Professional Documents
Culture Documents
Lunar Photography
Lunar Photography
REPORT
LUNAR ORBITER II
PHOTOGRAPHY
Prepared by
THE BOEING CO.
Seattle, Wash.
for Langley Research Center
LUNAR ORBITER II
PHOTOGRAPHY
For sale by the Clearinghouse for Federal Scientific and Technical Information
Springfield, Virginia 22151 - CFSTI price $3.00
CONTENTS
Section* Page No’s.
2.0 PHOTOGRAPHY 1
2.1 INTRODUCTION
2.3 PHOTOGRAPHS 8
2.3.1.1 Exposure 8
2.3.1.2 Processor-Dryer
. 2.3.1.3 Readout 1:
2.3.1.4 Reassembly 13
*
The section number 2 signifies only that this report is
the second in a series of numbered volumes submitted by the
contractor on the Lunar Orbiter II Project. Publication of the
complete series by NASA is not necessarily contemplated.
iii
CONTENTS
Page No’s.
2.6 CONCLUSIONS 97
iv
Figure No’s. ILLUSTRATIONS
Page No’s.
2.2-l: Primary-Site Distribution 5
2.3-l: Edge Data Gray Scale Calibration 9
2.3-2: Processing Mark Sources 10
2.3-3: Relative Locations of Processing Marks - Spacecraft 70-mm Film 11
V
Figure No’s. ILLUSTRATIONS Page Nob.
2.3-29: Sites IIP-lla and IIP-llb Coverage 39
vi
ILLUSTRATIONS
Figure No’s Page Soi.
2.5-11: Photo Quality Predict Program (QUAL) Output, Site IIP-9 91
2.5-20: White Level and Gray Scale Variation Readout Sequence 122 95
2.5-21: White Level and Gray Scale Variation Readout Sequence 127 95
vii
TABLES
viii
LUNARORBITERII
2.0 PHOTOGRAPHY
2.1 INTRODUCTION
This volume of the Lunar Orbiter Mission II Secondary objectives are to provide data re-
final report contains a description of mission garding the lunar environment, including ener-
photographic planning and conduct, and analy- getic radiation and meteoroid flux, and selen-
sis of the photographs. Data pertinent to analysis odesy and the Moon’s gravitational field by
and interpretation of the photographs are in- determination of spacecraft orbit characteristics
cluded. A functional description of the space- and perturbations.
craft photo subsystem and ground reconstruc-
tion is not included but may be found in Lunar 2.1.2 MISSION II OBJECTIVES
Orbiter Mission I Final Report, Boeing Docu-
ment D2-100727-2 (Volume II). However, The objectives of Mission II, as stated in NASA
changes made on the basis of Mission I results Document LOTD 147-1, are:
will be discussed. 0 Primary - To obtain, from lunar orbit,
detailed photographic information of vari-
Mission II was designed to provide data on ous lunar areas, to assess their suitability
sites located in the northern portion of the as landing sites for Apollo and Surveyor
Apollo landing zone. Because of the value of spacecraft, and to improve our knowledge
oblique photography for interpretation of lunar of the moon.
topography demonstrated on Mission I, addi- l Secondary - To provide precision trajec-
tional photographs of this type were scheduled tory information for use in improving the
and taken during Mission-II. definition of the lunar gravitational field.
l To provide measurements of micromete-
All scheduled photography was accomplished oroid flux and radiation dose in the lunar
and 98.5% of the planned coverage was read environment, primarily for spacecraft
out before failure of the traveling-wave-tube performance analysis.
amplifier (TWTA) to turn on terminated the
photographic phase of the mission. 2.1.3 PHOTOGRAPHIC MISSION SUMMARY
Injection of the spacecraft into the first ellipse
2.1.1 PROJECT OBJECTIVES was accomplished on November 10, 1966. Orbital
parameters were: apolune, 1871 km; perilune,
Lunar Orbiter’s primary objective is to provide 196.26 km; and inclination, 11.95 degrees. The
information necessary to locate sites that meet spacecraft was held in this ellipse for 22 orbits
the requirements for Apollo manned lunar land- to permit tracking and determination of orbital
ings. These requirements include the following: parameters. Photographs were not taken from
the first ellipse. Transfer to the second ellipse,
0 Certification of multiple sites providing having an initial perilune of 50.51 km, was suc-
for accessibility during different Apollo cessfully accomplished on November 15 at
launch windows and recycle times (at 22.52.42 GMT during Orbit 23. Following the
least 2 days between launch attempts and initial camera operations to move the film leader
three launch attempts each month); onto the takeup reel and photographic film into
l Location of areas - free of protuberances, the camera, photography was started over Site
depressions, or slopes constituting a haz- II P-l on November 18 at 15:24:53 GMT during
ard to landing - that are large enough to Orbit 52. Upon completion of photography,
accommodate LM guidance errors and Bimat was cut on November 26 (Day 330) at
maneuver capabilities; OS:58 GMT. All mission photography was ac-
0 The locations must be within the zone of complished from the second ellipse. Mission II
k5” latitude and+45” longitude. photography is summarized in Table 2.1-1.
1
I Table 2.1-1: Summary Of Mission II Photography
Numerical Summary
No. of Frames
Primary Sites Sites Exposed
Secondary Sites
Total 30 211
Area1 Coverage
Nearside Area
Telephoto 12,000 km 2
Farside Area
Total 3,000,OOO km 2 *
Multiple-frame sequences were exposed in the 10.2) depict target areas selected prior to flight.
fast mode to provide contiguous high-resolution All photographs taken to satisfy constraints on
coverage except for Site IIPS, where the camera time between camera operations and processing
axis was tilted to point at the target. The camera were planned as secondary sites of specific
axis was aligned for near-vertical photography targets.
at all primary sites. Single-frame oblique pho-
tography at four secondary sites produced photo- All photography planned for the mission was
graphs of.exceptional interest and value, as well successfully accomplished. After 98.5% of the
as including areas beyond the range of a vertical planned photography had been read out, failure
field of view. of the TWTA to turn on at 01:16 GMT Decem-
ber 7, 1966 terminated final readout of the
All Mission II photographs (except for Site IIS- photographs.
2
2.1.4 PHOTOGRAPHIC SUBSYSTEM DES- (in final assembly tests) to result in the
CFUPTION film not separating properly from the
Bimat, and both being pulled through the
A description of the Lunar Orbiter photographic diffusion channel toward Bimat takeup.
subsystems and their functions, together with To prevent such an occurrence:
the ground support equipment necessary for l)Tension on the Bimat supply drum
photographic reconstruction, has been included was increased;
in Lunar Orbiter Mission I Final Report, Volume 2) Diffusion channels were widened;
II. Discussion here will be limited to changes 3) Springs were added to the readout
made prior to Mission II that are pertinent to the looper to increase film tension.
photographic results, to significant factors spe- Addition of the springs to the readout
cific to Mission II, and to procedural changes in looper increased the possibility that the
preparation of the photographs. looper-empty encoder Gould stop in the
switch transition region, causing the com-
Problems encountered during Mission I pho- mand-control-and-program (CCP) circuit
tography and readout indicated the need for to act as an amplifier instead of a switch.
modification of the photographic subsystem to This could possibly result in:
improve photograph quality and reliability of 1) The supply brake failing to release;
operation. Changes pertinent to photography are 2) The supply motor stalling and caus-
summarized below; a detailed description of all ing the switch transistor to overheat
changes is included in the data package, com- and go into thermal runaway.
piling all premission testing that has been sub- A trigger circuit that will be either “on”
mitted to NASA. or “off’ was incorporated to compensate
l Changes were made in electrical and elec- for possible logic ambiguity that could re-
tronic circuitry to prevent incorrect opera- sult in the above operational anomalies.
tional timing of the focal-plane shutter l In Mission I, the optical-mechanical scan-
that had resulted in image smear in most ner, using the best state-of-the-art tech-
telephoto photographs of Mission I. These niques, introduced image distortion af-
changes reduced the susceptibility of the fecting image match between adjacent
shutter triggering circuit to spurious pulses framelets and precise stereo evaluation.
or other electromagnetic interference However, in Mission II, reseau marks pre-
(EMI). A filter was added to the 28-volt exposed on the spacecraft film permit
line to minimize the possibility of trigger- correction or compensation to be made to
ing other photographic subsystem circuits. metrical data. Details of these marks are
l The platen clamping spring tension was given in Paragraph 2.3.1.3.
increased to improve film clamping. This
change ensures that no motion of the film 2.1.5 CALIBRATION
relative to the platen occurs during the
exposure. It also improves flatness of the Tests and calibrations performed on the photo-
film in the lens focal plane to enhance graphic subsystem were essentially the same as
focus and resolution. those described in Volume II of the Mission I
l Following Bimat cut, tension on the film final report.
is reduced as the, processor continues to
run to clear the Bimat from the processor. Test and calibration data specific to the Mission
The reduced tension had been observed II subsystem has been submitted to NASA.
3
2.2 PHOTOGRAPHIC SITES
All photographic targets for Mission II were smoothest terrain, thus the most promising
scheduled prior to flight as either “primary areas for Lunar Module (LM) landing. Mission
sites” or “secondary sites.” Primary sites were II Primary Sites IIP-1, -7, -8, -9, -12, and -13 are
selected potential Apollo mission landing areas. within or contain areas of this terrain type. Areas
Selection of secondary sites was governed by of average mare are included in Primary Sites
two factors. IIP-3, -8, -9, and -11. The presence of ray struc-
l Scheduling of primary site photography ture is believed to correlate with surface rough-
established the orbits during which pho- ness. Primary Sites IIP-1, -3, -4, -8, -9, -10, -11,
tography was required by filmset and -12, and -13 include varying amounts and types
Bimat-stick constraints. of rays to provide additional data on the above
l The most desirable target from the stand- correlation. Mission I photographs showed evi-
point of obtaining supplementary terrain dence of volcanic-type formation, particularly
information or special scientific informa- Frame I-48M. This area was selected as Site
tion, such as photography of thermally IIP-2 for re-examination. Site IIP-9 also con-
anomalous locations. Oblique photog- tains positive relief features suggestive of vol-
raphy was included. canic origin. Evaluation of the area in southern
Mare Tranquillitatis photographed in Site I-3
No deviations from planned photographic sites showed it to be the smoothest area found on the
occurred during the mission except for Sec- first mission. Re-examination of this area was
ondary Site IIS-10.2. desired and thus designated as Site IIP-6. The
area of Ranger VIII impact was selected as Site
2.2.1 PRIMARY SITES IIP-5.
The criteria for selection of primary sites are The locations and albedos specified for the
detailed in Lunar Orbiter Mission II Descrip- primary sites are listed in Table 2.2-l. The
tion, NASA Document LOTD-107-1, October 26, albedo to be used in determining choice of
1966. Major criteria are summarized here for shutter speed for a site was selected to optimize
convenience. photography of the overall site or of the par-
l Zone of interest - Sites must lie within ticular area of interest within the planned
15” latitude and +45” longitude. coverage.
l Site characterisY&s - Sites must be
smooth enough for a lunar module land-
ing and with topographic features during 2.2.2 SECONDARY SITES
approach adequate for landing radar.
l Site locations - Longitude selections are
based upon Apollo launch considerations Targets selected as secondary sites are tabulated
requiring opportunities on alternate days in Table 2.2-2. Selection of the secondary sites
for each month of 1968. This requires that was constrained by availability of a suitable
sites be separated by 23 k 3” longitude. target within range on the designated orbit. Site
Selection is governed by Apollo perform- IIS- was originally planned as a westerly
ance constraints. Mission I provided pre- oblique of Sinus Medii with the camera axis
liminary data on the southern portion and within 4 degrees of the sunline to investigate
Mission II was planned to cover the north- terrain appearance with near-zero phase illum-
ern portion of the zone of interest. Addi- ination. Premission illumination studies to
tionall y, the Ranger VIII impact area ‘was predict exposure and signal-to-noise ratios for
to be photographed and certain Mission I the photography showed that the planned photo-
sites were to be re-examined. The primary- graph would grossly exceed exposure limita-
site locations and the approximate space- tions. The photograph could not be taken, how-
craft altitude during photography are ever, because photography with the vehicle 45
shown in Figure 2.2-l. degrees off sunline violated a photo-subsystem
power constraint.
Preliminary analysis of Mission I photographs
(refer to NASA Document LOTD-107-1) showed The albedos specified for each of the secondary
that the darker mare areas appeared to be the sites are listed in Table 2.2-3.
4
30” 15” OU 19 30° 45O
LONGITUDE (DEGREES)
ICl-l-t2
PHoTo 13
I
12
I
10 11
I
9
I
4 365 2 1
IJIlL 1 I I
f!;;i”97-8 I 91-21 85-61 W-90I d4 75-6 I 60I 58-9I 61
I 56I 51
I
5
Table 2.2-l: Primary-Site Locations and Albedos
Site Location Albedo
Latitude Longitude Maximum Minimum Selected
1IS-l 4”lO’N 36”SS.E blare Tran- 011 Following III’-1 as soon as possible. No intervening maneuvers.
quillitatis
IIS- 3’36% 36”25’E Site IIP-1 On Converging stereo for telephoto. Two four-frame sequences cen-
tered midway between Orbits 52 and 53. Three-axis maneuver.
IIS- sot 176”E Farside Off Vertical. Centered 20 decrees before PM tenninator. Roll
specified maneuver only.
IIS- sot 174”E Furside Off Northerly oblique. Horizon included in wide-angle frame.
specified
IIS- sot 158”E Farside Off Southerly oblique. Horizon included in wide-angle frame.
specified
IIS- 4”15’Y 4”30’E Triesnecker On Vertical. Three-axis maneuver.
IIS- O”05’N l”oo’w Flammarion Off Southerly oblique from point of closest approach. Three-‘axis
Herschel maneuver.
IIS- O”30’N 12”SO’E Sinus Medii On Vertical. North of Site I-4. Three-axis maneuver.
IIS- 2”2O’N O”30’E Sinus Medii On Vertical. Southwest OfTriesnecker. Northwest of Site IIP-7a.
Three-axis maneuver.
IIS-10.2 3”20’N ll”Oow Cambart C On Crater identified as a thermal anomaly.
IIS- 4”40’N 27w’W Copemican On Vertical. Three-axis maneuver.
l-d)'
Albedo
Site Maximum Minimum Selected
1; -
0.091 0.086 0.120
0.088
:; : 0.120 Note: No measurements were available for
0.137 far-side sites. Selected albedos are esti-
1; 0.158 6.120 0.092 mated. Maximum and minimum values are
0.139 not listed for limited near-side areas of near-
:; 6.147
0.137 6.137
0.098 0.105 uniform albedo or where data was uncer-
-10.2 0.092 tain.
-11 b.111 il.091 0.105
-12 0.120
-13 6.075 b.072 0.074
-14 - 0.120
-15 - 0.070
-16 - 0.072
-17 - 0.100
__.
7
2.3 PHOTOGRAPHS
Assessment and analysis of mission photography in the following paragraphs. Refer to Lunar
has been based upon second-generation copies Orbiter Mission I Final Report, Boeing Docu-
of the GRE 35-mm reconstructed record and ment D2-100727-2. Volume II. Paragraoh - A
2.2.1.1.
upon paper prints of reassembled photographs for discussion and description of those characl
prepared by NASA and by the Army Map Serv- teristics common to both missions.
ice. Assessment of photographic quality was
based principally upon the GRE film. All 35-mm 2.3.1.1 Exposure
reconstructed film could not be examined in
detail for analysis because of the amount of film Correction of or compensation for the difference
involved. A sampling technique was used. in light transmission between the telephoto
Frames at the start, middle, and end of each (610-mm) lens and the wide-angle (go-mm) lens
sequence of primary-site photographs were described in the Mission I final report, Volume
examined, and framelets near each end and the II, could not be completed in time for Mission
center of these frames were examined in detail. II. Therefore, the difference in exposure be-
tween telephoto and wide-angle photographs,
Because of the sensitometric characteristics of noted for Mission I, is present in those from
photographic paper emulsions and the various Mission II. At most primary sites, the telephoto
control techniques used in the photographic coverage was considered to be of greatest im-
printing processes involved, the prints were portance and shutter speeds were selected to
used only for assessing site coverage, to relate more nearly optimize these exposures. Because
the overall effects of gross topography and il- of the light transmission difference between the
lumination to photography, and to screen the two camera lenses, the expected consequence
photographs for processing anomalies. was overexposure of the wide-angle photo-
graphs. In some cases, the wide-angle coverage
was severely overexposed and the subsequent
2.3.1 GENERAL CHARACTERISTICS enhancement technique using an amplified
video tape input to the GRE was not adequate
to recover the photographic detail. In some
The telephoto and most of the wide-angle photo- cases, where overlapping coverage of a primary
graphs from Mission II are of good quality. In site was obtained on successive orbits, a dif-
many cases, however, the exposure used for a ferent exposure was used on each pass to more
site was selected to optimize telephoto cover- nearly optimize both telephoto and wide-angle
age at the expense of overexposure of the wide- coverage. Surface topography resulted in local-
angle photographs and resultant degradation of ized areas of extreme over- and under-exposure
their quality. The enhancement technique - in nearside photographs.
developed at Langley Research Center - in
which an amplified video tape record was used Quantitative determination of spacecraft film
as GRE input, was used successfully on many of density cannot be used as a measure of exposure
the overexposed wide-angle photographs. Reso- evaluation since direct measurement is impos-
lution requirements were met at all sites in sible. Determination of spacecraft film density
telephoto photographs, and in wide-angle photo- from the edge-data gray scale on the GRE film
graphs that were enhanced or not degraded by is difficult because each step in the reconstruc-
overexposure. tion - from spacecraft readout scanning through
production of the GRE film record or copy being
No major operational problems or failures af- used - must be considered and evaluated. The
fecting overall mission photography occurred. edge-data gray scale was calibrated using Bimat-
processed flight film during preflight testing at
Lunar Orbiter photographs exhibit certain .occa- ETR. The density readings are listed in Table
sional blemish characteristics, some of which, 2.3-l and the location of each step on the H&D
such as the processor stop and pull-off lines, are curve is shown in Figure 2.3-l. The densities
defects inherent in. the film processing system determined at ETR are ASA visual densities.
due to the start-and-stop processing require- The equivalent values in terms of readout den-
ments of the mission. The properties and charac- sity are listed in Table 2.3-l. Edge data densities
teristics of Mission II photographs are described have a tolerance of & 0.05.
8
tem and that are described and illustrated in the
Table 2.3-I:
Flight Film Edge Data Gray Scale Densities Mission I final report were present. A more de-
tailed discussion and description, reflecting
analysis of photographs from both missions,
ASA Visual Readout follows.
step No. Density Density
The increase in processing defects noticed in
0.35 0.29 Mission II over Mission I was largely attributable
i 0.37 0.31 to the increased number of times that the proces-
0.43 0.38 sor-dryer was stopped and started during this
: 0.50 0.45 mission. The defects were divided into two
0.65 0.62 groups - those expected due to processor stops
: 0.91 0.93 and those for which no explanation is presently
1.19 1.22 known. The expected defects as observed in
ii 1.49 1.34 (Estimated1 Missions I and II correspond to known dimen-
9 1.72 sions from the Bimat-film lamination point,
Figures 2.3-2 and 2.3-3. The other defects,
Most of the exposure evaluation of each site in “Queen Anne’s lace” or “freckles,” are as yet
subsequent paragraphs is based upon a visual unpredictable and are not really explained even
comparison of image density of a second-genera- though attempts to duplicate the phenomena
tion copy of GRE record with a calibrated 21- under controlled conditions have been per-
step gray scale. The determination is approxi- formed at Eastman Kodak Company.
mate. Evaluation of exposure, with respect to
over-, under-, or satisfactory, is largely sub- Subsequent to this flight, a procedure had been
jective. developed by which repetitive processing de-
fects would occur outside a few frames. For
More precise determination, using microden- subsequent missions, certain frames or photo-
sitometer measurements, has been made on a graphs would be defined as critical for a given
limited number of framelets from some sites. mission so that mission planning and conduct
This evaluation has shown that the noise pattern could proceed accordingly to eliminate or at
of the photographs, described in Mission I final least minimize the possibility of a blemish in a
report, Volume II, Paragraph 2.2.1.1, is such that critical area to be photographed.
it is the limiting factor in resolution. The
presence of detail equivalent to 100 microns on
the GRE film (nominal system resolution),
where the image is of moderate contrast, could
not be distinguished from the noise on the trace
from a microdensitometer employing a lo-
micron aperture. On the other hand, an experi-
enced observer frequently could recognize, with
some assurance, small features in the size range
of the noise pattern on the GRE film by visual
examination at a magnification of about 10 di-
ameters. Such recognition became more sure
where contrasts were higher. It has been found
that detection of very small surface detail ap-
peared to be related to the type of terrain pho-
tographed. This is evident particularly in rock-
strewn areas near craters where much fine detail
is expected.
No anomalies or operational failures of either
shutter affecting mission photography were
noted. 5.5 i.0 i.5 0.0 0.5
2.3.1.2 Processor-Dryer LOG. EXPOSURE (MCS)
Processing defects that are inherent in the sys- Figure 2.3-l: Edge Data Gray Scale Calibration
9
/
I
\ I / \
FkWe 2.3-z:
p
rocessingM ar lc sources
10
Bimat Pull-Off Line Stop Line
“Snake Eyes”
Film Exposure Direction Double Line
Forward - 1
7 1
’ !
’ I
’ I
) \
\#o-;--
. e
r-
Pull-Off Line Position Dependent on
Bimat Supply Reel Content (Diameter)
11
stop line, and follow it by about 4.2 Avoidance of Processing Defects in “High-
inches. Pressure of the Bimat cut encoder Value Frames”
roller on the back of the Bimat forces the
emulsion against the cutout area edges of There are no known changes to present operat-
the conductivity roller during the proces- ing techniques that will reduce the number of
sor-off time. Because the size and degra- defects when the mission is programmed with
dation of this condition seems to vary with photos and processing spread out through so
processor-off time, no known solution is many orbits.
available other than continuous process- l Freckles or lace appearance cannot be
ing. This condition does not always ap- predicted; however, they seem to be as-
pear following a processor-off period. sociated with the Bimat stop line. It is
hopefully believed that longer processing-
l Longitudinal Lines on time would help minimize their occur-
Two, three, or four longitudinal lines of rence.
varying density are present at times on l The quality of processing has not shown
the film. Tests have been made to deter- obvious degradation at the end of the
mine the cause of the streaks. It was found processing period; therefore, it is believed
that, as the film passed into the camera that no improvement would be possible
storage looper, a static charge was gener- by shortening the time to completion of
ated when the film rubbed against the processing.
first teflon separator in the looper end. l Priority rea.dout to the extent used in
The streaks were caused by static dis- Mission II does not seem to affect process-
charge onto the film, which produced ing quality.
localized fogging. The separator has been l The practice of processing at least two
relocated and covered with aluminized frames every 4 hours or each orbit as a
mylar tape to correct this problem in minimum is still recommended. Fewer
photo subsystems for missions following defects would be present if more frames
Mission III. were processed at one time.
l Bimat emulsion peeling or failure of the
film and Bimat to delaminate has not been
l “Freckles” or “Queen Anne’s Lace” noted.
This appears as a spotted area of unpro-
cessed film arranged in a random manner. 2.3.1.3 Readout
The areas vary in size and location on the
film and do not follow any repeating pat- Small marks that may have originated at the
tern. No known reason for these defects readout section appear as a repeating pattern at
has been found; they could be attributed and near the edge of each framelet. The occur-
to bubbles in the Bimat, an unknown re- rence of these thin, scratch-like marks was found
action of an area of the Bimat, or process- to increase as readout progressed. Accumulation
ing characteristics when the tension of the of Bimat or film elusion particles at the readout
film and Bimat is varied due to the fre- gate has been suggested as a possible cause.
quent starting and stopping of the proces- Similar marks were observed on Mission I pho-
sor-dryer. At present there is no known tographs.
way to prevent this condition.
Longitudinal density variations within the
A significant area of defective processing occurs framelets, due to the halo effect described in
between wide-angle Frames 99 and 102. The the Mission I final report, were prevented by
defects appear as lace-like loops and spots as GRE masking. Transverse density variations
shown in Figure 2.2-4 of the Lunar Orbiter Mis- were controlled by control of the line-scan-
sion I final report, Volume II. Telephoto Frame tube focus.
215 is also affected to some extent by this prob-
lem. Processing defects of minor extent occur The noise pattern, described in the Mission I
occasionally throughout mission photography. final report, was present in the Mission II GRE
Also noted in the area of Frames 99 to 102 was film. The cause of this pattern has not been es-
an effect similar in appearance to the noise pat- tablished conclusively.
tern but of a much larger scale. This pattern is
believed to be due to the same cause as the Some variations in readout film advance oc-
“lace” effect but not as intense. curred. This effect occasionally resulted in a
12
small amount of incorrect overlap of adjacent techniques were used in the photographic print-
framelets. In one case, during priority readout ing process to enhance print quality by both
sequence 052, a temporary failure of film ad- agencies. For example, LogEtronics printers
vance resulted in one framelet (769) being read were used to compensate for large density varia-
out 18 times. No other similar occurrence was tions within the photographs and thus produce
noted. prints more easily interpreted. Printing control
also compensated for density differences be-
Nonlinearity of the optical-mechanical scanner tween wide-angle and telephoto pictures to
was present. However, reference (“reseau”) produce greater similarity in appearance of the
marks in the form of small crosses, illustrated in two types of photographs. While these control
Figure 2.3-4, have been included. These reseau techniques do not increase the information con-
marks were exposed on the spacecraft film at the tent of the photography, they do increase the
time the edge data was pre-exposed, and thus information within the prints by effectively low-
occur in a fixed relationship to the edge data ering the density range capability inherent in
format. Any dimensional changes subsequent to the film to more nearly match the range capabil-
imaging by the spacecraft cameras, including ity of the paper.
readout, can be determined and corrections made.
The video tape enhancement technique also was
used by Langley Research Center to prepare
2.54-j f.-
prints of overexposed wide-angle photographs.
Photographic detail was retrieved that was ob-
6.3L, ,.-
scured by the high image density of the space-
craft negative and corresponding low video
signal. However, information loss occurred in
some darker or shadowed areas of such photo-
graphic prints.
OTLVT 0.100-1
-I bo . 015
all wide-angle
The reassembly
Company was
photographs were reassembled
but, where done, the full frame was reassembled
as a single photograph rather than as subframes.
13
Thirteen primary sites were planned. Analysis used in preparing the film being examined. This
of the photographic coverage of Mission I sites criterion also is independent of the spacecraft
indicated the desirability of modifying the pre- altitude at the time of photography, as opposed
viously selected sites for Mission II area cover- to actual ground measure. For these reasons,
age. Site IIP-1 was photographed by a single 16- resolution has been estimated and reported in
frame sequence; Sites HP-S, -4, -5, and -9 were the following discussions largely in these terms.
photographed by single 8-frame sequences; for
Sites IIP-8, three eight-frame sequences on suc- The resolution requirement for Lunar Orbiter
cessive orbits were used. The remaining seven photography has been stated as that necessary
primary sites were photographed by two eight- to detect a l-meter object with the telephoto lens
frame sequences on successive orbits. Photo- and an 8-meter object with the wide-angle lens
graphic parameters for primary sites are summar- from an altitude of 46 kilometers. This requires
ized in Table 2.3-2. Site-dependent characteris- a resolution of 76 lines per millimeter on the
tics of photography are discussed in the following spacecraft film or ,lO lines per millimeter on the
paragraphs. 35-mm GRE reconstructed record. There are
approximately 40 scan lines per millimeter on
In the evaluation of mission photographic reso- the GRE record. Thus, the resolution require-
lution. the scan lines Provide a convenient lmit ment is eauivalent
A to detection of obiects
s whose
of measure independent of copying processes images span four scan lines.
14
I
/ I “f”r t I
36’ 370 38’ 39O
EAST LONGITUDE
Figure 2.3-5: Site IIP-1 Coverage
Since ground resolution is directly proportional in following figures showing site coverage. This
to the spacecraft altitude (or slant distance), it is marks the point location specified by NASA as
related to scan lines by the expression: the site target and used in mission planning. The
obtained mission photographic coverage is not
Ground resolution in meters NH always centered on this position because of op-
= -x -
4 46 erational limitations. The closest orbit did not
always pass directly over the position, and addi-
tional factors such as timing of the initial ex-
where N is the number of scan lines spanned by posure of a sequence, variations in spacecraft
the smallest objects detected, and H is the space- attitude and altitude, uncertainities in predicted
craft altitude in kilometers. (This applies to the orbital parameters, and chart errors contribute
telephoto coverage; wide-angle resolution must to the apparent offset. Failure of the TWTA ter-
be increased by a factor of 8.) minated final readout before the last eight frames
had been read out. Portions of this site photog-
2.3.2.1 Site IIP-1 raphy read out in priority mode included some
frames not reached in final readout. Although
Coverage of Site IIP-1,4”10’N latitude, 36O55’E three complete wide-angle frames were not read
longitude, is shown in Figure 2.3-5. Note that out (Frames 6, 8, and lo), the other frames com-
the “specified target” is shown in this figure and pletely overlap their coverage. Therefore, wide-
angle coverage is complete. Lack of telephoto white-light transmission than the telephoto lens.
frame overlap resulted in loss of coverage of It should be noted here that GRE positive 35-
most of six and all of two telephoto frames. The mm film offers the most direct means of evaluat-
area for which no telephoto coverage was ob- ing the suitability of spacecraft 70-mm film ex-
tained is illustrated by shading in Figure 2.3-6. posures. The correctness of photo system exposure
times is especially difficult to evaluate from re-
assembled positive prints on opaque materials
The predicted exposure of 0.04 second appears because of the many additional variables intro-
to be satisfactory for both wide-angle and tele- duced in the various printing processes and the
photo photographs of the mare area of this site. nature of the medium. Positive transparencies
Inspection of second-generation ground recon- viewed by transmitted light can present an
struction electronics (GRE) positive 35-mm film image with a greater contrast range and better
indicated that the wide-angle frames had ex- definition than opaque positive viewed by re-
posures ranging from good to overexposed, flected light. An example of Site HP-1 wide-
while the corresponding telephoto frames tended angle photography is shown in Figure 2.3-7. In
towards underexposure. This difference in this figure and subsequent photographic illus-
average image densities was anticipated since trations, the complete frame is not necessarily
the photo subsystem wide-angle lens has greater reproduced.
TWTA Failure
1 5 1 6 1 7 1 8 1 9 1 10 1 II 1 12 1 13 1 14 ( 15 1 16 1 17 1 18 1 19 1 20 1
FRAME NUMBER
16
‘. .1 ‘. ) ; :: , -:.
. ?.‘T. ..,
. .---
17
32’ 33O 34O 35O 36’
EAST LONGITUDE
This site, shown in Figure 2.3-S and 2.3-9, is Wide-angle photographs show the circular dome
located at the southern boundary of Mare Tran- structure in the south-central portion, although
quillitatis about 100 kilometers east of Maskelyne. it is barely discernible as a luminance change
Portrayal on ACIC charts LAC 61, Taruntius, resulting from the small slope change. The wide-
and AC1 61D, Maskelyne D, shows a few craters angle photographs show excellent detail through-
1 to 2 km in diameter and low dome structures out, indicating that the shutter speed of 0.02
in the central and eastern portion of the area. second was satisfactory. The telephoto frames
The entire area is depicted as flat or low-relief are somewhat underexposed as judged by the
mare. GRE film. However, the underexposure does
not appear to have resulted in loss of image de-
Correlation of aeral coverage in the photographs tail. Craters spanning three and one half to four
with the computed corners was difficult because scan lines were detected, indicating acceptable
of the limited number of well-defined features resolution. Prints of telephoto frames prepared
on the charts that could reliably be identified in by the Army Map Service show very good de-
the photographs. Some uncertainty exists with tail and little apparent loss of information.
18
.
’ .
19
c---
23O 22O 21° 2o” 19O
EAST LONGITUDE
This site, Figure 2.3-10, is south of Arago and Exposure of the wide-angle frames appeared to
east of Manners, in western Mare Tranquillitatis. be slightly more than for Site IIP-2 but not ex-
The mare area of the site shown on AIC 6OC, cessive. The telephoto frames were exposed
Arago, and in Figure 2.3-11, includes a prom- somewhat less than desirable, which indicates
inent fan-shaped rille system extending south that selection of 0.04 second was correct. Prints
from Arago and a system of low ridges associated of both wide-angle and telephoto frames were of
with the premare crater Lamont. Arago C, 3.5 good quality, showing detail in all areas except
kilometers in diameter, is the only named fea- hard shadows or brightly illuminated slopes
ture within the area photographed by the two facing the Sun.
eight-frame sequences.
Examination of GRE film showed many craters
Since the site was photographed on two succes- and features spanning three or four scan lines,
sive orbits with eight-frame sequences in the equivalent to the required system resolution.
fast mode, both forward and side overlap is pro- Resolution capability of the system is shown
vided for stereo examination of the wide-angle dramatically in the rock-strewn summit of the
coverage. Side overlap of the telephoto expo- prominent ridge and several craters included in
sures permits stereo examination of a limited the telephoto frames of the eastern portion of
area at high resolution. The amount of side over- the area (Figure 2.3-12).
20
,
.,.,, ’ “, 9’
jl , ., L . ( ‘,I ’
\ .- 9 .( : ; TC’ :?‘,
j. ,,; ,I .- ,..
‘, .,
‘
*I ._
21
Figure 2.3-12: Telephoto Photography of Site IIP-3a
22
14O 15O 16’ 18O
EAST LONGITUDE
23
II
Figure 2.3-14: Wide-Angle Photography of Site IIP-4
24
23O 24O 25’ 26O 27O
EAST LONGITUDE
2.3.2.5 Site IIP-5 The shutter speed of 0.04 second used at this
site was the correct choice. Wide-angle frames
Site HP-5 was positioned to include the impact are exposed slightly more than optimum, while
point of Ranger VIII in Mare Tranquillitatis. The the telephoto frames are slightly underexposed.
area was photographed by a single eight-frame Image density for apparently smooth and level
sequence. areas was estimated to be 0.7 to 0.8 in wide-
angle photographs and 0.9 to 1.0 in telephoto
The photographic coverage computed from post- frames as determined from GRE film. These
mission data is shown in Figure 2.3-15. Location values correspond to 0.8 to 0.9 and 0.6 to 0.7,
of the southwest corner of the photographic respectively, on the spacecraft film. The photog-
coverage was determined to be 23” 38.0’ E raphy is represented by a portion of Wide-Angle
longitude, 2” 21.0’ N latitude by comparison of and Telephoto Frame 70, Figures 2.3-16 and
Wide-Angle Frame 67 with the ACIC chart 2.3-17, respectively.
Sabine DM, RLC9 having a scale of 1:50,000.
Charts of this series do not include all of the Resolution of the wide-angle photographs was
area photographed at this site and AIC 60-C equivalent to four scan lines near the frame
Arago, does not include sufficient data to permit center. Telephoto frames were found to resolve
location of the remaining corners. features spanning four to five scan lines.
25
Figure 2.3-16: Wide-Angle Photography of Site IIP-5, Frame 70
26
,
‘.B
..I
..:. 0
‘; ,,
+/ ‘, I:
..,,a ,
. .
:
.’ ,,..
: ..‘,
.:
I ;.. : ,
,‘,( ,.‘.
.,
27
22O 23’ 24O 25O 26’
EAST LONGlTUDE
The impact point of Ranger VIII has been iden- frame sequences on successive passes, provid-
tified on Telephoto Frame 70 as one of two ing the coverage shown in Figure 2.3-18. The
small, bright craters. The craters have diameters area is south of Site IIP-5 and includes the west-
of approximately 7 and 15 meters, lie close to em portion of the area photographed as Site I-3
the projected trajectory track, and have the on Mission I. The entire area is level mare,
appearance of recent formation. Since Ranger with crater Sabine E, 5 kilometers in diameter,
VIII did not photograph its impact point, posi- the largest topographic feature. Computed posi-
tive identification of the crater by comparison tions of photograph corners agree within about
of small photographic detail obtained by the 2 to 3 km of positions determined by comparison
two spacecraft cannot be made. However, of the photographs with Ranger VIII charts
results of impact studies by USGS geologists (RLC 7, Sabine).
and others indicate the smaller of the two
craters is the most likely candidate for the The quality of site photographs was good to
Ranger VIII impact point. The location of the fair based upon a subjective assessment of the
craters is indicated on Figures 2.3-16 and 2.3-17. GRE film. The relatively small phase angle
(61.1 to 62.6 degrees), together with the smooth
2.3.2.6 Site IIP-6 mare surface of the site, resulted in photographs
that lack pronounced contrasts, although surface
Site IIP-6 was photographed with two eight- detail is shown (Figure 2.3-19).
28
,
1
*
* . ’
.
:
L
29
3O 2O lo O0
30
-. _--_ --_ -_
b ’ . l
.. t 4
I
,* I. . . .
:.!l’,r;:?* ,,..,$ !.-.!;
,?‘Y)’ : j, ‘(
.
31
---- .-
----
.. ;:_.
3” 2O lo O0
WEST LONGITUDE
32
--.-.-. ___
.’ ’ *
.
:.. ,
8 . -
4 ,
.. P ;y,‘: 4‘-.’
, .I ’ ;.:.
t
33
34
15O 14O 13O 12O 11°
WEST LONGITUDE
2.3.2.9 Site IIP-9 fairly good exposures for the wide-angle photo-
graphs, with a tendency towards overexposure
Site HP-9 is located in mare east of Gambart (average GRE density 0.6) and loss of detail
as shown in Figure 2.3-25. The area includes in the midportion of each frame. Surface fea-
some low-relief, upland-type of terrain but no tures spanning only three to four scan lines were
major topographic features. The area is within detected near the center of the wide-angle
the influence of the Copernican ray system and frames, although some detail was lost in high-
thus has a relatively high albedo for mare (0.093). light areas (Figure 2.3-26).
Comparison of the wide-angle photographs with
the ACIC lunar charts of both the LAC and AIC
series (LAC 58, Copernicus, Second Edition, As expected from the differences in lens trans-
and AIC 58C, Gambart) shows differences in mission characteristics, the telephoto frames
feature positions. These differences introduce tended to be underexposed. Although the
uncertainty in location of actual photographic average GRE image density was high, lunar
coverage on the above charts. features spanning three and one half to four
scan lines were observed on the telephoto
The shutter speed of 0.02 second resulted in frames.
35
Figure 2.3-26: Wide-Angle Photography of Site IIP-9
36
29’ 28O 270 26O 25O
WEST LONGlTUDE
2.3.2.10 Site UP-10 The shutter speed of 0.04 second was correct
for this site. Both wide-angle and telephoto
frames were of good quality although the latter
Site IIP-10 was photographed with two eight- were exposed less than optimum. Since there
frame sequences on successive orbits to pro- are no large areas of steep slopes, information
vide coverage as shown in Figure 2.3-27. The loss from hard shadows or very bright high-
site, west of Reinhold, is depicted on ACIC lighted areas is minimal.
Chart AIC 58 D, Reinhold, as smooth mare with
faint ridges and few craters. Copemican rays Wide-angle frames of the first sequence appear-
occur within the area. The ridges and dome ed to be of higher quality than those of most
indicated on the charts were not readily ap- prior sites. Telephoto frames were also of good
parent in the wide-angle photographs, although quality, although the average GRE film density
the sun angle was 78 degrees. Presence of ray tended to be greater than for the wide-angle
structure was evident more from crater distri- photos. Features identified as craters spanning
bution or surface structure than from a differ- only three scan lines (0.08 mm on the GRE
ence in luminance, although some indication film) were detected in both wide-angle and
of the latter is visible. (Figure 2.3-28). telephoto frames of this site.
37 I
:
Figure 2.3-28: Wide-Angle Photography of Site IIP-1Oa
38
22O 21° 2o” 19O 18’
WEST LONGITUDE
39
.
-= ---
_.-._
40
‘,
:.:.
_.
,j: ,.
:
,.
:.,
41
32’ 33O 34O 33O 32’
WEST LONGITUDE
The relatively small angle of incidence of the A shutter speed of 0.04 second was used for
illumination (59 to 62 degrees) existing at this the photographs taken on the first of the two
site during photography was an important factor eight-frame sequences at this site, and a speed
in reducing the quality of wide-angle photog- of 0.02 second for the second sequence. The
raphy by lowering contrasts. computations for exposure prediction indicated
a borderline condition between 0.04 and 0.02
2.3.2.12 Site IIP-12 second. Considering the forward and side over-
lap obtained by the two sequences pIanned, an
This site is southeast of Kepler in an area indi- exposure of 0.04 second was selected for the
cated on the ACIC charts as smooth, almost first sequence to provide better exposure of
featureless, mare, as shown in Figure 2.3-32. the telephoto frames at the expense of overexpo-
The area does, however, include ray structure sure of the wide-angle frames. The 0.02-second
originating from both Kepler and Copernicus. shutter speed was used for the second pass for
The wide-angle photographs show few top- improved exposure of the wide-angle frames.
ographic features, either craters or eminences,
larger than 1.5 kilometers in diameter. There Telephoto frame exposure of the first pass (IIP-
is, on the other hand, much evidence of secon- 12a) appears to be very good. Since there are
dary craters and ejecta patterns whose align- no major topographic features, surface detail
ment indicates origin from Kepler and Coperni- is lost only within the areas of hard shadows and
cus (Figure 2.3-33). highlighted slopes within steep-walled craters.
42
, . , , , \ I L.
i7-f b ,’ ; ;’ _. ., ,‘,;., ,,,,’ . ‘-’ ,,‘. .: , .. ‘. .‘,.‘*! ‘I’,
WEST LONGITUDE
Albedo variations associated with ray structures away from the Sun. Because this area appears
are apparent but do not cause a luminance range to be rough as a result of a high density of old
beyond system capability. rounded craters and mounds, the underexpo-
sure seems to be accentuated (Figure 2.3-34).
Most wide-angle frames of the first pass are
quite overexposed and show little surface de- Resolution and feature detection was compar-
tail except hard, or nearly hard, shadows. Small able with previous sites, although degraded at
craters can be detected by these shadows, but the exposure extremes.
the crater diameter is uncertain.
45
-._- -___--_-_-~ ..--- .-r.-__ -. -...-._ - --.- -__r_ __-.. --- _______. .~ - -L._.-..-
Figure 2.3-36: Telephoto Photography of Site IIP-13a
46
Figure 2.3-37: Wide-Angle Photography of Site IIP-13a
47
Figure 2.3-38: Telephoto Photography of Site IIP-13b
48
I -- -
The site was photographed with eight-frame with the primary site. The first frame was ex-
sequences on two successive orbits. As for the posed 48.3 seconds following the last frame of
previous site, a shutter speed of 0.04 second Site IIP-1. The delay resulted in a separation
was used for IIP13-a and 0.02 second for of 61 kilometers between areas photographed.
IIP13-b. Photographic parameters were unchanged from
those used for the primary site, except for the
For the first sequence (IIP-13a), the O.OPsecond number of frames exposed.
shutter speed resulted in good telephoto ex-
posures and generally overexposed wide-angle 2.3.3.2 Site IIS-
photographs. Some surface detail was lost in
the wide-angle frames. Craters spanning as Two sequences of four frames were exposed on
few as three scan lines could be discerned occa- two successive orbits. In each case, spacecraft
sionally on the GRE film but the actual dimen- attitude was controlled to position the track of
sions were difficult to establish because of the the camera axis midway between the nadir of
lack of detail. Craters spanning as few as three the two orbits. The purpose was to investigate
scan lines could be discerned in the midportions the feasibility of convergent stereo photography
of the telephoto frames (Figure 2.3-36). by the telephoto lens. The shutter speed was
changed from 0.04 second used on the first
The O.O2-second shutter speed used for the sequence to 0.02 second for the second pass.
second eight-frame sequence (IIP-13b) resulted This change was necessary because of the
in good exposures for the wide-angle frames change in surface luminance resulting from the
(Figure 2.3-37) and considerable underexposure different phase angle for each spacecraft atti-
of the telephoto frames (Figure 2.3-38). Esti- tude.
mated resolutions for the central areas of the
wide-angle and telephoto frames were three An analysis of the stereometric potential of
scan lines and four scan lines, respectively. the photographs was made by the Aeronautical
Chart and Information Center. The results of
2.3.3 SECONDARY-SITE PHOTOGRAPHY the study, as reported in Preliminary Geologic
Evaluation and Apollo Landing Analysis of
Seventeen secondary sites were selected for Areas Photographed by Lunar Orbiter II,
photography in mission planning, all of which Langley Working Paper LWP-363, NASA Lang-
was accomplished successfully. These sites ley Research Center, March 1967, are quoted
were chosen to provide information supple- below.
menting primary site photography, and to ob- “a. A spot-heighting test achieved a stand-
tain data of special scientific interest concern- ard deviation (vertical) of 0.7 meter at
ing features or areas not included in primary random reseau intersections. A standard
sites. Site IIS- was photographed by a sequence deviation of 0.46 meter was achieved at
of four frames, and Site IIS- by sequences of well-defined, high-contrast feature
four frames on two successive orbits. The re- points.
maining 15 sites were each photographed by
a single frame. Photographic parameters are b. Two-meter relative contours were drawn
included in the photographic supporting data, over a small area of the model. A repeat-
Table 2.4-4. The secondary sites are summarized ability test was made by drawing con-
in Table 2.3-3. tours over the same area a number of
times.
Although these areas are considered secondary
in importance to the primary mission objectives, C. As a result of the test, it is estimated that
many of the photographs provide significant relative elevations of control points
scientific information and are of outstanding could be computed with a standard
general interest. This is because of the oppor- deviation of about 1 meter on high-
tunity to select, within certain limitations, areas resolution convergent exposures of this
or features of special interest or to employ an type.”
oblique line of sight.
2.3.3.3 Farside Photographs
2.3.3.1 Site IIS-
Four secondary sites were located on the lunar
This site is, in effect, an extension of Site farside: Sites IIS-3, -4, -5, and -14. Each was
IIP-1, although the coverage is not contiguous taken from a high altitude (1453, 1450, 1466,
49
Table 2.3-3: Mission II Secondary Sites
I Site Latitude
Location
I Longitude
Frame
Number(s)
Target
r- IIS-2a
IIS-2b
IIS-
3” 36’ N
1
36” 75’ E
176” E
T 25-28
33
Convergent telephoto stereo experiment. Area in south Mare
Tranquillitatis.
Farside
Vicinity of Missidn I Frame I-42
IIS- 2” 20’ N 0” 30’ E 95 Sinus Medii S.W. of Triesnecker. N.W. of Site IIP-7a
L
IIS-10.2 3” 20’ N ll”5O’W 112 Gambart C. Thermal anomaly
IIS- 3” 20’ N 43” 50’ w 195 Braided ridge. Mare S.W. of Kepler
IIS- 7” 25’ N 59” 00’ w 215 Bright ray structure west of Reiner. Oblique
and 1496 kilometers, respectively). Because of slant distance to the surface within the field of
the wide coverage obtained at these altitudes, view, proper image-motion compensation could
and the resulting extreme range of surface illum- not be obtained throughout. Unavoidable smear
ination within the field of view, the median of the image in the near foreground is present,
shutter speed of 0.02 second was used. Mission decreasing in amount with increasing distance
I farside photography also had shown that this to the surface. Image smear appeared most
exposure produced acceptable results. The pronounced in Frames 213 and 215. Litile smear
farside photographs obtained on Mission II is apparent in the telephoto picture of Coperni-
were of good quality. In most wide-angle frames, cus (Frame 162, Figure 2.3-43). The amount of
the exposure ranged from underexposure toward image smear in these photographs is depen-
the terminator side to overexposure on the op- dent upon the shutter speed used. Frame 162
posite side as expected. The intermediate area was exposed with a shutter speed of 0.01
was, however, of very good quality. Although second, Frame 93 at 0.02 second, and Frames
the telephoto frames were exposed less than 213 and 215 were exposed at 0.04 second.
the wide-angle due to the lens characteristics,
good quality photographs were obtained. It should be noted that, in the case of these
Examples of the wide-angle and telephoto oblique photographs in which the field of
photography from Frame 75 of Site IIS- are view includes the lunar horizon, the computed
shown in Figures 2.3-39 and 2.3-40. coordinates of the corner positions are not valid.
Where a corner does not lie on the surface, the
Resolution of the farside photographs, in terms computer program beaks down, and none of the
of scan lines, was comparable with the general four corner positions are correct. Coverage in
mission photography although some loss these cases is most readily obtained by direct
occured near the sides of wide-angle frames due comparison of the photographs with the ACIC
to the extreme luminance range. lunar charts.
51
Figure 2.3-39: Wide-Angle Photography of Farside, Site IIS-
52
Figure 2.3-40: Telephoto Photography of Farside Site IIS-
53
Figure 2.3-41: Oblique Wide-Angle Photography, Copernicus, Site IIS-
54
Figure 2.3-42: Oblique Wide-Angle Photography, Marius, Site IIS-
Figure 2.3-43: Oblique Telephoto Photography, Copernicus, Site IIS-
56
2.4 PHOTOGRAPHIC SUPPORTING DATA
Interpretation and evaluation of the lunar photo- When a secondary site could be included in a
graphs requires specifFd;f;imation regarding data arc, this was done. Three additional OD
spacecraft position, ’ altitude, and solutions were computed for secondary sites.
velocity at the time each pi&ure was taken. The site determinations were obtained by solv-
Computer programs (photo and ,evaluation) ing only for the state vector (X, Y, Z, X, Y, Z) and
were developed that combined prediction re- using values of the LRC harmonic coefficients
quirements for photo mission control, with post- specified in Appendix B of Volume VI.
mission data requirements. Figure 2.4-l illus-
trates the relationship between trajectory and The postflight orbit determination solutions
spacecraft performance parameters required to and their relation to photographic sites are listed
compute the supporting data. Postmission photo- in Table 2.4-l. Under “OD Solution” are serial
graphic data computations were made at the numbers of the programs assigned by the orbit
SFOF shortly after completion of the mission. determination (OD) group.
Input data were obtained primarily from post- Camera-on times were obtained by reading the
flight analysis of the doppler tracking data using digital time code exposed on the spacecraft film
the SPAC computer program ODPL, post- when the 80-mm shutter actuated. A computer
mission evaluation of the spacecraft attitude, routine (TIML) was developed and used to con-
and time of exposure as read from the GRE vert the spacecraft time, contained at the start of
film. each telemetry frame, to the correct time and
provide a tabulation of significant parameters at
2.4.1.1 Spacecraft Position and Velocity IO-minute intervals during any specified period.
The digital format was converted to decimal
Postflight orbit determination defined space- values for entry into the TIML tabulations and
craft position and velocity just prior to the first the GMT time of exposure determined.
commanded camera-on time of the sequence
for primary site photos. In all cases, data from 2.4.1.3 Spacecraft Attitude
at least two orbits prior to the site orbit and at
least one orbit after the site orbit were used in The roll, pitch, and yaw maneuver angles shown
these calculations. in Table 2.4-2 were used to describe the attitude
INPUTS OUTPUTS
57
Table 2.4-l: Orbit Determination Solutions Table 2.4-2: Photographic Maneuver Angles
Site Frame OD
Numbers Solution Site Maneuver Angles (degrees)
Roll Yaw Pitch
IIP-1 5-20 9016 IIP-1 5.24 9.25 2.81
IIS- 21-24 9016 IIS- 5.24 9.25 2.81
IIS-2a 25-28 9016 IIS-2a -1.47 6.93 11.12
IIS-2b 29-32 9016 IIS-2b 12.17 11.70 -8.40
IIS- 33 9016 IIS- -178.00 0.00 0.00
IIS- 34 9004 IIS- 164.00 0.00 0.00
IIP-2 35-42 9006 IIP-2 5.30 9.50 -2.40
IIP-3a 43-50 9007A IIP-3a 5.33 9.50 5.45
IIP-3b 51-58 9007B IIP-3b .5.33 9.56 4.25
IIP-4 59-66 9008 IIP-4 5.33 9.57 7.61
IIP-5 67-74 9009 IIP-5 8.66 10.82 -1.25
IIS- 9005 IIS- -165.00 0.00 0.00
IIP-6a %-83 9015A IIP-6a 5.38 9.62 -7.74
IIP-6b 84-91 9015B IIP-6b 5.39 9.65 -9.23
IIS- 9013 IIS- -59.19 -9.72 5.91
IIS- zi 9013 IIS- 5.40 9.82 -8.52
IIS- 95 9013 IIS- 5.42 9.87 -0.63
IIP-7a 96-103 9014A IIP-7a 5.47 9.79 0.00
IIP-7b 104-111 9014B IIP-7b 5.47 9.82 -1.50
IIS-10.2 112 9014B IIS-10.2 5.42 9.93 4.14
IIP-8a 113-120 9012A IIP-8a 5.43 9.97 -7.20
HP-8b 114-128 9012B IIPSb 5.44 9.95 -8.69
IIP-8c 129-136 9012c IIP-8c 5.47 9.91 -10.17
IIS- 137 9012c IIS- 5.50 9.95 11.49
IIP-9 138-145 9010 IIP-9 5.50 10.00 -4.20
IIP-1Oa 146-153 9011A IIP-1Oa 5.49 9.98 6.82
IIP-lob 154-161 9011B IIP-lob 5.50 10.01 5.33
IIS- 162 9002 IIS- 73.09 9.00 25.60
IIP-lla 163-170 9003A IIP-lla 5.55 10.00 -7.44
III’-llb 171-178 9003B IIP-llb 5.57 10.02 -8.92
IIP-12a 179-186 9002A IIP-12a 5.55 10.08 2.66
IIP-12b 187-194 9002B HP-12b 5.57 10.11 1.17
IIS- 195 9002B IIS- 5.52 10.23 6.16
IIS- 196 9002B IIS- -178.00 0.00 0.00
IIP-13a 197-204 9001A IIP-13a 5.62 10.16 1.62
IIP-13b 205-212 9001B HP-13b 5.60 10.20 0.12
IIS- 213 9001B IIS- 12.60 29.70 60.10
IIS- 214 9001B IIS- 5.52 10.30 7.67
IIS- 215 9001B IIS- 63.40 15.20 25.00
58
2.4.2 ACCURACY OF CALCULATIONS frame times were further manually rounded off
to the nearest tenth, introducing an additional
The accuracy of data presented in the photo 0.05 second of error, and yielding an RSS total
supporting data tabulation was estimated by of 0.119 second of error. Distribution of the
performing a simplified error analysis using error tends to be uniform; therefore one standard
typical photo and orbital parameters, and the deviation - that number which encompasses
best estimates of errors in the flight hardware. 68% of the possible cases - becomes 0.68 X
The study scope was confined to an investiga- 0.119 or 0.081 second. A typical value for hori-
tion of uncertainties in photo location and zontal velocity ,at the time of photography is
spacecraft altitude for the prime photo sites. 1.917 kilometer’s per second; hence, the dis-
A brief summary ‘of the estimated la errors is tance traveled downrange is:
given below in Table 2.4-3. 1.917’kmls x 0.081= 0.155
59
Table 2.4-4: Nominal Assumed Attitude Errors - Initial Conditions
tracker null to
reference prism
IRU alignment to
reff+ence prism
RSS subtotal
3 0 Error (degrees)
60
A value of 0.24 can be used as the 1 Q error for the effects must be studied separately.
each axis within the accuracy of the analysis.
Since these errors are assumed normal and inde- Telephoto
pendent, the same value applies to errors des-
cribed in camera roll, pitch, and crab coor- The telephoto field of view is 20.36 degrees in
dinates, or the crossrange direction and 5.17 degrees in the
downrange direction. An orbit inclination of 12
u r = 0.24 degree degrees and spacecraft altitude of 50 km are
up = 0.24 degree assumed. The longitude and latitude compo-
u c’ = 0.24 degree nents in the crossrange direction were deter-
mined,
The Q r error results in a cross-frame position-
ing error and the up results in an along-frame A Ac = 0.0012 degree
positioning error. These cross- and along-frame A LCc = 0.0058 degree
errors are rotated through the 12-degree inclina-
tion angle into latitude-longitude errors. Since Uncertainty due to the 5.17-degree field of view
again the roll and pitch errors are normal and downrange is similarly calculated:
independent, the error in the latitude and longi-
tude directions are also 0.24 degree. A A d = 0.00147 degree
A P d = 0.0031 degree
Up = 0.24 camera degree at 55 km alt = 0.0076
degree latitude Having found the downrange and crossrange
ux = 0.24 camera degree at 55 km alt = 0.0076 components of uncertainty, it is necessary to
degree longitude sum these to complete the estimate of un-
certainty in photo corner location due to site
Uncertainty in State Vectors elevation,
Accuracy of the state vectors must be considered AA=(AA ~"+AA d2)*'2=0.0019degree
with the uncertainties in actual photo location. (high-resolution longitude)
Typical uncertainties for a state vector at a photo
2 112
site are: Ak‘=(Ad +Ard) = 0.0058 degree
(high-resolution latitude)
ux= 76m g x = 0.14 m/s
uy=‘130m Q y = 0.33 m/s Wide Angle
“z=275m u z = 0.50 m/s
The wide-angle-lens field of view is 44.24 de-
Assuming a spacecraft altitude of 50 km, these grees crossrange by 37.92 degrees downrange.
errors transform to the following: Proceeding in identically the same manner,
0~ = 0.0042 degree AAc = 0.0027 degree
U
p = 0.0088 degree APc = 0.0131 degree
Q,h = 0.16 km A CLd = 0.0112 degree
A xd = 0.0023 degree
2.4.2.2 Uncertainty In Site Elevation Summing the downrange and crossrange com-
ponents,
The elevation of prime photo sites above or AA= 0.0133 degree
below the mean radius of the Moon is known AP = 0.0115 degree
(1 u basis) only to within about 1 km. Since the
camera axis intersect is only very slightly dif-
ferent from the nadir (prime sites only), site- 2.4.2.3 SUMMATION OF ERRORS
elevation uncertainty has no noticeable effect
on location of the photo centers. However, loca- Sources that are known to contribute uncertainty
tion of the photo corners is directly dependent to photo locations and altitude and that have
on site elevation and this relationship is in- been investigated here are considered inde-
vestigated. Also, because the telephoto and pendent, and are lumhed together by the root-
wide-angle lenses have different fields of view, sum-square method (See Table 2.4-6).
61
Table 2.4-6: Summation of Errors
PHOTO CENTERS
8.
Source UA U.P UY
PHOTO CORNERS
Telephoto
Source UX
Source OA UP
For the photo corner locations, effects due to 2.4.3 PHOTOGRAPH LOCATION FRAME
uncertainty
_ in site elevation must be added to COORDINATION
the below figures for uncertainty in photo center
location. This is done for both the telephoto and Preliminary attempts were made to correlate the
wide-angle cases below. lunar topographic features in the Mission II
photographs with existing 1:500,000 and
1: l,OOO,OOO scale lunar Mercator projection
It is repeated that the frames evaluated by use charts. It was immediately apparent that such
of in-flight orbit determination are not as accu- a correlation could only be approximate. In
rate as those for which postflight OD was done some cases, features larger than several kilo-
using improved data. Where conflict with actual meters could be identified on both charts and
photos is observed to exist, the EVAL data must photographs. However, discrepancies amount-
be adjusted to obtain meaningful values. For ing to several kilometers were frequently found
instance, an error in longitude of frame locations between relative positions of these features. In
requires approximately a one-to-one correction other cases, features over 2 or 3 kilometers, seen
to the incidence angle printed ( + if away from in the photographs, could not be identified on
Sun, - if toward Sun). the charts. The limitations that have been im-
62
posed by Earth-based observation in preparing craft film in conjunction with pre-exposure
current lunar charts in some instances make of the edge data. These marks are de-
their use for precisely locating the position of scribed in Figure 2.3-l.
Lunar Orbiter photographs difficult. In plotting l The optical-mechanical scanner may also
locations of photograph corners on the charts by introduce a small error in the film-advance
the above method, deviations of as much as an direction.
order of magnitude greater than the errors l Slight errors in both the longitudinal and
shown in Paragraph 2.4.2.3 from the computed transverse direction with respect to the
positions were noted. This effort confirmed that spacecraft film may be introduced by the
an extensive study will be required to transfer reassembly process.
the topographic information from the unrecti-
fied, nonorthographic projection photographs Although the primary objective of the Lunar
to lunar chart form. Furthermore, the currently Orbiter mission was to secure topographic data
available “actual” postmission EVAL data for regarding the lunar surface, there was no s’pe-
frame coordinates have limited value in this cific plan in the original concept to produce
application because of the assumptions made in accurate maps of specified topographic detail.
the EVAL computer program. In this program A comprehensive error analysis, as discussed
the Moon was assumed to be a sphere, with a above and necessary for such photograph utiliza-
mean radius of 1738.09 km. Consequently, ele- tion, Was not made and has not been incorpo-
vation differences over a given site were not rated into the photodata reduction.
considered. Also, spacecraft dynamics were
simplified and did not include pitch and yaw 2.4.3.1 Photographic Image Distortion
errors in the postmission EVAL computation
of frame corner coordinates. Further complica- The final photo image in the spacecraft camera
tions were introduced by uncertainties in tim- is distorted by an aggregate of internal camera
ing, as well as by the different fields of view of phenomena. These can be conveniently lumped
the telephoto and wide-angle cameras. To estab- into two areas: (1) uncalibrated lens distortion;
lish corner coordinates, and to properly cor- and (2) thermal-chemical emulsion distortions.
relate them to existing lunar charts, a full photo-
grammetric space resection should be per- Lens Distortions
formed. Each usable frame must be analyzed
with respect to spacecraft position, altitude, The Lunar Orbiter II mission was predominate-
velocity, and attitude prevailing at the moment ly reconnaissance rather than cartographic. The
a given target area was photographed. In turn, 80-mm Xenotar lens used was chosen for its
these factors must be related to camera geometry excellent resolution rather than metric fidelity.
and the lunar surface. Further uncertainties in A typical 80-mm-focal-length Xenotar can have
positional accuracy are inherent in the Lunar as much as 340 or. maximum distortion and
Orbiter photographic system. still qualify as a suitable reconnaissance lens.
This can be contracted with a selected, 76-mm
l The Schneider Xenotar lens used for the focal-length mapping Biogon that has a maxi-
wide-angle photographs is not a photo- mum distortion of 30 p radially and 10 ~1 tan-
grammetric lens and as such introduces gentially.
some distortion. This lens was calibrated
prior to flight to reduce the effect of dis- Thermal-Chemical Emulsion Changes
tortion error in final analysis.
l Processing of the film aboard the space- The Lunar Orbiter II mission used Type SO-243
craft and the subsequent reconstructed film for the photography because of its high-
record introduces distortion of the film resolution characteristics. Since SO-243 uses a
image. These distortions are sensitive to triacetate base, it does not have the extreme
temperature and relative humidity of each dimensional stability characteristic of estar
film or copy generation. (mylar) base films used for cartographic photog-
l A random error in the mechanical scan raphy.
direction of the optical-mechanical scan-
ner introduces one of the major errors in Photographic film changes under the following
the spacecraft camera system. To permit primary influences:
at least partial correction of this distor- 1) Changes of temperature and humidity;
tion, reseau marks in the form of small 2) Aging, long term and short term;
crosses were pre-exposed on the space- 3) Processing.
63
Second-order parameters influencing dimension EVAL tabulation is identified as “slant dis-
changes do not contribute significantly. The tance” in the supporting-data table. Figure
unpredicted image distortion expected in Lunar 2.4-3 is a diagram of the geometry of these
Orbiter II photography from the cited internal parameters.
camera influences is summarized in Table 2.4-7.
It is emphasized that this table is by no means Information required to support the photo
exhaustive, and is presented to show orders of analysis function was coordinated with NASA
magnitude of the problem rather than to deter- and the user agencies during the program design
mine a cartographic error budget for the film. period. These requirements were implemented
Although the photographic image is subject to in the form of the double-page tables of sup-
the above distortions and to additional distor- porting data, Table 2.4-8.
tions during readout, reconstruction, and re-
assembly, the reseau pattern provides a means All of the spacecraft position and attitude data
of correction for all but the lens distortions. is listed on the left-hand page. The data tabula-
Correction for the latter in the wide-angle photo- tions on the right-hand page are grouped to
graphs is provided by the lens calibration. support the high- and moderate-resolution
photographs. The predicted corner positions
are based on normal operation of each camera.
2.4.4 PHOTOGRAPHIC SUPPORTING DATA Each line in the table presents all of the sup-
TABLES porting data for that dual exposure.
The information presented in the supporting The supporting data in Table 2.4-8 has been
data tables has been extracted from the com- arranged by order of exposure for each primary
puter program EVAL tabulated output. Figure site. This is then followed by the secondary-
2.4-2 is a sample of EVAL program tabulations. site photographs arranged by order of exposure.
The EVAL program was developed to satisfy
the operational requirement of predicting photo The convention for presenting the coordinates
coverage and determining spacecraft maneuvers of the four corners is illustrated in Figure 2.4-4.
required to obtain the desired coverage for
each photo sequence. It should be pointed out that the solution for
the photograph corners by the EVAL program
The following is a definition of terms used in breaks down where the lunar horizon is in-
the EVAL program and, with one exception, cluded in the field of view. For this reason,
are the same terms and definitions used in the corner coordinates for the oblique photographs
SuDDortina-data tables. The sinale difference is of Sites IIS-7. -12. -15. and -17 are not included
that& the t&-m “camera axis mainitude” in the in the tabulation.
% DIMENSION PER
% RELATIVE HUMIDITY 0.008 - 0.010 0.009 10% RH 0.09
% DIMENSION PER
DEGREE FAHRENHEIT 0.003 - 0.004 0.004 10°F 0.04
PROCESSING DIMENSION
CHANGE 0.08 - 0.10 0.09 -__
0.09
FILM AGING PAST
PROCESSING 0.15 - 0.25 0.15 --_ 0.15
RSS = 0.20%
1 A
64
l **.*C.*.C**.***CC*****.*.*****~***
LCNCITUOE OF kACIR FEINT = 36.8437486 OEt LATITUDE OF NADIR PC1 NT = 3.2883279 DEG
LC.hG CF CAMERA AXIS I”ITEKSECT = 36.6312671 DEG LATI OF CAPERA AXIS INTERSECT = 3.5237039 DEG
SPACECHAFT RADIUS = 1783.6529083 KM SPACECHAFT ALTITUDE = 45.5629120 KM
HEAh ALrITUOE RATE = -0.0685107 KM/SEC TIME FROM PEKIAPSIS 5 -Lb.3998415 SEC
HCRILCNTAL VELCCITY = 1.916t221 KH/SEC TRUE ANOMALY = 356.9901314 DEG
SCALE FACTCR IHIGH) = 0.0133881 H/KM TILT DISTANCE (HIGH1 = 126.6060276 Hh
SCALE FACTCR ILOW) = 0.0017558 M/KM TILT GISTANCE ILCCII = lb.8663642 MU
IPAGE t’CTICh COCt’ENSATrON (V/HI= 0.0420698 R4Df SEC ShING ANGLE = 127.2153053 DEG
EPISSICh ANGLE - = 12.2221454 OEG- - INCIDENCE ANGLE = 70.2003831 DEG
PHASE AhSLE = t2.1474490 DEG NORTH DEVIATION ANGLE = 349.8523178 DtC
TILT ARGLE = 11.9052935 DEG KESOLUTION CONSTANT I l1.9887152 !lTH
TILT ALIPUTH = 317.9831886 OtG SUN ALIMUTH AT PRI NC1 PAL GNO t’T= 91.4987173 DtiG
SUN ANGL’ AT hAUIR = 70.062C518 DEG SUN ARC AT NADIR = 2125.3598938 KM
LCNGlrUCE CISTANCE TC TAKCET = 0.4267408 DEG LATITLOE DISTANCE TC TARLET = -3.3056721 DEG
LCN:;I?ULi AN LENGTH ro TARGET = 12.9455912 KM LATITUDE ARC LENGTH TO TARGET = -9.2726828 KM
FCRhARO CVERLAP RATIC = 14.8351394 PCT SIDE OVERLAP RATIO = 0. PCT
TIt’E tiETkith PHCTOS = 1.9OC2914 StC
x Y 2 MAGNITUDE (KP)
DIWECTICS CCSINES TC TARGET -0.60295258 -0.78584789 0.13744549 48.32780266
CAf’ERA AXIS -0.70600btC -C.7C154638 0.0968bbY9 46.59169006
Cl -0.73921973 -0.62203047 0.25813232 C8.12425232
Cd -0.71169133 -0.69723281 -o.otl58uLso 45.9911193tl
C3 -0.64919493 -0.75761244 -0.0675Y687 46.70896437
c4 -0.b7672332 -0.68241011 0.27633674 4R.Yl184998
14) (3) l
65
HORIZONTAL VELOCITY
MEAN ’
ALTITUDE RATE
SURFACE
NORMAL
- TILT ANGLE
SUN ANGLE AT
V GROUND POINT
Y rv
-TILT
Figure 2.4-3:
AZIMUTH
Photographic Geometry
DEFINITION OF TERMS
Camera Axis (Slant Distance): Direction cosines
and magnitude (selenographic of date) of camera
axis at time of photo.
Cl, C2, C3, C4: Direction cosines and magni-
tude (selenographic of date) of the vectors from
Figure 2.4-4: Corner Coordinate Designation spacecraft to photo corners.
Convention
Direction Cosines to Target: The direction
The Theoretical on-axis ground resolution of cosines and magnitude (selenographic of date)
the photographs is given by: of the vector from the spacecraft to the point
targets.
Telephoto: R= 5 Emission Angle: Angle between surface normal
and camera axis. Also, the angle between the
Wide angle: R= H photo image plane and the subject plane.
5.75
Forward Overlap Ratio: Ratio of amount of
Where R is the resolution in meters, and H is overlap to telephoto frame dimension along the
spacecraft altitude in kilometers. For oblique direction of the flight path.
photographs, R is approximate when H is the
slant distance from spacecraft to ground princi- Horizontal Velocity: That component of space-
pal point. craft velocity perpendicular to a radial line
66
through the spacecraft and in the direction of Spacecraft Radius: Distance from spacecraft to
the flight path. Moon center.
Image Motion Compensation (V/H): The IMC State Vector: Spacecraft position and velocity
rate is the instantaneous rate of movement of components in selenographic (of date) coordi-
the image across the focal plane and is a function nates at the time of photo.
of spacecraft velocity and its height above the
surface (V/H ratio), and the lens focal length. Sun Angle at Nadir: Angle between the space-
craft/nadir line and the Sun’s rays.
Incidence Angle: The angle between surface
normal and the Sun’s rays. Sun Arc at Nadir: Arc length from the nadir
point to the intersection on lunar surface of
Longitude (latitude) Arc Length to Target: Arc Moon center to Sun centerline.
distance measured on lunar surface between
the meridian (parallel) through the spacecraft Sun Azimuth at Principal Ground Point: Azi-
nadir and the meridian (parallel) through the muth of Sun’s rays at the camera axis intersec-
target. (+ is east longitude or north latitude). tion, measured clockwise from north.
Longitude (latitude) of Camera Axis Intersect: Surface Normal: A line normal to the Moon
The selenographic longitude (latitude) of the surface at the point of camera axis intersection.
point on Moon surface intersected by the camera
axis. (+ is east longitude or north latitude). Swing Angle: Angle between cross-axis of film
frame (the Y’ axis) and a line from center of the
Longitude (latitude) Distance to Target: Angular frame to the image of the nadir point. Measured
distance in longitude (latitude) between camera positive clockwise from the positive Y’ axis.
axis intersect and point target.
Longitude (latitude) of Nadir Point: The seleno- Tilt Angle: Angle between the camera axis
graphic longitude (latitude) of the point on the and the spacecraft/nadir line.
Moon’s surface directly below the spacecraft. Tilt Azimuth: Azimuth of principle ground point
from spacecraft nadir.
Mean Altitude Rate: Rate of change of altitude
with respect to time. Tilt Distance: Distance from the image of the
camera axis intersect to the image of the nadir
North Deviation Angle: Deviation of north
from the cross frame (cross) film axis (Y-axis) point measured on the spacecraft film. Given
measured clockwise. for both high- and low-resolution frames.
Phase Angle: The angle between the camera Time between Photos: Predicted time between
axis and the Sun’s rays. exposure of current frame and succeeding frame
taken in a film sequence based on the V/H at
Principal Ground Point: Intersection of camera the time of current frame.
axis with the lunar surface.
Resolution Constant: The theoretical ground Time from Pariapsis: Time in seconds before
resolution of the high-resolution photographs. (minus) or after (plus) periapsis passage.
Moderate-resolution is larger by a factor of 8. True Anomaly: The angle in the orbital plane
The constant is equal to actual altitude in km, measured from pariapsis to the spacecraft in
divided by 46 (the nominal altitude giving the direction of motion.
l-meter resolution on the high-resolution photo-
graphs). Direction of Motion: The arrow that appears on
Scale Factor: The proportionality constant to the printout illustrates the general direction of
relate dimensions on the spacecraft film to spacecraft motion for determination of the photo
dimensions on the lunar surface. Given for footprint orientation.
both 80- and 610-mm camera systems.
Photo Footprint: Numbered asterisks that appear
Side Overlap Ratio: Ratio of amount of overlap on the printout which represent the four corners
to frame dimension perpendicular to flight of the photo frames as projected on the lunar
path (e.g. on adjacent orbits). surfaces. Adjacent to each of the asterisks are
the longitude and latitude of that corner of the
Spacecraft Altitude: Altitude of spacecraft footprint; between the asterisks is the surface
above Moon surface. distance in kilometers between those corners.
67
Table 2.4-8: Photo Supporting Data
2%
1
i ;? 1.31.6 1.t
1.:
-0:a
I
) 1 1.10.7
3:;
.
;;g
. 2:
-0.0% )13 73.0 73.4' 0.
15:25rl2.c
15:25r14.1
pqrl6.r
-0.03
-0.03
-0.03f
1
;
JL0.J
0.1
73.0
73.0
73.0
73.3
73.a
73.u
0. 1
0.2
0.1
15C25a8.! -0.03 I 37.53
37.6
LL0.1
0.0 0.c
15r25:P.4
15l25:22.5
15r25s4.C
-0.034
-0.032I
-0.03l
37.76
37.&
LL::t 73.0 72.5!
0.1
%
0.0x? 2.7e
0.013I 2.76 z-6
10.20.1
0.2
ck49r47.1
0.014 2.73 33:m
0.015 2.71 33.93
II 0.1
0.2
:::
0.2
o.ol6
I, ::t0.5 0.3
0.4
z% I
0:019, , 0.7 67.0 67.1~ ::z
15:44:22.3 2Qo.m
15:44:24.4 21.01 3 ::I
22.15
21.2-7 , 1.5
1.3
1.4
1.3
15r44r30.8 .O.c%l 2l.40 1.2 1.2
15db33.0 .0.0&J 1.1 1.0
15:44:35.1 -0.059I xzi
15144137.2 .O.Cfd 2l:Tg 3 Z
;;;;;:z.; .0.051
.o.qo
20.69 1.3 1.3
I 20.81 1.2
19:13t28:fJ .o.c49 I m.94 i:f 1.1
19r13r30.8 -0.040 I 21.06 1.0 0.9
19:13:32.9 :CpJ I 2l.19 ,/0.0 0.8
19:13:35.0
19:13:37.0
19r13r39.1
.0’04
-0:d
I
I
I
::4;
.
/,p:;. i:t
.
2!2Ao~59.4 -0.082 I 15.20 1.8
zz2r41rol.6 .O.C81 I 15.33 1.7 2
22:41:03.8 .0.030 I 15.46 1.5
e2:411c5.9 0.079 I 15.59 ::2 1.3
I4.78
~:Kt, .O.O@
.O.OTT I4.76 :::
22r41fl2:3
22r41r14.5
.0.075
-0.45
I4.73
I4.71 fki.
MY 3x?
021l2135.-f 0.012 24.32
o2rKr37.8 0.01 24.45 ;:;
02:12139.7 0.01 t 2.71 24.56
02:12:41.7 0.015 2.69 24.69 ;:;
ax2143.7 0.016 2.66 24.81 69.1 67.95
02:l2:45.7 0.017 24.93 ;:;
oz2m47.7 0.018
02:12:49.6 0.019 1.59 g:Zi
I -
68
I -
ONG
TILT
DlSl
SCALE
:AcloI
k A
PHOTO CORNER
R ~~~
OORDINATE
C D
qziz f5 IAT LONG IAT 1 LONG MT LONG
)EGDEG IEG DEG MM 3 IEG DEG DEG DEG
-11
2% 2%
I I
0.3
1.5
0.013
0.0~
4.21 37.63
4.18 37.76 L:
3-g:;
. 0.04
0.2
O.OD2
0.002
2.0 o.ol3 4.16 37.89 14
4.2 0.013 4.13 9.02 '4 $2 2. 0.002
0.002
~2.6 0.013 4.71 21.49 4 .73 a.35 1.6 0.002 .72 21.77
u.1 0.013 4.68 21.63 i4 a.49 0.002
9.8 0.013 4.65 21.76 :Z Zl.62 i:; 0.002 :z cx
8.4 0.013 4.63 21.69 .:: .65 2l.n 1.1 0.002 .65 22117
a.15 1.1
::: 0.013
0.013
4.35
4.32
21.29
21.42 sf:
.38
14 :g
21.20
3.41 I:f
0.002
0.002
.40 a.55
Z:f 0.013
0.013
4.9
4.27
21.54
2.~67 ,4 .30 il.54 .
0.002
0.032
: t5.80
t5.6-r
:::
1.3
0.002
0.002
O.W2
5.55
i-52
i.49
15.26
15.39
15.52
: ix . 1.1 0.002 .gr 16.50 5.46 15.66
z4.33 0.002
t4.46 ;:1' 0.002
t4.57 0.002
!4.70 ::: 0.002
69
Table 2.4-8: Photo Supporting Data (Continued)
- _...- --
7
tUlNClPAL
PHOTO TIMEOF EXPOSURE SPACECRAFT GROUND NOR1
s IANT SUN EMS
--. POINT
SION
PHASE ‘NC1 TILT TILT
iW’NG
-r DEVll
DISI UIM NGL ,NGLE z; ,NGL UIM
ItMr- L4T I.ONG
-.-
jKO,.,DS 1 HR:MIN:SEC c DEG DEG KM DEG DEG DEG DEG DEG DEG
i
STIMATED ERROR f .(Q -iFI
L .m 1.1 .Ol r2
L 75
A L 01
II
1 :1.X ) :23.6t i I 47 91.a: 0.6 0.6 93.5s
1.11 r :23.75 1 0.7 0.6 97.56
/ i 1.1: i : , 1 0.8 0.8
I i 1.1: , :2:& I , 1.0 0.9 g::
I rnY p4
‘-7s
% CP2:52:34.8
C
’
r
: 2.5:
I
I .-2.lC 1
1
,
,
0.1
0.1
'0.2 70.2
'0.2 70.1
0.1
0.1
56.7c
z99 C
C
I
I
z.51 . .
: z.45 1 .:;'H
i 2.4t i .-1:n
I I
41 91.2t
0.2
0.3 1E.E
. $.f.
0.2
0.3
57.05
7g
- . ..-. --- -L
70
Table 2.4-8: Photo Supporting Data (Continued)
>Isl
w
A
DNG
I
ONG
DISI :KTo(I .ONG
iii -3
KIO DEG IEG DEG MM x10-’ DEG
2%
- 2% -
2% 2%
6.1
7.,
0.,
LO.’
LOI. 1.45
I.013 1.43
a.013 1.43
LOl.3 1.38
3.013 1.35
3.013
LO13 big
a.013 1.27
23.80
2.2
24119
0.
0.
0.
0.
0.
0.
0.
0. 24.48 1.25
:;g
z-5;
0.8
1.0
23:93 1.1
24.g 1.3
:::
24146 1.9
24.59 2.1
O.UX!
O.ooO
0.W2
0.002 1.63 24.72 0.
0.002
0.002 ::5e
60 a.00
24.86 0.
0.002 1.55 25.13 0.
O.WQ 1.52 25.27 0.
24.07
24.20
24.33
24.46
24.74
0.70
0.67
0.64
0.61
24.60 0.56
0.55
24.87 0.52
25.01 0.49
Z’~ 1.9
l-i
1.&J
i3:29 1.87
23.55 1.82
;;-:f
1.79
1.76
23:95 1.74
23.29
23.42
23.55
23.41 0.84 23.67
23.81
23.95
24.07
24.21
7.' Cl.013 1.08 0. 23.42 l.U 23.54 1.0 O.W2 22.83 1.56 23.15
9.* 3.013 1.05 0. 1.2 O.oop 23.01
LO.1 LOX? 0. ~~-~ 1.4 23.4
Ii?.: LOI2 ;:g 0. 23195 1.6 ::Ei 24.37 0.20 23.B
Lg.’ I.012 O.% 0. 23.97 0.95 24.O9 1.8 0.002 1.23 24.79 -0. 24.52 0.16 a3.42 1.45 23.69
L5. 3.012 o.* 0. 24.10 0.5 24.23 2.0 1.21 24.93 -0. 24.65 0.13 23.55
16.’ 3.012 :.g 0. 24.37 2.2 EZ 1.18 a.08 -0. 24.80 0.10 23.69
Le.. I.012 0. 24.51 2.4 0.002 1.15 25.22 -0. 24.94 0.W 23.83
4.1 I.015 E.2 1.55 2.n -1.76 2.65 -1.67 0.6 0.002 -2.22
5.' Loo5 1.43 2.19 -1.65 2.61 -1.55 0.8 O.W2 -2.ll z*: :f%
6.' LO15 2:62 1.32 2.17 -1.54 2.6: -1.44 0.9 O.OCQ -2.00 3:03 -1:78
8.1 I.015 2.60 1.20 2.14 -1.42 2.6: -1.32 1.1 0.002 -1.88 3.00 -1.66
1.' I.015 2.40 2.17 1.94 -2.39 2.k -2.29 0.2 0.002 -2.85 2.01 -2.63
2.1 LO15 2.9 2.6 .i.ge -2.28 2.4~ -2.18 O.OCQ -2.74
3.1 1.015 2.35 -2.07 I:; O.W2 -2.63
4., I.015 2.33 t:g -1.9 O.oop -2.52 2.741 -2.291
5.' I.015 2.21 1.72 -1.84 0.8 0.002 2.53 a.25 1. -1.47 1.63 -2.40
7. 9.015 2.20 1.60 -1.72 0.9 0.W2 -2.29
8. LO15 2.26 1.49 -1.61 1.1 0.002 E: 1; -1.02
-1.13 1. 1;.g ;*z -2.18
9.1 LO15 2.24 1.37 -1.49 1.2 0.002 2.46 -0.90 1. -ii3 1156 -2.6
8.1 I.013 0.99 1.18 -1.31 0.002 1.24 -0.65 0. -0.91 0.23 -1.95 1.45 -1.69
9.' 1.013 O.% 1.05 0.002 1.21 -0.52 -0. -0.78 0.20 -1.82 1.42 -1.56
u.: I.013 0.93 0.9 :1'2 0.002 1.19 -0.3 -0. -0.66 0.17 -1.70 1.40 -1.44
l2.1 LO13 0.91 0.79 0.39 -1.05 0.9 -0:93 0.002 1.16 -0.26 -0. -0.52 0.14 -1.57 1.37 -1.31
L4.1 I.013 0.80 0.66 -0. & 1.9 0.002 1.14 -0.13 -0. -0.39 0.11 -1.44 -1.18
I.013 0.53 -0.67 2.0 0.W a.31 2:: -1.05
:2*; I.013 ::gl 0.40 -0.54 O.W2 ::g 0.14 -0.
0.00 -0.26 0.09
-0.13 0.06 1.30 -0.93
t8:. I.013 0.8D 0.27 -0.41 2 0.002 1.06 0.27 -0. 0.00 0.03 2%. 1.27 -0.80
LO.. LOI.2 0.62 1.33 0.08 -1.59 0.6: -1.47 0.002 -2. lj l.l3 -1.86
tl.1 I.012 0.59 1.19 0.05 -1.45 0.6: -1.33 t:; 0.002 -2.00 1.09 -1.73
L3.1 L OIZ 0.02 -1.32 0.55 -1.20 1.7 0.002 1.05 -1.60
L4.1 LOX? t::. 2: 0.01 -1.18 0.51 -1.06 l-9 O.W2 :$ 1.03 -1.46
L5.I LOl2 0.51 0.78 ‘0.04 -1.g 0.51 -0.93 2.0 0.002 -1.60
17. LO12 0.48 0.65 Q.4 -0.92 0. LI -0.79 0.002 a.47 i:g -1.20
-1.33
18.1 L ol2 0.45 0.51 0.10 -0.78 o. -0.66 ::: O-W2 -1.34 0.95 -1.06
xl.1 LOI2 0.43 0.37 0.13 -0.64 0.w -0.52 2.7 0.002 -1.20 0.92 -0.92
--. L _-.-
71
I.
I I .I,., 111mmm.111m.m I , , ,.,.,, , . I I a.. ,a . , am.-- ..-.... _. . ..--. . . - _.-._-..--. -._. ._. _ _ ..-
AY 314 dtinu 0
0.105 348.:
0.106 348.1
0.107
0.108 ;z-; .
ff 35
lO:ll:15.1 44 0.053 1.x) -13.: 11.20-13.33 66.: 348.1
1o:ll:17.1 45 0.054 1.18 -13.: , 1.18-13.21 66.2 13 348.1
lO:ll:19.1 45 0.055 1.15 -13.1 1.15~13.e 66.: N&
lO:ll:22.1 45 0.056 1.13 -12.5 1.13-12.N 66.1 :I .
14: 1o:u:23.0 45 0.057 1.10 -12.E17 1.10-12.84 0 348.1
14: lO:U:25.1 45 0.058 1.08 -12.1'4 1.07-12.71 14 348.1
1o:u:27.1 45 1.05 -1e.t >2 1.05-12.59 ,7 348.1
i$ 1o:ll:2g.1 45 XE
. 1.03 -12.: i0 1.02-12.46 0 348.1
L3:36:25.1 45 0.053 ;3 3.71-27. 5 82.18
2 13:36:27.1 45 0.052 ;.xg
. :g.$. !Q 3.69-n. z 3 ;z:; !82; 29
13:36:29.1 45 0.051 3.66 -27.2 ,* 3.66-27.31 76.: r82.44
:$ 13:36:3l.o 44 0.050 3.63 -z'l.l .7 3.64-27.19 76.5 !82.62
1% p45& 3.61 -q.c 15 3.61-27.06 !82.87
151 ;.;; :z.; 83.23
15: p&7 I: !83.79
15: . 3:59 -266:t
19 f84.73
154 0.037 2 3.32.27.54 $3.22
15: ;.3$
. :;.: . .l 3.29.27.42 183.51
15t %2 3.27 -27.2 9 3.27.27.X 183.92
151 0:035 3.24 -27.1 3.25-27.19 !t34.52
15E 17:05: 37.6 43 0.033 3.22-27.06 75.5
t7:05:39.5 43 0.033 ;'= -2: : 200-26.95 75.:
z L7:05:41.5 43 0.03l 3:17 :26:0 2 ::17-26.82 75.5
161 17:05:43.4 43 0.030 3.15 -26.7 0 3.15-26.70 75.5
u 3-5
)7:03:50.2 51 0.039 0.x, -20.2 2 0.20~m.1g 62.5
:2 ,7:03:52.4 52 0.090 3.17 -20.0 0.17-20.05 62.5
165 17:03:54.7 52 0.092 590.14-19.91 62.9
166 )7:03:57.0 52 0.093 ;.g
. 1;:; . 1 o.ll-19.77 62.9
167 17:03:59.3 52 0.094 0.08.19.63 62.9 348.1
160 ,7:04:01.6 52 0.095 ;.ct&
. -.
4;; I 0.05.19.49 : 348.1
169 ;:p$.; ;; 3.0% I.03 -19.3 9 0.02.19.34 ~~~; 5:
L7O : : . 0.098 LW -19.2 6..O.Ol-19.20 62:9 6: ;e: .
L7l to:32:54.5 55 3.105 I.21 -20.2 5.-0.21~20.29 348.1
172 LO:32:56.0 55 3.106 1.24 -x).1 -0.24-20.06 2';
,0:32:59.4 55 J.107 ).2-r -19.9 2:-0.28-19.90 m:5
:;z Lo:33:01.8 55 >.1og I.30 -19.a:1. -0.31~19.76 61.5
175 to:33:04. LllO J.33 -19.6 6. -0.34-19.60 61.5 30.17
176 .o: 33:cd. 3.ll.l I.36 -19.51 61.5 xl.14
.0:33:09. 56 I.u.2 I.39 -19.3 ;: 51.5 X.29
:; .0:33:u. 57 I.114 j.42 -19.2: 2. 51.5 MO.53
- --
72
Table 2.4-S: Photo Supporting Data (Continued)
.~--.
TELEPHbTO - ‘IDE ANGLE
O CORNER OORDINATES PHC )TO CORNER C OORDINATE
TILT SCALE
I I T C 0
OIST :AcIOl
LONG Fpi-z LAT LONG
*
OEG >EG 1 OEG MM ii- OEG OEG
2% I ~~ -I-I_ 2% 2%
29
.3o
tl.0
L2.5
14.0
:-z:
. :3.
0.012 0.21
-1.54
-1.40
-1.26
0.3
0.
0.30
-1.68 0.27
Ii.2 E.2
-1.70
-1.55
-1.41
1.4
1.6
1.8
o.M12 0.55 1i.g
0.002 0.52
0.002 o -0'67
:g 15.5 0.012 0.1eI -1.12 0.3 . . -1.27 2.0 0.002 :::7 -0:52
0.31 -1.82/T
0.012 0.161 -1.01 0. -1.29 0.19 -1.16 2.2 0.002 0.45 -0.41 .0.69 -1.88 0.68 -1.59
:x 0.011 0.13I -0.83 0. -1.l.l 0.16 -0.95 2.4 0.002 0.41 -0.22 a.73 -1.70
a:2 o.oll O.lC1 -0.63 0. -0.p-s 0.13 -0.83 2.6 0.001 9 a77 -1.55
a.7 0.011 0.07 -0.53 0. -0.82 0.10 -0.69 2.9 0.001 :::6 -kg .0.80 -1.41
.3a ;.~a; ;.;5 i -13.21 0. -13.45 1.47 -13.34 0.7 o.M)2 1.69~12.71 0.72-13.94 1.89-13.70
2:; ! -13.09 0. -13.32 1.45 -13.22 0.9 0.002 0.70-13.82 1.86-13.58
I,' 6.1 0:014 1:4: ) -12.96 0. -13.20 1.42 -13.09 1.1 0.002 0.67-13.70 1.84-13.46
.41 9.4 0.014 1.37’ -12.84 0. -13.08 1.40 -12.97 1.2 0.002 0.64-13.58 1.82-13.33
1.42 to.6 i -12.72 0. -12.96 1.37 -12.85 1.4 0.002 1.59-12.21 0.62~3.46 1.79-13.22
1.43 L2.1 pm; ;.;5
. 2! -12.59 0. -12.83 1.35 -12.72 1.6 o.co2 1.57-12.08
1.44 L3.3 0:014 1.3c, -12.46 0. -12.71 1.32 -12.60 0.002
1.45 t4.6 0.013 1.27’ -12.34 0. -12.59 1.30 -12.48 ::; 0.002 0.54t1j.09
1.46 L2.4 -27.44 3.4 1.6 0.002 4.20-26.94
1.47 L1.l 0,-g:: ;$ ; :-27.31 3.4 1.5 0.002 4.17-26.02
1.48 01014 3:gi -27.19 3.4 1.3 0.002
1.49 2; 0.014 3.ef I -27.07 3.3 1.1 0.002 4.33-27.57
1.5o 7.2 0.014 3.e.e; -26 95 3.3 -27.18 3.88 -27.08 0.9 0.002 4.10-26.45 3.13-27.68 4.30-27.44
1.51 ;.;a; ;.g I -26.82 3.3 -27.06 3.86 -26.95 0.8 0.002 3.lo-27a55 4.27-27.32
1.52 26' -26.70 3.3 -26.93 3.63 -26.83 0.6 0.002 4.25-27.19
1.53 3.3 01014 317eI -26.50 3.3 -26.81 3.81 -26.71 0.5 0.002 4.22-27.08
1.54 i -27.42 3.0 -27.65 3.58 -27.55 1.2 0.002 2.84-28.14 3.99-27.91
1.55 ;:Ej ;.;m; ;.;t. 3I -27.3 3.0 -Z+.54 3.56 -27.44 1.0 0.002 2.82-28.03
1.56 0:014 3.51 -27.19 3.0 4 -2-f.b2 I/3.54 -27.32 0.8 0.002 2.79 -27.91
1-57 5:3 0.014 3.45R -27.07 3.01 -27.30 3.51 -27.x, 0.7 0.002 3-72-26.59 2.77 -27.79
58 4.0 0.014 3.46; -26.95 2. g3 -27.10 3.49 -27.08 0.002 2.75 -27.66 3.89-27.43
2.8 0.014 3.44 -26.83 2. $6 -27.06 3.46 -26.56 ::2 0.002 2.72 -27.55 3.87-27.32
2,' 1.5 0.014 3.41 -26.71 2.94 -26.94 3.44 -26.84 0.2 0.002 2.70 -27.42
61 0.4 0.014 3.35 , -26.59 2.91 -26.82 3.41 -26.72 0.0 0.002 3.62-26.11 2.68 -27.39
163 L1.2 0.012 0.u I -20.05 0.12-20.17 0.09 -20.32 0.51 -20.20 1.5 0.002 0.76-19.47 .0.36 -20.9 0.99.20.61
164 t2.6 I -19. g1 0.12 -20.19 0.40 -x).06 1.7 0.002 .0.39 -20.76 O.Pd20.48
165 14.1 ;.y; ;.;5
. 2! -19.77 0.15 -20.05 0.45 -19.92 1.8 0.002 ,0.42 -20.62 0.93-20.34
166 t5.6 0.012 0.35, -19.63 0.10 -19.91 0.42 -19.70 2.0 0.002 0.45 -20.48 0.91-20.20
167 LT.1 0.012 0.36; -19.49 0.21 -19.77 0.40 -19.64 2.2 0.002 o.65-10.89 lg.lgI-0.48 -20.35 0.88-20.06
168 10.6 0.012 0.34 -19.34 0.24 -19.63 0.37 -19.50 2.4 0.002 0.62-18.75 19.04 -0.51 0.85-19.92
-20.21
169 !O.l 0.012 0.31 -19.20 0.27 -19.40 0.34 -19.35 2.6 0.002 0.59-10.60 18.89 -0.55 0.82-19.77
-20.06
170 a.6 0.012 0.2eI :-19.06 0.30 -19.34 0.31 -19.21 2.6 o.ccJ2 0.57-10.45 18.751-0.58 0.80-19.63
-19.92
171 L4.5 0.011 0.05, -20.06 0.51 -20.35 0.12 -20.22 1.9 0.001 0.30-19.44 1.0 0.63.20.66
172 15.9 0.ol.l o.oei -19.91 0.55 -20.21 0.09 -20.07 2.1 0.001 0.36-19.29 1.1 0.60-20.51
173 t-l.40.011 0.03I 0.58 -20.05 0.06 -19.92 2.3 0.001 0.33-19.13 1.1 0.57-20.36
174 19.0 0.011 -0.m , 1;;::: 0.61 -19.91 0.03 -19.77 2.5 0.001 0.30-18.98 L.l 0.54-20.22
175 a.7 0.ol.l .,0.04 a9.45 0.65 -19.75..0.00 -19.62 2.7 0.001 0.27 -18.82 0.51.20.06
176 Z2.4 0.ol.l ..0.07 -19.30 0.68 -1g.6o.o.03 -19.46 0.001 0.24-18.66 0.48-19.91
177 z4.1 0.ol.l ..O.lO, -19.14 0.71 -19.45..0.06 -1% 31 ;:,' 0.001 0.21-18.50 0.46-19.76
178 25.5 o.oll .,0.13 .-18.99 0.75 -lp.2g..o.o9 -19.16 3.3 0.001 0.18-18.34 0.43.19.61
73
Table 2.4-8: Photo Supporting Data (Continued)
r r
PHOTO
-
TIME OF EXPOSURE T 1.’
ANT
)IST
SUN
AZIM
TILT
NGLE
: S/C
r I
ECONOS 1 Hl:MIN:SEC DIG OEG OEG OEG
3.5
3.6
9:4:37.3
6:2g:25.0
3:24:10.8 1.1 k6 //cd4
Table 2.4-8: Photo Supporting Data (Continued)
T
TELEPHOTO WIDE ANGLE 1
I
)T -.__
0 CORNER ‘OORDINATES RNER COORDINATES
1lLT TILT
OIST l- C I 0 t OIST
/ I
1
c I
1
0
iiu
LONG
OEG OEG OEG OEG I LONG
OEG
LONG
OEG iOEG
UT LONG
1 OEG
L4T
1 OEG 1 OEG
LONG
2%
-i+
I
1
1.2 0.014 2.63 0.2 0.002 2.87-33.93 1.70 35.16 3.4 -34.91
2.3 0.014 2.62 0.3 0.W2 2.84-33.81 1.66 35.03 3.05 -34.79
0.014 2.58 0.5 0.002 2.02-33.69 1.65 34.92 3.02 -34.68
2:: 0.014 2.56 I.04 -34.17 ,34.19 0.6 0.002 2.79-33.57 1.63 34.79 3.00 -34.55
0.014 2.53 '33.95 !.02 -34.05 .34.07 0.8 0.002 2.77-33.45 1.60 .33.69 1.01 -34.67 2.97 -3h.43
i:; 0.014 2.51 ,33.82 .99 -33.93 ,33.95 1.0 0.W2 2.74-33.32 1.58 ,33.57 1.78 -34.55 2.p4 -34.31
0.014 2.48 ,33.7o .-VT -33.81 ,33.83 1.1 0.002 2.72.33.a 1.54 .33.44 1.76 -34.43 2.g2 -34.19
919 0.014 2.46 ,33.58 ..* -33.69 ,33.n 1.3 0.002 2.70-33.08 1.52 .33.32 1.73 -3k.p 2.89 -34.07
0.014 2.21 34.34 .69 -34.45 0.7 0.002 2.45-33.64 1.27 .a.09 1.48 -35.09 2.66 -34.04
2:: 0.014 2.19 34.22 0.8 0.002 2.43-33.72 1.24 .33.% 1.46 -3k% 2.63 -34.72
0.014 2.16 1.0 0.002 2.40-33.59 1.22 .33.84 1.43 -2k84 2.61 -34.59
X:", O.Ol4 2.14 1.2 0.002 2.38-33.47 1.19 ,33.72 1.41 -34.72 2.58 -34.47
10.2 0.014 2.ll 1.3 0.002 1.16 .33.59 1.38 33.59 2.56 -34.35
u.5 0.014 2.08 1.5 0.002 1.14 .33.47 1.35 34.47 2.53 -34.22
12.8 0.014 2.06 1.7 0.002 1.11 .33.35 1.33 34.35 2.50 -34.10
14.1 0.014 2.03 1.9 0.002 1.08 .33.22 1.30 34.22 2.4a -33.N
0.013 2.26 a73 -42.20 1.76-42.33 2.28 .42.2-i? 0.3 0.002 2.50141.58 1.31
5:: 0.013 2.23 1.73-42.20 2.26 0.5 0.w2 2.47'41.45 1.28
0.013 2.x) 1.7l-42.07 2.23 0.7 0.002 2.45-41.32 1.25
2:; 0.013 2.18 1. 6a-41.p 2.x) 0.8 0.002 2.42-41.19 1.n
0.013 2.15 ..62 -41.67 1.65-41.81 2.18 1.0 0.002 2.39-41.05 1.19 .41.30 1.41
2; 0.013 2.12 ..60 -41.56 1.63-41.69 2.15 1.2 0.002 2.37&.% 1.17 .41.19 1.38
10.2 0.013 2.10 1.60-41.57 2.13 1.3 0.002 2.35~40.81 1.14
u.6 0.013 2.07 1.57-41.44 2.10 1.5 0.002 2.32-40.68 1.u
0.013 1.84 ,42.04 ..30 -42.15 1.33-42.M 1.86 .42.17 0.8 0.002 2.09-41.51 0.8'7
::: 0.013 1.81 ,41.91 1.30-42.15 1.8b .k.O4 0.9 0.002 2.06-41.38 0.84
8.6 ;.z; ;.;x$ 1.27-42.02 1.81 Jb1.91 1.1 O.W2 2.04-41.25 0.81
9.9 . 1.25-41.~~ 1.79 .41.78 1.3 0.002 2.01-41.12 0.78 .41.38 1.00
u.3 0.013 1.73 ,41.52 al9 -41.63 1.22-41.76 1.76 .41.65 1.5 0.002 l.pe-40.99 0.75
t-s.6 0.013 1.70 ..16 -41.50 1.19-41.64 1.73 .41.52 1.7 0.W2 1.96~40.86 0.72
L4.0 0.013 1.68 ..14 -41.37 1.16-41.51 l.j"l .41.39 1.8 0.002 1.93-40.73 0.69
L5.4 0.013 1.65 ..l.L -41.24 1.14-41.38 1.68 .41.27 2.0 0.002 1.91~40.60 0.66
35.9 0.013 3.53 !.99 40.90 3.02 40.76 3.55 40.87 0.002 3.78 41.54 2.55 41.29 2.78 40.26 3.97 40.50
;.g; ;.5$ !.% 41.03 2.99 40.89 3.52 41.00 ::; 0.002 3.76 41.67 2.52 41.42 2.75 40.39 3.94 40.63
;7e:: !.$A 41.16 2.97 41.02 3.50 5.1 0.002 3.73 41.80 2.49 41.55 2.73 40.52 3.91 40.76
40.0 0:013 3:45 !.91 41.29 2.* 41.15 3.47 5.2 o.w-2 3.p 41.93 2.46 41.68 2.70 40.65 3.89 40.89
3.4 0.013 3.84 1.28 36.41 3.32 36.27 3.87 .7.0 0.002 4.10 37.07 2.73
30.7 0.013 3.81 3.29 36.41 3.84 .7.1 0.w2 4.07 37.21 2.7l
31.9 ;.z;; ;.;g 3.26 36.55 3.81 .7.3 0.w2 4.05 37.35 2.68
33.2 . . 3.23 36.69 3.79 .7.5 0.002 4.02 3.49 2.65
29.7 0.013 3.81 ~.rl 36.53 3.29 36.39 3.85 36.50 .7.0 0.002 4.05 37.16 2.89 36.87 3.04 35.86 4.38 36.06
28.6 0.013 3.78 I.24 36.64 3.27 36.51 3.82 36.62 0.002 4.02 37.28 2.86 36.99 3.O2 35.97 4.36 36.18
0.013 3.76 I.22 36.n 3.25 36.63 3.80 2.79 0.w2 4.00 37.40 2.a 3’7.l.l 2.99 36.10 4.33 36.30
2':. 0.013 3.73 I.19 36.09 3.22 36.76 3.Tl .6:6 0.002 3.97 37.52 2.81 37.h 2.97 36.22 4.3O 36.43
t38.e 0.014 4.55 ..Ol 4.43 4.40 .8.2 0.002 14.851 5.11 13.64 4.76 3.32 3.84 5.07 3.99
i0g.l 0.014 .*.c 0.002
7.: 0.013 1.02 12.33 0.47 12.21 12.19 1.c o.w2 1.28 12.87 0.01 12.61 0.24 11.55 1.49 LLQ
ll.: 0.015 2.85 -0.65 2.37 -0.71 -0.77 1.5 0.002 3.07 -0.20 1.99 -0.42 2.17 -1.34 3.26 -1.12
iii
75
Table 2.4-8: Photo Supporting Data (Continued)
- .-_... -_..-~ -
Pu INC IPAL -r
PHOTO TIME OF EXPOSURE SPACECRAFT a :ou ND 4ORl
EMIS
- -. r ‘olt ‘IT IsL4N SUN
ilOt.
‘HAS NCI TILT TILT WIN
IEVlr
7 DlSl ZlM NGl NGI
)ENC NGI AZIM !NG ‘IOh
: S/C GMT ALT < RT LAT LONG LAT ONG WGI
: P -- -. _. .-- ~~ - -
E
SECONDS HR:MIN:SEC xii .hL/SEC DEG DEG DiG DEG
FL DEG DEG DEG DEG DEG DEG OEC
-: -Et
STIMATED ERROR + .(IJ I.r .01 A!!& $J .MM I .01 .12 .1? fi .Ol .l( . 1c
ECC
- med
DAY 3l4
-11 lx 13:17:ll.f I 42 -0.03: L2.05 3.31 1 42 3.7 4.3 '4.9 0.; ?83.04 92.: 48.:
DAY 315
-1: 13-i 03:og:15.4 51 -0.10: 7.57 5.9 i3 51 2.0 1.5 33.4. l.! ?83.c4 92.1 49.1
DAX 316
-1: 166 00:05:42.7 46 0.051 1.06 10.05 i.6 147 I.92 i.1 0.0 i5.41 6g.t 0.03 77.! 57.'
DAY 37
-1: 1% OO:a?:55.7 48 -0.05: I.57 6x1 I.51s- 46.2 !8 48 1.l.l 3.0 5.3 '9.2: 2.: !82.06 4.8.:
-I! 14:16:og.2 48 .0.05( 1.57 53.84 1.1:L- 52.E81 151 1.0s 3.5 6.1 g.9: 6&t 11.75 2g.t
-1t 2l4 17:45:15x , 48 -0.044 3.16 53.71 1.b6- 53.6lo 48 1.1: 1.2 1.8 7.9 0.: 9l.29 48.4
-1 215 2l:12:53.5 51 .O.O6l 1.a ia. r.2:3- 58.271 u9 1.03 5.4 5.5 !Q.n 62.! l-l.79 34.;
FAR .
- P .
-3 33 i I .453 O.P! )A 3.93 .74.21 LO. 74.4 1!453 13.4 0.: 9.9 'O.Ot 0.1 61.50 5e.i ~76.
-4 34 I .450 0.32i 1-S3.95 -72.3 5.1 73.8II .576 57.9 Il.7 9.9 '1.11 16.t 5.97 16.4 169.
-5 75 1.4a 0.311i -!3.73 .50.4 Lo.' 58.2'1 ,533 r7.2 r3.4 ?.9 '0.7L te.4 .80.&S 32.2 1e1.
-11 1% 1,517 0.29: i -85.77 00.7 3.8 II ,517 12.6 0.t 3.9 '0.Y 0.4 90.17 96.1 177.
- - -- -. - - - - ---
76
Table 2.4-8: Photo Supporting Data (Continued)
AT
-.
.ONG
T
CCIORDINATE
ii- ONG ii
D
-
ONG
-i’‘IL1
IISl
SCALE
ACTOR
F
AT
- PHO ITC1 CORNER
ONG
I
ii ONG
s5l
-
ur
Gi
-
5iz IAT
- ONG
k
- -
:. WA
i
-I
I (IO D EG
- )EG E DE&
--
#EG DEG EG
- DEG IAM x10-3 IEG
-
)EG EG
- 1EG i&
- iii? c)EG
-
DEG
- 2%
-- 2% - - __ - - 2%
- 2% - - -
t2 7.2 0.014 1 3,A0 .2.00 1.1 .2.10 1.1 2.22 6: .2.12 1.9 0.002 I.8 11.53 .P 1.7: 2.69 4..0: 12.4i
17 0.5 0.01: ! 5,.18 4.49 -5 r1.61 1.6 7.76 2: 7.64 !.7 0.002 i.4 26.93 .12 ?7.1! .33 a.* 5i.7( 28.6
35 30.'9 0.013I 3..85 6.15 .2 46.2t ;.3 46.40 ff 6.29 4.1 3.002 .1 C5.62 036 .5& .05 $6.9 .* r6.6:
w 573 9 0.012 6.4 3.002
94 1.9 0.013I 3.,42 3.67 .8 53.7f !.9 53.92 4: i3.81 0.3 I.002 .6 53.14 -43 13.31 .64 63'.9(
54.111 54.x
35 193 3 0.012 6.5 3.002
33 2.4 O.OOll-1 8.1 .71.5 1.2 172.7 1.4 77.0 9. 16.1 0.3 D.ooO 1.' 49.26 15. 55.5 2.8 164.1 54. 63.0
34 s2.2 O.oo( 1 -11.0 70.21 3.' 173.2 8.' 78.9 4. 74.5 t3.9 O.ooO Ll. 53.8 l l l . Lb. L72.9
73 .5.4 O.OOt1 -: 17.1 913.2 0.1 0. .05.7 8. 13.0 2.0 O.COO 51. 75.0 7.1 30.5 .b.t .24.: 54.' 25.5
l :0RNHI OF UCx)N
__ - - - - - -
77
2.5 OPERATIONAL PERFORMANCE
Photographic operations pertinent to the eval- time, on the average. This bias was one-half
uation and use of Mission II photography are the expected frame interval time. Thus, the
discussed in this section. Detailed evaluation time programmed for a photo pass was the de-
of the photo subsystem operation during the sired time minus the half-frame bias.
mission is included as part of Mission II final It was not known by the cognizant personnel
report, Boeing Document DZ-100752-3, Volume during Mission II that this particular photo
III. sybsystem had an additional V/H sensor-deter-
mined delay between the programmed camera-
2.5.1 MISSION PLANNING on pulse, and the time code interrogation and
shutter operations. The actual exposure times,
Site locations, together with predicted orbital therefore, were late by approximately 0.3 +
parameters and photo subsystem operational 0.1 second. For V/H sensor-off photos, this
constraints, provided the basis for establish- delay becomes 0.9 second; these photos were
ing the film management and film budget plan late by that amount.
shown in Table 2.5-l. Because Mission II
followed the nominal plan closely, very few film 2.5.2.3 Exposure Control
budget changes were required. The nominal
plan was followed exactly until Orbit 90 (Site Exposure control began with mission design,
IIP-11). Sites IIP-11 and -12 were then shifted and the preparation of a lighting strategy study
one orbit later, to Orbits 91 and 94, and Site to determine the effects of illumination on the
IIS- was moved to Orbit 95, for better target signal-to-noise ratio for Lunar Orbiter photog-
coverage. These changes required some re- raphy. At that time, the nominal mission geometry
scheduling of film processing, but presented no was used to determine a set of nominal shutter
operational difficulties. Minor changes in pro- speeds that were used for planning purposes,
cessing times were made to correct for process- and as operational inputs prior to on-line deter-
ing rate veriations and to maintain the scheduled minations.
readout index. The observed readout index was
the final criterion for film management, which Vertical Photography
was entirely satisfactory throughout the mission.
The photo quality prediction computer program
2.5.2 SPACECRAFT OPERATION AND (QUAL) was again used, as in Mission I, to
CONTROL assist in determining shutter speeds for all
vertical photography. Since this program re-
2.5.2.1 Photo Sequence quires considerable run time, especially when
time-shared, an additional option was made
All photo command sequences were checked available that computes only the predicted
on-line for possible constraint or logic viola- spacecraft film densities. This output was avail-
tions. Such factors as V/H sensor operation near able in minutes and provided preliminary
the terminator were checked and, if necessary, determinations of the optimum shutter speed.
sequence modifications were recommended. In the case of secondary sites, the final shutter
Most sites were taken with a standard sequence, speed was generally determined from these
similar to that used for Mission I. predicted film densities.
In many cases, a shutter speed yielding densities
2.5.2.2 Camera-On Time Determination in the 0.4 to 0.7 range could be selected and no
further analysis was required for photography
To obtain an actual exposure as close as possible control. In borderline situations, QUAL was
to the time desired, the stored program command run with the cone and slope resolution options
(SPC) camera-on time was calculated as follows: for the shutter speeds in question. Shutter speed
was then selected for best resolution. A nominal
The exposure time desired was first obtained l-sigma smear value (125 microns/second at
from Flight Path Analysis and Command FPAC). 3-degree crab angle) was used for these cases.
For single frame, V/H sensor-off photos, this Albedos determined by the U. S. Geological
time was entered into the stored program se- Survey were used for most sites.
quence. Due to the nature of the V/H sensor
cycle, a half-frame bias was introduced to center High light transmission of the 80-mm lens, rela-
the actual exposure times about the desired tive to the 610-mm lens, greatly complicated
78
Table 2.5-l: Film Budget Plan
PHASE: Orbital (SEAL)
Readout
- - _1
51 11 2 -7 to +4
P-l 5-20
52 19 1 21
S-l 21-24
s-2 53 2 ).5M 0.5 3 23 25-28 5 41
s-2 54 2 ).5MG 1.0 5 25 29 - 32 7 B1
s-3 55 2 ).5G 1.5 4 27 33 0 ClA2
s-4 56 2 ).4GW 1.9 3 29 34 11 *2
P-2 57 4 ).4W 2.3 7 33 35-42 13 Dl Gs
58 3 1.9W 3.2 4 36 17 D2
l’-3 59 8 ).4M 3.6 4 44 43-50 20
79
Table 2.5-l: Film Budget Plan (Continued)
3’
/d Readout
74 T 2 1M
).9MG
14.1 5
15.0 2
87
91 95
69
71
70
s-9 75 8 4 72~ K2
P-7 76 8 2 1.9G 15.9 8 93 96-103 75 76~
P-7 77 4 1GW 16.9 12 97 104-111 77 78 Ml
78 4 1W 17.9 8 101 81 82 M2
s-10 79 4 1W 18.9 5 105 112 85 86 Nl
P-8 80 8 1M 19.9 5 113 113-120 89 90 N2
P-8 81 4 1M 20.9 9 117 121-128 97 98 01
P-8 82 4 1MG 21.9 13 121 129-136 101 102 02
s-11 83 4 1G 22.9 10 125 137 105 106 Pl
84 8 5 1GW 23.9 5 130 109 110 P2
P-9 85 8 4 1W 24.9 9 134 138-145 114 115 Ql
P-10 86 8 5 1w 25.9 12 139 146- 153 118 119 Q2
P-10 87 4 1M 26.9 16 143 154-161 123 124 Rl
88 1 4 1M 27.9 12 147 127 128 R2
s-12 89 4 1MG 28.9 9 151 162 131 132 Sl
90 4 1G 29.9 5 155 135 136 S2
P-11 91 8 IGW 30.9 5 163 163-170 139 140 Tl
P-11 92 9 1w 31.9 4 172 171-178 147 148 T2
P-12 93 4 1W 32.9 8 176 179-186 156 157 Ul
P-12 94 4 1M 33.9 12 180 187-194 160 161 u2
95 1 3 1M 34.9 9 184 164 165 Vl
s-13 96 3 1MG 35.9 7 186 195 167 168 I72
s-14 97 1 2 0.9G 36.8 6 188 196 170 171p W
P-13 98 8 4 1GW 37.8 10 192 197-204 172 173 W1
P-13 99 8 4 1w 38.8 14 196 205-212 176 177 X2
s-15 .oo 1 4 1W 39.8 11 200 213 180 181
S-16 ,Ol 1 6 1M 40.8 6 206 214 184 185 xi
s-17 102 1 3 1M 41.8 4 209 215 190 191
LO3 16 7b 1M 13 216 200 201
LO4 8b 1G 5 224 208 209
LO5 4 0 226
LO5
- 3 - 0
*Notes: (By Orbit Number) will be scrubbed when it interfers with neces-
General: Duration of readout is based on giv- sary tracking or mission control.
ing the second“ readout - drive on” co~nmancl
as early as 30 minutes after completing the re- P in “Frame Numbers” “Readout” indicates
verse attitude maneuver following pliotog- partial frame.
raphy, whichever is later. Initials following numbers in “Event” “Read-
out” signify the DSIF station in receiving
Although readout is indicated every orbit, such position; G = Goldstone, M = Madrid, W =
an accom~~lishment is not committed. Readout Woomera.
80
exposure control. In several cases, satisfactory For convenience, one nomograph was modified
exposure could not be achieved in both cameras. to indicate spacecraft film densities for each
When this occurred for a multiple-pass site, shutter speed. Results obtained with the nomo-
the shutter speed was changed between orbits graph generally appeared valid when compared
to optimize exposure for each camera in at least to the reassembled pictures available for in-
one orbit. QUAL did not fully reflect this flight analysis.
problem in that the 80-mm results had to be
discounted slightly.
Average-Density Data
81
Table 2.5-2: Lunar Orbiter Mission II - Prime-Site Parameter Summary
Site elected Phase Angle Altitude Shutter Rad. Smear
No. 4lbedo Decrees KM Speed Dose Nominal
NASA Jominal (ornina gominal
dission Predicted Actual Mission Predicted Actual Missidn Actual Rads Sate* Angle**
referred
:IP-1 0.088 74.5 72.9 72.9 51.2 48.0 47.4 l/25 l/25 1.0 125 60”
LIP-2 0.088 68.4 68.0 67.8 48.3 45.0 44.6 l/50 l/50 1.0 125 60”
HP-3a 0.084 76.3 75.6 75.6 50.5 48.0 47.5 l/25 l/25 1.0 125 60”
LIP-3b 0.084 76.3 74.4 74.4 50.5 46.3 45.7 l/25 l/25 1.0 125 60”
LIP-4 0.111 78.6 77.7 77.7 52.3 50.5 49.2 l/25 l/25 1.0 125 60”
HP-5 0.086 68.8 68.8 69.1 46.7 43.6 42.9 l/50 l/25 1.0 125 60”
HP-6a 0.087 61.0 62.6 62.6 50.9 48.5 47.0 l/50 l/50 1.0 125 60”
HP-6b 0.087 61.0 61.1 61.1 50.9 50.9 49.1 l/50 l/50 1.0 125 60”
IIP-7a 0.098 69.7 70.1 70.2 44.2 42.2 41.0 l/50 l/50 1.25 125 60”
IIP-7b 0.098 69.7 68.4 68.7 44.2 42.8 41.6 l/50 l/50 1.25 125 60”
IIP-8a 0.092 60.8 63.1 63.1 51.2 47.2 47.0 l/50 l/50 1.25 125 60”
IIP-8b 0.092 60.8 61.7 61.7 51.2 50.5 49.6 l/50 l/50 1.25 125 60”
IIP-8c 0.092 60.8 60.2 60.2 51.2 53.3 52.6 l/50 l/50 1.25 125 60
IIP-9 0.093 65.8 66.1 66.1 46.8 45.1 44.7 l/50 l/50 1.25 125 60”
IIP-1Oa 0.091 77.8 76.9 76.9 48.3 44.8 44.4 l/25 l/25 1.25 125 60”
IIP-lot 0.091 77.8 75.5 75.5 48.3 43.8 43.4 l/25 l/25 1.25 125 60”
IIP-1 la 0.105 62.1 62.9 62.9 52.5 51.0 52.0 l/50 l/50 1.25 125 60”
III’-111: 0.105 62.1 61.5 61.5 52.5 54.1 55.4 l/50 l/50 1.25 125 60”
IIP-12a 0.087 74.1 72.9 72.8 47.6 43.6 44.2 l/25 l/25 1.25 125 60”
IIP-121: 0.087 74.1 71.4 71.4 47.6 43.9 44.9 l/25 l/50 1.25 125 60”
IIP-1321 0.073 71.1 71.8 71.8 49.2 45.7 45.3 l/25 l/25 1.25 125 60”
IIP-131: 0.073 71.1 70.4 70.4 49.2 46.5 46.4 l/25 l/50 1.25 125 60”
I
* Microns I Sec.
** This angle is QUAL Input angle and represents smear 30 degrees off flight direction.
Table 2.5-3: Secondary-Site Parameter Summary
2.5.2.4 Photo Time Correlation TIML computer run. The TIML program
makes the necessary corrections to obtain
The following procedure was adopted to obtain true GMT. As modified for Mission II,
correct GMTs for each photo frame. the TIML output lists the input clock
1) After completion of readout and process- time, the corresponding GMT, and actua-
ing of the GRE film, the video engineer tion time of the two shutters.
read the recorded time code and reported 4) After obtaining the GMT, the photo data
it to the photo data analyst as part of his analyst entered it on the photo identifica-
preliminary analysis. tion form. The completed form was then
2) The photo data analyst then converted mailed to Eastman Kodak in time to be
the binary number represented by the available prior to the arrival of the GRE
time code to decimal clock time using film from the DSSs. The times were sub-
conversion tables. sequently checked against the scheduled
3) The decimal clock was furnished to the camera-on times by the photo acquisition
programmer analyst as the imput for a specialist.
83
NORMAL ALBEDO
PHASE
ANGLE 0.04 0.06 0.08 0.10 0.12 0.14 0.16
Index Line- Shutter Speed at
85c f.5.6 SO-243
Bimat Pr ocess
To determine camera shutter speed, lay
a straight line from the phase ongle through
80’
the angle to the index line and a
horizontal line from the intersection with
the index to the normal albedo of the
75c target area.
7oc
65c
60”
55c
I _
I -
I-
) -
l-
I -
i -
i -
I -
j -
0.2 1 _
0.1 I -
(lh
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 I./ I.U I.Y z.u Z.I
86
Figure 2.5-3: Photo Quality Predict Program (QUAL) Output, Site IIP-I
--ORBIT NUMBER 0 SITE NUMBER. 1 - FLIGHT NUMBER -2 TIME OOO/OO/OO/OO RUN NUNBER 00000000
INITIAL CONDITIONS - ALBEOO= 0.088 PHASE ANGLE= 72.9 OEGREES ALTITUDE= 47.4 KILOMETERS
RAOIAT ION= 1.0 RADS SMEAR RATE= 125. MICRONS/SEC SMEAR ANGLE= 60.0 DEGREES
PREDICTED S/C FILM DENSITY FOR 24 INCH CAMERA AT ALL SHUTTER SPEEDS - SLOW 0.76 NEDIUW= 0.40 FAST= 0.27
PREDICTED S/C FILM DENSITY FOR 3 INCH CAMERA AT ALL SHUTTER SPEEDS - SLOW= 1.00 MEDIUM= 0.54 FAST- 0.31
SLOW SHUTTER SPEED SLOPE TARGET GRE OUTPUT POINT 24 INCH LENS
_.._._______... !TERATroN.Nun.~ER~.P _____._.___ -----_S_LP_PE.~~~-!-~O.~~~~~.~~ .__....._. SIGNAL-~TO-NO!SE-R*IIOI-_757 __.._..._____________
ITERATION NUMBER= 1 SLOPE= 0.13 DEGREES
SLOW SHUTTER SPEED CONE TARGET OGRE OUTPUT POINT 24 INCH LENS
.- .------------ ITERATION NU#DER=
ii~~~~fon’NUM.~SR’-.-i 1 . . . .._...... DIAMETER= 1.29 METERS SIGNAL-TO-NOISE
Siiiii~r~~.~..~b~~~~~~~~.~~~-~-.~-.---~~~i~~~~~~~~~~~~~i~~..~~~i~~~~~~~~~~~~--- RATIO- 6.24 _______ - _________
Figure 2.5-4: Photo Quality Predict Program (QUAL) Output, Site IIP-2
.---- .^.. ~. ---. .------.---
ORBIT NUMGER 0 .. SITfm_NU.?tiER 2 --FLIGHT NUHGER 2 TIME
- -~__ OOO/OO/OO/OO
..- -. RUN NUMBER 00000000
INITIAL CONDITIONS - ALEEDO= 0.088 PHASE ANGLE= -67,cOEGREES ALTITUDE= 44.6 KILOHETfRS. _
PREDICTEU S/C FILM DENSITY FOR 24 INCH CANERA AT ALL SHUT.TER SPEEqS.~_S~Oy=-~O.SS KEDIUH= 0.52 FAST= 0.30
PREOICTkD S/C FILH DENSITY FOR 3 INCH CAMERA AT ALL 5HUTTERm_SFEECISI~m SLOW= l.?O- MEDlU_n= _. 0.71.-. FAST= 0.38
* .-. * l
.--. * *- OPTIONS
-.. . AND RESULTS * l + l * ..- ~__ -- .-
MEDIUM SHUTTER SPEED SLOPE TARGET GRE OUTPUT POINT .. 24 INCH LENS
ITERATION NUJ’.BER= 0 SLOPE= 1.00 DEGREES SICNALLTD-NOISE- RATIoi 4.11
ITERATION NUbBER= 1 SLOPE= D-24 DEGRE? -- --.--.-.--_. -_ --- --..--- .-
_ MEDIUM SI’UTTEX SPEED COHE TARGET _,_ GRf .OUTP_U_T PO1 NT 24 INCH -LENS __ __.. ___ .--- - _-
ITERATION NUEBER=- 1 DIAMETER= 1.11 HtTERS SIGNAL-TO-NOISE RATIO= 3.98
ITCRATION .dJHEfR= 2 DIAMETER= 0.96 Y,ETE2S SItiNAL~T~NGISE~RATIO= 3-03
ITfRATION NUMBER= 3 OIANETER= 0.96 MfTERS
MEDIUM SHUTTER SPEED SLC’PE TARGET GRE OUTPUT POiNi -- ---I%--&- LENS
_. . .IT.fHATION. NUKGEP= ” _ _ SLIJPEF ..l-mG(j-GF,GRECS. SIGNAL-TD-NOISE
__. - RATIO- ____ 0.45-. _-- ------
ITERATION NIJXBER= 1 SLOPE= 2.13 DEGREES
87
Figure 2.5-5: Photo Quality Predict Program (QUAL) Output, Site IIP-3
_--__--- ..--. - - .-.--.. ________-.-. -~_
ORBIT NUMBER
-__- 0
-.----- SITE NUHBER 3 FLIGHT NUMBER 2 TIME OOO/OO/OO/OO
--__ RUN
- NWBER
--__ 00000000
.-_-.-
.-INITIAL CONDITIONS
- -. - ..__ - _--- ALfiEDO=
-. ._..._.0.084 PHASE ANGLE= 75.6 DEGREES ALTITUDE=__ 47.5 - KILOMETERS
~~~ .._. _ ~
PREDICTED S/C FILM OENS!T’Y FOR _ ?-INCH CA~~RK_~T ALL SHUTTER SPEEDS - SLOW 0.80 HEDIUM=
___.-- 0.43 -~. FAST= 0.28
-.-- * * +
-.-.__.-__.. * * OPTIONS AND RESULTS * * * * * ._---
SLOY SHUTTER SPEED SLCPE. TARGc_T - - ‘7% NJ??‘!?-_P!‘LM-- mZ%AfltH-LB’- ~- ._ _. - ____ _._. ._
ITERATION NUb!BER= 0 SLOPE= 1.00 SEGREES SIGNAL-TWNOISE RATIO= 8.82
ITERATION. NL;P.?BER= l- -. _. .-SLOPE= 0.11 DEGREES
Figure 2.5-6: Photo Quality Predict Program (QUAL) Output, Site IIP-4
- ---~--- -_--.
ORBIT NWBER 0 SITE NlJ?EER 4 FLIGHT
-. ._ NUKfZ:R
--- 2 TIME OOO/OO/OO/OO
--__- .--__-- RUN NIJKBER _-_-_
00000000_ . ..__.
_. LUNAR LONGITUDE= 999.99 LUNAR LATITUDE= 999.99 -__ .-..- - -.. --- __....
INITIAL CCNOITIONS - ALGEOO= ~2.111 PHASE ANGLE= 77:LC)EGRE:S ALTITUDE=-- ..- 49.2
_ KILOMETERS
_. .___ .-
PREDICTELI S/C FILE DENSITY FCI: 24 INCH CAHERA AT ALL SHUTTER SPEEDS y SLOi+_O.65 -~ Y.EGIUM= 0.36 FAST= 0.26
PREDICTED S/C FILM DENSITY FUK 3 INCH CAt?ERA. AT ALL._SHvTTER SPEEp>:.SLOW= 0.8-r_ N~O!&!!.O.46 FAST= -0.29
88
I --
Figure 2.5-7: Photo Quality Predict Program (QUAL) Output, Site IIP5
-. ..-..-. -.. .~ .-_ ~~
..- ORBIT
- -... NUMDER
-.. 0 SITE NUKBER 5 FLIGHT NUK3ER 2 TIME OOO/OO/OO/OO RUN NUMRER 00000000
.!=+QIAJION= 1.0 RADS ShEAR RATE= 125. RICRD:b$/SEC: --SKEAR ANGLE= 60.0 DEGREES
PREDICT&l S/C FILM OEKSITY FOR 24 INCH CAHERA AT ALL SHUTTER SPEEDS - SLOW= 0.90 --. WEDIUH=
- . -.--.--- 0.48 FAST=
. . 0.29
--.-..
._.* * ..-.
* l * OPTIONS AND RESULTS * * * l * __.. -_-
SLOW SHUTTER SPEED SLOPE TARGET GRE OU_TFUT_POTN_T_ _ _ ~4_I_N_cm_LF.tjS.- -. ____ __. ._. _ _
ITERATION NU?BER= 0 SLOPE=. l-00 DEGREES SIGNAL-TD-NOISE RATIO= 5.12
ITERATION NUKBER= 1 SLOPE= O-1.9. DEGREES -~ ~~-..---~
SLOk SWTTER SPCED CONE TARGET GRE_. DUT_PUT POINT 24>CH -LENS
ITERATION NU.?fiEi:= 1 DIAHETtd= 1.31 RETFRS SIGNAL-TD-NOISE RATIO= 6.28
1T:RATION NUK:aER= 2 DIAHETER= 0.91 KZTERS SIGNA_L--TO--HOI.SE._RATIO=~_2.99_
ITERATION NU%BER= 3 DIAMETER= 0.91 KtTERS
Figure 2.5-8: Photo Quality Predict Program (QUAL) Output, Site IIP-6
- _-
ORBIT NUMBER 0 SITE NUMBER 6 FLIGHT NURDER 2 .-TIME bOb;OO/OO/OO RUN NLiDER bOOOOOO0
INITIAL CONDITIONS - ALBEOO= 0.087 PHASE ANGLE= 62.6 OEGREES ALTi;UDE= 47.0. K;LOWETERS -
RADIATION= 1.0 RADS SHEAR RATE= 125. ~ICRDNS/SEC SHEAR ANGLE= 60.0 DEGREES-
PREDICTED S/C FILM DENSITY FOR 24 INCH CAMERA AT ALL SHUTTER SPEEDS - SLOW= 1.12 MEDIUM= 0.63 FAST= 0.35
PREDICTED S/C FILM DENSITY FOR 3 INCH CAMERA AT ALL SHUTTER SPEEDS - SLDi= 1.36 HEDIUK=-0.85 FAST= 0.45
..-
. . . . . OpTI& A&, RESULT; I l . ; .- ----- --.-- --- --
HEDIUH SHUTTER SPEED SLOPE TARGET GRE OUTPUT .POINT 24 INCH LENS
ITERATION NUMBER= 0 SLOPE= l-00 DEGREES SIGNAL--TO-NOISE RATIO= - 3.81 --- -
ITERATION NUN6ER= 1 SLOPE= 0.26 DEGREES
MEDIUM SHUTTER SPEED CONE TARGET GRE CUTPUT b&NT 24 INCH LENS
ITERATION NUMBER= 1 DIAKETER= l-17 KETERS SIGNAL-TO-NOISE -RATI&= 3-20 -
ITERATION NUKBER= 2 DIAMETER= 1.13 METERS
89
Figure 2.59: Photo Quality Predict Program (QUAL) Output, Site IIP-7
____. - -_._ .__.__- ..-. - -..- .-
ORBIT NUHBER 0 SITE NUMBER 7 FLItHi hiJHBER 2 TIME OOO/OO/OO/OO RUN NUMBER OOOOOOO~-
.-_. -. -
LUNAR LONGITUDE= 999.99 - LUNAR- LATI-TUDE= 999.99
- .-. _..- _. . .
INITIAL CONDITIONS - ALBEDD= 0.098 PHASE-ANGLE= 70.2 DEGREES ALTITUDE= 41.0 KILOMETERS
_ __ _ - _ -. _
RADIATION= 1.2 RADJ - - SMEAR RATE= 125. -KICROt&SEC SHEAR--ANGLE= -60.0 DEGREES
--
‘PREDICTED s/c’ FILM DENSITY FOR 24 INCH CAMERA AT ALL SHUT~R SPEEDS - SLOY= 0.95 MEDIUM= 0.51 FAST= 0.30
PREDICTED S/C.FILM DENSITY FOR 3 INCH CAMERA AT ALL SHUTTER SPEEDS - SLOW= 1.26 BEbIUH=~~O.7i’-~FAST= 0.38
__.__.. - 1- _..-- _. . _. _ -_ - ._ -_ ._ .-..
. . . . . OPTIONS AN0 RESULTS l . . . l
--
MEDiUW--SHUTTER -SPEED SLOPE TARGET GRE OUTPUT POINT- 24 INCH LENS
.~ ITERATION NURBER= cl SLOPE= l.OC DEGREES ..-SIGML-TO-!dOISE RATIO= 5.45 _ _
ITERATION NUWBER= 1 SLOPE= 0.18 DEGREES
._ -
HEDIUH SHUTTER SPEED CONE TARGET GRE OUTPUT POINT 24 INCH LENS
,ITERATlON NUMBER= 1 DIAMETER= 1.02 KETERS. -.. - SIGNAL-T&NOISE RATIO= 4.51
ITERATION NUMBER= 2 OIAMETER- 0.83 P.ETERS SIGNAL-TD-NOISE RATIO= 3.03
ITERATION NUHBER= 3 DIACIETER= 0.83 HETEP.S -.. -
- IlEDLU~..SHUTTER SPfED SLOPE TARGET. GRE CUTPUT-PDINT . -.BD ,W -LENS - - _.-. - _-... .._.., _
ITERATION NUYBER= 0 SLOPE= l.OC DEGREES SIGNAL-TD-NOISE RATIO= 0.62
I TERATILIN NUKBER= 1 SLOPE= 1.56 DEGREES -. -. .-. .- .-_
-Hf.DIlJH SHUTTER SPEED CONE TARGET GRE DUTPUT POINT-- 80 NM LENS - -.-- - ..-
ITERATION NUMBER= 1 DIAMETER= 7.74 METERS SIGNAL-TO-NOISE RATIO= 8.84
_.._. _ .-.-. ITERATION NURBER= 2- .-.-DIAMETER= -45lXETERSp ~(;~L-$&+&QI~4~JJx-~- - -.. --.- ..-
ITERATION NUMBER= 3 DIAIIETER= 4.79 METERS
Figure 2.5-10: Photo Quality Predict Program (QUAL) Output, Site IIP-8
ORBIT NURBER 0 SITE NUMBER 8 FLIGHT NUMBER 2 TIKE GOO/CO/OO/OO RUN NUMBER OOCOOO50
INITIAL CONCITIONS - ALBEDO’ S-092 PHASE ANGLE= 61.7 DEGREES ALTITUDE= -49.6 KILOFETERS
RADIATION= 1.2 RADS SPEAR RAT;=‘- 125. MICRONS/SEC SMEAR AKGLE= 6C.0 DEGREES
PREDICTED S/C FILM DEKSITY FOR 24 INCH CAMERA AT ALL SHUTTER SPEEDS - SLOW= 1.18 MEDIUM= 0.70 FAST= 0.38
PREDICTED S/C FILM DENSITY FCR 3 INCH CAMERA AT ALL SHUTTER SPEEDS - SLOW= 1.43 MEDIUM= 0.92 FAST= 0.49
MEOIUR SHUTTER SPEED CONE TARGET GRE GUTPUT POINT 24 INCH LENS
ITERATION NWBER= 1 DIAMETER= 1.23 PETERS SIGNAL-TO-NOISE RATIO= 3.02
ITERATION NUMBER= 2 DIACETER= 1.23 METERS
HEDIUH SHUTTE? SPEED SLOPE TARGET G’iE CUTPUT POINT 30 ny. LENS
ITERATION NUXiiER= J SLOPE= l.OC DEGREES -SIGblAL-TC-NOISE RATIO= 0.24
ITERATION NUbEER= 1 SLOPE= 3.81 DEEREiS
90
Figure 2.5-11: Photo Quality Predict Program (QUAL) Output, Site HP-9
_
ORBIT NUMBER 0 SITE NUNBER 9 FL&T NURbER 2 TIME OOO/OO/OO/OO RUN NUNBER 00000000
INITIAL CONDITIONS - ALBEDO= 0.093 PHASE ANGLE= 66.1 DEGREES ALTITUDE= 44.7 KILOWETERS
RADIATION= 1.2 RIDS SMEAR R;TE= 125; iICd0~S/sEt SnEAR iNG;E= 60.0 DEGREES
PREDICTED S/C FILM DENSITY FOR 24 INCH CANERA AT ALL SHUTTER SPEEDS - SLOW= 1;05 NEDIUII= 0.58 FAST= O-33
PREDICTED S/C FILM DENSITY FOR 3 INCH CAHERA AT ALL SHUTTER SbEEDS - SLObkl.29 MEDIUM=. 0.78 FAST= 0.42
_ _.-.. ._.~. -..
l l l l l OPTIDNS AND RESULTS * l l l l
MEDIUN SHUTTER SPEED SLOPE TARGET GHE OUTPUT d&NT 24 INCH LENS
ITERATION NUHBER= 0 SLOP& l.OC OEGREES --SIGNAL-TO-NOISE RATIO= 3s6B
ITERATION NUMBER- 1 SLOPE= 0.27 DEGREES
- ~. _
NEDIUM SHUTTER SPEED CONE TARGET GRE OUTPUT POIN;- 24 INCH LENS
ITERATION NUMBER= DIAMETER= l-11 RETERS SIGNAL-TC-NOISE RATIO= 3.81 -.
ITERATION NUMBER= : DIAMETER= 0.99 METERS SIGNAL-ID-NOISE RATIO= 3.02
ITERATION NUMBER= 3 OIARETER= 0.96 METERS
MEDIUM SHUTTER SPEED SLOPE TARGET GRE CUTPUT -POINT- _ ..-80 “Y _ LE#S~ _ _.
ITERATION NUMBER= 0 SLOPE= 1.00 DEGREES SIGNAL-TD-NOISE RATIO= 0.37
ITERATION NUHBER= 1 SLOPE= 2.56 DEGREES
Figure 2.5-12: Photo Quality Predict Program (QUAL) Output, Site IIP-10
-.-. -
ORBIT IUNEER 0 SITE NURBER 10 FLIGHT NUNBER 2- - -1INE-oDO/OO/DO/OO . -RUN NUHBER DO000000
INITIAL CONDITIONS - ALBEDC= 0.091 PHASE ANGLE= 76a9 DEGREES ALTITUDE= 44.4 KILONETERS
RADIATION= 1.2 RADS StiAR &ATE=.. lZ5, MICRONS/SEC. SNEAR ANGLE= 60-D DEGREES
PREDICTED S/C FILN DENSITY .FOR 24 INCH CAflERA AT ALL SHUTTER SPEEDS - SLDY= O-58 flEDI,,+,= 0.33 FAST= 0.25
PREDICTED S/C FILM DENSITY FOR 3 INCH CANERA AT AU SHUTTER SPEEDS - SLOW= 0.78 MEDIUR= 0.42 FAST= O-27
SLOY SHUTTER SPEED SLOPE TARGET GRE OUTPUT PDINT 24 INCH LENS
ITERATION NUKBER= 0 SLOPE= l.L'C DEGREES SIGNAL-TO-NOISE RATIO= 7.27
ITERATION NUHBER= 1 SLOPE= 0.12 DEGREES
91
Figure 2.5-13: Photo Quality Predict Program (QUAL) Output, Site IIP-11
_ _ _. . ^ -.
ORBIT’ NUHBER 0 SITE NUMBER 11 FLIGHT NURBER 2 TIME OOO/DO/OO/OD RUN N;WBER 00000000
INITIAL CONDITIONS - ALBEDO= 0.105 PHASE ANGLE= 62.9 DEGREES ALTITUDE= 52.0 KILOIIETFRS
RADIATION= 1.2 RADS &EAR -RATE= 125. HICR;NS/SEC WEAR ANGLE= 6&O DEGREES
PREDICTED s/c FILM DENSITY FOR 24 INCH CAMERA AT ALL SHUTTER SPEEDS - SLOY= I..24 MEDIUM= 0.74 @AST= 0.40
PREDICTED S/C FILH DENSITY FOR 3 INCH CAMERA AT ALL SHUT;;; SPEEDS - ;Lbh’= 1.48 HEDi;H=~~0.97 FAST= 0.53
HEDIUH SHUTTER SPEED SLOPE TARGET GRE CUTPUT POINT 24 INCH LENS
ITERATION NUMBER= 0 SLOPE= 1,OC DEGREES ..SIGNAL-TO-NOISE RATIO= 2.99
ITERATION NU+!!BER= 1 SLOPE= 0.33 DEGREES
MEDIUM SHUTTER SPEED CONE TARGET GRE CUTPUT PO;NT- 24 INCH LENS
ITERATION NUMBER= 1 DIAMETER= 1.27 KETERS SIGNAL-To-NOISE RAT1 0= 2.97
ITERATION NURBER= 2 DIAMETER= 1.28 METERS
MEDIUM SHUTTER SPEED SLOPE TARGET GRE CUTPUT POINT a0 HP: LENS
ITERATION NUMBER= 0 SLOPE= LOG DEGREES. --.-U&NIL-TO-NOISE RATID= 0.25 -..
ITERATION NUMBER= 1 SLOPE= 3.65 DEGREES
Figure 2.5-14: Photo Quality Predict Program (QUAL) Output, Site IIP-12a
ORBIT NUMBER 0 SITE NUMBER 120, FLIGHi NU-iBER 2 TIME OOO/~O/OO;bO ‘i&N N;MkER bOOOOOOb
.-
LUNAR LONGITUDE= 999.99 L-UNAR LAT;TUDE= 999.99 .
INITIAL CONDITIONS - ALBEDO= 0.087 PHASE ANGLE= 72.8 DEGREES ALTITUDE= .44.2 KILOMETERS
_----. -
RADIATION= 1.2 RADS SHEAR RATE= 125. biIcRO~s/sEt SWEAR-ANGLE= bC.0 DEGREES
PREDICTED S/C FILM DENSITY FCR 24 INCH CAWERA AT ALL SHlJTT;R SPEEDS - SLOY= 0.76 REDIIJM- 0.40 FAST= 0.27
PREDICTED S/C FILM DENSITY FDR 3 INCH CAMERA AT ALL SHUTTER SPEEDS - SLOY= 0.99 HEDIUH= 0.54 FAST= 0.31
.~
l + l l l OPTIONS AND RESULTS l l * . .
SLDY SHUTTER SPEED SLOPE TARGET GRE OUTPUT POINT 24 INCH LENS
ITERATION NUV5ER= 0 SLOPE= l-01; DEGREES .- -SIGNAL-TO-NOISE RATIC= 6.24
ITERATIDN NUMBER= 1 SLOPE= 0.16 DEGREES
-
SLOW SHUTTER SPEED CONE TARGET GRE CUTPUT POINT-- - 24 INCH LENS
ITERATION NUHBER= 1 DIAMETER= 1,2i KETERS SIGNAL-TD-NOISE RATIO= 6.21
ITERATION NUyBER= 2 DIAMETER= 0.83 FETERS SIGNAL-To-NOISE RATIO= 2.96
ITERATION NUNBER= 3 DIAMETER= 0.84 METERS
92
Figure 2.5-15: Photo Quality Predict Program (QUAL) Output, Site IIP-12b
-___ --.. -.-..--_.
ORBIT NUMGER 0 SITE NUMBER x2b FLICHT WDDER 2 TINE 9DO/DG/DG/OO RUN NUNEER OOOOOOGO
PREDICTED S/C FILN DENSITY FOR 24 INCH CARERA AT AU STUTTER WEEDS - SLOW= O-82 MEDIUM= 0-M FASi= 0.20
l REDICJED f/C FILN DENSITY FOR 3 INCH CANMA AT ALL STUTTER SPEEDS - SLDY- l-06 MEDIUN- 0.59 FAST- 0133
--.-.___.--_._---_.--_.- -- ____. ~.______ ._-. .--
. l . l . OPTIONS AND RESUtTS . . * . a
_-- ..-. _ ___ --.- .--- ~--_-__ --...- ..--- ..-- --...-- ~~
NEOIUN SHUTTER SPEED SLOPE TARGET 6RE OUTPUT POW-- 24 INCH
- LENS
~. -..-. -----Im3lArJoNnuacERlJ-- .-- tlnPE=-LDoNPFFCm -
ITERATION NUNBER- 1 SLOPE= 0.23 DEGREES
~_~
NEOIUR SIWTTER SPtEO COWE TAR6ET GRE MPUT POINT 24 INCM LENS
--.- -- x-2----FPI1-91* Is&..RAv----.-
ITERATION NUMER= 2 DIAMETER= O-96 METERS SIGNAL’TD-WOISE RATIlt 3sDt
-.--___ eBEN=J---- mo---- ___-__--
Figure 2.5-16: Photo Quality Predict Program (QUAL) Output, Site IIP-13a
-.
ORBIT NUMBER 0 SiTE NUNGER 13h FLIGHT NUMBER 2 TIME 800/00/00/00 RUN NUNBER OOOOiOOi
INITIAL CONOITIP1S mi ALGEDD= 0.073 PHASE ANGLE= 71.6 DFGREES ALTITUIE- 45.3 KILONETERS -
__- ..- -.. -
RAOIhTIW= 1.2 RAOS SWEAR RATE= 125. NICRDNVSEC SMEAR AN6LE= 60.0 OECRECS
PREDICTED S/C FILN DENSITY FDR 24 INCH CANERA AT ALL SHUTTER SPEEDS - SLOW= O-69 MECIUH= 0.37- FAST= 0.26
PREDICTED S/C FILN DENSITY FOR- 3 INCH -CAMERA AT ALL SHUTTER SPEEDS - SLOW 0;91 MEDIUM= 0.49 FAST= b-30 -
~LDY SHUTTER SPEED SLOPE TATkiT 6RE OUTPUT POINT 24 INCH LENS
- IIERAJION NUHBEP= D SLOPE= - l&O DEGREES -- .-SlGNAL=TD=ND ~$-.&u&--.~qt--- - ---.-
ITERATION NUNGER= 1 SLOPE= 0.17 DEGREES
_ . -. .- _ ..- .._..- ._ ---.-.._--.__--..--_---- __-__ _____-.- --
SLOW SHU~TER~SPEED CONE TARGET 6RE OUTPUT POINT 24 INCH LENS
_IERAlIDY NUNGER- 1_ --. DIANFTFE= 1-7511EIw-. __ Z,I- I&A50-p- ----
ITERATION NUMBER= 2 DIAMETER= O-85 METERS SIGNAL-TWNOISE RATID= 2.96
.-IIERATlDtLdLLINDEft=3~ .-LuAnEuR=-n-nh.. .-.-~ .-- .-.
- .-- -SLDN SNUTTER-SPGGD ND&R= -. CDNE -TARGE-T GRE -DUTPuFpBuA- pnn - --LEWs- -----__ _..-__--.._
ITERATIGN 1 OIAMETER~ 10.71 METERS SIGNAL-TD-NOISE RATID= 14.19
-. -IT-.NUwBER=.Z .- dlANEILR= --4&J4ETE ‘c-OISfS4ATI~~---
ITERATION NUNBER= 3 DIANETER= 5.44 METERS SIGN*L-T~-NOISE RATI* 3.16
_ .-UEIUTIOU NUI!lGER=e 4 . ..DIANETER=. -5-30 NGTEK.-- -. -... --- ._... .-~ .--_. ---- -... --. _-
93
Figure 2.5-17: Photo Quality Predict Program (QUAL) Output, Site IIP-13b
._ _-..._ .-. -_ _. ._-. -- ..__._ ._ - _ -_ -..--- ..-..._...-- --..--.-._----.--_.-.--- ._.. __..- __ ..__.,___
ORBIT YUKRER
c - .-. _ ._ - P --. “T’““““‘” l3 9 ..- “‘“..“““““- ‘- ._ .‘!:E2Yo.“!YY~-- --Y!” “““B-E”..~op_p”_“p” ._
LUNAR- LONGiTUDE= 999.99 LUNAR LATITUDE= 999.99
-.-. .- - .-.. - . - .-.-_._
c INITIAL--COROIT;kS - ALBEDD- 0.073 PHASE ARGLE= 70.4 DESREES ALTITUU? 46.4 KILORETERS
._... - _._... -..--...- -.-. --..---.-__ ..-- -__-___. --.---.----.--. -- ._____,_ ,__.__
RADIATION= l-2 RIDS SMEAR RATE= 125. MICRONS/SEC SHEAR ANGLE= 60.0 DEGREES
c _,._...-__-. _.--. .---
PiEDItTED S/C FILM -DENSITY F& 24. IN& CARERA AT ALL SHUTTER SPEEDS - SLOY=-.0-f4-11EDIUII; ~0.40 FAST= 0.27 --
__-_. - .._._ __---_- . . -..-... ..-...--..-- .-_ -
PREIiICTED S/C FILM DERSITY F& -i INCH CAHERA AT ALL SHUTTER SPEEDS - SLOW= 0.97 REDIuR= OiiT-~iii< -0.31
_ __. _. _ --- __ _-_-- -___.-.- .--- -- -------- ..--._ - .--. ----- .
l . . l . OPTIONS AND RESULTS . . l . .
.( -..
WEOIUKSWTTER SPEED SLOPE TARGET GRE OUTPUT POINT 24 INCH LENS
. .ITERATION-RUJtBER= 0 -- SLOPE= Itot- DEGREES- - --JIGNAL-Xk-NOISERATJO= -3.65 -
-I ..-
ITERATION NUWBER- 1 SLOPE= 0.27 DEGREES
- - .-- ..-- . - ---. ..-.--.- --_. -. ----- . - _ - .._ _. -
UEDIUR SHUTTER SPEED CONE TARGET GRE OUTPUT POINT 24 INCH LENS
c. -- _... -ITERAJIDN NJJJIBERr 1 --DIARETER=-L31 NETERS- -- .-. ~IGKAL-TO-NOU&RATIO=- 4-46 - - . _
ITERATION NLlRBER= 2 DIAHETER= 1.08 RETERS SIGNAL-TO-NOISE RATIO= 3.08
..~_ ILERATION MJRBER= 3 - _ -0 lAnmERsm~----- - ._-.~---. .- -. .--._ _
c- -.
-._. -.- nEm iJasHunER-spELa --- --sLopI-TARGEL------m-awpu-T-Td 0 a” ..46+JL-- --.._ - -.. - --... ._
ITERATION NUMBER= 0 SLOPE= 1.00 DEGREES SIGNAL-TO-NOISE RATIO= 0.49
‘C--.- . .._ ..- _ JIERAZIDYNUH8ER=1 -. -~IJpE~~g8~----.. ..- - ..-. .-.-- .-...- - ._ _
5.0
4.8
4.6
Ii te 1.e~
3 -
I
4.4 : c
4.2
24.0
J
I
t 3.8
3.6
3.4
3.2
3.0
!p 1
2.0
II
1.8
c 1.6 step 1
!j 1.4
!!!I
s 1.2
1.0 step 5
I I
step 9
SE--
TIME (GMT)
Figure 2.5-18: White Level and Gray Scale Figure 2.5-19: White Level and Gray Scale
Variation Near Processing Defects Readout Variation Near Processing Defects Readout
Sequence 087 Sequence 097
94
5.C
4.8
4.6
4.4
2 4.2
6 4.0
>
' 3.8
CJ 36.
F? 3.4
2 3.2
2 3.0
Step 1
1 2.0
I --\
24
y3 1.8
2 > 1.b I
step 5
=5 5 1.4
0
5 2 1.2
k6 1.0
27 0.8
step 9
Y9 0.6 I I
0.5
Ei?:$z38’ I .
I
m 52
Figure 2.5-20: White Level and Gray Scale Figure 2.5-21: White Level and Gray Scale
Variation Readout. Sequence 122 Variation Readout Sequence 127
2.5.3.2 Decrease in White Level During sor stop lines or other Bimat processing defects
Readout were reported by the video engineer for these
A phenomenon, not reported earlier, became frames readout in sequences 115,116, and 117.
apparent during Readout Sequences 115, 2.5.3.3 Variation of Density as A Function of
116, and 117 (Refer to Figure 2.5-22). The W Signature
white level at the end of readout 115 was, re-
portedly, 4.3 volts. At the beginning of the next Focus of the line-scan tube affects the level of
readout, 116, the white level was 4.7 volts. the video signal during a scan across the width
During the 120-minute readout, the white level of a framelet. Ideally, the level would be con-
average value decreased steadily and ended at stant for a constant film density. However, the
4.1 volts. At the beginning of Sequence 117, in angular sweep of the light spot produces a
the focus stop position, the white level jumped variation in intensity. Optimum focus produces
to 4.5 volts. a small variation that takes the form of a low
rounded “W” on the GRE A-scope. This varia-
One gain increase brought this value up to 4.9 tion is reflected as a density variation across the
volts. Again the average white level decreased framelet on the reconstructed record. As a result
during readout and was 4.0 at the end of read- of the “W” focus pattern, the density variation
out. The probable cause of this is photomultiplier can range from a maximum of 2.0 in the peak
tube degradation. Various methods of compen- density to a minimum of 1.7. Therefore, care
sation are being considered for Mission III. was taken by the video engineer to make
The procurement specification states maximum measurements in a framelet that had a complete
“on” time of 93 minutes. But even before 93 gray scale within it. Even with this precaution,
minutes the decrease was considerable. The because of the nonsymmetry of the “A” pattern
gray scale data is too scattered to draw any ladn “A” framelet’s densities are the mirror
conclusions. If more data existed, it might be image of a “B” framelet’s), the spread in gray
possible to separate photo video chain (PVC) scales read from various framelets makes cor-
decrease from the change in density. No proces- relation difficult.
95
5.C After 1 3ain Increase1
4-E
4.6
t R,
4.4
4.2
ind
4.c
R/O Seq 115
3.E I I I
. 1 1’6 Seq 11
3.6
3.4
5
0
3.2
3.c
..
8
2.0 -
$
1.8 -
2 1
4 - \
1 2 l-6 -Step 1
2 3
4 1.4 -r
: 5
h t
43 _ 8 0 1.2 -Step 5 -
0 _ 5; \
w 5 ” ii 5 Z
EJ c _ 0 ?I 1.0 -
5
t
6 0.8 -r
7
7 7 0.6 - Step 5
i
9
s 0.5
8 z
GRAY SCALES
4
t%
c-9 TIME (GMT)
Figure 2.5-22: White Level Variation, Readout Sequences 115, 116, and 117
2.6 CONCLUSIONS
The photographic portion of Lunar Orbiter The location of Ranger VIII was photographed
Mission II is considered to be very nearly a successfully. The impact point has been identi-
complete success. All scheduled sites were fied by the NASA Lunar Orbiter photo data
photographed and 98.5% of the photography screening group as one of two small, bright
was reconstructed before readout was terminated craters. This location may be found near the
when the traveling-wave-tube amplifier (TWTA) center of Telephoto Frame 70, about 2.25 frame-
failed to turn on. let widths from the side opposite the edge data
and close to the junction of framelets 601 and
A few frames of Site HP-7 were affected by an 602.
unusual amount of lace defect in processing.
The attempt to obtain convergent stereo coverage
The specified resolution was achieved at all at Site IIS-B was successful, although readout
sites in both wide-angle and telephoto coverage. scanning characteristics introduce distortions
Fall-off of resolution was noted toward frame that degrade stereo quality. Side overlap at
edges as expected due to optical and photo- eight primary sites was sufficient to provide
metric factors, and in frames or portion of stereo coverage of some telephoto photographs.
frames where exposure level was near or be-
yond limiting values. In some localized areas The oblique coverage obtained at four secon-
surface topography resulted in more nearly dary sites photographed by single dualframes
grazing illumination that increased contrasts. is of excellent quality. Frame 162 of Site IIS-12,
In such instances, features smaller than system Copernicus, and Frame 213 of Site IIS-16,
specifications requirements can be detected. Marius, are particularly outstanding.
NASA-Langley, 1967 - 31
m-931 97
“The aeronautical and space activities of the United Slates shall be
conducled so a~ to contribute . . . to the expansion of human knowl-
edge of pbenomenb in the a/mosphere and space. The Administration
shall provide for the widest practicable and appropriate dissemination
of information concerning its activities and the resnh thereof.”
-NATIONAL AERONAUTICS AND SPACE ACT OF 1958