Professional Documents
Culture Documents
RADspeedPro ConnectionDRtoGenerator en KO2 Integração Com DAR
RADspeedPro ConnectionDRtoGenerator en KO2 Integração Com DAR
Connect DR to Generator
Service Management Dept.
SHIMADZU Corp.
Contents
1. Required PCB Board
2. Install PCB Board
3. Connect serial communication cable
4. Connect X-ray exposure signal cable
Appendix How to get logs of serial communication
Appendix ARCNET setting when using COMDAR
1. Required PCB Board
Requires 2 cable when connecting DR and Generator
• Serial communication cable
• X-ray exposure signal cable
PCB board that cables are connected to are different depending on DR combined
・ SF-X2 (Edge) with Fuji Film or Serial Exposure (DDR) with Konica Minolta
→ Require COMDAR-2009COMDAR-2009
・ Other cases
→ available to use either of COMDAR-2009 or COM I/F-2002
1. Required PCB Board
X-ray exposure signal cable should be connected to COMDAR-2009
or TERMINAL-2002 / TABLE I/F
・ SF-X2 (Edge) with Fuji Film or Serial Exposure (DDR) with Konica Minolta
→ Require COMDAR-2009
・ Other cases
→ TABLE I/F-2002 (or TERMINAL-2002 if TABLE I/F is not mounted in the cabinet)
2. Install PCB Board
Install COMDAR-2009 In case of SF-X2 system (Edge system),
Should be installed beneath UD CONT 2-3 on JP9 should be short-cut for supplying power
Connect to CH-200
Connect by selecting either cable in the table below
UD cable CH Note
TERMINAL-2002 X-RAY I/F Cable B CHC200/CHC200PA Without TOMOS
COMDAR- CN9 J6 P/N 563-59442 J25
2009
COMDAR-2009 CH-XGEN COMDAR CABLE CHC200/CHC200PA With TOMOS
CN MECA J13 P/N 565-15048-06 J20
COM I/F-2002
In case of SF-X2 (Edge) system,
1-2 on JP4 should be short-cut
for supplying power
Connect to CH-200
UD cabinet Cable CH cabinet
Terminal 2002 J6 J6 J25 J25 CHC-200
422 I/F-2002
3. Connect serial communication cable
Connect to COMDAR-2009
select either way of ① or ②
COM I/F
562-23733, COM conversion cable
9pin DR
9pin D-Sub
J7
3. Connect serial communication cable
[Communication] Setting
In case that system has touch-panel type
3. Connect serial communication cable
[Communication] Setting ・ In case of SF-X2 system ・ Others
In case that system has touch-panel type
No
Yes
TABLE I/F-2002 Connect to TABLE I/F-2002
No
Connect toTERMINAL-2002
4. Connect X-ray exposure signal cable
No
Yes
TABLE I/F-2002 Connect to TABLE I/F-2002
No
Connect toTERMINAL-2002
Refer to Installation manual (M501-E356) 2.9.4 Connecting with Fujifilm SF-X2 system
Table 2 2
Stand 5 3
Free 3 2
Table 2 2
Stand 5 3
Free 3 2
・TABLE I/F out-1 No.9 : [902]… Audio output signal for Auto Voice of Serial Radiography
・DAR I/F out-1 No.1 : [784]… Hand Switch signal of CH-200
・DAR I/F out-2 No.15 : [782]… Table Protocol
・DAR I/F out-2 No.16 : [783]… Stand Protocol
・DAR I/F out-3 No.7 : [808]… RDY1 for Table Serial Radiography
・DAR I/F out-3 No.8 : [611]… RDY2 for Table Serial Radiography
・DAR I/F out-3 No.9 : [612]… RDY2 for Stand Serial Radiography
・DAR I/F out-3 No.5 : [809]… RDY1 for Stand Serial Radiography (when COMDAR-2009
used)
4. Connect X-ray exposure signal cable
No
Yes
TABLE I/F-2002 Connect to TABLE I/F-2002
No
Connect toTERMINAL-2002
4. Connect X-ray exposure signal cable
Connect to TABLE I/F-2002 (In case of Fujifilm DR)
Connect When using Tech System 6
DR system
TABLE I/F-2002
1ch 2ch SHOT GO B
SHOT GO A
OUT7A SHOT1 RDY 2 SHOT2 RDY 2
OUT7B SHOT1 #RDY 2 SHOT2 #RDY 2
IN4A SHOT1 GO A SHOT2 GO A
IN4B SHOT1 GO B SHOT2 GO B
OUT6A SHOT1 RDY 1 SHOT2 RDY 1 SHOT #RDY 2
SHOT RDY 2
OUT6B SHOT1 #RDY 1 SHOT2 #RDY 1 SHOT #RDY 1
SHOT RDY 1
・ [Signal] setting (no need to change anything)
4. Connect X-ray exposure signal cable
Connect to TABLE I/F-2002 (In case of Fujifilm DR)
Connect When using Tech System 5
DR system
TABLE I/F-2002
1ch 2ch SHOT GO B
SHOT GO A
OUT1A SHOT1 RDY 2 SHOT2 RDY 2
OUT1B SHOT1 #RDY 2 SHOT2 #RDY 2
IN0A SHOT1 GO A SHOT2 GO A
IN0B SHOT1 GO B SHOT2 GO B
OUT0A SHOT1 RDY 1 SHOT2 RDY 1 SHOT #RDY 2
SHOT RDY 2
OUT0B SHOT1 #RDY 1 SHOT2 #RDY 1 SHOT #RDY 1
SHOT RDY 1
・ [Signal] setting (no need to change anything)
4. Connect X-ray exposure signal cable
Connect to TABLE I/F-2002 (In case of Fujifilm DR)
Connect When using Tech System 4
DR system
TABLE I/F-2002
1ch 2ch SHOT GO B
SHOT GO A
OUT3A SHOT1 RDY 2 SHOT2 RDY 2
OUT3B SHOT1 #RDY 2 SHOT2 #RDY 2
IN1A SHOT1 GO A SHOT2 GO A
IN1B SHOT1 GO B SHOT2 GO B
OUT2A SHOT1 RDY 1 SHOT2 RDY 1 SHOT #RDY 2
SHOT RDY 2
OUT2B SHOT1 #RDY 1 SHOT2 #RDY 1 SHOT #RDY 1
SHOT RDY 1
・ [Signal] setting (no need to change anything)
4. Connect X-ray exposure signal cable
Connect to TABLE I/F-2002 (In case of Canon DR)
Connect When using Tech System 6
No
Yes
TABLE I/F-2002 Connect to TABLE I/F-2002
No
Connect toTERMINAL-2002
4. Connect X-ray exposure signal cable
Connect to TERMINAL-200 (In case of Fujifilm DR)
Connect When using Tech System 2
TERMINAL I/F-2002 DR system
SHOT #RDY 2
X1-1B2 SHOT1 RDY 2
SHOT RDY 2
X1-1B2 SHOT1 #RDY 2
X2-0V SHOT1 GO A SHOT #RDY 1
SHOT RDY 1
X2-1B1 SHOT1 GO B
X1-KC2 SHOT1 RDY 1 SHOT GO B
X1-KC2 SHOT1 #RDY 1 SHOT GO A
・ TERMINAL-2002
SW1-1 ON
SW2-1 OFF
・ [Signal] setting (no need to change anything)
4. Connect X-ray exposure signal cable
Connect to TERMINAL-200 (In case of Canon DR)
Connect When using Tech System 3
TERMINAL I/F-2002 DR system
#1 WHT
X1-2B2 #1 WHT #2 YEL
X1-2B2 #2 YEL
X2-0V #3 ORG
X2-2B1 #4 GRY
X1-KC - #4 GRY
X1-KC - #3 ORG
・ TERMINAL-2002
SW1-2 ON
SW2-2 OFF
・ [Signal] setting (no need to change anything)
4. Connect X-ray exposure signal cable
Connect to TERMINAL-2002 (In case of Konica Minolta DR)
Connect when using Tech System 2
When to use XG cable set DC(A6DE) or XG cable set 2(A7R7) ※(A7R7)
Ex.)