Professional Documents
Culture Documents
Logbook KAW
Logbook KAW
BESAR KAW
1. Menentukan daerah
2. Mencari data BPS 2023 (Mencari di 1 daerah)
3. Annual Report (Telkomsel)
4. Datasheet perangkat
5. Standarisasi (3GPP, IEEE)
1 . Kota Denpasar
2. Data diperoleh dari publikasi Kota Denpasar dalam angka, 2024 yang diterbitkan oleh BPS
• Data penduduk Kota Denpasar disetiap kecamatan
Denpasar Selatan : 188.998 Jiwa
Denpasar Timur : 182.422 Jiwa
Denpasar Barat : 120.826 Jiwa
Denpasar Utara : 168.738 Jiwa
Total : 660.984 Jiwa
• Kepadatan penduduk per km disetiap kecamatan
Denpasar Selatan : 3.778
Denpasar Timur : 7.035
Denpasar Barat : 5.150
Denpasar Utara : 6.322
Total : 5.247
• Laju pertumbuhan penduduk
2021-2022 : 0,02 %
• Tinggi wilayah (mdpl)
Denpasar Selatan : 00-12
Denpasar Timur : 00-75
Denpasar Barat : 00-75
Denpasar Utara : 00-75
. 3. Annual report Telkomsel data per 2022
Total Pelanggan : 156.812
Average Revenue Per User (ARPU) : 44 ribu rupiah
Total BTS 3G/4G/5G : 215.036 Unit
2
MINGGU KE 1
Tanggal: 16 Mei 2024
3
MINGGU KE 1
Tanggal: 16 Mei 2024
5. Standarisasi 3GPP
4G QOS PARAMETERS
Based on 3GPP TS 23.203
General
The service level (i.e., per SDF or per SDF aggregate) QoS parameters are QCI, ARP, GBR, and
MBR.
Each Service Data Flow (SDF) is associated with one and only one QoS Class Identifier (QCI). For
the same IP-CAN session multiple SDFs with the same QCI and ARP can be treated as a single
traffic aggregate which is referred to as a SDF aggregate. An SDF is a special case of an SDF
aggregate. The QCI is a scalar that is used as a reference to nodes specific parameters that control
packet forwarding treatment (e.g. scheduling weights, admission thresholds, queue management
thresholds, link layer protocol configuration, etc.) and that have been pre-configured by the operator
owning the node (e.g. eNodeB). When required by operator policy, the eNodeB can be configured
to also use the ARP priority level in addition to the QCI to control the packet forwarding treatment
in the eNodeB for SDFs having high priority ARPs.
4
MINGGU KE 1
Tanggal: 16 Mei 2024
The standardized characteristics are not signaled on any interface. They should be understood as
guidelines for the preconfiguration of node specific parameters for each QCI. The goal of
standardizing a QCI with corresponding characteristics is to ensure that applications / services are
mapped to that QCI receive the same minimum level of QoS in multi-vendor network deployments
and in the case of roaming. A standardized QCI and corresponding characteristics are independent
of the EU's current access (3GPP or Non-3GPP).
QCIs for which the Packet Error Loss Rate calculation includes those packets that were not delivered
within the Packet Delay Budget; and, it provides additional information on the Data Rate Averaging
Window as well as the Maximum Data Burst Volume that needs to be delivered within the Packet
Delay Budget.
5
MINGGU KE 1
Tanggal: 16 Mei 2024
6
MINGGU KE 1
Tanggal: 16 Mei 2024
7
MINGGU KE 1
Tanggal: 16 Mei 2024
8
MINGGU KE 1
Tanggal: 16 Mei 2024
9
10