Professional Documents
Culture Documents
ETX-205A Ds
ETX-205A Ds
ETX-205A Ds
Data Sheet
ETX-205A
Carrier Ethernet Demarcation Device
• Multirate FE/GbE combo ports and E1/T1 ports allow flexible service offering in
one unit for capex and opex savings
• Flow-based traffic management with H-QOS per EVC for SLA enforcement at
customer premises, enabling MEF-certified EPL and EVPL services
• Ethernet OAM and performance monitoring at wire speed, for reliable and
accurate SLA monitoring, enabling efficient diagnostics and troubleshooting
Demarcation point for • Enhanced RFC-2544 analyzer for SLA verification, ensuring customer
satisfaction immediately after turn-up
SLA-based Ethernet • Synchronous Ethernet and IEEE-1588v2 PTP, seamlessly bridging
synchronization domains
business services and
mobile backhaul The ETX-205A Carrier Ethernet ETX-205A delivers IP VPN, VoIP, and
demarcation device offers Ethernet dedicated Internet access over the same
demarcation functionality for business physical link as a Layer-2 LAN-to-LAN
services as well as cell-site gateway service, all with differentiated quality of
functionality for 2G, 3G, and 4G/LTE service and end-to-end monitoring. It can
mobile backhauling applications. It also deliver E1, T1, and NxDS0 circuits.
provides end-to-end service control and Incorporating RAD’s SyncToP™
performance management across packet synchronization and timing over packet
networks. feature set, ETX-205A utilizes standard
The device delivers SLA-based business technologies to ensure highly accurate
services to the customer premises over phase and frequency recovery and
native Ethernet interfaces, terminating distribution over both the physical and
over any type of packet network. packet layers.
ETX-205A transports up to five Gbps of
user traffic while ensuring SDH/SONET-like
performance and Five Nines reliability.
ETX-205A
Carrier Ethernet Demarcation Device
All ETX-205A units are equipped with • Mobile demarcation device – ETX-205A optional MAC change) across the
SFP/copper combo Ethernet ports, is installed at the operator tower and network,to peer supported protocols
enabling flexible mixture of fiber optic and controller sites equipped with Ethernet (IEEE 802.3-2005 and LACP), or to discard
copper interfaces in one device. The SFP and PDH ports, connecting the the L2CP frames.
ports accommodate a wide range of Fast 2G/3G/4G/LTE NodeB or eNodeB to the ETX-205A provides LACP transparency by
Ethernet and Gigabit Ethernet SFP packet network, providing translating LACP traffic to L2PT inside the
transceivers, allowing service providers to sophisticated synchronization and network, thus enabling end-to-end link
seamlessly connect customers located at traffic management as well as service aggregation.
different distances from the device. assurance capabilities, including
proactive service monitoring and fault OAM
MARKET SEGMENTS AND identification throughout the entire Featuring ultra fast, hardware-powered
APPLICATIONS network (see Figure 2). processing, ETX-205A performs OAM and
PM measurements in line rate with
ETX-205A is used in the following
ETHERNET maximum precision, offering the following
applications:
powerful benefits:
• Ethernet demarcation device – Classification
Traffic is mapped to the Ethernet flows • Immediate detection of loss of
ETX-205A separates the service
using very flexible classification criteria continuity (LOC), ensuring under 50 ms
provider network, the access provider
based on incoming port (port-based protection switching
network, and the customer network,
providing proactive service monitoring all-to-one bundling), VLAN ID, VLAN • Highly accurate frame loss
and easy fault localization for Ethernet priority, IP precedence, DSCP, Ethertype, measurements of live traffic
and pseudowire services throughout and IP/MAC source/destination address. • Flow-level (per CoS) monitoring,
the entire network (see Figure 1) Classification is defined for both VLAN enabling simultaneous processing of
tagged as well as untagged traffic. multiple OAM sessions with E-LAN and
E-Tree support
Layer-2 Control Processing
• Non-disruptive MAC and IP level
The device can be configured to pass
loopback testing of network integrity.
through Layer-2 control frames (including
other vendors’ L2CP frames, and with
Remote Office
GbE/FE Marketing
ETX-205A
4xE1/T1
Headquarters EVC1 Remote Office
PBX
GbE/FE GbE/FE
Marketing Marketing
GbE/FE
PBX Finance PBX
ETX-205A
4xE1/T1
PBX
Remote Office
Cellular Site
GbE/FE
NMS
Enb/IPNB
Aggregation Site
GbE/FE
STM-1/ ETX-205A
4xE1/T1
OC-3c
Cellular Site
STM-1/ PE PE
ETX-5300A/ GbE/FE
OC-3c
ETX-220A GbE/FE
BSC/RNC
Enb/IPNB
ETX-205A
4xE1/T1
BTS/Node B
Timing
SLA Assurance
Enhanced Traffic Management
Performance Management
Resiliency
Bandwidth 100/1000 Mbps per port, 100/1000 Mbps per port, 100/1000 Mbps per port
depending on license option depending on license option
Ethernet Ports Module/4 1/1/4 1/1/4
(net/net/user) SFP/copper combo SFP/copper SFP/copper combo
Network interface Network module: 2 × GbE, Up to 2 × GbE or FE SFP or copper Up to 2 × GbE or FE SFP/copper
4W SHDSL, or 8W SHDSL ports combo ports
User interface Up to 5 × GbE or FE SFP or copper Up to 5 × GbE or FE SFP or copper Up to 5 × GbE
ports ports SFP/copper combo ports
Number of flows 192/2/128 or 192/30/128, 192/2/128 or 192/30/128, 192/30/128
(EVC.cos) / shapers / depending on license option depending on license option
MEPs
Service type EPL and EVPL (flow-based) EPL and EVPL (flow-based) EPL and EVPL (flow-based)
Forwarding mode Flow-based Flow-based Flow-based
Bandwidth profile CIR/CBS, EIR/EBS per EVC.CoS CIR/CBS, EIR/EBS per EVC.CoS CIR/CBS, EIR/EBS per EVC.CoS
Max. frame size GbE uplink: 12,288 bytes 12,288 bytes 12,288 bytes
SHDSL uplink: 2,000 bytes
E1/T1, E3/T3, Via smart SFP, with integrated Via smart SFP, with integrated Via smart SFP, with integrated
OC-3/STM-1 bridging management management management
E1/T1 TDM pseudowire No No 4 E1/T1 interfaces
Timing options 1588v2 TC (Transparent Clock) 1588v2 TC (Transparent Clock) Synchronous Ethernet (SyncE),
1588v2 slave,
1588v2 TC (Transparent Clock)
Management interface Command line Command line Command line
Temperature-hardened No No Yes
option
Power supply AC or DC Universal AC/DC AC or DC
and the product names Optimux and IPmux, are registered trademarks of RAD Data Communications Ltd. All other trademarks are the property of their respective holders.
527-100-11/12 (4.3) Specifications are subject to change without prior notice. 2011–2013 RAD Data Communications Ltd. The RAD name, logo, logotype, and the terms EtherAccess, TDMoIP and TDMoIP Driven,
SPECIAL CONFIGURATIONS SUPPLIED ACCESSORIES
Ordering
ETX-205A/?/!/19/$/~ Power cord (one per power supply)
RECOMMENDED CONFIGURATIONS Legend RM-34
ETX-205A/AC/19 ? Enclosure type (Default=Regular Rack mount hardware kit for one unit
enclosure):
ETX-205A/AC/19/SYE CBL-RJ45/D9/F/6FT
H Industrially-hardened enclosure
ETX-205A/AC/19/PTP Control port cable with male RJ-45 and
Note: The ETX-205A/H version requires
female DB-9 connector
ETX-205A/AC/19/4E1T1 industrially-hardened SFP transceivers.