Professional Documents
Culture Documents
A32 UL Instruction Manual
A32 UL Instruction Manual
Usage
UL1066 , ANSIManual
C37.13 and CSA C22.2 NO.31
User Manual
ZA32202209UL
Installation manual
Overview 01
Selection Guide 02
Product parameters 06
Environmental Conditions 07
Pckage identification 08
Storage 09
Necessary tools 10
Unpacking 11
Handling 13
Installation Dimension 16
Terminal Adjustment 36
ELM10 41
Accesories 44
Main Menus 61
Menu 62
Overview of Functions 65
Appendix 66
Overview
This device should be installed, operated, serviced and maintained only by professional personnel.
Noark Electric is not responsible for any consequences caused by non-compliance with this the manual.
After unpacking the product, check for any damage and the integrity of other items.
Do not install the product in inflammable, explosive, humid and condensing environment.
1
Do not install the product at places where gas medium can cause metal corrosion and insulation damage. 2
Connect the product to the proper power supply and standard wires.
Leave sufficient space and safe distance around the product.
3
Do not touch the conductive parts during operation.
4
Disconnect all the power sources during installation and maintenance.
5
Failure to follow the above instructions may result in equipment damage, personal injury or even death.
6
Environmental protection
To protect environment, this product and its components should be disposed properly as industrial waste upon
end of life; or delivered to recycling plant who will dismantle and recycle the product according to relevant
national regulations.
5. Nameplate b) closing ON
User Manual 01
Selection Guide Selection Guide
XF 12 N A
I CAS: Cassette
Frame size I II III IV
II
12: 3200A
III N: UL
I XF: Shunt close
Pole
IV 3: 3P II 12: For 3200A PCB
4: 4P III N: UL
H: Horizontal Control voltage
IV
V V: Vertical A: 24-30VDC, B: 48-60VDC, C: 110-130VAC/DC, D: 208-240VAC/DC
* 3200A only available with vertical wiring.
Rated current
1600: 800A, 1600A,
VI
2500: 2000A, 2500A, Catalog Designation for Under voltage Trip
3200: 3200A
UVT 12 N A
I II III IV
Catalog Designation for Trip unit
I UVT: Under voltage trip
II 12: For 3200A PCB
SU 30 N H A III N: UL
I II III IV V Control voltage
IV
A: 24VDC, B: 48VDC, C: 110 - 130VAC/DC, D: 208 - 240VAC/DC E: 380-415VAC
I SU: Smart unit
Protection type
II
20: LI, 30: LSI, 40: LSIG
III N: UL
Measurement type
Catalog Designation for Motor Operator Device
M: Basic without measurement (LED display)
IV
A: Ammeter (LCD display)
MD 12 N C
H: Harmonics (LCD display)
Control voltage I II III IV
V
A: 24VDC,C: 110-130VAC, D: 208-240VAC
I MD: Motor operator Device
II 12: For 3200A PCB
III N: UL
Control voltage
IV
A: 24-30VDC, B: 48-60VDC, C: 110-130VAC/DC, D: 208-240VAC/DC
Catalog Designation for Position indicator Catalog Designation for Pushbutton lock device
EF 12 N VBP 12 N
I II III I II III
Catalog Designation for Doorframes for fixed type Catalog Designation for Door interlocks for withdrawable type
CDP 12 N VPEC 12 N S
I II III I II III IV
I CDP: Doorframes for fixed type I VPEC: Door interlocks for withdrawable type
II 12: For 3200A PCB II 12: For 3200A PCB
III N: UL III N: UL
P: Position interlock
IV
S: Status interlock
Catalog Designation for Doorframes for withdrawable type
NCT 12 N
I DDP: Doorframes for withdrawable type
Ⅰ Ⅱ Ⅲ
II 12: For 3200A PCB
III N: UL Ⅰ NCT: External Current transformer for Neutral
Ⅱ 12: For 3200A PCB
Catalog Designation for Phase barrier for fixed type Ⅲ N: UL
PHS 12 N 2
I II III IV Catalog Designation for Energy-Limiting Maintenance Switch (ELM Switch)
Catalog Designation for Phase barrier for withdrawable type Catalog Designation for Lockable switch cover for ELM Switch
DPS 12 N 2 LSC 10
I II III IV Ⅰ Ⅱ
I DPS: Phase barrier for withdrawable type Ⅰ LSC: Lockable switch cover for ELM Switch
II 12: For 3200A PCB Ⅱ 10: For UL PCB
III N: UL
2: 2 pcs for 3P Note: LSC10 is an optional unit, please comment if it is required when purchasing.
IV
3: 3 pcs for 4P
Ambient temperature
Type A32Q A32R A32H ASD32Q ASD32R ASD32H
A32 Circuit breakers can operate in the following environmental conditions:
Pole 3P/4P 3P/4P
With M Smart Unit: -40℃ ~ 70℃;
Installation Fixed/Withdrawable Fixed/Withdrawable
With H Smart Unit: -20℃ ~ 70℃;
Fixed:800/1600/2000/2500
Rated current(A) 800/1600/2000/2500/3200
Withdrawable:800/1600/2000/2500/3200
A32 Circuit breakers can operate at higher temperatures than the reference temperature 40℃,in this case,the derating coefficients
Rated Maximum Valatge(V) 254/508/635 254/508/635 shown in the table must be applied.
Frequency(Hz) 50/60 50/60 Rated Temperature(℃ )
254V 65 85 100 / / / Current(A) <40 45 50 55 60 65 70
Interrupting rating at rated maximum voltage (kA) 508V 65 85 100 / / /
800 100% 100% 100% 100% 100% 100% 100%
635V 65 85 100 / / /
254V 65 85 100 65 85 100 1600 100% 100% 100% 100% 100% 100% 100%
Short time withstand current (kA) 508V 65 85 100 65 85 100 2000 100% 100% 100% 100% 100% 100% 93%
635V 65 85 100 65 85 100 2500 100% 95% 92% 88% 83% 80% 75%
open <70 <70
operating time(ms) 3200 100% 95% 92% 88% 83% 80% 75%
close <40 <40
without maintenance 10000 10000 10000 10000 10000 10000
mechanical
life cycle(time)
with maintenance / / / / / / Altitude
without maintenance 6000 6000 6000 6000 6000 6000
electrical
with maintenance / / / / / / A32 Circuit breakers do not undergo changes in rated performance up to 2000m.Beyond this altitude ,the derating coefficients shown in
21.65×23.62×18.11 21.65×23.62×18.11
the table must be applied.
(550×520×460) (550×520×460)
3P
Ventilation Area Top: 9092mm² Ventilation Area Top: 9092mm² Altitude(m)
Bottom:9092mm² Bottom: 9092mm² <2000 2600 3900 4900
withdrawable
21.65×25×18.11 21.65×25×18.11 Rated Voltage(V) 1xUe 0.95xUe 0.8xUe 0.7xUe
Enclosure dimension (550×635×460) (550×635×460)
4P Rated Current(A) 1xIn 0.99xIn 0.96xIn 0.94xIn
H×W×D(in/mm) Ventilation Area Top: 11963mm² Ventilation Area Top: 11963mm²
Bottom: 11963mm² Bottom: 11963mm²
21.65×20.47×14.17 21.65×20.47×14.17 Humidity
3P
(550×520×360) (550×520×360)
fixed The relative humidity does not exceed 85% at 40℃,the monthly average maximum of relative humidity in the wettest month does not
21.65×25×14.17 21.65×25×14.17
4P
(550×635×360) (550×635×360) exceed 90%.
The effect of surface condensation caused by temperature changes on product performance should be taken into consideration.
Withdrawable 800 80
Vertical Horizontal
In
Qty Size(in) Size(mm) Qty Size(in) Size(mm)
Note: These tables should be used as a general guideline only, the solution used should take into consideration the varieties of switchgear types and conditions.
1 1
UL 1066/ANS 1
CSA C22. File E502732
No.3
CSA C22.2
4 5 6 7 9 8
7 8 9 1 2 3
1 2 3 4 5 6
5 6 7 9 td
3 4Co.,L
8
8 9 1 2 i)
4 5 6 7ngha
trics 1 2 3 (sha
NOARK Elec i) Co.,Ltd
trics (shangha
NOARK Elec
1PCS
1PCS
A32
A32 Power
PowerCircuit
CircuitBreaker
Breaker
A32H3DV3200
A32H3DV3200
+AX12ND66
+AX12ND66
+UVT12NA
+UVT12NA
+XF12NA
+XF12NA
+SHT12NA
+SHT12NA
+MD12NA
+MD12NA
+SU30NHA
+SU30NHA
Conform standard:
Conform
UL standard:
1066/ANSI C37.13
CSA C22.2 No.31C37.13
UL 1066/ANSI
CSA C22.2 No.31 File E502732
File E502732
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 9 8
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 9 8
NOARK Electrics (shanghai) Co.,Ltd
NOARK Electrics (shanghai) Co.,Ltd
in/mm
17
0.67(17)
LOW VOLTAGE AC POWER CIRCUIT BREAKER
UL 1066/ANSI C37.13/CSA C22.2 No.31
Frame Size:3200A Frequency:50/60Hz
Rated Continuous Current: Poles:
Cat.
MFG.Date:
Serial No. :
E510966
Instruction Manual: MADE IN CHINA
3
Hex Cap Screws : 7/16 in x 2
4 in
Test
Disconnected
800A/1600A 2000A/2500A
in/mm in/mm
in/mm in/mm
9(228.5)
9(228.5)
5.08(129) 5.08(129)
5.08(129) 5.08(129)
6.44(163.5)
6.44(163.5)
F 8.46(215) 8.46(215) F 12.99(330) 8.46(215)
3.17(80.5) 3.17(80.5)
3.58(91) 8.64(219.5) 3.58(91) 8.64(219.5)
0.47(12)
0.47(12)
12.24(311)
10.55(268)
12.24(311)
10.55(268)
5.91(150)
5.91(150)
Datum X
Datum X
8× 0.24 (6)
8× 0.24 (6)
Datum Y
Datum Y
3.17(80.5)
3.17(80.5)
Max overlap 2.36(60)
Max overlap 2.36(60)
0.98(25)
0.98(25)
3.46(88)
4.53(115) 4.53(115)
3.46(88)
5.24(133)
5.24(133)
16× 0.51 13
12× 0.51 13
1.77(45)
F
0.88(21.5)
1.77(45)
0.63(16)
0.88(21.5)
0.63(16)
10.06(255.5)
10.06(255.5)
18 19
18 19
in/mm in/mm
in/mm
in/mm
9(228.5)
9(228.5)
5.08(129)
5.08(129)
5.08(129)
6.44(163.5)
5.08(129)
6.44(163.5)
F 12.99(330) 8.46(215)
F 8.46(215) 8.46(215)
3.17(80.5)
3.17(80.5)
3.58(91) 8.64(219.5)
3.58(91) 8.64(219.5)
0.47(12)
0.47(12)
10.55(268)
12.24(311)
12.24(311)
10.55(268)
5.91(150)
5.91(150)
Datum X
Datum X
8× 0.24 (6)
8× 0.24 (6)
F
F Datum Y
Datum Y
3.17(80.5)
3.17(80.5)
Max overlap 2.36(60)
Max overlap 2.36(60)
0.59(15)
4.53(115) 4.53(115) 4.53(115)
0.59(15)
5.24(133)
0.88(21.5)
5.24(133)
0.94(25)
0.94(25)
2.36(60)
F 10.06(255.5)
2.36(60)
10.06(255.5)
20 20 21 21
9(228.5)
9(228.5)
5.08(129) 5.08(129)
5.08(129) 5.08(129)
6.44(163.5)
6.44(163.5)
F 8.46(215) 8.46(215) F 12.99(330) 8.46(215)
3.17(80.5) 3.17(80.5)
3.58(91) 8.64(219.5) 3.58(91) 8.64(219.5)
0.47(12)
0.47(12)
5.91(150)
10.55(268)
12.24(311)
5.91(150)
10.55(268)
12.24(311)
Datum X Datum X
3.17(80.5)
Datum Y
3.17(80.5)
Datum Y
4.53(115) 4.53(115)
4.53(115) 4.53(115) 4.53(115)
0.79(20) Max overlap 3.31(84)
0.79(20) Max overlap 3.31(84)
3.46(88)
3.46(88)
5.24(133)
5.24(133)
24× 0.51 13
32×0.51 13
1.77(45)
1.77(45)
0.88(21.5)
0.88(21.5)
0.63(16)
0.63(16)
0.69(17.5) 0.69(17.5)
9.53(242) 1.77(45) 9.53(242) 1.77(45)
22 23
22 23
9(228.5)
9(228.5)
5.08(129)
5.08(129)
5.08(129)
6.44(163.5)
5.08(129)
6.44(163.5)
F 12.99(330) 8.46(215)
F 8.46(215) 8.46(215) 3.17(80.5)
3.17(80.5)
3.58(91) 8.64(219.5)
3.58(91) 8.64(219.5)
12.48(317) 7.95(202)
7.95(202) 7.95(202) 14.61(371)
14.61(371) 12.91(328)
0.47(12)
12.91(328)
0.47(12)
10.55(268)
5.91(150)
12.24(311)
10.55(268)
12.24(311)
5.91(150)
Datum X
Datum X
8× 0.24 (6) F
F Datum Y
3.17(80.5)
8× 0.24 (6)
Datum Y
3.17(80.5)
Max overlap 3.31(84)
0.79(20)
0.69(17.5)
Max overlap 3.31(84)
1.77(45)
3.46(88)
4.53(115) 4.53(115) 24× 0.51 13 0.88(21.5)
0.79(20)
0.69(17.5)
1.77(45)
3.46(88)
5.24(133)
24× 0.51 13 0.88(21.5)
1.77(45)
5.24(133)
1.77(45)
2.36(60)
F
2.36(60)
9.53(242) 1.77(45)
F
9.53(242) 1.77(45)
24 24 25 25
6.06(154) 6.06(154)
6.06(154) 6.06(154)
9.00(228.5)
9.00(228.5)
5.08(129)
5.08(129) 5.08(129)
5.08(129)
6.44(163.5)
6.44(163.5)
C F 13.03(331) 8.50(216)
3.17(80.5) 8.50(216) 8.50(216)
F
3.17(80.5)
M 3.58(91) 8.64(219.5) C
12.52(318) 7.99(203)
CM
14.61(371) Y
MY
12.91(328) CM
14.61(371)
0.47(12)
CY MY
12.91(328)
0.47(12)
CMY CY
10.55(268)
12.24(311)
10.55(268)
12.24(311)
K CMY
5.91(150)
5.91(150)
Datum X
K Datum X
3.17(80.5)
3.17(80.5)
4.53(115) 4.53(115)
1.04(26.4) 4.53(115) 4.53(115) Max overlap 3.46(88)
Max overlap 3.46(88)
0.25(6.4) 0.33(8.5) 0.33(8.5) 3.35(85) 4.53(115) 4.53(115) 4.53(115)
1.04(26.4) 4.53(115) 4.53(115) 4.53(115)
3.35(85)
0.25(6.4) 0.33(8.5) 0.33(8.5)
6.02(153)
6.02(153)
64× 0.51 13
48× 0.51 13
1.77(45)
1.77(45)
0.79(20)
0.30(7.5)
0.79(20)
0.30(7.5)
F
F
0.79(20)
11.30(287) 1.77(45)
26
27
0.67(17)
0.67(17)
0.43 11 0.43 11
6.89(175)
F
6.89(175)
F 0.43(11)
0.43(11)
3.86(98)
3.86(98)
F
F 4.37(111)
4.37(111)
(Connection position)
(Connection position)
6.14(156) 12.38(314.5)
6.14(156) 12.38(314.5)
(Disconnection position)
(Disconnection position)
14.61(371)
14.61(371) 6.06(154) 6.06(154)
6.06(154) 6.06(154) 12.91(328)
8× 0.24 (6)
12.91(328) 8× 0.24 (6)
5.79(147) 6.10(155)
9.07(230.5)
5.79(147) 6.10(155)
10.55(268)
9.07(230.5)
14.88(378)
5.09(129)
10.55(268)
14.88(378)
1.85(47)
5.09(129)
Circuit breaker
1.85(47)
5.09(129)
6.89(157)
7.85(199.5)
7.64(194)
5.09(129)
6.89(157)
0.85(21.5)
7.85(199.5)
7.64(194)
Datum Y
0.85(21.5)
8.6(218.5) 8.6(218.5)
3.46(88)
3.46(88)
5.59(142)
5.59(142)
1.77(45)
0.85(21.5)
1.77(45)
2.28(58)
32× 0.51 13
0.85(21.5)
24× 0.51 13
2.28(58)
F 0.89(22.5)
13.94(354) 1.77(45)
0.89(22.5)
13.94(354) 1.77(45)
28 28 29 29
6.40(162.5) 6.40(162.5)
10.93(277.5) 6.40(162.5)
0.67(17)
0.67(17)
0.43 11 0.43 11
6.89(175)
6.89(175)
F F
0.43(11) 0.43(11)
3.86(98)
3.86(98)
F
F 4.37(111)
4.37(111)
(Connection position)
(Connection position)
6.14(156) 12.38(314.5)
6.14(156) 12.38(314.5)
(Disconnection position)
(Disconnection position)
5.79(147) 6.10(155)
9.07(230.5)
5.79(147) 6.10(155)
9.07(230.5)
10.55(268)
10.55(268)
5.09(129)
14.88(378)
14.88(378)
5.09(129)
1.85(47)
1.85(47)
Circuit breaker
Circuit breaker installation board
installation board
5.09(129)
6.89(157)
7.85(199.5)
5.09(129)
7.64(194)
6.89(157)
7.85(199.5)
7.64(194)
0.85(21.5)
0.85(21.5)
Datum Y
Datum Y
panel perforating size
panel perforating size
8.6(218.5) 8.6(218.5)
13.13(333.5) 8.6(218.5)
0.89(22.5)
0.89(22.5)
4.53(115) 4.53(115)
1.77(45) 3.46(88) 1.77(45)
3.46(88)
32× 0.51 13 0.85(21.5)
24× 0.51 13 0.85(21.5)
Max overlap 3.54(90)
Max overlap 3.54(90)
0.47(12)
1.77(45)
1.77(45)
0.47(12)
5.59(142)
5.59(142)
4.61(117)
F
13.94(354) 1.77(45)
4.61(117)
F
13.94(354) 1.77(45)
30 31
30 31
6.40(162.5) 6.40(162.5)
10.93(277.5) 6.40(162.5)
0.67(17)
0.67(17)
0.43 11
0.43 11
6.89(175)
F
0.43(11)
6.89(175)
F
0.43(11)
3.86(98)
3.86(98)
F F
4.37(111) 4.37(111)
(Connection position) (Connection position)
6.14(156) 12.38(314.5) 6.14(156) 12.38(314.5)
(Disconnection position) (Disconnection position)
14.61(371) 14.61(371)
6.06(154) 6.06(154) 6.06(154) 6.06(154)
12.91(328) 12.91(328)
8× 0.24 (6) 8× 0.24 (6)
5.79(147) 6.10(155)
5.79(147) 6.10(155)
9.07(230.5)
9.07(230.5)
10.55(268)
10.55(268)
14.88(378)
5.09(129)
5.09(129)
14.88(378)
1.85(47)
1.85(47)
Circuit breaker
Circuit breaker installation board
installation board
5.09(129)
6.89(157)
5.09(129)
7.85(199.5)
6.89(157)
7.64(194)
7.85(199.5)
7.64(194)
0.85(21.5)
0.85(21.5)
Datum Y
Datum Y
panel perforating size
panel perforating size
13.13(333.5) 8.6(218.5)
8.6(218.5) 8.6(218.5)
3.46(88)
3.46(88)
5.59(142)
5.59(142)
1.77(45)
0.85(21.5)
1.77(45)
64× 0.51 13
2.28(58)
F
0.85(21.5)
F
13.94(354) 1.77(45)
0.89(22.5)
13.94(354) 1.77(45)
32 33
32 33
in/mm in/mm
in/mm in/mm
0.67(17)
0.67(17)
0.43 11
0.43 11
6.89(175)
F
0.43(11)
6.89(175)
F
0.43(11)
3.86(98)
F 3.86(98)
4.37(111)
4.37(111) F
6.14(156) 12.38(314.5)
6.14(156) 12.38(314.5)
14.61(371)
14.61(371)
12.91(328) 8× 0.24 (6) 6.06(154) 6.06(154)
12.91(328) 6.06(154) 6.06(154)
8× 0.24 (6)
5.79(147) 6.10(155)
5.79(147) 6.10(155)
10.55(268)
9.07(230.5)
14.88(378)
10.55(268)
9.07(230.5)
1.85(47)
14.88(378)
5.09(129)
Circuit breaker
1.85(47)
5.09(129)
installation board Circuit breaker
installation board
5.09(129)
6.89(157)
5.09(129)
0.85(21.5)
7.85(199.5)
6.89(157)
7.64(194)
7.85(199.5)
7.64(194)
0.85(21.5)
Datum Y
panel perforating size Datum Y
panel perforating size
8.6(218.5) 8.6(218.5)
13.13(333.5) 8.6(218.5)
0.89(22.5)
4.53(115) 4.53(115)
0.89(22.5)
1.77(45)
0.25(6.5)
1.77(45)
1.2(30.5)
0.25(6.5)
1.2(30.5)
5.59(142)
5.59(142)
4.61(117)
F
13.94(354) 1.77(45)
4.61(117)
F
13.94(354) 1.77(45)
34 35
34 35
0.67(17)
0.67(17)
F F
6.89(175)
0.43(11)
6.89(175)
0.43(11)
3.86(98)
4.25(108) F
3.86(98) (Connection position)
4.25(108)
F 6.02(153) 12.38(314.5)
(Connection position) (Disconnection position)
C 6.02(153) 12.38(314.5)
(Disconnection position) 14.61(371) 6.06(154) 6.06(154)
M
6.06(154) 6.06(154)
12.91(328)
14.61(371) 8× 0.24 (6)
Y
12.91(328)
5.79(147) 6.10(155)
8× 0.24 (6)
9.23(234.5)
9.04(229.5)
CM
10.55(268)
5.08(129)
14.88(378)
5.79(147) 6.10(155)
5.08(129)
1.85(47)
10.55(268)
MY
Circuit breaker
14.88(378)
installation board
1.85(47)
CY
5.08(129)
Circuit breaker
6.22(158)
5.08(129)
7.89(200.5)
7.68(195)
6.22(158)
installation board
7.89(200.5)
7.68(195)
CMY
0.85(21.5)
K Datum Y
0.85(21.5)
3.94(100)
3.94(100)
5.98(152)
5.98(152)
2.36(60)
0.79(20)
2.36(60)
96× 0.51 13
1.85(47)
0.79(20)
F
1.85(47)
0.79(20)
72× 0.51 13
F
0.79(20)
16.28(413.5) 1.57(40)
16.28(413.5) 1.57(40)
36
37
⑤Mounting limit clamp ⑥Install the bus bar and lock the screws with
tightening torque (15~17)N.m
Note:
1. The bar code of Neutral Current Transformer must be the same as that of the circuit breaker and is not interchangeable;
2. Connect the conductor of Neutral Current Transformer to 28#, 29# terminals.
1 Application
15~17N·m
ELM10 is used to reduce arc hazards and protect personal safety during product mainte-
nance. It should be used together with power circuit breaker which has ARMs protection
function.
Hot and humid Relative humidity should not exceed 50% at +40℃;up to 90% at +20℃;
atmospheric conditions
Upper supply
Lower supply
LSC10 4 Selection
Lockable switch cover 0A Se�ng Maintain
Maintain Maintain
N A B C ARMS
Note:LSC10 is optional unit. Note whether to purchase LSC10. Table 2 7). To turn off ARMs mode,150 System set
the operation as follow:(Note: Prohibit
OFFto turn off ARMs
signal mode,
On On
when ELMs in “ON”state) 100 Protectset Ii=2500A
Ii=2500A Ii=5000A
Model Description Maintain (2.0 x In) No (4.0 x In)
ELM10 ELM10 50 Measure ARMS
(2.0 x In)
ELM10 Energy-Limiting Maintenance Switch (ELM Switch) 0A Se�ng 0 System Record
set DI/DO DI1
signal
5 Debug LSC10 Lockable switch cover
N A B C
System set Clock Set DO1 Func Set
150
Protectset Gauge Set DO2 ARMS
1). ELM10 module needs external power supply to work normally; 100 7). To turnTest/Lock
off ARMs mode, the operation as follow:(Note: Prohibit to turn off ARMs mode,
Note:LSC10 is optional unit. Note whether to purchase LSC10. Maintain DO3 State:1
2). ELM10 module has two power input interface unit. Terminal 1 and 2 are connected to 50 when ELMsCom in “ON”state)
Measure set DO4
AC85-528V or DC110-600V,terminal 5 and 6 are connected to DC24V. Choose one type N.C
0 Record DI/DO DI1
power supply input;
0A Se�ng System set DI/DO DI1
3). Connect signal output terminal 3 and terminal 4 of ELM10 module to terminal 20 and
5 Debug of air circuit breaker respectively;
terminal 21 of secondary disconnector
N A B C
System set Clock Set DO1 Func Set
150
4). After ELM10 is powered on, the power indicator(red) is on. By default, the SWITCH is Protectset Gauge Set DO2 ARMS
1). ELM10 module needs external power supply to work normally; DI1 100 DI1
in OFF position, when the SWITCH is rotated to the ON position, the blue indicator is on and Maintain Test/Lock DO3 State:1
2). ELM10 module has two power input interface unit. Terminal 1 and 2 are connected Func Setto 50 Func Set
ARMs function is opened to connect electrical trip unit. The default protection setting value is ARMS signal Measure No Com
ARMS set
signal DO4
AC85-528V or DC110-600V,terminal 5 and 6 are connected to DC24V. Choose oneARMS type N.C
State 10 OFF DI/DO DI DI1
Changed
2In. To change the protection setting, please adjust it on trip unit. Record
power supply input; State:1 State:1
5). Before ELM10 is connected to trip unit,
3). Connect open
signal the DI1
output function
terminal of trip
3 and unit and
terminal 4 ofset to
ELM10 module to terminal N.C20 and N.C
ARMs mode. The operationterminal
process21 asof
follow:
secondary disconnector of air circuit breaker respectively;
4). After ELM10 is powered on, the power indicator(red) is on. By default, the SWITCH is DI1 DI1
in OFF position, when the SWITCH is rotated to the ON position, the blue indicator is on and
Se�ng set to connectDI/DO Func Set Func Set
0A ARMs functionSystem
is opened electrical trip unit. The
DI1 default protection setting value is ARMS signal No ARMS signal
ARMS OFF
N A B C 2In. To change
System set theSet
Clock DO1 please adjust itFunc
protection setting, Set unit.
on trip 6 ENVIRONMENTAL PROTECTION State 1 DI Changed
150 State:1 State:1
Protectset
5). Before ELM10 to trip unit, open theARMS
is connectedDO2
Gauge Set DI1 function of trip unit and set to
100 In order to protect environment,
N.C when the product or its parts are scrapped, please
N.C properly
MaintainARMs mode.Test/Lock DO3 as follow:
The operation process State:1
50
dispose of them as industrial waste. Or to the recycling and treatment station according to
Measure Com set DO4 N.C
the relevant provisions of the region for classification disassembly、 recycling etc.
0 Record DI/DO DI1
7). To turn off ARMs mode, the operation as follow:(Note: Prohibit to turn off ARMs mode,
when ELMs in “ON”state)
Accessories
Undervoltage release/UVT Theundervoltage
The undervoltagerelease releaseis is
anan optional
optional device
device on on
bothboth manually
manually andand electrically
electrically operated
operated air
circuit Rated Current /
Theswitch
undervoltage release Itisopens an optional device on both manually andfalls
electrically operated circuit
breakers.disconnectors.
It opens the breaker when theitsswitch
supplywhen its falls
voltage supply voltage
to 30–60% to 30–60%
of rated voltage. of rated
If the voltage.
release Voltage /V
A
breakers.
If not It opensisthe
the energized
release breaker when its supply voltage falls to 30–60% of rated voltage. If the release
is tonot
85% energized to 85%
of its supply of itsthe
voltage, supply voltage,
circuit breakerthe switch
cannot bebreaker cannot be or
closed electrically closed
manually.
is not energized
electrically or to 85% of its supply voltage, the circuit breaker cannot be closed electrically or manually.
manually. 240 5
Voltage
AC /V Rated Current /A
Voltage240
/V 480
Rated 2
Current /A
The undervoltage release is an optional device on both manually and electrically operated circuit AC Voltage /V Rated 5Current /A
240
480
110
25 5 0.25
breakers. It opens therelease
Undervoltage
Undervoltage breaker when
releaseratings: its supply voltage falls to 30–60% of rated voltage. If the release
ratings: ACDC 240
is Undervoltage release
not energized to 85% of itsratings:
supply voltage, the circuit breaker cannot be closed electrically or manually. AC 480
110 220
0.252 0.25
DC 480
110 2
0.25
Operational
Operational Inrush/
In rush / DC 220 0.25
Operational
voltage
voltage Dropout
Dropout In rush /continuous
continuous 110
220 0.25
0.25
Control
Control voltage
rangrang
e e Dropout
voltage
voltage continuous
power power Operating
Opening
DC
Control rang
voltagesrelease ratings:
voltage e85–110%
85–110% voltage
30–60%
30–60% power consumption
consumptio n Opening
time (ms)
time (ms)
220 0.25
Undervoltage
voltage 85–110% 30–60% consumptio n time (ms)
24 Vdc Vdc
24-30 20–26 Vdc
20–33 7–147–14
Vdc Vdc 250 W/4.5 W W 7070
24 Vdc 20–26 Vdc Vdc 7–14 Vdc 250 W/4.5250WW/4.5 70
Operational
41–53
In rush / The auxiliary contact remotely monitors ON/OFF position of power circuit breaker or
48 Vdc Vac/Vdc
48-60 41–66Vdc Dropout14– 14–
29 Vdc 275 W/4.5 W 70
48 Vdc voltage
41–53 Vdc Vac/Vdc voltage
14– 29 Vdc29 Vdc continuous 275WW/4.5
275 W/4.5 W 70 70
Non-automatic Switch from remote place.
Control rang e power Opening
110-130
voltage110-130Vac/Vdc
Vac/Vdc 85–110%94–143 Vac/Vdc
94–143 Vac/Vdc 30–60% 33–78Vac/ Vdc
33–78Vac/ 275 W/4.5 W (ms) 70
110-130 Vac/Vdc 94–143 Vac/Vdc 33–78Vac/ Vdc Vdcconsumptio n 275
275 W/4.5 WW/4.5
time W 70 70 Contact configuration:
24 Vdc200-240Vac/
200-240Vac/Vdc 170–264V
Vdc 20–26 Vdc ac/Vdc
170–264V 7–14 Vdc60–144
ac/Vdc Vac/Vac/
60–144 Vdc250 W W/4.5W
VdcW/4.5 275 70
275 W/4.5W 70 70 44: 4NO and 4NC;66: 6NO and 6NC;
200-240Vac/ Vdc 170–264V ac/Vdc 60–144 Vac/ Vdc 275 W/4.5W 70
48 Vdc380–415 Vac
380–415
380–415 Vac Vac
323– 457 Vac
41–53 Vdc
323– 323– 457 Vac
457 Vac
114–249 Vac 275 W/4.5 450
14– 29 Vdc
114–249
114–249 Vac Vac
W W/4.5W70
450 W/4.5W
450 W/4.5W 70
70
70
44C: 4NO or 4NC;66C: 6NO or 6NC.
110-130 Vac/Vdc 94–143 Vac/Vdc 33–78Vac/ Vdc 275 W/4.5 W 70
Shunt trip release/SHT
Shunt release/SHT 200-240Vac/ Vdc 170–264V ac/Vdc 60–144 Vac/ Vdc 275 W/4.5W 70 Motor operator
Shunt trip release/SHT
380–415 Vac 323– 457 Vac 114–249 Vac 450 W/4.5W 70
Shunt
Shunt trip ratings:
Shunt triptrip ratings:
ratings:
Operational Irush/
Operational
Operational
voltage Irush/ Inrush/
continuous
Shunt trip ratings:
Control voltage
voltage
rang e continuous
continuous
power Opening
Control
Control
voltage rang rang
e e
70–110% power power n
consumptio Opening
timeOperating
(ms)
voltages
voltage 70–110%
70–110% consumption
consumptio n time (ms)
time (ms)
Operational Irush/
24-30 Vdc voltage17– 33 Vdc continuous250 W/4.5 W 35
Control VdcVdc
24-30
24-30 rang 17–
e 33 Vdc
17– 33 Vdc power 250 W/4.5 W
250 W/4.5 WOpening 35 35
The electric motor charges the closing spring of mechanism when the circuit breaker is
48-60 V dc
voltage 70–110% 34–66 V dc consumptio275n W/4.5 W time (ms) 35
48-60 V dcVac/Vdc
48-60 34–66 V dc Vac/Vdc
34–66 275 W/4.5 W
275 W/4.5 W 35 35 closed.
24-30110-130
Vdc Vac/Vdc 77–143Vac/Vdc
17– 33 Vdc W W/4.5 W
250 W/4.5275 35 35
110-130 Vac/Vdc
110-130 Vac/Vdc 77–143Vac/Vdc
77–143Vac/Vdc 275 W/4.5 W
275 W/4.5 W 35 35 Factory installed only.
48-60 208-240Vac/
V dc Vdc 34–66 V146–264V
dc ac/Vdc 275 W/4.5275
W W/4.5W 35 35
208-240Vac/ Vdc Vdc
20 8-240 Vac/ 146–264V ac/Vdc
146–264V ac/Vdc 275 W/4.5W
275 W/4.5W 35 35
Mechanical charging handle can be used when maintaining or without power supply.
110-130 Vac/Vdc 77–143Vac/Vdc 275 W/4.5 W 35 Equipped with a limit switch contact which signals that spring is charged.
380-415Vac 266-458.5Vac 275W/4.5W 35
Closing release/XF 208-240Vac/ Vdc 146–264V ac/Vdc 275 W/4.5W 35
Closing release/XF
Closing release/XF Miss insertion prevent device
Closing release/XF
The closing release is an optional device. It remotely closes the circuit breaker
TheThe
closing release is anisoptional device. It remotely closes the circuit breaker
when closing
the coil release
is energized anby
optional device.
a voltage input.It remotely closes the air switch disconnector breaker
when therelease
coil is energized by a voltage input. closes the circuit breaker
when
The closing the coilisisanenergized by a voltage
optional device. input.
It remotely
when the coil is energized by a voltage input.
User Manual 24
User
UserManual
Manual 24
24
User Manual 44 User Manual 45
Accessories
Accessories Accessories
Safety shutter
Safety shutter OFF position keylock/KLK
Accessories
Safety shutter
It is Itthe
is the automatic
automatic safety
safety devicetotoprotect
device protectthe
the connectors
connectors ofofmain
maincircuits by by
circuits cutting off dangerous
cutting off Suitable for A32 Power circuit breaker and ASD32 No-automatic switch
contactcontact
dagerous from outside
from while
outsidethewhile
breaker
theisbreaker
draw out.
is When
draw the
out.main
Whenbreaker is drawn
the main in, the
breaker is safety Block a breaker in OFF position to ensure the breaker can not be closed
drawn shutter is safety
in, the automatically
shutter open.
is automatically open. One circuit breaker is provided with one lock and one key
OnlyOnly available
available for withdrawable
for withdrawable circuit
circuit breaker
breaker & non-automatic
& non-automatic switch.
switch. Two circuit breakers are provided with two locks and one key
Three circuit breakers are provided with three locks and two keys
Safety
Safety shutter
shutter lock lock Pushbutton lock device/VBP
It is the automatic safety device to protect the connectors of main circuits by cutting off dangerous
contact from outside while the breaker is draw out. When the main breaker is drawn in, the safety
shutter is automatically open.
Only available for withdrawable circuit breaker & non-automatic switch.
When Whthe
en tmain
he mabreaker
in breakeis r isat
at disconnected
disconnected po position,
sition, loclock
k the the
safesafety
ty shuttshutter to provent
er toprevent main The cover prevents the access to control push button of the breaker
mainbreaker
breaker pushed
pushed in.in. Factory instolled only
OnlyOnly
available
availablefor withdrawable
for withdrawable circuit breaker
circuit breaker& non-automatic
& non-automatic switch.
switch. Scope of delivery: Lockable cover (lock with key is not a part of delivery)
LockLock
is not provided.
is not provided.
WDiameter
e mainof
brethe
hen thDiameter erlock
akof the should
lock
is at d be
isconshould
necte 0.12in
be
d po n, loto
sitio0.12inck t0.22in.
hto
e s0.22in.
afety shutter toprevent main
breaker pushed in.
Only available for withdrawable circuit breaker & non-automatic switch.
Mechanical interlocks
Mechanical withwith
interlocks cables
cables Doorframes
Lock is not provided.
Diameter of the lock should be 0.12in to 0.22in.
78in/2m(max)
Circuit Circuit
diagram On/Off On/Off
diagram state state
ELM10 is used to mitigate arc hazards and protect personal safety during product
maintenance. It should be used in coordination with Power Circuit Breakers with ARMs
protection function.
LSC10 is lockable switch cover for ELM10 switch with a 7mm locking hole, it is an
optional unit, please comment if is required when purchasing.
TA
1 2 SA SAL Smart Uint Control power
1 2 SA
XT TA
1 2 3 7 10 11 12 21 23 25 27 29 31 33 35 38 41 43 45 47 49 51 53 55 15 17 19 21 59 62 65 FU
XT
1 2 3 7 10 11 12 21 23 25 27 29 31 33 35 38 41 44 47 50 53 56 59 62 65 FU
A+ B- Shield ground
QF - circuit breaker SA - position switch
Smart Uint power Modbus interface when control voltage is DC,please identify positive and negative poles TA - current transformer SAL - micro switch
A+ B- Shield ground
No wiring if communication XT - terminal FU - fuse QF - circuit breaker SA - position switch
function is not available TA - current transformer SAL - micro switch
Smart Uint power Modbus interface when control voltage is DC,please identify positive and negative poles
When H-type controller, 6 NO and 6NC auxiliary contacts are selected at the same time, XT - terminal FU - fuse
No wiring if communication
please refer to additional secondary circuit wiring diagram.
function is not available
User Manual 31
e
Ready to Spring Connecting Disconnecting
close contact Opening Closing Ready to
charge Closing Opening positon Test positon positon Spring Connecting Disconnecting
indication close contact Opening Closing
N indication indication indication Auiliary contact - for user indication indication indication charge Closing Opening positon Test positon positon
N indication indication indication indication Auiliary contact - for user indication indication indication
QF MD
SHT XF UVT
QF MD
Control power SHT XF UVT
Control power
SA
TA SA
TA
7 31 33 35 38 41 43 45 47 49 51 53 55 15 17 19 21 59 62 65 FU
XT
7 31 33 35 38 41 44 47 50 53 56 59 62 65 FU
User Manual 31
User Manual 52 UserManual
User Manual 31
53
Profile of SU Profile of SU
ing requirements.
CMY
3 . 0 A
a b c
Table of Models
Protection type Measurement type
a c
2: LI protection Basic type M
3: LSI protection Ammeter type A
4: LSIG protection Harmonics type H
Note: M type is LED display; A and H types are
LCD display.
Appearance Appearance
3.0 4.0
Reset after alarm
1600 1600 When the circuit breaker sends an alarm, the LCD will turn
Tsd
yellow, and the LED ALM indicator will be ON. In this case, alarm
record need to be check. After the alarm is cleared, the control-
ler can return to the normal state.
Thermal memory
Tr=2s(@6Ir)
Y
K
Power factor measurement
Tsd
Electric energy measurement
In=1600A
Demand value measurement
Isd=4 xIr=4480A
Harmonic measurement
Tsd=0.4S
Test function
Record of operations Note: “X” of the Tsd setting knob: Disable the shor t-delay protection.
Short time delay Tsd setting panel: OFF: definite time setting area; ON: inverse time
Maintenance Trip records setting area
function Alarm records
Instantaneous parameter setting Take In=1600A as an example
Position change records
Contact wear records
Load monitoring
In=1600A
Zone Selective Interlocking
Ii=15xIn=24000A
Other RS485 communication function
functions
Digital input/output DI/DO
Real time clock Note: X=off
Instantaneous
LED display
Ground-fault protection time setting Take In=1600A as an example
Tri-color LCD display
HMI LED status indication
Tg
Button operation In=1600A
Knob setting Ig=880A
USB test port Tg=0.4S
Note: Please Contact Noark if customers use functions like Load monitor, Zone-Selection Interlocking and digital input/out-
Note: “X” of the Tg setting knob: Disable the ground protection.
put DI/DO. ground Tg setting panel: OFF: definite time setting area; ON: inverse time
setting area
Button Operating Instructions The smart unit is configured with one default inter- Default interface after Starup.
face and four main menus.
Buttons can be used to set other functions, such as overvoltage, The default interface displays the continuously
undervoltage, voltage unbalance, Over-frequency, Under-fre- Display the current value of each
measured phase currents: Ia, Ib, Ic, and In.
quency, reverse active Power and harmonic protection, load phase in the default interface.
Main menu of system setting
monitoring, etc. Refer to relevant chapters for specific details. Press or to switch the current
Main menu of protection setting
values of the phase A, B and C.
Main menu of measurement
Press“OK”once to enter the“Setting”interface and menus Main menu of record
Press in the default interface
(e.g.“System Setting”and“Protect Set”). Note: The basic type controller uses LED display menu.
In the“Setting”interface, set system parameters by pressing to enter the”Setting” interface.
the“ ”and“ ”buttons.
C
Setting
Example: Current unbalance adjustment Press or to adjust the menu
System set
M
sub-menu.
CM
Open the initial interface. Measure
Press to return to the default
MY
Record
Press to enter the“Setting”interface. interface.
CY
Press and to the“I Unbalance”interface, and then press to open the“I Unbalance”interface.
V.U Off
Voltage unbalance Alarm: (start value, time) & (return value, time) setting
Trip: start value & time setting
V.harmonic Off
Voltage harmonic Alarm: (start value, time) & (return value, time) setting
Trip: start value & time setting
11 F4 Communication setting
C
15 F8 View of LSIG setting
M
16 U. Current unbalance
Y
17 3PHS Test setting of LSI current protection
CM
18 Vector and ground-fault protection test setting
MY
19 Test confirmation status
CY
20 gdr Modbus-RUT address setting Main function menus and settings of the M type control unit :
CMY
21 A.- Modbus-RUT address selection F0: Neutral protection setting: 50%, 100%, OFF.
K
22 bPS means Modbus-RUT baud rate setting F1: Current unbalance setting: ON (OFF), current unbalance rate setting, delay time setting.
23 TRIP Trip status F2: Thermal memory setting: ON (OFF), thermal memory recovery time setting.
24 RUN Running status F3: Test function setting: LSI protection test, ground-fault protection test.
F4: Communication setting: communication address (1-247), baud rate (9600, 19200).
25 SET Normally ON: setting status
F5: Trip record view: Take the instantaneous trip for example. Press “OK” in the default interface, select the F5 menu by pressing “UP”
26 ALM Alarm status
and “DOWN” , and then press “OK” to enter the trip record view interface. Select the serial number (e.g. 01) of record, and press
27 NULL No information
“OK” . The instantaneous trip current interface will appear. The trip time interface can be viewed by pressing “UP” and “DOWN” .
28 OPEN Open
29 CLSE Closed
30 E1 Magnetic break
31 E2 CT break
32 E3 Action rejection
33 LSIG curve. The full display means normal operation. In case of fault tripping, the corresponding segment will flash.
Selective protection L S I
CM
MY
CY
User Manual 66
C
CM
MY
CY
CMY
http://na.noark-electric.com
ZA32202209UL
User Manual 34