Professional Documents
Culture Documents
TC-31A Alarm Message
TC-31A Alarm Message
2005/10/25 8 - 29 eTCOMCOOP8-4
TC-31A/22A/S2A
Chapter 8 Alarm message 32A/R2A/20A/S2B
2005/10/25 8 - 30 eTCOMCOOP8-4
TC-31A/22A/S2A
32A/R2A/20A/S2B Chapter 8 Alarm message
2504 1 1
END NOTICE
COUNTER2
the end notice number.
The workpiece counter has attained 8
END NOTICE the end notice number.
2505 1 1 COUNTER3 The workpiece counter has attained
END NOTICE the end notice number.
2506 1 1 COUNTER4 The workpiece counter has attained
END NOTICE the end notice number.
2507 1 1 NOT CLOSING Attempt of runnung the machine Close the door or set the interlock unit to
DOOR while the door is open and the OFF.
interlock unit is ON.
2508 1 1 IN AUTO The mode is changed during center Finish the center alignment operation.
ALIGNMENT aliginment.
2509 1 1 RELEASE An attempt is made to execute the Turn OFF the respective lock status before
MACHINE center alignment in the machine executing the center alignment.
LOCK lock.
2510 1 1 ZERO RTN An attempt is made to return to Release the machine lock before executing
COMMAND M.Z. point during the machine the zero point return.
ERR lock.
2511 1 1 DR OPEN The door was opened during Close the door and restart the operation. The
SPNDL STOP spindle rotation (the door interlock spindle starts rotating from the position
is effective). when the operation was stopped.
2512 1 1 TOO SMALL TM Tap time constant set by M code Set the time constant by M code
CONST was smaller than the minimum tap appropriately for tap rotation.
time constant operable for tap
rotation.
2513 1 1 PALLET POS A memory operation is commanded Change to the manual mode and index pallet
ERROR while the pallet is not indexed. with [C INDEX] key.
2514 1 1 INNER DOOR The inner door is opened in the Close the inner door and push [CAN] key.
OPEN operation.
2515 1 1 OUTER DOOR The C axis is going to rotate while Close the outer door, or turn off the safety
OPEN the safety switch is ON and the switch.
outer door is open. Or machine is
going to be operated while the
pallet is not indexed.
2005/10/25 8 - 31 eTCOMCOOP8-4
TC-31A/22A/S2A
Chapter 8 Alarm message 32A/R2A/20A/S2B
2517 1 1 DIFFER FROM The program different from the one Check the pallet program number set to user
PLT PRG set to user parameter (quick table) parameter (quick table).
was selected in memory operation
mode.
2518 1 1 STROKE OVER When the pallet beyond its stroke, Press the [+c] or [-c] key to move the C-axis
(C) the [z. rtn] or [p. idx] key was between -180.000 degrees and 0.000
pressed. degrees, and retry operation.
2519 1 1 SPARE TOOL Life of tool used in machining is
USING over.
2520 1 1 MEASUREMEN Switching the mode was attempted Complete zero position measurement.
T ON during zero position measurement.
2521 1 1 M406 IS ON M406 signal was on when memory Output m407 signal in MDI operation mode
operation was executed. (block operation) to turn m406 signal off.
2522 1 1 TL LF Tool life has reached the preset
EXPIRING(*) value.
The figure in brackets ( ) indicates
the tool number.
2523 1 1 INPUT DATA Data beyond the specified range is Set the data within the specified range.
ERROR set.
2524 1 1 ZERO RTN NOT An attempt is made to start Execute the zero point return.
DONE operation or automatic setting
without executing M.Z. return.
2525 1 1 PROGRAM NO An attempt is made to set the Set the program No. correctly.
ERROR program No. which is not allowed.
2526 1 1 NO COPY The program or data bank to be Check the program no. or data bank no.
SOURCE DATA copied does not exist.
2527 1 1 DST DATA A program or data bank with an Copy to a different no. or delete the existing
ALRDY EXST identical no. to those to be copied program or the data bank.
already exists.
2528 1 1 PROGRAM An attempt is made to modify the Set the PROTECT switch to OFF, and
PROTECT data while the PROTECT SW is modify the data.
ON.
8 2529 1 1 CHARACTER
NO. sOVER
Number of characters exceeds 128. Reduce a number of characters.
2530 1 1 PRGRM IN An attempt is made to edit or delete Execute it after finishing the operation.
EXECUTION the file concerning the program in
operation.
2531 1 1 SELECT AXIS The additional axis select switch Set the switch correctly.
was not set after power was turned
on.
2532 1 1 COMMUNICATI When the program or data is to be Execute it after finishing the
NG modified, the same data is in communication.
communication.
2533 1 1 REQD DATA There is no specified program or Check the program No. or data No.
NOT FOUND data.
2534 1 1 OPERATING The data desired for communication Stop operation and start communication.
COMMU DATA is currently being used.
2535 1 1 EDITING The data desired for communication Complete editing and start communication.
COMMUNI is currently being edited.
DATA
2536 1 1 COMMUNI [7 bit] is set to [character] and era Check the parameter.
PARAM ERROR is set to [trans data code] for
communication parameter.
2537 1 1 DR SIGNAL OFF DR signal was turned off during Check the parameter.
communication.
(Only when DR SIGNAL CHECK
in parameter 4 is effecive.)
2538 1 1 CS SIGNAL OFF CS signal was off during output of Check the parameter.
DC1 and DC3 codes.
2539 1 1 RC BUFFER Receiving buffer has over flown Check the parameter.
OVERFLOW (256 bytes).
2540 1 1 PARITY PARITY error has occurred during Check the parameter.
ERROR(COM) data entry.
2541 1 1 OVERRUN Overrun error (data skip) has Check the parameter.
ERROR(COM) occurred during data entry.
2542 1 1 FRAMING Framing error (stop bit was not Check the parameter.
ERROR(COM) detected) occurred during data
entry.
2005/10/25 8 - 32 eTCOMCOOP8-4
TC-31A/22A/S2A
32A/R2A/20A/S2B Chapter 8 Alarm message
2005/10/25 8 - 33 eTCOMCOOP8-4
TC-31A/22A/S2A
Chapter 8 Alarm message 32A/R2A/20A/S2B
8 2590 1 1
SIGNAL ON
Z LOCK SIGNAL The Z-axis lock signal is on. Turn it off.
ON
2591 1 1 * LOCK SIGNAL The axis 4 lock signal is on. Turn it off.
ON
2592 1 1 * LOCK SIGNAL The axis 5 lock signal is on. Turn it off.
ON
2593 1 1 * LOCK SIGNAL The axis 6 lock signal is on. Turn it off.
ON
2594 1 1 SPINDLE The spindle override is set to the Set the spindle override to 100%.
OVERRIDE ON value other than 100%.
2595 1 1 CUT FEED Cutting feed override is set to a Set the cutting feed override to 100%.
OVERRIDE ON value other than 100%.
2596 1 1 RPD TRVS Rapid feed override is set to a value Set the rapid feed override to 100%.
OVERRIDE ON other than 100%.
2597 1 1 MODE CHANGE Mode changeover prohibition Turn the signal off.
PROHIBIT signal is on.
2598 1 1 DOOR LOCKED The door OPEN/CLOSE switch
was pressed while the door was
locked.
2599 1 1 AREA SNSR The beam of the area sensor was
OBSTRUCTED obstructed while the door was
opening or closing.
2600 1 1 TOOL ALRDY The tool attempted to be set to Delete the current tool and set a new one.
REGISTRD [magazine tool] is already set for
another pot.
2601 1 1 NO TOOL IN The tool necessary for operation is Set the correct tool on the <magazine tool>
MAGAZINE not set in the magazine. screen.
2602 1 1 EDITING Deleting and copying the data bank Complete the data bank currently being
or changing the data bank number edited.
was attempted on the <directory of
memory> screen during data bank
editing.
2603 1 1 INCORRECT Replacement with a tool of
TOOL TYPE incorrect type was attempted in
manual operation mode.
2005/10/25 8 - 34 eTCOMCOOP8-4
TC-31A/22A/S2A
32A/R2A/20A/S2B Chapter 8 Alarm message
2005/10/25 8 - 35 eTCOMCOOP8-4
TC-31A/22A/S2A
Chapter 8 Alarm message 32A/R2A/20A/S2B
3212 4 2 IMPROPER The tool is not appropriate for Press the [RST] key and assign the tool
TOOL machining or the tool list has been again.
changed after the tool was assigned.
3213 4 2 TOOL LNGTH Tool length is set to 0, or not set. Set tool length after pressing [RST] key.
NOT SET
3214 4 2 N. D. NOT Number of pattern divisions is Set no. of divisions after pressing [RST]
SPECIFIED specified as 0. key.
3215 4 2 N. M. NOT Machining number of patterns is Set machining number after pressing [RST]
SPECIFIED specified as 0. key.
3216 4 2 TOO MANY N. Machining number of patterns is Set machining number again after pressing
M. specified beyond the range (999). [RST] key.
3217 4 2 RPM NOT There is no peripheral speed set in Set cutting conditions correctly after
SPECIFIED cutting condition in memory pressing [RST] key.
operation, or it is set too small.
2005/10/25 8 - 36 eTCOMCOOP8-4
TC-31A/22A/S2A
32A/R2A/20A/S2B Chapter 8 Alarm message
3221 4 2 NO PITCH Pitch data in tool menu is set to 0 or After pressing [RST] key, set pitch data.
DATA not set at all for tapping.
3222 4 2 TAP SIZE Denominator of inch screw thread After pressing [RST] key, set the nominal
ERROR size is 0. size of tap correctly.
3223 4 2 R OR L HAND ? Data on torsion direction is not set After pressing [RST] key, set torsion
in tool menu for tapping. direction.
3224 4 2 R. COMP Motion of tool dia. offset start-up Set linear command for motion of start-up
ERROR cancel is in circular arc command. /cancel after pressing [RST] key.
3225 4 2 TOO MANY Number of lines is set beyond the Press [RST] key, and set cutting width and
LINES range (99). (cutting width is 0 or tool dia. correctly
too small. or tool dia. is too small)
3226 4 2 TOO MANY Depth of cut is too small Press [RST] key and set depth of cut
INFEEDS correctly.
3227 4 2 CORNER CALC Calculation of corner r and c is not Modify corner r or c where error occurred
IMPSBL available in contouring or after pressing [RST] key.
chamfering.
3228 4 2 POCKET Too dia. is larger in pocket Press [RST] key and select a tool with dia.
IMPOSSIBLE machining as shown below: Smaller than pocket.
circle : dia.
Square : shorter one of X or Y
track : width
or tool radius is larger than corner r
of square pattern. (excl. corner r or
0)
3229 4 2 CHAMFERING Chamfer milling function comes Press [RST] key and assign tools again so
IMPSBL first in pocketing. that chamfer milling function comes after
milling function.
3230 4 2 ATC Before/after cutting, there is a tool Press [RST] key, and deleted tool change
IMPOSSIBLE change code in auxiliary function or
tool or auxiliary function of motion
code. 8
call process.
3231 4 2 RPM OVER Rotation commanded by MDI Press [RST] key and set the correct data.
results in higher spindle speed than
specified by machine parameter 1.
3232 4 2 FEEDRATE Cutting commanded by MDI results Press [RST] key and set the correct data.
OVER in higher feedrate than max. cutting
speed or max. rapid feedrate
specified by machine parameter 1.
3233 4 2 TOO LARGE R. During inner arc cutting in tool dia. Press [RST] key, and set programmed
COMP Offset, programmed radius is radius larger than tool dia. offset amount.
smaller than dia. offset amount.
3234 4 2 NO ENTRY M. Unregistered m code is to be Press [RST] key, and changed m code
CODE executed. afterwards.
3235 4 2 ILLEGAL Cutter radius compensation is done Press [RST] key, and modify approaching
APPROACH on the center of line in rectangular method afterwards.
or circular approach.
3236 4 2 ILLEGAL Cutter radius compensation is done Press [RST] key, and modify release
RELIEF on the center of line in rectangular method afterwards.
or circular release.
3237 4 2 NO CUTTING Cutting length of the line of Press [RST] key, and modify the program
LENGTH approach or release is not sufficient. afterwards.
3238 4 2 AXIS NOT No axis is designated in the Check the program.
DESIGNTD program
3239 4 2 ILLEGAL AXIS Axis is improperly designated in the Check the program.
program.
3240 4 2 R NOT The A-axis radius is not specified in Check the program.
DESIGNATED A the program.
3241 4 2 R NOT The B-axis radius is not specified in Check the program.
DESIGNATED B the program.
3242 4 2 A OUT OF During operation, A-axis operation Check the program.
COMMAND has exceeded the range of 0 ~
359.999.
2005/10/25 8 - 37 eTCOMCOOP8-4
TC-31A/22A/S2A
Chapter 8 Alarm message 32A/R2A/20A/S2B
8 3262 4 2 EXTRNL
PROGRM NO.
The selected external program no.
of the scheduled program is 5 digits
Numbers that can be used for scheduled
program are up to 4 digits.
ERR or more.
3263 4 2 TL BRK DET The detecting motion is going to Push [RST] key and check the user
POS ERR execute in the position lower than parameter1 'return position of tool breakage
the return position. detection' or make lower the 'inprocess
return ' or 'intercoordinate return ' value in
the program.
3264 4 2 RELEASE Tool replacement with the pot Release machine lock. (The tool cannot be
MACHINE number (M701 ~ 749)specified was replaced with pot specified while machine is
LOCK attempted in memory operation locked.)
with the machine locked.
3700 3 2 PROGRAM Program directory is destroyed. Delete the program and reedit it after
ERROR pressing [RST] key.
4450 1 1 RPM NOT RPM is not specified even after Specify speed and give speed command.
SPECIFED speed command is given in MDI
operation.
4451 1 1 AXIS NOT Axis data is not specified even after specify-axis data and give motion
DSGNTD motion command is given in MDI command.
operation.
4452 1 1 ILLEGAL AXIS Simultaneous cutting using 3 axes Simultaneous cutting using 3 axes is
other than x, y, and z was attempted impossible if any optional axis is included.
in MDI mode or simultaneous
cutting using 4 axes or more was
attempted.
4453 1 1 XYAB DSGNTD Tapping command is given with X, X, Y,A or B axes data can not be specified
IN TAP Y,A or B axes data set in MDI in tapping command.
operation.
4454 1 1 Z NOT DSGN IN Tapping command is given with no Specify z-axis data.
TAP z-axis data set in MDI operation.
4455 1 1 FDRATE NOT Cutting command is given with no Specify speed rate and give cutting
SPECFD feed rate set in MDI operation command.
4456 1 1 FEED NOT Kind of feed is not specified in Specify kind of feed.
SPECIFIED MDI operation.
4457 1 1 NO SCHEDULE There is no schedule program Check schedule program number.
PROGRAM available for operation.
2005/10/25 8 - 38 eTCOMCOOP8-4
TC-31A/22A/S2A
32A/R2A/20A/S2B Chapter 8 Alarm message
2005/10/25 8 - 39 eTCOMCOOP8-4
TC-31A/22A/S2A
Chapter 8 Alarm message 32A/R2A/20A/S2B
2005/10/25 8 - 40 eTCOMCOOP8-4
TC-31A/22A/S2A
32A/R2A/20A/S2B Chapter 8 Alarm message
4548 1 1 TOO LARGE Corner r is longer than the half of X Check program.
CONER R or Y whichever is shorter in a
square pocket in the pocketing
operation.
4549 1 1 APPROACH Approach radius (in program) in Check program.
RAD chamfering process is smaller than
SMALL tool radius.
4564 1 1 TOOL MENU [start] key was pressed in automatic Complete editing tool menu.
EDITING tool length measurement mode
during tool menu editing.
4565 1 1 LARGE OPE Machining data size is larger than Divide the machining data. using the
PROGRAM buffer capacity. scheduled program function, divided
machining data can be used for continuous
operation.
4566 1 1 OPEN ERROR The operation program cannot be This error may occur due to machine failure
(PROGRAM) analyzed. and the like. Contact the nearest
BROTHER approved service dealer.
4567 1 1 OPEN ERROR Cutting conditions cannot be This error may occur due to machine failure
(CUT COND) referred to. and the like. Contact the nearest
BROTHER approved service dealer.
4568 1 1 WRONG M/C When selected memory operation Reset the program to which having the same
UNIT SYS mode, the dimention unit of set dimension unit with the machine.
program is not same with the
dimention unit of machine.
2005/10/25 8 - 41 eTCOMCOOP8-4
TC-31A/22A/S2A
Chapter 8 Alarm message 32A/R2A/20A/S2B
2005/10/25 8 - 42 eTCOMCOOP8-4
TC-31A/22A/S2A
32A/R2A/20A/S2B Chapter 8 Alarm message
2003-2-19 8 - 43 eTCOMCOOP8-5
TC-31A/22A/S2A
Chapter 8 Alarm message 32A/R2A/20A/S2B
2003-2-19 8 - 44 eTCOMCOOP8-5