panel. Before starting cleaning or terminal screw retightening, always switch off the When inserting a SD card into the GOT, make sure to close the SD card
and "CAUTION". Not doing so can cause the unit to fail or malfunction. power externally in all phases. cover. Failure to do so causes the data not to be read or written.
Not switching the power off in all phases can cause a unit failure or When removing the SD card from the GOT, make sure to support the SD card
malfunction. by hand as it may pop out.Failure to do so may cause the SD card to drop
Indicates that incorrect handling may cause CAUTION Undertightening can cause a short circuit or malfunction. from the GOT, resulting in a failure or break.
WARNING hazardous conditions, resulting in death or Overtightening can cause a short circuit or malfunction due to the damage of
the screws or unit.
When inserting a USB device into a USB interface of the GOT, make sure to
insert the device into the interface firmly.Failure to do so may cause the USB
severe injury. Use the GOT in the environment that satisfies the general specifications device to drop from the GOT, resulting in a failure or break
described in this manual.
Not doing so can cause an electric shock, fire, malfunction or product Before removing the USB device from the GOT, follow the procedure for
removal on the utility screen of the GOT. After the successful completion
Indicates that incorrect handling may cause damage or deterioration. CAUTION dialog is displayed, remove the USB device by hand carefully.Failure to do so
CAUTION hazardous conditions, resulting in medium or When mounting the GOT to the control panel, tighten the mounting screws in
the specified torque range (0.36 N•m to 0.48 N•m) with a Phillips-head
may cause the USB device to drop from the GOT, resulting in a failure or
slight personal injury or physical damage. Do not disassemble or modify the unit. break.
screwdriver No.2.
Undertightening can cause the GOT to drop, short circuit or malfunction. Doing so can cause a failure, malfunction, injury or fire.
Overtightening can cause a drop, short circuit or malfunction due to the Do not touch the conductive and electronic parts of the unit directly. [DISPOSAL PRECAUTIONS]
damage of the screws or the GOT. Doing so can cause a unit malfunction or failure.
Remove the protective film of the GOT.
Note that the CAUTION level may lead to a serious accident When the user continues using the GOT with the protective film, the film may
The cables connected to the unit must be run in ducts or clamped. CAUTION
according to the circumstances. not be removed. Not doing so can cause the unit or cable to be damaged due to the dangling,
Always follow the instructions of both levels because they are import- Operate and store the GOT in environments without direct sunlight, high motion or accidental pulling of the cables or can cause a malfunction due to a When disposing of this product, treat it as industrial waste.
temperature, dust, humidity, and vibrations. cable connection fault. When disposing of batteries, separate them from other wastes according to
ant to personal safety.
When using the GOT in the environment of oil or chemicals, use the When unplugging the cable connected to the unit, do not hold and pull from the local regulations.
Please save this manual to make it accessible when required and protective cover for oil.Failure to do so may cause failure or malfunction due the cable portion. (Refer to the GOT2000 Series User’s Manual (Hardware) for details of the
always forward it to the end user. to the oil or chemical entering into the GOT. Doing so can cause the unit or cable to be damaged or can cause a battery directive in the EU member states.)
malfunction due to a cable connection fault.
[DESIGN PRECAUTIONS] [WIRING PRECAUTIONS] Do not drop the module or subject it to strong shock. A module damage may [TRANSPORTATION PRECAUTIONS]
result.
WARNING WARNING Do not drop or give an impact to the battery mounted to the unit. CAUTION
Doing so may damage the battery, causing the battery fluid to leak inside the
Some failures of the GOT, communication unit or cable may keep the outputs Be sure to shut off all phases of the external power supply used by the battery.
system before wiring. When transporting lithium batteries, make sure to treat them based on the
on or off. If the battery is dropped or given an impact, dispose of it without using.
Some failures of a touch panel may cause malfunction of the input objects Failure to do so may result in an electric shock, product damage or transport regulations.
such as a touch switch. malfunctions. Before touching the unit, always touch grounded metals, etc. to discharge (Refer to the GOT2000 Series User’s Manual (Hardware) for details of the
An external monitoring circuit should be provided to check for output signals static electricity from human body, etc. regulated models.)
which may lead to a serious accident. Not doing so can cause the unit to fail or malfunction. Make sure to transport the GOT main unit and/or relevant unit(s) in the
Not doing so can cause an accident due to false output or malfunction.
Do not use the GOT as the warning device that may cause a serious
CAUTION Use the battery manufactured by Mitsubishi Electric Corporation. manner they will not be exposed to the impact exceeding the impact
Use of other batteries may cause a risk of fire or explosion. resistance described in the general specifications of this manual, as they are
accident.
An independent and redundant hardware or mechanical interlock is required Make sure to ground the FG terminal and LG terminal of the GOT power Dispose of used battery promptly. precision devices.
to configure the device that displays and outputs serious warning. supply section to the protective ground conductors dedicated to the GOT with Keep away from children.Do not disassemble and do not dispose of in fire. Failure to do so may cause the unit to fail.
Failure to observe this instruction may result in an accident due to incorrect a ground resistance of 100 Ω or less. Be sure to shut off all phases of the external power supply before replacing Check if the unit operates correctly after transportation.
output or malfunction.
When tightening the terminal screws, use a Phillips-head screwdriver No.2. the battery or using the dip switch of the terminating resistor. When fumigants that contain halogen materials such as fluorine, chlorine,
The GOT backlight failure disables the operation on the touch switch(s).
When the GOT backlight has a failure, the POWER LED blinks (orange/blue) Terminal screws which are not to be used must be tightened always at torque Not doing so can cause the unit to fail or malfunction by static electricity. bromine, and iodine are used for disinfecting and protecting wooden
and the display section dims. In such a case, the input by the touch switch(s) 0.5 N•m to 0.8 N•m. packaging from insects, they cause malfunction when entering our products.
is disabled. Otherwise there will be a danger of short circuit against the solderless Please take necessary precautions to ensure that remaining materials from
The display section of the GOT is an analog-resistive type touch panel. terminals. fumigant do not enter our products, or treat packaging with methods other
Do not touch two points or more simultaneously on the display section. than fumigation (heat method).
Doing so may cause a touch switch near the touched points to operate Use applicable solderless terminals and tighten them with the specified
torque. Additionally, disinfect and protect wood from insects before packing products.
unexpectedly, or may cause an accident due to an incorrect output or
malfunction. If any solderless spade terminal is used, it may be disconnected
When programs or parameters of the controller (such as a PLC) that is when the terminal screw comes loose, resulting in failure.
monitored by the GOT are changed, be sure to reset the GOT, or turn on the Correctly wire the GOT power supply section after confirming the rated
unit again after shutting off the power as soon as possible.
Not doing so can cause an accident due to false output or malfunction. voltage and terminal arrangement of the product.
If a communication fault (including cable disconnection) occurs during Not doing so can cause a fire or failure.
monitoring on the GOT, communication between the GOT and PLC CPU is Tighten the terminal screws of the GOT power supply section in the specified
suspended and the GOT becomes inoperative. torque range (0.5 N•m to 0.8 N•m). Undertightening can cause a short circuit
A system where the GOT is used should be configured to perform any or malfunction.Overtightening can cause a short circuit or malfunction due to
significant operation to the system by using the switches of a device other
than the GOT on the assumption that a GOT communication fault will occur. the damage of the screws or the GOT.
Not doing so can cause an accident due to false output or malfunction.
Installation fitting 4
10
10
175 (6.89)
199 (7.84)
Note
Operation at momentary failure
• If an instantaneous power failure occurs in the power supply and continues for more
than the permissible period, the GOT will be reset.
1. FEATURES • Make sure to power on the unit more than 5 seconds after power-off. 166 (6.54)
(0.39)
228 (8.98)
(0.39)
10
10
(0.24)
(0.24)
6
56 (2.20)
B
to the cabinet of the
by two or more levels of isolating transformers from the public power GT2308 +2 (0.08) +2 (0.08)
equipment. noise, the wire itself carries a large noise content and thus short 0 (0) 0 (0)
distribution.
IEC61000-4-3 Immunity test in 80-1000MHz:10V/m wiring means that the wire is prevented from acting as an Unit: mm (inch)
Radiated which field is 1.4-2GHz:3V/m antenna.
electromagnetic irradiated to the 2.0-2.7GHz:1V/m
Note) A long conductor will become a more efficient antenna at
4.2.3 Control panel
field AM modulation product. 80%AM modulation@1kHz
high frequency. Because the GOT is open type equipment (device designed to be stored
IEC61000-4-4
Immunity test in Power cable: 2kV
(b) The earth wire led from the earthing point must be twisted with
5.3 Mounting Position
Fast transient burst
which burst noise is Digital I/O: 1kV within another device), be sure to use it only when installed in a control
noise*1
applied to the power Analog I/O: 1kV the power supply wires. panel. When mounting the GOT, the following clearances must be maintained
line and signal lines. Signal cable: 1kV By twisting with the earthing wire, noise flowing from the power from other structures and devices.
(1) Shock Protection
AC power type supply wires can be relieved to the earthing. However, if a filter is Some cables may need to be longer than the specified dimensions when
Power line (between line and In order to prevent those who are unfamiliar with power facility,
ground): 2kV
installed on the power supply wires, the wires and the earthing e.g., an operator, from getting a shock, make sure to take the connecting to the GOT.
Power line (between lines) wire may not need to be twisted. following measures on the control panel. Therefore, consider the connector dimensions and bending radius of the
EN61131-2 : 1kV cable as well for installation.
(a) Store the GOT within the control panel locked, and allow only
: 2007 Immunity test in Data communication port 4.1.3 Noise filter (power supply line filter) those who are familiar with power facility to unlock the panel. For the lead-in allowance for cables at the bottom of the GOT, refer to
IEC61000-4-5 which lightening : 1kV
Surge immunity*1 surge is applied to DC power type (b)Build the structure in order that the power supply will be shut off the GOT2000 Series User’s Manual (Hardware).
The noise filter (power supply line filter) is a device effective to reduce
the product. Power line (between line and
conducted noise. Except some models, installation of a noise filter onto when the control panel is opened.
ground) : 0.5kV
the power supply lines is not necessary. However conducted noise can (2) Dustproof and waterproof features B
Power line (between lines)
be reduced if it is installed. (The noise filter is generally effective for The control panel also provides protection from dust, water and
: 0.5kV
Data communication port reducing conducted noise in the band of 10MHz or less.) Usage of the other substances. Insufficient ingression protection may lower the
C D E
: 1kV following filters is recommended. insulation withstand voltage, resulting in insulation destruction.
Immunity test in The insulation in the GOT is designed to cope with the pollution
IEC61000-4-6 which a noise Model name FN343-3/05 FN660-6/06 RSHN-2003 level 2, so use in an environment with pollustion level 2 or better. A
Power line: 10V
Conducted RF inducted on the Manufacturer SCHAFFNER SCHAFFNER TDK
Data communication port: 10V Pollution level 1: An environment where the air is dry and conductive
immunity*1 power and signal Panel thickness: 1.6 to 4mm
Rated current 3A 6A 3A dust does not exist.
lines is applied.
(0.06 to 0.16 inch)
Test for checking Rated voltage 250V Pollution level 2: An environment where conductive dust does not
normal operations usually exist, but occasional temporary conductivity
under the The precautions required when installing a noise filter are described occurs due to the accumulated dust. According to the dimensions in the following table, leave clearances
IEC61000-4-8
Power supply
circumstance below. Generally, this is the level for inside the control panel between the GOT and the other devices. The values enclosed in square
exposed to the 30 A/m (1) Do not install the input and output cables of the noise filter together equivalent a control room or on the floor of a typical brackets apply to the case where no other equipment generating
frequency magnetic
ferromagnetic field
field immunity to prevent the output side noise will be inducted into the input side factory. radiated noise (such as a contactor) or heat is installed near the GOT.
noise of the power
supply frequency cable where noise has been eliminated by the noise filer. Pollution level 3: An environment where conductive dust exits and However, keep the ambient temperature of the GOT to 55°C or lower.
(50/60Hz). Input side conductivity may be generated due to the accumulated
Input side dust.
IEC61000-4-11 AC power type (power supply side) (power supply side)
Test for checking An environment for a typical factory floor.
Instantaneous 0.5 cycle 0% (interval 1 to 10s)
normal operations
power failure and
at instantaneous
250/300 cycle 0% Pollution level 4: Continuous conductivity may occur due to rain, snow,
voltage dips 10/12 cycle 40% etc. An outdoor environment.
power failure. Induction
immunity 25/30 cycle 70%
*1: The GOT is an open type device (device installed to another device) and must
Filter
Output side
Filter
Output side
4.2.4 Grounding
be installed in a conductive control panel. (device side) (device side) The following are applicable ground terminals. Use them in the grounded
The above test items are conducted in the condition where the GOT is installed state.
on the conductive control panel and combined with the Mitsubishi Electric PLC. • Installing the input and output cables • Separate the input cable from the output
together will cause noise induction. cable. Be sure to ground the GOT for ensuring the safety and complying with
*2: QP (Quasi-Peak): Quasi-peak value, Mean: Average value
(2) Connect the noise filter's ground terminal to the control panel with the EMC Directive.
the shortest cable as possible (approx. 10cm (3.94 in.) or less). Functional grounding : Improves the noise resistance.
structures et dispositifs. maintenance and inspection for the GOT. Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany
Tel: +49-2102-486-0
Display section
Certains câbles peuvent être plus longs que les dimensions spécifiées UK Mitsubishi Electric Europe B.V. UK Branch
Travellers Lane, Hatfield, Hertfordshire, AL10 8XB, U.K.
GOT lors de la connexion au GOT. Tel: +44-1707-28-8780
105° Par conséquent, prenez également en compte les dimensions du Italy Mitsubishi Electric Europe B.V. Italian Branch
connecteur et le rayon de courbure du câble pour l'installation. Centro Direzionale Colleoni - Palazzo Sirio, Viale Colleoni 7,
Agrate Brianza (MB), Italy
Pour connaître l'espace à laisser pour les câbles sous le GOT, référez- Tel: +39-039-60531
60° vous au manuel GOT2000 Series User’s Manual (Hardware). Spain Mitsubishi Electric Europe B.V. Spanish Branch
Carretera de Rubi 76-80-Apdo.420, 08190 Sant Cugat del Valles (Barcelona), Spain
Tel: +34-935-65-3131
Panel or others France Mitsubishi Electric Europe B.V. French Branch
B 25, Boulevard des Bouvets, 92741 Nanterre Cedex, France
Tel: +33-1-55-68-55-68
Czech Mitsubishi Electric Europe B.V. Czech Branch
C D E
Avenir Business Park, Radlicka 751/113e, 158 00 Praha 5, Czech Republic
Tel: +420-251-551-470
Turkey Mitsubishi Electric Turkey A.S. Umraniye Branch
A Serifali Mahallesi Nutuk Sokak No:5, TR-34775 Umraniye / Istanbul, Turkey
Tel: +90-216-526-3990
Poland Mitsubishi Electric Europe B.V. Polish Branch
Épaisseur du panneau : 1,6 à 4mm
ul. Krakowska 50, 32-083 Balice, Poland
(0,06 à 0,16 pouce) Tel: +48-12-347-65-00
Russia Mitsubishi Electric (Russia) LLC St. Petersburg Branch
Laissez les espaces entre le GOT et les autres dispositifs en fonction Piskarevsky pr. 2, bld 2, lit “Sch”, BC “Benua”, office 720;
RU-195027 St. Petersburg, Russia
des dimensions contenues dans le tableau suivant. Les valeurs entre Tel: +7-812-633-3497
parenthèses s'appliquent au cas où aucun dispositif générant des South Africa Adroit Technologies
émissions sonores (comme un contacteur) ou de la chaleur n'est installé 20 Waterford Office Park, 189 Witkoppen Road, Fourways, Johannesburg, South Africa
Tel: +27-11-658-8100
près du GOT. Toutefois, maintenez la température ambiante du GOT à China Mitsubishi Electric Automation (China) Ltd.
55°C ou moins. No.1386 Hongqiao Road, Mitsubishi Electric Automation Center, Shanghai, China
Unité : mm (pouce) Tel: +86-21-2322-3030
Taiwan SETSUYO ENTERPRISE CO., LTD.
Article GT2310 GT2308 6F, No.105, Wugong 3rd Road, Wugu District, New Taipei City 24889, Taiwan
Tel: +886-2-2299-2499
48 (1,89) ou plus Korea Mitsubishi Electric Automation Korea Co., Ltd.
A
[18 (0,71) ou plus] 7F-9F, Gangseo Hangang Xi-tower A, 401, Yangcheon-ro, Gangseo-Gu,
Seoul 07528, Korea
78 (3,07) ou plus Tel: +82-2-3660-9530
B
[18 (0,71) ou plus] Singapore Mitsubishi Electric Asia Pte. Ltd.
307 Alexandra Road, Mitsubishi Electric Building, Singapore 159943
Quand la carte SD est 50 (1,97) ou plus Tel: +65-6473-2308
50 (1,97) ou plus
utilisée [20 (0,79) ou plus] Thailand Mitsubishi Electric Factory Automation (Thailand) Co., Ltd.
C 12th Floor, SV.City Building, Office Tower 1, No. 896/19 and 20 Rama 3 Road,
Quand la carte SD n'est 50 (1,97) ou plus Kwaeng Bangpongpang, Khet Yannawa, Bangkok 10120, Thailand
pas utilisée [20 (0,79) ou plus] Tel: +66-2682-6522 to 31
Indonesia PT. Mitsubishi Electric Indonesia
50 (1,97) ou plus Gedung Jaya 11th Floor, JL. MH. Thamrin No.12, Jakarta Pusat 10340, Indonesia
D Tel: +62-21-3192-6461
[20 (0,79) ou plus]
Vietnam Mitsubishi Electric Vietnam Co., LTD. Ho Chi Minh Head Office
100 (3,94) ou plus Unit 01-04, 10th Floor, Vincom Center, 72 Le Thanh Ton Street, District 1,
E*1 Ho Chi Minh City, Vietnam
[20 (0,79) ou plus]
Tel: +84-8-3910-5945
*1: Pour ouvrir ou fermer le couvercle de la batterie : 72 (2,83) ou plus India Mitsubishi Electric India Pvt. Ltd. Pune Branch
Emerald House, EL -3, J Block, M.I.D.C., Bhosari, Pune - 411026, Maharashtra, India
Tel: +91-20-2710-2000
Australia Mitsubishi Electric Australia Pty. Ltd.
348 Victoria Road, P.O. Box 11, Rydalmere, N.S.W. 2116, Australia
Tel: +61-2-9684-7777
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN
When exported from Japan, this manual does not require application to the Ministry
of Economy, Trade and Industry for service transaction permission.
Specifications subject to change without notice.
Printed in Japan, December 2018.