Professional Documents
Culture Documents
Baby Lock BL101 Sewing Machine Service Manual
Baby Lock BL101 Sewing Machine Service Manual
Baby Lock BL101 Sewing Machine Service Manual
com
SERVICE MANUAL
Model BL-101
All manuals and user guides at all-guides.com
1. Position of needle
Set needle slightly right-down ward in order to make its penetration stronger.
All manuals and user guides at all-guides.com
1
3. Adjustment of looper position
2
All manuals and user guides at all-guides.com
Make sure both left and right cloth pressers to hold the cloth lifter.
(No 005226 ~ )
3
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
All manuals and user guides at all-guides.com
SERVICE MANUAL
MODEL BLCS
Serial Numbers
Vol 2.0
All manuals and user guides at all-guides.com
1.Construction of Covers
Adjusting gauge
from right side of chain
72.8
55.4
presser foot
Height of
Height of overlock
right needle(O 2 )
4.6
4.9 8.6
10.1
Height of
feed dog
1
1
2. Adjustment of Needle,Chain lopper & Presser foot
Height of needle Chain looper adjustment
ELx705CF 90/14 Needle guard adjustment
ELx705CF 90/14 ELx705CF 90/14 Chain
Chain Needle
Needle 0 0 FRONT
FRONT 0 SIDE
2.3+0.2
SIDE Chain needle
0.2-0.3 front needle
guard
C3 Needle
C3 Needle 0
0.1
2
1.9 0-0.02
Needle plate Back
needle guard
R7
10.2+0.05
2.
Chain needle
All manuals and user guides at all-guides.com
4
Height of presser foot & Chain looper
0.
C3 Needle
0 1
ELx705CF 90/14
4.5+0.2
0-0.1
All manuals and user guides at all-guides.com
4-1.Tension release
a) In case you replace face cover, make sure the tension release lever
catches the Tension release pin correctly (fig.A)
b) Double check disks are open perfectly when presser bar lifter is lifted.
3
All manuals and user guides at all-guides.com
0.9 +0.1
0
4.Tension release & Dropped feed dog adjustment
E
B
4
All manuals and user guides at all-guides.com
6. Checking pump
6-1 Checking deflate from pump
Holding the pump tube 6, push down the pump lever 15 and check if air is deflated
from pump or not.
a) Bring the pump lever to the lowest position and fix it with Scotch tape or something like that.
i) Fit piston driving arm to piston driving shaft properly and tighten fixing screw SM3005IK firmly.
(It will be easy to fit the armto the shaft, if you push the shaft to the leftward direction.)
5
All manuals and user guides at all-guides.com
5.Checking thread
steel pipe joint
Threading steel
pipe
Joint
Proper position Unproper position
6.Checking pump 2
3
1 4
3
10 4
11 17
14 12
13
16
15
6
All manuals and user guides at all-guides.com
7. TROUBLE SHOOTING
7
BLCS2
All manuals and user guides at all-guides.com
SERVICE MANUAL
Basic Adjustment
MODEL BLE1
BLE1SX
BLE1DX
BLE1AT
BLE3ATW
BLE8
BLE8W
BLCS
Serial Numbers
Vol. 6.1
All manuals and user guides at all-guides.com
1.NEEDLE
NOTE: Before all adjustment,
you are required to change all needles to new and correct ones.
Front Groove
Back Groove
1
All manuals and user guides at all-guides.com
Height of needle
Organ Organ Organ Organ
HAx1SP/CR 75/11 HAx1SP/CR 90/14 ELx705CF 90/14 ELx705CF 90/14
Right
11.5 +0.1
10.6+0.1
Needle plate Needle
Needle plate Needle plate
plate
Raise
Screw A
Screw B
Needles
Needle position
Needle plate
2
All manuals and user guides at all-guides.com
mm
check JET AIR THREADING.
.1
.7 +0
55
a) Replacement of lower looper
Lower looper
Slide the pipe rubber, and loosen the screw. fixing screw
Replace new lower looper, and slightly tighten the screw.
Adjust the radius 55.4mm+0.1, and firmly tighten the screw. Looper arm
Replace the pipe rubber. screw for
adjusting position
Right
Needle
b) Lower looper position
#11(#75)Needle
0
Turn the handwheel, and bring lower looper to 5.2 -0.1 mm (SX,DX,AT)
the far left. #14(#90)Needle
0
Loosen looper arm screw, and adjust lower looper 5.3 -0.1 mm (ATW)
to the correct position. #14(#90)Needle
0
You are required to check the distance of tip of 4.8 -0.1 mm
lower looper and needle. (BLE5, BLE8W))
Lower looper
position
Loosen rear needle guard screw ,and adjust rear needle Rear
needle guard
guard to the correct position.
screw
Front
needle
c) Adjusting needle guards guard left,right
needle
Loosen front needle guard screw,
and adjust front needle guard to
0
the correct position.
Front
Rear needle guard can be adjusted needle
Front needle guard guard
by bending. fixingscrew
0
Rear
needle guard
3
All manuals and user guides at all-guides.com
Slide the pipe rubber, and loosen the screw. Upper looper
Replace new lower looper, slightly tighten the screw. fixing screw
The distance from looper from shaft is approx. 0.8mm,
and firmly tighten the screw.
Replace the pipe rubber.
Looper arm
screw for adjusting position
0
d) The distance between upper looper and lower looper
Presser foot
Pressure
0.9 - 1.0mm
Clockwise Raise
Screw A
Counter-clockwise Lower
Adjusting screw
1mm
5
All manuals and user guides at all-guides.com
How to adjust
Screw
Differential feed
positining ratchet
Connecting
shaft
Differential feed
adjuating lever
Stitch length
dial
6
All manuals and user guides at all-guides.com
8-1. REPLACEMENT OF CHAINING TONGUE (EXCEPT BL3ATW)
a) Remove needle plate.
b) Loosen two screws of chaining tongue
cover plate and remove it. Cover plate
Cheining tongue
c) Watching carefully not to jump out steel
ball, remove chaining tongue and replace it.
d) You are requied to check the fixing position
of the chaining tongue, after replacing it. Steel ball
e) Rotate stitch length dial max. 4 to rolled hem max.4,
make sure the chaining tongue is moved smoothly Spring
to rolled hem position.
Pin
7
All manuals and user guides at all-guides.com
9. REPLACEMENT OF KNIVES
UPPER KNIFE
a) Remove upper knife and replace it.
b) Fixing screw temporaly, turn the hand pulley and bring the upper knife to
the lowest positon.
c) Adjust upper knife to be 1-1.5mm overlapping with cutting face of lower knife.
d) Tighten firmly fixing screw.
LOWER KNIFE
a) Remove both knives and replace it.
b) Fix screw of lower knife temporaly.
c) Adjust lower knife to be 0-0.2mm down from surface of needle plate.
d) Tighten firmly fixing screw.
e) Replace upper knife as same as avobe.
Needle Plate
-0.2
1-1.5mm
0
Screw
Screw
Upper Knife Adjustment Lower Knife Adjustment
Needle plate
adjusting screw
Needles
Needles
Needle plate
adjusting screw
Machine Settings
Needle : Right Needle(O2)
Thread : No Use
Stitch Width : M
Stitch Length: 2.5
Differencial feed : N
Fabric : Cotton broad 1 layer
Fixing screw
of Knife holder
b-1) Cutting width adjustment
Loosen fixing screw of knife holder,
and adjust knife holder right or left. 5.5
3.0
tighten the screw.
Make sure cutting width.
0.5mm
9
.
All manuals and user guides at all-guides.com
Standard Position
A
B
6 C
3 7 2 D
9
4 5 10
11
All manuals and user guides at all-guides.com
NOTE: In case that the looper threader does not work properly,
please check and confirm the following points.
Depress the machine lock button and bring the joint pipes to
the far left position. (the locked position)
Move the release lever right and left direction slowly and
gently while pushing the machine lock button and check whether
the joint pipes move smothly or not.
In case that the joint pipes do not move smoothly, see 13-b).
(p.12)
In case that the end of the joint pipes are incorrect position,
see 13-b). (p.13)
12
All manuals and user guides at all-guides.com
Grease
(MOLYKOTE EM-50L)
Piston driving
arm Piston cap
B5825-03A
Piston driving
arm fixing screw
Piston driving
arm shaft
13
All manuals and user guides at all-guides.com
NOTE: In case that adjusting JET AIR THREADING, do not lay down
the machine body on the side.
CHAIN LOOPER
Loosen the screw "C" and "D" , and adjust the position of threading pipe guide 4 and
chain looper threading pipe holder set 5 , so that joint pipe 6 may move smothly.
- In case that you cannot adjust it properly, replace the upper, lower or chain looper threading
pipes with new ones and re-adjust it so that joint pipes may move smoothly.
Screw
B Screw A
2
1 3
Screw
6 C Screw
5 4 D
14
All manuals and user guides at all-guides.com
NOTE: In case that adjusting JET AIR THREADING, do not lay down
the machine body on the side.
c) In case that the end of joint pipe is not in the center of joint pipe receiver.
Depress the machine lock button and bring the joint pipes to the far left position.
(the locked position)
Loosen the 2 screws of threading position setting plate with hexagonal wrench.
Slightly rotate handwheel with right hand (within the angle of 10 degrees) while pushing
the lock button and moving the releace lever right and left direction slowly, and gently
with left hand, find out the best position that the end of joint pipes are in the center
of looper joint pipe receivers.
When you tighten 2 screws, you push handwheel to the leftward direction with your
right hand and push the threading position setting plate to the rightward direction with
your left hand. You are required to check a play of handwheel rightward and leftward
direction.
Threading position
setting plate
Fixing screws
Tool
15
All manuals and user guides at all-guides.com
Fixing screws
Joint pipe
springs
Upper looper
threading pipe
16
All manuals and user guides at all-guides.com
1) Loosen the screw (1) and remove Frontdisk moving arm set.
2) Remove Rear disk moving arm set.
3) Loosen the screw (2) and replace Cam.The screw should be placed at the flat of shaft.
4) Replace Rear disk moving arm set.
5)Turn handwheel and bring the roller of Rear disk moving arm set at the bottom position of Cam.
Insert 0.4mm thickness gauge between disk pushing shaft and Rear pushing arm section.
Push and keep Rear disk pushing arm section at bottom of pre-tenstion position,adjust Cam to
the roller has just touched on the bottom of Cam. Tighten the Screw (2).
Remove thickness gauge, make sure the distance of disks is 0.9mm when opened.
6) Replace Front disk moving arm set.
7) Turn handwheel and bring the roller of Front disk moving arm set at the bottom position of Cam.
Insert 0.4mm thickness gauge between disk pushing shaft and front pushing arm set.
Push and keep Front disk pushing arm set at bottom of pre-tenstion position,and adjust Cam to
the roller has just touched on the bottom of Cam.
Hold Front disk pushing arm set to leftward and Front disk moving arm set to rightward,
and tighten the Screw (1).
Remove thickness gauge, make sure the distance of disks is 0.9mm when opened.
Make sure Front disk pushing arm set does not have a play.
0.9mm 0.4mm
Screw(1)
Screw(2)
Distance of disks Distance of
when opend pre-tension
Cam
Front disk moving
arm set
Rear disk moving
arm set
0.4
0.4
Front disk
pushing arm set
Screw(2)
Screw(1)
Cam
Rear disk moving Cam
arm set Front disk moving
arm set
Adjustment of Rear disks
Adjustment of Front disks
17
.
All manuals and user guides at all-guides.com
17. REPLACEMENT OF LOOPER DRIVING CAM AND ROLLER
To replace
Before remove the cams on the main shaft, you are required to check the distance of gap
between rightside of right bush and left side of handwheel (A).
1) Remove Spool stand set, Bace plate, Side cover, Face cover, Knife holder cover and Knife cover set.
2) Loosen all screws of Timing pully (1), Machine engage plate set(2), Balancer (5), Lower looper
driving cam (7), Chain looper driving cam (8), Feed dog driving cam (9) and Knife driving cam (10)
on the main shaft.
3) Remove the main shaft with the handwheel to the rightward.
4) Remove the nut (11) of Needle driving rod set (6) and loosen the screw (13).
5) Remove Needle driving rod set (6) from Lower looper driving cam (7).
6) Remove lower looper driving cam (7) with slightly twist from Chain looper thread take-up and
Chain looper driving cam.
7) Replace Lower looper driving cam or Rollers.
5.Balancer
1
3
10 2
4 A
9 8 7 5
6
18
.
All manuals and user guides at all-guides.com
19
.
All manuals and user guides at all-guides.com
1
A
2
3
4
5
6
8 7
9
10
Main shaft
0.2mm 7
12mm
For BLE8, BLE8W, BLCS For BLE1SX, BLE1, BLE1DX, BLE1LX, BLE1AT, BLE3ATW
.
Distance of chain looper tip
from center of chain looper shaft
18. Adjusting Gauge
(BLE5, BLE8W)
Distance of lower looper tip 72.8
from center of lower looper shaft 55.7
For BLCS(3)
4.6 Height of presser foot
For BLE5,BLE8W
For BLE3ATW
For BLE1SX, DX, AT
Distance of lower looper tip
Height of
feed dog
4.8
10.6
11.2
11.5
All manuals and user guides at all-guides.com
12.5
Distance of lower looper tip
Distance of Upper looper tip from right side of right needle
From right side of right needle 8.6 5.3 (SX, DX, AT, ATW)