Professional Documents
Culture Documents
Document Title Page and Revision Record: PI-5781 FR Process Instruction Identification of Parts Other Than Castings
Document Title Page and Revision Record: PI-5781 FR Process Instruction Identification of Parts Other Than Castings
Document Title Page and Revision Record: PI-5781 FR Process Instruction Identification of Parts Other Than Castings
REVISION RECORD
REV. ITEM
LTR. ECR NO. DATE DESCRIPTION CHECKED APPROVED
1. PURPOSE
To specify markings on all parts other than castings produced worldwide.
2. LIMITATION
2.1 Identification requirements in this PI shall not include any “type” designations (TYPE 0, TYPE 1,
etc.). Requirements to be fully defined in this specification to avoid misalignment with engineering
drawings on future revisions of this PI.
2.2 Slant “A” is marked, style and proportion shall be per S9602.
2.3 Depressed letters such as stamped, rolled, etched, etc. are required unless otherwise specified. Mark
must be legible and adequate to survive normal life of the part. Raised material caused by marking,
beyond dimensional limits of part, must be approved by Garrett Engineering.
2.3.1 Ink stamp marking may be used but the mark must meet the following criteria.
The ink stamp must be of a size and clarity to be legible with unaided vision and must be
adequate to survive the normal life of the part. Exception as follows:
Stamped wheel shroud shall use “Ink stamps” or laser stamping. Steel stamping letters in a
sheet metal wheel shroud causes stress risers.
2.4 Manufacturer’s identification, if any, must be legible, and approved by Garrett. It also should be less
conspicuous than GARRETT identification.
2.5 OEM customer logo (Brand Mark), if applicable, must be on removable insert (which must be poke
yoked to ensure correct orientation) in the tooling.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Supplier DMX
Code Code
112931 01
126293 02
149424 03
122834 04
149282 05
Axial & Radial Location – Datamatrix should be center on top of Journal bearing face (one
side) per sketch shown below.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Depth: Marked symbols shall have less than 50μm depth. After marking parameters are set 2
pieces must be sectioned metallographically to confirm no cracks or raised surface visible
with 200X magnification.
Readability – Marked symbols must be verified with Keyence SR-2000 + Domo or
equivalent using a fixed mount camera designed for DPM/AIM. With reading grade “A” or
“B”.
Durability – DMX shall conform to readability requirement up to delivery at Garrett Plant.
Traceability – Suppliers must be able to present on demand by Garrett, the key characteristics
at the production date per quality requirements agreed with Garrett and the supplier.
3.4 Thrust Bearings NOT Permanently Attached
3.4.1 Slant “A” in a non-functional area.
3.4.2 Last four digits of part number, in a non-functional area.
3.5 Stamped Wheel Shrouds
3.5.1 Slant “A”.
3.5.2 Last four digits of part number, and dash number.
3.5.3 Letters shall be “Ink Stamped” or laser stamped.
3.6 Actuator Assemblies
3.6.1 Slant “A” (if applicable).
3.6.2 Part number and dash number.
3.6.3 Manufacturer’s Identification
3.6.4 See Section 3.23 for Actuator Assemblies requiring additional identification information
including DATAMATRIX identification. Character size recommendation (in millimeters):
NOTE: For Perkins OEM product portfolio only – No additional color markings (i.e. paint dots,
hand-written numbers/letters, etc.) are allowed on the outer surface, unless agreed with Garrett.
3.7 Other Stamped Parts such as Lock Plates, Clamps, Clamp Rings, etc.
3.7.1 Slant “A”.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.8.2.2 DMX on the curved surface (e.g. thrust collar) needs to be done at two places 180
degrees apart.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
When applicable, the following data fields shall be included in the database described in
Appendix A.
Field Name Applicability Description Format
Comp_Hsg_Assy_PN When compressor housing Part number of compressor NNNNNN-NNNN
is shipped as an assembly housing assembly
Foundry All cast housings Foundry name Alphanumeric, Variable
length, 25 characters max
Tool_Number All cast housings Tool number of Alphanumeric, Variable
length, 12 characters max
Cast_Date All cast housing Timestamp of casting Per ISO 8601
Material All cast housings Garrett IDM of casting IDM-1234
Leak_Test All cast housings Leak test result (units in Open
separate field)
KCC_NN_Desc When inspection is Key characteristic Numeric
mandatory inspection results (units in
separate field)
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.13.5 Effective September 16, 2016 (revision CJ of this PI), a traceable and unique Data matrix
symbol shall be laser engraved on turbine housing, per requirements in Appendix A and the
following size, format, and location. Ra requirement in Appendix A is not applicable.
Turbine Housing Data Matrix Size
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Datamatrix must be engraved on the Turbine housing E Datum machined surface (see green
area in the picture below).
When applicable, the following data fields shall be included in the database described in
Appendix A.
Field Name Applicability Description Format
Turb_Hsg_Assy_PN When turbine housing is Part number of turbine NNNNNN-NNNN
shipped as an assembly housing assembly
Foundry All cast housings Foundry name Alphanumeric, Variable
length, 25 characters max
Tool_Number All cast housings Tool number of Alphanumeric, Variable
length, 12 characters max
Cast_Date All cast housing Timestamp of casting Per ISO 8601
Material All cast housings Garrett IDM of casting IDM-1234
Leak_Test All cast housings Leak test result (units in Open
separate field)
KCC_N Any required inspection Key characteristic Numeric
inspection results (units in
separate field)
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Optionally for Wuxi Best only, fully machine compressor wheel data matrix encoded
data format (20 digits/letter):
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
When applicable, the following data fields shall also be included in the database described in
Appendix A.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.14.6 The following requirements apply to parts created prior to November 30, 2016 (before
revision CM of this PI). See 3.14.5 for requirements effective November 30, 2016 (revision
CM of this PI).
The Garrett part number is to be Ink Stamped on the Backface including the date the wheel
was balanced. Both must be human readable. The part number is to include the last four digits
of the part and the dash number. Example: 735657-0011 to read 5657-11. Date to be read
as dd mmm yyyy (09 JAN 2015) or dd mmm yy (09 JAN 15).
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.18.4 Effective September 16, 2016 (revision CJ of this PI), a traceable and unique Data matrix
symbol is required to be laser engraved on each center housing, following the requirements in
Appendix A and the following size, format, and location. Ra requirement in Appendix A is
not applicable.
Center Housing Data Matrix Size
Data Matrix Configuration Data Element Symbol Size Symbol Size with
per ECC200 Capacity Size Quiet Zone
8x32 elements 20 Numeric 0.25mm 2mm x 8mm 3mm x 9mm
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Datamatrix must be engraved on oil outlet flange surface out of the sealing area per product
line specifications (see green zone in the picture below). Oil outlet flange must be designed to
accept symbol with quiet zone specifications per table above and in approximate location
shown in picture below.
When applicable, the following data fields shall also be included in the database described in
Appendix A.
Field Name Applicability Description Format
Ctr_Hsg_Assy_PN When center housing is Part number of center NNNNNN-NNNN
shipped as an assembly housing assembly
Foundry All cast housings Foundry name Alphanumeric, Variable
length, 25 characters max
Tool_Number All cast housings Tool number of Alphanumeric, Variable
length, 12 characters max
Cast_Date All cast housing Timestamp of casting Per ISO 8601
Material All cast housings Garrett IDM of casting IDM-1234
Leak_Test All cast housings Leak test results, separate Open
for oil and water circuits
(units in separate field)
Line_Number
Critical Assembly Central Housing with Torque value, angle value Units and status
Characteristics* washer and water plug (if applicable), and
presence of the washer
KCC_N Any required inspection Key characteristic Numeric
inspection results (units in
separate field)
* Mandatory for projects sourced after May 1st 2020 and a strong recommendation for projects sourced and ongoing
prior to 1st of May 2020.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.22 Crank Assembly with Double Pins (Internal and External Pin Cranks) & Wastegate Actuator
Plates
One or two letters per family P/N as defined by Table 2 and dash number.
Example: F15 for 717507-15
Unless specified on the Engineering Drawing, the identification marking location is on the pin crank
external side.
NOTE: For Perkins OEM product portfolio only – No additional color markings (i.e. paint dots, hand-
written numbers/letters, etc.) are allowed on the outer surface, unless agreed with Garrett.
3.23 Turbine Nozzles (Fixed) Machined and Nozzled Shrouds Machined
The following ink stamp identification markings are required. All markings should be located on
the flow side of the nozzle of the finished part. Letter height of all markings should be 6 to 8 mm
containing all capital letters.
A. Machined Part Number
B. Casting flow identification as indicated on drawing (Example; 100% Flow)
C. Date identification
3.24 Actuator, VNT Cartridges Assemblies and Flange Identified with Datamatrix Code
3.24.1 Actuator Assemblies
3.24.1.1 Pneumatic Actuator Assemblies
The required information inside the DATAMATRIX Code is the following:
1. Customer part number and dash number
2. Assembly line number
3. Production date
4. Production time
5. Diaphragm lot control number
6. Position sensor production batch number
7. Production shift number
8. Sensor linearity value
The DATAMATRIX Code must comply with requirements in Appendix A,
including database of traceable data.
NOTE: For Perkins OEM product portfolio only – No additional color
markings (i.e. paint dots, hand-written numbers/letters, etc.) are allowed on the
outer surface, unless agreed with Garrett.
The format for the information must be defined during development of the
pneumatic actuator assembly (see example below).
Part number Line N° Date Hour Batch Batch Equipment Linearity
diaphragm sensor N°
7796570002 X34029 08064 080000 A1 07125A A 0200
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
String Example:
7796570002X3402908064080000A107125AA0200
3.24.1.2 Simple Electric Actuator (Commercial Vehicles)
The required information inside the DATAMATRIX Code is the following:
1. Garrett part number
2. Supplier part number
3. Unique serial number
4. Date of manufacture
5. Actuator Supplier Code
6. Communication type
The DATAMATRIX Code must comply with requirements in Appendix A,
including database of traceable data.
NOTE: For Perkins OEM product portfolio only – No additional color
markings (i.e. paint dots, hand-written numbers/letters, etc.) are allowed on the
outer surface, unless agreed with Garrett.
The format for the information must be defined during development of the
pneumatic actuator assembly (see example below).
Unique Actuator’s
Garrett Part Supplier part Date of Communication
serial supplier short
number number manufacture type
number Code
8457670010 0000408087 17D280193 18365 01 ANA
10 number 10 characters 9 characters 5 number 2 characters 3 characters
characters characters
Julian date
Year (2 characters)
Day (3 characters)
Total number of characters: 39
String example:
8457670010000040808717D2801931836501ANA
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.24.2 VNT Cartridges Assemblies: Required Information inside Datamatrix Code is as follows.
1. 5 last numbers of cartridge part number
2. Dash number
3. Supplier code
4. Day/Month/Year of production
5. Assembly line number
6. Daily production serial number
Data matrix must comply with requirements in Appendix A, including database of traceable
data. The encoded content should follow the structure below.
8739008C061110A2534
SAP Vendor DATAMATRIX
Code supplier short Code
100705 A
125346 B
130228 C
146964 D
100482 E
123462 F
125521 G
149424 H
123361 I
149498 J
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.24.3 Flange (GTC & GTD types): Required Information inside Datamatrix Code is as follows
1. Part number
2. Dash number
3. Supplier code
4. Day/Month/Year of production
Data matrix must comply with requirements in Appendix A, including database of traceable
data. The encoded content should follow the structure below.
78829901E080211
The flange’s Datamatrix supplier code corresponds to the vendor code in the table below.
SAP Vendor DATAMATRIX
Code supplier short Code
100642 A
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Incorrect
ink traces
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
811185
815595
831614
The supplier identification is made with a combination of grooves machined on inner
diameter that do not interact with any functional areas. The groove locations are set at
1mm from the pin locating hole ends on the compressor and 1 & 2 mm for the turbine side
per print identification.
The groove is defined by: width 0.25-0.35mm and depth 0.20 mm ended with a radius.
No burrs are allowed at any junction of these grooves and other machining details inside
of the bearing.
Identification must be visible from the pin locating hole or thru the bearing inner diameter.
Any doubts on this identification must be noted in the APQP documentation and agreed
between Garrett and the relevant suppliers.
Supplier’s identification is made per following table combination.
149424 No No No
149282 No No Yes
122834 No Yes No
126079 Yes No No
Yes Yes No
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
T2
C1 T1
3.28.2 Z Bearing Identification with Traceability per Serial Number or Data matrix
Effective November 30, 2016 (revision CM of this PI), a data matrix symbol is required to
be laser marked on the indicated side of the bearing per requirements of Appendix A, and
the following size, format and location.
Z-Bearing Data Matrix Size
Data Matrix Data Element Size Symbol Size Symbol Size
Configuration Capacity with Quiet
per ECC200 Zone
16x16 24 Numeric 0.1875mm 3mm square 4mm square
elements
Z-Bearing Data Matrix Encoded Data Format
Base P/N Dash Supplier Julian date Daily serial number Line / Machine
short code
Day Year
6 digits 2 digits 2 digits 3 digits 2 digits 5 digits 2 digits
836323 02 02 343 16 12345 02
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
The encoded content must use the exact number of digits and order of data.
Orientation must be within ± 2° Vs perpendicular axis of pin locating. Balanced against
pin locating axis, with location detail in appendix with +/- 0.50 mm axial location
tolerances.
Height – Marks shall not exceed 15µm height increase or Rp 15µm
Traceability – Suppliers must be able to present on demand by Garrett the key
characteristics at the production date per quality requirements agreed with Garrett and the
supplier.
Data matrix supplier code corresponds with the vendor code in given in the table below.
Z-Bearing Vendor Short Codes for Data Matrix
DMX short-
Supplier Code
code
149424 01
149282 02
122834 03
126293 04
126079 05
111659 06
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
For symmetric bearing (Z6 or Z7) For Asymmetric bearing (Z6 or Z7)
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.29.2 Shaft with Traceability Requested per Serial Number or Data matrix
A data matrix symbol is required to be laser marked on the slender of the shaft compliant
with requirements of Appendix A, and the following size, format and location.
Shaft Data Matrix Size
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
The encoded content must use the exact number of digits and order of data.
Marks shall not exceed Rz 15µm.
Suppliers must be able to present on demand by Garrett the key characteristics at the
production date per quality requirements agreed with Garrett and the supplier.
Locate data matrix as shown below:
a) Z bearings DMX position per bearing diameter sizes
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Supplier Codes
Data matrix supplier code corresponds to manufacturing plant of the shaft associated with
SAP vendor code. For vendors with multiple plants see appropriate plant code.
Shaft Vendor Codes for Data Matrix
Vendor Vendor Code
118704 See Plant #01
147628 See Plant #01 Plant Location Vendor Code
121642 See Plant #01 JPN 00
121895 See Plant #01 CHN 02
125408 03 SLO 01
117799 04 Plant code #01 to be used only for
121964 04 SAP: 118704, 147628, 121642, &
100482 05 121895
130767 11
126079 12
148874 13
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.30 Backplate & Seal Plate Data Matrix Code Identification with Traceability
A Data matrix following requirements of Appendix A, and the following size, format, and location
shall be laser marked on the plate.
Seal plate & Backplate Data Matrix Size
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Seal plate & Backplate Vendor Short Codes for Data Matrix
SAP Vendor Data matrix
Code Supplier short Code
137886 01
100530 02
113280 03
122406 04
115513 05
141985 06
144332 07
121550 08
100674 09
122701 10
141985 11
141985 12
147765 13
130228 14
149282 15
130408 16
126079 17
126273 18
112659 19
123364 20
122711 21
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
The data matrix must be engraved on area located under compressor wheel per the picture below.
NOTE: Backplate designs that cannot meet the location shown below are to be specified on the
Drawing.
When applicable, the following data fields shall also be included in the database described in
Appendix A.
Field Name Applicability Description Format
Foundry All cast plates Foundry name Alphanumeric, Variable
length, 25 characters max
Tool_Number All cast plates Tool number of Alphanumeric, Variable
length, 12 characters max
Cast_Date All cast plates Timestamp of casting Per ISO 8601
Material_Batch Batch ID of material Alphanumeric, Variable
length, 12 characters max
Machining_Line Machining line ID Alphanumeric, Variable
length, 12 characters max
KCC_N Any required inspection Key characteristic Numeric
inspection results (units in
separate field)
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
839497 -20 XX
Data matrix Size & Location – The marking zone is a square shape, location is defined per the
noise suppressor print. Recommended area is:
• Marking area 10X10 mm, Quiet zone 11X11 mm
In addition to the datamatrix, a human readable Part Number should be printed. See the figure
below.
Readability – Marked symbols must be verified with Cognex Dataman 8500, Keyence MD-XAD1
or equivalent using a fixed mount camera designed for DPM (direct part marking) with a minimum
reading grade “B”.
Durability – Symbol shall conform to readability requirement up to delivery at the Garrett Plant.
Depth - Marks shall not exceed 15μm depth.
Traceability – Suppliers shall create a traceability database with 1 entry per component including to
the following data:
• Serial Number
• Noise suppressor Part number
• Manufacturing Date
• Batch Number
NOTE: For Perkins OEM product portfolio only – No additional color markings (i.e. paint dots,
hand-written numbers/letters, etc.) are allowed on the outer surface, unless agreed with Garrett.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
• Marking area 7X7 mm, Quiet zone 8X8 mm, for PN 773492-0002
DMX
location
In addition to the Datamatrix, a human readable Part Number should be printed. See the figure below -
location and appearance.
Readability – Marked symbols must be verified with Cognex Dataman 8500, Keyence MD-XAD1
or equivalent using a fixed mount camera designed for DPM (direct part marking) with a minimum
reading grade “B”.
Durability – Symbol shall conform to readability requirement up to delivery at the Garrett Plant.
Depth - Marks shall not exceed 15μm depth.
Traceability – Suppliers shall create a traceability database with 1 entry per component including to
the following data:
• Serial Number
• Heat Shroud Part number
• Manufacturing Date
• Batch Number
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
b) Content
Supplier Serial
P/N Dash Julian Date BEP
Code number
Day Year 3 digits (space
6 digits 2 digits 2 digits 5 digits
3 digits 2 digits + 2 digits)
846433 01 02 343 16 12345 _43
Supplier DMX
Code Code
119609 01
148587 02
146724 03
151654 04
2. A 2-digit Human readable number, representing the Bench Axial Endplay of the Bearing
Cartridge in microns, is to be added adjacent to the data matrix. See below for location
options, subject to available space on marking surface.
3. Height – Marks shall not exceed 15μm height increase or Rp 15μm, UNLESS Specified in
Drawing.
4. Readability – Marked symbols must be verified with Cognex Dataman 8500, Keyence MD-
XAD1 or equivalent using a fixed mount camera designed for DPM/AIM.
5. Durability – DMX shall conform to readability requirement up to delivery at Garrett Plant.
6. Traceability – Suppliers must be able to present on demand by Garrett, the key
characteristics at the production date per quality requirements agreed with Garrett and the
supplier.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
7. Orientation – Markings for data matrix and 2-digit human readable number must be
oriented in same direction relative to datum system shown in drawing (see figure above).
The following human readable markings to be added on the same surface as the Garrett data
matrix, with location subject to available space. Supplier to determine marking specifications,
while adhering to height (note 3) and orientation (note 7) requirements above.
Marking Type Comments
Garrett Part Number 6-digit part number + 2-digit dash number
Supplier Part Number Determined by supplier
Serial Number 10 digits (Julian Date + Serial Number)
Optional: Supplier data matrix (if available) to be added below human readable markings. See
the figure below for an example.
GARRETT PART NUMBER
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.36 Pedestal
Effective from revision DT of this PI, a traceable and unique Data matrix symbol shall be laser
engraved on the Pedestal, per requirements in Appendix A and the following size, format, and
location. The Ra requirement in Appendix A is not applicable.
Pedestal Data Matrix Size
The encoded content must use the exact number of digits and order of data.
Engraving marks amplitude shall not exceed 50 μm or Rz ≤ 50 μm.
Datamatrix supplier code corresponds with the vendor code in given in the table below.
Pedestal Vendor Short Codes for Data Matrix
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
When applicable, the following data fields shall be included in the database described in Appendix
A.
Field Name Applicability Description Format
Pedestal_Assy_PN When Pedestal is shipped Part number of Pedestal NNNNNN-NNNN
as an assembly housing assembly
Foundry All cast housings Foundry name Alphanumeric,
Variable length, 25
characters max
Tool_Number All cast housings Tool number of Alphanumeric,
Variable length, 12
characters max
Cast_Date All cast housing Timestamp of casting Per ISO 8601
Material All cast housings Garrett IDM of casting IDM-1234
Leak_Test All cast housings Leak test result (units in Open
separate field)
KCC_N Any required inspection Key characteristic Numeric
inspection results (units
in separate field)
3.37 Insert
This section is applicable for Inserts that require a data matrix per engineering drawing. A data
matrix shall be laser marked on the Insert OD perimeter area of each insert as highlighted in the
picture below.
Height of individual character must not exceed 3.18mm/0.125in and depth must not exceed
0.38mm/0.015in. Markings and locations are to be identified on the ISIR (Initial Sample Inspection
Report) or a subsequent inspection report for approval by the Garrett Business Center responsible
for the product.
Machine shop identification required if it is not Garrett machine shop.
Identification markings are to be human readable. Depth of the marks may not exceed
0.51mm/0.020in. Marks must be of a size and clarity to be legible with unaided vision.
Unless specified on the engineering drawing, machine shop identifier location on as cast outside flat
surface near oil outlet flange or on the side of the casting.
A traceable and unique Data matrix symbol is required to be laser engraved on each center housing,
following the requirements in Appendix A and the following size, format, and location.
Insert Data Matrix Size
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
The encoded content must use the exact number of digits and order of data.
Engraving marks amplitude shall not exceed 50 μm or Rz ≤ 50 μm.
Datamatrix supplier code corresponds with the vendor code given in the table below.
SAP Vendor Code Datamatrix supplier
short code
137666 01
140090 02
146605 03
130749 04
110217 05
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.38.1 Duplicate symbols may be required on some components. In case of duplicate symbols
on one component, the same information shall be encoded in each symbol.
3.38.2 Components serialized with data matrix shall maintain a database of information at the
marking location. The database shall meet the requirements given in Appendix A for
format, content, and transmission of data.
3.38.3 A light back-pass field shall be used behind the symbol and in the quiet zone, with dark
elements used for the symbol itself.
3.38.4 When engineering drawing requires data matrix, each component produced shall be
serialize with unique number encoded in a data matrix.
3.38.5 Serial numbers shall not be duplicated within 3 years. Marking stations shall have
systems to ensure serial numbers are not re-used. If components are scrapped after
serialization, the serial number of the scrapped part shall not be re-used within 3 years. If
a part is re-worked to bring it into compliance, the serial number shall not change.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
SAP codes are for reference only – in case of conflict use code on purchase agreement.
Table 3.38B: E-Turbo Rotor Spacer Bearing Side Part Number Code
Spacer Bearing Side Part Number Associate Code for DMX
884847-0003 1
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
4.5 mm Square 16x16 cell data matrix at the center of the magnet width with the position tolerance < 0.2
mm. In case of data matrix rework, existing data matrix mark will be erased first before printing new data
matrix exactly opposite side of the first data matrix on the same plane.
Table 3.38C: E-Turbo Rotor Magnet Short Code
Supplier Name Supplier Short code SAP / SCC Vendor Code
SDM 01 151357
SAP codes are for reference only – in case of conflict use code on purchase agreement.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.6 mm Square 16x16 cell data matrix at the center of the sleeve length with the position tolerance < 0.2
mm. In case of data matrix rework, existing data matrix mark will be erased first before printing new data
matrix exactly opposite side of the first data matrix.
SAP codes are for reference only – in case of conflict use code on purchase agreement.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
4.7 mm Square 16x16 cell data matrix on the outer diameter with the position tolerance < 0.2 mm. In
case of data matrix rework, existing data matrix mark will be erased first before printing new data
matrix exactly opposite side of the first data matrix.
Table 3.38E: E-Turbo Rotor Sleeve Short Code Table
Supplier Name Supplier Short code SAP / SCC Vendor Code
Heben 01 140031
SAP codes are for reference only – in case of conflict use code on purchase agreement.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
2.5 mm x 8.5 mm Rectangle 8x32 cell data matrix with the position tolerance < 0.2 mm. In case of data
matrix rework, existing data matrix mark will be erased first before printing new data matrix exactly
opposite side of the first data matrix.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
SAP codes are for reference only – in case of conflict use code on purchase agreement.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
5 mm x 5 mm Rectangle 18x18 cell data matrix with the position tolerance < 0.2 mm. In case of data
matrix rework, existing data matrix mark will be erased first before printing new data matrix exactly
opposite side of the first data matrix.
SAP codes are for reference only – in case of conflict use code on purchase agreement.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
3.39.1 Duplicate symbols may be required on some components. In case of duplicate symbols
on one component, the same information shall be encoded in each symbol.
3.39.2 Components serialized with data matrix shall maintain a database of information at the
marking location. The database shall meet the requirements given in Appendix A for
format, content, and transmission of data.
3.39.3 A light back-pass field shall be used behind the symbol and in the quiet zone, with dark
elements used for the symbol itself.
3.39.4 When engineering drawing requires data matrix, each component produced shall be
serialize with unique number encoded in a data matrix.
3.39.5 Serial numbers shall not be duplicated within 3 years. Marking stations shall have
systems to ensure serial numbers are not re-used. If components are scrapped after
serialization, the serial number of the scrapped part shall not be re-used within 3 years. If
a part is re-worked to bring it into compliance, the serial number shall not change.
3.39.6 Depth
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Marked symbols shall have less than 50μm depth. After marking parameters are set 2
pieces must be sectioned metallographically to confirm no cracks or raised surface visible
with 200X magnification.
3.39.7 FCC- Rotor Assembly
Applicability: A data matrix symbol is required to be laser marked on the outer diameter
of the sleeve surface compliant with ISO 29158 requirements and the following size,
format and location.
Grade Requirement: DPM 2.0/5-20/660/(45Q|90), Grade C or better is required for
each symbol.
Data Matrix Size
Data Matrix Qty Data MIN MIN Symbol MIN Symbol
configuration per Capacity Element Size Size with Quiet
ECC200 Size Zone
16 x 16 elements 1 23 Numeric 0.25 mm 4 mm x 4 mm 4.5 mm x 4.5 mm
Element size may be increased when larger inscribed slender available on spacer bearing.
Data Matrix Encoded Data Format
The encoded content must use the exact number of digits and order of data.
Supplier Short Batch Base Part Dash Part Serial
Timestamp
Code (Table 1) Number Number Number Number
2 numeric 5 numeric digit - DDDYY 4 numeric 6 numeric 2 numeric 4 numeric
digits Day - 3 digits Year - 2 digit digits digits digits digits
01 028 19 1122 123456 01 1234
* YY – Year, DDD – Julian date
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
LP Side HP Side
BALANCE PLANE 1 BALANCE PLANE 2
5 ± 0.5 mm
4.5 mm Square 16x16 cell data matrix 5 mm away from sleeve end with a position tolerance ± 0.5 mm. In
case of data matrix rework, existing data matrix mark will be erased first before printing new data matrix
and should be at 90°in clockwise direction to the first data matrix.
Table 3.39A: FCC Rotor Assembly Short Code Table
Supplier Name Supplier Short code SAP / SCC Vendor Code
ITG 01 104205
SAP codes are for reference only – in case of conflict use code on purchase agreement.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Excell Tool 00
Tricast 01 or
IDA 02 or IDA
LBQ Foundry 03
(formerly Xolox)
Consolidated
06 or
Cross 07
Gregg Industries 09
Sonora Manufacturing 10
Dial Precision 12
Burlington 13
AlliedSignal 14
Lancast Aluminum 19
Alard Machine 21
Berlin Foundry 23
Skypower 24
Cogeme – Romania 25
Neil 26
Machen 27
Free-Gate 28
Hinderliter 29
Wiza 36 or
Alloy Die 38
Holloy Art 40
Interface 41
ENKEI 42 or EC or
Fujiwa 43 or FJW
New Wei San 44 or NWS
QiShuYan 45 or QSY
Jiang Yin 46 or JT or
Chapman W.L. 50
Aikoku 51
Wuxi Yongxing Machinery Co. Ltd 52
BIAM (Baimtec Material Co. Ltd.) 53
Gitts 55
Grede Foundry 60
Fab Sheet 61
Garrett Waterford 62
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
TABLE 1 (continued)
Garrett Presov 63
PRAE 64
Ross 65
LapRoss 66
Furukawa 67
S&H 68
TurboCAM 69
High Tech 70
Orange Count 71
Torrance 72
Baja Pacific 73
Best 74
Acro Broach 75
Bradley 77
Baja Oriente 80
C & L Weld 81
Reliable Casting 84
Eberle 88
Basso & Yabuki 89
Strite 90 or S
Dial Precision 91 or D
Helios 92 or H
Anodyne, Inc 93
MQS Inspecti 96
Invar 98 or
Top Die 99
LOC Performance
Products
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Table 2: Crank Assembly, Rod, Wastegate Actuator Plate, & Heat Shield Identification
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Table 2: Crank Assembly, Rod, Wastegate Actuator Plate, & Heat Shield Identification (Con’t)
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Table 2: Crank Assembly, Rod, Wastegate Actuator Plate, & Heat Shield Identification (Con’t)
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Figure 2
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Unless otherwise specified, the size of elements in the data matrix shall comply with the following
table. Larger element size is preferred when space is available.
Surface Roughness Laser Marking Ink Jet Marking
Requirement (Ra, µm)
Minimum Element Minimum Element
Size (mm) Size (mm)
1.6 0.19 0.40
3.2 0.25 0.60
6.4 0.40 0.80
Laser marked parts shall use a back-pass larger than the symbol by at least 1 element width, preferably
2 elements wide. The back pass will reduce glare on reflective surfaces, improve surface finish, and
improve contrast. The backpass shall be light and the symbol elements dark.
Duplicate marks may be required on some components. In case of duplicate marks on one component,
the same information shall be encoded in each mark.
Encoded content shall conform to the format specified by component type. Industry standards for
encoded headers, footers, field separators, and data identifiers (such as GS1 or MH10) shall not be used
unless explicitly requested.
A.2 Traceable Database
Components serialized with data matrix shall maintain a database of information. In addition to data
encoded in the data matrix, a database with component attribute data shall be maintained at the site of
the marking equipment.
Garrett reserves the right to collect information from the database through mutually agreed protocol.
The database should be a multi-threaded database (such as MySQL or MS Access) installed on a
Windows PC.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
When applicable, the following data fields shall also be included in the database. Additional
data fields may be required by component type.
Field Name Applicability Description Format
Material Components with material Garrett IDM IDM-1234
designated on Garrett
drawing
Batch_Code Parts produced in lots or Supplier defined lot or Alphanumeric, Variable
batches, including castings batch code length, 25 characters max
Additional data should be added when available. This includes test results (pass/fail),
inspection results (dimensional data), etc. Explanation of additional data fields shall be
included in the data dictionary.
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Data field names and field values shall use only the following ASCII characters. The semi-
colon (;) and comma (,) are reserved for field delimitation. No spaces shall be used in field
names. The period (.) shall be used to identify a decimal point.
Decimal Description
Codeword
43 + Plus sign
45 - Dash
46 . Period
47 / Forward slash
48-57 0-9, Numerals
58 : Colon
65-90 A-Z, Uppercase Alpha Characters
95 _ Underscore
97-122 a-z, Lowercase Alpha Characters
Qualitative test result data shall follow the following field values:
Field Value Meaning
PASS Test cycle completed and part is good (Avoid Accept, 1, Y, good)
FAIL Test cycle completed and part is not good (Avoid Reject, 0, bad, NG)
ERROR Test cycle did not complete or part status cannot be determined (Avoid null, -1, 2, N/A)
Dimensional data shall use SI system of units per ISO 80000-1. The units shall be defined in
an adjacent field (example below).
Diameter_Hex01 Diameter_Hex01_units
20.01 mm
20.00 mm
19.98 mm
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential
Leap years:
(2000, 2004, 2008, 2012, 2016, 2020...)
Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec
1 1 32 61 92 122 153 183 214 245 275 306 336
2 2 33 62 93 123 154 184 215 246 276 307 337
3 3 34 63 94 124 155 185 216 247 277 308 338
4 4 35 64 95 125 156 186 217 248 278 309 339
5 5 36 65 96 126 157 187 218 249 279 310 340
6 6 37 66 97 127 158 188 219 250 280 311 341
7 7 38 67 98 128 159 189 220 251 281 312 342
8 8 39 68 99 129 160 190 221 252 282 313 343
9 9 40 69 100 130 161 191 222 253 283 314 344
10 10 41 70 101 131 162 192 223 254 284 315 345
11 11 42 71 102 132 163 193 224 255 285 316 346
12 12 43 72 103 133 164 194 225 256 286 317 347
13 13 44 73 104 134 165 195 226 257 287 318 348
14 14 45 74 105 135 166 196 227 258 288 319 349
15 15 46 75 106 136 167 197 228 259 289 320 350
16 16 47 76 107 137 168 198 229 260 290 321 351
17 17 48 77 108 138 169 199 230 261 291 322 352
18 18 49 78 109 139 170 200 231 262 292 323 353
19 19 50 79 110 140 171 201 232 263 293 324 354
20 20 51 80 111 141 172 202 233 264 294 325 355
21 21 52 81 112 142 173 203 234 265 295 326 356
22 22 53 82 113 143 174 204 235 266 296 327 357
23 23 54 83 114 144 175 205 236 267 297 328 358
24 24 55 84 115 145 176 206 237 268 298 329 359
25 25 56 85 116 146 177 207 238 269 299 330 360
26 26 57 86 117 147 178 208 239 270 300 331 361
27 27 58 87 118 148 179 209 240 271 301 332 362
28 28 59 88 119 149 180 210 241 272 302 333 363
29 29 60 89 120 150 181 211 242 273 303 334 364
30 30 90 121 151 182 212 243 274 304 335 365
31 31 91 152 213 244 305 366
GAR_DOC (R. 10/18) The user must verify that this is the current revision prior to use and if not, remove it from use. Garrett Proprietary & Confidential